ANNEXURE - X

Schedule of Rates - Pune - Retail RO

SR. NO. ITEM DESCRIPTION UNIT RATE

1 SITE CLEARANCE SM 5.6Surface dressing of the ground including removing small plants, bushes,vegetation and making surface levelled and disposal of rubbish outsideHPCL's premises to an unobjectionable place, as directed by the Engineer inCharge.

2 EXCAVATION IN EARTH UPTO 3 MET M3 115Excavation for foundation upto required depth below existing ground level up to3 m. depth in any type of soil except hard rock . Rate to include dressing thesides and bottom, bailing out of water if encountered, shoring, strutting,backfilling after the construction of foundation, compacting by the side of thefoundation and disposal of surplus excavated earth within/outside HPCL'spremises to an unobjectionable place, as directed by the Engineer in Chargeincluding spreading, watering and compaction, complete .

3 EXCAVATION IN EARTH 3 MTO 6M M3 145Same as above but from 3 m. to reqr. Depth.

4 EXCAVATION IN HARD ROCK UPTO 3M M3 530Description same as above item except the soil will be hard rock andexcavation shall be done by chiselling/ pneumatic drilling (Blasting is probhited)

5 EXCAVATION IN HARDRK 3M-6M M3 650Same as above but from 3 m. to reqr. Depth.

6 SAND FILLING - LAYERS<150MM M3 700Supply and filling with clean silver / river sand of approved quality in layers of150 mm each including spreading, compacting by hand ramming and wateringetc, all complete as per direction of Engg.-In-Charge. Measurement basiscompacted thickness only.

7 EARTH FILLING- LAYERS<200MM M3 150Supplying and filling imported earth of approved quality in layers not exceedingcompacted thickness of 200mm incl. Watering ,ramming, compacting, and ifrequired, rolling and re-rolling with power roller / manual roller / mechanicalcompactors to achieve maximum compaction, all complete as per direction ofEngg.-In-Charge. The earth should be free from weeds, grass and otherobjectionable debris. Black Cotton soil shouldn't be used. Measurement basiscompacted thickness only. MDD and OMC tests shall be carried out and reports 8 MURRUM FILLING- LAYERS<150MM M3 275Supplying and filling imported murrum of approved quality in layers notexceeding compacted thickness of 150 mm inclusive spreading, Watering,ramming, compacting, and if required, rolling and re-rolling with power roller /manual roller / mechanical compactors to achieve maximum compaction, allcomplete as per direction of Engg.-In-Charge. The murrum should be excavatedfrom a quarry / mines, free from weeds, grass and other objectionable debris.Measurement basis compacted thickness only. MDD and OMC tests shall becarried out and reports shall be submitted to EIC.9 EARTH/MUR FILL AVAILABLE AT SITE M3 62

Page 168

Supplying and filling good quality earth/ murrum available at site in layers notexceeding compacted thickness of 200mm incl. Watering ,ramming,compacting, and if required, rolling and re-rolling with power roller / manual roller/ mechanical compactors to achieve maximum compaction, all complete as perdirection of Engg.-In-Charge. The earth should be made free from weeds, grassand other objectionable debris. Black Cotton soil shouldn't be used.Measurement basis compacted thickness only. MDD and OMC tests shall becarried out and reports shall be submitted to EIC.

10 PCC 1:4:8 M3 2240Providing and laying PCC 1:4:8 using 40 mm and down size graded stoneaggregates including machine mixing, providing formwork if required, placing,compacting by hand ramming , curing etc complete.

11 PCC 1:3:6 M3 2605Providing and laying PCC 1:3:6 using 40 mm and down size graded stoneaggregates including machine mixing, providing formwork if required, placing,compacting by hand ramming, curing etc complete.

12 PCC 1:2:4 FOR DPC SM 285Providing and laying 50 mm thick DPC in PCC 1:2:4 mix with 6 to 12 mm sizeHBG aggregate in two layers of 20 mm thick with two coats of hot bitumen(Grade A- 90/S-90 conforming to IS 73) applied at rate 1.7 Kg per sq.mtr. overeach layers as per specifications including cleaning, watering ;the top surface ofwalls, centering, shuttering, placing, tamping, curing, sprinkling each layer of dryand sharp sand over the hot bitumen etc. all complete as per drawing, Engineer-in-charge direction. 13 RCC 1:2:4 FOR COPING M3 3450Providing and laying 60 mm average thickness coping in CC 1:2:4 mix using 6 to12 mm stone aggregate with 40 mm projection on either side of wall with dripmould. Rate to include 20 mm thick plaster in cm 1:4 for fixing of glass piecesincluding mixing, providing necessary shuttering, compaction and curing.Thickness of coping at the ends shall be 40 mm and 80 mm at centre . 14 PCC 1:2:4 FOR GROUTING ANGLE M3 3254Providing and laying PCC 1:2:4 mix using 20mm to 12 mm stone aggregateincluding mixing, providing necessary shuttering, compaction and curing etccomplete.

15 RCC 1:1.5:3 FOR FOOTING M3 4287Providing , mixing and placing REINFORCEMENT CEMENT CONCRET 1:1.5:3mix with Ordinary Portland Cement using 20 mm and down size graded crushedaggregate including providing and fixing necessary plywood /steel shuttering ,scaffolding, machine mixing, compacting by vibrators, curing, hacking thesurface to receive plaster etc. complete. Rate shall be exclusive of the cost ofsteel reinforcement, which will be paid under a separate item. Concreteconforming to relevant specifications of IS 456 Latest Edn.16 RCC 1:1.5:3 FOR COLUMNS/BEAMS M3 4688 Same as above but for columns/beams

17 RCC 1:1.5:3 FOR CULVERT SLAB M3 4800 Same as above but for culver slab

18 UR PILES 350MM DIA MT 900UNDER REAMED PILES : Providing RCC 1:1.5:3 for under reamed piles upto required depth with double bulbs as per IS 2911 etc. All complete. Pile capand reinforcement steel shall be paid separately. Size 350 mm diameter

19 UR PILES 300MM DIA MT 798Same as above but size 300 mm diameter

20 UR PILES 230MM DIA MT 645

Page 169

Same as above but size 230 mm diameter21 REINFORCEMENT STEEL TM 46118

Supply ,fabrication, hoisting and placing in position HYSD reinforcement barsconforming to IS1786 -Latest Edition Grade FE 415 /TMT bars of same grade asper detailed drawing and specifications including cutting, bending, cranking andtying with 18 SWG black annealed binding wire complete. The rates shall beapplicable for all heights and depths. Payment shall be made as perreinforcement drawings and with theoretical weights only including all authorisedlaps, chairs, spacers and hooks.

22 BRICK MASONRY SUBSTRUCTURE M3 2572BRICK MASONRY WORKS :Providing and constructing following brick masonryin CM 1:5 using first quality bricks of Class designation 35 (minimum) andconforming to IS-1077-1986 including providing all openings and projections ,raking the joints to 1 cm deep, scaffolding, soaking of bricks in water prior to useand curing etc complete as per specifications . SUBSTRUCTURE: Providingand laying brick masonry as above for foundation below DPC level.23 BRICK MASONRY SUPERSTRUCTURE M3 2706Providing and laying brick Masonry as above but for superstructure above DPClevel including scaffolding.

24 PARTITION 115-BRICK MASONRY SM 370Providing & laying brick masonry as above but for 115 mm thick in partition wallsin CM 1:4. Rate to include providing 75 mm thick RCC 1:1.5:3 bands using 2 nos 8 mm dia Torsteel reinforcement at every 1 M height of wall including plywood/MS shuttering. Steel reinforcement shall be paid for separately.

25 BRICK MASON WITH USED BRICKS M3 1344Providing and constructing brick masonry in CM 1:5 using used bricks. Thebricks should be get approved from the engineer in charge & should be cleanedfrom all dust & dirt prior to use. The item includs providing all openings andprojections , raking the joints to 1 cm deep, scaffolding, soaking of bricks inwater prior to use and curing etc complete as per specifications .

26 RRM SUBSTRUCTURE M3 1719Providing and constructing random rubble masonry with good quality stone in CM 1:5 for substructure & superstructure as per IS 1597 part 1, latest edition. Rate to include soaking stones, raking the joints to 1 cm deep and curing complete. One Through / Bond stone shall be provided for every square meter of facing , evenly distributed in a staggered pattern. They shall have about 0.03 sqm in face area and shall have a tailing for the full width of masonry upto 600mm.If masonry wall is over 600mm thick, a line of headers (not less than 450mm length) overlapping each other by 150mm shall be laid. Bond stones shall be distinctly marked on its face during construction for verification. Quoin/key/corner stone shall not be less than 0.03 cum in volume.

27 RRM SUPER STRUCTURE M3 1800Same as above item but FOR SUPERSTRUCTURE including scaffolding

28 RUBBLE SOLLING 230 MM THK SM 156Providing 230 mm thick rubble pitching including surface dressing, makingrequired slope . Rate to exclude flush pointing which will be paid for separately.

29 RUBBLE SOLLING – 150 MM THICK SM 130

Page 170

Same as above item but for 150 mm thick 30 FLUSH POINTING SM 63

Providing flush pointing in rubble pitching with 1:3 cement mortar includingcuring etc. complete.31 RAISED POINTING SM 73Providing raised pointing 12 mm with CM 1:3 along the joints of exposed stonemasonry. The joints shall be raked & cleaned, curing etc. all complete.

32 SUNKEN POINTING 12 MM SM 95Providing sunken pointing 12 mm wide & 5 mm deep with CM 1:3 along thejoints of exposed stone masonry. The joints shall be raked & cleaned, curing etc.all complete.

33 CEILING PLASTERING 6 MM THK SM 105SMOOTH CEMENT PLASTER FOR CEILING/CHHAJA Providing and applying6 mm thick plaster in CM 1:3 to ceiling and bottom surface of chajja usingscreened sand including finishing smooth and providing drip moulds at chajjaedges, scaffolding and curing etc. complete.34 SMOOTH PLASTERING 15MM THK FOR INT. WALL SM 127Providing and laying 15mm thick smooth cement plastering in 1:4 CM in singlecoat to all the interior walls including providing necessary scaffolding, chickenwire mesh at all joints of brick and concrete surfaces, with a minimum overlapof 150 mm in all directions and additional thickness if required to achieve perfectline and level without any extra cost. 35 PLASTERING 20MM THK SM 159Providing and laying average 20 mm thick sand faced cement plaster as perfollowing procedure : Apply 12 mm thick coat of CM 1:4 mixed with CICO/IMPERMO/ ACCOPROOF water proofing compound mixed as permanufacturer's specifications as 1st coat and leaving the surface rough. Apply2nd coat of 8 mm thick of CM 1:4 and finishing the surface by rubbing withsponge till uniform texture is obtained. Rate shall include providing necessaryscaffolding, chicken wire mesh.36 WEEP HOLES MT 215Providing, fabricating and installing in place, 75 mm dia PVC Pipes of variouslengths & at places as directed at site on the masonry wall for water drainage.

37 ST. STEEL - CLF/BWF TM 57000STRUCTURAL STEEL: ANGLE IRON POST : Supply, fabrication , erection andgrouting of 65 x 65 x 6 ISA post and supporting angles of specified length in1:2:4 concrete grout at every 2.4 m C-C or as advised. Rate to includefabrication of the post as per the specification, erecting, placing, grouting andpainting of the posts with two coats of Synthetic Enamel over two coats of ZincPhosphate Primer Paints and primer shall be of SHALIMAR/ BERGER/ASIANMake first quality only. 38 PIPE RAILING - CLF/BWF MT 370PIPE RAILING : Supply and fixing of 40 NB medium quality MS pipes(IS 1239latest edition) for top and bottom railings to angle iron posts for fixing the edgesof the chain link fencing. Rate includes fabn, cutting, bending of the MS pipe,supply and fixing of MS clamps at every post, with nuts and bolts(all propersized) and painting the railing with two coats of Zinc Phosphate Primer and twocoats of Synthetic enamel paint after proper cleaning /scrapping .SHALIMAR/BERGER/ASIAN make 1st quality only.39 CHAIN LINK FENCING SM 275

Page 171

CHAIN LINK FENCING : Supply and fixing of 50 x 50mm opening size 10 SWGGI chain link fencing to the angle iron post with 8 SWG GI hooks and nuts andrailing with 14 SWG GI continuous wire (all details shall be as per encloseddrawing ) up to a height of 1.8 m from the ground level. Rate to include unrollingthe bundle, erecting, tightening and fixing at 300 mm C-C on the vertical portionof the posts to every top and bottom railing with 14 gauge MS wire. 40 BARBED WIRE FENCING MT 215BARBED WIRE FENCING Providing and fixing 13 rows horizontal and twodiagonals with two ply 12 SWG GI barbed wire fencing with barbes @ 100mmc/c . Angle iron post shall be paid separately. For payment purposemeasurement shall be taken for the lenth of plot boundary . No measurementshall be taken for 13 rows individually.41 HUME PIPES- 1000 MM DIA MT 4760HUME PIPE- Supplying, laying, joining and aligning 1000mm DIA NP3 classRCC Hume pipes conforming to IS-458 Latest Edition below approach road asdirected. Rate to include joining with cement mortar, excavation up to requireddepth and providing and laying PCC 1:2:4 haunching @ 1m c/c , also includingcutting, bending & supply and laying of 17 SWG annealed binding wire inside theHUME Pipe for pulling cables in future.Test certificates from manufacture shallbe submitted and approved by EIC before use.1000 MM DIA

42 HUME PIPES- 900 MM DIA MT 4300Same as above but size 900 mm dia

43 HUME PIPES- 600 MM DIA MT 3148Same as above but size 600 mm dia

44 HUME PIPES- 450 MM DIA MT 2300Same as above but size 450 mm dia

45 HUME PIPES- 300 MM DIA MT 750Same as above but size 300 mm dia

46 HUME PIPES- 250 MM DIA MT 600Same as above but size 250 mm dia

47 HUME PIPES- 200 MM DIA NP2 CLASS MT 500Same as above but NP2 class & size 200 mm dia

48 HUME PIPES- 150 MM DIA NP2 CLASS MT 400Same as above but NP2 class & size 150 mm dia

49 ANTI TERMITE TREATMENT SM 77ANTI TERMITE TREATMENT Providing anti-termite treatment including dilutingand injecting chemical solution/ Neem base solution and creating a continuousbarrier under and alround the column pits, wall trenches, basement excavation,top surface of plinth filing, junction of wall and floor, along the external perimeterof building, expansion joints, over the top surface of consolidated earth on whichapron is to be laid, surroundings of pipes and conduits etc. Complete as perspecification using Clorpyriphous emulsified cocentrate (20%) in 1%concentration ( or as recommended by the manufacturer) or using Neem basedsolution.

50 WHITE RECTIFIED TILES FOR COMP SM 900Providing and fixing 1'x2' white color rectified tiles (approved shade and make) of First quality , free from crack fissures & flakes with straight edge s & perfectcorners fixed at right angles as per the design and pattern, incldg. applying8mm thick backing plaster in 1:4 CM and fixing the tiles with neatcement paste,finishing the joints with white cement to match the colour of tiles properly cured& finished in all respects etc. complete.

Page 172

51 CERAMIC TILE FLOORING 400mmX400mm SM 662CERAMIC TILE FLOORING: Providing and laying (NITCO/KAJARIA/BELL/H&R JOHNSON MAKE)matt finish 1st quality Ceramic tiles of 6/8 mm thick offollowing size in flooring of approved make and shade and free from cracks,warpage,fissures and flakes with straight edges and perfect corner laid at rightangle as per design and pattern over a bedding of cement mortan of 30 mmthick CM 1:5 finishing the joints neatly with white cement mixed with matchingcolour pigment and finish in all respect and all material and labour complete.Size 400mm X 400 mm

52 CERAMIC TILE FLOORING 300mmX300mm SM 605Same as above but size 300mmX300mm

53 VITRIFIED TILE FLRG. 400mmX400mm SM 1300POLISHED VITRIFIED TILE FLOORING :Providing and laying 1st quality(NITCO/KAJARIA/BELL/H&R JOHNSON MAKE)polished vitrified tiles of 8 mmthick of followg.sizes on flooring (approved make&shade, free from cracks,warpage,fissures and flakes, straight edges and perfect corner) laid at rightangle as per design and pattern over a 30mm bedding of cement mortar(CM1:5), finishing the joints neatly with white cement mixed with matching colourpigment and finish in all respect and all material and labour complete.

54 VITRIFIED TILE FLRG. 300mmX300mm SM 1000Same as above but size 300mmX300mm

55 VITR.TILE 600X600SALT PAPER GRAY SM 1570Providing and laying 1st quality polished vitrified tiles of 8 mm thick 600X600size in flooring of approved make and shade and free from cracks,warpage,fissures and flakes with straight edges and perfect corner laid at rightangle as per design and pattern over a bedding of cement mortan of 30 mmthick CM 1:5 finishing the joints neatly with white cement mixed with matchingcolour pigment and finish in all respect H&R JOHNSON( Marbonite) makeSALT PEPPER GRAY FINISH , SIZE: 600 X 600 mm or approved equivalentfrom NITCO.and all material and labour complete as per the direction of 56 VITRIFIED TILE 600X600 SINTRA SM 1570Same as above but H&R JOHNSON( Marbonite) make SINTRA FINISH orapproved equivalent from NITCO

57 VITRFIED SNOW CARARA 3'X3' (900x900) SM 1931Same as above but size 900mmX900mm & H&R JOHNSON( Marbonite) makeSNOW CARARA FINISH or approved equivalent from NITCO

58 VITRIFIED OLYMPUS 600X600 SM 1450Same as above but size 600mm X 600 mm &H&R JOHNSON( Marbonite) makeOLYMPUS finish or approved equivalent from NITCO.

59 VITRFIED SAVONA -600X600 SM 1450Same as above but size 600mmX600mm & NITCO make SAVONA finish orapproved equivalent from H&R JOHNSON.

60 VITRIFIED OCEAN MIST-1000X1000 SM 1931Same as above but size 1000mmX1000mm & NITCO make OCEAN MISTFinish or approved equivalent from H&R JOHNSON

61 VITRIFIED NOVARA BIEGE-800X800 SM 1850Same as above but size 800mmX800mm & NITCO make NOVARA BIEGEfinish or approved equivalent from H&R JOHNSON

62 CERAMIC TILE CREAMA ROYAL SM 780

Page 173

Providing and fixing ceramic tiles of 300 x 600 mm size & 5 mm thick CREMAROYAL From HR JOHNSON Only) ) First quality , free from crack fissures &flakes with straight edge s & perfect corners fixed at right angles as per thedesign and pattern, incldg. applying 12mm thick backing plaster in 1:4 CM andfixing the tiles with neatcement paste, finishing the joints with white cementmixed with colouring pigments to match the colour of tiles properly cured &finished in all respects etc. complete.63 CERAMIC TILE RIVIERA SM 780Same as above but Riviera finish from NITCO

64 TERRACOTTA TILES SM 750Terracotta Tiles:Providing and fixing terracotta tiles minimum 3 mm thick andminimum 75x150 mm size of approved shade and make First quality , freefrom crack fissures & flakes with straight edges & perfect corners fixed in trueline & level as per the design and pattern advised by Engg.-In-Charge. Rateincludes applying 12 mm thick backing plaster in 1:3 CM in true line & level,properly cured & rough finished. Fixing the tiles with neat cement paste andfinishing the joints with terracotta paint in a neat & aesthetic way complete in allrespects. Approved Make of Tiles: Dazzle Designer Tiles of Milan - Terracottasmooth finish

65 MANGLORE TILES ON ROOF/CHAJJA SM 750Providing and fixing Mangalore tilesof 12 mm thick and minimum 230x150 mmsize of approved shade and make First quality , free from crack fissures &flakes with straight edges & perfect corners fixed in true line & level as per thedesign and pattern advised by Engg.-In-Charge and finishing the work in a neat& aesthetic way complete in all respects. Rate to include Teakwood framingstructure for holding the tiles in fixed condition.66 MOSAIC TILES OF NITCO SM 1017MOSAIC TILES FROM NITCO: Supply and fixing mosaic tiles of NITCO makeRY36S and GY 36S in pattern including providing 1:5 CM bed and floating coatof neat cement slurry finishing the joints with white cement , mixed withmatchinmg colour pigments, cleaning the surface with dilute sulfuric acid etccomplete.

67 MOSAIC TILES OF LOCAL MAKE SM 550Supply and fixing mosaic tiles of local make similar to Nitco-RY36S and GY 36Sin pattern including providing 1:5 CM bed and floating coat of neat cement slurryfinishing the joints with white cement , mixed with matchinmg colour pigments,cleaning the surface with dilute sulfuric acid etc complete.

