cl & psl50 seriesdownload2.creminternational.com/spengler/10037114_03_spengler_tt_sm.pdf · 4...

SpenglerTT_SM_ENPart No.: 10037114_03

CL & PSL50 SERIESSERVICE MANUAL

2

CL & PSL50 SeriesCONTENTS

CONTENTS

MANUAL REVISIONS

SERVICE OVERVIEW4 Semi-annual service tasks4 Semi-annual service required equipment5 Annual service tasks5 Annual service required equipment6 Biannual service tasks6 Biannual service required equipment

MAINTENANCE SCHEDULE

SERVICE MENU9 Accessing the service menu

SERVICE TASKS10 Step 1: Clean canisters, canister outlets11 Step 2: Clean spout adaptor, mixers, Black Coffee Kit12 Step 3: Clean air channel, air filters13 Step 4: Clean espresso brewer14 Step 4: Install espresso brewer service kit (annually & biannually)15 Step 4: Reassemble espresso brewer16 Step 5: Clean monobrewer17 Step 5: Install monobrewer service kit (annually & biannually)18 Step 5: Reassemble monobrewer19 Step 6: Clean bean hopper20 Step 7: Clean grinder, replace outlet21 Step 8: Replace grinder soft ring (annually & biannually), adjustment ring (biannually only)

22 Step 9: Replace extractor fan (biannually only)23 Step 10: Replace fast mixer motor assembly (annually & biannually)24 Step 11: Replace overpressure valve (annually & biannually)25 Step 12: Replace non-return valve (annually & biannually)26 Step 13: Inspect inlet valve27 Step 14: Clean interior28 Step 15: Reinstall bean hopper29 Step 16: Reinstall air channel and filters30 Step 17: Reinstall spout adaptor, mixers, Black Coffee Kit31 Step 18: Reinstall canisters32 Step 19: Reinstall espresso brewer33 Step 20: Reinstall monobrewer

TROUBLESHOOTING34 Error codes, causes, solutions

SCHEMATICS36 Hydraulic diagram PSL50 ES12B37 Hydraulic diagram PSL50 ES1338 Hydraulic diagram PSL50 FBT1439 Hydraulic diagram CL2240 Electrical diagram PSL50 series43 Electrical diagram CL series

3

CL & PSL50 Series

Rev. # Date TSB # Description

01 Jan. 19, 2018 None First draft released for technical review.

02 Feb. 09, 2018 None Updated based on technical review feedback.

03 March 16, 2018 None Finalize service kit contents.

04

05

06

07

08

09

10

MANUAL REVISIONS

4

CL & PSL50 SeriesSERVICE OVERVIEW

Semi-annual service tasks

The service tasks listed below are to be done on an annual basis to guarantee good dispenser functionality and maintain warranty compliance. Step-by-step instructions are provided on the following pages.

• Clean canisters, canister outlets• Clean spout adaptor, mixers, Black Coffee Kit• Clean air channel, replace air filters• Clean espresso brewer• Reassemble espresso brewer• Clean monobrewer• Reassemble monobrewer• Clean bean hopper• Clean grinder, replace outlet• Clean dispenser interior• Reinstall bean hopper• Reinstall air channel and filters• Reinstall spout adaptor, mixers, Black Coffee Kit• Reinstall canisters• Reinstall espresso brewer• Reinstall monobrewer

Semi-annual service required equipment

The following cleaning equipment/consumable items are required to perform the semi-annual service tasks.

• Door key• Cleaning cloth/sponge• Mild kitchen cleaning spray• Service access code (available from the service technician or distributor)• Air filter material (PN10034178)• Grinder outlet* (one per grinder - PN10031032)

Items marked with a “*” are only required if the dispenser is equipped with the applicable system.

Important: The Semi-annual Service (6 month service tasks) shall only be performed by a trained technician using all required safety equipment as outlined during the training session(s) and service kits from the original equipment manufacturer.

