Cleanliness Analysis

Enge Solutions expertise in Technical Cleanliness

Exclusive representative of Gläser GmbH

We provide training and consulting of the standards:

ISO 16232:2018 – VDA 19.1:2015

VDA 19.2:2010 - ISO 4406 – ISO 4407

Technical Cleanliness Components and Fluid Circuits

Cleanliness is nothing more than a set of standards and methods for determining the degree of soiling of each part and standardizing methods of analysis to classify acceptable particle classes into distinct components.

Automotive companies are at the cutting edge when the matter is cleanliness, and it is not new, since the accuracy of parts and systems for combustion engines and components has been perfected over the years. Nowadays, a growing number of automotive parts have specified requirements for degree of soiling, technical drawings of parts already present in, besides tolerances of dimensional codes such as CCC (Component Cleanliness Code) that the parts must meet. The main reasons for that are:

Smaller tolerances make systems more sensitive to dirt (particles); Cleaning and service life of systems and parts are correlated; Large particles can cause loss of system function.

In midst of 2005, the non-governmental organization ISO (International Organization for Standardization) established the standard ISO 16232 for extraction and analysis methods. That standard also defined which equipment is required to determine the degree of soiling of the parts. The analysis procedure begins in a controlled environment (cleanliness lab), this control refers to the temperature of the environment and the particles amount in the air, extraction and analysis equipment are specially development to determine the degree of dirtiness.

Our products and services

Cleanliness analysis of components and automotive parts, agricultural, hydraulic and fluids:

• Stereo Microscope for automatic particles counting

Jomesa GmbH.

Extraction methods available:

• Pressure Rinsing;

• Internal Rinsing;

• Ultrasonic;

• Agitation.

Gravimetric Analysis; Bilingual Report (Portuguese/English); Extraction Cabinet Gläser GmbH; Laboratory equipment and supplies.

Consulting and Training

- Training and Consulting about the standards: ISO 16232:2018,

VDA 19.1:2015, VDA 19.2:2010, ISO 4406 – ISO 4407;

- Consulting and cleanliness laboratory assembly;

- Consulting and development of cleaning processes.

Microscope Room

Laboratory 1 with clean room ISO Class 7

Cleanliness Analysis

Control and Inspection

In South America, our laboratory is the only one that performs the

test: ISO Class 7 clean room, using an extraction cabinet booth

Gläser GmbH model ACM17 along with stereo microscope for

automatic particle counting Jomesa GmbH and it is aligned with

what is the most modern when the matter is Cleanliness.

Our laboratory can analyze small and large parts.

We offer to our customers the process of extraction of dirt and

identification of metal and non-metal particles, in addition to the

gravimetric test, using international standards ISO 16232:2018,

VDA 19.1:2015, ISO 4406, ISO 4407, which are qualified by the

company Gläser GmbH (Germany) and any specifications available

in the market.

REPORT The sent report contains all the information

regarding of the method of extraction, fluid

used, equipment, a photo demonstrating

the largest metallic and nonmetallic particle

found and gravimetric result.

The report model generated by

Enge Solutions follows the European

standard.

Laboratory 2 with clean room ISO class 7

ALL IN ONE

All cleaning solution in one place:

Enge Solutions

Rua: Eçauna, 428 – Bairro: Jardim Umarizal

CEP: 05754-040 – São Paulo/SP – Brasil

+55 11 3483 – 8552

www.engesolutions.com.br

“A success story. Enge Solutions was founded in 2004 focusing on

the development of cleaning processes. After starting to represent

the German company Gläser GmbH, the largest provider of

cleanliness analysis services in Europe, China and the United

States, Enge Solutions became the largest provider of cleanliness

analysis services in South America and the unique company with

the capacity to analyze small and large parts.”

Rev. 04/2019