68 GRANITE TILE FLOORING SM 1550GRANITE TILE FLOORING Providing and laying 10 mm thick granite tile ofsize of 300 mm x 300 mm in flooring of approved shade and free fromcracks, warpage,fissures and flakes with straight edges and perfect corner laidat right angle as per design and pattern over a bedding of 30 mm thick 1:5cement mortar and neat cement slurry, finishing the joints neatly with whitecement mixed with matching colour pigment and finish in all respect and al lmaterial and labour complete.

69 IPS FLOORING SM 209IPS FLOORING Providing mixing and laying 50 mm thick Indian Patent Stoneflooring in PCC 1:2:4 mix concrete with 12 mm and down size graded crushedaggregate including providing and fixing 4 x 25 mm size glass strips in 1 metrex 1 metre panels, casting the concrete compacting and finishing the surfacesmooth using cement slurry.

70 GRANITE SKIRTING MT 180

Page 174

GRANITE SKIRTING Providing and fixing 10mm thick jet black graniteskirting of 100 mm hight free from crack fissures & flakes with straight edges &perfect corners fixed at right angles with neat cement paste and finishing thejoint with white cement mixed with matching colour pigment .

71 CERMIC TILE DADO SM 630CERAMIC TILES DADO IN TOILET: Providing and fixing ceramic tiles of 300 x200 mm size (approved shade and make )First quality , free from crack fissures& flakes with straight edge s & perfect corners fixed at right angles as per thedesign and pattern, incldg. applying 12mm thick backing plaster in 1:4 CM andfixing the tiles with neatcement paste, finishing the joints with white cementmixed with colouring pigments to match the colour of tiles properly cured &finished in all respects etc. complete.72 BORDER TILE SM 700Same as above but laying and fixing designed border tile.

73 GRANITE SLAB 18 MM BLACK COLOUR SM 288818MM THICK GRANITE CLADDING FOR CURTAIN WALL Providing andfixing machine cut and polished black Granite slab of thickness of 18 mmselected & sorted for uniformity in colour, free from cracks, fissures and flakeswith straight edges and perfect cornors using 50mmx20mmx3mm SS T shapedcleats of 100mm long . The cleats are fixed over the wall with M12x100mm longGI fasteners by providing 2 nos 12mmx25mm size slots and drilling the wall.Rate to include making necessary grooves in granite slab.74 HP LOGO FIXING EA 900Fixing of HPCL Logo Box in line and level on the Granite curtain wall with thehelp of necessary fasteners.

75 KOTA STONE FLOORING SM 775KOTA STONE FLOORING Providing and laying 20mm thick Kota Stoneflooring using machine cut and machine polished tiles of uniform colour andapproved size and pattern including bedding of 30mm thick CM1:3 close jointedand floated with matching cement slurry laid to level as required, curing machinepolishing with oxalic acid to achive mirror finish etc., complete.76 KOTA STONE SKIRTING MT 130KOTA STONE SKIRING Providing and laying 125mm high x 18mm thick Kotastone skiring on the walls in uniform colour and approved size & patternincluding bedding of 20mm thick CM1:3 close jointed & floated with matchingcement slurry, curing, polishing to mirror finish with oxalic acid etc., complete.

77 KOTA STONE STEPS SM 800KOTA STONE STEPS Providing and fixing 20 mm thick one piece Kota stoneslabs with 25mm bedding CM 1:3, cement slurry and machine polishing on oneside for risers of steps, treads and shelf slab including nosing etc . complete

78 GRANITE SILL SLAB FOR WINDOWS SM 2617SILL SLAB Providing and laying 18 mm thick machine cut & machine polishedjet black granite strips over a bedding of 18 mm thick 1:5 CM for window sills.The strips shall be of single piece only as per width of window wall and project12 mm beyond the face of the wall.79 EUROCON TILE-WALKWAY NLT 500 SM 1050Supply and fixing concrete tile of EUROCON make of approved shade of20mm thickness for flooring including providing 20mm thick 1:5 cement mortarbed and a floating coat of neat cement slurry, finishing the joints with whitecement mixed with matching colour pigment, cleaning the surface with dilutesulphuric acid etc. Complete. If necessary, surface unevenness shall be filledup with brick ballast manually compacted with watering etc. complete as perinstructions of Engg.-In-Charge without extra cost. Basic rate : Not lower than

Page 175

80 EUROCON TILE-WALKWAY NLT 400 SM 950Same as above item but for treads and risers Basic rate: Not lower than Rs.400/sqm

81 WATER PROOFING BY BITUMEN FELT SM 363Water proofing with bitumen felts as per specifications (Bitumen of Shalimar orequivalent make as approved by EIC)- Scrapping, removing old bituminisedsurface, if any, by chisel, etc, cleaning the surface thoroughly with wire brushand duster and providing water proofing as per specification. Applying one coatof bitumen primer, applying hot bitumen 30/40 @ 1.2kg/SQM. Supplying andlaying bitumen felt conforming to IS:1322 in lengths at right angles to thedirection of the run of the gradient, starting at the lowest level and overlap of75mmfor adjacent layers, overlap at end of strip of felt should be 100mm.Parapet joints to be suitably fillated and the feltto to be taken upto a minimumheuight of 225mm on the parapet. Scope of job includes breaking of parapetplaster upto min 225mm making chases before the felto and finally plastering 82 BRICKBAT TERRACE WATER PROOF. SM 370BRICKBAT COBA ON TERRACE Providing and laying integral cement basedwater proofing of average 100 mm thick as per specifications given. The jobincludes Cleaning of RCC slab and applying neat cement slurry mixed withwaterproofing compound, providing and laying brickbat coba in CM 1:4 mixedwith water proofing compound and curing for a period of 24 hours, laying of 25mm thick PCC 1:1.5:3 mix with 6 mm and down size coarse aggregate andwater proofing compound, finishing smooth, making half round vata at thejunction of parapet wall and slab and curing for 10 days. NOTE:- Contractor tosubmit a guarantee in respect of performance of waterproofing ,for 10 years ona Stamp-paper. Further , @10% of job amount shall be retained for 2 years asretention money , returnable after retention period without interest . Approvedbrands of waterproofing compound are : CICO/ACCOPROOF/IMPERMO.

83 CHAJJA WATER PROOFING SM 240Water proofing on top of chhaja with 25mm thick PCC 1:1.5:3 with 6mm anddown size stone aggregate mixed with water proofing compound, finishingsmooth, making half round vata at the junction of chhaja and wall , curing etc.complete.

84 WHITE WASH SM 12All material required for execution of painting work shall be obtained direct fromapproved manufacturers and shall be brought to the sites in their drums / cans /bags etc with seals unbroken. No thinner shall be used unless approved byEngg.-In-Charge. The paint shall be applied by using brush, roller or spraying asdirected. The paint etc shall be applied only after proper surface preparation byremoving all dirt, dust, mortar droppings, another foreign matter, loose scale byusing brooms, wire brush, sand paper etc as per requirement and directioncomplete. All holes, cracks, patches etc shall be made good with material similarto that of the surface. The painting shall be applied in specified coats or moreso as to obtain the desired finish. If additional coats are required to obtainuniform and smooth finish, the same shall be carried out at no extra cost. Thejob includes provision of scaffolding using safety precautions, curing etc as WHITEWASH Providing and applying 3 coats of white wash to plastered andconcrete surfaces including providing necessary scaffolding, surfacepreparation , mixing DDL binder, blue etc. complete as per IS: 712- LatestEdition. If additional coats are required to obtain uniform and smooth finish, thesame shall be carried out at no extra cost.85 OIL BOUND DISTEMBER SM 49

Page 176

OIL BOUND DISTEMPER Providing and applying 2 coats ( first coat with brushand final coat with Roller) of OBD of approved make and shade on all surfacesand heights to give an even shade including primimg coat and full putty afterthoroughly brushing the surface free from mortar dropping and other foreignmatter and also including preparing the surface even and sand papered smoothetc., all material and labour complete. General specifications/guidelines givenunder WHITEWASH item also to be followed, as applicable.

86 ACRYLIC EMULSIONPAINT(INT/GRD) SM 88ACRYLIC EMULSION PAINT (INTERIOR GRADE) Providing and applying 2coats ( first coat with brush and final coat with Roller) of Acrylic Emulsion paint ofapproved make and shade on all surfaces and heights to give an even shadeincluding primer and full putty after thoroughly brushing the surface free frommortar dropping and other foreign matter and also including preparing thesurface even and sand papered smooth etc., all material and labour complete.General specifications/guidelines given under WHITEWASH item also to befollowed, as applicable.87 ACRYLIC EMULSIONPAINT(EXT/GRD) SM 95ACRYLIC EMULSION PAINT (EXTERIOR GRADE) Providing and applying 3coats of acrylic anti fungal cement paint including primer of BERGER(Weathercoat) or approved equivalent make and shade to all the exteriorsurfaces as per manufacturer's specifications including providing necessaryscaffolding, curing , etc. complete. If additional coats are required to obtainuniform finish, the same shall be carried out at no extra,cost as directed byEngineer In Charge. General specifications/guidelines given under 88 APEX PAINTING SM 105APEX PAINTING : Providing and applying 2 coats of Apex paint to all theexterior surfaces including a coat of primer as per manufacturer's specificationcomplete. General specifications/guidelines given under WHITEWASH item alsoto be followed, as applicable.

89 PLASTIC EMULSION PAINT SM 85PLASTIC EMULSION PAINT: Providing and applying 2 coats ( first coat withbrush and final coat with Roller) of Plastic Emulsion paint of approved makeand shade on all surfaces and heights to give an even shade including primerand compatible putty. Approved Make: Asian/Nitco / Nerolac. Generalspecifications/guidelines given under WHITEWASH item also to be followed, asapplicable.

90 WATER PROOF CEMENT PAINT SM 46WATER PROOF CEMENT PAINT Providing and applying 2 coats of snowcemto plastered and concrete surfaces including providing necessary scaffolding,surface preparation etc. complete. If additional coats are required to obtainuniform and smooth finish, the same shall be carried out at no extra cost.General specifications/guidelines given under WHITEWASH item also to befollowed, as applicable.

91 SANDTEX MATT SM 75SANDTEX MATT Providing and applying 2 coats of Sandtex matt paint ofSNOWCEM INDIA make and of required shades on all surfaces and heights togive an even shade including primer coat of snowcem plus. Generalspecifications/guidelines given under WHITEWASH item also to be followed, asapplicable.92 SY. ENML. PAINT OVER WALL SM 65

Page 177

SYNTHETIC ENAMEL PAINT OVER WALL Providing and applying 2 coats ofsynthetic enamel paint 1st quality of approved manufacturer and of requiredshades on wall to give an even shade including a primer coat. Generalspecifications/guidelines given under WHITEWASH item also to be followed, asapplicable.93 SY.ENML.PAINT OVER STEEL/WOOD SM 70SYNTHETIC ENAMEL PAINT OVER STEEL/WOOD SURFACE Providing andapplying 2 coats of synthetic enamel paint 1st quality of approvedmanufacturer and shades on steel surface to give an even shade including twocoats of red oxide primer. General specifications/guidelines given underWHITEWASH item also to be followed, as applicable.

94 POP PUNNING SM 85ON WALL & CEILING : Providing and applying Plaster of Paris(POP) punningon walls, ceilings, beams and columns to bring the surface in plumb line andlevel including making the surface smooth etc. complete. The rate shall includepreparing the surface with POP and compatible putty to give a smooth finish asper approval of the Engg.-In-Charge. Rate to include cost of scrapping, neurofinish etc. complete if needed.95 POP -MOULDING MR 146Plaster of Paris (POP) Moulding : Providing and fixing moulding of size 3" x 3" inthe edge of the wall and the ceiling with necessary hardware, properly finished,all material and labour complete.

96 MS GRILL KG 58Supply, installation and fixing of Prefabricated MS grill (IS 2062 Latest Edition)using MS flat/structurals / bars / hollow sections / strips / pipes etc as per designgiven by HPCL and direction of Engg.-In-Charge. Rate to include erection,grouting of posts in PCC 1:1.5:3, painting by two coats of red oxide primer andtwo coats of synthetic enamel of approved shade. Grouting PCC to be paidseparately as per relevant item.97 MS LADDER KG 57Supply, installation and fixing of Prefabricated MS Ladder/ Stair case/ baluster/MS Bars (IS 2062 Latest Edition) using MS flat/structurals / bars / hollowsections / strips / pipes etc as per design given by HPCL and direction of Engg.-In-Charge. Rate to include erection, grouting of posts in PCC 1:1.5:3, painting bytwo coats of red oxide primer and two coats of synthetic enamel of approvedshade. Grouting PCC to be paid separately as per relevant item.98 ANOD.AL.GLZ. DOOR-12MM GLASS SM 3120ALUMINIUM GLAZED DOOR/ FIXED GLAZING WITH 12MM GLASS:Providing and fixing Aluminium glazed door/ fixed glazing with 25 microncoloured anodised aluminium section minimum wall thickness of not less than2 mm with extruded built up section of approved make and weight ratio jointsmitred ad joint with heavy duty aluminium pressure die cast cleats with fins tomatch the section of frames conforming to approved section and shutterconforming to approved sections and glazed with 12 mm thick glass fixed toshutter with AL snap beading and neoprene /PVC gaskets/CP brass/Stainlesssteel screws and fixed to the wall with requisite rawl plugs and screw or withfixing clips or with expansion hold fasteners incldg. required filling up of gaps atjunctions,top ,bottom ,sides with PVC/Neoprene felt/Polysulphide sealant/siliconsealant all complete as per advise. Al-anodised shop front (Doors & fixedglazing) with frames at top & bottom and at two ends of JINDAL or equivalent

Page 178

Round acrylic handle and locking arrangement to be provided for main door.The glass should be single piece only. All glass edges shall be grinded andpolished smooth as per instructions. The floor spring strut shall be fixed andaccommodated in Aluminium section groove. In case of non-availability,approved equivalent make for Al sections is JINDAL. Approval of Engg.-In-Charge shall be taken before using equivalent sections matching next higherdimensions and weight per running metre without extra cost. Approved Make ofGlass: AIS, Modi, Saint Gobain, Triveni99 AL. GLZ. DOOR/FIXED GALZING-12MM TOUGH.GLASS SM 4267Same as above but with 12 mm toughened glass.

100 PDR.COAT.AL GLZ. DOOR/FIXED GALZING-12mm… SM 3215With Powder Coated aluminum section of approved colour having coatingthickness of minimum 50 micron with 12mm plain glass and all specificationsame as item above101 PDR.COAT.AL GLZ. DOOR/FIXED GALZING-TOUGH…. SM 4400Same as above but with 12 mm toughened glass.

102 HY. FLOOR SPRING EA 2300HYDRAULIC FLOOR SPRINGS Providing and fixing double action hydraulicfloor springs of approved brand ( HARDWYN / EVERITE/ SANDHU)conforming to IS 6315 : 1992 for aluminium doors. Rate to include cutting offloors as required, embedding in floors and cover plates etc complete as perspecifications. Load Capacity = 61-80 kg103 AL. PANELLED DOOR SM 3040ALUMINIUM PANELED DOOR : Providing and fixing 15 micron coloredanodised single leaf aluminium door with minimum wall thickness of not lessthan 2 mm , joints mitred and jointed with heavy duty aluminium pressure diecast cleats with fins to match the outer frames and door frames conformingJINDAL sections as specified fully paneled with 9 mm thick pre-laminated 3layers medium density ( exterior grade) particle board Grade-1, type -IIconforming to IS:12823 bonded with phenolformaldehyde synthetic resin ofapproved brand and manufacturer fixed to shutter with aluminium snap beadingand neoprene / PVC gasket / CP Brass /stainless steel screws fixed to the wallwith requisite rawl plugs and screw or with fixing clips or with expansion holdfasteners including necessary filling up of gaps at junctions, at top , bottom andsides with requisite PVC/neoprene felt/polysulphide sealant/silicon sealantincluding hard ware such as tower bolt of 150 mm length from inside and on both sides, 3 nos. Aluminium hinges of 100 mm length etc all complete asper architectural drawing. Aluminium door section of JINDAL make or equivalentmake with the following section : Main frame on all sides - 4700 -101.6 x 44.45 x2.5 of weight 1.977 kg/m Shutter vertical frame- 4537 - 53.7x44.45x2.3 of weight1.238 kg/m. Shutter top frame - 4540 - 53.7x44.45x2.3 of weight 1.173 kg/m.

Shutter middle frame - 4621 - 49.91x44.45x3 of weight 1.495 kg/m Shutterbottom frame - 4524 -83.5x44.45x3 of weight 2.107 kg/m, aluminium Cast Doorhandle and Clip - 4420 - 19x17.3x0.9 of weight 0.124 kg/m. In case of non-availability, approved equivalent make for Al sections is HINDALCO. Approval ofEngg.-In-Charge shall be taken before using equivalent sections matching nexthigher dimensions and weight per running metre without extra cost.

104 AL. WINDOWS OPENABLE SM 2656

Page 179

ALUMINIUM WINDOWS (OPENABLE) : Providing and fixing 15 micron colouranodised/ powder coated aluminium glazed windows with 5 mm glass &extruded built up section of wall thickness not less than 1.4 mm and approvedmake with glass panel fixed to side -hung shutter with aluminium snap beadingand neoprene / PVC gasket / CP Brass /stainless steel screws fixed to the wallwith requisite rawl plugs and screw or with fixing clips or with expansion holdfasteners including necessary filling up of gaps at junctions at top , bottom andsides with requisite PVC / neoprene felt / polysulphide sealant/silicon sealantincluding heavy duty handle cum locking arrangement etc all complete as perarchitectural drawing and the direction of Engg.In-charge.

105 AL. SLIDING WINDOWS 3 TRACK SM 2600Same as above but Aluminium sliding windows of Jindal make shutter sections:Top & Bottom - 8820- 1.5 mm thick @ 0.547 kg/m; Handle Section 8822- 1.5mm thick @ 0.547 kg/m; Shutter Interlock 8821- 1.45 mm thick @ 0.607 kg/m.Rate includes wheels/bearings, interlocking arrangements etc. complete. Thetrack section shall be as follows: Two Track Window: Top & Side - 8931-1.5 mm thick @ 0.784 kg/m; Bottom(Bulb) - 8932- 1.5 mm thick @ 0.909 kg/m

106 AL. SLIDING WINDOWS 2 TRACK SM 2550Same as above Item but Two Track Window: Top & Side - 8933-1.5 mm thick@ 1.06 kg/m; Bottom (Bulb) - 8934- 1.5 mm thick @ 1.248 kg/m

107 AL. LOUVERED VENTILATOR SM 1955ALUMINIUM LOUVERED VENTILATOR : Providing and fixing 15 microncolour anodised/powder coated aluminium ventilator with extruded built upsection of wall thickness not less than 1.5 mm and approved make glazed with 5mm thick opaque glass louver 100mm wide.

108 AL.GL.DOOR/FIXED GLZ 6mm THK SM 2522ALUMINIUM DOOR/FIXED GLAZING WITH 6 MM GLASS : Providing and fixing15 micron coloured anodised aluminium fixed glazing/aluminium door with 6mm glass extruded built up section of wall thickness not less than 1.5 mm andapprove make with glass panel fixed with Aluminium snap beading/Neoprene / PVC gasket/CP Brass /stainless steel screws and fixed to the wallwith requisite rawl plugs and screw or with fixing clips or with expansion holdfasteners including necessary filling up of gaps at junctions, at top , bottom andsides with requisite PVC / neoprene felt/ polysulphide sealant/silicon sealant allcomplete as per architectural drawing and the direction of Engg. In-charge.Aluminium section of JINDAL make or equivalent make with the followingsections : Outer frame sections - 4688- 63.5x38.1x1.65 of weight 0.942 kg/m.Intermediate frame - 4687- 63.5x38.1x1.53 of weight 0.942 kg/m. Glass panelsused shall not be less than 2.4 m (height) x 1.2 m (width). All the joints shall be Door:Outer side frame - 4550 - 47.62x44.45x1.52 of weight 0.881 kg/m.Bottom frame - 4553 - 95.25x44.45x1.70 of weight 1.301 kg/mIntermediate frame - 4621- 49.91x44.45x1.60 of weight 0.882 kg/m.Clip- 4420- 19x17.3x0.9 of wt. 0.124 Kg/m.The floor spring strut shall be fixed and accommodated in Aluminium sectiongroove. The door shall be provided with die cast aluminium handle, towerbolt,locking arrangement etc. complete. The joints and gaps shall be treated withsilicon sealant to stop water ingress and glass surfaces shall be cleaned neat ofleft over sealant. Approved Make of Glass: AIS, Modi, Saint Gobain, Triveni. Incase of non-availability, approved equivalent make for Al sections is JINDAL.Approval of Engg.-In-Charge shall be taken before using equivalents matchingnext higher dimensions and weight per running metre without extra cost.

