cmd 2016 product catalogue
DESCRIPTION
ÂTRANSCRIPT
Ergo SolutionsPower ModulesPower DistributionLighting ControlEnergy Management
Contents
Monitor ArmsCygnus 12
Air 14
Motion 16
Motion Double 18
Vision 20
Vision Double and Triple 21
Vision Multiscreen 22
Vision Wing Arm 23
Vision Laptop Support 24
Vision Thin Client Holder 25
Vision Ceiling Pole 26
Vision Quick Release Head 27
Winston Sit - Stand Workstations 28
Unite Tablet Mount 30
Magconnect iPad Mount 31
CPU SupportsSnug 32
Enclose 33
Spin 33
Ladder 34
Cable ManagementSpiral 35
Tidy 36
Cableway 37
Fusion 38
Premium 39
Cable Eater 40
Desk Grommets 41
AccessoriesTrunking 42
Cable Clip and Clamp 42
Page 11
Content 2
Introduction 4
What We Do 6
Product Range 8
On DeskContour Metal 48
Contour 50
Harmony 52
Inca 54
In DeskPortHole 56
PortHole II USB Charging 58
PortHole III Wireless Charging 59
Wave Wireless Receiver 59
Reveal 60
Horizon 62
Affinity 64
Eclipse 66
Under DeskElite+ 68
Elite+ Data 69
Conti 70
Rotasoc 72
AccessoriesStarter Cables 84
Connector Cables 84
GST/ST Connectors 84
Earth Kits 84
Connectors 85
Locking Clips 85
Connector Blocks 85
Mains Splitter 85
Blanking Plugs 85
Fuses 85
Electrical Safety 86
Page 43Page 2
New
New
New
New
www.cmd-ltd.com 2
Contents
Underfloor PowerBetatrak 88
Tap Offs 92
Trunking Shallow Flush Floor 96
Trunking Flush Floor 98
Trunking Buried Underfloor 100
Access PowerAccess Floor Box 102
One Piece Floor Box 104
Individual Compartment Floor Box 106
Integral RCD/RCBO Floor Box 108
Slab Box 1 Compartment 110
Slab Box 2 Compartment 111
Slab Box 3 Compartment 112
Slab Box 4 Compartment 113
Screed Floor Box 114
Accessory Plates 3 Compartment 116
Accessory Plates 4 Compartment 118
Cable Hives 120
Cable Tidy Fixing Bracket 123
Grommets 124
Black Box Distribution 126
Lighting Busbar25A Lighting Busbar 128
40A Lighting Busbar 130
Technical Data 132
Page 87
Control BoxesSirius Local Switch Module 136
Proxima Basic Marshalling Box 138
Rigel Circuit Distribution Box 140
Canis Lighting Control Module 142
Sensors230v PIR Sensor 146
12V SELV PIR Sensor 148
12V SELV Microwave Sensor 150
Pre-Fabricated Wiring SystemsPre-Fabricated Accessories 152
Page 133
All images contained within this catalogue are for illustration purposes only and may be subject to change at any time.
Page 155
SystemsFootprint 156
New
3sales line: +44 (0)1709 829511
Steve Cole Managing Director
IntroductionOur Vision
Over the last three decades CMD has consistently transformed the way we integrate power and technology with furniture in the commercial world. We are inspired every day by the genuine belief that we can change the world for the better with improved ergonomics for your working environment - placing power at your fingertips or where you need it most.
On our newly designed website, www.cmd-ltd.com, you’ll find out more about CMD as a strong force in the British manufacturing world and as part of the Made In Sheffield movement. We believe in the value of community and local skills – with over 80% of our staff living in and around the Rotherham area and over 70% of all our suppliers being based in the UK. We believe in British design and manufacturing, as we lead the way in the development of USB and induction charging, but we welcome innovative design from overseas as we champion the sit-stand working revolution with introduction of Winston, our range of retrofittable single and dual screen sit-stand workstations.
100% Design
Steve Cole, Managing Director, explains, “Olympia London was a hive of excitement in September as 100% Design settled into its new home to the delight of thousands of expectant visitors. The event included exhibitors across Interiors, Design & Build, Kitchens & Bathrooms, Emerging Brands and Workplace, where CMD showcased a range of products designed to support the changing demands of offices and commercial spaces. New to CMD’s portfolio this year is Winston, the sit – stand workstation, which proved extremely popular with visitors to the stand. With a choice of colours and screen options, seamless height adjustment and a generous work surface, Winston instantly converts any desk into a sit-stand workspace.”
www.cmd-ltd.com 4
IntroductionThe Leadership Team
Jon HoldingHead of Sales
Roger ByrneHead of Production
Andy PearsonHead of Export
Bruce CantrillHead of Marketing
& New Business
Ron CooperFinance Director
Martin RourkeWarehouse Manager
5sales line: +44 (0)1709 829511
Our products have been
designed to be easy to install
over traditional cabling
systems with no requirement
for cable trays and
complicated terminations.
We also have a wide
selection of accessories, tap
offs and grommets to suit
every underfloor power and
lighting busbar requirement.
What we do
A comprehensive range of
under desk, in desk and
desktop power modules
with accessories. In desk
modules are ideal for
conference rooms. Desktop
power modules allow for
easy access for when you’re
working. Our under desk
power solutions range
from the affordable, to the
more flexible metal based
extrusion which can be fed
from our underfloor power.
Create healthier workplaces
that improve performance
and bring greater
productivity. Deliver a
more streamlined and
aesthetically appealing space
whether in the office, at
home or on the move. This
section includes monitor
arms, CPU supports, cable
management solutions and
accessories.
www.cmd-ltd.com 6
Our control boxes with
accessories offer a simple
‘plug and play’ system
giving you a fast install
when you need it most.
This minimises terminals to
guarantee reduced on site
commissioning.
We are aBritish manufacturer
founded in 1984, whocreate solutions to meet
the challenges of integrating power and technology with
furniture for commercial environments
What we do
7sales line: +44 (0)1709 829511
On Desk Power Modules
Under DeskPower Modules
Lighting SensorsControl Boxes
Access Power
Power Distribution
Product range
www.cmd-ltd.com 8
In Desk Power Modules EnergyManagement
CPU Supports
CableManagement
Monitor Arms
Product range
9sales line: +44 (0)1709 829511
Bespoke solutions.
As well as being market-leading providers of ergonomic solutions, power modules, power distribution and lighting
control we provide bespoke products power module solutions across a number of configurations and environments
to suit specific needs.
Our specialist engineering team span multiple disciplines and are united by their shared enthusiasm for quality
solutions. The combination of our deep electrical knowledge and innovative application of new technology enables
us to deliver real benefits: helping our customers to work more effectively and delivering power to exactly where they
want it with a wide range of options to improve their efficiency.
We deliver a range of products and solutions which include:
• USB charging & data transfer
• Induction charging (Qi Technology)
• Audio & Visual options (HDMI, VGA, Phono and much more)
• Every level of data
• International sockets
• Protection
• Switching
We are extremely proud of our heritage and have been producing customer led solutions since 1984. The image
below shows a bespoke module that was specifically designed to be fitted into the arm of a sofa to provide power
and USB charging.
Product range
www.cmd-ltd.com 10
Mountingkit
included
Cygnus® is our award winning gas lift flat screen monitor arm featuring a unique blend of innovative engineering and contemporary styling. It offers all the benefits you would expect of a premium adjustable gas lift arm with the added benefit of an extensive range of useful features to further enhance its function making life in a busy working office more comfortable and aesthetically pleasing. Cygnus® is available in a range of colour options with a choice of gas struts for when you need a more heavy duty arm.
Cygnus® flat screen arm
Arm supports up to 10kg or 14kg
(two gas struts available)
Integrated cable management
Quick release head
VESA compliant 75mm and 100mm
• An integral gas strut counterbalances the weight of the screen allowing fingertip adjustment to the desired working position
• The arm mechanism ensures the screen remains vertical throughout any adjustment
• The dual-position forearm can be set at 15° or 45° positions to extend the operational range of the arm giving a maximum height of 523mm and a maximum reach of 476mm to the centre of the VESA plate.
• The arm can fold flat into 80mm of space• The tilt and rotate head features a quick-release
mechanism with a locking feature as standard permitting quick and easy monitor detachment
• Arms are supplied with an industry standard 75mm / 100mm VESA mounting plate for attachment of monitors
• The arm features an integral cable management system • Includes C clamp and Bolt Through fixing kit• Product weight 5kg
C clamp
43m
m
98.5
mm
40mm
Gas monitor armCygnus
www.cmd-ltd.com 12
Cygnus® flat screen arm
Universal Slatwall Monitor Arm Bracket
This universal bracket is ideal when desk space is at a premium as it fits directly to the slatwall rather than to the desk surface.
80mm Grommet Mount for Cygnus® arm
Designed to fit an 80mm desk grommet hole as an alternative to our standardC clamp and bolt through or fixing kits.
Cygnus® mounting options:
Razor Mount - For whenyou need two screens
Double head mount designed to hold two screens on one Cygnus® arm must be used in conjunction with 80K152, 68F121 & 68F143. Monitor weight should not be more than 6kg each.
BlackSilver White
Code Colour Description
68F017 Silver Cygnus® gas lift arm with C clamp and Bolt Through fixing kits. Holds screen weights 3-10kg
68F120 Black Cygnus® gas lift arm with C clamp and Bolt Through fixing kits. Holds screen weights 3-10kg
68F031 White Cygnus® gas lift arm with C clamp and Bolt Through fixing kits. Holds screen weights 3-10kg
80K152 Silver Cygnus® gas lift arm with C clamp and Bolt Through fixing kits. Holds screen weights 8-14kg
68F121 Black Cygnus® gas lift arm with C clamp and Bolt Through fixing kits. Holds screen weights 8-14kg
68F143 White Cygnus® gas lift arm with C clamp and Bolt Through fixing kits. Holds screen weights 8-14kg
68M074 Silver Razor mount. Holds screen weight of 6kg each side. Arm not included
68M075 Black Razor mount. Holds screen weight of 6kg each side. Arm not included
68M076 White Razor mount. Holds screen weight of 6kg each side. Arm not included
440324 Silver 80mm grommet mount for Cygnus®. Arm not included
440326 Black 80mm grommet mount for Cygnus®. Arm not included
440325 White 80mm grommet mount for Cygnus®. Arm not included
440269 Silver Universal slatwall bracket for Cygnus®. Arm not included
440506 Black Universal slatwall bracket for Cygnus®. Arm not included
440380 White Universal slatwall bracket for Cygnus®. Arm not included
13sales line: +44 (0)1709 829511
Gas monitor armAir
Air flat screen arm
Gas strut supports upto 8kg monitors
Cable management
Optional C clamp or bolt through fixing kit
Quick release head
VESA compliant 75mm and 100mm
Lock at specific angles
Gas assisted fingertip movement
• An integral gas strut counterbalances the weight of the screen allowing fingertip adjustment to the desired working position
• The arm mechanism ensures the screen remains vertical throughout any adjustment
• The arm can fold flat into 80mm of space• The tilt and rotate head features a quick-release
mechanism with a locking feature as standard permitting quick and easy monitor detachment
• Arms are supplied with an industry standard 75mm/ 100mm VESA mounting plate for attachment of monitors
• The arm is supplied with cable management clips
www.cmd-ltd.com 14
Air has been designed with the environment in mind, built and made in Sheffield, the home of UK manufacturing. Air projects a clean and slimline exterior where functionality is prevalent yet style is not forgotten. It provides optimum performance expected from a gas assisted monitor arm using locally designed and sourced parts. Air has the range of articulation of our award winning Cygnus® arm enabling your screen to be set up according to the requirements of your working environment. Gas assistance allows the arm to move freely and effortlessly across the desk when adjusting your screen to your natural position.
Air flat screen arm
BlackSilver White
Code Colour Description
80K661 Silver Air monitor arm with C clamp fixing kit
80K662 Black Air monitor arm with C clamp fixing kit
80K663 White Air monitor arm with C clamp fixing kit
80K664 Silver Air monitor arm with Bolt Through fixing kit
80K665 Black Air monitor arm with Bolt Through fixing kit
80K666 White Air monitor arm with Bolt Through fixing kit
Slatwall options are available on request, please call the Sales Office.
C clamp
50m
m
78.5
mm
143m
m
15sales line: +44 (0)1709 829511
Pole monitor armMotion
Motion flat screen arm
Arm supports up to 8kg monitors
Cable management
Optional C clamp orbolt through fixing kit
Quick release head VESA compliant 75mm and 100mm
Height adjustment
• Common styling with Air monitor arm• Minimal design, with linear styling• Folds back flush to screen or desk back
edge• Button release lift and lower mechanism• Arms are supplied with an industry
standard 75mm / 100mm VESA mounting plate for attachment of monitors
• Quick release VESA plate fixing as standard• VESA plate screen lock security mechanism• Available in single or double configurations• 35mm diameter pole
www.cmd-ltd.com 16
Motion is the ever practical pole arm that offers the ergonomic benefits of a monitor arm yet more affordable than its more prestigious Air gas sibling.
Motion does share common styling with Air ensuring the aesthetics are not comprised when the arms share the same floor space.
Motion is available as a single or double arm making it ideal for those who work in close proximity or for the individual user who has two screens. It can also be selected with a monitor head that is ideal for reception areas and point of sale locations.
Motion flat screen arm
Code Colour Description
80K655 SilverMotion monitor arm with C clamp fixing kit
80K656 BlackMotion monitor arm with C clamp fixing kit
80K657 WhiteMotion monitor arm with C clamp fixing kit
80K658 Silver Motion monitor arm with Bolt Through fixing kit
80K659 Black Motion monitor arm with Bolt Through fixing kit
80K660 White Motion monitor arm with Bolt Through fixing kit
BlackSilver White
Slatwall options are available on request, please call the Sales Office.
C clamp
50m
m
78.5
mm
143m
m
17sales line: +44 (0)1709 829511
C clamp fixing kitor bolt through fixing kit
Height Adjustment
Motion double flat screen armMotion Double is ideal for when you need two screens mounted at the same height to achieve the perfect ergonomic setup.
Code Colour Description
80K667 Silver Motion Double monitor arm with C clamp fixing kit
80K668 Black Motion Double monitor arm with C clamp fixing kit
80K669 White Motion Double monitor arm with C clamp fixing kit
80K670 Silver Motion Double monitor arm with Bolt Through fixing kit
80K671 Black Motion Double monitor arm with Bolt Through fixing kit
80K672 White Motion Double monitor arm with Bolt Through fixing kit
BlackSilver White
Quick release head
Supports up to 8kg monitors
www.cmd-ltd.com 18
Motion single head
Motion 400mm poleThe Motion 400mm pole removes the extending arm for environments where it’s not suitable or simply the pole and head will suffice. This is perfect for spaces where fixed screens are required and height adjustment is still needed.
Bolt throughfixing kits
available uponrequest
Motion Twin Head
Suitable for receptions,
check in, retail, touch
screens, trade desks.
Height adjustableCable management
Note: other pole lengths are available on request.
Code Colour Description
80K673 Silver Motion single head monitor arm with C clamp fixing kit
80K674 Black Motion single head monitor arm with C clamp fixing kit
80K675 White Motion single head monitor arm with C clamp fixing kit
80K676 Silver Motion twin head monitor arm with C clamp fixing kit
80K677 Black Motion twin head monitor arm with C clamp fixing kit
80K678 White Motion twin head monitor arm with C clamp fixing kit
Other pole lengths available on request
19sales line: +44 (0)1709 829511
45.5mm
62m
m
C clamp
Vision flat screen armVision is a design classic monitor arm which offers the ergonomic benefits of a flat screen monitor arm yet is more affordable than its more prestigious gas lift rivals. Vision can be installed at different heights to suit different environments with rotation and height adjustments being made by the individual users. The 38mm diameter pole allows a huge 330mm of height adjustment, while the design also allows a full 360 degrees of swivel movement with full head tilt to be positioned at the optimum eye level.
VESA compliant 75mm and 100mm
Arm supports monitors up to 8kg
Height adjustment
Cable management
• Each single arm can support monitors up to 8kg
• The maximum extension of each single arm is 460mm when measured from the centre of the Vision pole to the centre of the VESA mount
• The monitor can be attached using the 75mm or 100mm VESA compliant mount
• Cable management clips are supplied and can be attached to the arm as required
• Available in silver, black and white (Note: Our slatwall and wall mounted systems are only available in silver)
460mm maximum extension
88m
m
177m
m
400mm Pole
Pole monitor armVision
www.cmd-ltd.com 20
Vision flat screen arm
Single Arm
Double Arm
Triple Arm
Code Colour Description
68S002 Silver
Single Vision pole arm with C clamp, Bolt
Through, and 80mm Grommet fixing kit.
With black plastic trim
68S020 Black
Single Vision pole arm with C clamp, Bolt
Through, and 80mm Grommet fixing kit.
With black plastic trim
68S028 White
Single Vision pole arm with C clamp, Bolt
Through, and 80mm Grommet fixing kit.
With white plastic trim
Single Arm
Code Colour Description
68S005 SilverDouble Vision pole arm with C clamp, Bolt Through, and 80mm Grommet fixing kit.
With black plastic trim
68S031 BlackDouble Vision pole arm with C clamp, Bolt Through, and 80mm Grommet fixing kit.
With black plastic trim
68S018 WhiteDouble Vision pole arm with C clamp, Bolt Through, and 80mm Grommet fixing kit.
With white plastic trim
Double Arm
Code Colour Description
68S078 Silver
Triple Vision pole arm with C clamp, Bolt Through,
and 80mm Grommet fixing kit.
With black plastic trim
68S099* Black
Triple Vision pole arm with C clamp, Bolt Through,
and 80mm Grommet fixing kit.
With black plastic trim
68S100* White
Triple Vision pole arm with C clamp, Bolt Through,
and 80mm Grommet fixing kit.
With white plastic trim
Triple Arm
Our Double Vision kit allows for two screens to be mounted and adjusted as required. Each VESA head supports monitors up to 8kg.
Our Triple Vision kit allows for three screens up to 17” to be mounted and adjusted as required. Each VESA head supports monitors up to 8kg.
Our Single Vision kit allows for a single screen to be mounted and adjusted as required. Arm supports monitors up to 8kg.
*Subject to order quantities and lead times.
Note: Arm supports monitors up to 8kg.The alignment of some double screen and multiscreen systems may vary with an accepted tolerance of +/- 5mm.
21sales line: +44 (0)1709 829511
Our 4 screen Vision kit allows for four screens to be mounted and adjusted as required. Each arm supports monitors up to 8kg.
Vision flat screen arm
4 screen system
Code Colour Description
68S093 Silver
4 screen Vision pole arm with C clamp, Bolt
Through, and 80mm Grommet fixing kit.
With black plastic trim
68S094 Black
4 screen Vision pole arm with C clamp, Bolt
Through, and 80mm Grommet fixing kit.
With black plastic trim
68S095 White
4 screen Vision pole arm with C clamp, Bolt
Through, and 80mm Grommet fixing kit.
With white plastic trim
4 screen system
Code Colour Description
68S096 Silver
6 screen Vision pole arm with C clamp, Bolt
Through, and 80mm Grommet fixing kit.
With black plastic trim
68S097* Black
6 screen Vision pole arm with C clamp, Bolt
Through, and 80mm Grommet fixing kit.
With black plastic trim
68S098* White
6 screen Vision pole arm with C clamp, Bolt
Through, and 80mm Grommet fixing kit.
With black plastic trim
6 screen system
Our 6 screen Vision Kit allows for six screens up to 17” to be mounted adjusted as required. Each arm supports monitors up to 8kg.
6 screen system
Code Colour Description
68S024 SilverSingle Vision pole arm with slatwall mounting and
black plastic trim
68S106 White Single Vision pole arm with slatwall mounting
Slatwall system
Code Colour Description
68S004 SilverSingle Vision pole arm with wall mounting kit and
black plastic trim
Wall mounted system
Wall mounted system
Note: Arm supports monitors up to 8kg.
Note: Arm supports monitors up to 8kg.The alignment of some double screen and multiscreen systems may vary with an accepted tolerance of +/- 5mm.
*Subject to order quantities and lead times.
www.cmd-ltd.com 22
Vision accessories
Vision wing arm
Used in conjunction with our Vision single pole, the new wing arm can be adjusted to support a wide range of monitor sizes.
Single Vision pole sold separately
Sliding mechanism to adjust for different
sized monitors
Code Colour Description
68S114 Silver Vision wing arm with adjustment Vesa
68S115 Black* Vision wing arm with adjustment Vesa
68S116 White Vision wing arm with adjustment Vesa
Available in silver, black and white (subject to MOQ)
Our Vision wing arm can be purchased with our single pole to create an double monitor system or retro fitted to your existing Vision pole.
The position of the Vesa head can be adjusted using a simple thumb screw. Each Vesa head can be adjusted up to 125mm to support different sized monitors.
340mm to 590mm
Note: The Vision arm is not included with the Vision wing arm.
* Subject to availability and lead times.
23sales line: +44 (0)1709 829511
Vision accessories
Used in conjunction with the Vision pole arm the laptop holder can be positioned to the side or rotated around the pole and height can be adjusted with a simple release mechanism.
• Laptop holder will hold up to 8kg• Tray features a non-slip surface with adjustable
platforms for wider laptops• 360o rotation around the Vision pole arm• 330mm height adjustment range• 90o pan adjustment• 40o tilt adjustment range
Laptop support
Code Colour Description
50N001 SilverVision Laptop Support
with black lever
50N002 BlackVision Laptop Support
with black lever
50N003 WhiteVision Laptop Support
with white lever
50N004 WhiteVision Laptop Support
with black lever
Available with black or white lever
Vision pole issold separately
Arm supports up to 8kg
Non-slipsurface
www.cmd-ltd.com 24
Vision accessories
Code Colour Description
58R018 Silver Vision Thin Client Holder
58R016 Black Vision Thin Client Holder
58R017 White Vision Thin Client Holder
Used in conjunction with the Vision pole arm the thin client holder can support a variety of thin client sizes. The Vision pole arm can be supplied with an extended C clamp base if needed to allow the holder to be used with desk privacy screens - please ask for details.
Designed to support thin clients with a minimum height of 150mm, a maximum height of 235mm, maximum width of 300mm and maximum depth of 60mm.
Thin client holder
50mm
70m
m85
mm
150m
m
235m
m
Dimensions
Vision pole arm(purchased separately)
Adjustable base plate
Extended C clamp base for use with privacy screens.
(available on request)
• Easy Fixing - Can be fitted to your existing Vision pole monitor arm or bought together for new installations.
• Strong Construction - Constructed from 2mm powder coated steel making this an affordable and robust solution for thin client users.
• Versatility - The Vision thin client holder is fully adjustable and can accommodate a wide range of thin client sizes.
Note: The Vision arm is not included with the Vision thin client holder.
25sales line: +44 (0)1709 829511
VESA compatible fixing holes
(75mm/100mm)
Gravity hook
Strong 2mm painted metal construction
Quick fitting securing lever
Stability brackets
Vision accessories
Quick release VESA
Code Colour Description
68S071 Silver Vision Quick Release VESA
68S101 Black Vision Quick Release VESA
68S102 White Vision Quick Release VESA
Code Colour Description
68S059 Silver 400mm Pole with C clamp, Bolt Through and 80mm Grommet fixing kit with black cap
68S060 Black 400mm Pole with C clamp, Bolt Through and 80mm Grommet fixing kit with black cap
68S061 White 400mm Pole with C clamp, Bolt Through and 80mm Grommet fixing kit with black cap
68S062 White 400mm Pole with C clamp, Bolt Through and 80mm Grommet fixing kit with white cap
68S085 Silver 750mm Pole with C clamp, Bolt Through and 80mm Grommet fixing kit with black cap
68S086 Black 750mm Pole with C clamp, Bolt Through and 80mm Grommet fixing kit with black cap
68S087 White 750mm Pole with C clamp, Bolt Through and 80mm Grommet fixing kit with white cap
Code Colour Description
68S067 Silver Single Head
68S088* Black Single Head
68S089* White Single Head
Vision poles
Single head
*Subject to order quantities and lead times.
www.cmd-ltd.com 26
Vision ceiling pole
Standard Vision single head sold
separately
Ceiling pole arm
Ceiling fixing
Allen key adjustment
Available in black, white and silver
390m
m t
o 69
5mm
50m
m
Code Colour Description
68S117 Silver Vision ceiling pole with height adjustment
68S118 Black* Vision ceiling pole with height adjustment
68S119 White* Vision ceiling pole with height adjustment
Used in conjunction with our Vision single head, the new ceiling pole arm can be adjusted to support a wide range of TVs and monitors.
Note: The Vision single head is not included with the Vision ceiling pole. See page 43 for details.
* Subject to availability and lead times.
VESA compliant 75mm and 100mm
27sales line: +44 (0)1709 829511
Winston sit - stand workstation
Single monitor systemWinston
All black All white Rear view
Height adjustment
Code Colour Description
68W85304 Black/Silver Winston Single, Freestanding, Black/Silver. Light (4.1-9.1 kg). Black work surface. Silver column.
68W85305 Black/Black Winston Single, Freestanding, Black/Black. Light (4.1-9.1 kg). Black work surface. Black column.
68W85306 White/White Winston Single, Freestanding, White/White. Light (4.1-9.1 kg). White work surface. White column.
• Instantly converts any desk into a sit-stand workspace
• Engineered to reduce unwanted movement• Large surface area (76.2cm x 58.4cm) with
convenient storage tray that allows you to bring everything you need with you when you stand
• Features a 40cm range of vertical height adjustment and locking mechanism to keep the workstation in position
• Includes integrated cable management clips
NewProduct
www.cmd-ltd.com 28
Winston sit - stand workstation
Dual monitor systemWinston
Black/Silver All white Rear view
Cable management
Code Colour Description
68W85307 Black/Silver Winston Double, Freestanding, Black/Silver. Medium (5.4-12.7 kg). Black work surface. Silver column.
68W85308 Black/Black Winston Double, Freestanding, Black/Black. Medium (5.4-12.7 kg). Black work surface. Black column.
68W85309 White/White Winston Double, Freestanding, White/White. Medium (5.4-12.7 kg). White work surface. White column.
NewProduct
29sales line: +44 (0)1709 829511
Unite™ tablet mount
Unite
Unite Clamp Mount 68J001C clamp desk mounting
for quick installation
Finger tightening mechanism for adjusting
the mount’s position
Lightweight carbon fibre sections
5 point fixing system to support tablets
from 7” - 10”
These award-winning mounts are now available from CMD and are the perfect mounting solutions for any 7”-10” tablet displaying it at the perfect angle for utmost convenience.
The clamp attaches to the widest variety of surfaces (10-40mm), round or flat. Its single carbon fibre arm is perfect for whenever you need to keep your tablet nearby but not in your hands.
And with more and more people using tablets as business tools, Unite provides a hands-free solution that increases efficiency and positions the tablet at the optimum ergonomic height and angle for safe and stress free use.
Omni-directionalball joints
www.cmd-ltd.com 30
MagConnect™ iPad mount
Code Colour Description
68J001 Black Unite™ Universal Carbon Fibre Single Section Clamp Mount for Tablets
68J002 Black Unite™ Universal Carbon Fibre Double Section C clamp Mount for Tablets
68J003 Black Unite™ Universal Carbon Fibre Wall/Cabinet Mount for Tablets
68J004 Black MagConnect™ Technology Clamp Single Section Mount for iPad 2nd/3rd/4th Generation
68J005 Black MagConnect™ Technology Double Section C clamp Mount for iPad 2nd/3rd/4th Generation
68J006 Black MagConnect™ Technology Wall/Cabinet Double Section Mount for iPad 2nd/3rd/4th Generation
Magconnect™ Wall/Cabinet Mount 68J006
Lightweight StrengthUnite and Magconnect mounts are built of high-quality carbon fibre. This advanced material is surprisingly lightweight yet incredibly strong. The powerful combination of carbon fibre with carefully designed joints produces mounts that are both easy to manoeuvre and sturdy to use.
Omni-directional Ball JointUnite and Magconnect mounts come equipped with omni-directional ball joints for ultimate customisability. The tablet/ iPad holder can be swivelled 360° to ease the transition from portrait to landscape mode without removing it from the mount. And the sturdy carbon fibre arms can also be adjusted into infinite configurations providing you with the perfect angle every time.
MagConnect
MagConnect™ C clamp Mount 68J005
Technology for an easy, secure connection every time for tablets.MagConnect™ is the next step in the evolution of mobile mounts and includes a locking mechanism to provide the perfect mounting solution.
The technology is advanced but simple to use. First, the iPad is secured into a hard-shell case equipped with a powerful magnet. When the case is attached to a compatible product, another magnet instantly interlocks your MagConnect™ shell with a receiver, while a precision screw tightens for a secure fit.
31sales line: +44 (0)1709 829511
CPU supportSnug is a simple and stylish CPU support that enhances the aesthetics of any workspace environment and allows easy access to the front and back of the CPU.
Variable height adjustment
Smart aesthetic cover• Slim and stylish design• Simple to install• Available in various colours• ABS fascia cover fits on to metal structure
giving a smart aesthetic look• Extender plate included as standard for wider
CPUs• CPU sits on a metal platform and is secured
in place with a strap• CPU dimensions range:
275mm - 420mm (H) x 96mm - 190mm (W) • Load tested by FIRA• Supports CPU weights up to 10kg - subject
to desk material• Product weight 3.44kg
LOAD TESTED
Optional Slide and Rotate allows movement of the CPU holder for Snug and Ladder.
Slide mechanism requires a minimum desk width of 700mm (Track length 407mm).
Code Colour Description
58A109 Black Body with Metallic Silver Frame Snug Adjustable CPU Support
58A122 White Body with Metallic Silver Frame Snug Adjustable CPU Support
58A162 Grey Body with Metallic Silver Frame Snug Adjustable CPU Support
58A049 Black and Silver Slide and Rotate Mechanism
Snug CPU support
www.cmd-ltd.com 32
CPU supportDesigned to enhance any office environment with its modern aesthetics and compact features, the Enclose CPU holder is simple to install and a robust solution for keeping the CPU out of the way and free from damage. Poised under the desk, Enclose improves the CPU performance by facilitating improved ventilation promoting a longer life for CPUs by allowing hardware to stay cool and vent freely as well as removing CPUs off the floor where dust accumulates and valuable computer equipment could be kicked or damaged by a vacuum cleaner. Made from high quality aluminium for improved lifetime longevity, simple handle adjustment for either height or width exact fitting and a full 360° slide and rotation feature makes Enclose the only choice for your next CPU holder.
