cobo bytouchmachine control solution bytouchis a … control system 02_01_… · cobo...
TRANSCRIPT
COBO ByTouch Machine Control
Solution
Possible application :
• Firefighting vehicles
• Earthmoving vehicles
• Mining vehicles
• Emergency vehicles
• Lifting equipment
• Marine applications
• Airport vehicles
• Utility vehicles
6+6 Push button functions
configurable as:
• Latching switch on/off
• Momentary switch ON/OFF
• Latching switch on/off link
with input signal
• Momentary switch ON/OFF
link with input signal
ByTouch is a Compact and Powerful Digital Switch
Solution for all your needs
Fully programmable Touch Screen solution for any
kind of application & machinery.
You can choose from an existing range of icons (more than 100
available), additional icons can be created for any different needs
Backlight adjustable & the
possibility to monitor up to
two different Batteries
During the installation you can
choose what kind of switch
configuration is more suitable
for the application
by an existing range of icons.
COBO ByTouch Machine Control
State of the art Electronic control Devices for INPUTS and OUTPUTS:
• ON/OFF Inputs
• ON/OFF Outputs
• PWM Outputs
• ANALOGUE Inputs
• FREQUENCY Inputs
• Up to 150 AMP
• 2 CAN BUS
• 6-32Volts Power supply
• Reverse polarity protection
• Overload protection
• Overpower protection
• IP67
COBO ByTouch Machine Control
THE PAST
THE FUTURE
Long installation Time
Expensive wiring
Simple Installation
More flexibility
Standard wiring
Rocker switches
Fuses & Relays BoxLights and Services
Touch Screen display
Lights and
Services
Electronic controller
Electronic Engine
CAN BUS
J1939
COBO ByTouch Machine Control
COBO ByTouch Machine Control
Hazard Lighting
LED Strobe
Accessory Sockets and
Plugs
Rear lights
LED
Electronic Battery
Master Switches
Work Lights
Incandescent
LED
HID
Interior Lights
Incandescent
LED
Roll Over device
Acoustic Alarm
www.Cobo.com.au
info3b6.com.au
COBO ByTouch Machine Control
CAN BUS
Touch screen control panel
Power control unitCANBUS remote
control receiver
Remote control
REMOTE CONTROL OPTION
Remote control is available with 4 or 6 buttons (functions)
The system automatically will manage the commands coming from the
Touch screen control display or from the remote control unit
CONTROLLERS
State of the art Electronic control Devices IO-CAB
COBO ByTouch Machine Control
Storage temperature from - 30 °C to +85 °C (from - 40 °f to +185 °f)
Operating temperature from - 40 °C to +80 °C (from - 40 °f to +176 °f)
Sealing IP66
Power Supply Voltage 9 - 32v full operational, suitable for machine battery direct
connection
Max current 49A @ Tenv = +50 °C max, full loads
Load Dump protection ISO 7637-2
Idle Current Consumption 100 ma @ 12v
50 ma @ 24v
Inputs 3 Inputs Digital Inputs High Side/Low side
2 inputs Digital Inputs Low side
Outputs 2 Outputs 10Amps- 2 Outputs 6.5Amps –
4 Outputs 4 Amps -2 Output 2 Amps –
2 Outputs 250mAmp – 2 Output Half Bridge
EMC standards by 89/336 Ce
CE Mark – EMC (Emission/
Immunity)
EN 61000 - 6 - 3 (2006)
EN55022 (RF Emission)
EN 61000 - 6 - 2 (2005)
EN 61000 - 4 - 2 (electrostatic Discharge)
EN 61000 - 4 - 3 (radio frequency)
EN 61000 - 4 - 4 (burst)
EN 61000 - 4 - 6 (Conducted disturbance)
Safety Standard according ISO
13849-1
Mean time to Dangerous Failure
(MttFd)
18.2
Category 2
performance level (pL) Up to D
State of the art Electronic control Devices
Power Bridge:
COBO ByTouch Machine Control
Storage temperature from - 40 °C to +85 °C (from - 40 °f to +185 °f)
Operating temperature from - 40 °C to +80 °C (from - 40 °f to +176 °f)
Sealing IP67
Power Supply Voltage 6 - 32 v, suitable for direct vehicles battery connection
Max current 80 A @ Tenv = +50 °C max, full loads
Load Dump protection ISO 7637-2
Inputs 5 digital input, alarm functions