Page 180

109 STEEL WINDOWS SM 2095STEEL WINDOWS : Supply, fabrication and fixing of MS glazed windows usingapproved Z sections with 5mm plain glass including providing grill with 12mmsquare bar @100mm c/c , painting with two coats of red oxide primer and twocoats of synthetic enamel paint, handle , stay arrangement etc. complete.

110 STEEL DOORS SM 2095STEEL DOORS : Supply, fabrication and fixing of MS Door using 35x35x5 angleframe and 25x25x3 angle members including bracings with 16 gauge MS sheetstitch welded to Door shutter frame complete as per direction of Engg.-In-Charge painting with two coats of red oxide primer and two coats of syntheticenamel paint, handle , stay arrangement ,tower bolt etc. complete.

FLUSH DOOR Providing and fixing solid core flush door in single leaf 35mmthick commertial plywook of seasoned wood without ventilator. Door frame to bemade of 60mm x 100mm teak wood with wrough iron hold fasts. Door to befitted with brass fitting-hinges, handles on both sides, tower bolts, etc., complete.Frame to be painted in three coats of synethic enamel paint over a coat of woodprimer including scrapping, surface preparation etc., complete.Door(leaf) to belaminated on both sides with laminations 1.5 mm thk and grey in color ofapproved make/brand.Approved Make: Kitply/ Anchor Board/ Wonder wood/Duro/ National or approved equivalent.

111 FLUSH DOOR 900x2100mm: EA 7605Providing and fixing solid core flush door in single leaf 35mm thick commertialplywook of seasoned wood without ventilator. Door frame to be made of 60mmx 100mm teak wood with wrough iron hold fasts. Door to be fitted with brassfitting-hinges, handles on both sides, tower bolts, etc., complete. Frame to bepainted in three coats of synethic enamel paint over a coat of wood primerincluding scrapping, surface preparation etc., complete.Door(leaf) to belaminated on both sides with laminations 1.5 mm thk and grey in color ofapproved make/brand.Approved Make: Kitply/ Anchor Board/ Wonder wood/Duro/ National or approved equivalent. Size 900X2100mm

112 FLUSH DOOR 750x2100mm EA 7400Same as above but size 750X2100mm

113 ROLLING SHUTTER SM 2200ROLLING SHUTTER Supply, fabrication and fixing of MS rolling shutter of thefollowing specifications including grill window of 300 mm height at eye level forvisibility even in closed position. Code: Conforming to IS 6248 – 1979 Type: SelfCoiling type (manual) Curtains: Interlocking cold rolled lath section of 0.8 mmthickness. Lock plate : MS sheet of 3.15 mm thick reinforced with MS angles of35 x 35 mm. Guide channel : MS sheets of 3.5 mm thick Bracket Plate : MSSheet of 0.9 mm thick. Hood Covers : MS sheet of 0.9 mm thick Locking handle: To be provided suitably. Rate shall include providing and fixing holdfasts andpainting two coats of enamel paint of approved make and shade over two coatsof zinc phosphate primer. Shutter up to 10 SQM -push pull type hand operatedwith ball bearings , For 10 SQM upto 30 SQM- Mechanical operated gear typewith ball bearing, a pulling hook shall be provided for each of the rolling shutter.

114 GRILL IN ROLLING SHUTTER SM 2400

Page 181

GRILL IN ROLLING SHUTTER : Supply, fabrication and fixing of manuallyoperated steel rolling net shutter as per the specification. Nets to be inhexagonal pattern, The round MS bars used for jali should be 8mm in dia . Allother specification as that of item for rolling shutter above.115 DISPLAY SHELF SM 3090DISPLAY SHELF: Providing & fixing in position 12 mm thick plain glass ofModi/AIS/Saint Gobain/Triveni make with polished edges in the groovesbetween the 25 mm thick exterior grade MDF board planks at 325 mm c/c & 350mm wide. The MDF board shall be fixed on teak wood frame fixed to the wallusing plugs, screws and holdtights. Cross section of teak wood shall be 50x75mm. The teak wood shall be seasoned and brushed with anti-termite chemicalbefore use. Teak wood framing shall be fixed over wall in such a way that itforms grids of size 450x325 mm so as not to obstruct the grooves. The exposedsurface of the MDF board shall be finished with 1.5 mm thick lamination ofapproved colour & combination of colours with teak wood beadings on edges.The approved brand for the lamination shall be Formica/Greenlam / Sundek.

116 STORAGE & SHELVES SM 3320Specifications as above item but with storage at bottom, as per the standarddrawing.

117 MS FAN HOOKS EA 73FAN HOOKS : Providing & fixing MS fan hooks with 16 mm dia MS bar bent toshape with hooked ends in RCC Slab during laying including painting theexposed portion.

118 MORTICE LOCK EA 900MORTICE LOCK Providing & fixing GODREJ make only six lever lock (Cylindrical/ Round Head ) including all necessary hardware etc.

119 DOOR CLOSER EA 850DOOR CLOSER Providing and fixing door closer of Hardwyn / Everite makesize no. 2.

120 STRUCT STEEL FOR SERVICE BAY TM 57000Supplying , erecting and fixing in position Pre- fabricated structures at allelevations for service bay using structural steel sections conforming to IS:2062, including cutting, welding or bolting, supply of bolts/nuts/washers etc., completeas per drawings including surface preparation and applying one coat of ZincPhosphate Primer before erection and two coats of synthetic enamel paint asper specification after erection and all materials and labour complete. ( Nowelding is permitted at site). The rate quoted shall include cost of bolts, nuts,washers, welding and electrodes and any other consumables required forcompleting the work. The bolts , nuts , washers, welds etc shall not be 121 AC SHEET FOR ROOF SM 304Supply , erection and fixing of corrugated asbestos cement sheet of Everestmake or approved equivalent for service bay including supply and fixing ofbitumen/GI washer, J bolt etc. For Roof122 AC SHEET FOR SIDE SM 320Same as above Item but for side sheet including gable end.

123 BARRICADING SM 306(50x50x5 mm ) at every 2.4 m c/c and horizontal support of 40x40x5 angle atequal distance for 8' ht &. The Job includes grouting vertical angle supports inRCC 1:2:4, fixing the sheets with necessaru J hooks, painting with syntheticenamel paint in Yellow and Black strip combination, and dismantling & disposingoff the entire material after completion of work.

124 GY. BOARD FALSE CEILING SM 755

Page 182

Providing and fixing Gyp board false ceiling with required accessories INDIAGYPSUM make including painting with two coats of plastic emulsion paint. 12.5mm thick 'Gypboard' shall be screw-fixed to the underside of suspended GI grid.GI grid shall be installed as per manufacturer's specifications. GI grid shallconsist of ceiling sections (India Gypsum Code no. MF5) at maximum c/cdistance 450 mm, Perimeter channel (India Gypsum code no. MF6A),intermediate channels (India Gypsum code no. MF7) at maximum c/c distance The ceiling sections should be fixed to intermediate channels with connectingclips (India Gypsum code no. ME9). GI grid shall be fixed to RCC slab abovewith the help of 25x0.5 mm strap hanger (India Gypsum code no. MF 8) andsoffit cleat (India Gypsum code no. P534). The joints between soffit cleat andstrap hanger and GI grid & strap hanger shall be with 6.4x12.7 mm nut and bolt(India Gypsum code no. P526). Soffit cleat shall be fixed to RCC ceiling withW.E. type 12 mm dia, 17/16" long steel rawl plug. Maximum c/c distance (bothways) of strap hangers shall be 1200 m. The Gypboard shall be fixed fixed to GIgrid with 25 mm long Drawall screws. The Gypboard to be used shall be 12.5mm thick tapered edge boards. The boards shall be taped & filled from The rate shall be inclusive of additional ceiling sections and intermediatechannels shall be provided at openings for light fixtures, AC ducts, verticaldrops, offsets etc Additional intermediate channels shall be fixed to straphangers at every 1200 mm for additional support to prevent strap hangers frombuckling/swaying. Item to be completed in all respect including necessarysleeves for ducts , finishing of joint cut outs, supports for AC grills, light fixtures,speakers etc. complete as per directions of Engg.-In-Charge.125 MINARAL FIBRE FALSE CEILLING ( ARMSTRONG) SM 1041Providing and fixing Mineral Fibre board false ceiling ( Armstrong Make) withrequired accessories including fixing of the GI channels (18 guage), fixing of thesheets in pattern , in proper line & level, filling the joint with sealent etc. completeas per the satisfaction of EIC.

126 ACOUSTIC. SUSP. CEILING BUTT.. SM 920Providing & Fixing of Armstrong Acoustical Suspended Ceiling System with Fissured Tiles having butt edges . The tiles should have Humidity Resistance of 90% RH, Average NRC .50, Light Reflectance >80%, Thermal Conductivity k = 0.052 – 0.057 w/m°c, Colour White, Fire Performance Class 0/Class 1 (BS - 476) in module size of 600mm x 600mm x 15mm laid on 24XL - Hot Dipped Galvanised steel suspension System having rotary stitching on the Main Runner, 1200 mm & 600 mm Cross Tees. INSTALLATION: To comprise main runner spaced at 1200mm centres securely fixed to the structural socket by approved hanger at 1200mm maximum centre. The last hanger at the end of each main runner should not be greater than 450mm from the adjacent wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm centre to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees.Perimeter trim to be Armstrong wall angles or channel, secured to walls at 450 127 ACOUSTIC. SUSP. CEILING TEGULAR SM 1200

Page 183

Providing & Fixing of Armstrong Acoustical Suspended Ceiling System with Fissured Tiles having Tegular edges . The tiles should have Humidity Resistance of 90% RH, Average NRC .50, Light Reflectance >80%, Thermal Conductivity k = 0.052 – 0.057 w/m°c, Colour White, Fire Performance Class 0/Class 1 (BS - 476) in module size of 600mm x 600mm x 15mm laid on 24XL - Hot Dipped Galvanised steel suspension System having rotary stitching on the Main Runner, 1200 mm & 600 mm Cross Tees. INSTALLATION: To comprise main runner spaced at 1200mm centres securely fixed to the structural socket by approved hanger at 1200mm maximum centre. The last hanger at the end of each main runner should not be greater than 450mm from the adjacent wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm centre to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees.128 EUROPEAN TYPE W/C- WHITE EA 3320EUROPEAN TYPE Supplying and fixing white wall mounted vitreous chinaEuropean type water closet comprising of the following accessories includingcutting and making good the walls & floors wherever required complete asdirected by Engg.-In-Charge, having following (A) White vitreous chinaEuropean water closet with P or S trap of Parryware make Cascade series No.0219 having integral matching colour vitreous china cistern supplied as part ofthe closet with all mechanisms, with necessary fittings, brackets, screws, etc allcomplete as per the direction of Engg.-In-Charge.(B) 15mm NB CP brass angle valve of approved brand as per the direction ofEngg.-In-Charge (C) 15 mm NB CP brss inlet connection with Brass unions atthe ends. (D) Parryware/Commander make or equivalent matching colourpolypropylene seat cover with necessary brass hinges and rubber bushes etc(E) WC connector with neoprene rubber etc. Approved Equivalent - Hindware20028 with matching colour Vitreous China cistern with all mechanisms, fittingsetc. complete.129 EUROPEAN TYPE W/C- OFF WHITE EA 4325Same as above but OFF WHITE

130 INDIAN TYPE W/C- WHITE EA 2830INDIAN WATER CLOSET Supplying and fixing white coloured vitreous chinaOrissa Pan type water closet comprising of the the following accessoriesincluding cutting and making good the walls & floors wherever required completeas directed by Engineer In Charge. A)Coloured (pastel colour) viterous china580 mm orissa pan water closet of Hinduatn sanitaryware or any equivalentmake with P or S trap. B) 10 litres capacity hi-grade engineering plastic low levelflushing cistern of matching colour Parry Slimline make model 8068 or approvedequivalent make with necessary fittings , brackets , screws etc. all complete . C)32 mm PVC flush pipe 10 Kg/Sqcm quality of approved lengt with necessaryfittings ,clamps etc. D) 15 mm NB CP inlet connections with brass union at theends E) 15 mm NB brass angle valve as per ISI of approved brand as per thedirection of Engineer In Charge F) WC connector with neoprene rubber\.

131 INDIAN TYPE W/C- OFF WHITE EA 3715Same as above but OFF WHITE

132 URINALS EA 1920

Page 184

URINALS : Supplying and fixing colored ( pastel coloures) vitreous china flatback urinal of size 300 mm x 400 mm with integrated overflow of HindustanSanitory or equivalent approved make with CP flush valve , CP pipe connection ,CP waste coupling , CP Brass bottle trap of Jaquar mak, 32 mm PVC waste lineof required length etc all complete as per the direction of engineer in charge.

133 LARGE URINALS - MAGNUM EA 3665Supplying and fixing coloured (pastel colours) viterous china flat back urinal oflarge size with integrated overflow system of Hindware Sanitary make,MODELNO: 60002 or approved equivalent from Parryware-MAGNUM ,withSpreaders,CP flush valve, CP pipe connection, CP waste coupling , CP Brassbottle trap of Jaquar make, 32 mm PVC waste line of required length etc. allcomplete as per the direction of Engineer In Charge 134 URINALS WITH BUILT IN SENSORS EA 13375Supplying and fixing coloured (pastel colours) viterous china flat back urinal oflarge size with integrated auto flush system of 0575 New Magnum ParrywareSanitary make with CP flush valve of Jaqaur make, cp pipe connection, CPwaste coupling , CP Brass bottle trap of Jaquar make, 32 mm PVC waste lineof required length etc. all complete as per the direction of Engineer In Charge

135 URINAL DIVISIONAL PLATE EA 2345URINAL DIVISION PLATE Providing and fixing 1200 x 450 x 18 mm size granitepartition plate between urinals including cutting masonary/concrete surface torequired size, fixing the division plate on the ceramic tiles by means of SSclamps, nuts & bolts, polishing all exposed surface etc all complete as directedby Engineer In Charge.

136 URINALS SENSORS EA 8650Supply, installation and commissioning all complete Jaquar make SensotronicConcealed type Flushing system (Model 51087 - Chrome) including allaccessories, all connections, electricals etc. all complete as per the direction ofEngg.-In-Charge.137 HAND WASH BASIN EA 2350HAND WASH BASIN Providing and fixing coloured (pastel colours) wash basinsof size 550 x 400 without pedestal Including the following accessories: -15mmbrass CP Jaquar make (Cat.no.093) stop cock -1 No . -15mm CP connectionsfrom the above stop cock to pillar cock - 1 No. -32mm dia waste coupling, CPbrass chain and rubber stopper. -30mm Dia. bottle trap Jaquar make withcleaning eye, extension piece and wall flange. -Providing and fixing brass CPJaquar make 13mm half turn pillar cock.(Cat. no.011)Rate to include supply ,painting and fixing of necessary CI brackets with nuts and bolts and fixing thewash basin with all necessary connections in walls .138 COUNTERTOP WASHBASIN OVAL TYPE EA 5450Providing &fixing colored COUNTER TOP washbasin :OVAL below CounterBasin 550 0418 of Parryware/10016 HINDWARE Or appoved equivalentincluding all the required accessories like: -15mm brass CP Jaquar make(Cat.no.093) stop cock -1 No . -15mm CP connections from the above stop cockto pillar cock - 1 No. -32mm dia waste coupling, CP brass chain and rubberstopper. -30mm bottle trap Jaquar make with cleaning eye, extension piece andwall flange. -Providing and fixing brass CP Jaquar make 13mm half turn pillarcock.(Cat. no.011)

139 EWC EUR.WALLMOUNT (CAS. OFF WT.) EA 12000

Page 185

Providing &fixing WC Europeun WALL MOUNTED WC CASCADE 0219PARRYWARE OR 20028 -HINDWARE (offwhite) with P or approved equivalentof Hindware with P or S trap INCLUDING ALL THE ASSOCAITEDACCESSORIES AND FITTINGS like WC cover of approved make ,15mm NBbrass angle valve as per BIS of approved brand ,15 mm NB CP inlet connectionwith brass unions at the ends,WC connector with neoprene rubber withnecessary fittings ,brackets, screws etc. all complet as per the satisfaction ofEngineer-in-charge.

140 SENSOR TAPS FAUCET EA 11520Providing and fixing in position CP sensor Faucet of 51071 Jaquar make as perthe drawing. The item includes all necessary fittings, accessessories etc.complete as per the direction of Engineer In Charge .

141 CP TOWEL RING CLARION JAQUAR EA 755Providing and fixing in position CP TOWEL RING CP mounted on wall of make1121 CONTINENTEL JAQUAR

142 AUTOMATIC HAND DRYER EA 7980Providing, fixing and commissioning fully automatic hand dryer i.e. autostart onpositioning the hand and autostop. Care shall be taken so that tiling is notdamaged while installation. Rate includes PVC insulated power chord havingcopper conductor and Anchor ROMA make 3 pin power plug matching ampereload of instrument. Make - Technocrats (Model Alpha AP-800) or Euronics(Model CYC 30)

143 AUTO FRESHENER EA 2850Providing, fixing and commissioning fully automatic aerosol dispenser (AutoFreshener). The price includes spray fragrance cam with approved aroma etc.complete. Rate includes PVC insulated power chord having copper conductorand Anchor ROMA make 3 pin power plug matching ampere load of instrument.Care shall be taken so that tiling is not damaged while installation. Make -Technocrats (Model Deluxe)

144 AUTOMATIC SHOE POLISH MACHINE EA 17100Providing, fixing and commissioning fully automatic shoe polish machine withelectronic eye (infra red sensor) having both separate black and brown rollers.The machine shall start automatically when shoe is placed and automaticallystop. Rate includes PVC insulated power chord having copper conductor andAnchor ROMA make 3 pin power plug matching ampere load of instrument.Care shall be taken so that finishing is not damaged while installation. Make -Technocrats (Model Executive Deluxe)

145 STOPCOCK CONCEALED-PARKO 1516 EA 535Providing and fixing in position CP brass stop cock Parko make classic lineseries No. 1516 including all necessary fixtures etc. complete.

146 SWAN NECK TAP-PARKO 1536 EA 808Providing and fixing in position CP brass swan neck tap Parko make classic lineseries No. 1536 on wash basins including all necessary fixtures etc. complete.

147 PILLAR COCK-PARKO 1501 EA 525Providing and fixing in position CP pillar cock of Parko make classic line seriesNo. 1501 including all necessary fixtures etc. complete.

148 BIB COCK LONG BODY-PARKO 1511 EA 539Providing and fixing in position CP long body bib cock of Parko make classic lineseries No. 1511 including all necessary fixtures etc. complete.

149 BIB COCK LONG NOSE-PARKO 1506A EA 622

Page 186

Providing and fixing in position CP long nose bib cock of Parko make classic lineseries No. 1506 A including all necessary fixtures etc. complete.

150 BIB COCK -PARKO 1506 EA 423Providing and fixing in position CP bib cock of Parko make classic line seriesNo. 1506 including all necessary fixtures etc. complete.

151 PILLAR COCK-JAQUAR 23011 EA 552Providing and fixing in position CP brass pillar cock with Aerator of JaquarClarion Range No. 23011. Rate to include all related civil repairs, fitments,joineries etc. complete.

152 PILLAR COCK-JAQUAR 23021 EA 690Providing and fixing in position CP brass long neck pillar cock with Aerator ofJaquar Clarion Range No. 23021. Rate to include all related civil repairs,fitments, joineries etc. complete.

153 BIB COCK-JAQUAR 23037 EA 530Providing and fixing in position CP brass bib cock of Jaquar Clarion Range No.23037. Rate to include all related civil repairs, fitments, joineries etc. complete.

154 BIB COCK-JAQUAR 23039 EA 550Providing and fixing in position CP brass bib cock with long thread of JaquarClarion Range No. 23039. Rate to include all related civil repairs, fitments,joineries etc. complete.

155 BIBCOCK LONG BODY-JAQUAR 23107 EA 735Providing and fixing in position CP brass long body bib cock with wall flange ofJaquar Clarion Range No. 23107. Rate to include all related civil repairs,fitments, joineries etc. complete.156 BIB COCK-2 WAY-JAQUAR 23041 EA 795Providing and fixing in position CP brass bib cock of Jaquar make ClarionRange No.23041. Approved equivalent Parko make.