5


Annual service tasks Annual service required equipment


• Clean canisters, canister outlets• Clean spout adaptor, replace mixers, Black Coffee Kit• Clean air channel, replace air filters• Clean espresso brewer• Install espresso brewer service kit• Reassemble espresso brewer• Drain boiler• Clean monobrewer• Install monobrewer service kit• Reassemble monobrewer• Clean bean hopper• Clean grinder, replace outlet• Replace grinder soft ring• Replace fast mixer motor assembly• Replace overpressure valve• Clean dispenser interior• Reinstall bean hopper• Reinstall air channel and filters• Reinstall spout adaptor, mixers, Black Coffee Kit• Reinstall canisters• Reinstall espresso brewer• Reinstall monobrewer

Important: The Annual Service (12 month service tasks) shall only be performed by a trained technician using all required safety equipment as outlined during the training session(s) and service kits from the original equipment manufacturer.

The following cleaning equipment/consumable items are required to perform the annual service tasks.

• Door key• Cleaning cloth/sponge• Mild kitchen cleaning spray• Service access code (available from the service technician or distributor)• Air filter material (PN10034178)• Fast mixer unit* (PN10032974)• Mixer bracket assembly (PN 10011038)• Espresso Service Kit* (PN10021379)• Monobrewer Service Kit* (PN10037202 for coffee or PN10037220 for tea)• Overpressure Valve (PN10024356)• Non-return valve (PN100246950)• Grinder outlet* (one per grinder - PN10031032)• Grinder soft ring* (one per grinder - PN10032591)• Grinder adjustment ring* (one per grinder - PN10031008)


6


Biannual service tasks Biannual service required equipment


• Clean canisters, canister outlets• Clean spout adaptor, mixers, Black Coffee Kit• Clean air channel, replace air filters• Clean espresso brewer• Install espresso brewer service kit• Reassemble espresso brewer• Drain boiler• Clean monobrewer• Install monobrewer service kit• Reassemble monobrewer• Clean bean hopper• Clean grinder, replace outlet• Replace grinder soft ring, adjustment ring• Replace extractor fan• Replace fast mixer motor assembly• Replace overpressure valve• Replace inlet valve• Clean dispenser interior• Reinstall bean hopper• Reinstall air channel and filters• Reinstall spout adaptor, mixers, Black Coffee Kit• Reinstall canisters• Reinstall espresso brewer• Reinstall monobrewer

Important: The Biannual Service (24 month service tasks) shall only be performed by a trained technician using all required safety equipment as outlined during the training session(s) and service kits from the original equipment manufacturer.

The following cleaning equipment/consumable items are required to perform the biannual service tasks.

• Door key• Cleaning cloth/sponge• Mild kitchen cleaning spray• Service access code (available from the service technician or distributor)• Air filter material (PN10034178)• Fast mixer unit* (PN10032974)• Mixer bracket assembly (PN10011038)• Spout adaptor (PN100166133 and PN10009288)• Espresso Service Kit* (PN10021379)• Monobrewer Service Kit* (PN10037202 for coffee or PN10037220 for tea)• Overpressure Valve (PN10024356)• Non-return valve (PN100246950)• Grinder outlet* (one per grinder - PN10031032)• Grinder soft ring* (one per grinder - PN10032591)• Grinder adjustment ring* (one per grinder - PN10031008)• Extractor fan (PN10013350)• Ingredient canisters and outlet chutes (see below for part numbers)- CL22: PN1003379 (1pcs) + PN10033780 (1pcs) + PN1009619 (2pcs) ES12B: PN10009570 (1pcs) + PN10009705 (1pcs) + PN1009619 (2pcs) ES13: PN10009562 (1pcs) + PN10009563 (1pcs) + PN10009705 (1pcs) + PN1009619 (3pcs) FBT14: PN10009562 (1pcs) + PN10009563 (1pcs) + PN10009567 (1pcs) + PN10009704 (1pcs) + PN1009619 (4pcs)


7

CL & PSL50 Series

System ComponentsSemi-annual (every 6

months/12,500 servings*) Service Tasks

Annual (every 12 months/25,000 servings*)

Service Tasks

Bi-annual (every 24 months/50,000 servings*)

