color spot 2500 at - usedstage.ru manual colorspot 2500e at.pdf · color spot 2500 at user manual...
TRANSCRIPT
ColorSpot 2500 AT
USER MANUAL
Version:1.7
ROBE®ShowLightings.r.o.CzechRepublicwww.robe.cz
�
Table of contents
1. Unpacking 42. Safety instructions 43. Operating determinations 54. Description of the fixture 65. Installation 8
5.1 Connection to the mains 85.2 Changing the power supply settings 85.3 Fitting the lamp 95.4 Lamp adjustment 95.5 Inserting/Exchanging gobos, colours and effects 105.6 Rigging the fixture 115.7 DMX-512 connection/connection between fixtures 135.8 Ethernet connection 13
6. DMX protocol 157. Controller mode 21
7.1 DMX addressing 217.2 Remotely controllable functions 21
8. Control menu map 229. Control menu 25
9.1 Fixture Address 259.2 Fixture information 259.3 Personality 279.4 Lamp On/Off 309.5 Test sequences 309.6 Manual mode 309.7 Stand-alone setting 309.8 Reset functions 319.9 Special functions 31
10. Power down mode 3311. RDM 3312. Error and information messages 3413. Technical specifications 3614. Maintenance and cleaning 38
ColorSpot 2500 AT
�
1. Unpacking
The ColorSpot 2500E AT cardboard box included items:-ColorSpot2500EAT-Usermanual(1piece)- Small paper box with:-Gobo-set1�(1piece)-MountingbracketOmegaCLassembled(2pieces)
Thesmallpaperboxissituatedinthetoppartofthecardboardbox.
CAUTION! Keep this device away from rain and moisture! Unplug mains lead before opening the housing!
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOU INITIAL START - UP!
2. Safety instructionsEverypersoninvolvedwithinstallationandmaintenanceofthisdevicehaveto:- be qualified-followtheinstructionsofthismanual
CAUTION! Be careful with your operations. With a high voltage you can suffer a dangerous electric shock when touching the wires!
Thisdevicehasleftourpremisesinabsolutelyperfectcondition.Inordertomaintainthisconditionandtoensureasafeop-eration,itisabsolutelynecessaryfortheusertofollowthesafetyinstructionsandwarningnoteswritteninthismanual.
Important:Themanufacturerwillnotacceptliabilityforanyresultingdamagescausedbythenon-observanceofthismanualoranyunauthorized modification to the device.
Please consider that damages caused by manual modifications to the device are not subject to warranty.
Neverletthepower-cordcomeintocontactwithothercables!Handlethepower-cordandallconnectionswiththemainswithparticularcaution!
Makesurethattheavailablevoltageisnothigherthanstatedontherearpanel.
Alwayspluginthepowerplugleast.Makesurethatthepower-switchissettooff-positionbeforeyouconnectthedevicetothemains.Thepower-plughastobeaccessableafterinstallingthedevice.
Makesurethatthepower-cordisnevercrimpedordamagedbysharpedges.Checkthedeviceandthepower-cordfromtimetotime.
Alwaysdisconnectfromthemains,whenthedeviceisnotinuseorbeforecleaningit.Onlyhandlethepower-cordbytheplug.Neverpullouttheplugbytuggingthepower-cord.
ThisdevicefallsunderprotectionclassI.Thereforeitisessentialtoconnecttheyellow/greenconductortoearth.
2500E
Open
5
The electric connection, repairs and servicing must be carried out by a qualified employee.Donotconnectthisdevicetoadimmerpack.
Do not switch the fixture on and off in short intervals as this would reduce the lamp’s life.
Duringtheinitialstart-upsomesmokeorsmellmayarise.Thisisanormalprocessanddoesnotnecessarilymeanthatthedeviceisdefective.
Do not touch the device’s housing bare hands during its operation (housing becomes hot)!Forreplacementuselampsandfusesofsametypeandratingonly.
CAUTION ! Avoid looking directly into the light sourceEYEDAMAGES ! (meant especially for epileptics) !
3. Operating determinationsThisdeviceisamoving-headspotforcreatingdecorativeeffectsandwasdesignedforindooruseonly.
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immedi-ately.Thearisingcondensationwatermightdamageyourdevice.Leavethedeviceswitchedoffuntilithasreachedroomtemperature.
Neverrunthedevicewithoutlamp!