157 ANGULAR STOP COCK-JAQUAR 23053 EA 524Providing and fixing in position CP brass angular stop cock (regulating valve) ofJaquar Clarion Range No. 23053. Rate to include all related civil repairs,fitments, joineries etc. complete.

158 ANGULAR STOP COCK-JAQUAR 23055 EA 552Providing and fixing in position CP brass long thread angular stop cock(regulating valve) of Jaquar Clarion Range No. 23055. Rate to include all relatedcivil repairs, fitments, joineries etc. complete.

159 CONCEAL. STOPCOCK-JAQUAR 23069 EA 705Providing and fixing in position CP brass concealed stop cock (reduced body) ofJaquar Clarion Range No. 23069. Rate to include all related civil repairs,fitments, joineries etc. complete.

160 CONCEAL. STOPCOCK-JAQUAR 23083 EA 840Providing and fixing in position CP brass Extra Heavy Body concealed stop cockwith adjustable wall flange of Jaquar Clarion Range No. 23083. Rate to includeall related civil repairs, fitments, joineries etc. complete.

161 SS GRAB BAR DESIGN A/B EA 6000SS GRAB BAR (A) and (B):Fabricating and fixing S. S. Railing with 40 mm diaMS Piperail & using 10X10 MS bar welded to Balaster ( diagonal pieces) and20 x 20 MS Baluster as per the drawing. (GRAB BAR A &B).The item includesfabrication, buffing of the railing upto req. finish, fixing the railing at position withm20 grade concrete, finising the SURFACE properly etc. complete

162 SS STAIRCASE RAILING MR 2300

Page 187

SS STAIRCASE RAILING ::Fabricating and fixing S. S. Railing with 40 mm diaMS Piperail & using 10X10 MS bar welded to Balaster ( diagonal pieces) and20 x 20 MS Baluster as per the drawing. (STAIRCASE DETAIL -HPCL-A-J100-DD-65.The item includes fabrication, buffing of the railing upto req. finish, fixingthe railing at position with m20 grade concrete, finising the SURFACE properlyetc. complete

163 MIRROR 600X600X5.5 EA 675MIRROR Providing and fixing bevelled edge mirror of superior glass of 5.5 mmthick & 600 x 600 mm size of BELGIUM GLASS or any other equivalent make,3mm thick felt backing or 6 mm asbestos sheet or with wooden beads allroundof specified size and fixed with wooden plugs with CP brass screws and cupwashers etc all complete as directed by Engineer In Charge

164 MIRROR 5.5 MM THK SM 1865Providing and fixing beveled edge mirror of superior glass of 5.5 mm thick ofBELGIUM GLASS or any other equivalent make, craft paper, 3mm thick feltbacking or 6 mm asbestos sheet. Teak Wood beads 25x40 mm as perapproved shape/drawing allround and fixed with wooden plugs with CP brassscrews and cup washers etc all complete as directed by Engg.-In-Charge.

165 SOAP TRAY EA 245SOAP TRAY Providing and fixing readymade CP brass soap tray near washbasin with CP brass screws of approved make.

166 LIQUID SOAP DISPENSERS EA 572LIQUID SOAP DISPENSERS Providing and fixing readymade CP brass liquidsoap dispenser near wash basin with CP brass screws of approved make.

167 TOILET PAPER HOLDER EA 403TOILET PAPER HOLDER Supplying and fixing of 150 x 150 mm pastel colouredtoilet paper holder of Hindustan Sanitary ware or equivalen approved make atrequired position and elevation as directed. Rate to include making good thechases in walls after fixing the above. 168 TOWEL RAIL EA 515TOWEL RAIL Providing and fixing CP brass towel rail of 20 mm dia and 600 mmlong including all accessories such as brackets (coloured), fixed and anchoringetc. complete as directed.

169 15MM DIA STOP COCKS EA 484Providing and fixing in position CP brass stop cock of heavy type ISI marked ofapproved make. Size 15mm diameter

170 15MM DIA BIB COCKS EA 555Providing and fixing in position CP brass bib cock of heavy type ISI marked ofapproved make. Size 15mm diameter

171 15MM DIA PILLAR COCKS EA 725Providing and fixing in position CP brass pillar cock of heavy type ISI marked ofapproved make. Size 15mm diameter

172 15MM DIA HALF TURN COCKS EA 865Providing and fixing in position CP brass half turn cock of heavy type ISI markedof approved make. Size 15mm diameter

173 HYGI SPRAY EA 595Providing and fixing in position CP brass Hygi Spray of Parryware make ModelT9929G1 inclusive of all fixtures, fittings and fasteners making operationalcomplete. Approved Equivalent Make - Hindware

174 15mm DIA CONCEALED GI PIPE MT 168

Page 188

Providing & fixing followg. size medium duty GI pipes of TATA/JINDAL/ZENITH/GST make conforming to IS-1239 concealed in the walls/underthe concrete floors including making chases in the walls/concrete floors,fixingwith clamps at every 1m c-c, necessarytees,bends,elbows,plugs,nipples,unions,testing of pipelines for leaks upto apressure of 6 Kg/sq cm , painting the pipes with hot bitumen, wrapping the pipeswith hessian cloth and making chases of the walls good after piping complete.175 20MM DIA CONCEALED GI PIPE MT 189Same as above but size 20 mm dia

176 15MM DIA EXPOSED GI PIPE MT 154Same as above but laying in open on brick or RCC surface with the help of MS'U' clamps at every 1 m and at every turn.

177 20MM DIA EXPOSED GI PIPE MT 174Same as above but size 20mm dia

178 25MM DIA EXPOSED GI PIPE MT 236Same as above but size 25mm dia

179 32 MM DIA EXPOSED GI PIPE MT 275Same as above but size 32mm dia

180 40 MM DIA EXPOSED GI PIPE MT 325Same as above but size 40mm dia

181 UPVC PIPE 40 MM DIA 4KG/SQCM MR 165Providing and laying unplasticised polyvinyl chloride (UPVC) pipes of class IV oras applicable conforming to IS 4985:2000/ IS 15328 : 2003/ IS 13592 : 1992Type B/ BS 4514/ BS EN 1329, latest edition including all necessary fittingsconforming to IS 14735 : 1999/ BS 4514/ BS EN 1329, latest edition and otheraccessories including connections etc., complete as per drawings or as directedat site. Size 40 mm diameter.182 UPVC PIPE 63 MM DIA 4KG/SQCM MR 221Same as above but size 63 mm dia

183 UPVC PIPE 90 MM DIA 4KG/SQCM MR 247Same as above but size 90 mm dia

184 UPVC PIPE 110 MM DIA 4KG/SQCM MR 275Same as above but size 110 mm dia

185 UPVC PIPE 160 MM DIA 4KG/SQCM MR 325Same as above but size 160 mm dia

186 40MM DIA GATE VALVE EA 1345Providing & fixing brass full way gate valve ISI marked & of Leader/GG make orapproved equivalent as directed by Enginner In Charge. Size 40 mm diameter

187 32MMDIA GATE VALVE EA 1159Same as above but size 32mm dia

188 25MM DIA GATE VALVE EA 765Same as above but size 25mm dia

189 15MM DIA GATE VALVE EA 482Same as above but size 15mm dia

190 WATER TANK-1000 LTRS EA 7200WATER TANK Supplying and installation of HDPE water tanks Sintex / Fusion /Polycon make of 1000 litre capacity including 300 mm high brick masonrypedestal of 230mm thick in CM 1:5, providing 75mm thick RCC 1:2:4 slab withreinforcement 8mm tor @150mm c/c, lifting the tank , making all necessary GIconnections to inlet, outlet, and overflow nozzles and cleaning the tank beforecommissioning.

191 WATER TANK-5000 LTRS EA 26980

Page 189

WATER TANK Supplying and installation of HDPE water tanks Sintex / Fusion /Polycon make of 5000 litre capacity including 300 mm high brick masonrypedestal of 230mm thick in CM 1:5, providing 75mm thick RCC 1:2:4 slab withreinforcement 8mm tor @150mm c/c, lifting the tank , making all necessary GIconnections to inlet, outlet, and overflow nozzles and cleaning the tank beforecommissioning.

192 110MM DIA PVC PIPE MT 292PVC SOIL / WASTE /RAIN WATER PIPE: Supplying and laying the PVC pipeof 6KG/sqcm pressure rating including plain or door type bends, shoes, offsets,clamps junctions, tees, etc, complete. Also including cutting, bending & supplyand laying of 17 SWG annealed binding wire inside the Pipe for pulling cables infuture. Size 110 mm diameter193 80MM DIA PVC PIPE MT 225Same as above but size 80mm diameter

194 NAHANI TRAP EA 653NAHANI (FLOOR) TRAP Providing and fixing PVC floor trap of self cleansingdesign conforming to IS specs with 100mm inlet, 75mm outlet and 150mm CPhinged grating of 6mm thick with rim. Rate shall include making all necessaryleak proof connections etc .

195 STONE WARE PIPES ( 150 MM DIA) MT 250STONE WARE PIPES Providing and laying 150mm dia. salt glazed stonewarepipes conforming to IS 651 Grade-A including bends, tees etc, excavation oftrenches, 100 mm thick PCC 1:4:8 bedding, providing PCC 1:2:4 haunches @0.5mc/c , filing the joints with tarred gasket, plastering with 1:3 cement mortarsmoke testing of joints,backfilling the trenches with excavated earth, watering,ramming etc., complete.CI PIPES Providing and laying ISI marked centrifugally cast (spun) Iron pipesconforming to IS 3989 :1984 latest edition incuding all bends, joints, Ts, cowlsetc. with painted MS clampings of appropriate strength @ 1 m c/c. The pipe willbe painted with two coats of red oxide and smoke tested after making joints andbefore joining to the system. The joints will be socket spigot caulked joints withjuite and molten lead/Drip Seal as per relevant BIS specifications andprocedures. Make - NECO/ HEPCO/ ACL or approved Equivalent

196 100MM DIA CI PIPE MT 765CI PIPES 100MM DIA Providing and laying CI pipes of 100mm dia of standardquality and make including fittings, bends, tees, etc.,complete.

197 75MM DIA CI PIPE MT 615CI PIPES 75MM DIA Providing and laying CI pipes of 75mm dia of standardquality and make including fittings, bends, tees, etc., complete.

198 GULLY TRAP WITH CHAMBER EA 1700GULLY TRAP WITH CHAMBER Providing and fixing square mouth gully trapincluding constructing 300 X 300 MM internal size brick masonary chamberwith 230mm thick brick masonary in 1:5 cement mortar, excavation, 75mm thickPCC 1:4:8 bed, plastering with neat cement finish, Medium duty CI cover withframe etc. complete.

199 25MM DIA NON RETURN VALVE: EA 1051Providing and fixing brass Non-Return Valve GG/LEADER make ISI marked orapproved equivalant

200 15MM DIA NON RETURN VALVE EA 905Same as above but size 15mm diameter

210 FLOAT VALVE EA 463

Page 190

FLOAT VALVE Providing and fixing Float Valve (Ball cock) of polypropylene orsynthetic metal (Symet) float and rod of approved make of 25mm dia. nominalbore.

202 600X600X600MM INSPN. CHAMBERS EA 2350Providing and constructing inspection chambers of size 600X600X600 mm\ with230mm thick brick masonary in 1:5 cement mortar, excavation, 75mm thickPCC 1:4:8 bed, plastering with neat cement finish etc. complete. ( Chambercover & angle Frames will be paid separately)

203 450X450X600MM INSPN. CHAMBERS EA 2100Same as above but size 450X450X600 mm

204 600X450X600 MM INSPN. CHAMBERS EA 2200Same as above but size 6000X450X600 mm

205 SEWER TRAP CHAMBER EA 3955SEWER TRAP CHAMBER Providing and constructing sewer trap with conicalframe work in 9" thick BM chamber with CM1:4 conical chamber of size 3.5"diaat top and 4.5" dia at bottom and depth as per required slope including cementplater inside and outsite with CM1:4 including necessary foundation andexcavation. The job includes providing CI cover of weight not less than 100KGs,etc., complete. The job is to be carried out as per local municipal rules andregulations by licensed plumber.

206 SEPTIC TANK (25 PERSON) EA 23400SEPTIC TANK Prpoviding & constructing septic tank of size1200x2000x1800mm depth with excavation ,PCC1:4:8 100mm thick bed ,345/230mm thick brick masonary wall in CM 1:5 ,RCC1:2:4 100mm thick slabwith 8mm tor steel @150c/c both way , 115mm thick baffle wall with RCC beamat bottom ,12mm thick smooth cement plaster with water proofing compoundinside and exposed outside portion, providing 600mmx600mm size medium dutyCI cover, providing 75mm dia PVC vent pipe etc. Complete.

207 SOAK PIT 2.5 M DIA X 3.0 M. DEPTH EA 11750SOAK PIT Providing and constructing soak pit of 2.5m dia X 3m depth (internal)in brick masonry of class 75 design. Internal size of shaft shall be minimum clear1m with minimum 230thk. walls in cement mortar 1:6 at top 500mm in heightand in bottom 230mm wall in height with 450mmx450mm dry brick honey combshaft and surrounded by broken brick bats. The outer walls of the shaft shouldbe 230 mm followed by 150 mm thick layer of 50-80 mm nominal size brickaggregates thereafter followed by 150 mm thick layer.

208 CI COVER 450X450MM - 16 KG EA 660CI covers for Chambers / Inspection chambers etc : Supply and fixing of CIcover and frame of 450X450 mm nominal size(total weight not less than 16 kg)with seal, all materials and labour complete.

209 CI COVER 600X600MM - 34 KG EA 1550Same as above Item but of size 600x600 mm and total weight not less than 34kg.

210 PT.WIRING MOD. PLT SWITCH LT/FAN EA 650

Page 191

POINT WIRING FOR LIGHT/FAN WITH MODULAR PLATE SWITCHESANCHOR/MK Providing and laying point wiring in concealed conduits for thefollowing points using specified 1100V grade PVC insulated,FRLSmultistranded 3 x 1.5 sqmm copper conductor wires. Rate to include supplying,laying and securing in position in roof slabs and brick walls or concrete columns25 mm dia rigid PVC conduits of approved make with necessary accessoriesand junction boxes/pull boxes. Providing and fixing in the brick wall flush typemetal switch boxes of approved make shade and sufficient size to accomodateall 6A Modular switches/3 pin socket,screws,holders .ceiling roses and fanregulator wherever required. Rate to include wall chasing and rough plastering .Providing and fixing single pole 5A modular plate switches of MK or ANCHORmake of approved colour.One switch shall be provided for each light and fanpoint. Rate to also include providing main circuit wiring from DB to switchboards with 2.5 sqmm copper wire .

211 5A SOCKET SWITCH EA 450Same as above but for 5A socket controlled by one 5A switch on the same

lighting board212 5A SOCKET SWITCH INDEPENENTLY EA 550

Same as above but for 5A socket controlled by one 5A switch independentlymounted including providing wiring with 3 runs of 1.5 sqmm pvc insulatedcopper wire through PVC conduit

213 5/15A SOCKET SWITCH EA 585Same as above but for 5/15A socket controlled by 15A switch independentlymounted including providing wiring with 2 runs of 2.5 sqmm and 1 run of 1.5sqmm PVC insulated copper wire through PVC conduit

214 AC POINT EA 1910Same as above but for for AC point with 2 runs of 4 sqmm (P&N)and 1 run of2.5 sqmm (earthing) PVC insulated , FRLS multistrand copper cable in 25 mmdia PVC conduict from MCBDB to 20 A powersocket. The conduit shall bepartly/fully concealed in all types of wall, ceiling etc complete with allaccessories, wiring, termination, connected civil works, rough plastering etcincluding supply and fixing of 20A industrial socket controlled by 20A SPMCB ofMDS/HAVELS make.

215 4X10+1X6 SQMM MULTIST.FRLS CU MR 315Supply, laying, and commissioning of wiring using 4 runs of 10 sqmm and 1 runof 6 sqmm PVC insulated , FRLS, unsheathed, multistranded copper wiresconforming to IS 694:1990 in 40 mm dia medium duty PVC conduit (Conforming to IS 9537:Part 3:1983) from panel to Distribution boards. Rate to includesupply of 16 GI fish wire, conduits & accessories, wiring, terminations etccomplete.

216 4X6+1X4 SQMM MULTIST. FRLS CU MR 225Same as above item but supply, laying, and commissioning of wiring using 4runs of 6 sqmm and 1 run of 4 sqmm FRLS multistranded copper wire in 32mm dia PVC conduit from panel to Distribution boards.

217 4X6+2X4 SQMM MULTIST. FRLS CU MR 252Same as above item but supply, laying, and commissioning of wiring using 4x6sqmm and 2x4 sqmm FRLS multistranded copper wire in 40mm PVC conduit

218 3X10 SQMM MULTIST. FRLS CU MR 216Same as as above item but supply, laying, and commissioning of wiring 3x10sqmm FRLS multistranded copper wire in 40mm PVC conduit

Page 192

219 3X6 SQMM MULTIST. FRLS CU MR 154Same as above item but supply, laying, and commissioning of wiring 3x6sqmm FRLS multistranded copper wire in 40mm PVC conduit

220 FRLS MULTISTR. 1.5 SQMM COPPER MR 14Supply and laying through conduit FRLS multistranded PVC insulated (1100V)copper wire conforming to IS 694:1990 and of size 1.5 sqmm includingtermination etc. all complete. PVC Conduits to be paid for separately as perrelevant items.

221 FRLS MULTISTR. 2.5 SQMM COPPER MR 22Same as above item but size 2.5 sqmm

222 FRLS MULTISTR. 4.0 SQMM COPPER MR 34Same as above item but size 4.0 sqmm

223 FRLS MULTISTR. 6.0 SQMM COPPER MR 60Same as above item but size 6.0 sqmm

224 18 SWG PVC INSUL. COPPER WIRE MR 10Same as above item but for single core PVC insulated copper wire 18 SWG.

225 PVC CONDUIT MED. IS:9537-25MM MR 16Supply and laying rigid non-flame propagating medium duty PVC conduit 25 mmdia. conforming IS 9537(Part III) including all bends, clamps, joineries, fixing onthe wall etc. all complete

226 PVC CONDUIT MED. IS:9537-32MM MR 25Same as above item but 32 mm dia

227 PVC CONDUIT MED. IS:9537-40MM MR 34Same as above item but 40 mm dia

228 CEILING FANS 1400 MM SWEEP EA 2065CEILING FANS Supplying and fixing of the ceiling fans of Crompton/GE/Polarwith detail as below : Sweep :1400 mm, Colour :White, Bearing type:Double ball bearing, Down Rod : Clear 300 mm long, Regulator :Electronic type ANCHOR/MK make, Accessories : Screws, wall nuts etc.

Supply, fixing and commissioning of Exhaust fans of following dia includingbird louvers, frame works and other civil works like chipping and making thesurface good etc

229 EXHAUST FANS 305MM DIA EA 1720230 EXHAUST FANS 230MM DIA EA 1540231 1x36W TUBE LIGHT FITTING EA 1800

Supply, fixing and commissioning of box type light fitting Philips make cat no.TMC501/136 HPF (High Power Factor) 1 x 36 W tube light fitting with lamp orequivalent of Crompton make Cat. DJB 14. Rate to include all accessories,interconnection of wires from ceiling rose to the fittings and fluorescent tubelamps , copper ballast etc.

232 1x60W SPOT LIGHT FITTING EA 11851 x 60W spot light luminaire with 1 meter track including lamp Philips make catno. DGN 451 or equivalent for display shelving

233 1x60W BULK HEAD FITTING EA 6201 x 60 W Bulk head luminaire including lamp Phillps cat no. NXC 101 orequivalent Crompton make:CBHE 29 ( Outside building).

234 ANGLE HOLDER WITH 60W LAMP EA 62Providing & fixing in position Angle holder Anchor make including lamp 60W

(Toilets).235 1x36W TUBE LT. FIT. TMS 21/136 EA 820

Page 193

1 x 36 W tube light fitting including lamp Phillps cat no TMS 21/136 HPF orequivalent ( stores, service area)

236 2x36W TUBE LIGHT FITTING EA 27952 x 36 W tube light fitting including lamp Phillps cat no TBS 50/236 HPF orequivalent (for false ceiling area)

237 2x36W INDOOR DECORATIVE LIGHT EA 19952 x 36 W INDOOR DECORATIVE 'Flatlite' luminarie including holding down rod,lamp, etc., complete of Philips make Cat. No. TCx20/236 HPF or equivalent.