Service TasksReference Instruction

Hydraulic System

Overpressure valve Inspect for leaksReplace OVERPRESSURE VALVE

14BAR PN10024356Replace OVERPRESSURE VALVE

14BAR PN10024356See pg. 24

Non-return valve Inspect for leaksReplace NON-RETURN VALVE

PN10024695Replace NON-RETURN VALVE

PN10024695See pg. 25

Inlet valve Inspect for leaks See pg. 26

Water Filter In-tank water filter Check through-put, replace as needed based on manufacturer recommendations See filter manufacturer’s recommendations

Air ChannelAir Filters Remove & Clean Replace FILTER MAT PN10034178 Replace FILTER MAT PN10034178 See pg. 12, 29

Extractor Fan Remove & CleanReplace EXTRACTION FAN

PN10013350See pg. 22

Brewers

Espresso brewer Remove & CleanRebuild w/ ESPRESSOBREWER KIT

PN10037204Rebuild w/ ESPRESSOBREWER KIT

PN10037204See pg. 13-15, 32

Monobrewer (BTB/FBT) Remove & Clean

BTB (coffee) versions rebuild w/ MONOBREWER KIT COFFEE

PN10037202

FBT (tea) versions rebuild w/ MONOBREWER KIT TEA

PN10037220

BTB (coffee) versions rebuild w/ MONOBREWER KIT COFFEE

PN10037202

FBT (tea) versions rebuild w/ MONOBREWER KIT TEA

PN10037220

See pg. 16-18, 33

GrindersGrinder outlets

Replace w/ GRINDER OUTLET PN10031032

Replace GRINDER OUTLET PN10031032

Replace GRINDER OUTLET PN10031032

See pg. 21-22Grinder motors Clean with tablets Replace SOFTRING PN10032951

Rebuild w/ SOFTRING PN10032951 & ADJUSTMENT RING PN10031008

Mixers and Spouts

Spouts and adaptors Remove & CleanReplace NOZZLE HOLDER

PN100166133 & DISPENSE NOZZLE PN10009288

See pg. 11, 23, 30

Steam traps Remove & CleanReplace FAST MIXER UNIT PN

10032974Replace FAST MIXER UNIT PN

10032974Mixer bodies Remove & Clean

Mixers motors Remove & CleanReplace MIXER BRACKET ASSY

PN10011038Replace MIXER BRACKET ASSY

PN10011038

Black coffee kit Remove & Clean

MAINTENANCE SCHEDULE

(Chart continues on next page.)* indicates whichever comes first; time or servings.

8

CL & PSL50 SeriesMAINTENANCE SCHEDULE

System ComponentsSemi-annual (every 6

months/12,500 servings*) Service Tasks

Annual (every 12 months/25,000 servings*)

Service Tasks

Bi-annual (every 24 months/50,000 servings*)

Service TasksReference Instruction

Bean Hopper Bean hopper Remove & Clean See pg. 19, 28

Ingredient Canisters

Canisters and chutes Remove & Clean

CL22: Replace PN1003379 (1pcs) + PN10033780 (1pcs) + PN1009619

(2pcs)

ES12B: Replace PN10009570 (1pcs) + PN10009705 (1pcs) + PN1009619

(2pcs)

ES13: Replace PN10009562 (1pcs) + PN10009563 (1pcs) + PN10009705

(1pcs) + PN1009619 (3pcs)

FBT14: Replace PN10009562 (1pcs) + PN10009563 (1pcs) + PN10009567

(1pcs) + PN10009704 (1pcs) + PN1009619 (4pcs)

See pg. 10, 31

Yellow indicates Semi-annual (every 6 months/12,500 servings continually) Service tasks for all subsequent pages.

Green indicates Annual (every 12 months/25,000 servings continually) Service tasks for all subsequent pages.

Blue indicates Bi-annual (every 24 months/50,000 servings continually) Service tasks for all subsequent pages.

* indicates whichever comes first; time or servings.

9

CL & PSL50 SeriesSERVICE MENU

Accessing the service menu

01

Open door. Service menu will appear (access level 255 will be granted). Press Program to access basic service functions. For additional service functions, enter specific service code provided by distributor or service company.

02

Press Service On (A) to enter. Press Service Off (B) to exit. Press Return icon (C) to return to user menu.

