circuit lab therm is to rs
TRANSCRIPT
Pat Arnott, ATMS 360 Atmospheric Instrumentation
ThermistorsTHERMal resISTORS
Pat Arnott, ATMS 360 Atmospheric Instrumentation
ThermistorsTHERMal resISTORS
A thermistor is a type of resistor used to measure temperature changes, relying on the change in its resistance
with changing temperature. ****** Thermistor is a combination of the words thermal and resistor. The
Thermistor was invented by Samuel Ruben in 1930, and has U.S. Patent #2,021,491.
Leads, coated Glass encased Surface mount
Pat Arnott, ATMS 360 Atmospheric Instrumentation
ThermistorsTHERMal resISTORS
Thermistors are made of semiconductor materials (metallic compounds including oxides such as manganese, copper, cobalt, and nickel, as well as single-crystal
semiconductors silicon and germanium).
Contrast <<--->> Common carbon resistors, made from carbon powder mixed with a phenolic binder
glue.
Leads, coated Glass encased Surface mount
Pat Arnott, ATMS 360 Atmospheric Instrumentation
ThermistorsTHERMal resISTORS
Assume a simple linear relationship between resistance and temperature for the following discussion:
ΔR = k ΔT
where
ΔR = change in resistance ΔT = change in temperature
k = first-order temperature coefficient of resistance
Source: http://en.wikipedia.org/wiki/Thermistor
Pat Arnott, ATMS 360 Atmospheric Instrumentation
ThermistorsTHERMal resISTORS
Thermistors can be classified into two types depending on the sign of k.
If k is positive, the resistance increases with increasing temperature, and the device is called a positive temperature coefficient (PTC) thermistor, Posistor.
If k is negative, the resistance decreases with increasing temperature, and the device is called a negative temperature coefficient (NTC) thermistor.
Source: http://en.wikipedia.org/wiki/Thermistor
Pat Arnott, ATMS 360 Atmospheric Instrumentation
ThermistorsTHERMal resISTORS
Resistors that are not thermistors are designed to have the smallest possible k, so that their resistance remains almost constant over a wide temperature range.
Source: http://en.wikipedia.org/wiki/Thermistor
Pat Arnott, ATMS 360 Atmospheric Instrumentation
ThermistorsTHERMal resISTORS
Source: http://www.science.uwaterloo.ca/~jddmarti/p352_w2007/Thermistor_50K.pdf
Thermistor-choice is based on the nominal resistance you want at the operating temperature range, on the size, and on the time constant.
Time constants are about 5 - 10 seconds. (Check this out with your thermistor).
Pat Arnott, ATMS 360 Atmospheric Instrumentation
ThermistorsTHERMal resISTORS
Source: http://www.science.uwaterloo.ca/~jddmarti/p352_w2007/Thermistor_50K.pdf
Pat Arnott, ATMS 360 Atmospheric Instrumentation
ThermistorsTHERMal resISTORS
Example Applications:1. Temperature measurement.
2. Time delay (self heating from large current ‘opens’ the thermistor so it can be used as a slow switch). Heating = i2 R where R is the resistance and i is the current.
3. Surge suppression when a circuit is first energized. Current needs to flow through the thermistor for awhile to heat it so that it ‘opens’, and acts again as a switch.
Pat Arnott, ATMS 360 Atmospheric Instrumentation
Demonstration
Pat Arnott, ATMS 360 Atmospheric Instrumentation
Demonstration
Pat Arnott, ATMS 360 Atmospheric Instrumentation
Demonstration
Pat Arnott, ATMS 360 Atmospheric Instrumentation
Demonstration