Part names and features

How to remove and install the QTS sleeve (torque wrench operation)

How to remove and install the QTS sleeve (sleeve installation)

How to change tuning weights

QTS sleeve performance guide

QTS sleeve position overview

Tuning weight performance guide

Important Precautions—Please Read!

P01P03P05P07P09P11P13P15

Instruction Manual / Setting AdjustmentsSRIXON Series

CLEVELAND GOLF / SRIXON5601 Skylab Rd., Huntington Beach, CA 92647, U.S.A.

Tel:1-714-889-1300 Fax:1-714-889-5890

CLEVELAND GOLF / SRIXON CANADA19099 25th Ave, #104 Surrey, BC, V3S 3V2, Canada

Tel:1-604-542-0911 Fax:1-604-542-0955

01 02

Use only the torque wrench and tuning weights provided. Use of damaged or improperly installed tuning weights may result in injury or product damage.

Change weights for fine adjustment

of Center of Gravity (CG) height

Tuning weight

QTS sleeveChange position to set desired

face angle, lie angle, and loft angle

Weight port (center) Weight port (back)

Custom torque wrenchAccessories Custom pouch

Part names and features

745945F45

Driver

Driver

Fairway wood 545 Driver

Change weights for fine adjustment

of CG depth and height

Tuning weight

QTS sleeveChange position to set desired

face angle, lie angle, and loft angle

1 2 3 4

03 04

Hold the club upright with the grip resting on the ground.

Use this position when loosening and tightening.

Supporting the head in your hand, gently insert the torque wrench into the screw hole.

Loosen Tighten

Failure to insert the tip of the torque wrench firmly into the screw hole may result in damage to the screw.

Position the torque wrench so that it is correctly aligned with the shaft.

Improperly aligned torque wrench

Shaft and torque wrench should form a straight line

Always tighten until you hear a 'click'.

Over-tightening may damage the QTS sleeve.Once you hear a 'click', stop tightening.

* Be careful not to loosen the screw too much, as you may drop the screw and lose the washer.

How to install and remove the QTS sleeve (Torque wrench operation)

Click

With the torque wrench aligned with the shaft, turn it counterclockwise.

With the torque wrench aligned with the shaft, turn it clockwise until you hear a 'click'.

Do not use any tool other than the supplied torque wrench. Also do not use the supplied torque wrench on any other products.

Screws fastening the QTS sleeve employed on the driver and fairway woods are designed for respective specifications and are not interchangeable.

Damaged QTS sleeve and/or improperly installed QTS sleeve may result in injury or product damage.* Not compatible with SRIXON Z-STAR series torque wrenches.

Failure to tighten until you hear a 'click' may result in separation of the club head or product damage.

5 6

05 06

Insert the shaft into the head

Align the position line with

the ★ mark and press straight in.* Illustration shows neutral position

For right positionAlign the ★ mark on the head with the 'R'

on the QTS sleeve and press straight in.

For left positionAlign the ★ mark on the head with the 'L'

on the QTS sleeve and press straight in.

The shaft may not insert fully if the position line and sleeve mark are not correctly aligned. Press the shaft all the way in until the QTS sleeve is completely covered.

How to remove and install the QTS sleeve (Sleeve installation)

Insertion sample

1

2 3

07 08

* Do not turn the tuning weight past the locked position.

Locked Unlocked, ready for removal

Improper installation of the tuning weight may result in injury or product damage.

Hold both the custom torque wrench and the clubhead securely while exchanging the weights.

Ensure that the tip of the custom torque wrench is fully inserted into the hole of the tuning weight.

Improper installation of the tuning weight may result in injury or product damage.Do not turn the tuning weight past the unlocked position.

Do not rotate more than 45˚.

How to change tuning weights

mark on weight

aligned with

“LOCK ” mark on head mark on weight

aligned with

“ UNLOCK” mark on head

Hold the clubhead securely in one hand

and the custom torque wrench in the other.

Insert the custom torque wrench

straight into the hole in the center of

the tuning weight and rotate it 45˚

counterclockwise to the

“ UNLOCK” position to unlock it.

Do not use any tool other than the supplied torque wrench. Also do not use the supplied torque wrench on any other products.

Pull the torque wrench directly

up to remove the weight.

* If the weight is difficult to remove even with the mark on the weight aligned with the “ UNLOCK” mark on the head, lightly jiggle and pull the tuning weight at the same time with torque wrench still inserted.

Fix the desired tuning weight on the

tip of the custom torque wrench,

insert it into the weight port,

and rotate it 45˚ clockwise to the

“LOCK ” position to lock it.

When installing or removing the tuning weights, rotate them only 45˚ until they reach the “LOCK ” or “ UNLOCK” position respectively. Do not attempt to turn the weight more than 45˚, as it may damage either the tuning weight or the weight port.