Spring loaded aluminium body clamps the CPU
securely in place
Slide & 360o Rotation
Adjustable bracket supports CPUs
of different widthsCode Description
58R011 Enclose CPU Support
• CPU dimensions range: 280mm - 380mm (H) x 55mm - 125mm (W)
• Supports CPU weights up to 8kg - subject to desk material
• High quality aluminium with simple handle adjustment
• Full 360o slide and rotate mechanism
Spin cpu supportCode Description
58R010Spin CPU Holder. Complete with slide and rotate mechanism
58R009Lockable Spin CPU Holder. Complete with slide and rotate mechanism. 2 sets of keys included
Spin CPU Support
• Adjustable support platform to accommodate extensive CPU sizes • Max dimensions: 380mm - 580mm (H) x 50mm - 275mm (W)• Supports CPU weights up to 15kg - subject to desk material• Comes complete with a slide and rotate mechanism
Spin Lockable CPU Support
• Locking mechanism built for security comes with 2 sets of keys• Slideable and 360o rotation• Max dimensions: 370mm - 570mm (H) x 110mm - 230mm (W)• x 295mm - 540mm (D)• Supports CPU weights up to 15kg - subject to desk material
The clamp can be adjustedto fit a variety of widths
Slideable & 360o Rotation
Enclose CPU support
33sales line: +44 (0)1709 829511
Single Ladder• Adjustable support platform to
accommodate different CPU sizes and mounting heights
• A strap secures the CPU permitting easy removal for servicing or replacement
• Mounting bracket screws directly into the underside of the work surface
• Optional slide and rotate mechanism• Can be adapted to fit to beam based
furniture if required• Max dimensions:
500mm (H) x 130mm (W)• Supports CPU weights up to 15kg -
subject to desk material
Ladder is a stylish and functional solution for CPUs with its steel frame it supports the CPU together with the strong nylon strap used to secure the CPU in position.
Optional Slide and Rotate allows movement of the CPU holder for Snug and Ladder.
Slide mechanism requires a minimum desk width of 700mm (Track length 407mm).
Double Ladder • Double Ladder supports 2 CPUs side by
side
Ladder CPU support
Code Colour Description
58A192 Silver Single Ladder CPU Holder with Strap
58A193 White Single Ladder CPU Holder with Strap
58A194 Silver Double Ladder CPU Holder with Strap
58A195 White Double Ladder CPU Holder with Strap
58A049 Black/Silver Slide and Rotate Mechanism
Rainbow CPU Trolley
Code Colour Description
58A190 Silver Rainbow CPU Trolley
Double ladder
www.cmd-ltd.com 34
Spiral cable spine
This unique desk to floor cable management spine offers exceptionally quick and easy installation plus a large cable carrying capacity and a good aesthetic appearance.
SilverBlack White
Code Colour
660132 Black
660133 White
660130 Silver
Cable exit
Spring like expansion from 150mm to 1300mm
Large capacity to accommodate a number of
different sized cables
Simple install by single screw into desktop
Weighted horseshoe
Cable exit29mm (H) x 50mm (W)
Fits 25mm conduit
Diameter 69mm
35sales line: +44 (0)1709 829511
This innovative fabric design deals with the everyday problem of cable management with a simple and flexible solution that fits a wide range of desk systems.
Tidy is extremely versatile, lightweight and easy to install. The zip and segregation channels allow all power and data cabling to be concealed yet segregated whilst the fabric hook and loop fixing straps allow you to cater for a range of desk heights.
• Adjustable height from 690mm to 790mm to cater for different desk heights
• Each unit is made from a high quality fabric which gives it fabulous strength and flexibility
• Available in black, white and grey• Product weight 500g
Note: The desk fixing bracket and weighted foot are coloured to match the product.
Tidy™ cable spine
Code Colour Description
650802 Black 690mm to 790mm with black zip
650803 White 690mm to 790mm with white zip
650804 Grey 690mm to 790mm with grey zip
Desk fixing bracket
Internal segregation
Adjustable fabric hook and loop fixing straps
Zip opening
Adjustable fabric hook and loop fixing straps
Weighted foot
Black White
Cable Tidy Fixing
Code Colour Description
PPH22260G Grey Cable Tidy fixing for use with Standard Cable Hive
Grey
www.cmd-ltd.com 36
Cableway cable spineAn attractive and practical method of cable containment. The Cableway routes cables from floor to desk and provides mechanical protection and strain relief.
• Two compartments to allow for power and data cable segregation
• Weighted base for free standing floor to desk section
• Internal channel allows 3 pole connectors through
• Allows conduit up to 25mm diameter to be swiped in
• Segments are detachable for easy re-configuration
• The Vertical Cableway screws to underside of the desk using a top bracket (Fixing kit included)
• The Horizontal Cableway screw to the underside of the desk using clip-on fixing brackets (Fixing kit included)
Code Colour Description
660181 WhiteVertical Cableway weighted base to desk including top bracket.(Approx height 780mm)
660042 SilverVertical Cableway weighted base to desk including top bracket.(Approx height 780mm)
660182 White Horizontal Cableway. (Approx length 620mm)
660050 Silver Horizontal Cableway. (Approx length 620mm)
660183 WhiteExtended Cableway weighted base to desk including top bracket. (Approx length 1340mm)
660046 SilverExtended Cableway weighted base to desk including top bracket.(Approx length 1340mm)
Extended Cableway
Horizontal Cableway
Under desk clip-on fixing bracket
25mmdiameter
28mm
Cable Section
Easy tore-configure
Power and data segregation
Weighted base
(Vertical Cablewaynot included)
37sales line: +44 (0)1709 829511
Fusion is a high-capacity polypropylene coated wire cable management system. Fusion features a sloping side for easy access to cables and specially designed hook brackets to guarantee a simple and quick installation. Fusion can easily be attached to the underside of the desk or to the modesty panel.
Fusion cable basketCode Description
650468800mm (actual length 766mm)includes x2 Brackets
6504691000mm (actual length 994mm) includes x2 Brackets
6504701200mm (actual length 1146mm)includes x2 Brackets
6504711400mm (actual length 1375mm)includes x2 Brackets
6505341600mm (actual length 1527mm)includes x2 Brackets
Silver low density polypropylene coated wire
Code
251904
Additionalbracket
Dimensions
100mm
104m
m
138mm
132m
m
Earthing point
Specially designed brackets to stop basket from being knocked out accidentally
Slanted front for cable and plug access
Silver RAL 7040
www.cmd-ltd.com 38
* White Premium cable baskets are available on request, subject to lead times and a minimum order quantity. 2000mm lengths are available on request.
Premium cable BasketPremium is a simple cable containment basket which clips underneath the desk and routes power and data cables neatly under the desk surface. Basket width (150mm) and basket height (85mm).
Code Colour Description
650756 Silver Premium cable basket (1000mm) includes x2 Brackets
650757 White* Premium cable basket (1000mm) includes x2 Brackets
650758 Silver Premium cable basket (1200mm) includes x2 Brackets
650759 White* Premium cable basket (1200mm) includes x2 Brackets
650760 Silver Premium cable basket (1400mm) includes x2 Brackets
650761 White* Premium cable basket (1400mm) includes x2 Brackets
650762 Silver Premium cable basket (1600mm) includes x2 Brackets
650763 White* Premium cable basket (1600mm) includes x2 Brackets
650764 Silver Premium cable basket (1800mm) includes x2 Brackets
650765 White* Premium cable basket (1800mm) includes x2 Brackets
650128 Black Additional x1 Strap hinge bracket
112m
m
142mm
90m
m
Specially designedbrackets
Silver RAL7040 or White* RAL 9010 on request
Mild steel nyloncoated wire basket
Earthing point
70mm
39sales line: +44 (0)1709 829511
Cable eaterCable eater is the quick and easy solution for organising and streamlining your untidy cables. Suitable for home or workspace, using the insertion tool, a number of cables can be speedily zipped into the strong flexible casing. Commercial reels can be cut to length to suit the needs on site.
Code Colour Description
650101 Grey Cable Eater 30m & Zip Tool
Cable eater can be cut with ease for anylength of usage
Hand tool supplied for quick and easy
installation
20mm diameter
www.cmd-ltd.com 40
80mm Metal Desk GrommetsA high quality cast aluminium desk grommet available in polished, brush nickel and matt chrome finish. Brush strip on cable entry port. The unit features a twist lock action to retain the lid. Easily retro fitted into an 80mm diameter hole. Minimum work surface thickness is 12mm.
80mm Plastic Desk GrommetsA high quality plastic desk grommet. Easily retro fitted into a 80mm diameter hole. Minimum work surface thickness is 22mm and has a removable slide that can be stored in a recess under the cover plate.
Desk grommets
SilverWhiteBlack
Code Colour Description
520168 Polished 80mm Desk Grommet
520169 Brushed Nickel 80mm Desk Grommet
520170 Matt Chrome 80mm Desk Grommet
Matt ChromeBrushed NickelPolished
80mm desk grommets
• Cover plate conceals all the cables below the desk top• Cover is removable to allow the introduction of cables with a fitted plug
47m
m
97m
m
80m
m
25mm
20mm
90m
m
80m
m
13.5mm
12mm
22m
m
75m
m
Code Colour Description
520001 Black 80mm Desk Grommet
520162 White 80mm Desk Grommet
520145 Silver 80mm Desk Grommet
41sales line: +44 (0)1709 829511
Hi-tech Trunking • Solves the problem of untidy cabling• Three separate channels for power, voice and data segregation• Two piece swipe through T-shaped strips for addition or
removal of cables• Cutting service is available for non-standard lengths• Self-adhesive backing strip• Can be drilled and screw mounted• Colour Black
Flexible Cable Trunking • Simple means of keeping cables tidy• Suitable for use on furniture, control gear and enclosures• Available in three sizes• Supplied in 500mm lengths• Slip ring for quick addition or removal of cables• Self-adhesive backing strip• Colour White
Cable Clip • Handy clip providing a simple method of holding cables• Self-adhesive fixing• Colour Grey
Cable Clamp • Used to provide a secure cable fixing at the point of entry or
exit from furniture• Screws not provided
Code Length
650007 1000mm
650013 1500mm
650016 2000mm
Code Diameter
650033 20mm
650034 30mm
650035 40mm
Code Dimensions
630001 25mm (W) x 30mm (H)
Code Dimensions
630002 10mm (W) x 40mm (H)
Accessories
40mm 30mm 20mm
www.cmd-ltd.com 42
Design a power module to suit your needs
Socket options
*Note: We recommend that a dual supply is used when a 110V American socket is installed with a UK 240V supply.
Some modules are also available with Footprint, our energy management system, and our breakers/protection options so please ask a member of our sales team for more information.
Switches:• Neon Switch• Single Pole (with
or without neon)• Double Pole (with
or without neon)
UK Sockets:• Standard UK 45 & 90 degrees • Standard UK fused 45 & 90 degrees (3.15A & 5A)• T-earth 90 degrees• T-earth 90 degrees fused (3.15A & 5A)
International Sockets:• French/Belgian• German• Italian• Swiss• American*• Indian
Note: International sockets are only available in black and white but can be fitted with a black, grey or white surround.
www.cmd-ltd.com 44
Socket options
While standard configurations are offered, power modules can be adapted to meet your requirements. With a world of choice between sockets simply call us on +44 (0)1709 829511 to discuss your requirements.
Audio & Visual• HDMI• VGA• 3.5mm Audio• 3 Phono• Phono• S Video
Data Sockets:• RJ11• RJ45 (Cat5e, Cat6
and Cat6a)• LJ6C• USB• Data Slots
USB Charger:• 2 Amp USB Charger• 4 Amp USB Charger• Micro USB spool
All socket types are available in black, grey and white as standard.
Note: Slight colour variations may occur depending on socket type and batch number.
45sales line: +44 (0)1709 829511
Socket optionsOur twin port USB charger sockets are compatible with a range of in desk and on desk power modules. This dual port USB charger, available in 2A and 4A versions, is capable of charging a wide range of devices including the simultaneous charging of two Apple devices.
Our Micro USB spool can be fitted to our full range of on desk power modules, removing the need for separate mobile device chargers and cables.
• Available in black, grey and white to match our standard module colours.
• 500mm maximum cable length.
• Power is taken from adjacent dual port USB charging socket so no additional wiring is required.
• Can provide power for mini USB, Apple Lightning and Apple 30 pin connectors when used with our Micro USB adaptor.
• Available in black, grey and white to match our standard module colours.
• Complies with the latest charging standard (BS EN 62684 Interoperability specifications of common external power supply (EPS) for use with data-enabled mobile telephones)
• Powered from adjacent power socket so no additional wiring is required
Code Description
161404 Micro USB Adaptor
Note: These twin port USB charging devices are for charging only. No connection is made to a computer so data transfer is not available. USB cables are required but are not provided.
Our new data sockets can be fitted to our full range of on desk power modules and can be accessed from the back of the module to allow greater flexibility with date lead lengths.
• Available in black, grey and white to match our standard module colours
• New flat fronted design to improve overall aesthetic
• Rear access keystones to give greater flexibility for data lead lengths
• Supports our range of keystone couplers to include; RJ45, USB 2, USB C and HDMI
Code Description
161124 3m Cat 6 data cable. Male to male connector
161239 2m USB data cable. Male to male connector
161092 2m HDMI data cable. Male to male connector
Note: Separate data cables must be purchased with our new rear access data sockets. Other cable lengths are available on request.
www.cmd-ltd.com 46
AffinityConti
(Metal)Conti
(Plastic)Contour Eclipse Elite+ Harmony Horizon Inca Porthole Reveal
UK 13A ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓
French/Belgian 16A ✓ ✓ ✓ ✓ ✓ X ✓ ✓ X X ✓
German (Schuko) 16A ✓ ✓ ✓ ✓ ✓ X ✓ ✓ X X ✓
Indian 6A ✓ ✓ ✓ ✓ ✓ X ✓ ✓ X X ✓
Indian 16A ✓ ✓ X X X X ✓ ✓ X X ✓
Swiss 10A ✓ ✓ ✓ ✓ ✓ X ✓ ✓ X X ✓
USA 15A ✓ ✓ ✓ ✓ ✓ X ✓ ✓ X X ✓
Italian 10A/16A ✓ ✓ ✓ ✓ ✓ X ✓ ✓ X X ✓
Footprint ✓ ✓ ✓ ✓ X X ✓ ✓ X X ✓
Cat 5e ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ X X ✓
Cat 6 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ X ✓ ✓
Cat 6a ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ X ✓ ✓
Data Slots ✓ ✓ ✓ ✓ X X ✓ ✓ X X ✓
Micro USB/Data Spools ✓ ✓ X ✓ X X ✓ ✓ X X ✓
VGA ✓ ✓ ✓ ✓ ✓ X ✓ ✓ X X ✓
3.5mm Mini Jack Audio ✓ ✓ ✓ ✓ ✓ X ✓ ✓ X X ✓
HDMI ✓ ✓ ✓ ✓ ✓ X ✓ ✓ X ✓ ✓
USB Data ✓ ✓ ✓ ✓ ✓ X ✓ ✓ X ✓ ✓
USB Data Hub (x4) ✓ ✓ ✓ ✓ ✓ X ✓ ✓ X X ✓
USB Charger 2A ✓ ✓ ✓ ✓ ✓ X ✓ ✓ ✓ ✓ ✓
USB Charger 4A ✓ ✓ ✓ ✓ ✓ X ✓ ✓ X X ✓
Phono ✓ ✓ ✓ ✓ ✓ X ✓ ✓ X ✓ ✓
Breakers/Protection ✓ ✓ X ✓ X X ✓ ✓ X X ✓
Build it your way
Build it your way Manage your energy
The customise me logo shows that socket variations can be configured to suit your individual needs. See below.
The Footprint logo shows when a module can be configured for energy management. See page 175.
USB Sockets CMD supply two different types of USB sockets; USB data and USB charging. Our USB Data sockets come complete with a USB cable that must be connected to the corresponding USB socket on a computer to allow data to be transferred to and from the on desk module. Our USB charging socket is hardwired into the module’s power supply to produce a dual port USB charger capable of charging a wide range of devices including the simultaneous charging of two Apple devices.
Compatible modules are identified by the blue tick ✓Product Selection
Rating of commonly used appliances (Source: Electrical Safety Council www.esc.org.uk)
Appliances Amps Watts
Computer Monitor <0.5A 100W
Desktop Computer 3.0A 700W
Desk Lamp <0.5A 60W
Laptop Charger <0.5A 65-100W
Printer <0.5A 50W
Appliances Amps Watts
Mobile Phone Charger <0.5A <12W
Landline Cordless Phone Charger <0.5A 10W
Wi-Fi Router <0.5A 10W
Radio <0.5A 40W
Vacuum Cleaner 9.0A 2000W
USB Data USB Charging
Non-compatible modules are identified by the red cross X
47sales line: +44 (0)1709 829511
If you still want the modern, curved appearance of Contour without the restrictions in length, then our new metal Contour with its sleek silver anodised metal extrusion is the one for you.
Contour metal power and data
• Extruded silver metal body for longer lengths• Power and data cables all exit from the back of the
unit unless on a slatwall/tool rail where cables exit from the bottom of the unit
• Unit complies with BS 5733• All standard options are supplied with a 1m mains
lead to 3 pole connector and 3m data lead where relevant
• Requires a separate mains lead if connected directly to a socket
• Fixing via Contour C clamp or adhesive fixing kit• Segregation between power and data to comply
with BS 6396• No visible fixing screws
Note: CMD cannot accept any responsibility or liability for providing category 6 performance in products supplied.
Fuses: Only accessible after removal of equipment plug. Lead lengths shown will be the conductor length and not the distance from the end of the module to the plug. For example, a 3m prewired power lead will be approximately 2.875m as 125mm will be internal for the termination. This is also applicable for data leads. Data fascias may be subject to colour change.
Cables: White and grey modules are supplied with white cables and black modules are supplied with black cables.
HDMI: CMD cannot accept any responsibility or liability for providing HDMI performance in products supplied over 10m in length.
Please see page 47 for more information.
Build it your way
Configure to allow energy to be monitored and
controlled with Footprint. See page 155 for more details.
Manage your energy
Choose from power, USB charging, data, audio and
international sockets
Lateral fuses with a choice of 3.15A
or 5A to comply withBS 6396:2008
Anodised aluminium extruded body
81m
m
60mm
www.cmd-ltd.com 48
Contour metal power and data
Black Grey White
Adhesive Fixing Kit
Adhesive Kit, 1 Kit required per module
C clamp
We recommend using 2 x C clamps for any module with more than 2 sockets. Fits desk thickness between 20mm-32mm
Code
440006
Code
440371 35mm
14mm
35m
mCode Colour Description
94MCP02BGST Black Contour 1 x power, 1m mains lead to 3 pole connector, 1 x Twin port 2Amp USB Charger
94MCP02GGST Grey
94MCP02WGST White
94MPS01BGST Black Contour 2 x power, 1m mains lead to 3 pole connector
94MPS01GGST Grey
94MPS01WGST White
94MCP01BGST Black Contour 2 x power, 1m mains lead to 3 pole connector, 1 x Twin port 2Amp USB Charger
94MCP01GGST Grey
94MCP01WGST White
94MUS03BGST Black Contour 2 x power, 1m mains lead to 3 pole connector, 2 x RJ45 data Cat6, 3m data leads
94MUS03GGST Grey
94MUS03WGST White
94MPS02BGST Black Contour 4 x power, 1m mains lead to 3 pole connector
94MPS02GGST Grey
94MPS02WGST White
Code Description
161124 3m Cat 6 data cable. Male to male connector.
161239 2m USB data cable. Male to male connector.
161092 2m HDMI data cable. Male to male connector.
Note: Separate data cables must be purchased with our new rear access data sockets. Other cable lengths are available on request.
49sales line: +44 (0)1709 829511
Please see page 47 for more information.
Contour has a modern, curved appearance displaying many design features like our lateral fuse carrier, internal segregation between power and data and comes complete with plastic clips on the covers so there are no visible fixing screws and fully compliant to current safety regulations.
Contour power and data
• Power and data cables all exit from the back of the unit unless on a slatwall/tool rail where cables exit from the bottom of the unit
• Unit complies with BS 5733• All standard options are supplied with a 1m mains
lead to 3 pole connector and 3m data lead where relevant
• Requires a separate mains lead if connected directly to a socket
• Fixing via Contour C clamp or adhesive fixing kit
Build it your way
Configure to allow energy to be monitored and
controlled with Footprint. See page 155 for more details.
*Please note that 6 tiles is the maximum with a maximum
length of 362.5mm.
Manage your energy
Note: CMD cannot accept any responsibility or liability for providing category 6 performance in products supplied.
Fuses: Only accessible after removal of equipment plug. Lead lengths shown will be the conductor length and not the distance from the end of the module to the plug. For example, a 3m prewired power lead will be approximately 2.875m as 125mm will be internal for the termination.This is also applicable for data leads. Data fascias may be subject to colour change.
Cables: White and grey modules are supplied with white cables and black modules are supplied with black cables.
HDMI: CMD cannot accept any responsibility or liability for providing HDMI performance in products supplied over 10m in length.
Choose from power, USB charging, data, audio and
international sockets
Lateral fuses with a choice of 3.15A
or 5A to comply withBS 6396:2008 Flame retardant ABS
plastic body with a choice of fascia colours
81m
m
60mm
www.cmd-ltd.com 50
Code Colour Description
94CP01GST Black/White Contour 1 x power, 1m mains lead to 3 pole connector, 1 x Twin port 2Amp USB Charger
94CP02GST Grey/White
94CP03GST All White
94CP04GST All Black
94PS04GST Black/White Contour 2 x power, 1m mains lead to 3 pole connector
94PS01GST Grey/White
94PS07GST All White
94PS10GST All Black
94CP05GST Black/White Contour 2 x power, 1m mains lead to 3 pole connector, 1 x Twin port 2Amp USB Charger
94CP06GST Grey/White
94CP07GST All White
94CP08GST All Black
94U048GST Black/White Contour 2 x power, 1m mains lead to 3 pole connector, 2 x RJ45 data Cat6
94U049GST Grey/White
94U050GST All White
94U051GST All Black
94PS06GST Black/White Contour 4 x power, 1m mains lead to 3 pole connector
94PS03GST Grey/White
94PS09GST All White
94PS11GST All Black
Black Grey All White All Black
Adhesive Fixing Kit
Adhesive Kit, 1 Kit required per module
C clamp
We recommend using 2 xC clamps for any module with more than 2 sockets. Fits desk thickness between 20mm-32mm
Contour power and data
Code
440006
Code
440371 35mm
14mm
35m
m
Code Description
161124 3m Cat 6 data cable. Male to male connector.
161239 2m USB data cable. Male to male connector.
161092 2m HDMI data cable. Male to male connector.
Note: Separate data cables must be purchased with our new rear access data sockets. Other cable lengths are available on request.
51sales line: +44 (0)1709 829511
New Harmony power and dataHarmony is a versatile desk power solution, specifically designed to meet the increasing power and everyday communication needs of a working office. The Harmony features integral fuses which are fully compliant to current safety regulations and is configured with segregated power & data choices to suit different workstation requirements. Harmony can be used in conjunction with our under desk modules to provide greater power solutions and is fitted to the edge of desk with C clamps or adhesive kit making it functional yet non-intrusive to the working desk.
Choose from power, USB charging, data, audio and
international socketsLateral fuses with a choice of 3.15A
or 5A to comply withBS 6396:2008
Anodised aluminium extruded body
• Anodised aluminium extruded body available in silver or painted black
• Choice of Black, Grey or White fascias/end caps• Fully segregated power and data• All UK sockets feature integral fuses. Choice of
3.15A or 5A fuses are available to comply with BS 6396
• All standard options are supplied with a 1m mains lead to male 3 pole connector. Requires a separate mains lead if passing from a 13A socket
• Data leads are supplied at a standard length of 3 metres
• Tested to comply BS 5733• Fixing via standard C clamps or adhesive fixing kit
Note: CMD cannot accept any responsibility or liability for providing category 6 performance in products supplied.
Fuses: Only accessible after removal of equipment plug. Lead lengths shown will be the conductor length and not the distance from the end of the module to the plug. For example, a 3m prewired power lead will be approximately 2.875m as 125mm will be internal for the termination. This is also applicable for data leads. Data fascias may be subject to colour change.
Cables: White and grey modules are supplied with white cables and black modules are supplied with black cables.
HDMI: CMD cannot accept any responsibility or liability for providing HDMI performance in products supplied over 10m in length.
Please see page 47 for more information.
Build it your way
Configure to allow energy to be monitored and
controlled with Footprint. See page 155 for more details.
Manage your energy
80m
m
80mm
Matching inner end cap as standard but coloured options available subject
to MOQ
Newly designed outer end cap with no
visible screwsNewProduct
www.cmd-ltd.com 52
New Harmony power and data
Black/Silver Grey/Silver White/Silver
50mm
35mm
35m
m
C clamp
We recommend using 2 x C clamps for any module with more than 2 sockets. Fits desk thickness of 20-32mm
Code
440005
Adhesive Fixing Kit
Adhesive Kit, 1 Kit required per module
Code
440006
Code Colour Description
8400001 Black/Silver Harmony 1 x power, 1m mains lead to 3 pole connector, 1 x Twin port 2Amp USB Charger
8400002 Grey/Silver
8400003 White/Silver
8400005 Black/Silver Harmony 2 x power, 1m mains lead to 3 pole connector
8400006 Grey/Silver
8400007 White/Silver
8400009 Black/Silver Harmony 2 x power, 1m mains lead to 3 pole connector, 1 x Twin port 2Amp USB Charger
8400010 Grey/Silver
8400011 White/Silver
8400013 Black/Silver Harmony 2 x power, 1m mains lead to 3 pole connector, 2 x RJ45 data Cat6
8400014 Grey/Silver
8400015 White/Silver
8400017 Black/Silver Harmony 4 x power, 1m mains lead to 3 pole connector
8400018 Grey/Silver
8400019 White/Silver
The newly designed double end cap system presents a number of options for contrasting inner end caps whether this be using our standard colours, our new orange, cyan and lime or choosing *bespoke colours to compliment your brand. *Bespoke colours are subject to minimum order quantities and lead times.
Code Description
161124 3m Cat 6 data cable. Male to male connector.
161239 2m USB data cable. Male to male connector.
161092 2m HDMI data cable. Male to male connector.
Note: Separate data cables must be purchased with our new rear access data sockets. Other cable lengths are available on request.
Orange Cyan Lime
53sales line: +44 (0)1709 829511
• Choice of Black, Grey or White body and matching socket fascias. Other colour combinations available subject to MOQ and lead times
• Inca has 4 usable faces offering a wide range of configurations for power and USB charging
• All UK sockets feature integral fuses with a choice of 3.15A or 5A fuses to comply with BS 6396
• All standard options are supplied with a 1m mains lead to male 3 pole connector.
• Inca is available as a freestanding on desk module or can be fixed using a simple grommet hole fixing
• The modules is made of flame retardant ABS plastic body and is tested to comply BS 5733
Inca power and USB chargingInca is a new module designed specifically for communal areas and meeting rooms. This stylish power and USB charging module is available in black, grey and white and has four faces that can be configured in a variety of ways to meet the power needs of any working environment.
Fuses: Only accessible after removal of equipment plug. Lead lengths shown will be the conductor length and not the distance from the end of the module to the plug. For example, a 3m prewired power lead will be approximately 2.875m as 125mm will be internal for the termination.
Cables: White and grey modules are supplied with white cables and black modules are supplied with black cables.
Please see page 47 for more information.
Build it your way
Twin port 2A USB charging sockets
Independently certified to comply with BS 5733
Available in black, grey and white (other colours combinations available
subject to MOQ)
Individual fusedpower socket
(3.15A or 5A options)
Flame retardant ABSplastic body
NewProduct
70mm
65m
m
7mm
Standard Tile50mm x 50mm
57m
m70
mm
140m
m
Ø103.5mm
www.cmd-ltd.com 54
Black Grey White
Inca power and USB charging
Code Colour Description
7900004 Black Inca 2 Power, 1m mains lead to 3 pole connector. On Desk.
7900005 Grey
7900006 White
7900010 Black Inca 4 Power, 1m mains lead to 3 pole connector. On Desk.
7900011 Grey
7900012 White
7900013 Black Inca 1 Power, 1 Twin port 2Amp USB Charger, 1m mains lead to 3 pole connector. On Desk.
7900014 Grey
7900015 White
7900016 Black Inca 2 Power, 1 Twin port 2Amp USB Charger, 1m mains lead to 3 pole connector. On Desk.
7900017 Grey
7900018 White
7900019 Black Inca 3 Power, 1 Twin port 2Amp USB Charger, 1m mains lead to 3 pole connector. On Desk.
7900020 Grey
7900021 White
7900025 Black Inca 2 Power, 2 Twin port 2Amp USB Charger, 1m mains lead to 3 pole connector. On Desk.
7900026 Grey
7900027 White
Code Colour Description
7900034 Black Inca 2 Power, 1m mains lead to 3 pole connector. Grommet hole fixing.7900035 Grey
7900036 White
7900040 Black Inca 4 Power, 1m mains lead to 3 pole connector. Grommet hole fixing.7900041 Grey
7900042 White
7900043 Black Inca 1 Power, 1 Twin port 2Amp USB Charger, 1m mains lead to 3 pole connector. Grommet hole fixing.
7900044 Grey
7900045 White
7900046 Black Inca 2 Power, 1 Twin port 2Amp USB Charger, 1m mains lead to 3 pole connector. Grommet hole fixing.
7900047 Grey
7900048 White
7900049 Black Inca 3 Power, 1 Twin port 2Amp USB Charger, 1m mains lead to 3 pole connector. Grommet hole fixing.
7900050 Grey
7900051 White
7900055 Black Inca 2 Power, 2 Twin port 2Amp USB Charger, 1m mains lead to 3 pole connector. Grommet hole fixing.
7900056 Grey
7900057 White
On Desk Module
This module sites diectly on the desk surface so no fixings are required.
Grommet Mount Module
This module is fixed to the desk using an 80mm grommet hole fixing and is secured using a simple screw fit mechanism.
Product Guide: P = UK Power Socket C = Twin port 2A USB Charging Socket
The Inca module has a cable entry point at the back (not used with grommet mount module). This can be used to define the front, back, left and right of the module.