5 configurable inputs (digital, analogue or frequency)
3 digital inputs for address selection
Outputs 10 ON/OFF or PWM up to 8A
1 H-Bridge ON/OFF or PWM, at 3.5A for electric motors
Configurable status LEDs: 24
Idle Current Consumption < 20 mA @ 24 v (sleep mode)
EMC standards by 89/336 Ce
CE Mark – EMC (Emission/ Immunity)
EN 61000 - 6 - 3 (2006)
EN55022 (RF Emission)
EN 61000 - 6 - 2 (2005)
EN 61000 - 4 - 2 (electrostatic Discharge)
EN 61000 - 4 - 3 (radio frequency)
EN 61000 - 4 - 4 (burst)
EN 61000 - 4 - 6 (Conducted disturbance)
Safety Standard according ISO
13849-1
Mean time to Dangerous Failure
(MttFd)
> 100
Category 2
performance level (pL) Up to D
State of the art Electronic control
Devices Multiplex:
COBO ByTouch Machine Control
Storage temperature from - 40 °C to +85 °C (from - 40 °f to +185 °f)
Operating temperature from - 40 °C to +70 °C (from - 40 °f to +158 °f)
Sealing IP67
Power Supply Voltage 8 - 32v full operational, suitable for machine battery direct
connection
Max current 150A @ Tenv = +50 °C max, full loads
Load Dump protection ISO 7637-2
Idle Current Consumption 12mA Sleep mode
Inputs 9 Inputs Digital Inputs High Side/Low side
Outputs 15 Outputs 5 Amps- 2 Outputs 8 Amps –
1 Outputs 25 Amps -1 Output 35 Amps –
EMC standards by 89/336 Ce
CE Mark – EMC (Emission/
Immunity)
EN 61000 - 6 - 3 (2006)
EN55022 (RF Emission)
EN 61000 - 6 - 2 (2005)
EN 61000 - 4 - 2 (electrostatic Discharge)
EN 61000 - 4 - 3 (radio frequency)
EN 61000 - 4 - 4 (burst)
EN 61000 - 4 - 6 (Conducted disturbance)
Safety Standard according ISO 13849-1
IEC 62061
State of the art Electronic control
Devices CANVIEW3+ Touchscreen
display :
COBO ByTouch Machine Control
Solution
Storage temperature from - 35 °C to +80 °C (from - 40 °f to +185 °f)
Operating temperature from - 30 °C to +75 °C (from - 40 °f to +176 °f)
Sealing IP66
Power Supply Voltage 9 - 32 v, suitable for direct vehicles battery connection
Size
Connector 8 Pin Deutsch
Input 2 0-5 Volts Analogue inputs
1 Rpm – Hi Dig input
Communication Can BUS
LCD display Dot Matrix 176 x 80
Touch screen
Backlight adjustable
Buzzer Integrated
During start up pressing
the invisible button on the
display will access the
setting procedure
Here you can start to set
your switches by pressing
“Switch set “
How to Set Up:
Logo Page
Setup page
Switch position selection page
In this page you select the
position of the button you
would like to configure
COBO ByTouch Machine Control
Solution
Using left & right arrows
you can scroll the list of
pre-set icons until you find
one you want use
Icons selection
Switch type selection
In this page you could
decide if the switch button
selected has to be used as
a momentary or latching
switch
COBO ByTouch Machine Control
Solution
System has available 4 inputs
that can be link to the output
Selecting. 1, means that the
output number 4 will be enable
only if input 1 active
Selecting “NO” means that the
output “4” will not be depend
an any inputs
Input interlock
Save Setting
System will save settings
and it will now be ready to
work
COBO ByTouch Machine Control
Solution
Working Page
Ready to work
Input logic can be “inverted” highlighting the ‘invert’ button
COBO ByTouch Machine Control
Solution Example of a system controlling Rear light bar, individual work
lights, interior rear tray light, beacon on/off - auto off at 40kph,
reverse audible alarm on/off, hand brake on alarm integrated
with door open function, fitted to a Ford Ranger Dual Cab Ute.
COBO ByTouch Machine Control
Solution
COBO ByTouch Machine Control
Solution
Headquarter:
Via Tito Speri, 10
25024 Leno ( Brescia) ITALY
Phone: + 39 030 90451
Fax: +39 030 9045330
www.cobogroup.net
4/12 Maiella Street
Stapylton
4027 QLD, Australia
Phone: + 61 (0)7 3807 4866
Fax: + 61 (0)7 3807 6780
www.cobo.com.au