03

A BC

10

CL & PSL50 Series

Step 1: Clean canisters, canister outlets

SERVICE TASKS

Remove canisters. Remove chutes. Close canister outlet gates by rotating so arrows point straight up (A).

Wipe exterior of canisters with dry cloth to remove any dust or spilled ingredients. For dried-on ingredients, damp cloth can be used to spot clean.

05

0201 03 04

Clean all parts inside and out. Dry after cleaning.

Pro Tip: Save time by exchanging dirty parts with clean spares and washing and drying the dirty parts later (in a dishwasher if dishwasher-safe) then reusing them during the next thorough cleaning.

Snap chutes back on. Set aside.

06 Important: For Biannual Service replace the canister units. Dispose of all used parts in the appropriate recycling bins.

CL22: Replace PN1003379 (1pcs) + PN10033780 (1pcs) + PN1009619 (2pcs)ES12B: Replace PN10009570 (1pcs) + PN10009705 (1pcs) + PN1009619 (2pcs)ES13: Replace PN10009562 (1pcs) + PN10009563 (1pcs) + PN10009705 (1pcs) + PN1009619 (3pcs)FBT14: Replace PN10009562 (1pcs) + PN10009563 (1pcs) + PN10009567 (1pcs) + PN10009704 (1pcs) + PN1009619 (4pcs)

11

CL & PSL50 SeriesSERVICE TASKS

Step 2: Clean spout adaptor, mixers, Black Coffee Kit

Remove whipper disc - one per mixer - by gripping and pulling it straight out. (Medium force is required.)

Disconnect ingredient spouts from spout adaptor.

Pull spout adaptor forward to separate it from support arm.

Release mixer by rotating red lever from 6:00 (locked) position to 7:00 (unlocked) position (A), then pull it forward to release it (B).

02 0301

A

B

04

For dispensers with Black Coffee Kit pull vessel forward to release it from mounting clip, then pull rear tube off stem.

Disassemble and clean all parts inside and out. Dry after cleaning, Set aside.

0605

Pro Tip: To make removing the whipper disc easier, a special Whipper Disc Tool is available from the distributor. (Part # 6162028)

Important: For Annual and Biannual Services replace the mixer units with PN10032974 and PN10011038. Dispose of all used parts in the appropriate recycling bins.

12


Remove red air channel. (Pay attention to location of filters, they must be reinstalled in same locations later.)

Clean all parts inside and out. Rinse filters thoroughly and squeeze to remove excess moisture. Dry after cleaning. Set aside.

0201 Important: For Annual and Biannual Services replace the air channel and filter with PN10034178. Dispose of all used parts in the appropriate recycling bins.

Step 3: Clean air channel, air filters

13

CL & PSL50 Series

Step 4: Clean espresso brewer

Slide red locking latch fully to left to unlock brewer. Disconnect water inlet tube’s quick-connect fitting.

01

Lift brewer up approx. 2-3cm to clear drive assembly and remove it from dispenser.

03

Grip brewer at top and pull forward and down so it hinges down/outwards approx. 20°/3cm.

02

Rotate espresso outlet so tube points away from centre of brewer to align retaining nib to release position, then pull it away to release it.

04

SERVICE TASKS

Wash all parts under running water and scrub away any dried coffee residue with brushes. Dry after cleaning. Set aside.

Slide cake pusher off back of brewer to separate it and fully unlock the brewer cover from the brewer (A). Then pull brewer cover out fully to separate it from brewer (B).

05

Pull brewer cover up/away from centre of brewer until it extends by 2-3cm.

06 07

A

BImportant: For Annual and Biannual Services rebuild the brewer with PN10037204. Dispose of all used parts in the appropriate recycling bins. Refer to “Install espresso brewer service kit” for instuctions.

14

CL & PSL50 Series

Step 4: Install espresso brewer service kit (annually & biannually)

Rotate exposed gear cog at back of espresso brewer until piston reaches top of cylinder.

Remove screw securing filter and seal seal to piston. Replace with new filter and seal included with kit.