All Inca modules come with a power socket on the left as standard.
Inca is available in a number of configurations. Shown here with 2x Power and 2x Twin port 2A USB Charging.
P P P
C
CBack
Front
Left
Righ
t
55sales line: +44 (0)1709 829511
Individual fusedpower socket
(3.15A or 5A options)
Independently certified to comply with BS 5733
• Available with a choice of black, white and grey plastic fascia surrounded by a metallic finished trim
• Compact dimensions, ideal for space-saving installations
• Features individual fuse & independently certified to BS 5733
• Fully segregated power and data• Easy to retrofit, incorporates an under desk, hand
tightened barrel nut to fix unit in place• Power and data cables all exit from the base of
the unit & come with a standard 1m mains lead to 3 pole connector, 3m data lead and 2m USB lead where appropriate
• Designed to fit any desk thickness between 13mm and 50mm
With its innovative design, PortHole is ideal for adapting an existing 80mm cable hole to allow a single power socket and a choice of keystones to be fitted to a desk with a simple screw fit mechanism.
PortHole power and data
Available in black, white or grey with metallic
finished trim
The lip ensures that spillages cannot enter
the module
Other keystones available (USB, HDMI,
Data, Mini Jack)
Note: CMD cannot accept any responsibility or liability for providing category 6 performance in products supplied.
Fuses: Only accessible after removal of equipment plug. Lead lengths shown will be the conductor length and not the distance from the end of the module to the plug. For example, a 3m prewired power lead will be approximately 2.875m as 125mm will be internal for the termination. This is also applicable for data leads. Data fascias may be subject to colour change.
Cables: White and grey modules are supplied with white cables and black modules are supplied with black cables.
HDMI: CMD cannot accept any responsibility or liability for providing HDMI performance in products supplied over 10m in length.
Please see page 47 for more information.
Build it your way
Ø95mm
60m
m
7mm
73m
m
Ø103.5mm
www.cmd-ltd.com 56
Code Colour Description
90P001BGST Black 1 x Power Socket
Power socket 3.15A individually fused with 1m mains cable
to 3 Pole connector90P001GGST Grey
90P001WGST White
90U001BGST Black 1 x Power Socket, 1 x RJ45 Cat6 Socket
Power socket 3.15A individually fused with 1m mains cable to 3 Pole connector and 3m data lead
90U001GGST Grey
90U001WGST White
90U002BGST Black 1 x Power Socket, 2 x RJ45 Cat6 Sockets
Power socket 3.15A individually fused with 1m mains cable to 3 Pole connector and 2 x 3m data leads
90U002GGST Grey
90U002WGST White
90U003BGST Black 1 x Power Socket, 1 x USB Socket (Data transfer)
Power socket 3.15A individually fused with 1m mains cable to 3 Pole connector and 2m USB lead
90U003GGST Grey
90U003WGST White
90U004BGST Black 1 x Power Socket, 2 x USB Sockets (Data transfer)
Power socket 3.15A individually fused with 1m mains cable to 3 Pole connector and 2 x 2m USB leads
90U004GGST Grey
90U004WGST White
90U005BGST Black 1 x Power Socket, 1 x RJ45 Cat6 Socket, 1 x USB Socket (Data transfer)
Power socket 3.15A individually fused with 1m mains cable to 3 Pole connector, 3m data lead and 2m USB lead
90U005GGST Grey
90U005WGST White
PortHole power and data
HDMI sockets, Mini Jack Keystones and 5A fuses are also available. Cat6 socket is fully backward compatible.
Black
White
Grey
Tool free ‘screw fit’103.5mm diameter lock
to nut
Available in black, white or grey with metallic
finished trim
57sales line: +44 (0)1709 829511
Note: CMD cannot accept any responsibility or liability for providing category 6 performance in products supplied. We will however fit category 6 specification components where specified.
Fuses only accessible after removal of equipment plug. Lead lengths shown will be the conductor length and not the distance from the end of the module to the plug. For example, a 3m prewired power lead will be approximately 2.875m as 125mm will be internal for the termination. This is also applicable for data leads.
HDMI: CMD cannot accept any responsibility or liability for providing HDMI performance in products supplied over 10m in length.
This version of PortHole has been designed to include our dual port USB charger, which is capable of charging a wide range of devices including the simultaneous charging of two Apple devices.
PortHole II power and USB charging
• Complies with the latest charging standard (BS EN 62684 Interoperability specifications of common external power supply (EPS) for use with data-enabled mobile telephones)
• Dual port USB charger capable of charging a wide range of devices including the simultaneous charging of two Apple devices
• Two independent USB charging ports, which can be used at the same time• Powered from adjacent power socket so no additional wiring is required• The charger is compatible with our full range of in desk and on desk modules
Code Colour Description
90CP01BGST Black 1 x Power Socket Power socket 3.15A individually fused with 2 port USB charger, 1m mains cable to 3 Pole connector
90CP01GGST Grey
90CP01WGST White
Individual fusedpower socket
(3.15A or 5A options)
Independently certified to comply with BS 5733
Available in black, white or grey with metallic
finished trim
The lip ensures that spillages cannot enter
the module
2x USB charging sockets
www.cmd-ltd.com 58
PortHole III wireless charging
Code Colour Description
90WP01BGST Black 1 x Wireless charging module 1m mains cable to 3 Pole connector90WP01GGST Grey
90WP01WGST White
90WR01W White 1x Wave wireless receiver 1x micro USB and 1x Apple Lightning connector
Wireless charging surface
The lip ensures that spillages cannot enter
the module
IntegralPowerSupply
This award winning version of PortHole takes charging to the next level - wireless! It is ideal for adapting an 80mm cable hole or for upgrading your existing PortHole and PortHole II modules.
Simply place your wireless induction charging compatible device on the charger. A beep will acknowledge the connection, LED’s will illuminate around the charger’s perimeter and charging will commence.
What makes PortHole III unique is that CMD have developed a wireless charger that has an integral power supply so there is no requirement for a separate device to power the module.
Wireless charging surface
Micro USBConnector
iPhone5/5C/5SConnector
For illustration purposes only. Please note: This product will not charge two devices at the same time.
WaveWireless charging receiver
This new wireless charging receiver has been designed to work with our the PortHole III wireless charging module.
Simply insert the connector into the device’s micro USB or Apple Lightning socket and place the wireless charging receiver in the centre of the PortHole III wireless charging module.
59sales line: +44 (0)1709 829511
Reveal power and dataThe new Reveal through desk module is our premium product of this type and is the perfect solution for providing power and data sockets in boardroom and office environments. The unit is available in a selection of finishes and features a soft closing lid mechanism to create a quality finish. The dual action lid mechanism also creates a generous shadow gap for cable exit whilst offering a seamless appearance when not in use.
• Comes in black, grey and white painted finish• Available in two sizes; small is 348mm x 155mm
(cut our size 333mm x 140mm) and large is 448mm x 155mm (cut out size 433mm x 140mm)
• Seamless low profile surround• Smooth action lid that retracts to allow access
from both sides• Fitting from above and locked into position
using under desk fixings• All UK power socket versions feature individual
fuses• Choice of 3.15A or 5A fuses are available to
comply with BS 6396• Unit complies with BS 5733• All standard options are supplied with a 3m
mains lead to 13A UK plug and 3m data leads
Fully closed position
Partially closed position
NewProduct
Choose from power, data, audio, USB, and international sockets
Painted metal body with seamless
low profile surround
Lateral fuses with a choice of 3.15A or 5A to comply with BS 6396
Soft closeretractable lid
www.cmd-ltd.com 60
Code Colour Description
7800101 BlackReveal 2x Power, 3m mains lead to 13A UK plug, 1x Twin port 2Amp USB Charger, 1x HDMIProduct cutout dimensions: 140mm x 333mm*
7800102 WhiteReveal 2x Power, 3m mains lead to 13A UK plug, 1x Twin port 2Amp USB Charger, 1x HDMIProduct cutout dimensions: 140mm x 333mm*
7800103 GreyReveal 2x Power, 3m mains lead to 13A UK plug, 1x Twin port 2Amp USB Charger, 1x HDMIProduct cutout dimensions: 140mm x 333mm*
7800104 BlackReveal 2x Power, 3m mains lead to 13A UK plug, 1x Twin port 2Amp USB Charger, 1x Charging Spool, 2x Data, 1x HDMI, 1x VGA and 1x Mini JackProduct cutout dimensions: 140mm x 433mm*
7800105 WhiteReveal 2x Power, 3m mains lead to 13A UK plug, 1x Twin port 2Amp USB Charger, 1x Charging Spool, 2x Data, 1x HDMI, 1x VGA and 1x Mini JackProduct cutout dimensions: 140mm x 433mm*
7800106 GreyReveal 2x Power, 3m mains lead to 13A UK plug, 1x Twin port 2Amp USB Charger, 1x Charging Spool, 2x Data, 1x HDMI, 1x VGA and 1x Mini JackProduct cutout dimensions: 140mm x 433mm*
Reveal power and data
Note: CMD cannot accept any responsibility or liability for providing category 6 performance in products supplied. *Dimensions are meant as a guide and have a +/-1mm tolerance.
Fuses: Only accessible after removal of equipment plug. Lead lengths shown will be the conductor length and not the distance from the end of the module to the plug. For example, a 3m prewired power lead will be approximately 2.875m as 125mm will be internal for the termination, this is also applicable for data leads. Data fascias may be subject to colour change.
Cables: White and grey modules are supplied with white cables and black modules are supplied with black cables.
HDMI: CMD cannot accept any responsibility or liability for providing HDMI performance in products supplied over 10m in length.
Please see page 47 for more information.
Build it your way
Configure to allow energy to be monitored and
controlled with Footprint. See page 155 for more details.
Manage your energy
70.6
mm
150.0mm
35.0
mm
133.0mm
Black Grey White
61sales line: +44 (0)1709 829511
Horizon power and dataThe Horizon through desk module offers accessible power and data sockets at the desk top. This unit fits flush into the desktop with an angular and smooth aesthetic finish. Spring release buttons lock unit above desk surface. These are then pushed together to allow the unit to retract into housing below desk surface. The Horizon’s lid retracts to allow access from both sides, when opened it lifts and locks proud of the desk surface which makes it ideal for use in boardrooms or conference tables. Horizon is finished in Fusion Silver.
Choose from power, data, audio, USB, and international sockets
Lateral fuses with a choice of 3.15A or 5A to comply
with BS 6396
Spring loadedrelease button
Retractable lid
Nylon brushcable entry
• Fusion silver finish with flame retardant ABS Grey (RAL7004) socket fascias
• Module lifts and locks proud of the desk surface• Lid retracts to allow access from both sides –
suitable for conference tables• Fitting from above, locks into position using two
screws• Spring loaded buttons lock module proud of
desk surface and on release allows module to retract below desk surface
• Available with power and data configurations to suit individual client needs
• All UK power socket versions feature individual fuses
• Choice of 3.15A or 5A fuses are available to comply with BS 6396
• Unit complies with BS 5733• All standard options are supplied with a 3m mains
lead to 13A UK plug and 3m data leads where relevant
Closed Position
www.cmd-ltd.com 62
Code Description
96P044Horizon 2 x power, 3m mains lead to 13A UK plugProduct cutout dimensions: 134mm x 205mm*
96P045Horizon 4 x power, 3m mains lead to 13A UK plugProduct cutout dimensions: 134mm x 330mm*
96U122Horizon 2 x power, 3m mains lead to 13A UK plug, 2 x RJ45 data Cat6, 3m data leadsProduct cutout dimensions: 134mm x 267mm*
96U123Horizon 4 x power, 3m mains lead to 13A UK plug, 2 x RJ45 data Cat6, 3m data leadsProduct cutout dimensions: 134mm x 391mm*
96H066Horizon 2 x power, 3m mains lead to 13A UK plug, 2 x RJ45 data Cat6, 1 x VGA, 1 x mini jack, 3m data & A/V leadsProduct cutout dimensions: 134mm x 330mm*
96H067Horizon 2 x power, 3m mains lead to 13A UK plug, 2 x RJ45 data Cat6, 1 x VGA, 1 x mini jack, 1 X HDMI, 3m data & A/V leadsProduct cutout dimensions: 134mm x 391mm*
96CP02Horizon 2 x power, 3m mains lead to 13A plug, 1x Twin port 2Amp USB Charger, Product cutout dimensions: 134mm x 267mm*
96CP09Horizon 2 x power, 3m mains lead to 13A UK plug, 1x Twin port 2Amp USB Charger, 2 x RJ45 data Cat6, 3m data leadsProduct cutout dimensions: 134mm x 330mm*
Horizon power and data
Note: CMD cannot accept any responsibility or liability for providing category 6 performance in products supplied. *Dimensions are meant as a guide and have a +/-1mm tolerance.
Fuses: Only accessible after removal of equipment plug. Lead lengths shown will be the conductor length and not the distance from the end of the module to the plug. For example, a 3m prewired power lead will be approximately 2.875m as 125mm will be internal for the termination, this is also applicable for data leads. Data fascias may be subject to colour change.
Cables: White and grey modules are supplied with white cables and black modules are supplied with black cables.
HDMI: CMD cannot accept any responsibility or liability for providing HDMI performance in products supplied over 10m in length.
Please see page 47 for more information.
Build it your way
Configure to allow energy to be monitored and
controlled with Footprint. See page 155 for more details.
Manage your energy 93m
m
149mm
132mm
20m
m
63sales line: +44 (0)1709 829511
Closed Position
Affinity power and data
Choose from power, data, audio, USB, and international sockets
Lateral fuses with a choice of 3.15A or 5A to comply
with BS 6396:2008
Affinity module offers the convenience of power and data at the desktop when you need it and an uncluttered work surface when you don’t. It is a concealed unit that can function in the open or closed position.
• Unit has grey fascia end caps and an anodised aluminium body. Fascia is Vø flame retardant ABS with grey socket fascias
• Clamps into rectangular location hole using ratchet clamps
• Power and data cables all exit from under the side of the unit
• All UK power socket versions feature individual fuses
• Choice of 3.15A or 5A fuses are available to comply with BS 6396
• Unit complies with BS 5733• All standard options are supplied with a 3m
mains lead to 13A UK plug and 3m data leads where relevant
Anodised aluminium extended body
www.cmd-ltd.com 64
Affinity power and data
Note: CMD cannot accept any responsibility or liability for providing category 6 performance in products supplied. *Dimensions are meant as a guide and have a +/-1mm tolerance.
Fuses: Only accessible after removal of equipment plug. Lead lengths shown will be the conductor length and not the distance from the end of the module to the plug. For example, a 3m prewired power lead will be approximately 2.875m as 125mm will be internal for the termination. This is also applicable for data leads. Data fascias may be subject to colour change.
Cables: White and grey modules are supplied with white cables and black modules are supplied with black cables.
HDMI: CMD cannot accept any responsibility or liability for providing HDMI performance in products supplied over 10m in length.
Code Description
85PG01Affinity 2 x power, 3m mains lead to 13A UK plugProduct cutout dimensions: 132mm x 161.5mm*
85PG03Affinity 4 x power, 3m mains lead to 13A UK plugProduct cutout dimensions: 132mm x 286.5mm*
85U490Affinity 2 x power, 3m mains lead to 13A UK plug, 2 x RJ45 data Cat6, 3m data leadsProduct cutout dimensions: 132mm x 286.5mm*
85U493Affinity 4 x power, 3m mains lead to 13A UK plug, 2 x RJ45 data Cat6, 3m data leadsProduct cutout dimensions: 132mm x 361.5mm*
85HG02Affinity 2 x power, 3m mains lead to 13A UK plug, 2 x RJ45 data Cat6, 1 x VGA, 1 x mini jack, 3m data & A/V leadsProduct cutout dimensions: 132mm x 299mm*
85AV52050Affinity 2 x power, 3m mains lead to 13A UK plug, 2 x RJ45 data Cat6, 1 x VGA, 1 x mini jack, 1 x HDMI, 3m data & A/V leadsProduct cutout dimensions: 132mm x 324mm*
85CP02Affinity 2 x power, 3 mains lead to 13A plug, 1x Twin port 2Amp USB ChargerProduct cutout dimensions: 132mm x 224mm*
85CP10Affinity 2 x power, 3 mains lead to 13A UK plug, 1x Twin port 2Amp USB Charger, 2 x RJ45 data Cat6, 3m data leadsProduct cutout dimensions: 132mm x 286.5mm*
Please see page 47 for more information.
Build it your way
Configure to allow energy to be monitored and
controlled with Footprint. See page 155 for more details.
Manage your energy
93m
m
145mm
131mm
12mm73
mm
65sales line: +44 (0)1709 829511
• Standard finish is anodised silver body with grey (RAL7004) socket fascias
• Easy to fit to new furniture or to retrofit using a 115mm hole saw
• Incorporates an under desk, hand tightened barrel nut to fix unit into place
• Fully segregated power and data• Choice of power and data connectors to
most specifications
Eclipse power and dataA through desk power and data module that pulls up from the work surface and pushes back down to a flush position when not in use.
Lateral fuses with a choice of 3.15A or 5A to comply
with BS 6396
Configurablemodifications
• Power and data cables all exit from the base of the unit
• Standard lead length is 3m mains to 13A plug
• All UK power sockets feature integral fuses• Choice of 3.15A or 5A fuses are available to
comply with BS 6396• Complies with BS 5733
Power or data sockets available
Closed Position
www.cmd-ltd.com 66
Eclipse power and data
Note: Please note that Cat 6 is backwards compatible. CMD cannot accept any responsibility or liability for providing category 6 performance in products supplied. We will however fit category 6 specification components where specified. *Dimensions are meant as a guide and have a +/- 1mm tolerance.
Fuses only accessible after removal of equipment plug. Lead lengths shown will be the conductor length and not the distance from the end of the module to the plug. For example, a 3m prewired power lead will be approximately 2.875m as 125mm will be internal for the termination. This is also applicable for data leads. Data fascias may be subject to colour change.
HDMI: CMD cannot accept any responsibility or liability for providing HDMI performance in products supplied over 10m in length.
Code Description
83P066 Eclipse 2 x power, 3m mains lead to 13A UK plug
83P067 Eclipse 4 x power, 3m mains lead to 13A UK plug
83U235 Eclipse 2 x power, 3m mains lead to 13A UK plug, 2 x RJ45 data Cat6, 3m data leads
83U236 Eclipse 4 x power, 3m mains lead to 13A UK plug, 2 x RJ45 data Cat6, 3m data leads
83H099Eclipse 2 x power, 3m mains lead to 13A UK plug, 2 x RJ45 data Cat6, 1 x VGA, 1 x mini jack, 3m data & A/V leads
83CP02 Eclipse 2 x power, 3 mains lead to 13A UK plug, 1x Twin port 2Amp USB Charger
83AV71674 Eclipse 2 x power, 3 mains lead to 13A UK plug, 2 x RJ45 data Cat6, 1 x VGA, 1 x mini jack, 1 x HDMI, 3m data leads
83CP10 Eclipse 2 x power, 3 mains lead to 13A UK plug, 1x Twin port 2Amp USB Charger, 2 x RJ45 data Cat6, 3m data leads
520167 Eclipse 115mm cable outlet
Please see page 47 for more information.
Build it your way
Configure to allow energy to be monitored and
controlled with Footprint. See page 155 for more details.
Manage your energy
Ø130mm
72m
m
Dep
th w
ill v
ary
depe
ndin
g on
con
figur
atio
n
1.95mm
Ø115mm Cutout
Ø180mm
67sales line: +44 (0)1709 829511
All products have 300mm earth lead to M5 ring Socket Orientation: N – is North, E – is East & W – is West
Code Description
92K005GST 2x power sockets individually fused 3.15A with male 3 Pole Connector input & female 3 Pole Connector output. EW
92K011GST 2x power sockets individually fused 5A with male 3 Pole Connector input & female 3 Pole Connector output. EW
92K006GST 2x power sockets with neon switches individually fused 3.15A with male 3 Pole Connector input & female 3 Pole Connector output. EW
92K012GST 2x power sockets with neon switches individually fused 5A with male 3 Pole Connector input & female 3 Pole Connector output. EW
92K007GST 3x power sockets individually fused 3.15A with male 3 Pole Connector input & female 3 Pole Connector output. ENW
92K013GST 3x power sockets individually fused 5A with male 3 Pole Connector input & female 3 Pole Connector output. ENW
92K002GST 4x power sockets individually fused 3.15A with male 3 Pole Connector input & female 3 Pole Connector output. ENNW
92K008GST 4x power sockets individually fused 5A with male 3 Pole Connector input & female 3 Pole Connector output. ENNW
92K004GST 4x power sockets individually fused 3.15A with male 3 Pole Connector input & female 3 Pole Connector output. NNNN
92K010GST 4x power sockets individually fused 5A with male 3 Pole Connector input & female 3 Pole Connector output. NNNN
92K003GST 4x power sockets one neon switch, individually fused 3.15A with male 3 Pole Connector input & female 3 Pole Connector output. NNNN
92K009GST 4x power sockets one neon switch, individually fused 5A with male 3 Pole Connector input & female 3 Pole Connector output. NNNN
92K001GST 6x power sockets one neon switch, individually fused 3.15A with male 3 Pole Connector input. *No output. NNNNNW
Lateral fuses with a choice of 3.15A or 5A to comply
with BS 6396
Neon switch
Elite+ power
Elite+ is a moulded plastic power module, great when affordability is top priority.
• Requires a separate GST lead
• Product independently tested to BS5733
Fixing Lugs
Please note: Fuses only accessible after removal of equipment plug. *Complies with BS6396.
90o rotated socket for transformer plugs
www.cmd-ltd.com 68
Code Description
92KD01GST2x Power sockets one neon switch and 2x Data Compartment (Empty)
92KD02GST2x Power sockets one neon switch and 2x RJ45 Cat6 data sockets with 3m data leads
92KD03GST2x Power sockets one neon switch and 2x RJ45 Cat6 data sockets with 5m data leads
92KD04GST2x Power sockets one neon switch and 2x RJ45 Cat6 data sockets with 7m data leads
92KD05GST4x Power sockets one neon switch and 4x Data Compartment (Empty)
92KD06GST4x Power sockets one neon switch and 2x RJ45 Cat6 data sockets with 3m data leads 2x Data Compartment (Empty)
92KD07GST4x Power sockets one neon switch and 2x RJ45 Cat6 data sockets with 5m data leads 2x Data Compartment (Empty)
92KD08GST4x Power sockets one neon switch and 2x RJ45 Cat6 data sockets with 7m data leads 2x Data Compartment (Empty)
92K014Separate Data Module x 4 compartment - Empty Shell
92K018 2x RJ45 CAT6 data sockets with 3m data leads
92K020 4x RJ45 CAT6 data sockets with 3m data leads
Elite+ power and dataThese combined power and data modules have been designed to enable customers to configure their own data needs without the associated risks of exposure to an opened power module.
Note: Certain configurations can accommodate Cat6a Data sockets (contact us for further information)
Please note that CAT6 is backwards compatible. CMD cannot accept any responsibility or liability for providing CAT6 performance in products supplied. We will however fit CAT6 specification components where specified.
Up to 4 data sockets
Fixing lugs
4x UK socketsNeon switch
Earth lead
Fixing lugs
Up to 4 data sockets
Code Black Code White Length
601120GST 601220GST 2m
601130GST 601230GST 3m
601150GST 601250GST 5m
Starter Cable 13A UK Plug to Female 3 Pole Connector
Other lead lengths are available. Please see page 84 for full details.
69sales line: +44 (0)1709 829511
Sockets• Std UK 45° & 90°• Std UK fused 45° & 90° (3.15A
& 5A) • T-earth 90°• T-earth 90° fused (3.15A & 5A)• Round-earth 90°• Round earth fused 45° & 90° • 3.15A & 5A• French / Belgian• Swiss • American • Danish • Indian • IEC C13 & C19• German• Italian
Conti power and dataConti is a completely configurable desk power system, designed specifically to meet the increasing power and communication needs of the modern office. Modules have been designed with speed of installation and flexibility in mind. Its many unique design features enable a vast choice of power and data options to fulfil most specifications. A choice of either metal or plastic extrusion is available.
Configure to allow energy to be monitored and
controlled with Footprint. See page 155 for more details.
Manage your energy
In-feeds• Tap Offs• Hard Wired to mains cable (3 & 4
pole) in 1.5mm2, 2.5mm2 & 4.0mm2 • SY cable 1.5mm2 & 2.5mm2 • 16mm & 20mm Flexible conduit (i.e.
tap off) • Connector block 16A & 32A (for
self wiring) • 3 Pole Connector Panel mount (3 &
4 pole) • Neutrik Panel mount (20A & 32A)• GST connectors
Data• RJ11 • RJ45 (Cat5e, Cat6 and Cat6a) • LJ6C (telecom)
Protection • Std 13A mains fuse (10A & 13A) • MCB (various std ratings) - Grey,
White & Black shrouds available• RCD/RCBO (various std ratings) • Surge Filter • Mains conditioning filter • RFI filter
Other• USB • 3.5mm Audio • Phono Socket • SVGA • S Video • HDMI • Co Axial • 9 Pin ‘D Type’ • F Type Connector• BT Tel• RJ11 Tel Shuttered• RJ45 Cat5e, Cat6 and Cat6a• Ethernet BNC• Footprint (Page 103)
Switching• Neon indicator • Single pole (with or without neon) • Double pole (with or without neon)
Conduit• Metal
Construction• Plastic (89 Series)• Metal (86 Series)
Out-feeds• 3 & 4 Pole Connector
Please see page 47 for more information.
Build it your way
www.cmd-ltd.com 70
Note: We only supply mains fuse holders in black and white. If you require your Conti unit to be colour matched in grey our MCB is available in grey and white and is a good alternative to our fuse holder – please ask for details. HDMI: CMD cannot accept any responsibility or liability for providing HDMI performance in products supplied over 10m in length.
Conti power and data
Code Description
Standard Earth
86KS01 Standard 5m 32A Unfused Tap Off BSX3325H, 13A Fuse, 4 UK sockets, end cap
86KS03 Standard 5m 32A Unfused Tap Off BSX3325H, 13A Fuse, switch, 4 UK sockets, end cap
86KS02 Standard 5m 32A Unfused Tap Off BSX3325H, 13A Fuse, 6 UK sockets, end cap
86KS04 Standard 5m 32A Unfused Tap Off BSX3325H, 13A Fuse, switch, 6 UK sockets, end cap
86KS05 Standard 5m 32A Unfused Tap Off BSX3325H, 16A 30m RCBO, 4 UK sockets, end cap
86KS06 Standard 5m 32A Unfused Tap Off BSX3325H, 16A 30m RCBO, 6 UK sockets, end cap
Clean Earth
86KC01 Clean Earth 5m 32A Unfused Tap Off BCX4325H, 13A Fuse, 4 UK sockets, end cap
86KC03 Clean Earth 5m 32A Unfused Tap Off BCX4325H, 13A Fuse, switch, 4 UK sockets, end cap
86KC02 Clean Earth 5m 32A Unfused Tap Off BCX4325H, 13A Fuse, 6 UK sockets, end cap
86KC04 Clean Earth 5m 32A Unfused Tap Off BCX4325H, 13A Fuse, switch, 6 UK sockets, end cap
86KC05 Clean Earth 5m 32A Unfused Tap Off BCX4325H, 16A 30m RCBO, 4 UK sockets, end cap
86KC06 Clean Earth 5m 32A Unfused Tap Off BCX4325H, 16A 30m RCBO, 6 UK sockets, end cap
Please note: See page 104 for information on CMD tap offs.
Grey/Silver All BlackWhite/Silver
Metal(86 Series)
Plastic (89 Series)47
mm
59mm
43m
m
60mm
71sales line: +44 (0)1709 829511
modular power
Pre-wired infeed with Betatrak Tap off
Flexibleinterconnecting module
Unique rotatingpower sockets
A selection of interchangeable modules
to meet the changing needs of your business
A choice of switching protection modules
Protection/Switching SocketsInfeed
Features include:
• 32A internal copper busbar
• 360O rotatable sockets.• Easy fit modular
system• Integrated power and
data• Quality manufacture
and testing (Kite Mark & BSI Certified to BS 5733)
• Standard, low noise / clean earth and dual circuit options
• 32A system conforms to BS 7671 Amd 3 section 543.7 for high protective conductor currents
• Can be used to comply with BS 6396
• Termination to other tap offs are available on request
Rotasoc® is widely considered to be the industry standard for customisable under desk power as it includes a comprehensive selection of multi-socket power and data modules with 360° rotatable socket outlets, available in 32 & 16 Amp versions.
Interconnect
www.cmd-ltd.com 72
Build your own
modular power
When connecting modules together, ensure that the coloured busbar shields are colour matched and correctly aligned. Do not connect modules if shields are of different colours.
Coloured busbar shield systemStandard system Clean system Dual system
White White Red Red Red White
Step 2 Protection/SwitchingA variety of protection/switching modules are available
Step 3 Sockets32A and 16A modules are available with 2, 3 or 4 sockets
Step 5 DataChoose data or complete your system with an end cap
Step 4 Flexible InterconnectFlexible interconnect modules are available in different lengths
Step 1 InfeedNote: Some 16A infeed may include protection/switching
Please see page 84 and 85 for our range of on desk Rotasoc modules.
sytem in 5 easy steps
73sales line: +44 (0)1709 829511
To fix modules to a surface:
• Flip up all rubber screw cover caps with a flat blade screwdriver
• Insert through all holes a No 8 pozi-pan screw or M4 bolt to the required length
• Tighten the screw/bolt down to the mounting surface.• Replace the rubber screw caps
To connect the Rotasoc modules:
Connection to be made by a competent person only.