Donotshakethedevice.Avoidbruteforcewheninstallingoroperatingthedevice.
Never lift the fixture by holding it at the projector-head as the mechanics may be damaged. Always hold the fixture at the transporthandles.
Whenchoosingtheinstallation-spot,pleasemakesurethatthedeviceisnotexposedtoextremeheat,moistureordust.Thereshouldnotbeanycableslyingaround.Youendangeryourownandthesafetyofothers!
Theminimumdistancebetweenlightoutputandtheilluminatedsurfacemustbemorethan5meters.
Make sure that the area below the installation place is blocked Always fix the fixture with an appropriate safety rope. Fix thesafety-ropeatthecorrectholesonly.
Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened.
The lamp must never be ignited if the objective-lens or any housing-cover is open, as discharge lamps may explose and emitahighultravioletradiation,whichmaycauseburns.
The maximum ambient temperature 35° C must never be exceeded. Otherwise, the lamp is switched off and the fixture isoutofoperationfor5minutes.
CAUTION! The lens has to be replaced when it is obviously damaged, so that its function is impaired, e. g. due to cracks or deep scratches!
Operate the device only after having familiarized with its functions. Do not permit operation by persons not qualified for operatingthedevice.Mostdamagesaretheresultofunprofessionaloperation!
CAUTION! The lamp has to be replaced when it is damaged or deformed due to the heat!
Pleaseusetheoriginalpackagingifthedeviceistobetransported.
Please consider that unauthorized modifications on the device are forbidden due to safety reasons!
Ifthisdevicewillbeoperatedinanywaydifferenttotheonedescribedinthismanual,theproductmaysufferdamagesandtheguaranteebecomesvoid.Furthermore,anyotheroperationmayleadtodangerslikeshort-circuit,burns,electricshock,burnsduetoultravioletradiation,lampexplosion,crashetc.
CAUTION! The head and yoke must be unlocked before operation! Check the pan/tilt locks!
�
4. Description of the fixture
Theheadcanbelockedfortransportation-thetiltlockbutton(�)ispushedandthepanlock/unlockpeg(�)isinalockposition.Tounlockthehead,pressthetiltunlockbutton(5)andmovethepanlock/unlockpeg(�)tounlockposition.
1-Yoke2 -Frontpanel3-FrontLens4-Tiltlockbutton(red)5-Tiltunlockbutton(green)6-Panlock/unlocklever7-Handle8-Base
Rear panel of the base 1 -Neutralfuseholder 2 - Livefuseholder3-Powercord 4 -Powerswitch 5-5-pinDMXoutput 6 - 5-pinDMXinput7-�-pinDMXoutput 8 -�-pinDMXinput 9-Ethernetinput
Front panel of the base1 - Networkindicator2 -Display 3-Infra-redsensor
4-Data-transferindicator 5-RNSencoderwheel 6-Escapebutton 7-Enterbutton
= LIVE= NEUTRAL= EARTH
LIVEFUSE
NEUTRALFUSE
MAINSINPUT
BROWNBLUEYEL/GREEN
T15A@230V
S eria l num ber:
OUT
ETHERNET
1 = GND2 = SIG.3 = SIG. +
5 - PIN OUT
3 - PIN
1 = GND2 = SIG.3 = SIG. +4 = FREE5 = FREE
IN
IN SERIALDATALINK
SERIALDATALINK
RJ - 45CONNECTOR
4
2
3
6
5 7 8
9
7
Head inside-top side 1 -Gobowheel2 2 - Colourwheel3 - CMY/conver.filter module 4 - Objective 5-Effectwheel 6 - Gobowheel17-Lampchamber
Head inside-bottom side 8 -Frostlamellas 9 - Iris10-Termostat 11 -Zoom/Focusmodule 12-Igniter 13 - Lampcover
�
5. Installation
5.1 Connection to the mains
Verify the power supply settings before applying power!
Thefactorysettingsareprintednexttothepowerswitch.Ifyouwishtochangethepowersupplysettings,seethenextchapter.Installla�-pronggrounding-typeplugonthepowercable.Theearthhastobeconnected!If you have any doubts about proper installation, consult a qualified electrician.
The occupation of the connection-cables is as follows:
Cable (EU) Cable (US) Pin InternationalBrown Black Live LLihtblue White Neutral NYellow/Green Green Earth
5.2 Changing the power supply settings
Electronic ballastTheoperatingrangeoftheelectronicballast is20�-255VAC,50-�0Hz.ThetransformerhastobesettothelocalACvoltage.
