cielo xl family english assembly instructions - pablo designs

pg. 1

CIELO XL FAMILY

ASSEMBLY & INSTALLATION INSTRUCTIONS

TABLE OF CONTENTS

pg. 2-4......................................CIELO XL PENDANT

pg. 5-20...............................CIELO XL MULTI-LIGHT

pg. 2


[email protected] MARIN STREET

SAN FRANCISCO, CA94124

PABLODESIGNS.COM

CIELO XL

pg. 4pg. 3

CIELING MOUNTASSEMBLY INSTRUCTIONS

ADJUSTMENTASSEMBLY INSTRUCTIONS

CIELO XL CIELO XL1. WIRE LAMP TO JUNCTION BOX/ BUILDING

US: BLACK TO BLACK AND WHITE TO WHITEEU: BLUE TO BLACK AND BROWN TO RED

2. ATTACH MOUNTING PLATE TO JUNCTION BOX3. SCREW CANOPY TO MOUNTING PLATE4. TO ADJUST LAMP HEIGHT: PUSH DOWN ON SILVER

CABLE LOCK AND PUSH OR PULL CORD INTO LAMP. EXTRA CABLE COILS INSIDE OF LAMP

IMPORTANT: WE RECOMMEND CEILING MOUNTINGBE INSTALLED BY AN ELECTRICIAN

CABLE LOCK

NOTE: CORD DOES NOT REQUIRE FEILD CUTTING. CANOPYSTRAIN RELIEF DOES NOT NEED ADJUSTMENT.

COVER

BULB TYPELED FLAT PANELFULL RANGE LIGHT CONTROL VIA 120V DIMMER (US) OR ELV DIMMER (EU)

BULB REPLACEMENTCONTACT MANUFACTURER FOR BULB REPLACEMENT

LENGTH OF CORD SUPPLIED10FT (305CM)

CAREWHIPE WITH A CLEAN, DAMP CLOTH.

2

3

4

21

MOUNTING PLATE

E.U.

pg. 5

MULTI-LIGHTCANOPY

9” and 12”BOLA DISC/FELT PENDANT & CIELO XL PENDANT


pg. 7pg. 6

MULTI-LIGHT CANOPYMULTI-LIGHT CANOPYLOCATE BUILDING POWER FEED/JUNCTION BOX DETERMINE AND MARK SWAG LOCATIONS REFERENCING THE DIAGRAM AND PROVIDED CHART. PROVIDED LAMP WIRES ARE 10’, LAMP HANG HEIGHT REDUCES IN RELATION TO SWAG DISTANCE FROM CANOPY.

PROVIDED LAMP WIRES ARE 8’, LAMP HANG HEIGHT REDUCES IN RELATION TO SWAG DISTANCE FROM CANOPY. IF X=5’, Y CAN BE A MAXIMUM OF 3’.

1

2

BOLA DISC 12 BOLA DISC 18 BOLA DISC 22 BOLA DISC 32

BOLA DISC 12 5”12.7 CM

8”20.3 CM

9”23 CM

13”33 CM

BOLA DISC 18 8”20.3 CM

8”20.3 CM

9”23 CM

13”33 CM

BOLA DISC 22 9”23 CM

9”23 CM

9”23 CM

13”33 CM

BOLA DISC 32 13”33 CM

13”33 CM

13”33 CM

13”33 CM

SWAG SPACINGCENTER TO CENTER

Y

xJUNCTION BOXANSCHLUSSDOSEBOÎTE DE JONCTIONCAJA DE CONEXIÓNSCATOLA DI GIUNZIONE

EN: DE: FR: ES: IT:

NOTE: DISC COMES WRAPPED IN PROTECTIVE SLEEVE. LEAVE SLEEVE ATTACHED UNTIL LAMP IS FULLY ASSEMBLED

REMOVE CANOPY COVER, SET ASIDE

REMOVE DRIVER PLATE BY REMOVING 3X FLAT HEAD SCREWS

3

4

pg. 9pg. 8

MULTI-LIGHT CANOPYMULTI-LIGHT CANOPY5

6

ROUTE BUILDING WIRING THROUGH MOUNTING PLATE.

ATTACH PLATE TO JUNCTION BOX WITH 8-32 MACHINE SCREWS (NOT PROVIDED) OR APPROPRIATE ANCHORS.

WIRE BUILDING WIRING TO TERMINAL BLOCK. US: BLACK TO BLACK AND WHITE TO WHITE EU: BLUE TO WHITE BROWN TO BLACK.