1. Check that both male and female ends have the same colour coded busbar shields
2. Turn modules over and release the grey cam-lock lever with a small screwdriver into the upright position
3. Locate the male and female ends and push together until fully closed
4. Press the grey cam-lock lever over until flush with the casing to lock the modules together Clean Earth and fused options available
360o rotating sockets can be positioned as required
modular power
www.cmd-ltd.com 74
modular power
117mm (36mm high) 95.3mm (33.1mm high)
79.3mm (56.1mm high) 162.5mm (81.6mm high)
44.8mm(35.7mm high)
44.5mm(35.7mm high)
131mm (32.9mm high)
190.9mm (32.9mm high)
250.8mm (32.9mm high)
32Amp Infeed Module 16Amp Infeed Module
BS 1362 Protection Module MCB, RCD Protection Module Protection Module
2 Gang Socket Module
3 Gang Socket Module
4 Gang Socket Module
24.5mm (31mm high)
End Cap
32Amp and 16Amp Filter Module
162.5mm (52mm high)
Flexible interconnect
162.2mm
171.7mm (33.8mm high)8.5mm
Data Module
Rotasoc dimensions:
75sales line: +44 (0)1709 829511
Standard system
Code 16 Amp Infeed 2P+E
RAB201 16A Rewirable Infeed Module Non-Switched/Non-Fused Standard
RAB202 16A Rewirable Infeed Module Neon Indicator Standard
RAB203 16A Rewirable Infeed Module Neon Switch/Non-Fused Standard
RAB003 16A Infeed Module Non-Switched/Non-Fused c/w 3m lead and 13A BS 1363 Plug Standard
RAB005 16A Infeed Module Non-Switched/Non-Fused c/w 5m lead and 13A BS 1363 Plug Standard
RAB007 16A Infeed Module Neon Indicator c/w 3m lead and 13A BS1363 Plug Standard
RAB009 16A Infeed Module Neon Indicator c/w 5m lead and 13A BS1363 Plug Standard
RAB011 16A Infeed Module Neon Switch/Non-Fused c/w 3m lead and 13A BS 1363 Plug Standard
RAB013 16A Infeed Module Neon Switch/Non-Fused c/w 5m lead and 13A BS 1363 Plug Standard
Code 32 Amp Infeed 2P+E
RAB301 32A 2P+E Rewirable Infeed Module Standard
RAB111 32A Infeed Module c/w 3m 32A Unfused Metal Conduit Tap Off Betatrak PBSX3323H Standard
RAB112 32A Infeed Module c/w 5m 32A Unfused Metal Conduit Tap Off Betatrak PBSX3325H Standard
RAB113 32A Infeed Module c/w 3m 13A Fused Metal Conduit Tap Off Betatrak PBSX3133H Standard
RAB114 32A Infeed Module c/w 5m 13A Fused Metal Conduit Tap Off Betatrak PBSX3135H Standard
RAB115 32A Infeed Module c/w 3m 32A Unfused Nylon Conduit Tap Off Betatrak PBSX3323H/KNC Standard
RAB116 32A Infeed Module c/w 5m 32A Unfused Nylon Conduit Tap Off Betatrak PBSX3325H/KNC Standard
RAB117 32A Infeed Module c/w 3m 13A Fused Nylon Conduit Tap Off Betatrak PBSX3133H/KNC Standard
RAB118 32A Infeed Module c/w 5m 13A Fused Nylon Conduit Tap Off Betatrak PBSX3135H/KNC Standard
CMD Tap Off and Infeed 3 Gang Socket Module
www.cmd-ltd.com 76
Standard system
Code Switching/Protection Modules
RAB401 BS 1362 Fuse Protection Module Standard
RAB402 BS 1362 Fuse and Switch Neon Protection Module Standard
RAB403 BS 1362 Fuse and Neon Protection Module Standard
RAB405 32A 30mA RCD Module Standard
RAB410 6A MCB Type "C" Protection Module Standard
RAB420 16A MCB Type "C" Protection Module Standard
RAB430 20A MCB Type "C" Protection Module Standard
RAB440 32A MCB Type "C" Protection ModuleStandard
RAB450 16A 30mA Residual Current Operated Circuit Breaker Type "C" Protection Module Standard
RAB460 20A 30mA Residual Current Operated Circuit Breaker Type "C" Protection Module Standard
RAB470 32A 30mA Residual Current Operated Circuit Breaker Type "C" Protection Module Standard
RAB480 16A RFI Filter Module Standard
Code Socket Modules
RAB502 2 Gang Non-fused Socket Module Black Body Grey Sockets Standard
RAB503 3 Gang Non-fused Socket Module Black Body Grey Sockets Standard
RAB504 4 Gang Non-fused Socket Module Black Body Grey Sockets Standard
RAB532 2 Gang 3.15A Individually Fused Socket Module Black Body Grey Sockets Standard
RAB533 3 Gang 3.15A Individually Fused Socket Module Black Body Grey Sockets Standard
RAB534 4 Gang 3.15A Individually Fused Socket Module Black Body Grey Sockets Standard
RAB552 2 Gang 5A Individually Fused Socket Module Black Body Grey Sockets Standard
RAB553 3 Gang 5A Individually Fused Socket Module Black Body Grey Sockets Standard
RAB554 4 Gang 5A Individually Fused Socket Module Black Body Grey Sockets Standard
Code Interconnects
RAB703 0.3m 32A Male to Female Interconnecting Nylon Conduit Standard
RAB705 0.5m 32A Male to Female Interconnecting Nylon Conduit Standard
RAB710 1m 32A Male to Female Interconnecting Nylon Conduit Standard
RAB720 2m 32A Male to Female Interconnecting Nylon Conduit Standard
RAB730 3m 32A Male to Female Interconnecting Nylon Conduit Standard
RAB740 4m 32A Male to Female Interconnecting Nylon Conduit Standard
RAB750 5m 32A Male to Female Interconnecting Nylon Conduit Standard
32 Amp 16 Amp
Code Interconnects
RAB603 0.3m 16A Male to Female Interconnecting Cable Standard
RAB605 0.5m 16A Male to Female Interconnecting Cable Standard
RAB610 1m 16A Male to Female Interconnecting Cable Standard
RAB620 2m 16A Male to Female Interconnecting Cable Standard
RAB630 3m 16A Male to Female Interconnecting Cable Standard
RAB640 4m 16A Male to Female Interconnecting Cable Standard
RAB650 5m 16A Male to Female Interconnecting Cable Standard
Standard system
77sales line: +44 (0)1709 829511
Clean system
Code 32 Amp Infeed 2P+CE+E
RAC301 32A 2P+CE+E Rewirable Infeed Module Clean
RAC111 32A Infeed Module c/w 3m 32A Unfused Metal Conduit Tap Off Betatrak PBCX4323H Clean
RAC112 32A Infeed Module c/w 5m 32A Unfused Metal Conduit Tap Off Betatrak PBCX4325H Clean
RAC113 32A Infeed Module c/w 3m 13A Fused Metal Conduit Tap Off Betatrak PBCX4133H Clean
RAC114 32A Infeed Module c/w 5m 13A Fused Metal Conduit Tap Off Betatrak PBCX4135H Clean
RAC115 32A Infeed Module c/w 3m 32A Unfused Nylon Conduit Tap Off Betatrak PBCX4323H/KNC Clean
RAC116 32A Infeed Module c/w 5m 32A Unfused Nylon Conduit Tap Off Betatrak PBCX4325H/KNC Clean
RAC117 32A Infeed Module c/w 3m 13A Fused Nylon Conduit Tap Off Betatrak PBCX4133H/KNC Clean
RAC118 32A Infeed Module c/w 5m 13A Fused Nylon Conduit Tap Off Betatrak PBCX4135H/KNC Clean
Code 16 Amp Infeed 2P+CE
RAC201 16A Rewirable Infeed Module Non-Switched/Non-Fused Clean
RAC202 16A Rewirable Infeed Module Neon Indicator Clean
RAC203 16A Rewirable Infeed Module Neon Switch/Non-Fused Clean
RAC003 16A Infeed Module Non-Switched/Non-Fused c/w 3m lead and 13A BS 1363 Plug Clean
RAC005 16A Infeed Module Non-Switched/Non-Fused c/w 5m lead and 13A BS 1363 Plug Clean
RAC007 16A Infeed Module Neon Indicator c/w 3m lead and 13A BS1363 Plug Clean
RAC009 16A Infeed Module Neon Indicator c/w 5m lead and 13A BS1363 Plug Clean
RAC011 16A Infeed Module Neon Switch/Non-Fused c/w 3m lead and 13A BS 1363 Plug Clean
RAC013 16A Infeed Module Neon Switch/Non-Fused c/w 5m lead and 13A BS 1363 Plug Clean
RCBO Protection Module Flexible Interconnect
www.cmd-ltd.com 78
Clean system
Code Switching/Protection Modules
RAC401 BS 1362 Fuse Protection Module Clean
RAC402 BS 1362 Fuse and Switch Neon Protection Module Clean
RAC403 BS 1362 Fuse and Neon Protection Module Clean
RAC405 32A 30mA RCD Module Clean
RAC410 6A MCB Type "C" Protection Module Clean
RAC420 16A MCB Type "C" Protection Module Clean
RAC430 20A MCB Type "C" Protection Module Clean
RAC440 32A MCB Type "C" Protection Module Clean
RAC450 16A 30mA Residual Current Operated Circuit Breaker Type "C" Protection Module Clean
RAC460 20A 30mA Residual Current Operated Circuit Breaker Type "C" Protection Module Clean
RAC470 32A 30mA Residual Current Operated Circuit Breaker Type "C" Protection Module Clean
RAC480 16A RFI Filter Module Clean
Code Socket Modules
RAC502 2 Gang Non-fused Socket Module Black Body Red Sockets Clean
RAC503 3 Gang Non-fused Socket Module Black Body Red Sockets Clean
RAC504 4 Gang Non-fused Socket Module Black Body Red Sockets Clean
RAC532 2 Gang 3.15A Individually Fused Socket Module Black Body Red Sockets Clean
RAC533 3 Gang 3.15A Individually Fused Socket Module Black Body Red Sockets Clean
RAC534 4 Gang 3.15A Individually Fused Socket Module Black Body Red Sockets Clean
RAC552 2 Gang 5A Individually Fused Socket Module Black Body Red Sockets Clean
RAC553 3 Gang 5A Individually Fused Socket Module Black Body Red Sockets Clean
RAC554 4 Gang 5A Individually Fused Socket Module Black Body Red Sockets Clean
Code Interconnects
RAC703 0.3m 32A Male to Female Interconnecting Nylon Conduit Clean
RAC705 0.5m 32A Male to Female Interconnecting Nylon Conduit Clean
RAC710 1m 32A Male to Female Interconnecting Nylon Conduit Clean
RAC720 2m 32A Male to Female Interconnecting Nylon Conduit Clean
RAC730 3m 32A Male to Female Interconnecting Nylon Conduit Clean
RAC740 4m 32A Male to Female Interconnecting Nylon Conduit Clean
RAC750 5m 32A Male to Female Interconnecting Nylon Conduit Clean
Code Interconnects
RAC603 0.3m 16A Male to Female Interconnecting Cable Clean
RAC605 0.5m 16A Male to Female Interconnecting Cable Clean
RAC610 1m 16A Male to Female Interconnecting Cable Clean
RAC620 2m 16A Male to Female Interconnecting Cable Clean
RAC630 3m 16A Male to Female Interconnecting Cable Clean
RAC640 4m 16A Male to Female Interconnecting Cable Clean
RAC650 5m 16A Male to Female Interconnecting Cable Clean
32 Amp 16 Amp
79sales line: +44 (0)1709 829511
Dual system
Code 32A Infeeds 4P+E+CE
RAD301 32A 4P+E+CE Rewirable Infeed Module Dual
RAD111 32A Infeed Module c/w 3m 28A Unfused Metal Conduit Tap Off Betatrak PBDX7283H Dual
RAD112 32A Infeed Module c/w 5m 28A Unfused Metal Conduit Tap Off Betatrak PBDX7285H Dual
RAD113 32A Infeed Module c/w 3m 32A Unfused Metal Conduit Tap Off Betatrak PBSX3323H+PBCX4323H Dual
RAD114 32A Infeed Module c/w 5m 32A Unfused Metal Conduit Tap Off Betatrak PBSX3325H+PBCX4325H Dual
RAD115 32A Infeed Module c/w 3m 28A Unfused Nylon Conduit Tap Off Betatrak PBDX7283H/KNC Dual
RAD116 32A Infeed Module c/w 5m 28A Unfused Nylon Conduit Tap Off Betatrak PBDX7285H/KNC Dual
RAD117 32A Infeed Module c/w 3m 32A Unfused Nylon Conduit Tap Off Betatrak PBSX3323H+PBCX4323H/KNC Dual
RAD118 32A Infeed Module c/w 5m 32A Unfused Nylon Conduit Tap Off Betatrak PBSX3325H+PBCX4325H/KNC Dual
Code 16A Infeeds 4P+E+CE
RAD201 16A Rewirable Infeed Module Non-Switched/Non-Fused Dual
RAD202 16A Rewirable Infeed Module 2 x Neon Indicator Dual
RAD203 16A Rewirable Infeed Module 2 x Neon Switch/Non-Fused Dual
RAD003 16A Rewirable Infeed Module Non-Switched/Non-Fused c/w 2 x 3m lead and 13A BS 1363 Plug Dual
RAD005 16A Infeed Module Non-Switched/Non-Fused c/w 2 x 5m lead and 13A BS 1363 Plug Dual
RAD007 16A Infeed Module 2 x Neon Indicator c/w 2 x 3m lead and 13A BS 1363 Plug Dual
RAD009 16A Infeed Module 2 x Neon Indicator c/w 2 x 5m lead and 13A BS 1363 Plug Dual
RAD011 16A Infeed Module 2 x Neon Switch/Non-Fused c/w 2 x 3m lead and 13A BS 1363 Plug Dual
RAD013 16A Infeed Module 2 x Neon Switch/Non-Fused c/w 2 x 5m lead and 13A BS 1363 Plug Dual
Code Switching/Protection Modules
RAD401 2 x BS 1362 Fuse Protection Module Dual
RAD402 2 x Switch Neon Module Dual
RAD403 2 x Neon Module Dual
RAD410 2 x 6A MCB Type "C" Protection Module Dual
RAD420 2 x 16A MCB Type "C" Protection Module Dual
RAD430 2 x 20A MCB Type "C" Protection Module Dual
RAD440 2 x 32A MCB Type "C" Protection Module Dual
Code Socket Modules
RAD502 2 Gang Non-fused Socket Module - Black Body Grey Sockets Standard/Clean Bypass Dual
RAD503 3 Gang Non-fused Socket Module - Black Body Grey Sockets Standard/Clean Bypass Dual
RAD504 4 Gang Non-fused Socket Module - Black Body Grey Sockets Standard/Clean Bypass Dual
RAD512 2 Gang Non-fused Socket Module - Black Body Red Sockets Clean/Standard Bypass Dual
RAD513 3 Gang Non-fused Socket Module - Black Body Red Sockets Clean/Standard Bypass Dual
RAD514 4 Gang Non-fused Socket Module - Black Body Red Sockets Clean/Standard Bypass Dual
www.cmd-ltd.com 80
Dual system
Code Interconnects
RAD703 0.3m 32A Male to Female Interconnecting Nylon Conduit Dual
RAD705 0.5m 32A Male to Female Interconnecting Nylon Conduit Dual
RAD710 1m 32A Male to Female Interconnecting Nylon Conduit Dual
RAD720 2m 32A Male to Female Interconnecting Nylon Conduit Dual
RAD730 3m 32A Male to Female Interconnecting Nylon Conduit Dual
RAD740 4m 32A Male to Female Interconnecting Nylon Conduit Dual
RAD750 5m 32A Male to Female Interconnecting Nylon Conduit Dual
Code Accessories
RAZ001 End Cap
RAZ020 250mm x 4.0mm Earth Cable Kit c/w fixings for 32A Infeed
RAZ010 250mm x 1.5mm Earth Cable Kit c/w fixings for 16A Infeed
Code Data Communication Modules - Socket Connection
RAF101 4 Way Communication Module 50/25mm Insert
RAF102 4 Way Communication Module 50/25mm Insert c/w conduit entry end cap
RAF107 4 Way Communication Module 37/22mm cut outs
RAF108 4 Way Communication Module 37/22mm cut outs c/w conduit entry end cap
Code Data Communication Modules - Stand Alone
RAF210 4 Way Communication Module 50/25mm Insert
RAF211 4 Way Communication Module 50/25mm Insert c/w conduit entry end cap
RAF214 4 Way Communication Module 37/22mm cut outs
RAF215 4 Way Communication Module 37/22mm cut outs c/w conduit entry end cap
Code Socket Modules (cont)
RAD532 2 Gang 3.15A Individually Fused Socket Module - Black Body Grey Sockets Standard/Clean Bypass Dual
RAD533 3 Gang 3.15A Individually Fused Socket Module - Black Body Grey Sockets Standard/Clean Bypass Dual
RAD534 4 Gang 3.15A Individually Fused Socket Module - Black Body Grey Sockets Standard/Clean Bypass Dual
RAD542 2 Gang 3.15A Individually Fused Socket Module - Black Body Red Sockets Clean/Standard Bypass Dual
RAD543 3 Gang 3.15A Individually Fused Socket Module - Black Body Red Sockets Clean/Standard Bypass Dual
RAD544 4 Gang 3.15A Individually Fused Socket Module - Black Body Red Sockets Clean/Standard Bypass Dual
RAD552 2 Gang 5A Individually Fused Socket Module - Black Body Grey Sockets Standard/Clean Bypass Dual
RAD553 3 Gang 5A Individually Fused Socket Module - Black Body Grey Sockets Standard/Clean Bypass Dual
RAD554 4 Gang 5A Individually Fused Socket Module - Black Body Grey Sockets Standard/Clean Bypass Dual
RAD562 2 Gang 5A Individually Fused Socket Module - Black Body Red Sockets Clean/Standard Bypass Dual
RAD563 3 Gang 5A Individually Fused Socket Module - Black Body Red Sockets Clean/Standard Bypass Dual
RAD564 4 Gang 5A Individually Fused Socket Module - Black Body Red Sockets Clean/Standard Bypass Dual
Code Interconnects
RAD603 0.3m 16A Male to Female Interconnecting Cable Dual
RAD605 0.5m 16A Male to Female Interconnecting Cable Dual
RAD610 1m 16A Male to Female Interconnecting Cable Dual
RAD620 2m 16A Male to Female Interconnecting Cable Dual
RAD630 3m 16A Male to Female Interconnecting Cable Dual
RAD640 4m 16A Male to Female Interconnecting Cable Dual
RAD650 5m 16A Male to Female Interconnecting Cable Dual
32 Amp 16 Amp
81sales line: +44 (0)1709 829511
On desk
Our new horizontal and vertical on desk modules work in conjunction with our under desk Rotasoc system to create the perfect modular power and data solution.
Flexibleinterconnecting
module
Choice of modules with 2, 3 and 4
360° Rotating Sockets
Metal desk fixing clamp
Fixing screws compatible for desk thickness between 20mm and 35mm
www.cmd-ltd.com 82
On desk
Code Horizontal Socket Modules
Pre-wired with 1m 16A interconnection lead - Standard Earth
RAK001 2 Gang 3.15A Individually Fused Socket Module Black Body Grey Sockets
RAK002 3 Gang 3.15A Individually Fused Socket Module Black Body Grey Sockets
RAK003 4 Gang 3.15A Individually Fused Socket Module Black Body Grey Sockets
RAK010 2 Gang Non-fused Socket Module Black Body Grey Sockets
RAK011 3 Gang Non-fused Socket Module Black Body Grey Sockets
RAK012 4 Gang Non-fused Socket Module Black Body Grey Sockets
Pre-wired with 3m power lead and 13A plug - Standard Earth
RAK020 2 Gang 3.15A Individually Fused Socket Module Black Body Grey Sockets
RAK021 3 Gang 3.15A Individually Fused Socket Module Black Body Grey Sockets
RAK022 4 Gang 3.15A Individually Fused Socket Module Black Body Grey Sockets
RAK030 2 Gang Non-fused SocketModule Black Body Grey Sockets
RAK031 3 Gang Non-fused SocketModule Black Body Grey Sockets
RAK032 4 Gang Non-fused SocketModule Black Body Grey Sockets
Code Vertical Socket Modules
Pre-wired with 1m 16A interconnection lead - Standard Earth
RAL003 2 Gang 3.15A Individually Fused Socket Module Black Body Grey Sockets
RAL002 3 Gang 3.15A Individually Fused Socket Module Black Body Grey Sockets
RAL005 2 Gang Non-fused Socket Module Black Body Grey Sockets
RAL006 3 Gang Non-fused SocketModule Black Body Grey Sockets
Pre-wired with 3m power lead and 13A plug - Standard Earth
RAL001 2 Gang 3.15A Individually Fused Socket Module Black Body Grey Sockets
RAL004 3 Gang 3.15A Individually Fused Socket Module Black Body Grey Sockets
Pre-wired with 1m 16A interconnection lead - Clean Earth
RAL012 2 Gang 3.15A Individually Fused Socket Module Black Body Red Sockets
RAL011 3 Gang 3.15A Individually Fused Socket Module Black Body Red Sockets
RAL014 2 Gang Non-fused Socket Module Black Body Red Sockets
RAL015 3 Gang Non-fused Socket Module Black Body Red Sockets
Pre-wired with 3m power lead and 13A plug - Clean Earth
RAL010 2 Gang 3.15A Individually Fused Socket Module Black Body Red Sockets
RAL013 3 Gang 3.15A Individually Fused Socket Module Black Body Red Sockets
Horizontal Module *Vertical Module
*Note: The vertical socket modules can be connected to the desk using a through desk M10 fixing bolt, which is not supplied.
83sales line: +44 (0)1709 829511
Cables & Connectors
Connector system for use with power modules, giving quick and simple installation.
• 3 pole male and female pre-moulded connectors with 1.5mm2 cable up to 7m• Cable lengths over 7m are 2.5mm2 cable due to voltage drop• Available in black or white• Connectors comply with BS 5733• Separate system for dedicated power supplies can be supplied upon request
Power accessories
Length Code
200mm 640199
300mm 640200
500mm 640201
Length Code Black Code White
0.3m 620203GST 620303GST*
0.5m 620205GST 620305GST
1m 620210GST 620310GST
1.5m 620215GST 620315GST*
2m 620220GST 620320GST
3m 620230GST 620330GST
4m 620240GST 620340GST*
Length Code Black Code White
1m 601110GST 601210GST
1.5m 601115GST 601215GST
2m 601120GST 601220GST
3m 601130GST 601230GST
4m 601140GST 601240GST
5m 601150GST 601250GST
6m 601160GST 601260GST
7m 601170GST 601270GST
8m 601179GST 601280GST*
9m 601180GST 601290GST*
10m 600965GST 601299GST*
*Note: Subject to availability and lead times.
Male 3 Pole Connector to Female 3 Pole Connector
Earth Kit
Earth leads can be provided for connection to the modules and for earth bonding between metal framed furniture in accordance with BS 6396 where relevant. These are available in a variety of lengths and terminations and consist of an earth cable, M5 ring terminal on both ends & screws.
*Note: Subject to availability and lead times.
Code Details
160834GST Male ST to female GST
160618GST Male GST to female ST
GST/ST Connector Blocks
Starter Cable 13A UK Plug to Female 3 Pole Connector
All images are for illustration purposes only.
www.cmd-ltd.com 84
16 Series Self-Fit Connectors
Suitable for terminating cables to produce mains or connector leads. We recommend that only the female is used for mains input lead applications. These connectors are rated at 16 Amps, we recommend that 1.5mm2
cable diameter is used for assembly purposes.
Power accessories
*Note: Subject to availability and lead times. **(to suit the self fit connectors)
Black White*
160035 160400*
Self fitconnector
Code Black Code White
Male 161525GST 144062GST
Female 160839GST 144061GST
Code Black Code White
161413GST 161414GST*
Mainssplitter
Code Black Code White
Standard 161415GST 161416GST*
Extended inheight**
161417GST 161418GST*
Plug Code Black Code White
Male 161419GST* 161420GST*
Female 161421GST* 161422GST*
16 Series Cable Locking Clip
16 Series Connector Blocks
• 1 Male inlet to 1 Female outlet to connect modules together without a cable
• 2 Connector blocks are required per connection• Colour options, black or white
16 Series Mains Splitter
• 1 Male inlet to 3 Female outlets, with fixing lugs, black or white
16 Series Blanking Plugs
Fuses
Code Description
440175 100 x 3.15A Fuses
440176 100 x 5A Fuses
All images are for illustration purposes only.
Male 3 Pole Connector to Female 3 Pole Connector
GST/ST Connector Blocks
85sales line: +44 (0)1709 829511
Electrical safetyBS 6396 Electrical Systems in Office Furniture & Educational Furniture
Electrical equipment and installations must be designed and tested to ensure their safety and to comply with statutory regulations, in particular the “Electricity at Work Regulations”. Relevant British Standards may be used as a means of demonstrating safety and compliance with the regulations. In the case of electrical systems in office furniture and educational furniture, the relevant standard for systems connected to the mains supply by means of a 13A plug is BS 6396.
Sockets installed in office furniture are intended to supply office equipment with a rating not exceeding 5A with BS 6396 referring to all office furniture electrical installations when completed must be tested. Section 7 of BS 6396 sets out the procedures. These tests should also be carried out on reconfigured desks and screens as well as new installations. Periodic inspections and tests must be carried out to fulfil the requirements of BS 6396 and the “Electricity at Work Regulations” in maintaining a safe working environment.
The diagrams below indicate the maximum number of socket outlets that may be connected from a single powersupply cable fed from a 13 Amp BS 1363 plug and their relevant fuse ratings.
BS 5733 General requirements for electrical accessories
BS 5733 specifies requirements and tests to check the safety in normal use of electrical accessories which are not covered by other specific British Standards. Such accessories are intended for use in household, commercial and light industrial premises where:
• The nominal supply voltage does not exceed 250 V a.c. single-phase, 50 Hz to 60 Hz or 250 V d.c.; • The rated current of the accessory does not exceed 63A.
Unless otherwise stated by the manufacturer, accessories conforming to this standard are intended for connection by cables or flexible cords conforming to BS 6004, BS 6007, BS 6500 or BS 7211. BS EN 61535
BS EN 61535 Installation couplers intended for permanent connection in fixed installations
This standard applies to two, three, four and five wire installation couplers including earth, (if provided), with a rated voltage up to and including 500V a.c. and a rated connecting capacity up to and including 10mm for permanent connection in indoor electrical installations. Installation couplers with additional contacts for voltages other than mains voltages are outside the scope of this standard.
All Products within our range which are intended for connection to the fixed wiring of the building, (such as our Betatrak® Underfloor Busbar System and Modular Lighting Systems), use components certified to BS EN 61535.
Confidence in CMD Products
At CMD our highly trained and experienced engineers are fully qualified in all aspects of compliance with BS6396 and all of our products are manufactured to BS5733 and where relevant to BS EN 61535.
5 Amp 5 Amp
3.15 Amp 3.15 Amp 3.15 AmpPlug Fuse 13 Amp
Plug Fuse 13 Amp
www.cmd-ltd.com 86
Betatrak® underfloor busbar
Slide and lock with positive latching
(prevents accidental disconnection)
32 Amp Tap offs incorporate
an unfused plug(fused available)
Various Tap off lengths available
16mmø metal flexible conduit as standard
(Black LSOH polyamide conduit available)
Colour coded for easy recognition
Low profile busbar
Busbars offer an efficient, flexible solution to underfloor power distribution as they use a click fit method for that fast and simple install. To reduce up front labour costs all busbars are tested at our manufacturing facilities meaning no onsite commissioning. Underfloor power solutions are also very low maintenance and exceptionally reliable making it the perfect solution in today’s modern construction world.
The benefits of using an Underfloor Power Distribution System• Choice: a comprehensive range of supply systems• Flexibility: can be used in new or existing layouts• Versatility: all kinds of configurations are possible including bends/corners• Safety: colour coded tap offs for easy recognition. Sliding dust covers to protect outlets • Height clearance: low profile busbar suitable for shallow floor voids• Convenience: variety of Betatrak® lengths with different socket centres. 300mm standard (150mm and
600mm available on request)
The following versions are available for both Busbar and Tap Offs:• Standard Earth• Clean Earth (CE) Low Noise Earth• Dual Circuit• Auxiliary Earth• Three Phase
www.cmd-ltd.com 88
Standard
White 63 Amp
Clean Earth (CE)
(Low Noise Earth)
Red 63 Amp
Dual Circuit
(Standard/Low Noise)
Green 63 Amp
Auxiliary
Black63 Amp
3 Phase
Blue63 Amp
Length No of Sockets Centres(mm)
3.6m 12 300 PBST3336 PBCT4336 PBDT6336 PBAT3336 PBTT5336
2.4m 8 300 PBST3324 PBCT4324 PBDT6324 PBAT3324 PBTT5324
1.8m 6 300 PBST3318 PBCT4318 PBDT6318 PBAT3318 PBTT5318
1.2m 4 300 PBST3312 PBCT4312 PBDT6312 PBAT3312 PBTT5312
Feed Unit PBSF3010/S PBCF4010/S PBDF6010 PBAF3010/S PBTF5010
Flexible Corner 1m PBSB3031H/S PBCB4031H/S PBDB6031H PBAB3031H/S PBTB5031H
2m PBSB3032H/S PBCB4032H/S PBDB6032H PBAB3032H/S PBTB5032H
Flexible Corner Kit PBSB3000/S PBCB4000/S PBDB6000 PBAB3000/S PBTB5000
Betatrak® underfloor busbar
Busbar3m tap offs provide full coverage when busbar is laid out on 5m centres.
Floor BoxesTypical layout: 1 floor box for every 10m2
Typical Floor Layouts
PE N L3 L2 L1PE N LCE N L CE N1 L1 N2 L2N L
Betatrak® BST 3336
Betatrak® BST 3336
Betatrak® BST 3336
Area covered by tap off lead maximum lead
5 m
5 m
Betatrak® BST 3336
Betatrak® BST 3336
Betatrak® BST 3336
2.5 m
2.5 m
89sales line: +44 (0)1709 829511
The 63 Amp Betatrak® System caters for single phase standard, clean earth (CE) low noise, auxiliary, three phase or dual applications. Betatrak® comes in lengths of 1.2m, 1.8m, 2.4m or 3.6m with tap off positions provided at 300mm as standard (Note: 150mm & 600mm available on request). As a result, the system is extremely versatile and suitable for high to low density tap off requirements.
All integral connectors and tap off plug sockets are colour coded to avoid any possible errors during assembly. For maximum safety each operates a shutter on insertion to ensure no accidental contact can be made.
Installation
Betatrak® used within raised access floors is normally arranged in parallel runs with the feed units to the Betatrak® orientated towards the incoming supply. This offers an economic format inherent in long straight runs. Spacing should be a maximum of 5 metres between each length of track and 2.5 metres from the perimeter when using a standard 3 metre tap off to a floor box.
Attention should be given to the total power requirements to avoid exceeding the maximum power rating of the Busbar.