238 MIRROR OPTIC FTG.-TCS605/236M1 EA 1900Same as above item but 2 x 36 W indoor decorative surface mounted tube lightfitting including lamp Philips cat no TCS 605/236 M1 HPF (High Power Factor)or equivalent of Crompton make Cat. CBSW 1124 HSB.

239 MIRROR OPTIC FTG.-TBS300/418M1 EA 2650Same as above item but 4 x 18 W indoor decorative mirror optics luminairesuitable for recessed mounting including 4 nos. TL D lamps Philips cat no TBS300/418 M1 HPF (High Power Factor) or equivalent of Crompton make Cat.CRFN 42 HSB.

240 CORNER LUMINAIRE-ACW/N- 1X18W EA 950Same as above item but Corner/wall slim (corner luminaire with lamp, reflectorclear receded acrylic cover Arcade make). 1X18W

241 CORNER LUMINAIRE-ACW/N- 1X36W EA 1040Same as above item but Corner/wall slim (corner luminaire with lamp, reflectorclear receded acrylic cover Arcade make). 1X36W

242 DECORATIVE LUMINAIRE-AMA-1X18W EA 939Same as above item but Decorative luminaire with lamp reflector, opal/clearreceded acrylic cover Arcade make. 1X18W

243 DECORATIVE LUMINAIRE-AMA-1X36W EA 875Same as above item but Decorative luminaire with lamp reflector, opal/clearreceded acrylic cover Arcade make. 1X36W

244 ENERGY ESSENTIALS- 11 W EA 145Same as above item but supply and fixing energy essential CFLs 11 W ofPHILIPS make. Approved equivalent - Havell/ Osram

245 ENERGY ESSENTIALS- 14 W EA 160Same as above item but supply and fixing energy essential CFLs 14 W ofPHILIPS make. Approved equivalent - Havell/ Osram

246 ENERGY ESSENTIALS- 18 W EA 189Same as above item but supply and fixing energy essential CFLs 18 W ofPHILIPS make. Approved equivalent - Havell/ Osram

247 SURFACE MOUNTED LUMINARE TCS 30 EA 1990Providing and fixing light fixtures Surface Mounted Lumonaire Philips TCS 306or approved equivalent from GE/BAJAJ/CROMPTON including lamp and otherallied accessories.

248 SURFACE MOUNTED LUMINARE CFL FC EA 1850Providing and fixing light fixtures Surface Mounted Lumonaire Philips CFL FCS518 LOTUS or approved equivalent from GE/BAJAJ/CROMPTON includinglamp and other allied accessories.

249 FBS 300 P5 RECESS MOUNTED EA 600providing and fixing light fixtures Recess Mounted Lumonaire Philips FBS 300P5 or approved equivalent from GE/BAJAJ/CROMPTON including lamp andother allied accessories.250 TEL. SOCKET POINT 2 PAIR MT 45

Page 194

TELEPHONE SOCKET POINT Supply and laying 2 pairs of 0.5 mm diascreened and shilded telephone wire in 20 mm dia PVC conduit partly/fullyconcealed in types of walls , floor etc complete with all accessories , wiringterminations, connected civil works, rough plastering etc including supply of 16GI fish wire conduit & accessories etc.

251 TEL. TAG BLOCK 5 PAIRS EA 720Supply, fixing and commissioning of ffive pairs of telephone tag block of Kronetype enclosed in suitable MS box. Rate shall include all accessories, connectedcivil works for fixing the same as per specifications.

252 TEL. SOCKET EA 450Supply and installation of modular type telephone socket MK make in a suitablesize box concealed to wall including all civil works

253 METER BRD (PART-C EX. ELECT.) EA 6150Supply and fixing of wall mounting type meter board made out of 16 SWG

CRCA sheet steel and single iron with 3 nos 200A Fuse cutouts N.L ,1 no. earthlink , 1 no neutral link and space for accommodating 1 no. 3 ph, 4 wire KWHmeter complete with adequate size of copper wire interconnections, powdercoating etc. complete.

254 PNL BRD-300ATPN 2X125/3X63/6X32A EA 78000Supply and erection, testing commissioning of floor mounting type cubical panelboard made out of 16 SWG CRCA sheet steel with 300 A TPN copper bus bars,interconnections, earthing, powder coating and comprising of the followings asrequired. Incomer : 2 nos 125A TP switch fuse unit with HRC fuses for DG andEB with interlocking 1 no.125A TP bus coupler/2 nos.volt meter with volt meterselector switch/2 no ammeter with CT & Ammeter selector switch/2 sets ofPhase indicating lamp (RYB)//Outgoings : 3 nos 63A and 6 nos 32A TP fuseswitch unit with HRC fuse/5KVAR capacitor : 2 nos. 255 FLR.MNT.PANELBOARD-2X125 2X63A EA 69386Supply and erection, testing commissioning of floor mounting type cubical panelboard made out of 16 SWG CRCA sheet steel with 200 A TPN copper bus bars,interconnections, earthing, powder coating and comprising of the followings asrequired. Incomer : 2 nos 125A TP switch fuse unit with HRC fuses for DG andEB 1 no 125A 4 pole change over switch 2 no volt meter with volt meter selectorswitch, 2 no ammeter with C T & ammeter selector switch, 2 sets of Phaseindicating lamp (RYB) Outgoing : 2 nos 63A and 3 nos 32A TP fuse switch unitwith HRC fuse/5 KVAR capacitor: 1 no.256 FLR.MNT.PANELBOARD-2X63/4X32A EA 55000Same as above item but with following details Incomer : 2 nos 63A TP switchfuse unit with HRC fuses for DG and EB 1 no 63A 4 pole change over switch 2no volt meter with volt meter selector switch, 2 no ammeter with C T & ammeterselector switch, 2 sets of Phase indicating lamp (RYB) Outgoing : 4 nos 32ATP fuse switch unit with HRC fuse with HRC fuse 5 KVAR capacitor : 1 no .

257 PNL BRD-Inc.2X63,Outgo1X63/3X32A EA 39500Same as above but with following details:- Incomer :2 nos 63A TP switch fuseunit with HRC fuses for DG and EB/1no. 63A 4 pole change over switch (online)/2 no volt meter with volt meter selector switch/2 no ammeter with CT &ammeter selector switch/2 sets of Phase indicating lamp (RYB)//Outgoings : 1no 63A and 3 nos 32A TP fuse switch unit with HRC fuse 5 KVAR capacitor : 1no 258 HENSEL -LT PANEL 25 KVA EA 96936

Page 195

Design, fabrication, supply, installation, testing and commissioning of factorymade LT switch board/ panel of Make - HENSEL made out of polycarbonate,polyestrene thermoplastic modules/enclosure with IP 65 degree of protection.Please refer to attched specifications, list of items, bill of materials and drawingnos. HENMIPDB31705 for details. Approved Equivalent - Fybox, Rittal

Bus Bar Rating: 250 A (12x10, 12x5 mm Cu), System Voltage: 415 V, 50 HzIncomer: 125A FP COS - 1No.; 100A TPN SFU - 1No.; 70A Contactor - 1No.Outgoings: 32A FP ISOLATOR - 1 No.; 32A FP MCB - 2 Nos.; 20A DP MCB -2 Nos.; 32A DP MCB - 14 Nos.; 10A DP MCB - 17 Nos.; 40A FP ISO - 1 No.

Metering: Voltmeter with selector switch (0-500V) - 1 No.; Ammeter with selectorswitch (0-63A) - 1 No.; Frequency Meter - 1 No.; Current Transformer(63/5A) - 3Nos.; R/Y/B LED Indication - each 1 No.; On/Off PB - each - 1 no.; Control Fusewith Base - 6 Nos. Terminals: 50 Sqmm Feed in Terminals - 10 Nos.; 6 Sqmm - 85 Nos.; 4 SqmmEarth Terminals - 35 Nos. Rate to include approved front cable cover, pedestalframe with FRP lining and canopy as per manufacturer's specifications. Note: For any outlet having requirement of more than 25 KVA load, the panelhas to be separately designed using the above basic material of approvedmanufacturers. The payment shall be made separately basis the originalquotation received from manufacturer and approved by HPCL Engg.-in-Charge.

259 63A TPN MCB DB EA 6320Supply, installation and commissioning of 63A TPN MCB DB Incomer : 1 no 63A , 4 Pole MCB Outgoings : 18 nos, 10A/16A/20A SP MCBs

260 32A TPN MCB DB EA 4230Supply, installation and commissioning of 32A TPN MCB DB Incomer : 1 no 32A , 4 Pole MCB Outgoings : 12 nos, 10A/16A/20A SP MCBsSupply and laying following size PVC insulated, sheathed, armoured cable ofapproved make

261 3.5CX 120 SQMM AL CABLE MR 705Supply and laying 3.5 core X 120 sq mm size PVC insulated, sheathed,armoured aluminium cable of approved make

262 3.5 C X 95 SQMM AL CABLE MR 560Same as above but size 3.5 core X 95 sqmm

263 3.5CX 70 SQMM AL CABLE MR 410Same as above but size 3.5 core X 70 sqmm

264 3.5CX35SQMM AL CABLE MR 300Same as above but size 3.5 core X 35 sqmm

265 4CX16SQMM AL CABLE MR 230Same as above but size 4 core X 16 sqmm

266 4CX6SQMM AL CABLE MR 130Same as above but size 4 core X 6 sqmm

267 4CX2.5SQMM COPPER CABLE MR 145Supply and laying 4 core X 2.5 sq mm size PVC insulated, sheathed, armouredcopper cable of approved make

268 3CX2.5SQMM COPPER CABLE MR 132Same as above but size 3 core X 2.5 sq mm

269 2CX2.5SQMM COPPER CABLE MT 110Same as above but size 2 core X 2.5 sq mm

270 4CX1.5SQMM COPPER CABLE MT 130Same as above but size 4 core X 1.5 sq mm

Page 196

END TERMINATION End termination of following cable with doublecompression NFLP gland and crimping sockets

271 3.5CX120SQMM AL CABLE END TER EA 140End termination of cable. Approved make Broco/Dowells/Commet/Cosmos

272 3.5CX95 SQMM AL CABLE END TER EA 120Same as above but for size 3.5 core X 95 sqmm

273 3.5CX70 SQMM AL CABLE END TER EA 110Same as above but for size 3.5 core X 70 sqmm

274 3.5CX35SQMM END TERMINATION EA 75Same as above but for size 3.5 core X 35 sqmm

275 4CX16SQMM END TERMINATION EA 65Same as above but for size 4 core X 16 sqmm

276 4CX6SQMM END TERMINATION EA 58Same as above but for size 4 core X 6 sqmm

277 4CX2.5SQMM END TERMINATION EA 55Same as above but for size 4 core X 2.5 sqmm

278 3CX2.5SQMM END TERMINATION EA 46Same as above but for size 3 core X 2.5 sqmm

279 2CX2.5SQMM END TERMINATION EA 55Same as above but for size 2 core X 2.5 sqmm

280 4CX1.5SQMM END TERMINATION EA 68Same as above but for size 4 core X 1.5 sqmm

281 3CX2.5SQMM END TER. DOB. COMP. EA 165End termination of cable for size 3 Core X 2.5 sq mm with double compressionNFLP gland and crimping sockets. Approved makeBroco/Dowells/Commet/Cosmos

282 2CX2.5SQMM END TER. DOB. COMP. EA 140End termination of cable for size 2 Core X 2.5 sq mm with double compressionNFLP gland and crimping sockets. Approved makeBroco/Dowells/Commet/Cosmos

283 4CX1.5SQMM END TER. DOB. COMP. EA 108End termination of cable for size 4 Core X 1.5 sq mm with double compressionNFLP gland and crimping sockets. Approved makeBroco/Dowells/Commet/Cosmos

284 CABLE TRENCH EXCAVATION MT 95Excavation in any type of soil including WBM/asphalt up to 600mm depth and300mm wide including supply and laying 150mm thick sand on top and bottomof cable, supply and laying bricks laid flat on top, back filling trench etc.complete.

285 JUNCTION BOX EA 1030Supplying and fixing flame proof and weather proof junction box of Sudhir /Baliga make out door junction box of IP 54 category of protection with rubbergasket and having locking arrangement including all required connectors, 10ASPMCB.

286 SINGLE ARM MS POLES EA 9962MS POLES Supply, Fabrication Erection of 7 mtrs high MS Pole having a baseplate of size 300x300x16 with 1000 mm long 40mm MS pipe suitable formounting 1 no. fixture as per attached detail specificaton. Job also includesfoundation for the same. Pole to be made up of 100mm dia MS pipe of 3.0 mlength, 80mm dia MS pipe of 3.0m length and 50mm dia pipe of 1.0m lengthwith 65mm dia cap, gusset plats, etc.,complete. Rates to include excavation,PCC, RCC and reinforcement, etc. complete287 DOUBLE ARM MS POLES EA 10250

Page 197

Same as above but with double arm288 OCTAGONAL GALVANIZED POLE 6.0 M. HT-SIN EA 12350

Supply and installation of BAJAJ make Hot dip galavanised iron pole of Height6.0 meter having wall thickness 3 mm. C/s A/F - top = 70mm, bottom =130 mm,base plate 220x220x12 mm, 500 mm long weatherproof reinforced door openingwith junction box mounting arrangement but exclusive of junction box, singlearm bracket 1 m, 20mm dia. threaded made to J shape and having 600 mmtotal length steel grade EN8 foundation bolts - 4 nos with nuts, templates and allcomplete as per approved drawing. Approved Equivalent Make - PHILIPS

Foundation RCC 1:1.5:3 shall be of size 550x550mm and depth 1200 mm with 8nos. 12mm dia. tor bars as main bars and 8mm dia. tor bars stirrups @ 190 mmc/c as per approved drawing. This reinforcement shall conform to IS:1786 latestedition. The foundation shall extend above sorrounding ground/driveway level for200 mm and have slant 63mm dia. PVC sleeve cast insitu foundation for cableentry as per the drawing. Rates to include excavation, PCC, RCC andreinforcement, etc. complete

289 OCTAGONAL GALVANIZED POLE6.0 M. HT-DOUB EA 13200Supply and installation of BAJAJ make Hot dip galavanised iron pole of Height6.0 meter having wall thickness 3 mm. C/s A/F - top = 70mm, bottom =130 mm,base plate 220x220x12 mm, 500 mm long weatherproof reinforced door openingwith junction box mounting arrangement but exclusive of junction box, doublearm brackets 1 m each, 20mm dia. threaded made to J shape and having 600mm total length steel grade EN8 foundation bolts - 4 nos with nuts, templatesand all complete as per approved drawing. Approved Equivalent Make -PHILIPS

Foundation RCC 1:1.5:3 shall be of size 550x550mm and depth 1200 mm with 8nos. 12mm dia. tor bars as main bars and 8mm dia. tor bars stirrups @ 190 mmc/c as per approved drawing. This reinforcement shall conform to IS:1786 latestedition. The foundation shall extend above sorrounding ground/driveway level for200 mm and have slant 63mm dia. PVC sleeve cast insitu foundation for cableentry as per the drawing. Rates to include excavation, PCC, RCC andreinforcement, etc. complete

290 GI OCT POLE-SNGL ARM 7M EA 13400Supply and installation of BAJAJ make Hot dip galavanised iron poleof Height7.0 meter wall thickness 3 mm. C/s A/F - top = 70mm, bottom =130 mm, baseplate 220x220x12 mm, 500 mm long weatherproof reinforced door opening withjunction box mounting arrangement but exclusive of junction box, double armbrackets 1 m each, 20mm dia. threaded made to J shape 700 mm long steelgrade EN8 foundation bolts - 4 nos with nuts, templates and all complete as perapproved drawing. Approved Equivalent Make - PHILIPS.

Foundation RCC 1:1.5:3 shall be of size 550x550mm and depth 1400 mm with 8nos. 12mm dia. tor bars as main bars and 8mm dia. tor bars stirrups @ 190 mmc/c as per approved drawing. This reinforcement shall conform to IS:1786 latestedition. The foundation shall extend above sorrounding ground/driveway level for200 mm and have slant 63mm dia. PVC sleeve cast insitu foundation for cableentry as per the drawing. Rates to include excavation, PCC, RCC andreinforcement, etc. complete.

Page 198

291 GI OCT POLE-DBLE ARM 7M EA 14500Same as above but for Double Arm

292 GI OCT POLE-SNGL ARM 8M EA 15500Supply and installation of BAJAJ make Hot dip galavanised iron pole of Height8.0 meter wall thickness 3 mm. C/s A/F - top = 70mm, bottom =135 mm, baseplate 225x225x16 mm, 500 mm long weatherproof reinforced door opening withjunction box mounting arrangement but exclusive of junction box, singler armbracket 1 m, 20 dia threaded made to J shape 750 mm long steel grade EN8foundation bolts - 4 nos with nuts, templates and all complete as per approveddrawing. Approved Equivalent Make - PHILIPS.

Foundation RCC 1:1.5:3 shall be of size 550x550mm and depth 1500 mm with 8nos. 12mm dia. tor bars as main bars and 8mm dia. tor bars stirrups @ 190 mmc/c as per approved drawing. This reinforcement shall conform to IS:1786 latestedition. The foundation shall extend above sorrounding ground/driveway level for200 mm and have slant 63mm dia. PVC sleeve cast insitu foundation for cableentry as per the drawing. Rates to include excavation, PCC, RCC andreinforcement, etc. complete.

293 GI OCT POLE-DBLE ARM 8M EA 16000Same as above but for Double Arm

294 STREETLIGHT FITTING CRP330/250 EA 7500Supply and fixing Philips make Cat. CRP 330 street light fixture (IP65) withCeramic Discharge CDMTT 250W lamp (Make Philips/ Osram) and single piecedie cast aluminium housing with all accessories energy efficient copper ballast,heat resistant toughened flat glass cover, electronic ignitor, reflector' powerfactor improvement capacitor etc. complete. Approved equivalent of Bajaj makeAqua Wave Series Cat. BGWRL 250 MH SE FFG with 250 W CeramicDischarge CDMTT lamp and approved equivalent of Crompton makeMHSGT1215IH/G with Lamp 250WCDM-TT . Approved equivalent of WIPROmake cat no: WST 25250 1X250 W. The job includes fixing the street lightfixtures, providing flexible wire of 7/20 copper wire of approved make, fromjunction box to top of the pole.

295 HOARDING LIGHT QVF 135/70 EA 3950Supply and fixing Philips make Cat. QVF 135 hoarding light fixture (IP54) withMetal Halide MHN-TD 70W lamp, control gear box, light weight corrosion-resistant pressure die cast housing with universal mounting bracket, allaccessories energy efficient copper ballast, heat resistant toughened glasscover, electronic ignitor, reflector, power factor improvement capacitor etc.complete. Approved equivalent Crompton make Cat. TH 6 MH(DE). The jobincludes fixing the street light fixtures and wiring as approved.296 FIXING OF STREET LIGHT FITTING EA 459Fixing of street light fixture including providing flexible wire from junction box totop of the pole

297 EARTHING PIT-PLATE ELECTRODE EA 7560

Page 199

Providing plate electrode earthing as per IS 3043 and attached drawing includingexcavation of depth 3.2 m, supplying and fixing plate electrode of size 600x600mm and thickness 6.3 mm (GI) or 3.15 mm (Copper), 50mm dia GI pipe ofheavy duty (wall thickness 4.5 mm) with funnel for watering, wire mesh, GI flat (2nos. 50x6 mm ) collars, two connecting GI strips (50x6 mm) from plate electrodeto collar, fixing & using using GI nut bolts with bitumen coating and welding asper drawing, filling the pit with alternate layers of charcoal and salt, back filling,constructing 230 mm thick Brick Masonry chamber1000(length)x500(width)x600 (depth) mm internal size with plastering 10 mmthick and embedded 50 mm dia PVC conduit openings at two places packedwith jute soaked in bitumen at the entrances, 100mm thick PCC 1:3:6 at thebottom of chamber, providing 3 mm thick MS sheet cover with diagonal bracingsof 25x3 mm flats, frame and hinge arrangement covering full opening, groutingRate includes carrying out earth resistance testing of the earth pit provided,submitting report and painting resistance, test date and pit identification no. oncover top.