0201

SERVICE TASKS

15

CL & PSL50 Series

Step 4: Reassemble espresso brewer

Insert espresso outlet so tube points away from the centre of brewer to align retaining nib to release position, then push it into brewer cover and rotate it 180° to lock it in place. Set aside.

Slide grounds pusher into its track and push it back until it just extends past the back of the brewer.

Fit brewer cover into guide slots (when correctly aligned brewer cover’s outlet tube orifice will be pointing to right - when viewed brewer from front - brewer cover cannot be successfully installed backwards).

Slide cake pusher and brewer cover towards each other so that cake pusher’s guide nibs align into brewer cover’s corresponding slots and then push brewer cover down until it is fully seated to brewer.

0201 03 04

SERVICE TASKS

16

CL & PSL50 Series

Step 5: Clean monobrewer

SERVICE TASKS

Grip monobrewer at bottom and rotate it upwards approx. 25° to release it from housing to remove it.

Disconnect monobrewer’s outlet tube. Remove safety cover.

0201 03

Important: For Annual and Biannual Services rebuild the brewer with PN10037202 (coffee versions) or PN10037220 (tea versions). Dispose of all used parts in the appropriate recycling bins. Refer to “Install monobrewer service kit” for instuctions.

04

Rotate exposed gear cog at back of monobrewer (A) so chamber base at bottom is fully opened. Then slide grounds scraper out from back (B).

B

Rotate exposed gear cog at back of monobrewer (A) so both chamber top (B) and chamber bottom (C) are both fully opened.

Slide grounds guide (A) out from back, then pull chamber top out (B). Rotate gear cog up then pull chamber bottom out (C). Wash all parts under running water and scrub away any dried coffee residue with brushes. Dry after cleaning. Set aside.

05

B

C

06

A

B

C

A

A

Pro Tip: If opening the monobrewer by rotating the gear cog at the back of the brewer proves too difficult to perform by hand, use an 8mm wrench to rotate the shaft connecting the gear sets.

17

CL & PSL50 Series

Step 5: Install monobrewer service kit (annually & biannually)

SERVICE TASKS

Press ejector button to release filter and gasket from chamber bottom. Replace with new filter and gasket included with kit.

Remove screw securing shower head and silicone plate. Pull off o-ring. Replace with new silicone plate and o-ring included with kit.

Remove o-ring from water inlet. Replace with new o-ring included with kit.

01

Pull old scraper blade off of grounds scraper. Replace with new blade included with kit.

05 0706

Slide cylinder out of bottom of brewer. Slide cylinder back into brewer. Pull silicone nipple holder out of brewer. Replace new nipple included with kit in holder and replace in brewer.

02 03 04

18

CL & PSL50 Series

Step 5: Reassemble monobrewer

SERVICE TASKS

From back of monobrewer, slide grounds scraper into its track and push it forward until scraper surface extends past chamber base.

Reinstall grounds guide (A) into its track partway. Reinstall chamber top (B) into brewer. Set aside.

Insert chamber base into bottom of brewer. Rotate exposed gear cog at back of monobrewer to adjust internal components if needed.

0201 03

A

B

19

CL & PSL50 Series

Close bean gate (push in for some models, pull out for others).

01

Step 6: Clean bean hopper

SERVICE TASKS

Remove screw securing bean hopper to dispenser housing (located at either inside front left corner of hopper or at outside bottom/front corner).

Lift entire bean hopper out of disperser.

Empty beans, then clean all accessible areas of hopper with a dry cloth. Set aside.

02 03 04

20


Step 7: Clean grinder, replace outlet

Remove grinder outlet and replace with new.

Clean around grinder area.

0201 WARNING:When working with electrical components, always turn the dispenser OFF at the main switch, or disconnect the plug from the outlet, to prevent risk of electrical shock.

21

CL & PSL50 Series

WARNING:When working with electrical components, always turn the dispenser OFF at the main switch, or disconnect the plug from the outlet, to prevent risk of electrical shock.

SERVICE TASKS

Step 8: Replace grinder soft ring (annually & biannually), adjustment ring (biannually only)

Remove grinder soft ring and replace with new.

Take note of coarseness setting, then remove adjustment ring by rotating it counterclockwise (when viewed from top) several times until it releases from grinder.