If you want to change the power supply settings, follow the instructions:1. Disconnect the fixture from AC power.2.Removethebothtopbasecoversbylooseningthe12screws.�.Movethewire(�)onthetransformerconnectionblocktothepositionaccordingtothedesiredvoltage.�.ClosethebasebeforeapplyingACpower.
Example:Powersupplysettins:2�0V/50Hz
�
5.3 Fitting the lamp
DANGER ! Install the lamps with the device switched off only. Unplug from mains before !
To insert the lamp (MSR GOLD 1200 FastFit):1. Disconnect the fixture from power and allow it to cool atleast15minutes.2. Make sure that fixture´s head is in the position asshownonthepicture.Loosenthetwoquarter-turnfasteners(1)marked“X,Y“onthelampcover(2)toturnthecoverdown.�.Holdingthelampbyitsceramicbase(�),carefullyturnthelamptotheleftasshownonthepictureinordertoloosenthelampfromthelampholder(�).Gentlypullthelampoutofthelampholder�.Holdingthenewlampbyitsceramicsbase,gently
insertthelamptothelampsocketandturnthebaseto the right. Make sure that the lamp is installedtightlyintothelampsocket.Donotinstallalampwithahigherwattage!Alamplike thisgenerates temperatures thedevice is notdesignedfor.Damagescausedbynon-observanceare not subject to warranty. Please follow the lamp manufacturer‘snotes!Donot touchtheglassbulbbarehandduringtheinstallation!
5.Reinsertthelampcover(2)andtightenthetwoquarter-turnfasteners(1)again.�.Alignthenewlamp(seeinstructionsbelow)7.Reset„LampOnTime”and„LampStrikes”counters
in„Fixtureinformation”menu.
Do not operate this fixture with opened lamp cover!
5.4 Lamp adjustment Thelampholderisalignedatthefactory.Due to differences between lamps, fine adjustment may improve light performance:
1. Switch on the fixture and after reset turn on the lamp.2.Cancelalleffects,opentheshutterandfocusthelightona
flat surface (wall) using either DMX controller or function „Lamp adjustment” in „Special functions menu”.
�.Centerthehot-spot(thebrightestpartofthebeam)usingthe3 adjustment screws “A, B, C”. Turn one screw at a time to drag the hot-spot, diagonally across the projected image. If you cannot detect a hot -spot, adjust the lamp until the light iseven.To reduceahot-spot, pull the lamp inby turningall threescrews„A,B,C”clockwise1/�-turnatatimeuntilthelightisevenlydistributed.Ifthelightisbrighteraroundtheedgethanitisinthecenter,or if light output is low, the lamp is too far back in the reflector. „Push”thelampoutbyturningthescrews“A,B,C”counter-clockwise1/�-turnatatimeuntilthelightisbrightandevenlydistributed.
1 -Quater-turnfasteners 2 - Lampcover3-Lampbase4 -Lampholder
Remove the screws X and Y for re-lamping
3 adjustment scews “A, B, C”
10
5.5 Inserting/Exchanging gobos, colours and effects
DANGER! Install the gobos, colours and prisms with the device switched off only. Unplug from mains before!
Turn off the lamp and allow it to cool for at least 10 minutes. Disconnect the fixture from power.
Open the top cover of the moving head by loosening the 4 quarter-turn fasteners on the top cover and follow the instructions below:
Rotating gobo-wheels:1. Gently bend out the gobo holder to release it from the fixative holes and eject it from the pressing snap.2.Presstheendsofthespringgobo-locktogetherwithanappropriatetoolandremoveit.
Donottouchthesurfaceofthepatternoftheglassgobosastheoilsfromyourhandscandamagethepattern.�.Removethedistanceringandgoboandinsertthenewgobo(glazy or aluminium side towards the lamp)withdistancering.Presstheendsofthespringgobo-locktogetherandinsertitinthefrontofthegobo.�.Putthegoboholderbackunderthepressingsnapandpushitto the 3 fixative notches.
CAUTION! The gobo holder with the magnet must be placed in the same gobo position as it was placed before gobo replacement!
Colour-wheel:1.Gentlybendoutthecolourmoduletoreleaseit
from the determinative pins and eject it from the pressing snap.2.Putthenewcolourmodulebackunderthepressing
snapandplaseitbetwen2determinativepins.