298 PLT ERTH W/O CHAMBER&COVER EA 3250Earthing Pit-Pipe Electrode without chamber:Same as ABOVE item but without chamber and covers. The item is for providing earthing pit under driveway. Thechamber and cover shall be provided with same specifications as of drivewaychambers and as per instructions of Engg.-In-Charge. The driveway chambersshall be paid as per respective item rate.299 EARTHING PIT- PIPE ELECTRODE EA 6800Providing pipe electrode earthing as per IS 3043 and attached drawing includingexcavation of depth 3.75 m, supplying and fixing pipe electrode of size 50 mmdia heavy duty (wall thickness 4.5 mm) GI pipe with funnel for wateing, wiremesh, GI flat (50x6 mm) collar joined to pipe using 50x6 mm strip and GI nutbolts with bitumen coating as per drawing, filling the pit with alternate layers ofcharcoal and salt, back filling, constructing 230 mm thick Brick Masonrychamber 400(length)x400(width)x400 (depth) mm internal size with plastering10 mm thick and embedded 50 mm dia PVC conduit openings at two placespacked with jute soaked in bitumen at the entrances, 100mm thick PCC 1:3:6 atthe bottom of chamber, providing CI cover with CI frame in hinge arrangementcovering full opening, grouting the cover frame in PCC 1:2:4 bed 230x75 mm,painting two coats of approved colour synthetic enamel paint over a coat of redoxide primer etc. complete. Rate includes carrying out earth resistance testing of

300 PIPE ERTH W/O CHAMBER&COVER EA 3900Earthing Pit-Pipe Electrode without chamber:Same as ABOVE item but without chamber and covers. The item is for providing earthing pit under driveway. Thechamber and cover shall be provided with same specifications as of drivewaychambers and as per instructions of Engg.-In-Charge. The driveway chambersshall be paid as per respective item rate.301 NAME PLATE FOR EARTH PIT EA 425Proding/Fixing of MS name/ID plate for earthing pit including painting etc as perthe prevailing norms of IS/BIS / as per the direction of EIC. Size300mmX200mm and 1.2 mm thick with MS flat/square bar for grouting.

302 10 SWG COPPER WIRE MT 66Supply and fixing 10 SWG copper wire for earthing connection to pumps,canopy columns etc.

303 GI FLAT-50X6 MM MT 325Supply and fixing 50x6 GI flat for earth connection of panel / interconnection ofearth pits.

304 GI FLAT - 25X6 MM MT 175

Page 200

Supply and fixing 25x6 GI flat for earth connection 305 GI FLAT-25X3MM MT 95

Supply and fixing 25x3 GI flat for earth connection 306 CU FLAT -25X3MM MT 350

Supply and fixing 25x3 GI flat for earth connection 307 MS CHEQURED PLATE KG 59

Providing and fixing 6mm thick MS chequered plate including making holdingarrangements, painting with two coats of red oxide primer and two coats ofsynthetic enamel paint etc.

308 MS CHANNEL/ANGLE EDGE PROTN. KG 55Providing and fixing MS angle/channel supports and edge protection for trenchetc. including providing hold fast ,painting with two coats red oxide primer andtwo coats of synthetic enamel etc.

309 3CX1.5SQMM COPPER WIRE MT 53Supply, laying of PVC insulated, unsheathed multistranded, FLRs copper wirethrough PVC conduits or on walls with saddling etc., complete.Size 3Core X 1.5sqmm

310 2CX1.5SQMM COPPER WIRE MT 50Same as above but size 2 Core X 1.5 sq mm

311 4CX2.5SQMM COPPER WIRE MT 68Same as above but size 4 Core X 2.5 sq mm

312 5PAIR TEL WIRE MT 75Supply and laying of 5 pair telephone wire of approved make

313 CO-AXIAL CABLE MT 82Supply and laying of co-axial cable of approved makePVC CONDUITS HEAVY DUTY Supply and fixing of heavy duty PVC conduitsof following dia approved make including all accessories like PVC sockets,bends, junction boxes, etc., joining by using proper solution, saddling, clamping,etc, complete.314 25MMDIA HEAVY DUTY PVC CONDUIT MT 25PVC CONDUITS HEAVY DUTY Supply and fixing of heavy duty PVC conduits ofsize 25 mm diameter approved make including all accessories like PVC sockets,bends, junction boxes, etc., joining by using proper solution, saddling, clamping,etc, complete.

315 32MMDIA HEAVY DUTY PVC CONDUIT MT 35Same as above but size 32 mm diameter

316 40MMDIA HEAVY DUTY PVC CONDUIT MT 39Same as above but size 40 mm diameter

317 SINGLE POLE MCB EA 174MCB Supply and fixing of single pole MCB of approved make from 6 to 32 Ampsincluding providing and fixing metal boxes, termination, etc, complete.

318 DOUBLE POLE MCB EA 383MCB Supply and fixing of double pole MCB of approved make from 6 to 32Amps including providing and fixing metal boxes, termination, etc, complete.

319 TRIPLE POLE MCB EA 717MCB Supply and fixing of triple pole MCB of approved make from 6 to 32 Ampsincluding providing and fixing metal boxes, termination, etc, complete.

320 METAL HALIDE LIGHT EA 5428

Page 201

Supply and fixing of 150W metal halid canopy light fixtures with lamp and allaccessories like choke, gearbox, ignitor etc, and mounting the same on falseceiling etc., complete. Wipro Cat. Code WCT15150 or equivalent.

321 ISI MARKED RUBBER MAT-12MM SM 902Supply and fixing 12mm thick ISI marked rubber mat of approved make.

322 CVCF -15 KVA EA 164791Supply , installation and commissioning of 3 phase AIR cooled balanced /unbalanced load Constant Voltage Constant Frequency Volatge Stabilizers(Make - Logicstat / Blue bird / Bhurji / Techno Vision / Numeric or HPCLapproved make) including auto / manual control, overload trip relay, low / highvoltage cut-off, single phase protector, cost of oil. Rate includes making inputand output connection but excludes supply of necessary cables, lugs andclamping. Party to furnish manufacturer's test certificate alongwith supply andprovide warranty/gaurantte for a period of one from the date of installation. Input freq range 45 Hz to 55 HzAccurate output voltage 240vac +/-3% line - neutralAccurate output freq 50Hz+/-0.1% (crystal controlled)Output power factor 0.8 lagging to UnityDC Bus Voltages 360 VDC to 408 VDCUnmatched transient response For 100% step load change output stays within +/-5% and recovers within 5 msecs.Latest technology Micro- controller based PWM, IGBTOutput waveform Pure sine waveOutput overloading : 100% continuous, 120% 15mins, 150% 30secsCrest factor 5:1 suitable for inductive load like motors.Inverter efficiency Greater than 90%Transfer time Continuous inverter “on” no change overtimeOperating temp 0 TO 55 deg CHumidity range 95% Rh (non condensing)Total harmonic distortion Less than 2% at linear load less than 5% at non-linear loadIsolation Total isolation of output from input to protect from spicks and surgesGenset compatible : YesAlarms warning Mains fail, Batt low, DC over, DC under, o/p AC over, O/p over load, O/p AC under User friendly monitoring Indication: Mains on, Inverter On, Batt. Low, Inv trip, BypassAudible noise Less than 60 db at 1 meterBy pass Manual bypass providedBattery charger Charger is designed on CVCC principle to keep batteries in long DC over/under voltage, Input phase fail

323 3 PHASE SERVO STABILISER-40 KVA EA 116323Supply , installation and commissioning of 3 phase AIR cooled balanced /unbalanced load servo controlled voltage stabiliser of 40 KVA (Make - Logicstat /Blue bird / Bhurji / Techno Vision or HPCL approved make) including auto /manual control, overload trip relay, low / high voltage cut-off, single phaseprotector, cost of oil. Rate includes making input and output connection butexcludes supply of necessary cables, lugs and clamping. Party to furnishmanufacturer's test certificate alongwith supply and provide warranty/gauranttefor a period of one from the date of installation. Detailed specifications are as

Page 202

Specifications 3 Phase1. Input Voltage 300 - 460 VAC2. Output Voltage 415 VAC3. Operating frequency 50 HZ4. Output Voltage Regulation +/- 1%5. Response time < 3 msecs6. Rate of Correction 12 to 60 V / Sec7. Efficiency > 98%8. Wave form Distortion Nil9. Effect on Power Factor Nil10. Operating Temperature 10 – 60 Degree C11. Duty of operation Continuous at 100%12. Cooling Forced Air Cooling PROTECTIONSUNDER / OVER VOLTAGE Contactor/MCCBShort Ckt Over Load Protection MCB/ MCCBSingle Phasing Preventer Not requiredNeutral Lift Protection OptionalEMI/RFI filters OptionalBy Pass Switch Required rotary bypassINDICATIONMains On RequiredUnder/Over Voltage RequiredVoltmeter 0 – 500 VACAMP meter RequiredAlarm Optional OptionalOutput voltage setting It should be possible to set the output voltage from thefront panel

324 3 PHASE SERVO STABILISER-30 KVA EA 101783Same as above but rating 30KVA

325 3 PHASE SERVO STABILISER-25 KVA EA 92089Same as above but rating 25KVA

326 3 PHASE SERVO STABILISER-20 KVA EA 72702Same as above but rating 20KVA

327 3 PHASE SERVO STABILISER-15 KVA EA 53315Same as above but rating 15KVA

328 3 PHASE SERVO STABILISER- 10 KVA EA 38774Same as above but rating 10KVA

329 1 PHASE SERVO STABILISER- 10 KVA EA 33928Supply , installation and commissioning of 1 phase AIR cooled balanced /unbalanced load servo controlled voltage stabiliser of rating 10 KVA (Make -Logicstat / Blue bird / Bhurji / Techno Vision /Numeric or HPCL approved make)including auto / manual control, overload trip relay, low / high voltage cut-off,single phase protector, cost of oil. Rate includes making input and outputconnection but excludes supply of necessary cables, lugs and clamping. Party tofurnish manufacturer's test certificate alongwith supply and providewarranty/gaurantte for a period of one from the date of installation. Detailedspecifications are as under:

Page 203

Specifications 1 Phase1. Input Voltage 170 – 270VAC2. Output Voltage 230 VAC3. Operating frequency 50 HZ4. Output Voltage Regulation +/- 1%5. Response time < 3 msecs6. Rate of Correction 12 to 60 V / Sec7. Efficiency > 98%8. Wave form Distortion Nil9. Effect on Power Factor Nil10. Operating Temperature 10 – 60 Degree C11. Duty of operation Continuous at 100%12. Cooling Air Cooling PROTECTIONSUNDER / OVER VOLTAGE REQUIREDOver Load Protection MCBINDICATIONMains On RequiredUnder/Over Voltage RequiredVoltmeter 0 – 300 VACAMP meter OptionalAlarm Optional

330 1 PHASE SERVO STABILISER- 7.5 KVA EA 24234Same as above but rating 7.5 KVA

331 1 PHASE SERVO STABILISER-5 KVA EA 17448Same as above but rating 5 KVA

332 1 PHASE SERVO STABILISER-3 KVA EA 12602Same as above but rating 3KVA

333 1 PHASE SERVO STABILISER-2 KVA EA 9209Same as above but rating 2 KVA

334 250 VA CVT EA 3005CVT Supply and fixing of constant voltage transformer of aproved make -

Logicstat, Blue bird, Sukam, Bhurji , Numeric or equivalent. Party to furnishmanufacturer's test certificate alongwith supply and provide warranty/gauranttefor a period of one year from the date of installation. Rating 250 VA rating

Page 204

CVT Technical SpecificationsInput Voltage 180 to 260V AC/1 Ph/50±2HzOutput Voltage 220VAC/230VAC±1%Frequency Effect Approx. 1.5% change in output voltage, for 1% change in inputfrequencyEfficiency 90%, Typical, at full loadCommon-Mode-Noise Attenuation* 1:3000, Typical Normal-Mode-Noise Attenuation* 1:2500, Typical Output waveform SinusoidalTotal Harmonic Distortion 5% (Typical) at 230VAC-Input & full-load changeOutput Voltage Correction 2 cycle (max.) for no load to full load conditionsOver Load protection To be providedOperating Temperature 0ºC to +50ºCOperating Humidity 95% RH, non condensingMetering 0-300v, M.I. meter; Accuracy ± 2% FSD (To monitor output voltage)Environment 0-40°C, 95% RH (non condensing)

335 500 VA CVT EA 4508Same as above but rating 500 VA

336 750 VA CVT EA 7561Same as above but rating 750 VA

337 1000 VA CVT EA 9984Same as above but rating 1000 VA

338 1500 VA CVT EA 14201Same as above but rating 1500 VA

339 2000 VA CVT EA 19193Same as above but rating 2000 VA

340 GSB LAYER SM 263Filling material with GSB (Granular Sub Base) of 30 cm thick:: The GSB shallconsists of the following material 40 to 53MM Size metal : 40%20 to 40MM size metal 20%10 to 20MM size metal 20% 0 to 10MM size metal 20%Job shall include supply and filling GSB materials in two compacted layers of150 MM each. Payment shall be released on the compacted layer provided bythe vendor at site. Compaction shall be carriedout only with Vibro roller ofrequired capacity . Contractor has to obtain necessary clerance from HPCL orits autorised reprensatative for first layer. Only after obtaining the second layerGSB shall be provided. Job includes all me material and transporation cost ofthe required to be completed as per the directions of the HPCL

341 WBM 1ST LAYER 100 mm thk. SM 107WATER BOUND MACADUM Providing and laying WBM in 100mm thickcompacted thickness each using well graded stone aggregates of approvedquality of 90 to 45 mm size with screening of 13.2 mm & less. Rate includesspreading metals, hand packing, filling the interstices with spalls, chips, andapproved quality binder and rolling each layer with 10 MT power roller withsimultaneous watering till the metal is bound by the water binder paste toachieve maximum compaction, finishing the surface to

Page 205

proper grade and level .Rate also to include carrying out the following tests onaggregates and test results to be submitted to EIC before use and shall meetfollowing strength requirements.[LA Abrasion value : 40 % , Flakiness Index :15%]342 WBM 2ND LAYER 75 mm thk. SM 80Second Layer 75 mm thick using 63 to 40mm size stone aggregate withscreening of 13.2 mm & less.

343 WBM 3RD LAYER 75 mm thk. SM 80Third layer of 75mm thick using 53 to 22.2 mm size stone aggregate withscreening of 13.2 mm & less

344 SEMI DENSE BITU.CONC. 25MM THK SM 263SEMI DENSE BITUMINOUS CONCRETE (25 mm Thick) : Providing and laying25 mm thick semi dense bituminous concrete on prepared surface with goodquality graded stone aggregate as per following requirement -Material 5euiredper 100 Square meter Crushed stone aggregate of 13.2 mm size = 1.0 CUM ,11.2 mm size -1.6 CUM , Fine aggregate 6 mm size - 1.1 CUM Bitumen 60/70grade including tack coat = 330 Kg .The job includes hot mixing of aggregateand bitumen by using hot mix plant transportation mixed material and laying thesame , rolling with 8 to 10 Ton power roller to uniform consolidated compactedthickness of 25 mm over a tack coat of 2.0 Kg per 10 Square meter to achievethe required level and grade all material, labour etc complete.

345 SEMI DENSE BITU.CONC. 40MM THK SM 430SEMI DENSE BITUMINOUS CONCRETE (40 mm Thick) : Providing and laying40 mm thick semi dense bituminous concrete on prepared surface with goodquality graded stone aggregate as per following requirement: Material per 100Square meter Area - Crushed stone aggregate of 13.2 mm size = 1.60 CUM;11.2 mm size -2.56 CUM; Fine aggregate 6 mm size - 1.76 CUM; Bitumen 60/70grade including tack coat = 525 Kg .The job includes hot mixing of aggregateand bitumen by using hot mix plant transportation mixed material and laying thesame , rolling with 8 to 10 Ton power roller to uniform consolidated compactedthickness of 40 mm over a tack coat of 2.0 Kg per 10 Square meter to achievethe required level and grade all material , labour etc complete .

346 SEMI DENSE BITU.CONC.100MM THK SM 870SEMI DENSE BITUMINOUS CONCRETE (100 mm Thick) : Same as above butwith thickness of 100 mm.

347 MASTIC WEARING COARSE 25MM SM 700MASTIC WEARING COARSE (25 mm Thick): Providing and laying 25 mm thickmastic wearing coarse using stone aggregates as per following specs- Coarseaggregated to be used 35% of total mix , Balance shall be coarse sand and fillermaterial, Lime stone powder and industrial bitumen of grade85/25 confirming toIS 702 prepared by using Mastic cooker and laid to required level and slopeincluding providing anti skid surface with bitumen precoated fine grain chippingof 9.5 mm to 13.2 mm size at the rate of 0.005 CUM per 10 square meter ofapprox. spacing of 10 cm center to center in both directions , pressed intosurface protruding 1mm to 4 mm over mastic surface including cleaning thesurface removal of debris etc. material and labour complete. NOTE : Lime stonepowder shall have minimum calcium carbonate content of 80 %.

348 FIBRE REINFOR. CONCRETE COVER SM 3900

Page 206

Suppy and laying in posion of Precast slab shall be of FRC ( Fibre reinforcedCconcrete) of 20MT load bearing capacity, dimention 750X450x150 MM, with12mm dia plain round bar for lifting the cover fiited with plastic cups. The slabshalll be manufactured as per IS code: 12592 (part-1, 1988 & Part-2, 1991) andshall comply with following: requirements:Mechanised production through vibration pressing techniquesManufactured with concrete mix of minimum M 300 gradeTop surface of the cover shall be ebosed with checkered design for safetyagains hazards of slipping.Cover shall be designed to prevent jamming of covers in framesThe slabs shall be provided with lifting bars for easy handling duly protectedagainst currossion.Necessary Manufacturer test certificate, copy of invoice tec etc shall besubmitted by the vendor conformimg the above requirements

349 THERMOPLASTIC ROAD MARKING SM 950Supplying and applying Berger make Sigmark thermoplastic road marking paint(yellow in color) as per MORTH specifications 803.4. The work shall be carriedout strictly in line with maufacturer's procedures and using specified materials,tools, heating device/apparatus and machinery etc. all complete. The briefs ofmaterials are as following:(i) Hot Melt Thermoplatic Road Marking Compound: 5 kg/sqm(ii) Glass Beads: 250 gm /sqm

The drying time should be within 5 minutes and dry coat thickness to be 2.5 mm.Rate shall be inclusive of all material, labour, tools & tackles, power, heatingapparatus etc. all complete. Work shall be carried out ensuring safety at outletand as per approved drawing and plan.

350 RAISED PAVEMENT MARKERS SM 475Providing and fixing 3M make adhesive type heavy duty high performance raisedpavement markers with shanks (Glow Stubs) made of Engineering Polymer insize 101x89mm with height 20mm having retroreflective element on both sidesand to be fixed on cement concrete rigid pavement with adhesive/shanks asrecommended by manufacturer and interspacing as per Engg.-in-Chargeapproval. Rate includes necessary before/after cleaning, tools and tackles etc.all complete

351 LINEAR DELINEATION SHEETING SM 3790Providing and fixing 3M make Linear Delineation Sheeting (LDS) comprising ofpanels of size 4" wide and 33" length in yellow colour. The panel is to beconstructed of cube corner Retro Reflective Material bonded to Aluminiumsubstrate with memmed lateral edges. The panel assembly shall have arepeating raised lateral ridge every 2.25 inch, 0.34 inch in height. The typicalretro reflective values at 88.5 degree entrance angle / 0.2 degree observationangle to be 270, 162, 11080 (candelas/ meter square / lux) of yellow colour.

The fitting will be done on brick masonry/concrete walls as per manufacturerspecified procedures and approved nails/fixtures in line and level as per adviceof Engg.-in-Charge (EIC). Powder coated MS angle edge protection shall beprovided to make it theft resistant. Measurement and payment shall for per no.of 33inch long and 4" wide LDS provided as per EIC advice.

Page 207

352 MASTERTOP 1332 SM 2900Supplying, painting/laying Degussa make Polyurethane based multi –component decking system for heavy abraison areas including material,machinery, tools and tackles, power etc. all complete following manufacturerspecified procedures. The brief of constituent layers/coats are as following, thelast being the topmost layer: Mastertop 1332MTOP 1200 plus primer @ 0.3 kg / sqm; Mastertop SRA No. 3 sand scatter @0.6 kg/sqm; Mastertop Membrane 23 @ 0.5 kg/sqm; Mastertop SRA No. 3 sandscatter @ 1 kg/sqm and TWO COATS of Mastertop TC 458 of colour French/HPblue (Colour Code BS 166) @ 0.4 kg / sqm each coat i.e. total 0.8kg/sqm. Eachlayer will be given generally one day set period as per manufacturer'sspecifications. Traffic will not be allowed in the area from very first layerapplication till setting of top coat. It shall be vendor's responsibility to ensure thatproper application for each layer is done with sufficient time. In case the vendorfails in ensuring proper application and setting time, rectifications shall be done The vendor shall furnish 5 years repalcement guarantee on Rs.100/- stamppaper against defects, damage under vehicular traffic, wear and tear etc. fromthe completion date. HPCL descrition shall be final and binding on the vendor.

