CMLIB AH A R D W A R E Reference ManualOMICRON Test Universe2Article number VESD0101 - manual version: CMLIB A.AE.1 OMICRON electronics 2000. All rights reserved.Theproductinformation,specifications,andalltechnicaldatacontainedwithinthismanualarenotcontractually binding. OMICRON reserves the right to make technical changes without announcement.OMICRON electronics is not to be held liable for statements and declarations given in this manual. Theuserisresponsibleforeveryapplicationdescribedinthismanual.OMICRONelectronicsexplicitlyexoneratesitselffromallliabilityformistakesinthismanual.Copyingorreproducingthismanual,wholly or in part, is not permitted without the expressed written consent of OMICRON electronics. Contents3ContentsContents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Preface to the Hardware Reference Manual. . . . . . . . . . . . . . . . . . . . . . . . .5Safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71 Function and Setup of CMLIB A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91.1Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91.2Connection terminals and Interfaces. . . . . . . . . . . . . . . . . . . . . . . . . . .91.2.1 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91.2.2 Schematic diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101.2.3 16 pin sockets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111.2.4 BNC terminal sockets 1-6. . . . . . . . . . . . . . . . . . . . . . . . . . . .121.3Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152.1Electromagnetic compatibility (EMC). . . . . . . . . . . . . . . . . . . . . . . . .152.2Mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153 Appendix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .173.1Deliverables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .173.2Accessories / Ordering information. . . . . . . . . . . . . . . . . . . . . . . . . . .17OMICRON Contact Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21CMLIB A4 Preface to the Hardware Reference Manual5Preface to the Hardware Reference ManualThe purpose of this Hardware Reference Manual is to familiarize users with CMLIB A, and to show how to properly use it in various application areas.The manual contains important tips on how to use CMLIB A safely, properly, and efficiently. Paying attention to these instructions can help you avoid danger, repair costs, and down time due to improper operation.It should be read and used by all people working with CMLIB A.In addition to the operations manual and the applicable regulations for accident prevention in the country and at the site of operation, the accepted technical procedures for safe and competent work should be heeded. CMLIB A6Safety instructionsBefore bringing CMLIB A into operation, please read carefully the following safety instructions.Without detailed knowledge of this information, it is not possible to bring CMLIB A into operation!CMLIB A should only be operated by trained personnel.Designated use CMLIB A should only be connected to SELV interfaces. Due to safety-relevant reasons, a connection with the front panel terminals of the CMC is not permitted. The 16 pin "CMC" interface should only be connected to the generator outputs of a CMC 156 (Gen. Out 7 - 12) or a CMC 256 (LL out 1 - 6). The 16 pin "Amplifier" interface should only be connected to an OMICRON amplifier, if a) the interface labelled "CMC" is connected to a CMC test set, orb) the analog signal inputs (BNC) are either not connected or applied with a defined signal level. CMLIB A should only be used when in a technically sound condition as well as when its use is in accordance with the regulations, in a safe manner, and mindful of the dangers while paying attention to the operations manual. In particular, avoid disruptions that could in turn affect safety! Do not operate CMLIB A under wet or moist conditions (condensation). Do not operate CMLIB A when explosive gas or vapors are present. CMLIB A should not be opened. If the device is opened, all guarantees are invalidated. Preface to the Hardware Reference Manual7GlossaryWithin this manual different symbols are used to especially highlight certain sections.These symbols are:NoteRefers to sections with special meaning respectively additional information.CautionRefers to sections with special safety relevant meaning.Reference informationRefers to references with extensive and detailed information to the current theme. CMLIB A89Function and Setup of CMLIB A1Function and Setup of CMLIB A1.1FunctionCMLIB A is a connection box for the usage with the analog low level outputs of the CMC or with the analog control inputs of the additional amplifiers CMA 156 and CMS 156. CMLIB A can also be connected between a CMC test set and an amplifier to additionally tab the signals.1.2Connection terminals and Interfaces1.2.1OverviewCMLIB A provides the following connection terminals: 16 pin "CMC" connection terminal to connect CMLIB A to the generator outputs of a CMC 156 (Gen. Out 7 - 12) or to a CMC 256 (LL out 1 - 6). 16 pin "Amplifier" connection terminal to connect CMLIB A to external amplifiers. 