C olour m odu le
P ress ing snap
D eterm ina tivep ins
11
Effect-wheel:1.Gentlybendouttheeffectglassholdertorelease
it from the fixative holes and eject it from the pressing snap.
2.Presstheendsofthespringglass-locktogetherwith an appropriate tool and remove it. Remove theglassandinsertthenewone.
�.Presstheendsofthespringglass-locktogetherandinsertitinthefrontoftheglass.
�.Puttheglasseffectholderbackunderthepressingsnap and push it to the 3 fixative notches.
CAUTION! The effect glass holder with the magnet must be placed in the same glass position as it was placed before glass replacement!
5.6 Rigging the fixture
DANGER TO LIFE!Please consider the respective national norms during the installation! The installation must only be carried out by an authorized dealer!
The installation of the fixture has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without anyharmingdeformation.
Theinstallationmustalwaysbesecuredwithasecondarysafetyattachment,e.g.anappropriatecatchnet.Thissecondarysafetyattachmentmustbeconstructedinawaythatnopartoftheinstallationcanfalldownifthemainattachmentfails.
When rigging, derigging or servicing the fixture staying in the area below the installation place, on bridges, under high workingplacesandotherendangeredareasisforbidden.
Theoperatorhastomakesurethatsafety-relatingandmachine-technicalinstallationsareapprovedbyanexpertbeforetaking into operation for the first time and after changes before taking into operation another time.
Theoperatorhastomakesurethatsafety-relatingandmachine-technicalinstallationsareapprovedbyanexpertaftereveryfouryearinthecourseofanacceptancetest.
Theoperatorhastomakesurethatsafety-relatingandmachine-technicalinstallationsareapprovedbyaskilledpersononceayear.Allow the fixture to cool for ten minutes before handling.The projector should be installed outside areas where persons may walk by or be seated.
IMPORTANT!OVERHEADRIGGINGREQUIRESEXTENSIVEEXPERIENCE,including(butnotlimitedto)calculatingworking load limits, installationmaterialbeingused,andperiodicsafety inspectionofall installationmaterialand theprojector. If you lack these qualifications, do not attempt the installation yourself, but instead use a professional structural rigger. Improper installation can result in bodily injury and or damage to property.The fixture has to be installed out of the reach of people.If the fixture shall be lowered from the ceiling or high joists, professional trussing systems have to be used. The fixture must never be fixed swinging freely in the room.
Caution: Fixtures may cause severe injuries when crashing down! If you have doubts concerning the safety of a possible installation, do not install the fixture!Before rigging make sure that the installation area can hold a minimum point load of 10 times the fixture’s weight.
12
Danger of fire! When installing the device, make sure there is no highly inflamma ble material (decoration articles, etc.) in between a distance of min. 1,2 m.
CAUTION! Use 2 appropriate clamps to rig the fixture on the truss. Follow the instructions mentioned at the bottom of the base. Make sure that the device is fixed properly! Ensure that the structure (truss) to which you are attaching the fixtures is secure.
The moving-head can be placed directly on the stage floor or rigged in any orientation on a truss without altering its ope-rationcharacteristics.TheOmegaholderscanbeplacedin�positionsonthebottomofthebase.Usetheclamps(notincludedindelivery)withscrewsM12.For overhead use, always install a safety-rope that can hold at least 10 times the weight of the fixture. You must only use safetyropeswithscrew-oncarabines.Pullthesafetyropethroughthetwoaperturesonthebottomofthebaseandoverthe trussing system etc. Insert the end in the carabine and tighten the fixation screw.
Fixation via the omega holders1.Bolteachclamp(1)totheomega
holder(�)withM12boltandlocknutthroughtheholeintheholder.2.Fastentheomegaholdersonthe
bottomofthebasebyinsertingbothquick-lockfasteners(�)intotheholesofthebaseandtightenfullyclockwise.�.Fastenthesafety-rope(2)throughthe
twoaperturesonthebottomofthebaseandoverthetrussingsystem.
1 -Clamp2 -Safety-rope3 -Quick-lockfastener4 -Omegaholder
Possible omega holder 4 positions:
When installing fixtures side-by-side, avoid illuminating one fixture with another!
DANGER TO LIFE! Before taking into operation for the first time, the installation has to be approved by an expert!