353 PREMIX CARPET-50 MM SM 280Providing and laying premix carpet 50 mm thick ( Consolidated) with coarseaggregate of nominal size 12.5 mm ( two part ) and 10 mm ( one part) . Quantityof bitumen (80/100 grade) used should be 36.5 Kg per 10 sqm for premix and7.5 kg per 10 sqm for tack coat. Surface preparation by cleaning with wire brush,removing the dust etc before applying tack coat. The job includes compaction by8 to 10 Ton roller to proper camber and slope all complete as per direction ofEngg.-In-Charge.

354 PREMIX CARPET-100 MM SM 433100mm thick carpet : Specification same as above item but two layers of 50mmthick each.

355 SEAL COAT 12 MM SM 145Providing and laying seal coat of 12 mm thick with 6.3 mm down coarseaggregate. Quantity of bitumen used should be 19.6 Kg per 10 square meter ofseal coat . The job includes compaction by 8 to 10 Ton power roller to propercamber and slope all complete as per direction of Engg.-In-Charge. Finishingshould be done by applying a layer of sand in order to fill up the voids.

NOTE : All the asphalting jobs shall be started only after stacking bitumen atthe site as per theoretical calculation considering the area. The total jobincluding seal coat to be carried out in one go. In case of any delay in laying theseal coat after laying the premix carpet, additional tack coat @ 5.0 Kg per 10sqm to be laid without any extra payment.

356 BBM SM 245Providing and laying bitumenous bound macadum surface 100 mm thick aftercompaction including supplying all materials spreading 40 mm size trap metallayers and key aggreagates heating and spraying bitumen of grade IS grade S-65 with penetration 60/70 at the rate of 400 kg/100 sqm and compacting afterfinishing by 6mm thick layer of grit to the satisfaction of the engineer with a rollernot less than 10 MT.

357 S/L DRIVEWAY GREY PAVER M-40 SM 610

Page 208

Supply and laying of 80mm thick grey pavers in line and level and approvedpattern and shape, as per attached specifications. The job includes supplyingand laying sand bedding, compacting using plate vibrator, all material and labourcomplete. Pavers will be laid in specified pattern. Plan of laying will be developedby the contractor and prior approval of EIC will be taken before commencementof laying. The pavers supplied should qualify min comp. strength conforming toIS:15658:2006. The party shall have to produce manufacturer's certification onthe paver qualifying criteria stated in IS-15658 and limits specified in theattached specification before the pavers are sited. HPCL reserves the right to dorandom sampling and testing as per IS-15658:2006 to assess manufacturer'scertification on qualifying norms specified in the attached specification. Thetesting charges, if samples qualify, shall be borne by HPCL, else shall be borneby the party.

358 S/L DR.WAY COLOUR PAVER M-40 SM 640Same as above but coloured paver

359 S/L REFL. GREY D/W PAVER M40 SM 640Same as above but reflective coloured paver. The top layer shall have 10to15mm uniform thickness made out of Granite/Quartz crushed aggregated ofcubical sizes not more than 6 mm & downsize (shall have good abrasionresistant properties) as wearing layer & reflective coating & cement shall bemixed with UV resistant pigment & colour as per HPCL's selection & withoutimpairing the characteristic properties of cement. Top surface shall be made antiskid (indentations) with lacquer coating finish.

360 S/L REFL. COLOURED D/W PAVER M40 SM 660Same as above but coloured paver

361 S/L GRASS PAVERS MIX M-40 SM 480Specifications same as item no. 434 but for grass pavers. Grass pavers shall beof 80 mm thickness and shape corner-cut square made out of 500x500 mm sizewith all the four corners cut in quarter size circles of 125 mm radius. Four nos. ofsuch pieces laid in symmetrical square pattern will give total opening area of0.196 sqm. The circular openings so formed shall be planted with grass. Supplyand laying of grass is not included in the scope but filling of these openingswith same sand fully compacted and vibrated is included in the scope. 362 S/L PEDESTRIAN PAVERS MIX M-25 SM 400Specifications same as item no. 434 but for 40 mm thick wedge wood (flag)unipavers made from M 25 grade concrete in 1 red and 2 grey combination forwalkways and light load areas as advised by EIC .

363 RELAYING OF PAVERS SM 50Laying of HPCL supplied/existing old pavers in line and level , as per attachedspecifications. The job includes supplying and laying sand bedding, compactingusing plate vibrator, all material and labour complete. Pavers will be laid at 45degree to road line in 1 red and 2 grey arrangement. Plan of laying will bedeveloped by the contractor and prior approval of EIC will be taken before

364 PRECAST KERB 300X150X450 M3 4300RCC PRECAST KARB 0.3X0.15X0.45: Providing and erecting kerb wall ofconcrete precast kerb of required size & shape with M20 grade concrete using20mm and down size crushed stone aggregates including shuttering, mixing,compacting , pond curing for 14 days etc. as per IS 456 with 100X100 size sunkof retro-reflective paint of approved shed as per the details, transporting from theplace of casting, errcting the wall with filling the joints with necessary cementslury etc. complete .

365 PRECAST KERB 300X150X300 M3 4300

Page 209

RCC PRECAST KARB 0.3X0.15X0.30 : Providing and erecting kerb wall ofconcrete precast kerb of required size & shape with M20 grade concrete using20mm and down size crushed stone aggregates including shuttering, mixing,compacting , pond curing for 14 days etc. as per IS 456, transporting from theplace of casting errcting the wall with filling the joints with necessary cementslury etc. complete .

366 TREMIX RCC 1:1.5:3 DRIVEWAY M3 5054Providing and laying 150mm/ 200 mm thick RCC driveway with 1:1.5:3 nominalmix using 20mm and down size crushed stone aggregates in panels usingslotted MS channel shuttering, machine mixing, vibrating with screed boardvibrator, pond curing for 14 days, vaccum dewatering, finished with powertrowelling. Concreting shall be carried out as per IS 456.

Rate shall also include providing approved quality polythene paper below thedriveway, constructing horizontal and longitudinal vatas with 1:10 CM forcuring, levelling depressions if any in the base with 20mm stone aggregates andstone dust.Proper slope to be provided in driveway for easy draining of rain water.Reducedlevel of the driveway area to be taken jointly with architect beforecommencement of concreting and after concreting and the thickness of RCC tobe checked.Testing of cube, reinforcement steel, stone aggregates, sand, cement etc. to be

carried out by contractor at no extra cost.Tubing, ducting, trenching and othernecessary embedded items in concrete shall be checked with architect/HPCLrepresentative before concreting.Grooves shall be cut in the RCC driveway andsame shall be filled with Bitumen at no extra cost.The cement consumption for 1:1.5:3 mix shall be 8.5 bags/cum andcompressive strength shall be 170 kg/sqcm and 200 kg/sqcm after 7 days and28 days respectively. Rate shall be excluding reinforcement steel whichshall be paid separately .

367 TREMIX WITH M-20 READY MIX M3 5500Same as above item but using M-20 grade ready mix concrete.

368 RCC 1:1.5:3 WITHOUT DEWATERING M3 4718Same as above item but without vaccum dewatering and power trowelling with1:1.5:3 nominal mix

369 TREMIX RCC DR.WAY-RAP HARD CEM M3 5215Same as tremix drive way item but with using rapid hardening cement for the1:1.5:3 mix

370 RCC PRECAST SLABS M3 5054Providing and laying RCC precast slabs of required size with 1:2:4 nominal mixusing 20mm and down size crushed stone aggregates including shuttering,mixing, compacting , pond curing for 14 days etc. as per IS 456, transportingfrom the place of casting . Reinforcent steel shall be paid separately.

371 RCC PRECAST COVER SM 2700Providing and laying factory made pre-cast RCC (Concrete Grade – MINIMUMM35) covers with MS lifting lugs of Surabh / KK manhole make having thickness90 mm and size to cover the pipeline trench. The cover shall be suitable for AAAclass load (Minimum 35 MT rolling axle load) and shall have MS enclosure ofminimum 2 mm thick allaround including reinforcement suitable for load class.The clear opening span of trench shall not be more than 650 mm.

Page 210

372 STEEL REINFORCEMENT TM 46000STEEL REINFORCEMENT Supply, fabrication and placing in position High yieldstrength deformed bars conforming to IS 1786 - Latest edition grade FE 415 asrequired and directed at site for driveway including cutting, bending, placing inposition and tying with 20 SWG binding wire, complete. Quantity shall bemeasured as per reinforcement drawing and with theoretical weights includingall authorized laps. Unauthorized chairs, spacers and laps will not be measuredand paid for.

373 600X450X700MM INS. CHAMBERS EA 4800INSPECTION CHAMBER Providing and constructing following size inspectionchambers with 230mm thick brick masonary in 1:5 cement mortar, excavation,75mm thick PCC 1:4:8 bed, plastering with neat cement finish, providing 16 mmthick MS plate cover with 50 x 50 x 6 angle frame etc. complete. Size600X450X700 mm

374 600X600X700MM INS. CHAMBERS EA 5000Same as above but size 600X600X700

375 450X450X700MM INS CHAMBERS EA 4650Same as above but size 450X450X700

376 SURFACE DRAIN MT 1900SURFACE DRAIN Providing and constructing surface drain 12" wide and 24"depth (average) with 9" BBM in CM1:4 with plastering on both sides includingexcavation, soling, PCC1:3:6, including giving necessary slope, etc., completed.

377 DRESSING OF DRIVEWAY SM 30DRESSING OF DRIVEWAY Dressing of existing driveway wherever requiredincluding excavation to required depth and providing/laying metalling upto 3" oras per required thickness compacted to level desired by ramming, filling up theinterstices with stone chips, stone grit powder as sub-base to fix the paverblocks later including all materials and labour, wherever necessary as perinstruction of HPCL Engineer/Architect.

378 BITUMINOUS MACADAM 75mm SM 450BITUMINOUS MACADAM 75mm THICK USING 60/70 GRADE BITUMEN:Providing and laying premix bituminous macadam base course with good qualitystone aggregate mix as follow 20mm = 30%, 12mm=35%,6mm=15% coarsesand 15 % and bitumen 60/70 grade 6% by weight .The aggregate shall be ofquality size and grading as specified and bitumen shall be straight run bitumenof grade 60/70 @ 6 % by weight of total mix . The job includes hot mixing byusing mini hot mix plant , transporting mix material and laying the same to therequired level & grade, rolling with power roller of 8 to 10 Ton capacity to achieve required compaction and density all material , labour etc. complete. The macadam course shall be laid in two layers of around equal thi ckness,each layer shall be rolled and compacted. Tack coat shall be applied betweenthe two layers@ 9.8 kg per 10 sqm.

379 TRANSP. OF 70 KL WITHIN 30 KM EA 14500Transportation of 70KL horizontal tanks to site including loading, unloadingetc. Complete upto 30KM from the source

380 TRANS. 70 KL TANK KM 45Same as above but beyond 30 km

381 TRANSP. OF 45 KL WITHIN 30 KM EA 9500Transportation of 45KL horizontal tanks to site including loading, unloadingetc. Complete upto 30KM from the source

Page 211

382 TRANS. 45 KL TANK KM 35Same as above but beyond 30 km

383 TRANSP. OF 22 KL WITHIN 30 KM EA 3060Transportation of 22KL horizontal tanks to site including loading, unloadingetc. Complete upto 30KM from the source

384 TRANS. 22 KL TANK KM 29Same as above but beyond 30 km

385 TRANSP. OF 16 KL WITHIN 30 KM EA 2959Transportation of 16KL horizontal tanks to site including loading, unloadingetc. Complete upto 30KM from the source

386 TRANS. 16KL TANK KM 29Same as above but beyond 30 km

387 TRANSP. OF 9 KL WITHIN 30 KM EA 2450Transportation of 9KL horizontal tanks to site including loading, unloading etc.Complete upto 30KM from the source

388 TRANS. 9KL TANK KM 27Same as above but beyond 30 km

389 TR.MONODU<30KM IN LOT UPTO 5NO LOT 1400The quantity will be calculated per trip upto maximum of carrying 5 pumps pertrip

390 TR.MONODU BEY30KM UPTO 5NO LOT KM 25The KM will be calculated per trip upto maximum of carrying 5 pumps per trip

391 TR.DUAL/2T DU<30KM-LOT UPTO 5 NO LOT 1550The quantity will be calculated per trip upto maximum of carrying 5 pumps pertrip

392 TR.DUAL/2T DU BEY30KM-TO 5NO LOT KM 25The quantity will be calculated per trip upto maximum of carrying 5 pumps pertrip

393 TR. MPD<30 KM IN LOT UPTO 5 NO LOT 1650The quantity will be calculated per trip upto maximum of carrying 5 pumps pertrip

394 TR.MPD BEY30 KM IN LOT UPTO 5 NO KM 37The quantity will be calculated per trip upto maximum of carrying 5 pumps pertrip

395 45 KL TANK INSTALLATION EA 22000Installaion of HPCL supplied Tanks of 45KL capacity in earth pit /underdriveway including lowering, providing holding down arrangement, Hydrostatictesting to pressure of 5psi, supplying & filling with water with necessary 50 mmdia pipe & on successful completion emptying out the water from tank , cleaning& drying the inner surfaces with cloth/ cotton waste etc., doping with three coatsof shalimastic HD over a coat of GETSET (Type-A) primer with minimumthickness of 1.5mm. 24Hrs drying time between each coat has to bemaintained.

396 22KL TANK INSTLN. EA 14000Same as above but size 22 KL

397 16KL TANK INSTLN. EA 11500Same as above but size 16 KL

398 9KL TANK INSTLN. EA 10500Same as above but size 9 KL

399 SS RAILING FOR PUMP ISLANDS EA 8000

Page 212

Fabricating and fixing S. S. Railing with 40 mm SS square tube & 25 mm dia SSpipe ( SS of 202 grade) as per the drawing. The item includes fabrication,buffing of the railing upto req. finish, fixing the railing at position with m20 gradeconcrete, finising the driveway properly etc. complete

400 CHRO.PLATD MS PUMPISLAND GUARD EA 7500Fabricating and fixing cromium plated MS Railing with 50 mm DIA and 40 mmdia B CLASS MS pipes of Swastik/Jindal/Zenith make as per the StandardHPCL drawing. The item includes fabrication, buffing of the railing upto req.finish, fixing the railing at position with m20 grade concrete, finising the drivewayproperly etc. complete

401 PUMP ISLAND MT 1400Construction of pump island 1m wide with 230mm thick brick masonry in CM1:5, 12mm thick plastering in Cm 1:4 roughened to receive granite tiles includingexcavation, 75mm thick PCC 1:4:8 , sand filling and constructing the wall400mm above the finished driveway level and 600mm below the finisheddriveway level .

402 INSTLN. OF MONO PUMPS EA 565Installation of MONO pumps on pedestal including providing & fixing foundationbolt of 12mm dia & connecting suctionpipe, electrical, earthing connections tothe pump.

403 INSTLN. OF DUAL/2T MIX PUMPS EA 750Installation of DUAL pumps on pedestal including providing & fixing foundationbolt of 12mm dia & connecting suctionpipe, electrical, earthing connections tothe pump.

404 INSTLN. OF MPD PUMPS EA 1000Installation of MPD pumps on pedestal including providing & fixing foundationbolt of 12mm dia & connecting suctionpipe, electrical, earthing connections tothe pump. Supplying & Laying 'C' Class MS ERW black steel screwed pipeline (TATA/SWASTIK/JINDAL make)Conforming to IS 1239 (part I) – latest edition tothe required slope & alignment with heavy duty MS fittings like elbows, teesincluding doping pipe line with 1.5mm thick layer of shalimastic HD in 2 coatsetc, complete. The joints are to be made leak proof by using jointing materialslike Litharge, Glycerin, Shellac, holdite . The pipeline to be tested with 5PSI asper standard specification.

405 40MM DIA PIPELINE MT 495Supplying & Laying 'C' Class MS ERW black steel screwed pipeline(TATA/SWASTIK/JINDAL make) Conforming to IS 1239 (part I) – latest editionto the required slope & alignment with heavy duty MS fittings like elbows, teesincluding doping pipe line with 1.5mm thick layer of shalimastic HD in 2 coatsetc, complete. The joints are to be made leak proof by using jointing materialslike Litharge, Glycerin, Shellac, holdite . The pipeline to be tested with 5PSI asper standard specification. Size 40 mm Diameter.

406 50MM DIA PIPEINE MT 571Same as above but size 50 mm Diameter

407 80MM DIA PIPELINE MT 765Same as above but size 80 mm Diameter

408 40MM DIA CHECK VALVE EA 1890Supply and fixing ISI marked angular check valve of Leader/GG make size40mm diameter

409 50MM DIA CHECK VALVE EA 2700

Page 213

Same as above but size 50 mm Diameter410 S/F/L MS C CL.WELDED PL2.5"DIA MT 875

Supplying & Laying 2.5" Dia Heavy-duty 'C' Class MS Steel ERW Welded P/L (TATA/SWASTIK/JINDAL make) Conforming to IS 1239 (part I) – latest editionto the required slope & alignment with heavy duty MS fittings like elbows,sockets,unions , tees etc. including doping pipe line with 3 coats of 'ShalimasticHD THIXOTROPIC of STP cold applied anti corrosive treatment after preparingthe surface as per manufacturer specifications. The joints are to be made leakproof. The P/L which would laid aboveground shall be painted with two coats ofsynthetic enamel over two coats of Zinc Chromate primer of approved qualityand shade. The pipeline shall be tested at a pressure of 5Kg / sqcm.

411 S/F/L MS C CL.WELDED PL2.0"DIA MT 765Same as above item but with Pipe dia as 2.00"

412 FLANGE JOINT 2.5" DIA EA 850Supplying & fixing of 2.5 inches dia C Class MS Flanges for Petroleum productsof approved make and of Heavy duty usage.

413 FLANGE JOINT 2" DIA EA 775Supplying & fixing of 2 inches dia C Class MS Flanges for Petroleum products ofapproved make and of Heavy duty usage.

414 P/F BALL VALVES 2.5" DIA EA 5700Supply and fixing ISI marked Ball valve of Leader/ Sant/ Syall make. 2.5inches Dia

415 P/F BALL VALVES 2.0" DIA EA 5300Supply and fixing ISI marked Ball valve of Leader/ Sant/ Syall make. 2.0inches Dia

416 INSTALLATION OF STP EA 1900Installation of STP pumps on Tank Manhole including connection with suctionpipe, electrical, earthing etc. complete.

417 4 WAY MANIFOLD EA 5800S/fixing of 4-way MS manifold on Tank manhole for providing connection todifferent dispensers.

418 MS FILL CAP EA 407Supply and fixing MS fill cap of 80mm dia with locking arrangement includingGodrej 6 lever brass lock

419 MS DIP CAP EA 275Supply and fixing MS dip cap of 50mm dia with locking arrangement includingGodrej 6 lever brass lock

420 GRANITE SLAB SM 2908Providing and fixing 18-20 mm thick pre polished water cut black granite slabfor pump island top including providing 25mm thk bed cement mortar 1:5 (1cement : 5 coarse sand) , floating cement slurry and finishing the joints withwhite cement mixed with matching colour pigment.

421 GRANITE TILES SM 1550Providing and fixing 10 mm thick pre polished water cut black granite tiles forpump island dado including providing 12mm thk bed cement mortar 1:4 (1cement : 4 coarse sand) , fixing the tiles with neat cement paste and finishingthe joints with white cement mixed with matching colour pigment.

422 SILICA GEL TRAP EA 2000Providing and fixing flanged end silica get trap for vent as per standard HPCLdesign including filling of silica get crystals, cutting and reconnecting vent pipes,etc, complete.

Page 214

423 TEE VENT HOOD EA 435Providing and fixing MS Tee Vent Hood with brass wire guage of 25mesh/sq.inch as per standard specification.

424 EXUMING- 9 KL TANK EA 5314Exhuming under ground tanks with all fittings from earth pit includingdisconnecting suction, fill, vert pipe , opening man hole cover, excavation,dewatering if encountered, degassing of tank, stacking the tank as directed byEIC etc.Complete. Back filling with sand will be paid separately. Size 9KL tank.

425 EXUMING- 14/16KL TANK EA 6376Same as above but for 14/16KL tank

426 EXUMING- 22 KL TANK EA 7439Same as above but for 22KL tank

427 EXUMING- 45 KL TANK EA 10627Same as above but for 45KL tank

428 EXUMING- 70KL TANK EA 14492Same as above but for 70KL tank

429 DISMANTLING OF P/ISLAND MT 319Dismantling of existing pump island 1m wide and carting away debris includingremoval of pump and disconnecting pipeline etc. complete.