6 pcs. of BNC sockets to connect the analog signals. CMLIB A101.2.2Schematic diagramFigure 1-1:Schematic diagram of CMLIB A1 2 35 4 6OMICRON amplifier16 pin plug for the connection at Gen 7-12 of the CMC 156 or at LL out 6 of the CMC 25611Function and Setup of CMLIB A1.2.316 pin socketsFor the connection of CMLIB A with the CMC or with external amplifiers, the connection cable VEHK0003 is used (see also Table 3-2: Manufacturer Ordering Information on page 17).Figure 1-2:Left-hand sideLemo plug for interface to external amplifiersRight-hand sideLemo plug for interface to CMCTable 1-1:Pin layout of the16 pin Lemo plugsFor ordering information for the 16 pin Lemo plug refer to Table 3-2: Manufacturer Ordering Information on page 17.connector functionpin 1 signal L1-1pin 2 signal L1-2pin 3 signal L1-3pin 4 GNDpin 5 signal L2-1pin 6 signal L2-2pin 7 signal L2-3pin 8-16 reservedhousing shield connection CMLIB A121.2.4BNC terminal sockets 1-6The following table shows the signal assignment at the BNC terminal sockets depending on the connected device.Table 1-2:signal assignment at the BNC socketsThe technical specification of the analog signals can be found in the "User manual CMC 156", "User manual CMC 256" or "User manual amplifier".BNC socket CMC 156 CMC 256 amplifier1 Gen. Out 10 LL out 4 L1-I2 Gen. Out 11 LL out 5 L2-I3 Gen. Out 12 LL out 6 L3-I4 Gen. Out 7 LL out 1 L1-II5 Gen. Out 8 LL out 2 L2-II6 Gen. Out 9 LL out 3 L3-II13Function and Setup of CMLIB A1.3WiringFigure 1-3:Wiring of CMLIB AGen. Out7 - 12Ext.Interf.AmplifierVEHK0008BNC to BNC connection cable VEHK0003 CMLIB A1415Technical data2Technical data2.1Electromagnetic compatibility (EMC)Table 2-1:Electromagnetic compatibility2.2Mechanical dataTable 2-2:Data regarding size and weightEMCCE conformity,requirementsThe product adheres to the determinations from the guidelines of the council of the european community for meeting the requirements of the member states regarding the electromagnetic compatibility.(EMC Guidelines 89/336/EWG)size and weightweight approx. 400gdimensions L x Wx H140 x 70 x 40mm CMLIB A1617Appendix3Appendix3.1DeliverablesBy default the following components are provided with CMLIB A: CMLIB A (VEHZ1101) Hardware Reference Manual (VESD0101) Connection cable CMC - CMLIB A (VEHK0003, identical with connection cable CMC 156 amplifier).3.2Accessories / Ordering informationTable 3-1:Ordering informationTable 3-2:Manufacturer Ordering InformationOrder Description Article NumberCMLIB A set VEHZ1105CMLIB A box VEHZ1101BNC to BNC connection cable VEHK0008BNC to 4mm banana connection cable VEHK0005additional user manual CMLIB A VESD0101Order Description Article NumberLemo plug with two guide cams and pull relief (for CMLIB A). Also refer to section 1.2.3 16 pin sockets on page 11.FGB.2B.316.CLAD 72ZLemo plug with one guide cams and pull relief (for CMC 156, ext. Interface). Also refer to section 1.2.3 16 pin sockets on page 11.FGG.2B.316.CLAD 72Zanti-bend bushing black GMA.2B.070 DN CMLIB A1819Contact Information / HotlineContact Information / HotlineEurope, Africa, Middle EastOMICRON electronics GmbHPhone: +43 5523 507-333E-Mail: info@omicron.atWeb: www.omicron.atAsia, PacificOMICRON electronics Asia Ltd, Hong KongPhone: +852 2634 0377E-Mail: info@asia.omicron.atWeb: www.omicron.atNorth and South AmericaOMICRON electronics Corp. USAPhone: +1 713 830-4660 or 1 800 OMICRONE-Mail: info@omicronusa.comWeb: www.omicronusa.comFor addresses of OMICRON offices with customer service centers, regional sales offices or offices for training, consulting and commissioning please see our website. OMICRON Contact Addresses2021IndexIndex16 pin sockets. . . . . . . . . . . . . . . . . . . . . . . . 11Aaccessories. . . . . . . . . . . . . . . . . . . . . . . . . . 17addressof manufacturer. . . . . . . . . . . . . . . . . . . . 19of representatives . . . . . . . . . . . . . . . . . . 19BBNC terminal sockets 1-6. . . . . . . . . . . . . . . 12Bringing into Operation. . . . . . . . . . . . . . . . . . 6CCE conformity. . . . . . . . . . . . . . . . . . . . . . . . 15connection terminals. . . . . . . . . . . . . . . . . . . . 9Ddeliverables. . . . . . . . . . . . . . . . . . . . . . . . . . 17dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . 15Eelectromagnetic compatibility . . . . . . . . . . . . 15EMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Ffunction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9Hhotline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19Iinterfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . .9Mmanufacturer address . . . . . . . . . . . . . . . . .19manufacturer ordering information. . . . . . . .17OOMICRON address . . . . . . . . . . . . . . . . . . .19Opening the device . . . . . . . . . . . . . . . . . . . .6order numbers . . . . . . . . . . . . . . . . . . . . . . .17ordering information. . . . . . . . . . . . . . . . . . .17Ppin layout . . . . . . . . . . . . . . . . . . . . . . . . . . .11pin layout of the 16 pin Lemo plugs. . . . . . .11 CMLIB A22Rrepresentatives addresses. . . . . . . . . . . . . . 19Sschematic diagram . . . . . . . . . . . . . . . . . . . . 10ServiceOMICRON address. . . . . . . . . . . . . . . . . 19setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9signal assignment at the BNC terminal sockets12Ttechnical data . . . . . . . . . . . . . . . . . . . . . . . . 15Wweight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13