Remove remaining beans in grinder inlet, then thread on new adjustment ring to previous coarseness setting. Place new grinder soft ring on top of new adjustment ring.

0201 03

22


Step 9: Replace extractor fan (biannually only)

Remove two screws securing grinder panel at front and lift grinder assembly up and set it aside on the canister panel. Disconnect fan cable.

Lift extractor fan and manifold assembly out and remove two screws securing fan to manifold. Replace extractor fan with new. Reinstall in reverse order.

0201 WARNING:When working with electrical components, always turn the dispenser OFF at the main switch, or disconnect the plug from the outlet, to prevent risk of electrical shock.

23


Step 10: Replace fast mixer motor assembly (annually & biannually)

Disconnect canister panel via two screws at front. Rotate it up/back.

Using a long, straight screwdriver, release the two clips securing mixer motor assembly to housing. Then push mixer motor back about 1/2cm and pull it down to release it. Disconnect cable and tube connectors. Replace fast mixer motor assembly with new. Reassemble in reverse order.

0201 WARNING:When working with electrical components, always turn the dispenser OFF at the main switch and/or disconnect the plug from the outlet to prevent risk of electrical shock.

24


Step 11: Replace overpressure valve (annually & biannually)

Loosen two screws securing mixer drip panel and remove it.

Remove two screws securing high voltage safety panel and remove it.

Release overpressure valve from boiler assembly and replace with new. Reassemble in reverse order.

0201 03

Important: Ensure the water supply is turned OFF at the mains tap before removing any hydraulic system parts.

25


Step 12: Replace non-return valve (annually & biannually)

Disconnect tubes from both sides of non-return valve. Replace with new.

01

26


Step 13: Inspect inlet valve

From back of dispenser, inspect water supply tube connection for leaks/drips.

From inside dispenser, inspect inlet valve for cracks/leaks/drips.

0201

27

CL & PSL50 Series

Clean inside dispenser with kitchen cleaner. Dry after cleaning.

01

Step 14: Clean interior

SERVICE TASKS

28

CL & PSL50 Series

Replace bean hopper in position above grinder and reinstall retaining screw.

01

Step 15: Reinstall bean hopper

SERVICE TASKS

Pro Tip: Be sure the grinder soft ring is placed flat and evenly on top of the grinder inlet before reinstalling the bean hopper. A missing or misaligned soft ring will prevent sealing of the hopper to the grinder and cause a large mess inside the dispenser.

Open bean gate to restore flow (push in for some models, pull out for others).

02

29

CL & PSL50 SeriesREASSEMBLY

Step 16: Reinstall air channel and filters

Replace the air filter(s) back onto the red air channel.

Fit the air channel back into its housing, ensuring the cut-outs align with the mixer steam trap(s).

01

Note:The air channel and filters are held in place by the mixers/steam traps. The air channel must be correctly and fully reinstalled to allow the mixers/steam traps to be reinstalled correctly.

i

Pro Tip: The easiest way to ensure that the air channel is reinstalled correctly is to make sure that the cut-outs are facing out toward the front of the dispenser and downwards, and generally centred over the mixer locations.

02

30


Step 17: Reinstall spout adaptor, mixers, Black Coffee Kit

Replace steam cover back onto mixer body.

Hold red lever at 7:00 (unlocked) position and fit mixer body into mixer motor/housing (A), ensure retaining tabs and steam extractor align correctly and seat fully. Then secure mixer in place by rotating it down to 6:00 (locked) position (B).

For dispensers with Black Coffee Kit replace cover (A), connect tube to stem at the back of vessel (B), then clip vessel into bracket (C).

02 04

Align whipper disc to mixer shaft and slid it into place until it ‘clicks’. (When correctly installed approx. 1mm of shaft should extend past front of the disc).

01 03

Note:The whipper disc must align with the flat edge on the mixer shaft when reinstalling.

i

i

Pro Tip: In most cases if a mixer is very difficult to fully seat in order to lock it in place the issue is that the steam trap is not properly aligned to the air channel and/or the extractor stem, or the red locking lever is not being held at the 7:00 position, thus causing it to interfere with the mixer housing.