1
2
3
4
1�
5.7 DMX-512 connection/connection between fixturesThe fixture is equipped with both 3-pin and 5-pin XLR sockets for DMX input and output.The sockets are wired in parallel.Onlyuseashieldedtwisted-paircabledesignedforRS-��5and�-pinor5-pinXLR-plugsandconnectorsinordertoconnect the controller with the fixture or one fixture with another.
Occupation of the XLR-connection: DMX - output DMX-input XLR mounting-sockets (rear view): XLR mounting-plugs (rear view):
IfyouareusingthestandardDMXcontrollers,youcanconnecttheDMXoutputofthecontrollerdirectlywiththeDMXinput of the first fixture in the DMX chain. If you wishhht to connect DMX controllers with other XLR outputs, you need to useadapter-cables.
Building a serial DMX chain:Connect the DMX output of the first fixture in the DMX chain with the DMX input of the next fixture. Always connect one output with the input of the next fixture until all fixtures are connected.Caution: At the last fixture, the DMX cable has to be terminated with a terminator. Solder a 120 ΩresistorbetweenSignal(–) and Signal (+) into a XLR plug and plug it in the DMX output of the last fixture.
5.8 Ethernet connectionThe fixtures on a data link are connected to the Ethernet with Art-Net communication protocol. The controlling software fromPC(orlightingconsole)hastosupportArt-Netprotocol.Art-Netcommunicationprotocolisa10BaseTEthernetprotocolbasedontheTCP/IP.ItspurposeistoallowtransferoflargeamountsofDMX512dataoverawideareausingstandardnetworktechnology.
IP address is the Internet protocol address. The IP uniquely identifies any node (fixture) on a network.The UniverseisasingleDMX512frameof512channels.
TheColorSpot2500EATisequippedwith�-pinRJ-�5socketforEthernetinput.Useanetworkcablecategory5(withfour „twisted” wire pairs) and standard RJ-45 plugs in order to connect the fixture to the network.
RJ-45 socket (front view):1-TD+ 5-Notconnected2-TD- 6-RX-3-RX+ 7-Notconnected4-Notconnected8-Notconnected
Patch cables that connect fixtures to the hubs or LANsocketsarewired1:1,thatis,pinswiththesamenumbersareconnectedtogether:
1-Shield2 -Signal(-)3-Signal(+)
4-Notconnected 5-Notconnected
If only the fixture and the computer are to be inter-connected,nohubsorotheractivecomponentsareneeded.Across-cablehastobeused:
pin 1 2 � � 5 � 7 �pin � � 1 � 7 2 5 �
pin 1 2 � � 5 � 7 �pin 1 2 � � 5 � 7 �
1�
Ethernet connectionConnect the Ethernet-inputs of all fixtures in the fixture chain with the network.Option “Ethernet” has to be selected from „Set Ethernet Mode” menu on the fixture.SetIPaddress(002.xxx.xxx.xxx/010.xxx.xxx.xxx)andtheUniverse.
Example:(DMXaddress=��)IPaddres=002.1��.002.00�Universe=1
An advised PC setting: IP address: 002.xxx.xxx.xxx / 010.xxx.xxx.xxx (Different from fixture IP addresses) NETmask:255.0.0.0
Ethernet / DMX connectionOptions „Ethernet/DMX” has to be selected from „Set Ethernet Mode” menu on the first fixture (connected to the network) in the fixture chain, next fixtures have standard DMX addresses.Connect the Ethernet-input of the first fixture in the data chain with the network. Connect the DMX output of this fixture with the input of the next fixture until all fixtures are connected to the DMX chain.Caution: At the last fixture, the DMX chain has to be terminated with a terminator. Solder a 120 ΩresistorbetweenSignal(–) and Signal (+) into a XLR-plug and connect it in the DMX-output of the last fixture.