How to install the Busbar
Starting with the feed unit, remove the dust cover over the colour coded socket and simply snap the integral coupler, pre-installed on the busbar, into the feed socket. The next length of track is then fitted to the socket end of the first length of busbar as previously described, this is then repeated for the following lengths until the run is complete. On the final length of busbar section the dust cover supplied is fitted on the final unused coupling point to protect against the ingress of foreign contaminants. The feed unit is then secured via the slots in the base and the busbar every 1200mm (max) by using the mounting brackets provided.
CMD is registered by BSI to BS EN ISO 9001 & BS EN ISO 14001. Betatrak® is designed to comply with regulation 434.2 of BS 7671: 2008 Amd 3 (IEE Wiring Regulations) & 543.7 earthing requirements for the installation of equipment having high protective conductor currents.
The scope of Reg. 543.7.1.3 requires that every final circuit is intended to supply one or more items of equipment, where the total protective conductor current is likely to exceed 10mA. in normal use, shall have a high protective connection.
Betatrak® underfloor busbar
47mm End Feed (H)
300mm pitch
21mm (H)
47mm (H) with plug
40mm (H) with bracket
107mm (W) with fixing lugs
78mm (W) with bracket
www.cmd-ltd.com 90
Electrical CharacteristicsRated Current 63 AmpsRated Voltage 240/415 VoltsFrequency 50 HzConditional Short Circuit Rating (Protection device Bs88 fuse) 16 KAMax withstand current 10 kA PeakShort time withstand current 1200A for 0.4 SecVolt Drops (Line & Neutral) Busbars 3.2 mV/A/m
Feed Unit 0.4 mV/ATrack Coupler 0.6 mV/A/mTap off Connection 0.5 mV/A+4mm2 Cable 11.00 mV/A/m+2.5mm2 18.00 mV/A/mFlexible Corner Unit 3.6 mV/A+10mm2 Cable (1.2m) 4.7 mV/A/m
Earth Fault Loop Impedance Line to Earth (Housing) 3.0 mΩ/mLine to Earth (Bar) 3.2 mΩ/mLine to Earth (Bar + Housing) 2.5 mΩ/mFeed Unit 0.8 mΩTrack Coupler 0.6 mΩTap off Connection 0.6 mΩ+4m2 Cable 11.0 mΩ/m+2.5mm2 & 4mm2 Cable 14.5 mΩ/mFlexible Corner Unit 4.0 mΩ+10mm2 Cable 4.7 mΩ/m
Mechanical DataNumber of Copper Conductors 2, 3, or 5Busbar Cross-section Area 14 mm2
Betatrak® Basing Copper Equivalent (Where casing is protective Earth) 14 mm2
Cable Termination Capacity 16 mm2
Tap off Cable 32Amp (BS 7211) 4.0 mm2
Tap off Cable 13Amp fused (BS 7211) 2.5 mm2
Tap off Conduit Sizes Ø16 or Ø20 mmFlexible Corner Unit Cable (BS 7211) 10 mm2
Flexible Interlink Conduit Ø25 mmFeed Conduit Entry 1 or 2 x Ø25 mmIP Rating BS EN 60529 4XMinimum void depth (track + tap off) 59 mmMaterial SpecificationBetatrak® Casing Galvanised SteelBusbars High Conductivity CopperBusbar Insulators & Coupling Mould Flame Retardant PolycarbonateCouple Contacts CopperFeed Unit Terminals Brass Silver PlatedTap off Socket & Plug Mouldings Flame Retardant PolycarbonateTap off Shutter PolyesterTap off Plug Ins BrassTap off Cable LSOH BS 7211Flexible Corner Cable Tri Rated BS 6231Ambient Temperature Control FactorsTemperature 25C 30C 35C 40C 50CFactor 1.13 1.07 1.0 0.93 0.75
Betatrak product has been independently tested to comply with BS EN 60439-2 2000 & IEC 60439-2: 2000.The product is designed to conform to BS EN 61534-22.
Betatrak® underfloor busbar
91sales line: +44 (0)1709 829511
Tap off units
Standard earth Clean earth Dual circuit Auxiliary earth 3 phase
PBDX 7283H* PBTX 5283H**
PBSX 3323H PBCX 4323HPBSX 3323H
PBCX 4323HPBAX 3323H
BTX 3323H
1, 2 or 3
PBSX 3133H PBCX 4133HPBSX 3133H
PBCX 4133HPBAX 3133H
BTX 3133H
1, 2 or 3
PBDX 7283H* PBTX 5285H**
PBSX 3325H PBCX 4325HPBSX 3325H
PBCX 4323HPBAX 3325H
BTX 3325H
1, 2 or 3
PBSX 3135H PBCX 4135HPBSX 3135H
PBCX 4135HPBAX 3135H
BTX 3135H
1, 2 or 3
Socket key codes
3m unfused
3m unfused 32 Amp
3m fused 13 Amp
5m unfused 28 Amp
5m unfused 32 Amp
5m fused 13 Amp
Tap offs are colour coded and non-interchangeable between busbar types. The slide locking, positive latching tap off plug prevents accidental disconnection and can be added to or removed from the busbar while the system is live. All 3 metre, 32 Amp tap offs incorporate an unfused plug, and as standard, 16mmØ metal flexible conduit enclosing 3 metres of 4mm2 cables. These units are designed to comply with Regulation 434.2.1 of BS 7671:2008 Amd 3. 5 metre unfused tap offs are also available for use with individual track runs that are rated at no more than 32Amp, where the protection of the tap off against both overload and fault current is provided by the track protective device.
CMD tap off units conform to the high integrity protective requirement by virtue of using a protective conductor of 4mm enclosed within a flexible conduit, thus providing additional protection against mechanical damage.
Betatrak® underfloor busbar
The benefits of using a CMD Tap off
• Choice: a comprehensive range of supply versions
• Flexibility: can be used in new or existing layouts• Safety: all units are designed to comply with
regulation 434.2.1 of BS 7671: 2008 Amd 3• Convenience: all tap offs are colour coded
& non-interchangeable with slide locking and positive latching to prevent accidental disconnection
Colour coded
Slide locking
www.cmd-ltd.com 92
Betatrak® underfloor busbar32 Amp 3 metre tap off
32 Amp 3 metre tap off unit is comprised of an unfused plug with 16mmØ flexible metal conduit with integral 3m x 4mm2 cables.
These units are designed to comply with regulations 434.2.1(i) BS 7671:2008 Amd 3 by virtue of the following:
1. Maximum length of cable is <3 metres.
2. Minimum risk of faults as the item is factory assembled and fully tested.
3. Fully protected by flexible steel conduit located within raised access floor that offers further protection.
5 metre tap off unit
Tap off units in excess of 3 metres should only be used if they contain a fuse or the busbar is protected by a 32Amp rated protective device.
Mechanical data
Tap off cable 32 Amp (BS 7211) 4.0 mm2
Tap off cable 13 Amp fused (BS 7211) 2.5 mm2
Tap off conduit sizes Ø16 or Ø20 mm
Tap off socket & plug mouldings Flame retardant polycarbonate
Tap off shutter Polyester
Tap off plug pins Brass
Tap off cable LSOH BS 7211
Flexible corner cable Tri rated BS 6231
All tap off units comply with 17th Edition Wiring Regulations Section 543.7 (High Integrity Earthing).
Numerous configurations of tap off units including fuse options are available on request. Longer lengths available on request. CMD tap off units conform to the high integrity protective requirement by virtue of using a protective conductor of 4mm enclosed within a flexible conduit, thus providing additional protection against mechanical damage.*These tap offs have 2 circuits (1 x standard & 1 x clean earth) rated at 25 Amp**These tap offs are 3 Phase (L1, L2, L3, N, E) rated at 28 Amp
Mechanical data Track type Tap off type
Standard earthWhite 63 Amp
Auxiliary earth Black63 Amp
Clean earth (CE) (low noise earth) Red 63 Amp
3 phaseBlue63 Amp
Dual circuit(standard/low noise)Green63 Amp
PE N L3 L2 L1
PE N L
CE N L
CE N1 L1 N2 L2
N L
93sales line: +44 (0)1709 829511
Betatrak® underfloor busbar
PE N L
CE N L
N L
Code Description
Betatrak®
PBST3336 3.6 Metre Length
PBST3324 2.4 Metre Length
PBST3318 1.8 Metre Length
PBST3312 1.2 Metre Length
PBSF3010/S Feed Unit c/w End Stop
PBSB3000/S Flexible Corner Kit
PBSB3031H/S Flexible Corner - 1 Metre
PBSB3032H/S Flexible Corner - 2 Metre
Tap Offs
PBSX3323H 3 Metre Tap off 32 Amp Unfused
PBSX3325H 5 Metre Tap off 32 Amp Unfused
PBSX3133H 3 Metre Tap off 13 Amp Fused
PBSX3135H 5 Metre Tap off 13 Amp Fused
Standard Earth - 63 Amp
Auxiliary Earth - 63 Amp
Clean Earth (CE) - 63 Amp
Code Description
Betatrak®
PBAT3336 3.6 Metre Length
PBAT3324 2.4 Metre Length
PBAT3318 1.8 Metre Length
PBAT3312 1.2 Metre Length
PBAF3010/S Feed Unit c/w End Stop
PBAB3000/S Flexible Corner Kit
PBAB3031H/S Flexible Corner - 1 Metre
PBAB3032H/S Flexible Corner - 2 Metre
Tap Offs
PBAX3323H 3 Metre Tap off 32 Amp Unfused
PBAX3325H 5 Metre Tap off 32 Amp Unfused
PBAX3133H 3 Metre Tap off 13 Amp Fused
PBAX3135H 5 Metre Tap off 13 Amp Fused
Code Description
Betatrak®
PBCT4336 3.6 Metre Length
PBCT4324 2.4 Metre Length
PBCT4318 1.8 Metre Length
PBCT4312 1.2 Metre Length
PBCF4010/S Feed Unit c/w End Stop
PBCB4000/S Flexible Corner Kit
PBCB4031H/S Flexible Corner - 1 Metre
PBCB4032H/S Flexible Corner - 2 Metre
Tap Offs
PBCX4323H 3 Metre Tap off 32 Amp Unfused
PBCX4325H 5 Metre Tap off 32 Amp Unfused
PBCX4133H 3 Metre Tap off 13 Amp Fused
PBCX4135H 5 Metre Tap off 13 Amp Fused
www.cmd-ltd.com 94
Betatrak® underfloor busbar
PE N L3 L2 L1
CE N1 L1 N2 L2
Dual Circuit - 63 Amp
3 Phase - 63 Amp
Code Description
Betatrak®
PBDT6336 3.6 Metre Length
PBDT6324 2.4 Metre Length
PBDT6318 1.8 Metre Length
PBDT6312 1.2 Metre Length
PBDF6010 Feed Unit c/w End Stop
PBDB6000 Flexible Corner Kit
PBDB6031H Flexible Corner - 1 Metre
PBDB6032H Flexible Corner - 2 Metre
Tap Offs
PBDX7283H 3 Metre Tap off 25 Amp Unfused Dual Circuit
PBDX7285H 5 Metre Tap off 25 Amp Unfused Dual Circuit
Code Description
Betatrak®
PBTT5336 3.6 Metre Length
PBTT5324 2.4 Metre Length
PBTT5318 1.8 Metre Length
PBTT5312 1.2 Metre Length
PBTF5010 Feed Unit c/w End Stop
PBTB5000 Flexible Corner Kit
PBTB5031H Flexible Corner - 1 Metre
PBTB5032H Flexible Corner - 2 Metre
Tap Offs
PBTX3323H-1 3 Metre Tap off 32 Amp Unfused
PBTX3325H-1 5 Metre Tap off 32 Amp Unfused
PBTX3133H-1 3 Metre Tap off 13 Amp Fused
PBTX3135H-1 5 Metre Tap off 13 Amp Fused
NB: Add suffix -1, -2 or -3 to indicate required phase configuration of the above 3 Phase Tap Offs E.G. PBTX3323H-1
Non Standard Tap Offs
Code Description
Betatrak® Non Standard Tap Offs 32 Amp Neutrik Tap Offs
PPA8284 5m, 32 Amp unfused, Std Earth tap off c/w 32 Amp Neutrik (For Std earth & Std earth/607)
PPA7842 5m, 32 Amp unfused, Std Auxiliary Earth Tap off c/w 32 Amp Neutrik (For Std earth & Std earth/607)
PPA8306 5m, 32 Amp unfused, Clean Earth Tap off c/w 32 Amp Neutrik (For C/E & C/E 607)
Alphatrak® Non Standard Tap Offs Standard Earth
PASX3323H 3 Metre Tap off 32 Amp Unfused
PASX3325H 5 Metre Tap off 32 Amp Unfused
Alphatrak® Non Standard Tap Offs Clean Earth
PACX4323H 3 Metre Tap off 32 Amp Unfused
PACX4325H 5 Metre Tap off 32 Amp Unfused
95sales line: +44 (0)1709 829511
Shallow flush floor trunking
Our access floor boxes are available for shallow screed trunking.
The underside of the box must be set lower into the floor to enable cables to pass under the socket outlet plates whilst maintaining lids to finish level with the screed.
The carpet trim and lid assembly are manufactured in a polycarbonate ABS moulding which has two individual hinged cable outlets coloured in dark grey. The lid is reinforced by a 3mm steel plate and has a carpet recess of 6.5mm.
NB This box is really a 4 compartment style with double width compartments. Utilise the 4 compartment accessory plates i.e you can fit two plates in the power compartment and one plate to the other two compartments.
Our Shallow Flush Floor trunking system has been designed for the distribution of and access to power and data services in screeded floors, particularly where flexibility in the positioning of access floor boxes are required.
Shallow Flush Floor Trunking System consists of three main elements:
• 2m trunking lengths with a range of junction units, bends and end stops.
• A shallow flush floor access box with an overall depth of 75mm. Boxes to be located at the end of trunking lengths.
• A wide range of power and data socket plates.
The trunking and accessories are manufactured in self-coloured pre-galvanised steel. The trunking is supplied in two metre lengths, complete with 2 x 1 metre lengths of lid secured by means of flush, all steel turnbuckle fasteners. Each length of trunking is supplied with one external fitting connector which is fully removable. Lids are manufactured from 3mm thick galvanised steel and it is recommended that the trunking is installed on a ribbon screed or similar to ensure support along the entire length. A comprehensive range of junctions, riser bends and sealing ends are available for use with the trunking.
2 Compartment Trunking (38/50mm x 150mm) 3 Compartment Trunking (38/50mm x 228mm)
flush flush
Access Floor Box
Anti-trip facility
2/3 compartment
Self closing handle
Moulded polycarbonate ABS (RAL 7031)
Code Description
PPS275G/SFT/382 Compartment 38mm x 150mm
75mm deep trunking floor box
PPS275G/SFT/502 Compartment 50mm x 150mm
75mm deep trunking floor box
PPS375G/SFT/383 Compartment 38mm x 228mm
75mm deep trunking floor box
PPS375G/SFT/503 Compartment 50mm x 228mm
75mm deep trunking floor box
www.cmd-ltd.com 96
Shallow flush floor trunking
Tee Junction Box Cross Junction Box Angle Junction Box Riser Bend (Back Entry)
Riser Bend End Cap
Code Description
2 Compartment - 38mm x 150mm
PXFTTKG2/38/150 Flush Trunking 38mm x 150mm x 2m
PXFTRB/2/38/150 Flush Trunking Riser Bend 38mm x 150mm
PXFTRB238/150BE Flush Riser Bend (Back Entry) 38mm x 150mm
PXFTCON2/38/150 Flush Connector 38mm x 150mm
PXFTEC/2/38/150 Flush End Cap 38mm x 150mm
PXFTJBA2/38/150 Flush Angle Junction Box 38mm x 150mm x 75mm
PXFTJBT2/38/150 Flush Tee Junction Box 38mm x 150mm x 75mm
PXFTJBX2/38/150 Flush Cross Junction Box 38mm x 150mm x 75mm
2 Compartment - 50mm x 150mm
PXFTTKG2/50/150 Flush Trunking 50mm x 150mm x 2m
PXFTRB/2/50/150 Flush Trunking Riser Bend 50mm x 150mm
PXFTRB250/150BE Flush Riser Bend (Back Entry) 50mm x 150mm
PXFTCON2/50/150 Flush Connector 50mm x 150mm
PXFTEC/2/50/150 Flush End Cap 50mm x 150mm
PXFTJBA2/50/150 Flush Angle Junction Box 50mm x 150mm x 75mm
PXFTJBT2/50/150 Flush Tee Junction Box 50mm x 150mm x 75mm
PXFTJBX2/50/150 Flush Cross Junction Box 50mm x 150mm x 75mm
3 Compartment - 38mm x 228mm
PXFTTKG3/38/228 Flush Trunking 38mm x 228mm x 2m
PXFTRB/3/38/228 Flush Trunking Riser Bend 38mm x 228mm
PXFTRB338/228BE Flush Riser Bend (Back Entry) 38mm x 228mm
PXFTCON3/38/228 Flush Connector 38mm x 228mm
PXFTEC/3/38/228 Flush End Cap 38mm x 228mm
PXFTJBA3/38/228 Flush Angle Junction Box 38mm x 228mm x 75mm
PXFTJBT3/38/228 Flush Tee Junction Box 38mm x 228mm x 75mm
PXFTJBX3/38/228 Flush Cross Junction Box 38mm x 228mm x 75mm
3 Compartment - 50mm x 228mm
PXFTTKG3/50/228 Flush Trunking 50mm x 228mm x 2m
PXFTRB/3/50/228 Flush Trunking Riser Bend 50mm x 228mm
PXFTRB350/228BE Flush Connector 50mm x 228mm
PXFTCON3/50/228 Flush Connector 50mm x 228mm
PXFTEC/3/50/228 Flush End Cap 50mm x 228mm
PXFTJBA3/50/228 Flush Angle Junction Box 50mm x 228mm x 75mm
PXFTJBT3/50/228 Flush Tee Junction Box 50mm x 228mm x 75mm
PXFTJBX3/50/228 Flush Cross Junction Box 50mm x 228mm x 75mm
97sales line: +44 (0)1709 829511
Access Floor Box
Our access floor boxes are available for flush floor trunking and come complete as a ‘frame & lid’ with a choice of accessory plates to suit your requirements. Our boxes are designed to fit into the trunking anywhere along the system layout excluding junction points.
Carpet trim and lid assembly are manufactured in a polycarbonate ABS moulding which has two individual hinged cable outlets coloured dark grey. The lid is reinforced by a 3mm steel plate. Carpet recess is 6.5mm.
Flush floor trunking
Choose from a wide selection of accessory
plates
3 compartmentfloor boxes
Flush floor trunking is supplied in 2 metre lengths. 400mm lengths of removable lid are fitted which are interchangeable with an access floor box of the same length, thus giving the designer flexibility of positioning within a screeded floor installation.
• Lids are manufactured from 3mm thick galvanised steel which are fixed to the trunking body by countersunk zinc plated steel turnbuckle fasteners, providing speed of fitting by the installer and maximum rigidity of the finished product
• 2 or 3 compartments available
• It is advisable that all lid sections are fitted during screeding. This will prevent any slight inward movement to the sides of trunking body
Moulded polycarbonate ABS (RAL 7031)
Code Description
PP22265G/FL
2 Compartment 65mm deep floor box. This box is a 2 compartment. Utilise the 4 compartment accessory plates.
PP22365G/FL
3 Compartment 65mm deep floor box. This box is a 3 compartment. Utilise the 3 compartment accessory plates.
Cable retainer clips as standard
2 compartmentfloor boxes
www.cmd-ltd.com 98
Flush floor trunking
Riser Bend (Back Entry)
Riser Bend
End Cap
Trunking Components
Tee Junction Box
3 Compartment (360mm x 65mm)2 Compartment (235mm x 65mm)
Code Description
2 Compartment - 235mm x 65mm
PXFTTKG2/65/235 Flush Trunking 235mm x 65mm x 2m
PXFTRB/2/65/235 Flush Riser Bend 235mm x 65mm
PXFTRB265/235BE Flush Riser Bend (Back Entry) 360mm x 65mm
PXFTCON2/65/235 Flush Connector 235mm x 65mm
PXFTEC/2/65/235 Flush End Cap 235mm x 65mm
PXFTJB/2/65/235 Flush Tee Junction Box 235mm x 65mm x 75mm
3 Compartment - 360mm x 65mm
PXFTTKG3/65/360 Flush Trunking 360mm x 65mm x 2m
PXFTRB/3/65/360 Flush Riser Bend 360mm x 65mm
PXFTRB365/360BE Flush Riser Bend (Back Entry) 235mm x 65mm
PXFTCON3/65/360 Flush Connector 360mm x 65mm
PXFTEC/3/65/360 Flush End Cap 360mm x 65mm
PXFTJB/3/65/360 Flush Tee Junction Box 360mm x 65mm x 75mm
Connector Plate
99sales line: +44 (0)1709 829511
Buried underfloor trunkingOur buried underfloor trunking is designed for placing on the constructional concrete slab, to be completely covered when the final floor screed is laid and the service outlet positions fixed.
Our steel underfloor trunking is manufactured in 2 metre lengths with two or three compartments being the most commonly used.
The trunking lengths are a total welded construction with no need to couple together loose channel sections and each length is joined together by a saddle clamp and plate, which prevent any ingress of screed into the duct.
Buried Junction boxes are supplied with flange couplers and blank plates to enable use as angles, tee or 4 way. Each box comes complete with fly-over for cable segregation. Junction boxes cannot be used to house sockets or data outlets. Carpet recess is 6mm.
Our access floor boxes are available for buried underfloor trunking and come with a choice of accessory plates to suit your requirements.
Carpet trim and lid assembly are manufactured in a Polycarbonate ABS moulding which has two individual hinged cable outlets coloured dark grey. The lid is reinforced by a 3mm steel plate. Carpet recess is 6.5mm.
This box is really a 4 compartment style with a double width compartment for Power. Utilise the 4 compartment accessory plates i.e. you can fit two plates in the power side and one plate each in the other two compartments.
Tee Junction Box
Code Description
PPS99275G/FT/25 2 compartment 75mm deep floorbox to suit 150mm x 25mm trunking
PPS99275G/FT/50 2 compartment 75mm deep floorbox to suit 150mm x 50mm trunking
PPS99375G/FT/25 3 compartment 75mm deep floorbox to suit 225mm x 25mm trunking
PPS99375G/FT/50 3 compartment 75mm deep floorbox to suit 225mm x 50mm trunking
Code Description
PXFTJB/2/25/GS Buried Junction Box 150mm x 25mm
PXFTJB/2/50 Buried Junction Box 150mm x 50mm
PXFTJB/3/25 Buried Junction Box 225mm x 25mm
PXFTJB/3/50/75 Buried Junction Box 225mm x 50mm
Access floor box
www.cmd-ltd.com 100
Buried underfloor trunkingTrunking Components
Flat Bend
Riser Bend
Riser Bend (Back Entry)
End Cap
Connector Plate
2 Compartment Trunking (150mm x 50mm) 3 Compartment Trunking (225mm x 50mm)
Code Description
3 Compartment - 225mm x 50mm
PXFTTKG/3/50 Buried Trunking 225mm x 50mm x 2m
PXFTRB/3/50 Buried Riser Bend 225mm x 50mm
PXFTSU/3/50/100 Buried Step Down 225mm x 50mm
PXFTCONN/3/50 Buried Connector Plate 225mm x 50mm
PXFTRB/3/50/BE Buried Riser Bend (Back Entry) 225mm x 50mm
PXFTEC/3/50 Buried End Cap 225mm x 50mm
PXFTFB/3/50 Buried Flat Bend 225mm x 50mm
3 Compartment - 225mm x 25mm
PXFTTKG/3/25 Buried Trunking 225mm x 25mm x 2m
PXFTRB/3/25 Buried Riser Bend 225mm x 25mm
PXFTCONN/3/25 Buried Connector Plate 225mm x 25mm
PXFTRB/3/25/BE Buried Riser Bend (Back Entry) 225mm x 25mm
PXFTEC/3/25 Buried End Cap 225mm x 25mm
PXFTFB/3/25 Buried Flat Bend 225mm x 25mm
2 Compartment - 150mm x 50mm
PXFTTKG2/150/50 Buried Trunking 150mm x 50mm x 2m
PXFTRB/2/150/50 Buried Riser Bend 150mm x 50mm
PXFTCON2/150/50 Buried Connector Plate 150mm x 50mm
PXFTRB250/150BE Buried Riser Bend (Back Entry) 150mm x 50mm
PXFTEC/2/50 Buried End Cap 150mm x 50mm
PXFTFB/2/50 Buried Flat Bend 150mm x 50mm
2 Compartment - 150mm x 25mm
PXFTTKG2/150/25 Buried Trunking 150mm x 25mm x 2m
PXFTRB/2/150/25 Buried Riser Bend 150mm x 25mm
PXFTCON2/150/25 Buried Connector Plate 150mm x 25mm
PXFTRB250/150BE Buried Riser Bend (Back Entry) 150mm x 25mm
PXFTEC/2/25 Buried End Cap 150mm x 25mm
PXFTFB/2/25 Buried Flat Bend 150mm x 25mm
101sales line: +44 (0)1709 829511
• Self Closing
• Designed with ‘Anti-Trip’ facility
Robust cable outlet
Handle
• RAL 7031
Blue/grey moulded polycarbonate ABS
Access floor box
• Wide range of accessory plates
• Can be prewired with Betatrak®
tap offs
• Deeper versions available
• Quick removal with services fitted
• Installation tolerance of -0/+3mm
• Fixes to floor thicknesses of 15-50mm
Fully configurable floor box
Fast fit advantages
One piece ‘fast fit’ (20 series) - One piece back box
Individual ‘fast fit’ (20A series) - Individual box bases for each compartment
Screed/Screw fixed/Stainless (99 series) - Screed and stainless steel boxes available. Stainless suited for more prestigious spaces e.g. reception areas
Optional lockable lid
Added security allows access
by competent personnel
• 6.5mm
Carpet inlay
www.cmd-ltd.com 102
Floor box spares
Code Description
Fast Fit Box Spares (Series 20 & 20A)
PPS2001G Lid & Trim Assembly
PPS2020/15 15mm Collar Assembly - add to 85mm box to make it 100mm
PPS2020/30 30mm Collar Assembly - add to 85mm box to make it 115mm
PPS2020/45 45mm Collar Assembly - add to 85mm box to make it 130mm
PPS2011G Cable Outlet Brackets - each
PPB4310 Cable Guides - each
PPB4159 Handle Assembly - each
PPS2030 Hinge Assembly (Pair)
Floor box Spares Screw Fix (Series 99)
PPS9901G Lid & Trim Assembly
PPS9002 Mounting Frame (25mm)
PPS9005 Mounting Frame (50mm)
PPS9007 Mounting Frame (70mm)
PPS2011G Cable Outlet Brackets - each
PPB4310 Cable Guides - each
PPB4159 Handle Assembly - each
PPS2030 Hinge Assembly (Pair)
Screw Fix (Series 90)
PPS9011G Cable Outlet Brackets - each
Screw Fix (Series 93)
PPS9301G Lid & Trim Assembly
PPS9325 Box Base Assembly
PPS9302 Mounting Frame (25mm)
PPS9311G Cable Outlet Brackets - each
PPB1109 Cable Guides - each
PPB1111S Handle Assembly - each
PX16003 Handle Assembly - clips
PPS9030 Hinge Assembly (Left & Right Hinges & Screws - Pair)
Floor box Spares
Conduits
Code Description
Metal Conduit
PX4023C 3 Metre x 20mm Metal Conduit c/w Glands
PX4025C 5 Metre x 20mm Metal Conduit c/w Glands
PX4053C 3 Metre x 25mm Metal Conduit c/w Glands
PX4055C 5 Metre x 25mm Metal Conduit c/w Glands
103sales line: +44 (0)1709 829511
Our one piece 20 Series ‘Fast Fit’ access floor box has been designed to meet the demands of the modern day working environment.