L/BLACK

N/WHITE

7

REMOVE THREADED SWAG CAPMOUNT SWAG USING APPROPRIATE FASTENER AND ANCHOR IN MARKED LOCATION

Swag

Fastener (not provided)

NOTE: Cable slot should face canopy center point.

Canopy

Swag

Cable slot

*

8 9

pg. 11pg. 10

MULTI-LIGHT CANOPYMULTI-LIGHT CANOPY

PLACE WIRE IN SWAG. MAKE SURE WIRE IS IN CHANNEL

THREAD SWAG CAP INTO SWAG TO SECURE LAMP.THIS STEP IS WHERE YOU DETERMINE YOUR LAMP HANG HEIGHT

BOLA: ASSEMBLE DISC AND LIGHT ENGINE

A

B

BOLA

BOLA

CIELO XL

x

10

11

USE PROVIDED GLOVES WHEN HANDLING LAMPTO AVOID FINGER MARKS.

* THREAD WIRE THROUGH MOUNT PLATE

PULL WIRE TAUGHT AND STRAIN RELIEVE

12

13

pg. 13pg. 12


D

E

F

REMOVE PLUG

THREAD WIRE THROUGH

CANOPY AND CENTER OF

DRIVER PLATE

A

B C

A13

PLACE CANOPY COVER BAG OVER

CANOPYUSING A PENCIL, PUNCTURE SMALL

HOLE FOR WIRE TO PASS THROUGH

STRAIN RELIEVE WIRE ON DRIVER PLATE

NOTE FOR BOLA: THIS IS WHEN YOU SET

YOUR HANG HEIGHT

TIE KNOT JUST PAST STRAIN RELIEF

REMOVE INDIVIDUAL LAMP DRIVERS FROM INDIVIDUAL LAMP CANOPIES

ATTACH DRIVER PLATE TO MOUNT PLATE WITH PROVIDED FLAT HEAD SCREWS

THREAD WIRES THROUGH CENTER OF DRIVER PLATE

A

B

BOLA CIELO XL

14

15

pg. 15pg. 14


ATTACH DRIVERS TO DRIVER PLATE

PEEL LINER OFF OF VHB TAPE16

17

CONNECT DRIVERS TO TERMINAL BLOCK.

US: BLACK TO BLACK AND WHITE TO WHITE EU: BLUE TO BLUE AN BROWN TO BROWN

CONNECT DRIVERS TO TERMINAL BLOCK.

US: BLACK TO BLACK AND WHITE TO WHITE EU: BLUE TO BLUE AN BROWN TO BROWN

l/BLACK

N/WHITE

BOLA

l/BLACK

N/WHITE

CIELO XL

18

18

CIELO XLBOLA

9” CANOPYMAXIMUMCAPACITY

12” CANOPYMAXIMUMCAPACITY

pg. 17pg. 16


BOLA

CIELO XL

l/BLACK

N/WHITE

l/BLACK

N/WHITE

19

19

*

*

!

ONE AT A TIME, WIRE LAMPS TO MATCHING DRIVERS. CUT EXCESS WIRE IF NECESSARY

ONE AT A TIME, WIRE LAMPS TO MATCHING DRIVERS. NO FIELD CUTTING OF WIRES IS

REQUIRED. DO NOT CUT.

FOLLOW LAMP AND WIRE

LABELS IF PRESENT

IF USING 0-10V DIMMING, WIRE

DIMMING IN PARALLEL

ATTACH CANOPY COVER

CARE INSTRUCTIONSWIPE CLEAN WITH A SOFT DAMP CLOTH. AVOID AMMONIA BASED CLEANER.

20


pg. 19


pg. pg. 18



BOLA CIELO XL

CABLE LOCK

ADJUSTMENTEINSTELLUNGAJUSTEMENTAJUSTEREGOLAZIONE

EN: DE: FR: ES: IT:

CIELO XL - ADJUST HEIGHT OF LAMPS AS NECESSARY


BOLA - THREAD GLOBE ONTO HEAT SINK


21 21

pg. 20

MULTI-LIGHTCANOPY

9” and 12”

[email protected]@PABLODESIGNS.EU

888 MARIN STREETSAN FRANCISCO, CA

94124

PABLODESIGNS.COMPABLODESIGNS.EU

cielo xl family english assembly instructions - pablo designs

Documents