Example:
(DMXaddress=1)IPaddres=002.1��.002.001Universe=1
(DMXaddress=25)IPaddres=002.1��.002.002Universe=1
DMX address=73
IPaddress=002.1��.002.002Universe=0
DMX address=25
DMX address=217 DMX address=25
DMX address=1
DMX address=1
IPaddress=002.1��.002.00�Universe=1
15
ColorSpot 2500E AT - DMX protocol,version 1.0
Mode / Channel 1 2 3
Value Function Type of control
1 1 19 0-255 PanPanmovementby5�0° proportional
2 2 20 0-255 Pan FineFinecontrolofpanmovement proportional
3 3 21 0-255 TiltTiltmovementby2�0° proportional
4 4 22 0-255 Tilt fineFinecontroloftiltmovement proportional
5 5 23
0
1-255
1-255
Pan/Tilt speed , Pan/Tilt timeMax.speed(trackingmode)*P./T. speed-set Speed Mode in menu: Pan/Tilt ModeSpeedfrommax.tomin.(vectormode)**P./T. time - set Time Mode in menu: Pan/Tilt ModeTimefrom0,1sto25,5s.***
step
proportional
proportional
6 6 24
0-�
10-1�20-2��0-��50-5��0-��70-7��0-���0-��
100-10�110-11�120-12�
1�0-1��1�0-1��150-15�1�0-1��170-17�1�0-1��1�0-1��200-20�210-22�2�0-2��2�0-255
Power/Special functionsReservedToactivatefollowingfunctions,stopinDMXvalueforatleast�sandshuttermustbeclosedatleast�s.(„Shutter,Strobe”channel2�(�0,1)mustbeatrange:0-�1DMX).****AutofocusOnAutofocusOffReservedPan/TiltspeedmodePan/TilttimemodeBlackoutwhilepan/tiltmovingDisabledblackoutwhilepan/tiltmovingBlackoutwhilecolourwheelmovingDisabledblackoutwhilecolourwheelmovingBlackoutwhilegobo1/gobo2movingDisabledblackoutwhilegobo1/gobo2movingTo activate following functions,stop in DMX value for at least 3 s.LampOn,reset(totalresetexceptpan/tiltreset)Pan/TiltresetColoursystemresetGobosystemresetDimmer/StroberesetFocus/Zoom/FrostresetIris/Effect/resetTotalresetReservedLampOffReserved
step
stepstepstepstepstepstepstepstepstepstepstep
stepstepstepstepstepstepstepstepstepstepstep
Notes: *Range0-255DMXatmax.speed(0DMX): pan=�.5s tilt=�.�s **Range0-255DMXatmin.speed(255DMX): pan=�7min.10s tilt=1�min.��s ***Shorttimesarenotusedforlongtracks(e.g.0.5sfortrack0-255DMX).Timesarerestrictedbymechanical parameters of the fixture. ****Theswitch-functionshaveprioritytotheequivalentfunctionsinmenu„Personality”butthesettingbyDMX is not saved to the memory (after switching the fixture on,the setting from menu „Personality” is loaded and afterthatcanbychangedwithDMXvalueonthechannel�). DMX protocol menu „Personality”
10-1�AutofocusOn Autofocus-->On20-2�AutofocusOff Autofocus-->Off50-5�Pan/Tiltspeedmode Pan/Tiltmode--->SpeedMode�0-��Pan/Tilttimemode Pan/Tiltmode--->TimeMode70-7�Blackoutwhilepan/tiltmoving ActiveblackoutWhile-->Pan/TiltMoving-->On�0-��Disabledblackoutwhilepan/tiltmoving ActiveblackoutWhile-->Pan/TiltMoving-->Off�0-��Blackoutwhilecolourwheelmoving ActiveblackoutWhile-->ColourWheelMoving-->On100-10�Disabledblackoutwhilecolourwheelmoving ActiveblackoutWhile-->ColourWheelMoving-->Off110-11�Blackoutwhilegobo1/gobo2moving ActiveblackoutWhile-->GoboWheelsMoving-->On120-12�Disabledblackoutwhilegobo1/gobo2moving ActiveblackoutWhile-->GoboWheelsMoving-->Off
1�
Mode / Channel 1 2 3
Value Function Type of control
7
0-�10-�1�2-����-�5
��-12712�-15�1�0-1�11�2-22�22�-255
Pan/Tilt macro selectionDisabledpan/tiltmacroReservedFigureofcircle(fromsmalltolarge)Figureofhorizontaleight(fromsmalltolarge)Figureofverticaleight(fromsmalltolarge)Figureofrectangle(fromsmalltolarge)Figureoftriangle(fromsmalltolarge)Figureofstar(fromsmalltolarge)Figureofcross(fromsmalltolarge)