One piece floor boxes
Plug
Spa
ce
Sock
et S
pace
• Fast and simple tool free fixing mechanism
• Easy access for carpet fitting: the lid and trim is removed in seconds
• Quick release lid for easy access to accessory plates
• Can be pre-fitted with socket outlet and tap off unit
• Self closing lid
• Non-trip cable outlet brackets
• 3 and 4 compartment boxes are the same overall size. Compartment sizes:
� 3 compartment: 100mm x 175mm
� 4 compartment: 75mm x 175mm
• 85mm standard depth (other sizes available, see table opposite)
Overall Depth Plug Space Socket Space
85mm 30mm 45mm
100mm 45mm 45mm
115mm 60mm 45mm
130mm 75mm 45mm
Code Description
One Piece Unwired Floor box, Grey Trim
PP20385G Standard ‘Fast Fit’ 85mm deep
PP20310G Standard 'Fast Fit' 100mm deep
PP20311G Standard 'Fast Fit' 115mm deep
PP20313G Standard 'Fast Fit' 130mm deep
Add Suffix /KL Additional overcost to fit a Key Lock to a floor box lid
350mm
332mm -0/+3 Cutout
200m
m -
0/+
3 C
utou
t
218m
m
3 Compartment
Code Description
One Piece Unwired Floor box, Grey Trim
PP20485G Standard ‘Fast Fit’ 85mm deep
PP20410G Standard 'Fast Fit' 100mm deep
PP20411G Standard 'Fast Fit' 115mm deep
PP20413G Standard 'Fast Fit' 130mm deep
Add Suffix /KL Additional overcost to fit a Key Lock to a floor box lid
4 Compartment
Ove
rall
Dep
th
Deeper options available
Optional lockable lid
www.cmd-ltd.com 104
One piece floor boxes
Code Description
3m Standard Earth White Plug
P20385G/BS3U104 1 x Twin 13A Switched Socket
P20385G/BS3U207 2 x Twin 13A Switched Sockets
P20385G/BS3U113 1 x Twin 13A Switched RCD Socket
P20385G/BS3U221 2 x Twin 13A Switched RCD Sockets
5m Standard Earth White Plug
P20385G/BS5U102 1 x Twin 13A Switched Socket
P20385G/BS5U204 2 x Twin 13A Switched Sockets
P20385G/BS5U108 1 x Twin 13A Switched RCD Socket
P20385G/BS5U213 2 x Twin 13A Switched RCD Sockets
3 Compartment 4 Compartment
3 Compartment 4 Compartment
3 Compartment 4 Compartment
Standard Earth One piece pre-wired floor box c/w 3m or 5m 32A unfused Betatrak® tap off
Clean Earth One piece pre-wired floor box c/w 3m or 5m 32A unfused Betatrak® tap off
Auxiliary Standard Earth One piece pre-wired floor box c/w 3m or 5m 32A unfused Betatrak® tap off
Code Description
3m Standard Earth White Plug
P20485G/BS3U102 1 x Twin 13A Switched Socket
P20485G/BS3U204 2 x Twin 13A Switched Sockets
P20485G/BS3U103 1 x Twin 13A Switched RCD Socket
P20485G/BS3U209 2 x Twin 13A Switched RCD Sockets
5m Standard Earth White Plug
P20485G/BS5U101 1 x Twin 13A Switched Socket
P20485G/BS5U201 2 x Twin 13A Switched Sockets
P20485G/BS5U102 1 x Twin 13A Switched RCD Socket
P20485G/BS5U203 2 x Twin 13A Switched RCD Sockets
Code Description
3m Clean Earth Red Plug
P20385G/BC3U101 1 x Twin 13A Switched Socket
P20385G/BC3U205 2 x Twin 13A Switched Sockets
P20385G/BC3U110 1 x Twin 13A Switched RCD Socket
P20385G/BC3U220 2 x Twin 13A Switched RCD Sockets
5m Clean Earth Red Plug
P20385G/BC5U103 1 x Twin 13A Switched Socket
P20385G/BC5U203 2 x Twin 13A Switched Sockets
P20385G/BC5U108 1 x Twin 13A Switched RCD Socket
P20385G/BC5U207 2 x Twin 13A Switched RCD Sockets
Code Description
3m Clean Earth Red Plug
P20485G/BC3U100 1 x Twin 13A Switched Socket
P20485G/BC3U202 2 x Twin 13A Switched Sockets
P20485G/BC3U102 1 x Twin 13A Switched RCD Socket
P20485G/BC3U207 2 x Twin 13A Switched RCD Sockets
5m Clean Earth Red Plug
P20485G/BC5U101 1 x Twin 13A Switched Socket
P20485G/BC5U201 2 x Twin 13A Switched Sockets
P20485G/BC5U103 1 x Twin 13A Switched RCD Socket
P20485G/BC5U203 2 x Twin 13A Switched RCD Sockets
Code Description
3m Auxiliary Earth Black Plug
P20385G/BA3U102 1 x Twin 13A Switched Socket
P20385G/BA3U203 2 x Twin 13A Switched Sockets
P20385G/BA3U105 1 x Twin 13A Switched RCD Socket
P20385G/BA3U206 2 x Twin 13A Switched RCD Sockets
5m Auxiliary Earth Black Plug
P20385G/BA5U101 1 x Twin 13A Switched Socket
P20385G/BA5U202 2 x Twin 13A Switched Sockets
P20385G/BA5U102 1 x Twin 13A Switched RCD Socket
P20385G/BA5U204 2 x Twin 13A Switched RCD Sockets
Code Description
3m Auxiliary Earth White Plug
P20485G/BA3U102 1 x Twin 13A Switched Socket
P20485G/BA3U204 2 x Twin 13A Switched Sockets
P20485G/BA3U103 1 x Twin 13A Switched RCD Socket
P20485G/BA3U207 2 x Twin 13A Switched RCD Sockets
5m Auxiliary Earth White Plug
P20485G/BA5U100 1 x Twin 13A Switched Socket
P20485G/BA5U201 2 x Twin 13A Switched Sockets
P20485G/BA5U101 1 x Twin 13A Switched RCD Socket
P20485G/BA5U203 2 x Twin 13A Switched RCD Sockets
105sales line: +44 (0)1709 829511
Individual compartment floor boxOur individual 20A Series ‘Fast Fit’ access floor box has been designed to meet the demands of the modern day working environment. Separate removable compartments allow services to be removed whilst the floor box body and lid remain in situ.
Plug
Spa
ce
Sock
et S
pace
Overall Depth Plug Space Socket Space
85mm 30mm 45mm
100mm 45mm 45mm
115mm 60mm 45mm
130mm 75mm 45mm
Ove
rall
Dep
th
350mm
332mm -0/+3 Cutout
200m
m -
0/+
3 C
utou
t
218m
m
Code Description
One Piece Unwired Floor box, Grey Trim
PP20A385G Standard ‘Fast Fit’ 85mm deep
PP20A310G Standard 'Fast Fit' 100mm deep
PP20A311G Standard 'Fast Fit' 115mm deep
PP20A313G Standard 'Fast Fit' 130mm deep
Individual compartments 45mm deep
PPS2034A Single Width
PPS203D4A Double Width
Add Suffix /KL Additional overcost to fit a Key Lock to a floor box lid
3 Compartment
Code Description
One Piece Unwired Floor box, Grey Trim
PP20A485G Standard ‘Fast Fit’ 85mm deep
PP20A410G Standard 'Fast Fit' 100mm deep
PP20A411G Standard 'Fast Fit' 115mm deep
PP20A413G Standard 'Fast Fit' 130mm deep
Individual compartments 45mm deep
PPS2044A Single Width
PPS204D4A Double Width
Add Suffix /KL Additional overcost to fit a Key Lock to a floor box lid
4 Compartment
• Fast and simple tool free fixing mechanism
• Easy access for carpet fitting: the lid and trim is removed in seconds
• Quick release lid for easy access to accessory plates
• Can be pre-fitted with socket outlet and tap-off unit
• Self closing lid
• Non-Trip cable outlet brackets
• 3 and 4 compartment boxes are the same overall size. Compartment sizes:
� 3 compartment: 100mm x 175mm
� 4 compartment: 75mm x 175mm
• 85mm standard depth (other sizes available, see table opposite)
Deeper options available
www.cmd-ltd.com 106
Individual compartment floor box
Code Description
3m Standard Earth White Plug
P20A385GBS3U104 1 x Twin 13A Switched Socket
P20A385GBS3U202 2 x Twin 13A Switched Sockets
P20A385GBS3U108 1 x Twin 13A Switched RCD Socket
P20A385GBS3U209 2 x Twin 13A Switched RCD Sockets
5m Standard Earth White Plug
P20A385GBS5U103 1 x Twin 13A Switched Socket
P20A385GBS5U202 2 x Twin 13A Switched Sockets
P20A385GBS5U104 1 x Twin 13A Switched RCD Socket
P20A385GBS5U204 2 x Twin 13A Switched RCD Sockets
3 Compartment 4 Compartment
3 Compartment 4 Compartment
3 Compartment 4 Compartment
Standard Earth One piece pre-wired floor box c/w 3m or 5m 32A unfused Betatrak® tap off
Clean Earth One piece pre-wired floor box c/w 3m or 5m 32A unfused Betatrak® tap off
Auxiliary Standard Earth One piece pre-wired floor box c/w 3m or 5m 32A unfused Betatrak® tap off
Code Description
3m Standard Earth White Plug
P20A485GBS3U101 1 x Twin 13A Switched Socket
P20A485GBS3U204 2 x Twin 13A Switched Sockets
P20A485GBS3U103 1 x Twin 13A Switched RCD Socket
P20A485GBS3U206 2 x Twin 13A Switched RCD Sockets
5m Standard Earth White Plug
P20A485GBS5U100 1 x Twin 13A Switched Socket
P20A485GBS5U204 2 x Twin 13A Switched Sockets
P20A485GBS5U101 1 x Twin 13A Switched RCD Socket
P20A485GBS5U205 2 x Twin 13A Switched RCD Sockets
Code Description
3m Clean Earth Red Plug
P20A385GBC3U100 1 x Twin 13A Switched Socket
P20A385GBC3U204 2 x Twin 13A Switched Sockets
P20A385GBC3U103 1 x Twin 13A Switched RCD Socket
P20A385GBC3U206 2 x Twin 13A Switched RCD Sockets
5m Clean Earth Red Plug
P20A385GBC5U101 1 x Twin 13A Switched Socket
P20A385GBC5U201 2 x Twin 13A Switched Sockets
P20A385GBC5U102 1 x Twin 13A Switched RCD Socket
P20A385GBC5U202 2 x Twin 13A Switched RCD Sockets
Code Description
3m Clean Earth Red Plug
P20A485GBC3U100 1 x Twin 13A Switched Socket
P20A485GBC3U202 2 x Twin 13A Switched Sockets
P20A485GBC3U102 1 x Twin 13A Switched RCD Socket
P20A485GBC3U203 2 x Twin 13A Switched RCD Sockets
5m Clean Earth Red Plug
P20A485GBC5U100 1 x Twin 13A Switched Socket
P20A485GBC5U201 2 x Twin 13A Switched Sockets
P20A485GBC5U101 1 x Twin 13A Switched RCD Socket
P20A485GBC5U202 2 x Twin 13A Switched RCD Sockets
Code Description
3m Auxiliary Earth Black Plug
P20A385GBA3U101 1 x Twin 13A Switched Socket
P20A385GBA3U202 2 x Twin 13A Switched Sockets
P20A385GBA3U102 1 x Twin 13A Switched RCD Socket
P20A385GBA3U204 2 x Twin 13A Switched RCD Sockets
5m Auxiliary Earth Black Plug
P20A385GBA5U102 1 x Twin 13A Switched Socket
P20A385GBA5U202 2 x Twin 13A Switched Sockets
P20A385GBA5U103 1 x Twin 13A Switched RCD Socket
P20A385GBA5U203 2 x Twin 13A Switched RCD Sockets
Code Description
3m Auxiliary Earth Black Plug
P20A485GBA3U101 1 x Twin 13A Switched Socket
P20A485GBA3U200 2 x Twin 13A Switched Sockets
P20A485GBA3U102 1 x Twin 13A Switched RCD Socket
P20A485GBA3U201 2 x Twin 13A Switched RCD Sockets
5m Auxiliary Earth Black Plug
P20A485GBA5U100 1 x Twin 13A Switched Socket
P20A485GBA5U200 2 x Twin 13A Switched Sockets
P20A485GBA5U101 1 x Twin 13A Switched RCD Socket
P20A485GBA5U201 2 x Twin 13A Switched RCD Sockets
107sales line: +44 (0)1709 829511
Integral RCD/RCBO floor boxesOur individual 20A Series ‘Fast Fit’ access floor box with integral Din Rail mounted RCD or RCBO protection has been designed to meet the demands of the modern day working environment. By using a modular breaker wired to normal sockets the need for expensive RCD sockets is removed. Separate removable compartments allow services to be removed whilst the floor box body and lid remain in situ.
• Integral RCD/RCBO wired to normal sockets
• Fast and simple tool free fixing mechanism
• Easy access for carpet fitting: the lid and trim is removed in seconds
• Quick release lid for easy access to accessory plates
• Can be pre-fitted with socket outlet and tap off unit
• Self closing lid
• Non-trip cable outlet brackets
Plug
Spa
ce
Sock
et S
pace
Overall Depth Plug Space Socket Space
95mm 30mm 45mm
Ove
rall
Dep
th
350mm
332mm -0/+3 Cutout
200m
m -
0/+
3 C
utou
t
218m
m
Note:
• These boxes are 4 compartment but use the 1st compartment to house the RCD/RCBO.
• Removable compartments are double width for 1 twin socket and triple width for 2 twin sockets.
• Compartment sizes are 75mm x 175mm
www.cmd-ltd.com 108
Integral RCD/RCBO floor boxes
4 Compartment
4 Compartment
4 Compartment
Standard Earth Pre-wired floor box c/w 32A unfused Betatrak® tap off
Clean Earth Pre-wired floor box c/w 32A unfused Betatrak® tap off
Auxiliary Standard Earth Pre-wired floor box c/w 32A unfused Betatrak® tap off
Code Description RCD/RCBO
3m Standard Earth White Plug
P20A495GBS3U200 1 x Twin 13A Switched Socket 40A RCD
P20A495GBS3U308 2 x Twin 13A Switched Sockets 40A RCD
P20A495GBS3U207 1 x Twin 13A Switched Socket 20A RCBO
P20A495GBS3U301 2 x Twin 13A Switched Sockets 20A RCBO
5m Standard Earth White Plug
P20A495GBS5U204 1 x Twin 13A Switched Socket 40A RCD
P20A495GBS5U305 2 x Twin 13A Switched Sockets 40A RCD
P20A495GBS5U203 1 x Twin 13A Switched Socket 20A RCBO
P20A495GBS5U304 2 x Twin 13A Switched Sockets 20A RCBO
Code Description RCD/RCBO
3m Clean Earth Red Plug
P20A495GBC3U202 1 x Twin 13A Switched Socket 40A RCD
P20A495GBC3U302 2 x Twin 13A Switched Sockets 40A RCD
P20A495GBC3U203 1 x Twin 13A Switched Socket 20A RCBO
P20A495GBC3U303 2 x Twin 13A Switched Sockets 20A RCBO
5m Clean Earth Red Plug
P20A495GBC5U201 1 x Twin 13A Switched Socket 40A RCD
P20A495GBC5U301 2 x Twin 13A Switched Sockets 40A RCD
P20A495GBC5U202 1 x Twin 13A Switched Socket 20A RCBO
P20A495GBC5U302 2 x Twin 13A Switched Sockets 20A RCBO
Code Description RCD/RCBO
3m Auxiliary Earth Black Plug
P20A495GBA3U200 1 x Twin 13A Switched Socket 40A RCD
P20A495GBA3U300 2 x Twin 13A Switched Sockets 40A RCD
P20A495GBA3U201 1 x Twin 13A Switched Socket 20A RCBO
P20A495GBA3U301 2 x Twin 13A Switched Sockets 20A RCBO
5m Auxiliary Earth Black Plug
P20A495GBA5U200 1 x Twin 13A Switched Socket 40A RCD
P20A495GBA5U300 2 x Twin 13A Switched Sockets 40A RCD
P20A495GBA5U201 1 x Twin 13A Switched Socket 20A RCBO
P20A495GBA5U301 2 x Twin 13A Switched Sockets 20A RCBO
109sales line: +44 (0)1709 829511
1 compartment slab box with optional fixing feet can be used along with our range of floor grommets when budget control is top priority. The overall size of the unit is 175 x 75 x 40mm deep. The box base has a 20mm knock-out to allow conduit access and is manufactured from galvanised steel.
175 mm
75 m
m
1 compartment slab box
0.9mm galvanised steel
Code Description
1 Compartment Slab Boxes
PPS9014OS 75mm wide slab box c/w fixing feet
Standard Wired Configurations
Standard Earth
PPA7097/1 Slab Box c/w fixing feet, Twin Socket, 3m Tap off 32A Unfused Standard Earth
PPA7097/5 Slab Box c/w fixing feet, Twin Socket, 5m Tap off 32A Unfused Standard Earth
Clean Earth
PPA7097/3 Slab Box c/w fixing feet, Twin Socket, 3m Tap off 32A Unfused Clean Earth
PPA7097/6 Slab Box c/w fixing feet, Twin Socket, 5m Tap off 32A Unfused Clean Earth
Auxiliary Earth
PPA7097/12 Slab Box c/w fixing feet, Twin Socket, 3m Tap off 32A Unfused Auxiliary Earth
PPA7097/13 Slab Box c/w fixing feet, Twin Socket, 5m Tap off 32A Unfused Auxiliary Earth
www.cmd-ltd.com 110
2 compartment slab box2 compartment slab box, with retractable fixing feet, that can be used along with our range of floor grommets when budget control is top priority. The overall size of the unit is 182 x 200 x 60mm deep. The box base has 20mm and 25mm conduit knockouts in each short side and dividing fillets are provided to separate services. The box base is manufactured from galvanised steel.
Retractable fixing brackets
0.9mm galvanised
steel
200
mm
182 mm
Code Description
2 Compartment Slab Boxes
PPS2325OS 2 Compartment 60mm deep slab box c/w retractable fixing feet
Standard Wired Configurations
Standard Earth
P2325OS/BS3U100 Slab Box c/w fixing feet, Twin Socket, 3m Tap off 32A Unfused Standard Earth
P2325OS/BS3U200 Slab Box c/w fixing feet, 2x Twin Sockets, 3m Tap off 32A Unfused Standard Earth
P2325OS/BS5U100 Slab Box c/w fixing feet, Twin Socket, 5m Tap off 32A Unfused Standard Earth
P2325OS/BS5U200 Slab Box c/w fixing feet, 2x Twin Sockets, 5m Tap off 32A Unfused Standard Earth
Clean Earth
P2325OS/BC3U100 Slab Box c/w fixing feet, Twin Socket, 3m Tap off 32A Unfused Clean Earth
P2325OS/BC3U200 Slab Box c/w fixing feet, 2x Twin Sockets, 3m Tap off 32A Unfused Clean Earth
P2325OS/BC5U100 Slab Box c/w fixing feet, Twin Socket, 5m Tap off 32A Unfused Clean Earth
P2325OS/BC5U200 Slab Box c/w fixing feet, 2x Twin Sockets, 5m Tap off 32A Unfused Clean Earth
Auxiliary Earth
P2325OS/BA3U100 Slab Box c/w fixing feet, Twin Socket, 3m Tap off 32A Unfused Auxiliary Earth
P2325OS/BA3U200 Slab Box c/w fixing feet, 2x Twin Sockets, 3m Tap off 32A Unfused Auxiliary Earth
P2325OS/BA5U100 Slab Box c/w fixing feet, Twin Socket, 5m Tap off 32A Unfused Auxiliary Earth
P2325OS/BA5U200 Slab Box c/w fixing feet, 2x Twin Sockets, 5m Tap off 32A Unfused Auxiliary Earth
20/25mm entry knockouts
111sales line: +44 (0)1709 829511
3 compartment slab box3 compartment slab box, with retractable fixing feet, that can be used along with our range of floor grommets when budget control is top priority. The overall size of the unit is 332 x 200 x 60mm deep. The box base has 20mm and 25mm conduit knockouts in each long side and dividing fillets are provided to separate services. The box base is manufactured from galvanised steel.
Code Description
3 Compartment Slab Boxes
PPS2335OS 3 Compartment 60mm deep slab box c/w retractable fixing feet
Standard Wired Configurations (add on required data plates)
Standard Earth
P2335OS/BS3U100 Slab Box c/w fixing feet, Twin Socket, 3m Tap off 32A Unfused Standard Earth
P2335OS/BS3U200 Slab Box c/w fixing feet, 2x Twin Sockets, 3m Tap off 32A Unfused Standard Earth
P2335OS/BS5U100 Slab Box c/w fixing feet, Twin Socket, 5m Tap off 32A Unfused Standard Earth
P2335OS/BS5U200 Slab Box c/w fixing feet, 2x Twin Sockets, 5m Tap off 32A Unfused Standard Earth
Clean Earth
P2335OS/BC3U100 Slab Box c/w fixing feet, Twin Socket, 3m Tap off 32A Unfused Clean Earth
P2335OS/BC3U200 Slab Box c/w fixing feet, 2x Twin Sockets, 3m Tap off 32A Unfused Clean Earth
P2335OS/BC5U100 Slab Box c/w fixing feet, Twin Socket, 5m Tap off 32A Unfused Clean Earth
P2335OS/BC5U200 Slab Box c/w fixing feet, 2x Twin Sockets, 5m Tap off 32A Unfused Clean Earth
Auxiliary Earth
P2335OS/BA3U100 Slab Box c/w fixing feet, Twin Socket, 3m Tap off 32A Unfused Auxiliary Earth
P2335OS/BA3U200 Slab Box c/w fixing feet, 2x Twin Sockets, 3m Tap off 32A Unfused Auxiliary Earth
P2335OS/BA5U100 Slab Box c/w fixing feet, Twin Socket, 5m Tap off 32A Unfused Auxiliary Earth
P2335OS/BA5U200 Slab Box c/w fixing feet, 2x Twin Sockets, 5m Tap off 32A Unfused Auxiliary Earth
200m
m
332mm
Retractable fixing brackets
0.9mm galvanised
steel
20/25mm entry knockouts
www.cmd-ltd.com 112
4 compartment slab box4 compartment slab box, with retractable fixing feet, that can be used along with our range of floor grommets when budget control is top priority. The overall size of the unit is 332 x 200 x 60mm deep. The box base has 20mm and 25mm conduit knockouts in each long side and dividing fillets are provided to separate services. The box base is manufactured from galvanised steel.
Code Description
4 Compartment Slab Boxes
PPS2345OS 4 Compartment 60mm deep slab box c/w retractable fixing feet
Standard Wired Configurations (add on required data plates)
Standard Earth
P2345OS/BS3U100 Slab Box c/w fixing feet, Twin Socket, 3m Tap off 32A Unfused Standard Earth
P2345OS/BS3U200 Slab Box c/w fixing feet, 2x Twin Sockets, 3m Tap off 32A Unfused Standard Earth
P2345OS/BS5U100 Slab Box c/w fixing feet, Twin Socket, 5m Tap off 32A Unfused Standard Earth
P2345OS/BS5U200 Slab Box c/w fixing feet, 2x Twin Sockets, 5m Tap off 32A Unfused Standard Earth
Clean Earth
P2345OS/BC3U100 Slab Box c/w fixing feet, Twin Socket, 3m Tap off 32A Unfused Clean Earth
P2345OS/BC3U200 Slab Box c/w fixing feet, 2x Twin Sockets, 3m Tap off 32A Unfused Clean Earth
P2345OS/BC5U100 Slab Box c/w fixing feet, Twin Socket, 5m Tap off 32A Unfused Clean Earth
P2345OS/BC5U200 Slab Box c/w fixing feet, 2x Twin Sockets, 5m Tap off 32A Unfused Clean Earth
Auxiliary Earth
P2345OS/BA3U100 Slab Box c/w fixing feet, Twin Socket, 3m Tap off 32A Unfused Auxiliary Earth
P2345OS/BA3U200 Slab Box c/w fixing feet, 2x Twin Sockets, 3m Tap off 32A Unfused Auxiliary Earth
P2345OS/BA5U100 Slab Box c/w fixing feet, Twin Socket, 5m Tap off 32A Unfused Auxiliary Earth
P2345OS/BA5U200 Slab Box c/w fixing feet, 2x Twin Sockets, 5m Tap off 32A Unfused Auxiliary Earth
200m
m
332mm
Retractable fixing brackets
0.9mm galvanised
steel
20/25mm entry knockouts
113sales line: +44 (0)1709 829511
The 93 and 99 Series range of floor boxes are available for use as either a ‘stand alone’ screed floor type or a screw fixed type suitable for raised floors. Screed floor types are supplied with jacking legs which allow 10mm adjustment for levelling with the finished floor depth and also have taped seams to prevent ingress of screed.
• Quick release lid for easy access to accessory plate
• Self closing lid
• Non-Trip cable outlet brackets
Screed + screwfix floor boxes
Code Description
PP93275G Screw Fix, 75mm deep Floor box, Grey Trim
PPS93275G Screed Box, 75mm deep, Grey Trim - Adapted for Screed
Self closing lid20/25mm
entry knockoutsCable protectors
Code Description
PP99375G Screw Fix, 75mm deep Floor box, Grey Trim
PPS99375G Screed Box, 75mm deep, Grey Trim - Adapted for Screed
Code Description
PP99475G Screw Fix, 75mm deep Floor box, Grey Trim
PPS99475G Screed Box, 75mm deep, Grey Trim - Adapted for Screed
Add Suffix /KL
Additional overcost to fit a Key Lock to a floor box lid
93 Series 2 compartment 99 Series 3 compartment 99 Series 4 compartment
200m
m -
0/+
3 C
ut O
ut
212m
m
200m
m -
0/+
3 C
ut O
ut
218m
m
200m
m -
0/+
3 C
ut O
ut
218m
m
183mm -0/+3 Cut Out195mm
332mm -0/+3 Cut Out350mm
332mm -0/+3 Cut Out350mm
www.cmd-ltd.com 114
Screed stainless steel floor boxes3 or 4 compartment stainless steel access floor box comprises of three distinct assemblies: the box base, the mounting frame and purpose made stainless steel frame/lid assembly. The box base has 20mm and 25mm conduit knockouts in each long side and dividing fillets that are provided to separate services. The box base is manufactured from galvanised steel and comes complete with a grid to accept interchangeable accessories.
The mounting frame is manufactured from galvanised steel and has two fixing holes in each long side. The frame/lid tray assembly is manufactured from brushed stainless steel with straight edges and cable outlet brackets in the same material. The recess in the tray lid is 23mm deep. Maximum outside size of S/S trim is 325mm x 193mm and overall box depth is 99mm. The box is provided with jacking legs for levelling and adjustment – Screed option only.
193m
m
325mm
cable outer frame
stainless steel tray lid
stainless steelsegregator frame
chrome ring pull (x2) supplied by CMD
for fitting by floor contractor
approx 30mm plugtop space due to final
lid adjustment
329.5mm levelling screws
99.5
mm
76.5
mm
spacer
accessory plate
20mm stone
3mm bedding
Code Description
Screed and Screwfix Unwired Floor box,Stainless Steel Trim
PP90375SS/23 Screw fix 75mm deep
PPS90375SS/23 Screed 75mm deep
3 Compartment
Code Description
Screed and Screwfix Unwired Floor box, Stainless Steel Trim
PP90475SS/23 Screw fix 75mm deep
PPS90475SS/23 Screed 75mm deep
4 Compartment
115sales line: +44 (0)1709 829511
Select from our wide range of serviced power and unserviced data options. Accessory plates are common to most ranges - one piece, individual, screed and stainless floor boxes and slab floor boxes.All accessory plates are finished in light grey paint (RAL 7035).
Plate sizes - 100mm x 175mm. Can only be fitted in 3 compartment floor and slab boxes.
1 twin RCD socket
Code Description
PP3291 3 Compartment Version
1 twin 13A switched socket
Code Description
PCP301 3 Compartment Version
1 twin 13A unswitched socket
Code Description
PCP302 3 Compartment Version
3 single 13A unswitched socket
Code Description
PCP3003 3 Compartment Version
Plate pierced to accept 4 x LJ6C/RJ45 (Piercings 37.0 x 22.3)
Code Description
PV304 3 Compartment Version
Plate to accept 2 x LJ2 telephone outlets (Units 68mm Square)
Code Description
PV305 3 Compartment Version
Standard BS 1363 2 gang piercing
Code Description
PM307 3 Compartment Version
Plate to accept 2 x standard 1 gang fittings (Units 86mm Square)
Code Description
PV311 3 Compartment Version
Plate pierced to accept 6 x LJ6C/RJ45 (Piercings 37.0 x 22.3)
Code Description
PV342 3 Compartment Version
Angled plate pierced to accept 4 x LJ6C/RJ45 (Piercing 37.0 x 22.3)
Code Description
PDV3301 3 Compartment Version
Plate pierced to accept 4 x RW Data/ Alphasnap Units (Piercings
48.0 x 23.5)
Code Description
PD3107 3 Compartment Version
Plate pierced to accept 2 x Euro (50mm x 50mm) Adapter Collars
Code Description
PD331 3 Compartment Version
3 compartment plates
www.cmd-ltd.com 116
Code Description
PP3291 Twin RCD Socket
PCP301 Twin Switched Socket Outlet
PCP302 Twin Unswitched Socket Outlet
PCP3003 Triple Unswitched Socket Outlet
PV304 4 No. RJ45 (37.1 x 22.3)
PV305 Plate pierced to accept 2 - LJ2
PM307 Plate pierced to accept 1 No. 2- Gang Std BS1363 outlet
PV311 Plate pierced to accept 2 No. 1- Gang Std BS1363 outlet
PV342 6 No. RJ45 (37.1 x 22.3)
PD3342 4 No. Angled RJ45
PD3107 4 No. R W Data RJ45 (47.0 x 23.5)
PD331 Plate pierced to accept 2 - Euromod Collars (not supplied)
PCP301C Clean Earth Twin Switched Socket Outlet
PCP302C Clean Earth Twin Unswitched Socket Outlet
PCP3003C Clean Earth Triple Unswitched Socket Outlet
PP301N Twin Switched Socket Outlet Non-Std - Wandsworth
PP3424 Twin Unswitched 5A socket outlet
PB306 Blank Plate
PV388 8 No. RJ45 (37.1 x 22.3)
PX3210 White LJU6C size blank data cover
3 compartment plates
Blank plate
Code Description
PB306 3 Compartment Version
117sales line: +44 (0)1709 829511
Select from our wide range of serviced power and unserviced data options, 4 compartment range for one piece, individual, screed & stainless floor boxes & slab boxes 75mm wide. Can be fitted in 1, 2 and 4 compartment slab boxes and 2, 4 compartment floor boxes. All accessory plates are finished in light grey paint (RAL 7035).
Plate sizes - 75mm x 175mm.
Sockets are available in clean earth versions. All twin sockets have a dual earth facility to enable compliance to BS 7671:2008 Amd 3 Regulation 543.7.1.4. If the accessory plate you require is not included in the most widely used selection as shown, please ring technical sales for further information.
NB. 3 & 4 compartment accessory plates cannot be mixed in boxes
1 twin RCD socket
Code Description
PP4291 4 Compartment Version
1 twin 13A switched socket
Code Description
PCP401 4 Compartment Version
1 twin 13A unswitched socket
Code Description
PCP402 4 Compartment Version
3 single 13A unswitched socket
Code Description
PCP403 4 Compartment Version
Plate pierced to accept 4 x LJ6C/RJ45 (Piercings 37.0 x 22.3)
Code Description
PV404 4 Compartment Version
Plate to accept 2 x LJ2 telephone outlets (Units 68mm Square)
Code Description
PV405 4 Compartment Version
Blank plate
Code Description
PB406 4 Compartment Version
Plate pierced to accept 6 x LJ6C/RJ45 (Piercings 37.0 x 22.3)
Code Description
PV442 4 Compartment Version
Angled plate pierced to accept 4 x LJ6C/RJ45 (Piercing 37.0 x 22.3)
Code Description
PDV4301 4 Compartment Version
Plate pierced to accept 4 x RW Data/Alphasnap Units (Piercings
48.0 x 23.5)
Code Description
PD4107 4 Compartment Version
Plate pierced to accept 2 x Euro (50mm x 50mm) Adapter Collars
Code Description
PD431 4 Compartment Version
4 compartment plates
www.cmd-ltd.com 118
4 compartment plates
Code Description
PP4291 Twin RCD Socket
PCP401 Twin Switched Socket Outlet
PCP402 Twin Unswitched Socket Outlet
PCP403 Triple Unswitched Socket Outlet
PV404 4 No. RJ45 (37.1 x 22.3)
PV405 Plate pierced to accept 2 - LJ2
PB406 Blank Plate
PV442 6 No. RJ45 (37.1 x 22.3)
PD4342 4 No. Angled RJ45
PD4107 4 No. R W Data RJ45 (47.0 x 23.5)
PD431 2 No. Euro Adaptor collars (50 x 50)
PCP401C Clean Earth Twin Switched Socket Outlet
PCP402C Clean Earth Twin Unswitched Socket Outlet
PV4004 4 No. RJ45 in line (37.1 x 22.3)
PX3210 White LJU6C size blank data cover
119sales line: +44 (0)1709 829511
Cable hives are an alternative to floor boxes & slab boxes for taking underfloor power to under desk level. They offer an ideal solution for a fast, simple and unobtrusive installation. Easy to install and relocate if necessary, cable hives are ideal for use with our Conti power module, perfect for any office power requirements.
