chemical processing scope determination matrix
TRANSCRIPT
AC7108 Rev E - Nadcap Audit Criteria for Chemical Processing
Process Specification
ApplicabilityYes Can Be Done No Remarks
Alloy Plating AMS-P-81728
Alloy Plating MIL-P-81728
Anodizing AMS-A-8625
Anodizing AMS 2482
Anodizing AMS 2488
Anodizing MIL-A-63576
Anodizing MIL-A-8625
Anodizing AMS 2468
Anodizing AMS 2469
Anodizing AMS 2470
Anodizing AMS 2471
Anodizing Other
Brush Plating MIL-STD-865
Brush Plating Other
Cadmium Plating AMS-QQ-P-416
Cadmium Plating
Cadmium Plating Other
Cadmium Plating QQ-P-416
Chemical Cleaning Acid Cleaning
Chemical Cleaning Alkaline Cleaning
Chemical Cleaning Cleaning for Adhesive Bonding
Chemical Cleaning Other
Chromium Plating AMS 2460
Chromium Plating MIL-DTL-14538
Chromium Plating AMS-QQ-C-320
Chromium Plating AMS 2406
Chromium Plating ASTM B 650
Chromium Plating MIL-C-14538
Chromium Plating Other
Chromium Plating QQ-C-320
ASTM A 165
Conversion/Phosphate Coatings MIL-DTL-13924
Process Specification
ApplicabilityYes Can Be Done No Remarks
Conversion/Phosphate Coatings MIL-DTL-16232
Conversion/Phosphate Coatings MIL-DTL-5541
Conversion/Phosphate Coatings AMS 2473
Conversion/Phosphate Coatings AMS 2474
Conversion/Phosphate Coatings AMS 2475
Conversion/Phosphate Coatings AMS 2480
Conversion/Phosphate Coatings AMS 2481
Conversion/Phosphate Coatings MIL-C-13924
Conversion/Phosphate Coatings MIL-C-5541
Conversion/Phosphate Coatings MIL-F-495
Conversion/Phosphate Coatings MIL-M-3171
Conversion/Phosphate Coatings Other
Copper Plating AMS 2418
Copper Plating MIL-C-14550
Copper Plating MIL-P-47266
Copper Plating Other
Electroless Plating Copper Other
Electroless Plating Nickel AMS-C-26074
Electroless Plating Nickel AMS 2404
Electroless Plating Nickel AMS 2405
Electroless Plating Nickel MIL-C-26074
Electroless Plating Nickel Other
Electropolishing Other
Nickel Plating AMS-QQ-N-290
Nickel Plating AMS 2403
Nickel Plating MIL-P-18317
Nickel Plating Other
Nickel Plating QQ-N-290
Paint/Dry Film AC7108/1 Must Also Be Selected
Silver Plating AMS 2410
Silver Plating AMS 2411
Silver Plating AMS 2412
Process Specification
ApplicabilityYes Can Be Done No Remarks
Silver Plating ASTM B 700
Silver Plating Other
Silver Plating QQ-S-365
Stripping MIL-STD-871
Stripping Other
Surface Treatment/Passivation AMS-2700
Surface Treatment/Passivation AMS-QQ-P-35
Surface Treatment/Passivation ASTM-A-967
Surface Treatment/Passivation ASMT-A-380
Surface Treatment/Passivation Other
Surface Treatment/Passivation QQ-P-35
Tin Plating AMS 2408
Tin Plating ASTM B 545
Tin Plating MIL-T-10727
Tin Plating Other
Tin-Lead (Alloy) Plating AMS-P-81728
Tin-Lead (Alloy) Plating MIL-P-81728
AMS 2420
Zinc Plating ASTM B 633
Zinc Plating QQ-Z-325
Zinc Plating Other
Painting & Dry Film Coatings MIL-L-46010
Painting & Dry Film Coatings MIL-L-46147
Painting & Dry Film Coatings MIL-L-81329
Zincating for Plating on Aluminum
AC7108/1 Rev A - Nadcap Audit Criteria for Painting & Dry Film Coatings (1)
Painting & Dry Film Coatings MIL-PRF-46010
Painting & Dry Film Coatings MIL-PRF-46147c
Painting & Dry Film Coatings MIL-PRF-81329
Painting & Dry Film Coatings Paint-Other
TESTING PERFORMED INTERNALLY IN SUPPORT OF CHEMICAL PROCESSING IN THE SCOPE OF THE AUDIT. (DO NOT CHECK TESTS THAT ARE OUTSOURCED.)
Process Specification
ApplicabilityYes Can Be Done No Remarks
Adhesion Tape Testing FED-STD-141Adhesion Scratch and Chisel TestingAdhesion Bend Testing (Metallic Coatings)Coating Weight Testing ANSI/ASTM B 137Conductivity TestingResistivity Testing
Light Fastness Resistance ASTM G 23/ASTM D 822/ASTM G 26Abrasion Resistance FED-STD-141SolderabilityAdhesion Testing Heat and QuenchPorosityOther Test MethodMicrohardness TestingCorrosion/Salt Spray Testing ASTM B 117Water Immersion/High Humidity TestingHeat Resistance TestingAdhesion/Wear TestingTaber Wear TestingSolution Analysis
Thickness Verification of Magnetic, Eddy Current and XRF Machines
ASTM B 244, Method 520 of FED-STD-151
Moog RequirementsEtch Inspection (NDT) AMS2649 This specification establishes the requirements for etch inspection of bare high strength low alloy steel parts having tensile strength of 180 ksi (1241 MPa) and higher and of carburized parts to detect overheating caused by abusive machining or grinding in the heat treated condition, and to detect localized discontinuous carburization. This process is not applicable to surface hardened steels produced by nitriding or carbonitriding. This process may remove 0.0001 to 0.0005 inch (2.5 to 12.7 micrometers) from the surface of the part.
Temper (Nital) Etch Inspection (NDT)
This specification establishes the requirements for etch inspection of bare high strength low alloy steel parts having tensile strength of 180 ksi (1241 MPa) and higher and of carburized parts to detect overheating caused by abusive machining or grinding in the heat treated condition, and to detect localized discontinuous carburization. This process is not applicable to surface hardened steels produced by nitriding or carbonitriding. This process may remove 0.0001 to 0.0005 inch (2.5 to 12.7 micrometers) from the surface of the part.
This specification establishes the requirements for etch inspection of bare high strength low alloy steel parts having tensile strength of 180 ksi (1241 MPa) and higher and of carburized parts to detect overheating caused by abusive machining or grinding in the heat treated condition, and to detect localized discontinuous carburization. This process is not applicable to surface hardened steels produced by nitriding or carbonitriding. This process may remove 0.0001 to 0.0005 inch (2.5 to 12.7 micrometers) from the surface of the part.
This specification establishes the requirements for etch inspection of bare high strength low alloy steel parts having tensile strength of 180 ksi (1241 MPa) and higher and of carburized parts to detect overheating caused by abusive machining or grinding in the heat treated condition, and to detect localized discontinuous carburization. This process is not applicable to surface hardened steels produced by nitriding or carbonitriding. This process may remove 0.0001 to 0.0005 inch (2.5 to 12.7 micrometers) from the surface of the part.