430 DISMANTLING RCC ROOF M3 556Dismantling of RCC roof, beam, column including carting away debris

431 REMOVAL OF AC SHEET SM 74Removal of AC sheet from roof and stacking as directed by EIC

432 REMOVAL OF ST. STEEL TM 3575Removal of structural steel and stacking as directed by EIC

433 EXCAVATION IN RCC M3 603Excavation in RCC of any thickness by using pneumatic tools like Jackhammers, chisels or manually using hammers , chisels etc cutting thereinforcement steel and stacking the same .The job also includes disposing thedismantled RCC within/outside HPCL premises to any unobjectionable place allcomplete as directed by Engg.-In-Charge.

434 DIS. OF BRICK MASONARY M3 338Dismantling of brick masonary/PCC /RR masonary including carting away debris

435 REMOVAL OF FALSE CEILING SM 34Dismantling of all types of ceilings except of bk work/CC, sheets like AC, TRAC,GYPSUM BOARD etc. Scope of job includes handing over of all 'J', 'L' hooks,nuts and bolts, suspendors or other joineries in proper bags. Party to ensurejoint measurement of the job to be dismantled, alongwith EIC, before start.Payment shall be made basis the joint measurement, in absence of any jointmeasurement record HPCL EIC decision shall be final.

436 REMOVAL OF MS/AL DOORS SM 76Removal of MS/ Aluminium doors/ windows/fixed glazing and stacking asdirected by EIC.

437 SHIFTING OF MSEB MAINS EA 6956Shifting of MSEB Main, laisoning with MSEB officials, including payment of allincidental charges etc., all complete ( Payment made to MSEB shall bereimbursed to contractor by HPCL on submission of original receipt).

438 REMOVING OF ID SIGN/MASTERPOLE EA 2705

Page 215

Removing of existing ID sign carefully without damage and shifting the same orrefixing the same at new place within the primises as per HPCL instructions.Job includes making necessary electrical connecitons, etc., complete.

439 TRANSPORATATION OF Q&Q TOWER FROM REGIONAL OFFICE/DEPO TTO THE RETAIL OUTLET EA 483

440 REMOVAL OF YARD LIGHT POLE EA 2029Removing the existing yard light poles including removing of light fixturescarefully and refixing the same at designated place within the premises. Jobincludes excavation, foundation in PCC 1:2:4 with foundation bolts, etc.,complete in all respect.

441 TRIMMING OF TREES LS 2898Trimming the branches of trees above a minimum height of 4m from groundlevel and carting away the same from the site when and whenever required asper instruction of HPCL

442 REMOVAL OF FENCING MR 37Removing existing chainlink/barbed wire fencing including removing the groutedangles, rods etc., and stacking the same carefully as directed.

443 BREAKING OF RCC SLAB SM 164Breaking of RCC slab over tank and driveway by manual means or by usingpneumatic breaker and carting away the debris to unobjectionable place outsideRO premises.

444 REMOVING OF PAVER BLOCK SM 135Removal of existing paver blocks carefully and without damage and refixing thesame after the job completion in proper line and level and compaction etc,complete.Removing exiting dispensing pumps after disconnecting pipeline, electricalconnection etc, and stacking carefully as directed.

445 REMOVING OF SINGLE PUMPS EA 280Removing exiting dispensing pumps after disconnecting pipeline, electricalconnection etc, and stacking carefully as directed.

446 REMOVING OF DUAL/2T MIX PUMPS EA 386Removing exiting dispensing pumps after disconnecting pipeline, electricalconnection etc, and stacking carefully as directed.

447 REMOVING OF MPD PUMPS EA 870448 RELAYING OF 40 MM DIA P/L MT 188

Relaying of MS threaded pipeline to the required slope of alignment andhydrotesting with the pressure of 5 psi with providing and fixing necessary MSheavy duty fittings like elbows, tees, including providing and applying doping thepipeline with shalimastic HD 2 coats. Size 40mm dia

449 RELAYING OF 50 MM DIA P/L MT 232Same as above but size 50 mm Diameter

450 RELAYING OF 80 MM DIA P/L MT 348Same as above but size 80 mm Diameter

451 FILL PIPE BRASS COUPLING EA 1256Supplying & fixing 75 mm dia Brass coupling for fill point

452 RUBBER HOSES FOR DECANTING EA 4637

Page 216

Tankar unloading Hoses : Supply of eletrically bonded petroleum productunloading hose with uniform bore of 61mm and 3.3 mtr in length havingneoperne rubber of premium quality in outer cover and acrylic nitrile rubber ininner lining with high degree of flexibility, reinforced with fully embeded helicalwire and static copper wire for eletrically continuty, rubbrer hose should haveoutside corrugated without external armouring suitable for handling petroleumproducts up to working pressure of 3.5 kg/sqmm and confirming to IS10733/1983 type 1B with plain ends and 2 nos heavy gun meatal hose nippleswith nitrile rubber rings fitted inside and assembled by 2 GI hose clips to eachside of above mentioned hose, supplier to provoide test certificate of eletricalcontinuty for each and 6 months Gaurantee againest any manufacturing defects.

453 INSTN. CLUB HP SIGN (PART-H) EA 2367Installing Club HP Signage Board with necessary CC 1:2:4 foundation uptorequired depth. Job also supply 4 nos of 12mm dia x 750mm long MSfoundation bolts etc, complete.

454 INSTALLATION - SIGNATURE PYLON EA 17390Installing SIGNATURE PYLON Board on the already constructed/existing RCCfoundation with the help of Crane and all the required tools and machinery inproper line and level etc complete.

455 DISMANTLING - SIGNATURE PYLON EA 7246Removal of SIGNATURE PYLON Board from the existing RCC foundation withthe help of Crane and all the required tools and machinery and keeping in safecustody of dealer at the retail outlet or as directed by EIC.

456 INSTAL.-MASTERPOLE/CITY PYLON EA 6280Installing CITY PYLON/ REGULAR HP MASTERPOLE Board on the alreadyconstructed/existing RCC foundation with the help of Crane and all the requiredtools and machinery in proper line and level etc complete.

457 INSTLN. OF AIR TOWER EA 2319Installing Air Tower facility with necessary CC 1:2:4 foundation of required sizeand also with necessary electrical connection.

458 POSITIONING OF Q&Q TOWER EA 850Positioning of Q & Q Tower Board to shown place with necessary foundation.

459 FIXING OF WATER COOLER EA 1159Fixing of water cooler with necessary electrical connections of 5/15 Amp switchboard with necessary wiring.

460 P/P OF QUICK CARE POINT EA 1159Providing and painting work for Quick Care Point as per standard design.

461 INST.-INGRESS& EGRESS SIGNAGE EA 531Installing Ingress and Egress Signage Board with necessary CC 1:2:4foundation and with necessary electrical connection.

462 INSTAL OF CREDIT CARD COUNTER EA 966Installing Credit Card Counter with providing and making electrical connectionsof 5 Amp Switch socket and telephone socket connection with necessary wiring.

463 INST.-15 /25/35 KVA GENERATOR EA 4831Installation of 15/20/25/30/35 KVA Capacity DG set on AVM pads includingshifting from storage yard to DG room, all cable connection, installation of fueltank, silenser pipe ,battery connection, etc. complete.

464 REMOVAL OF WATER FROM U/G TANK EA 3513

Page 217

Removal of Rain water/ sludge etc from Underground tank with the help ofmanually operated foot pump/hand pump etc and cleaning the tank from inside.Job includes handling water/product mixture safely and following all the safetyrules during the job.

465 CONILCAL PARKING STAND EA 1353Supply of Plastic Conical Parking stand /Guard of standard height and size or asapproved by the Engineer-In -Charge.

466 PIPELINE TESTING / REPAIR EA 2743Testing of pipeline for any leakage with the help of Hydro pressure testingPressure Gauge , identifying the location of the leakage and repairing the lineeither by replacing the leacky pipeline or by cutting and reusing the existing lineand testing the joint properly at the required test pressure.Rate to include all thetools/machinery and pipeline material, unions,bends, elbows etc except checkvalve.

467 FIRE EXTINGUISHER -10 KG DCP type EA 7608Supply of 10 KG capacity DCP type fire extingisher of approvedmake(MINMAX/ZENITH/LITEX) and having ISI mark stamped on cylinder body.

468 FIRE EXTINGUISHER -7.5 KG DCP type EA 5024Supply of 7.5 KG capacity DCP type fire extingisher of approvedmake(MINMAX/ZENITH/LITEX) and having ISI mark stamped on cylinder body.

469 FIRE EXTINGUISHER -4.5 KG CO2 type EA 11159Supply of 4.5 KG capacity CO2 type fire extingisher of approvedmake(MINMAX/ZENITH/LITEX) and having ISI mark stamped on cylinder body.

470 FIRE EXT- 75 KG DCP(TROLLEY) TYPE EA 41543Supply of 75 KG capacity DCP type TROLLEY FITTED fire extingisher ofapproved make(MINMAX/ZENITH/LITEX) and having ISI mark stamped oncylinder body.

471 FIRE EXT -15 KG CO2(TROLLEY) TYPE EA 35747Supply of 15 KG capacity CO2 type TROLLEY FITTED fire extingisher ofapproved make(MINMAX/ZENITH/LITEX) and having ISI mark stamped oncylinder body.

472 CHANGE OVER SWITCH EA 3381S/Fixing of 63 A change over switch of L&T / HAVELL'S make

473 CABLE TRAY-300 MM WIDE MR 862Supply, erection/installation/mounting of 16 SWG 300mm wide perforated GIcable tray inclusive of cable binding with suitable GI clamps, GI hooks, GI nutsand bolts complete in the tray in a neat way. The width specified shall be ofcable mounting area. Bends at both the sides of cable tray shall be in addition toit.

474 CABLE TRAY-150 MM WIDE MR 609Supply, erection/installation/mounting of 16 SWG 150mm wide perforated GIcable tray inclusive of cable binding with suitable GI clamps, GI hooks, GI nutsand bolts complete in the tray in a neat way. The width specified shall be ofcable mounting area. Bends at both the sides of cable tray shall be in addition toit.

475 EARTH PIT MS BOX FOR BUS BAR EA 2802Supply and fixing of MS box for earthing pit busbar for keeping heavy dutycrocodile clip and multistranded copper wire used during decantation.

476 ELEC.SUBMETER-SINGLE PHASE EA 4251

Page 218

S/Fixing of MAXWELL / L&T /PIMCO make CT operated , MSEB certified,Single Phase electrical sub-meter including necessary electrical connections etccomplete.

477 ELEC.SUBMETER- THREE PHASE EA 5700S/Fixing of MAXWELL / L&T /PIMCO make CT operated , MSEB certified,Three Phase electrical sub-meter including necessary electrical connections etccomplete.

478 DIP ROD- 3.0 MTR- ALUMINUM EA 1256

Supply of 3.0 Mtr long Aluminum Dip rod for taking product dip measurements atretail outlet.

479 DIP ROD- 3.0 MTR- Brass EA 3092Supply of 3.0 Mtr long Brass Dip rod for taking product dip measurements atretail outlet.

480 WATER FLOW SUB-METER- 25 MM DIA EA 2657Supply and installation of PCMC/PMC approved/Calibrated water flow meter of25 mm dia

481 WATER FLOW SUB-METER- 12 MM DIA EA 1449Supply and installation of PCMC/PMC approved/Calibrated water flow meter of12 mm dia

482 CLEANING OF VENT PIPE/VENT HOOD EA 2415

Cleaning of vent pipe and removal of blockage in the form of dust/product. Rateto include venting out the trapped product /material with the help of compressedair etc complete. Rate to also include necessary excavation,removal/dismantling of vent pipes and refixing the same after cleaning of vents.

483 REPAIRING OF EXISTING BM CHAMBER EA 1932Repairing of existing brick masonry chamber inclduing breaking of CC,necessary modification to the chamber and replstering the inside surface ,Making the chamber good to the satisfaction of EIC.

484 TARFELT WATERPROOFING SM 362Supplying and laying of Tarfelt waterproofing by using ISI mark Tarfelt withasphalt primer and using 30/40 asphalt over the Asbestos Sheet Roofing, etc.,complete (5 Course Treatment as specified by Manufacturer)

485 GASKET ON TANK MANHOLE EA 850The manhole cover to be fitted with providing and fixing 3mm thick RAF Gasketpacking (Champion make, Champion-59) of 750mm dia.

486 HEAVYDUTY BRASS CROCODILE CLIP EA 121Supply and fixing of Heavy Duty HPCL approved Brass Crocodile clips at theend of each cable termination for connecting to the tank lorry during unloading .

487 TANK MANHOLE MODIFICATION EA 6763Modification to the existing underground tank manhole , with the provision of 1no 75 mm dia and 1 no 100 mm dia riser pipe for the AUTOMATION purpose.Rate to include removing the existing manhole from the tank after empting outthe tank & complete degassing , covering the existing tank opening withstandby/stepney type manhole and fabricating/cutting/welding the existingmanhole to have above mentioned provisions. Rate to also inlude refixing of themodified manhole onto the tank with new gasket of approved grade andthickness ( as approved by HPCL) and supply/fixing of the 75 mm dia MS -CClass pipe ( 10" in length ) and 100 mm dia MS -C Class pipe ( 8" in length ) onthe modified manhole .

488 100 MM DIA GI PIPE MT 725

Page 219

Supplying & Laying 'B' Class Galvanised Iron pipeline of 100 mm dia. (makes-TATA/Swastik/JINDAL/Zenith) Conforming to IS 1239 (part I) – latest edition tothe required slope & alignment with heavy duty MS fittings like elbows, teesincluding doping pipe line with 1.5mm thick layer of shalimastic HD in 2 coatsetc, also including cutting, bending & supply and laying of 17 SWG annealedbinding wire inside the HUME Pipe for pulling cables in future etc complete. Thejoints are to be made leak proof by using jointing materials like Litharge,Glycerin, Shellac, holdite . The pipeline to be tested with 5PSI as per standardspecification.

489 200 MM DIA GI PIPE MT 1304Same as above but size 200mm diameter

490 ROOFING WITH TRACDEK Hi Rib 100 SM 589Providing and installing roofing with tracdek Hi Rib 100 or approved equivalentbare Galvalume high tensile cold rolled steel as per AS 1397 coating class AZ150 (minimum 150 gm / sqm Zinc - Aluminium alloy coating mass total of bothsides ) Yield strength 275 Mpa thickness of bare metal : 0.42 mm ,total coatedthickness : 0.47 mm Approximate mass of completed roofing shall be 4.12 kg/sqm. Rate shall be including providing ridge piece, horizontal /vertical flashingnear illuminated banding.

491 ROOFING WITH TRACDEK CLIPPON SM 744Providing and installing roofing with tracdek Klippon or approved equivalent bareGalvalume high tensile cold rolled steel as per AS 1397 coating class AZ 150(minimum 150 gm / sqm Zinc - Aluminium alloy coating mass total of both sides) Yield strength 275 Mpa thickness of bare metal : 0.50 mm ,total coatedthickness : 0.55 mm etc. Rate shall including providing ridge piece,horizontal/vertical flashing near the illuminated banding.

492 18SWG CRCA SHEET WITH POW COAT SM 961Supplying and fixing 18 SWG CRCA sheet with powder coating one side andcoat red oxide primer & two coats enamel paint side for facia to Canopy on therear sides , ( The sides which are visible to the road shall be providing withilluminated bands which is covered by a coat of red oxide primer and two coatsof 1st quality synthetic enamel paint one side and poder coating with HP blueshade on other side. Necessary securely shall be paid separately.

493 18 SWG THICK G I SHEET GUTTER SM 932Providing and fixing 18 SWG thick G.I. sheet Gutters wth 350 gms/sqm of Zinccoating conforming to clause 7.0 of IS : 277 of any shape in slope with 40 mm x3mm M.s. Brackets at 1000 mm maximum spacing and 8 mm dia G.I. J or Lhooks , boltsand nuts, G,i. Limpet and bitumen washers , sealing the joints withsilicon sealant etc. complete.

494 CANOPY LIGHT 150 WATT EA 5314Supply of 1 x 150 W metal hallide canopy light fixtures with lump WIPRO cat no.WHH 94250 or equivalent

495 CANOPY LIGHT CFL 85 WATT EA 2414Supply of 1 x 85 W Energy saving CFL canopy light fixtures with lampWIPRO/Crompton/Bajaj or equivalent

496 DRILLING 6" DIA BOREWELL MR 135Drilling 5" dia borewell up to requied depth in all kinds of soil including rock usingair compressor rig .Rate to include washing with compressor after installation ofcasing pipe, providing bentonite soil if required etc. completed.

497 6"DIA HDPE CASING PIPE6KG/SQCM MR 242

Page 220

Supply and fixing 5" dia HDPE cashing pipe 6 KG/SQCM presure rating 498 6"DIA HDPE SLOTTED 6 KG/SQCM MR 275

Supply and fixing 5" dia HDPE slotted pipe 6 KG/SQCM presure rating 499 SINGLE PHASE SUBMER PUMP 1.0HP EA 17659

Supply and installtion of single phase 1.0 HP submerible pump of kirloskar catno. KU4- 0709S discharge range 1.2-8 cum/hr head range 59 -10m along withdry run preventor and starter 500 SINGLE PHASE SUBMER PUMP 1.5HP EA 21000Same as above but size 1.5 HP

501 32MM NB HDPE PIPE WIPE GI NIPPLE EA 58Supply and installation of 32mm NB HDPE pipe wipe GI nipple at both end

502 3C X 2.5 SQMM COPPER FLAT CABLE MR 121Supply and laying 3C X 2.5 sqmm copper flat cable

503 GEOLOGICAL TESTING FOR BOREWELL EA 2415Carrying out Geological testing for finalisation of location of borewell

504 SINGLEPHASE 1HPJETPUMP WITH ST. EA 7729Supply and installation of single phase 1 HP jet pump with starter

505 32MM NB HDPE PIPE&25MM NB HDPE MR 116Supply and installation of 32mm NB HDPE pipe and 25mm NB HDPE pipe withrequied accessories for jet pump.

506 WATER HARVESTING TYPE I EA 6570Providing rain water harvesting type I as per attached drawing internal size 1.5mx 1.5m x 3m depth from GL.

507 WATER HARVESTING TYPE II EA 7246Providing rain water harvesting type II as per attached drawing internal size 1.5m x 1.5m x 2m depth from GL. And bore well inside.

508 DUG CUM BORE/WATERHARV.TYPEIII EA 10627Providing dug cum borewell type rain water harvesting type III as per attacheddrawing with 1.2m dia 65mm thick pre cast RCC rings, 150mm thick RCC slabon top, providing borewell of 10m depth inside the well etc . Complete.

509 TESTING OF WATER EA 1930Collection of water sample from the borewell and getting it tested from approvedlaboratory for the potability. The report to be submitted to the HPCL site-in-charge

510 LETTERING/ PAINTING FOR"FLUERS" EA 43400

Page 221

SPECIFICATION FOR LETTERING WORK FOR TOILET BLOCK- "Fleurs" BOX LETTER MADE OUT OF 2 MM THK S S MATERIAL WITH SIDE 25 MMTHK BOX TYPE LETTER WITH BACKSIDE SCREW BRAZING FOR FITTINGARRANGEMENT. INCLUSIVE P.U. COATING ( BLACK) LETTER "F" 60" HEIGHT.BOX LETTER MADE OUT OF 2 MM THK S S

MATERIAL WITH SIDE 25 MM THK BOX TYPE LETTER WITH BACKSIDESCREW BRAZING FOR FITTING ARRANGEMENT. INCLUSIVE P.U.COATING ( BLACK)

LETTER "L" 36" HEIGHT.BOX LETTER MADE OUT OF 2 MM THK S SMATERIAL WITH SIDE 25 MM THK BOX TYPE LETTER WITH BACKSIDESCREW BRAZING FOR FITTING ARRANGEMENT. INCLUSIVE P.U.COATING ( BLACK)

LETTER "EURS" 48" HEIGHT.CLEAN TOILETS SIZE 4" HEIGHT X 1" THK 12NOS. FLOWER DESIGN WHITE/YELLOW P.U. COAT .APPLYING 2 COAT TEXTURED PAINT OF APPROVED MAKE AND SHADEON TOILET BLOCK FASCIA WALL (APPROX QTY- 12 SQM ) INCLUSIVE OFALL MATERIAL AND LABOR, TOOLS ETC COMPLETE.

Page 222