• Installed in less than 5 seconds – removed in less than 10 seconds (No tools required for fitting)
• Available in127mm and 210mm (Outside diameter: 140mm and 225mm respectively)
• Quality, reliability and safety come as standard
• Self closing lifting handles
• Manufactured from polycarbonate – ABS in standard grey (RAL 7031)
• Fasteners will work on panel thickness of 5mm and upwards
• Panel cut out diameter: 127mm and 210mm
Cable Hives®
Split lid option - Integral foam insert
for secure cable gripAccessible lid with retention cable
Hive colour - Polycarbonate ABS
Grey - RAL 7031, (other colours
available, minimum quantity
requirements)
Lid Variations: Accepts up to
2 x 40mm flexible conduits
Soft & hard foam available
Interlocking clamp top
Maximum number of conduits accepted when lid is in place:
Standard Cable Hive (127mm)
PPH261G (Hard Foam) PPHC261G (Soft Foam)
4 x 16mm 8 x 16mm
3 x 20mm 3 x 20mm
2 x 25mm 3 x 25mm
1 x 32mm 2 x 32mm
Simple access:
‘Push fit’ for fast installation
Unique self latching mechanism
Large Cable Hive (210mm)
PPG211G (Hard Foam) PPGC211G (Soft Foam)
10 x 16mm 16 x 16mm
6 x 20mm 9 x 20mm
3 x 25mm 5 x 25mm
3 x 32mm 3 x 32mm
Available in 2 sizes with
127mm & 210mm cutout
diameters
www.cmd-ltd.com 120
Our angled standard RCD Cleaners Hive has been designed to allow the fitment of moulded 13A plug tops with strain relief without stressing the flex hence its new angled design. Designed to power 230V vacuum cleaners.
Features:
• More robust• 35mm reduction in overall depth• Improved user functionality
Angled standard RCD cleaners hive
Reversible centre lid - 6mm carpet cut for improved installation aesthetics
Centre lid retainer - for added security. Eliminates lid loss
Hive colour - Grey, RAL7031
(other colours available)
Power sockets - Provide strain relief clearance for moulded plugs
Cable Hives®
121sales line: +44 (0)1709 829511
Large Cable Hive
Large Power Hive
Large Data Hive
Large Power & Data Hive
Cable Hives®
Lid Body Cable Hive Complete
Lid Body Power Hive Complete2 x 13A Switched Sockets
Lid Body Data Hive Complete4 x RJ45 cut-outs
Lid BodyPower/Data Hive
Complete2 x 13A switched,4 x RJ45 cut-outs
Code Height Description
PPG211G 40mm Large Cable Hive
Code Height Description
PPG212G 107mm Large Power Cable Hive 2x Socket
PPG212G/RCD 107mm RCD Large Power Cable Hive 2x Sockets
Code Height Description
PPG214G 107mm Large Data Hive c/w data box 4 x RJ45
Code Height Description
PPG215G 107mm Large Power/Data Hive 2x Socket & 4x RJ45
PPG215G/RCD 107mm Large Power/Data Hive 2x Socket (RCD) & 4x RJ45
Please note that the cut out size for our large cable hives is 210mm diameter.
www.cmd-ltd.com 122
Code Height Description
PPH263G 76mm Standard Cleaners Hive
PPH263G/SW 105mm Cleaners Hive (Switched Plastic Moulded Socket)
PPH263G/5M 120mm Cleaners Hive (Angled 5A Unswitched moulded socket)
PPH263NG 76mm Cleaners Hive (Non Standard Unswitched Socket)
PPH263G/RCD/A 120mm Angled Standard RCD Cleaners Hive
Standard Cleaners Hive
Standard Power/Data Hive
Standard Access Hive
Cable Hives®
Lid Body Cleaners Hive Complete13A Socket
Lid Body
Lid Body Access Hive Complete
13A Socket Hive Complete2 x RJ45 Cut-Outs
Code Height Description
PPH265G 93mm Standard Power Cable Hive
PDH265G/245 93mm Standard 2 Way Data Hive
Code Height Description
PPH264G 40mm Standard Access Cable Hive
Please note that the cut out size for our standard cable hives is 127mm diameter.
Standard Cable Hive
Lid Body Cable Hive Complete
Code Height Description
PPH261G 40mm Standard Cable Hive
Cable Tidy Fixing
Code Height Description
PPH22260G 93mm Cable Tidy fixing for use with Standard Cable Hive
Fixing bracket Fitted to Hive lidComplete with Cable Tidy
or
123sales line: +44 (0)1709 829511
81mm aperture
101mm aperture
140mm
38mm
• ‘Fast-Fit’ installation from floor tile fixing to cable deployment
• Allows simple access for services underfloor to workstations of all kinds
• UL 94 VO Flame class rating
• Integral carpet gripper spikes
• Floor service unit conforms to IEC-61534-22
127mm
38mm
The grommet can simply be secured by pushing down into position
Can accommodate all cable types or 3 metal conduits up to a 25mm diameter or 4 x 20mm diameter
Manufactured from hard wearing durable flame retardant PC/ABS in Grey as standard (alternative colours available as special order)
Maximum number of conduits accepted when lid is in place.
Standard cable grommet (127mm)
Accommodates
all cable types
PC/ABS
(Grey as standard)
Push down - fast fixing
Standard cable grommet (127mm)
PCFG235G
8 x 16mm
4 x 20mm
3 x 25mm
2 x 32mm
Code Description
PCFG235G 127mm Grommet
www.cmd-ltd.com 124
132mm
190mm aperture
230mm
42mm
210mm
40mm
• ‘Fast-Fit’ installation from floor tile fixing to cable deployment
• Allows simple access for services underfloor to workstations of all kinds
• UL 94 VO Flame class rating
• Floor service unit conforms to IEC-61534-22
• Recommended for installation in light traffic areas
• Integral carpet gripper spikes
The grommet can simply be secured by pushing down into position
Can accommodate all cable types or 5 metal conduits up to a 25mm diameter or 8 x 20mm diameter
Manufactured from hard wearing durable flame retardant PC/ABS in Grey as standard (alternative colours available as special order)
Large cable grommet (210mm)
Accommodates
all cable types
PC/ABS
(Grey as standard)
Push down - fast fixing
Large cable grommet (210mm)
PCFG238G
12 x 16mm
8 x 20mm
4 x 25mm
3 x 32mm
Maximum number of conduits accepted when lid is in place.
Code Description
PCFG238G 210mm Grommet
125sales line: +44 (0)1709 829511
Black Box™ DistributionFeatures:
• Compact aesthetic modular Power Distribution Unit (PDU) for the distribution of power within office furniture installations
• Requires a separate connecting mains supply
• Incoming circuit protection device options by either a 32A RCD (overload protection up stream) or 32A RCBO
• Up to 8 outgoing circuits, individually protected by 6, 10 or 16 amp MCBs, available in 4, 6 or 8 module variations
• Outgoing circuit connected from the PDU by Wieland GST18 connectors in either 3 pole (Standard Earth) or 4 pole (Clean Earth)
• All MCBs are accessible through a clear hinged cover which has the option of being lockable or accessible by the use of a tool only
• Stylish design, ideal for commercial offices, health care and education projects where the PDU may be sited in publicly accessible areas
• Products are CE Marked conforming to the requirements of BS 5733
Black Box™ distribution
Code Description
PDU8RCBO3P/16GST Power distribution box / 8 x Wieland outputs (Standard Earth) 1 x RCBO / 8 x 16A MCBs
PDU6RCBO3P/16GST Power distribution box / 6 x Wieland outputs (Standard Earth) 1 x RCBO / 6 x 16A MCBs
PDU4RCBO3P/16GST Power distribution box / 4 x Wieland outputs (Standard Earth) 1 x RCBO / 4 x 16A MCBs
PDU8RCD3P/16GST Power distribution box / 8 x Wieland outputs (Standard Earth) 1 x RCD / 8 x 16A MCBs
PDU6RCD3P/16GST Power distribution box / 6 x Wieland outputs (Standard Earth) 1 x RCD / 6 x 16A MCBs
PDU4RCD3P/16GST Power distribution box / 4x Wieland outputs (Standard Earth) 1 x RCD / 4 x 16A MCBs
PDU8RCBO4P/16GST Power distribution box / 8 x Wieland outputs (Clean Earth) 1 x RCBO / 8 x 16A MCBs
PDU6RCBO4P/16GST Power distribution box / 6 x Wieland outputs (Clean Earth) 1 x RCBO / 6 x 16A MCBs
PDU4RCBO4P/16GST Power distribution box / 4 x Wieland outputs (Clean Earth) 1 x RCBO / 4 x 16A MCBs
PDU8RCD4P/16GST 16 Power distribution box / 8 x Wieland outputs (Clean Earth) 1 x RCD / 8 x 16A MCBs
PDU6RCD4P/16GST 16 Power distribution box / 6 x Wieland outputs (Clean Earth) 1 x RCD / 6 x 16A MCBs
PDU4RCD4P/16GST 16 Power distribution box / 4 x Wieland outputs (Clean Earth) 1 x RCD / 4 x 16A MCBs
www.cmd-ltd.com 126
Black Box™ distribution
20mm
Black Box™ can be mounted vertically or horizontally, to any wall or surface.
Black Box™ can be manufactured to house 4, 6 or 8 Wieland sockets with individual protection.
Neutrik socket
Transparent cover
MCB(6, 10 or 16 amp)
Stylish black case
Wieland outlets
Screw fixing holes
Incoming circuitprotection
270mm230mm
330mm
80m
m
100m
m
290mm
230mm190mm
200mmfig 1.
fig 2.
fig 3.
127sales line: +44 (0)1709 829511
Compatible with our
lighting control systems
Aluminium housing
4 & 6 pole versions with tap offs on one side
Retaining spring on all
tap offs
Multi pole tap off
Degree of protection up to IP55
Ceiling bracket is available
25A lighting busbarOur 25A range of lighting busbar is used mainly for overhead installation as it is suitable for all types of commercial & industrial lighting making it ideal for use in retail stores, offices and hotels due to its flexibility in creating specific lighting designs. The aluminium-clad trunking is available in 4 and 6 pole configuration with tap off positions every metre along a standard 3m length. Simple to install, with no requirement for bolting lengths together, the range also incorporates a flexible corner to accommodate changes in height or direction.
General Construction - Strong extruded aluminium housing with rigid copper conductorsEnclose - Degree of protection to BS EN 60529 (IEC 60529); IP41 Standard; IP55 available on requestConductor Bars - Four and Six copper conductors (Protective earth conductor provided by the housing)Insulation - Tap off points are marked on the 25A lighting busbar with moulded internal polyester supporting the individual busbars - classified flammability grade UL-94 V-O
Reinforcement bracket is available
L1 L2 L3 N L1 L2 L3 N L4L5
40A Busbar 4P+PE 40A Busbar 6P+PE
www.cmd-ltd.com 128
25A lighting busbar
25A Lighting Busbar Range
Code Description Weight Length Rating Outlets
PNBA25A106 25A 6P+PE 1m 3-Phase or 3-Phase/DALI Lighting Busbar 0.7kg 1m 25A 1
PNBA25A30 25A 4P+PE 3m 3-Phase Lighting Busbar 1.65kg 3m 25A 3
PNBA25A306 25A 6P+PE 3m 3-Phase and DALI Lighting Busbar 2.1kg 3m 25A 3
PNATSX25A 25A 4P+PE 3-Phase Left Hand End Feed 0.22kg 0.235m 25A N/A
PNATDX25A 25A 4P+PE 3-Phase Right Hand End Feed 0.38kg 0.235m 25A N/A
PNATSX25A6 25A 6P+PE 3-Phase and DALI Left Hand End Feed 0.538kg 0.365m 25A N/A
PNATDX25A6 25A 6P+PE 3-Phase and DALI Right Hand End Feed 0.85kg 0.365m 25A N/A
PNFLX25A4P0.5 25A 4 Pole 0.5M Flexible Corner Kit* 0.786kg 0.5m 25A N/A
PNFLX25A6P0.5 25A 6 Pole 0.5M Flexible Corner Kit* 0.85kg 0.5m 25A N/A
End Feed Flexible Corner Kit Tap Off Rubber Joint Cover
Rubber End Cap Contact Carriers Light Fitting Bracket Wall/Ceiling Bracket
25A Lighting Busbars Accessories (Common to all lighting busbars)
Code Description
PNSFIPN Unwired 6A Fused 4 Pole Tap Off Phase Selectable c/w 2 contacts
PNSBM6A Unwired 6A Fused 6 Pole Tap Off Phase Selectable c/w 2 contacts
PNSBM16A Unwired 16A Fused 6 Pole Tap Off Phase Selectable c/w 2 contacts
PNCTIP55 IP55 Rubber End Cap for Left Hand Feeds
PNCTIP55DX IP55 Rubber End Cap for Right Hand Feeds
PNGRIP55 IP55 Rubber Joint Cover
PNGRFP Busbar Joint Reinforcement Sleeve
PNCMCF 6.3A Fused Contact Carrier for 6A Tap Offs
PNCMCF16 16A Fused Contact Carrier for 16A Tap Offs
PNCMSF16 16A UnFused Contact Carrier for 16A Tap Offs
PNSTCWB Wall/Ceiling Steel Universal Bracket
PNSTCI Light Fitting Steel Bracket - 12Kg Max
PNSTLN Light Fitting Steel Bracket - 20Kg Max
*Supplied in kit form, which requires assembly
129sales line: +44 (0)1709 829511
Aluminium housing
4 & 6 pole versions with tap offs on one side
Retaining spring on all
tap offs
Multi pole tap off
Degree of protection up to IP55
Ceiling bracket is available
Reinforcement bracket is available
40A lighting busbar
L1 L2 L3 N L1 L2 L3 N L4L5
Our 40A range of lighting busbar is used mainly for overhead installation as it is suitable for all types of commercial & industrial lighting making it ideal for use in retail stores, offices and hotels due to its flexibility in creating specific lighting designs. The aluminium-clad trunking is available in 4 and 6 pole configuration with tap off positions every metre along a standard 3m length. Simple to install, with no requirement for bolting lengths together, the range also incorporates a flexible corner to accommodate changes in height or direction.
General Construction - Strong extruded aluminium housing with rigig copper conductorsEnclose - Degree of protection to BS EN 60529 (IEC 60529); IP41 Standard; IP55 available on requestConductor Bars - Four and Six copper conductors (Protective earth conductor provided by the housing)Insulation - Tap off points are marked on the 40A lighting busbar with moulded internal polyester supporting the individual busbars - classified flammability grade UL-94 V-O
40A Busbar 4P+PE 40A Busbar 6P+PE
L1 N2 L2N1
40A Busbar Dual Circuit 4P+PE
Compatible with our
lighting control systems
www.cmd-ltd.com 130
40A lighting busbar
40A Lighting Busbar Range
40A Lighting Busbars Accessories (Common to all lighting busbars)
End Feed Flexible Corner Kit Tap Off Rubber Joint Cover
Rubber End Cap
Code Description
PNSFIPN Unwired 6A Fused 4 Pole Tap Off Phase Selectable c/w 2 contacts
PNSBM6A Unwired 6A Fused 6 Pole Tap Off Phase Selectable c/w 2 contacts
PNSBM16A Unwired 16A Fused 6 Pole Tap Off Phase Selectable c/w 2 contacts
PNCTIP55 IP55 Rubber End Cap for Left Hand Feeds
PNCTIP55DX IP55 Rubber End Cap for Right Hand Feeds
PNGRIP55 IP55 Rubber Joint Cover
PNGRFP Busbar Joint Reinforcement Sleeve
PNCMCF 6.3A Fused Contact Carrier for 6A Tap Offs
PNCMCF16 16A Fused Contact Carrier for 16A Tap Offs
PNCMSF16 16A UnFused Contact Carrier for 16A Tap Offs
PNSTCWB Wall/Ceiling Steel Universal Bracket
PNSTCI Light Fitting Steel Bracket - 12Kg Max
PNSTLN Light Fitting Steel Bracket - 20Kg Max
Contact Carriers Light Fitting Bracket Wall/Ceiling Bracket
Code Description Weight Length Rating Outlets
PNBA40A106 40A 6P+PE 1m 3-Phase or 3-Phase and DALI Lighting Busbar 0.8kg 1m 40A 1
PNBA40A10S2C 40A 4P+PE 1m Dual Circuit Lighting Busbar 0.7kg 3m 40A 3
PNBA40A30 40A 4P+PE 3m 3-Phase Lighting Busbar 2.1kg 3m 40A 3
PNBA40A30S2C 40A 4P+PE 3m Dual Circuit Lighting Busbar 2.1kg 3m 40A 5
PNBA40A306 40A 6P+PE 3m 3-Phase and DALI Lighting Busbar 2.4kg 3m 40A 3
PNATSX40A6 40A 6P+PE 3-Phase or 3-Phase and DALI Left Hand End Feed 0.606kg 0.365m 40A N/A
PNATDX40A6 40A 6P+PE 3-Phase or 3-Phase and DALI Right Hand End Feed 0.58kg 0.365m 40A N/A
PNATSX40A6S2C 40A 6P+PE Dual Circuit Left Hand End Feed 0.606kg 0.34m 40A N/A
PNATDX40A6S2C 40A 6P+PE Dual Circuit Right Hand End Feed 0.58kg 0.34m 40A N/A
PNFLX40A4P0.5 40A 4 Pole 0.5M Flexible Corner Kit* 2.2kg 0.5m 40A N/A
PNFLX40A6P0.5 40A 6 Pole 0.5M Flexible Corner Kit* 2.25kg 0.5m 40A N/A
*Supplied in kit form, which requires assembly
131sales line: +44 (0)1709 829511
Technical dataConformity IEC 439-2 EN 60439-2
25A 4 Pole 3m
25A 6 Pole 3m
25A 6 Pole 1m
40A 4 Pole 3m
40A 6 Pole 3m
40A 6 Pole 1m
Live conductors 4 6 6 4 6 6
Weight kg 1.55 1.65 0.7 2.1 2.5 0.9
Standard number of sockets3 (5 if dual)
3 13 (5 if dual)
3 1
Standard socket spacing mm 1000 1000 n/a 1000 1000 n/a
Non-standard number of sockets (Quantity dependant) 5/10 5/10 1 5/10 5/10 1
Housing thickness mm 0.8 0.8 0.8 0.8 0.8 0.8
Rate current In [A] 25 25 25 40 40 40
Frequency f [Hz] 50/60 50/60 50/60 50/60 50/60 50/60
Rated insulation voltage Ui [V] 660 660 660 660 660 660
Rated operation voltage Ue [V] 230/400 230/400 230/400 230/400 230/400 230/400
Protection degree / accessories IEC 592 IP41/55 IP41/55 IP41/55 IP41/55 IP41/55 IP41/55
Resistance 20O [mΩ/m] 6.8 6.8 6.8 3.0 3.0 3.0
Resistance 35O [mΩ/m] 8.3 8.5 8.5 3.8 3.8 3.8
Reactance Greq. H2 50 [mΩ/m] 0.21 0.22 0.22 0.19 0.19 0.19
Resistance 35O [mΩ/m] 7.2 7.2 7.2 4.0 4.0 4.0
PE Housing mm2 AL 100 100 100 100 100 100
L1, L2, L3, L4, L5, Cross section mm2 Cu 2.5 2.5 2.5 5.3 5.3 5.3
Joule losses I2 RW/m 3.8 3.8 3.8 5.8 5.8 5.8
Short circuit 3 phase kA 2.8 2.8 2.8 3.0 3.0 3.0
Voltage drop for 3-phase 50Hz current, in Volts per 100m and per ampere with loads distributed along the run. Voltage drop for single phase 50Hz current: divide these values by 0.866
For COS. Ø=0.8 V/100m/A 0.68 0.25 0.59 0.25
For COS. Ø =0.9 V/100m/A 0.76 0.29 0.66 0.29
For COS. Ø=1 V/100m/A 0.83 0.31 0.72 0.31
Average loop resistance between live connectors
Rb1 ph ph OR ph N (at thermal stabilisation temperature 0 1) mΩ/m
16.66 16.66 16.66 7.10 7.10 7.10
Rb1 ph ph OR ph N (at conventional short circuit temperature) mΩ/m
20.90 20.90 20.90 8.52 8.52 8.52
Average loop reactanceXb ph ph mΩ/m 1.68 1.68 1.68 0.79 0.79 0.79
Xb ph N mΩ/m 2.08 2.08 2.08 0.83 0.83 0.83
Average loop resistance between live and PE conductors
Rb1 ph PE (at thermal stabilisation temperature 0 1) mΩ/m
9.08 9.08 9.08 3.81 3.81 3.81
Rb1 ph PE (at conventional short circuit temperature) mΩ/m
10.90 10.90 10.90 4.57 4.57 4.57
Average loop reactance Xb ph PE mΩ/m 1.3 1.3 1.3 1.28 1.28 1.28
IPK Ka 4.4 5.0 5.0 5.3 5.3 5.3
PT kA2 S 195.103 195.103 195.103 900.103 900.103 900.103
Temperature departing15O 20O 25O 35O 40O 45O
1.1 1.08 1.07 1 0.95 0.92
www.cmd-ltd.com 132
The right amount of light
We understand the importance of getting your lighting right. The quality of artificial lighting is one of the most important influences on performance in the work place - you need the right amount of lighting that works for every situation to maximise the potential for positive change.
Better control of lighting can reduce costs by 30-50% and significantly reduce carbon emissions at the same time if the right decisions are made when selecting the lighting controls. Over the next few pages we will guide you through the considerations and benefits to create an effective lighting control system and to ensure it improves comfort, reduces maintenance costs and imparts greater flexibility to the use of a workspace.
Did you know?
In the UK, lighting consumes around 58,000GWh each year which amounts to about 20% of the electricity generated. It is possible to cut your lighting bills by up to 50% by implementing energy saving measures like introducing daylight linking, presence detection, etc. Lighting in a typical office costs about £3/m2 annually but in the most efficient office only costs about £1/m2. Lighting a typical office overnight wastes enough energy to heat water for 1,000 cups of tea.
CMD design and manufacture a comprehensive range of lighting control solutions. We can take a project from specification to delivery on site - liaising with contractors and providing you with all the CAD support you will need to deliver and complete the project to your customer’s satisfaction.
So whatever the lighting project, let us handle the control aspect for you.
For the 30-50% energy savings• directly and by reducing cooling loads
For the building management• gives flexibility• futureproofs against layout changes
For the building owner• reduces wiring costs• eligible for enhanced capital allowance• modular scheme• less onsite commissioning
For the building user• provides local control• improves working environment
For Building Regulations Compliance• By energy saving legislation, such as
Part L2A & L2B 2010 in UK
Making the most of lighting control
Why choose a lighting control system?
(Source: Carbon Trust).
www.cmd-ltd.com 134
Lighting control equipment & installation cost £12,605 £15,730 £17,583
Lifetime (Years) 11.4 19.0 19.0
Energy Cost (£/Yr) £3,031 £1,846 £1,486
Total Annual Cost £4,135 £2,673 £2,410
Payback Period (Years) - 2.6 3.2
The real cost of inefficient lighting
It’s well known that lighting accounts for around 20% of a business’ energy costs, or put another way, that’s nearly a fifth of a typical electricity bill. (Source: Carbon Trust).
New research has found that up to 40% of an electricity bill is spent on inefficient lighting. Take a look at some examples where lighting can become an unnecessary cost to your business:
• Lights are left on when they’re not needed. A typical office is only occupied between 25-30% of the week• If a building is lit constantly around the clock that equates to a staggering 70-75% energy wastage – or around
10% of your overall electricity bill• No lighting control system has been installed, or if one has, it hasn’t been programmed to supply light only when
needed• An older lighting management system is in place
Here are some simple but effective tips to cut down on electricity bills: • Reduce heat loss by installing automatic doors• Replace out of date and inefficient lighting with long-lasting, quality LEDs• Ensure all electrical equipment is turned off when not in use• Make sure display lighting is up-to-date• Check that the controls for heating and cooling at are the correct setting
Example application - Open plan office
1000m2 Electronic T5 fluorescent lighting, 33% of area daylight influenced. Manually
SwitchedAbsenceDetection
DaylightDimming
Making the most of lighting control
135sales line: +44 (0)1709 829511
Features
• 4 Pole• One channel• 1-Way Manual Switching or Presence Detection• Optional Daylight Hold Off when used with PIR• 230v Switching• 1 luminaire output• No commissioning required• Lightweight Flame Retardant ABS Casing• 100% factory tested
Sirius local switch module (LSM)
Switching options available are:
• Manual Switching via a 1-way 230v wall switch• Presence detection via a 230v PIR• Presence detection as above with Daylight Hold Off (all lights)
Each LSM has four 4 Pole ports assigned as follows:
• 1x Unswitched in for the power in feed• 1x Unswitched out to enable other modules to be connected to the same circuit• 1x Switch port for a 230v wall switch or a 230v PIR• 1x Luminaire output
Mains in
Mains out
Sirius standard switching configurations
For when you need a simple piece of kit to offer 1 Way Manual Switching, 2 Way Manual Switching or Presence Detection with the optional daylight hold off feature. All our switch modules are pre-wired and commissioned to eliminate any chance of wiring faults and can be changed or re-positioned without major disruption on site.
www.cmd-ltd.com 136
Technical Data
Sirius local switch module (LSM)
All 230v Switch Modules require a 4 core (live, neutral, earth and permanent live) feed to enable the module to function correctly.
• Each 230v 1-Way Switch Module has been provided with a port for the incoming unswitched feed and a port for the outgoing switched feed to the luminaires. Ports are also provided for both the outgoing unswitched feed so additional modules can be attached to the same circuit and for the connection to the 230v 1-way wall switch or 230v PIR. Wieland GST 18i 4 Pole plugs are required to connect to these ports
• Each 230v 2-Way Switch Module has been provided with a port for the incoming unswitched feed and a port for the outgoing switched feed to the luminaires. Ports are also provided for two 230v wall switch drops. There is no facility for an unswitched feed to allow further modules to be attached to the same circuit. Wieland GST 18i 4 Pole plugs are required to connect to these ports
• When using a 1-Way Switch Module with multiple PIRs a 230v 3-Way Circuit Splitter Module should be used to provide the additional ports needed
• When using a 2-way Switch Module with 3 or more switch points additional wall switches can be installed using a 230v Intermediate Switched T Piece
• If used the wall switch for a 230v Switch Drop must be a positive action switch
• The emergency test may take place at the distribution boards or via a local key switched T piece – there is no built in facility for testing the emergency live
Supply voltage: 230 Volts AC +10%/-6% 50Hz
Current Rating: 16Amp
Relay Rating: See the 230v PIR Data Sheet (available on request)
IP Rating: IP2X
Connection: Via Wieland GST 18i 4 pole female, male locking/latching type, complying with the requirements of BS EN 61535 : 2009
Operating temperatures: -5°C to 35°C
Sirius casings are manufactured from flame retardant ABS.
All SIRIUS units are 100% factory tested. To ensure traceability all Sirius units are labelled with the date of testing and a unique serial number both of which are also recorded electronically.
Code Description
P690803000.0 4 Pole Local Switch Module (Plastic) (1.5mm2) (Wall Switch or Presence)
P690804000.0 4 Pole 2 Way Switch Module (Plastic) (1.5mm2)
137sales line: +44 (0)1709 829511
Technical Data
• All BMB’s require a 4 core (live, neutral, earth and permanent live) feed to enable the unit to function correctly• Each BMB has been provided with a port each for the incoming and outgoing unswitched feed allowing further
modules to be attached to the same circuit. The following port configurations are used:* For the 1 Channel BMB nine (9) ports are provided for connection to the luminaires and one (1)
port is provided for connection to the 230v PIR or 230v Wall Switch Drop Lead* For the 2 Channel BMB eight (8) ports are provided for connection to the luminaires (four (4) per
channel) and one (1) port per channel is provided for connection to the 230v PIR or 230v Wall Switch Drop Lead
• In all cases Wieland GST 18i 4 Pole plugs are required to connect to these ports• When using a BMB with multiple PIRs a 230v 3-Way Circuit Splitter Module should be used to provide the
additional ports needed• If used the wall switch for a 230v Switch Drop must be a positive action switch
Supply voltage: 230 Volts AC +10%/-6% 50HzCurrent Rating: 16AmpRelay Rating: See the 230v PIR Data Sheet (available on request)IP Rating: IP2X
Connection Via Wieland GST 18i 4 pole female, male locking/latching type, complying with the requirements of BSEN 61535 : 2009.
Operating temperatures -5°C to 35°C
All PROXIMA casings are manufactured from a galvanised material equal to DX51D G275 in accordance with BS EN 10142:2000. External mounting flanges are fitted to allow quick and easy installation within the ceiling void.
All PROXIMA units are 100% factory tested. To ensure traceability all PROXIMA units are labelled with the date of testing and a unique serial number both of which are also recorded electronically.
Features
• One or Two Independent Channels• 1-Way Manual Switching or Presence Detection• Optional Daylight Hold Off when used with PIR• 230v Switching• 9 (one channel) or 8 (two channel - 4 per
channel) luminaire outputs• No commissioning required• Strong Steel Casing• 100% factory tested
Proxima basic marshalling box (BMB)Our BMBs offer plug-in simplicity at the more affordable end of the spectrum. All our units provide a simple and quick install not only in terms of time but cost savings as well. Units are pre-wired and commissioned to eliminate any chance of wiring faults and can be changed or re-positioned without major disruption. Proxima is our basic unit. A low cost option for the connection of luminaires to either presence detectors or conventional switches with the added feature of optional daylight hold off.