To resolve any of these situations, simply remove the mixer, check all alignments (steam trap, air channel, extractor stem and red locking lever) and try reinstalling it again.

A

C

BA

B

31


Step 18: Reinstall canisters

Clip the chutes back onto the canister outlets (keep the outlets pointed up for now).

01

Replace the canister(s) into the correct location(s). Make sure that the canister alignment pin is fitted into the canister shelf and sitting flush inside the dispenser.

Rotate the canister chute(s) down so that they point directly into the mixer bowl(s). Then rotate the canister lock(s) so they point straight down.

02 04

32

CL & PSL50 Series

Step 19: Reinstall espresso brewer

01 02

A

B

C

SERVICE TASKS

Reinstall espresso brewer into dispenser by hooking base of brewer onto mounting bar (A), rotating it up/back (B), then secure it with red locking latch (C).

Connect water supply tube by simply pushing it into quick connect fitting approx. 1/2cm, it locks in place automatically. Reconnect espresso brewer’s outlet tube spout to spout adaptor as close to centre of adapter as possible.

33

CL & PSL50 Series

Step 20: Reinstall monobrewer

SERVICE TASKS

Align monobrewer to drive mechanism then rotate it down to lock it in place.

01

Reconnect monobrewer’s outlet tube fitting.

02

Snap safety cover back onto front of monobrewer.

03

34

CL & PSL50 SeriesTROUBLESHOOTING

Error Code on Display Potential Cause Recommended Solution

EAB_2 Dispenser arm jammed during movement Check movement

EDC_01...15 Motor running time exceeded. Container fails to achieve set dosage (in gr). Recalibrate container

EDB_01...15 Motor current exceeding the limit value. Req.EMK-pnts could not be reached in max. allowed time.

Check container openingReplace product

EDF_01...15 Motor has jammed 3 times (sluggish)Check mixerPerform run test

EE_08 Brewer-1 movement errorReplace brewer and/or driveClose door correctly

EE_13 Brewer motor-2 not presentCheck electrical connectionsReplace brewer drive

EE_18 Brewer-2 movement errorReplace brewer and/or driveClose door correctly

EEA_01 Error while closing, sieve head blocked

Check brewer movement.Rinse toothed wheels of brewerCheck brewer assemblyClose door correctly

EEA_02 Exact closed position not reachedCheck sieve head & filterClean sieve head and brewer

Error codes, causes, solutions

35

CL & PSL50 SeriesTROUBLESHOOTING

Error Code on Display Potential Cause Recommended Solution

EEA_03 Error in motion sequence while closing

Check brewer movementRinse toothed wheels of brewerCheck brewer assemblyClose door correctly

EEA_04 Error while opening, sieve head blocked


EEA_05 Error in motion sequence while opening


EEB_01 Missing piston or brewer unhinged Hook brewer onto drive

EGN Drip tray or bucket full Empty drip tray/bucket

EDZ_02 Faulty sugar dispenser (ES dispensers) Check sugar dispenser

EDZ_03 Motor blocked during movement Check movement

Error codes, causes, solutions

36

CL & PSL50 Series

Hydraulic diagram PSL50 ES12B

SCHEMATICS

37

CL & PSL50 Series

Hydraulic diagram PSL50 ES13

SCHEMATICS

38

CL & PSL50 Series

Hydraulic diagram PSL50 FBT14

SCHEMATICS

39

CL & PSL50 Series

Hydraulic diagram CL22

SCHEMATICS

40

CL & PSL50 Series

Electrical diagram PSL50 series

SCHEMATICS

41

CL & PSL50 Series

Electrical diagram PSL50 series (continued)

SCHEMATICS

42

CL & PSL50 Series

Electrical diagram PSL50 series (continued)

SCHEMATICS

43

CL & PSL50 Series

Electrical diagram CL series

SCHEMATICS

Matchline

44

CL & PSL50 Series

Electrical diagram CL series (continued)

SCHEMATICS

Matchline

www.creminternational.com

cl & psl50 seriesdownload2.creminternational.com/spengler/10037114_03_spengler_tt_sm.pdf · 4...

Documents