09 10

Select from 12 different positions to set your preferred face angle,

lie angle, and loft angle.

The sleeve is set to N (Neutral) at time of purchase.

Refer to the guide to set your preferred trajectory.

Lateral range of adjustment depending on sleeve position

Flight path can be adjusted laterally by approx. 37 yards (W#1)

Draw Fade

Hig

h trajectory

Low trajectory

Approx. 37 yards

QTS sleeve performance guide

10 11

12

7 2

6

9 5

3

8 1 4

NUNeutral Upright

LLeft

NNeutral

RRight

Straight face0

Open face-2.0

Straight face0

Closed face+2.0

Standard0

Moderate upright+1.0

Upright+2.0

Moderate upright+1.0

11 12

Position

Face position

ing

Lie ang

le

Initial

QTS sleeve position overview1

2 3 4 5 6 7 8 9 10 11 12

13 14

Weight port (center)

Weight port (back)

Lowering the trajectory (when ball tends to rise)

A strong trajectory when hitting into the wind and more distance with a run.

Installing a light weight on the back side creates a shallower CG which reduces spin.

Light

Installing a heavy weight on the back side creates a deeper CG that increases spin appropriately.

Raising the trajectory (when ball tends to drop)

A high trajectory that delivers distance with longer carry.

Heavy

Lowering the trajectory (when ball tends to rise)

A strong trajectory when hitting into the wind and more distance with a run.

Installing a heavy weight lowers the CG to deliver a low-spin trajectory.

Installing a light weight raises the CG to achieve the appropriate amount of spin.

Raising the trajectory (when ball tends to drop)

A high trajectory that delivers distance with longer carry.

Heavy Light

Trajectory—initial setting Trajectory after tuningg T Trajectory—initial setting Trajectory after tuningg Tg Trajectory—initial setting Trajectory after tuningg T gg Trajectory—initial setting Trajectory after tuningg T g

745945F45

Driver

Driver

Fairway wood

545 Driver

Tuning weight performance guide

To ensure a safe and satisfying golfing experience, please be sure to follow these Important Precautions.Important Precautions The manufacturer assumes no liability for injury or product damage due to failure to comply with the instructions herein.Be sure to read the Important Precautions carefully and exercise appropriate care.

Unlocked, ready for removal

Before usingCarefully inspect the QTS sleeve and tuning weights prior to each round

of golf or practice session to confirm that they are properly secured.

If the tuning weights are not secured firmly in the weight port and

you swing the club during a game or practice session, there is a danger

that a weight could fly off, injuring either you or a bystander.

1

2

Rules of GolfYou may not change the QTS sleeve position

or exchange weights during a round.

15 16

Check to see that the tuning weights are locked securely

in position.

mark on weight aligned with “LOCK ” mark on head

mark on weight aligned with“ UNLOCK” mark on head

Confirm the weight is locked in position

Tighten the sleeve until you

hear a 'click'. If you fail to

properly secure the sleeve,

there is a possibility that the

head may come off in mid

swing, injuring either you

or a bystander.

Check to see that the QTS sleeve is properly secured.

SRIXON Z Series clubs conform with R&A-approved Rules of Golf. However, it is against

the rules to modify club performance during a round by changing the QTS sleeve position

or exchanging weights to change the CG position, as this breaches the Rules of Golf

regulation 4-2a, which states: “During a stipulated round, the playing characteristics of

a club must not be purposely changed by adjustment or by any other means.”

Only remove the QTS sleeve or tuning weights when making adjustments.

All parts should remain properly installed at all other times,

including when the club is in storage, to ensure that no foreign objects

or debris become lodged in the sleeve connection or screw holes.

1

Do not heat the QTS sleeve

as it may damage the product.4

Avoid adjusting the QTS sleeve or changing weights

when the temperature is below -5˚C or above 45˚C,

as it may damage the plastic components in the weight port.

5

6

When removing the QTS sleeve or tuning weights, be sure

that you do so in a clean location to ensure that no foreign objects

or debris become lodged inside.

Installing the tuning weight while there are foreign objects

or debris in the weight port may damage either the weight

or the port, or prevent proper installation or removal

of the tuning weight.

It may even cause internal damage to the club head,

adversely affecting club performance.

2

If the QTS sleeve or weight ports become soiled

with water, dirt, or other debris, wipe them clean

with a cotton swab or a soft, clean cloth.

3

17 18

To ensure a safe and satisfying golfing experience, please be sure to follow these Important Precautions.Important Precautions The manufacturer assumes no liability for injury or product damage due to failure to comply with the instructions herein.Be sure to read the Important Precautions carefully and exercise appropriate care.

Care and storage

Please be aware that attempts to remove the QTS sleeve or intentionally

disassembling it may not comply with the manufacturer’s warranty.

* For information on manufacturer's warranty regulations,

please refer to the owner's manual and warranty included with your golf club.