Mains out 4 pole connectors
Mains in
Switching port
www.cmd-ltd.com 138
Proxima basic marshalling box (BMB)
Code Description
P692041000.0 1 Channel Basic Marshalling Box
P692043000.0 2 Channel Basic Marshalling Box
Switching options available are:
• Manually Switched via a 1-way 230v wall switch
• Presence detection via a 230v PIR.• Presence detection as above with Daylight Hold
Off (all luminaires).
(Manually Switched or Presence Detection Channels):
Each independent channel on this type of BMB has the following switching options:
• Manually Switched via a 1-way 230v wall switch
• Presence detection via a 230v PIR• Presence detection as above with Daylight Hold
Off (all luminaires)
Proxima types & standard switching configurations
Each PROXIMA unit is a 4 Pole One or Two Channel 230v Switching Module utilising either a 230v 1-Way Wall Switch or a 230v Combined Presence and Daylight Sensor to control the lights.
1 Channel 2 Channel
139sales line: +44 (0)1709 829511
Our CDBs offer the simplicity of a ‘plug and play’ install saving valuable time on site and can be energy saving. All our units are pre-wired and commissioned prior to despatch to eliminate any chance of wiring faults and can be changed or re-positioned without major disruption. Rigel is the popular standard choice for connection of luminaries to either presence, absence or retractive switches with the added feature of SELV switching and optional daylight hold off.
Features
• One or two independent channels• Manual Switching, Presence or Absence Detection• Optional Daylight Hold Off when used with PIR• Flexible SELV Switching• 10 luminaire outputs (two channel – 5 per channel)• Built in emergency test facility• No commissioning required• Strong Steel Casing• 100% factory tested
Rigel circuit distribution box (CDB)
Mains in
Mains out
Technical Data
• All CDBs require a 4 core feed to operate correctly• Each CDB has twelve 4 Pole and three RJ45 ports assigned as follows:
* 1x 4 Pole Unswitched in for the power in feed* 1x 4 Pole Unswitched out to enable other modules to be connected to the same circuit* 1x RJ45 SELV Switch port for a SELV wall switch* 2x RJ45 SELV Switch ports for a SELV PIR* 10x 4 Pole luminaire outputs (split 5 to a channel for a 2 channel CDB)
• Multiple SELV switch points and/or PIR’s can be added with the use of additional RJ45 leads and/or RJ45 3-way splitters
• Multiple switches can be installed with the use of the same RJ45 SELV wall switch drop lead• If used the channel switches must be momentary push to make type switches• Emergency testing facility built in via a SELV wall switch (if required)
Conformity: Directive EMC 89/336/EEC Directive LVD 2006/95/EC Unit independently tested to comply with the requirements of: BS EN 60669-2-1:2004 BS EN 60669-2-3:1999 BS EN 55015:2006 BS EN 61000 series of standards for EMC compatibility
Supply voltage: 230 Volts AC +10%/-6% 50HzCurrent Rating: 16AmpRelay Rating: 16A resistive & incandescent 6A fluorescent 3A Compact fluorescent 3A Low Energy 3A Ventilation FansRJ45 Wiring: T568B CAT 5. 5/12v DC SELV
IP Rating: IP2X
Connection via Wieland GST 18i 4 pole female, male locking/latching type, complying with the requirements of BS EN 61535 : 2009
Operating temperatures -5°C to 35°C
All RIGEL casings are manufactured from agalvanised material equal to DX51D G275 in accordance with BS EN 10142:2000. External mounting flanges are fitted to allow quick and easy installation within the ceiling void.
All RIGELs are 100% factory tested. To ensure traceability all RIGELs are labelled with the date of testing and a unique serial number both of which are also recorded electronically.
www.cmd-ltd.com 140
(P1 - 1 Channel)Switching options available are:
• Presence Detection via a SELV PIR• Presence Detection with Daylight Hold Off (all
luminaires)
An override on facility is built in to this module(operated via an SELV Wall Switch) which will hold alllights on until released.
(P2 - 2 Channels)Each independent channel on this type of unit hasthe following switching options:
• Presence Detection via a SELV PIR• Presence Detection via a SELV PIR with Daylight Hold
Off (all luminaires on that channel only)
An override on facility is built in to this module (operated via a SELV Wall Switch) which will hold all linked channels on together until released.
This module may be used over two separate rooms/areas and 1 channel may operate in a different switching option to the other.
Rigel circuit distribution box (CDB)
Code Description
P692050000.0 CDB P1 (1 Channel Presence and Daylight Hold Off)
P692051000.0 CDB P2 (2 Channel Presence and Daylight Hold Off)
P692052000.0 CDB A1 (1 Channel Absence and Daylight Hold Off)
P692053000.0 CDB A2 (2 Channel Absence and Daylight Hold Off)
RIGEL Types and standard switching configurations
Each RIGEL unit is a 4 Pole One or Two Channel SELV Switching Module utilising SELV Wall Switches and/or SELVCombined Presence and Daylight Sensors to control the lights.
(A1 - 1 Channel)Switching options available are:
• Manually switched via a SELV Wall Switch• Absence detection via a SELV Wall Switch and SELV
PIR• Presence detection as above with Day Light Hold Off
(all lights)
(A2 - 2 Channels)Each independent channel on this type of CDB has the following switching options:
• Manually switched via a SELV Wall Switch• Absence detection via a SELV Combined Presence
and Daylight Sensor• Absence detection as above with Day Light Hold Off
(all lights on that channel only)
An override on facility is built in to this module operated via an SELV Wall Switch).
This module may be used over two separate rooms/areas and 1 channel may operate in a different switching option to the other.
Presence Detection Absence Detection
141sales line: +44 (0)1709 829511
Canis lighting control module (LCM)
Features
• Two linked channels• Manual Switching, Presence or Absence Detection• DSI or Broadcast DALI• Can be used with dimmable and non-dimmable lights via the LCMs integral relays• Daylight Linked and manual Dimming available• Dim down before switch off feature• Flexible SELV Switching• 8 luminaire outputs• Built in emergency test facility• No commissioning required – all LCMs are factory pre-programmed• Strong Steel Casing• 100% factory tested
Each CANIS unit is a 6 Pole Two Channel SELV Switching Module utilising SELV wall switches and/or SELV Combined Presence and Daylight Sensors to control the lights.
8 luminaire ports
Switching portPIR port
Mains outMains in
LCMs bring together the energy saving functionality of daylight linking where natural daylight is balanced with artificial lighting to not only reduce the energy required for lighting but also making the most of the daytime light as well offering two linked channels. The units are simple to install and can be re-programmed as and when your needs may change in the future. The system can be used to control all types of lighting – fluorescent, low voltage and mains voltage and is the perfect solution for the connection of luminaries to either presence, absence or conventional switches with the added feature of daylight linked dimming and SELV switching.
www.cmd-ltd.com 142
Canis lighting control module (LCM)
Technical Data
• All LCMs require a 4 core feed to operate correctly• Each LCM has two 4 Pole, two 6 Pole and two RJ45 ports assigned as follows:
* 1x 4 Pole Unswitched in for the power in feed* 1x 4 Pole Unswitched out to enable other modules to be connected to the same circuit* 1x RJ45 SELV Switch port for a SELV wall switch* 1x RJ45 SELV Switch port for a SELV PIR* 8 x 6 Pole luminaire outputs (4 for channel 1, 4 for channel 2)
• Multiple SELV switch points and/or PIRs can be added with the use of additional RJ45 leads and/or RJ45 3 way splitters
• Multiple switches can be installed with the use of the same RJ45 SELV wall switch drop lead• DSI LCMs are designed to operate luminaires with Tridonic DSI ballasts and standard non-dimmable HF
ballasts – all non-dimmable ballasts will switch on/off via the LCM’s integral relays• DALI LCMs are designed to operate luminaires with DALI ballasts and standard non-dimmable HF ballasts
– all non-dimmable ballasts will switch on/off via the LCM’s integral relays• All LCMs are designed to control up to 20 ballasts per channel• If used the master wall switch must be a 2-way centre off momentary push to make rocker type switch.
This switch is used to manually dim the luminaires – pressing and holding the top of the switch will increase the output of the lights, pressing and holding the bottom of the switch will decrease the output of the lights. With absence LCMs this switch is used to turn the LCM on
• If used the channel switches must be momentary push to make type switches• Emergency testing facility built in via a SELV wall switch (if required)
Conformity: Directive EMC 89/336/EEC Directive LVD 2006/95/EC Unit independently tested to comply with the requirements of: BS EN 60669-2-1:2004 BS EN 60669-2-3:1999 BS EN 55015:2006 BS EN 61000 series of standards for EMC compatibility
Supply voltage: 230 Volts AC +10%/-6% 50HzCurrent Rating: 16AmpRelay Rating: 16A resistive & incandescent 6A fluorescent 3A Compact fluorescent 3A Low Energy 3A Ventilation FansRJ45 Wiring: T568B CAT 5. 5/12vDC SELV
IP Rating: IP2X
Connection via Wieland GST 18i 4 pole female, malelocking/latching type, complying with therequirements of BS EN 61535 : 2009
Operating temperatures-5°C to 35°C
All CANIS unit casings are manufactured from a galvanised material equal to DX51D G275 in accordance with BS EN 10142:2000. External mounting flanges are fitted to allow quick and easy installation within the ceiling void.
All CANIS units are 100% factory tested. To ensure traceability all CANIS units are labelled with the date of testing and a unique serial number both of which are also recorded electronically.
Code Description
CANIS Range - 8 Port 2 Channel DSI Dimming LCMs
P692070000.0 LCM P1 (DSI)
P692071000.0 LCM A2 (DSI)
P692072000.0 LCM W2 (DSI)
CANIS Range - 8 Port 2 Channel DALI Dimming LCMs
P692075000.0 LCM P1 (DALI)
P692076000.0 LCM A2 (DALI)
P692077000.0 LCM W2 (DALI)
143sales line: +44 (0)1709 829511
Canis lighting control module (LCM)
Manual Switching
Presence Detection
Absence Detection
CANIS Types and available standard switching configurations
Switching options available are:
• Manually Switched via a SELV Wall Switch. Manual dimming is available
Separate switches can be installed to enable the switching of each of the two channels; this could for example be used to allow the separate switching of the teaching wall lights in a classroom.
Manual dimming is available via the master wall switch.
Switching options available are:
• Presence Detection via a SELV PIR with Daylight Linked Dimming (all lights)• Presence Detection as above with the addition of SELV Wall switches to control each Channel and/or Manual
Dimming for all channels together
An override on facility is built in to this module (operated via a SELV Wall Switch) which will hold all linked channels on together until released.
Separate switches can be installed to enable the switching of each of the three channels; this could for example be used to allow the separate switching of the teaching wall lights in a classroom.
Manual dimming is available via the master wall switch.
Additionally a 10% dim down before switch off facility is built in to warn the occupants of a room that the lights are about to switch off (reactivation by triggering the sensor).
Switching options available are:
• Absence Detection via a SELV Wall Switch and a SELV PIR. Manual dimming is available• Absence Detection with Daylight Linked Dimming (window row(s) lights only)
Separate switches can be installed to enable the switching of each of the three channels; this could for example be used to allow the separate switching of the teaching wall lights in a classroom.
Manual dimming is available via the master wall switch which is used to switch the LCM on and off.
Additionally a 10% dim down before switch off facility is built in to warn the occupants of a room that the lights are about to switch off (reactivation by triggering the sensor or by the SELV wall switch if the lights have been switched off).
www.cmd-ltd.com 144
Canis lighting control module (LCM)
145sales line: +44 (0)1709 829511
230v PIR sensor
• Presence Detection• Optional Daylight Hold Off• Pluggable – no onsite wiring required• 230v Switching• No commissioning required
230v Combined Passive Infra Red and Daylight Sensor
Each 230v Sensor is a multifunctional fully adjustable combined passive infra red and daylight (LUX) sensor.
• Sensitivity controls under removable bezel• Side mounted PIR or PIR/LUX selector switch• Integral securing wings for easy installation• Lightweight Flame Retardant ABS Casing• 100% factory tested
Each PIR has 3 adjustment screws to allow the user to configure the PIR to suit the condition of the room it is installed in. Operating the following settings:
Code Description
P699907000.0 Pluggable (Wieland) 230v Combined Presence and Daylight Sensor
LUX LevelThe point at which the PIR will either hold the luminaires off or begin to dim them (dependent on control module type) can be set by adjusting this control. The LUX level may be set between 200 and 2000 LUX.
Time DelayThe time that the PIR will hold the luminaires on before switching them off can be set between 15 seconds and 30 minutes.
PIR SensitivityThe range that the passive infra red sensor detects out to can be adjusted up to a maximum of 7 metres diameter (when installed at 2.4m height).
These sensors may be used with Sirius LSMs and Proxima BMBs.
www.cmd-ltd.com 146
230V PIR sensor
Technical Data
Conformity: Directive EMC 89/336/EEC Directive LVD 2006/95/EC Unit independently tested to comply with the requirements of: BS EN 60669-2-1:2004 BS EN 60669-2-3:1999 BS EN 55015:2006 BS EN 61000 series of standards for EMC compatibility
Supply voltage: 230 Volts AC +10%/-6% 50HzCurrent Rating: 16AmpRelay Rating: 16A resistive & incandescent lighting 6A fluorescent 3A Compact fluorescent 3A Low Energy 3A Ventilation FansIP Rating: IP2X
Connection via Wieland GST 18i 4 pole female, male locking / latching type, complying with the requirements of BS EN 61535 : 2009. All connectors are designed to comply with IEC 61535 (ed.1): 2009-02.
Operating temperatures-5°C to 35°C
Plastic PIR casings are manufactured from flame retardant ABS
All PIRs are 100% factory tested. To ensure traceability all PIRs are labelled with the date of testing and a unique serial number both of which are also recorded electronically.
Each PIR has a side selector switch which allows the user to configure the PIR for 1 of the following operational modes:
• PIR/LUX used for combined presence and daylight hold off.• LUX used if daylight hold off on its own is required.• PIR used if presence detection on its own is required.• The side selector switch must be set before the PIR is installed.
The adjustment screws are hidden to prevent being tampered with.
PIR selector
Securing wings
147sales line: +44 (0)1709 829511
12v Combined Passive Infra Red and Daylight Sensor
12V SELV Combined Passive Infra Red & Daylight Sensor (For RIGEL CDBs & CANIS LCMs)
• Presence Detection• Optional Daylight Hold Off• Pluggable – no onsite wiring required• Flexible SELV Switching• No commissioning required
• Sensitivity controls under removable bezel• Side mounted PIR or PIR/LUX selector switch• Integral securing wings ease for of installation• Lightweight Flame Retardant ABS Casing• 100% factory tested
Each PIR has 3 adjustment screws to allow the user to configure the PIR to suit the condition of the room it is installed in. Operating the following settings:
Code Description
P699913000.0 Pluggable (RJ45) SELV Combined Presence and Daylight Sensor
12v SELV PIR sensor
LUX LevelThe point at which the PIR will either hold the luminaires off or begin to dim them (dependent on control module type) can be set by adjusting this control. The LUX level may be set between 200 and 2000 LUX.
Time DelayThe time that the PIR will hold the luminaires on before switching them off can be set between 15 seconds and 30 minutes.
PIR SensitivityThe range that the passive infra red sensor detects out to can be adjusted up to a maximum of 7 metres diameter (when installed at 2.4m height).
www.cmd-ltd.com 148
PIR selector
Securing wings
Technical Data
Conformity: Directive EMC 89/336/EEC Directive LVD 2006/95/EC Unit independently tested to comply with the requirements of: BS EN 60669-2-1:2004 BS EN 60669-2-3:1999 BS EN 55015:2006 BS EN 61000 series of standards for EMC compatibility Supply voltage: 12 Volts DCCurrent Rating: 16AmpRelay Rating: See RIGEL CDB or CANIS LCM Data Sheets (available on request)RJ45 Wiring: T568B CAT 5. 5/12vDC SELVIP Rating: IP2X
Connection via RJ45 male plugs
Operating temperatures-5°C to 35°C
Plastic PIR casings are manufactured from flameretardant ABS
All PIRs are 100% factory tested. To ensure traceability all PIR’s are labelled with the date of testing and a unique serial number both of which are also recorded electronically.
Each PIR has a side selector switch which allows the user to configure the PIR for 1 of the following operational modes:
• PIR/LUX used for combined presence and daylight hold off.• LUX used if daylight hold off on its own is required.• PIR used if presence detection on its own is required.• The side selector switch must be set before the PIR is installed.
Each 12v SELV Sensor is a multifunctional fully adjustable combined passive infra red and daylight (LUX) sensor.
The adjustment screws are hidden to prevent being tampered with.
12V SELV PIR sensor
149sales line: +44 (0)1709 829511
12v SELV microwave sensor 12v SELV microwave sensor (Compatible with RIGEL CDB or CANIS LCM)
Features
• 2 sensitivity settings• Mounted almost anywhere• Radar technology• Resistant to false detections via environmental
conditions• Detection range up to 12m
• No line of sight required like infra red (can be hidden behind wood, glass etc.)
• Minimal power required• Sensor allows 12V DC supply to be shared with
other devices
Code Description
P699930000.0 12v SELV microwave sensor
Time DelayThe time that the microwave will hold the luminaires on before switching them off can be set between 15 seconds and 30 minutes.
Microwave SensitivityThe range that the passive infra red sensor detects out to can be adjusted up to a maximum of 12 metres diameter (when installed at 2.4m height).
www.cmd-ltd.com 150
Technical Data
• CW RADAR, ISM BAND• Centre Frequency is 5.8GHz• Detection range is 12m at high sensitivity setting (installation dependent)• Three sensitivity settings available: low, medium and high• Current consumption of circuit is 40mA max. @12V DC• Output compatible with RIGEL CDBs & CANIS LCMs• Radiated microwave energy is 30uW typical
Detection Range
12V SELV microwave sensor
Microwave sensitivity selector
Securing wings
2.8m
12m
151sales line: +44 (0)1709 829511
Pre-fabricated 4 pole accessoriesFeatures
• Complete pluggable systems for 16A power and lighting applications
• 4 or 6 Pole leads, T Pieces and Splitters available as standard
• Non-interchangeability between lighting and power wiring systems
• 1.5mm2 LSOH as standard in 3, 4, 5 or 6 cores• Wieland GST 18i 4 and 6 Pole connectors used as
standard
• Starter Leads, Drop Leads and Extender Leads available• 4 and 6 Pole Fixed and Flying Luminaire T Pieces
available• 4 and 6 Pole 3 Way Circuit Splitters available• 6 Pole leads, T Pieces and Splitters are suitable for DSI
and DALI controllers• Power Switched and Unswitched Fused Spurs for FCUs
etc.• 100% factory tested
4 pole female plugs - plug 4 pole female plugs - cover 4 pole male plugs - plug 4 pole male plugs - cover
Code
144010
Code
144013
Code
144007
Code
144013
Code
P690405001.0
Code
P690405003.0
Code
P690207003.0
Code
P690203003.0
Code
P690203005.0
1 metre 4 pole male to female
4 core 1.5mm2 LSOH lead
3 metre 4 pole male to female
4 core 1.5mm2 LSOH lead
3 metre 4 pole male to free end
4 core 1.5mm2 LSOH lead
3 metre 4 pole male to free end
3 core 1.5mm2 LSOH lead
5 metre 4 pole male to free end
3 core 1.5mm2 LSOH lead
Code
P690703000.3
Code
P690717000.3
Code
P690806000.0
Code
P690315003.0
Code
P690315005.0
4 pole luminaire fixed T piece
(Plastic) (1.5mm2) 0.3m 3 core drop
4 pole luminaire flying T piece
(Plastic) (1.5mm2) 0.3m 3 core drop4 pole 3 way circuit splitter
module (Plastic)
3 metre 4 pole 2 way
switch drop lead
5 metre 4 pole 2 way
switch drop lead
Code
P690303005.0
5 metre 4 pole 1 way
switch drop lead
Code
P690719000.3
4 pole luminaire flying T piece
(Plastic) (1.5mm2) 0.3m 4 core drop
Code
P690705000.3
4 pole luminaire fixed T piece
(Plastic) (1.5mm2) 0.3m 4 core drop
Code
P690405005.0
5 metre 4 pole male to female
4 core 1.5mm2 LSOH lead
Code
P690207005.0
5 metre 4 pole male to free end
4 core 1.5mm2 LSOH lead
Code
P690303003.0
3 metre 4 pole 1 way
switch drop lead
www.cmd-ltd.com 152
Pre-fabricated 6 pole accessories
6 pole female Plug - blue connector 6 pole female plug - white connector 6 pole female plug - base 6 pole female plug - hood
Code
144049
Code
144005
Code
144023
Code
144016
Code
144048
Code
144001
Code
144023
Code
144016
Code
P690474003.0
Code
P690474005.0
Code
P690250003.0
6 pole male plug - blue connector 6 pole male plug - black connector 6 pole male plug - base 6 pole male plug - hood
3 metre 6 pole male to female
6 core 1.5mm2 LSOH lead
5 metre 6 pole male to female
6 core 1.5mm2 LSOH lead
3 metre 6 pole male to free end
6 core 1.5mm2 LSOH lead
Code
P690249003.0
Code
P690249005.0
Code
P690248003.0
Code
P690247003.0
Code
P690247005.0
3 metre 6 pole male to free end
5 core 1.5mm2 LSOH lead
5 metre 6 pole male to free end
5 core 1.5mm2 LSOH lead
3 metre 6 pole male to free end
4 core 1.5mm2 LSOH lead
3 metre 6 pole male to free end
3 core 1.5mm2 LSOH lead
5 metre 6 pole male to free end
3 core 1.5mm2 LSOH lead
Code
P690748000.3
6 Pole / 6 tail fixed T piece (Plastic) (1.5mm2) 0.3m 6 core drop
Code
P690250005.0
5 metre 6 pole male to free end
6 core 1.5mm2 LSOH lead
Code
P690248005.0
5 metre 6 pole male to free end
4 core 1.5mm2 LSOH lead
Code
P690756000.3
6 pole / 6 tail flying T piece (Plastic) (1.5mm2) 0.3m 6 core drop
Code
P690754000.3
6 pole / 5 tail flying T piece (Plastic) (1.5mm2) 0.3m 5 core drop
Code
P690474001.0
1 metre 6 pole male to female
6 core 1.5mm2 LSOH lead
Code
P690746000.3
6 pole / 6 tail flying T piece (Plastic) (1.5mm2) 0.3m 5 core drop
6 pole 3 way circuit splitter module (Plastic)
Code
P690814000.0
153sales line: +44 (0)1709 829511
Technical Data
Leads, T Pieces and Splitters Specification
Supply voltage 230 Volts AC +10%/-6% 50HzCurrent Rating 16AmpIP Rating IP2XConnection Via Wieland GST 18i 4 or 6 pole female, male locking/latching type, complying with the requirements of BS EN 61535 : 2009. All connectors are designed to comply with IEC 61535 (ed.1): 2009-02.Operating temperatures -5°C to 35°C
Flexible Cable Specification
Material Low smoke zero halogen inner and outer sheaths IEC60332.3 Cat CCores 4Sizes 1.5mm2
Flame test to IEC 332/3A – Category C HD 405.3 VDE 0472 part 804 test CSelf-extinguishing VDE 0207 part 24 type HM2Acid test IEC 754-2Smoke density VDE 0482 part 268 IEC 1034-1/1034-2
Connector Specification
Wieland GST18 RangeNumber of Poles 4 Pole or 6 PoleRated Voltage 250VRated Impulse Voltage 4kV for 250V and 250/240VRated Current 16ACompliance DIN VDE 0628 (BS EN/IEC 61535 : 2009) DIN VDE 0625, EN 60320IP Rating IP20Insulation Components Thermoplastic material (polyamide), halogen-freeContact Parts Brass with nickel plating
Locking device in accordance to DIN VDE 0628
Pre-fabricated 6 pole accessories
Code
P690744000.3
Code
P690742000.3
6 Pole / 4 tail fixed T piece (Plastic) (1.5mm2) 0.3m 4 core drop
6 Pole / 3 tail fixed T piece (Plastic) (1.5mm2) 0.3m 3 core drop
Code
P690752000.3
Code
P690750000.3
6 Pole / 4 tail flying T piece (Plastic) (1.5mm2) 0.3m 4 core drop
6 Pole / 3 tail flying T piece (Plastic) (1.5mm2) 0.3m 3 core drop
Please note: Both 4 pole and 6 pole pre-fabricated wiring systems are available in a variety of lengths so please ask a member of our sales team for more information.
www.cmd-ltd.com 154
Analysis CostingFootprint records energy usage and presents the information on the dashboard. You can view graphs, make comparisons, and create pdf or csv reports.
Enter your own rates and Footprint will calculate the running or energy costs for all the equipment being monitored.
Footprint energy management
The footprint system helps identify ways of reducing power and saving money
www.cmd-ltd.com 156
Control Modules Dashboard
Footprint energy management
Modules are built with intelligent smart meter technology, with each module recording the energy usage of any devices plugged in.
The dashboard can be accessed via any standard internet browser, so no requirement for any additional software.
Different levels of control are available via the dashboard from full automation to manual overrides.
HIGHLY COMMENDED2012
157sales line: +44 (0)1709 829511
Footprint energy management
The gateway
The gateway is the link between the
power modules and the dashboard.
Transmitting data and sending
instructions. Note: Gateway MAC
addresses and PIN numbers, in relation
to their location, need to be logged.
The master socket
The master socket remains ON at
all times and it is recommended
this socket is used for the PC.
The smart meter
The smart meter is responsible
for recording the energy usage
of connected appliances.
The auxiliary sockets
The auxiliary sockets can be controlled
via the dashboard and switched ON/
OFF either manually or automatically.
www.cmd-ltd.com 158
Footprint energy management
The dashboard
Data is sent via the gateway and is displayed in
a user friendly format. The dashboard will allow
users to schedule, set thresholds, and control all
connected modules.
*Footprint is sold with a 12 month inclusive licence which includes access to, and exporting of, data together with technical support during office hours. A renewal licence fee will be applicable after the 12 month inclusive period expires. https://dashboard.cmdfootprint.co.uk.
Build it your way
159sales line: +44 (0)1709 829511
Footprint is a system that gives the user total control. Connecting appliances to the Footprint power module will allow users to collate energy usage data, monitor activity levels and schedule power.
Footprint energy management
The master socket with built in smart meter technology
The master socket is an uncontrolled outlet. The additional data obtained from this socket can be used to control the auxiliary sockets depending upon the operational mode set. The in-built smart meter measures and transmits highly accurate consumption data which can then be reported on.
The gateway
The Gateway is the hub of the system. The gateway sends messages from devices, equipment or web browsers using SSL certificates to encrypt the information that is passed. The SSL certificate provides encryption between the web browser or device and the host server platform and implements 128 bit AES/TLS encryption for all traffic. The gateways need to be positioned a minimum of 2m from a Wi-fi access point.
The power module
The power module allows users to connect appliances in order to make them smart as well as controllable. Using the recognised low power wireless technology of Zigbee®, the power module communicates to the Gateway allowing for energy monitoring and device control. Zigbee® has been designed for wireless mesh networking enabling hundreds of devices to transmit information to one another in real time. Due to its versatile nature, the mesh network also means that if one device stops transmitting, the system will continue to operate. The power modules are pre-configured to connect to the Gateway with minimal consumer set-up.
The dashboard
The control centre of operations, the Dashboard will allow different types of users to monitor activities and get involved. The Dashboard will collect energy usage and display it as usable data in the form of expenditure, CO2, and KWh used. Not only a monitoring tool, the Dashboard allows you to control the entire system.
1
2
3
4
Audit
You now have the tools to show users their energy consumption
on an individual, department or floor basis. This makes it easier
for users to take responsibility and ownership of their own
actions fuelling behavioural changes to take place.
Manage
With informed and evidence based data being available you
can improve your energy use.
Monitor
If you want to improve it you first have to monitor it. By seeing
exactly how much electricity is being consumed, it is easier to
introduce changes to make savings.
Target
When taking accurate readings it is easier for companies
to benchmark a starting point and then look to introduce
appropriate targets to measure the process being made.
www.cmd-ltd.com 160
Client outlines their requirements
and provides drawings of office plans
to CMD
Code Description
86E304GST 1 x power strip (Standard 1 x Master, 3 x Auxiliary Sockets)
161180*1 x gateway (POE/Power over Ethernet) *Cat5e cables are needed to route back to the server room.
Footprint energy management
Consultant & CMD have
initial briefing meeting & discuss
connection options
Quotation Raised
CMD Site Visit.Zigbee® connectivity test, wi-fi analysis and separate ASDL line or
server based assessment.
Order placed and relevant
documentation provided.
Hardware shippedto customer
Customer receives
hardware for installation
CMD first commission stage. Footprint units
allocated to Gateways, Zones and Groups
Final commissioning.
Customer training, Administrator
setup and project sign off
CMD provide continuous
technical support
External Process CMD Process
161sales line: +44 (0)1709 829511
Metal
Metal waste is segregated by type
and placed into labelled handling
bins ready to be collected and
recycled by a registered waste
management company.
Reuse RecycleReduce
Cardboard
High and low density cardboard
is bailed ready to be collected
and recycled into new cardboard/
packaging by a registered waste
management company.
Plastic
Plastics and other dry mixed
recyclables are held in dedicated
containers to be recycled by a
registered waste management
company.
Social responsibility
Our Corporate Responsibility is clear and defined:
We are committed to continually reducing our impact on the environment and
surrounding areas. We monitor our own performance and the performance
of our suppliers and customers.
1356kgs Aluminium swarf
5568kgs Aluminium section
5624kgs Cable off cuts
1261kgs Brass
94091kgs Ferrous metals
www.cmd-ltd.com 162
FM 541560
EMS 579214
Head Office
Sycamore RoadRotherhamSouth YorkshireS65 1ENUnited Kingdom +44 (0)1709 829 511
London Showroom
99 Charterhouse StreetClerkenwellLondonEC1M 6HRUnited Kingdom+44 (0)20 7251 7080
163sales line: +44 (0)1709 829511
Head Office
Eastwood Trading EstateRotherhamSouth YorkshireS65 1ENUnited Kingdom+44 (0)1709 829 511
London Showroom
99 Charterhouse StreetClerkenwellLondonEC1M 6HRUnited Kingdom+44 (0)20 7251 7080