stepstep
proportionalproportionalproportionalproportionalproportionalproportionalproportional
80
1-12712�-12�1�0-255
Pan/Tilt macro speedNomacrogenerationMacrogenerationfromfasttoslow-forwardsNomacrogenerationMacrogenerationfromslowtofast-backwards
stepproportional
stepproportional
7 9 70
1��7557��1
11012�-12�1�0-1��1�0-1��150-15�1�0-1��170-17�1�0-1��1�0-21521�-21721�-2��2��-2��
250-255
Colour wheelOpen/whiteDeepredDeepblueGreenOrange6000 K temperature filterUV filterWhiteDeepredDeepblueGreenOrange6000 K temperature filterUV filterForwardsrainboweffectfromfasttoslowNorotationBackwardsrainboweffectfromslowtofastRandomcolourselectionbyaudiocontrol(Setmicrophonesensitivityinmenu„Personality”)Autorandomcolourselectionfromfasttoslow
proportionalproportionalproportionalproportionalproportionalproportionalproportionalproportional
stepstepstepstepstepstep
proportionalstep
proportionalstep
proportional
8 10 30-255
CyanCyan(0-white,255-fullcyan) proportional
9 11 40-255
MagentaMagenta(0-white,255-fullmagenta) proportional
10 12 50-255
YellowYellow(0-white,255-fullyellow) proportional
11 13 60-255
Conversion temperature filter 3200K(0-5�00K,255-�200K) proportional
14
0-��-7
�-1112-151�-1�20-2�2�-272�-�1�2-�5��-���0-����-�7��-5152-555�-5��0-����-�7��-71
CMY Colour macrosNofunctionMacro1Macro2Macro�Macro�Macro5Macro�Macro7Macro�Macro�Macro10Macro11Macro12Macro1�Macro1�Macro15Macro1�Macro17
stepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstep
17
Mode / Channel 1 2 3
Value Function Type of control
14
72-757�-7��0-����-�7��-�1�2-�5��-��
100-10�10�-10710�-111112-11511�-11�120-12�12�-12712�-1�11�2-1�51��-1��1�0-1��1��-1�71��-151152-15515�-15�1�0-1��1��-1�71��-171172-17517�-17�1�0-1��1��-1�71��-1�11�2-1�51��-1��200-20�20�-20720�-211212-21521�-21�220-22�22�-22722�-2�12�2-2�52��-2��2�0-2��2��-2�72��-251252-255
Macro1�Macro1�Macro20Macro21Macro22Macro2�Macro2�Macro25Macro2�Macro27Macro2�Macro2�Macro�0Macro�1Macro�2Macro��Macro��Macro�5Macro��Macro�7Macro��Macro��Macro�0Macro�1Macro�2Macro��Macro��Macro�5Macro��Macro�7Macro��Macro��Macro50Macro51Macro52Macro5�Macro5�Macro55Macro5�Macro57Macro5�Macro5�Macro�0Macro�1Macro�2Macro��
stepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstep
12 15 0-255Effect speedFrommax.speedtomin.speed***** proportional
160-�1
�2-����-�5
��-255
Effect speed assigningDimmer + CMY filters + correction filterDimmerCMY filters + correction filterNofunction
stepstepstepstep
13 17 8
0-�10-1�1�-171�-2122-252�-2��0-��
Rotating gobo wheel 1Index - set indexing on channel(s) 14 (18,19;9,10)Open/holeGobo1-RainbowChips(150�0012)Gobo2-SunMan(150�001�)Gobo�-WaterDrops(150�001�)Gobo�-TriangleFloating(1502012�)Gobo5-Laser(1502012�)Gobo�-SwirlElectric(15020125)
stepstepstepstepstepstepstep
*****Standardspeed:Range0-255DMXatmin.speed(0DMX):Cyan(magenta/yellow)=�min,�5s
1�
Mode / Channel 1 2 3
Value Function Type of control
13 17
��-�7��-�1�2-�5��-��50-5�5�-57
5�-��70-�1�2-��
��-10510�-11711�-12�
1�0-1�11�2-15�15�-1�51��-17717�-1��1�0-201202-221222-22�22�-2��2��-2��
250-255
Rotation - set rotation on channel(s) 14 (18,19;9,10)Gobo1-RainbowChips(150�0012)Gobo2-SunMan(150�001�)Gobo�-WaterDrops(150�001�)Gobo�-TriangleFloating(1502012�)Gobo5-Laser(1502012�)Gobo�-SwirlElectric(15020125)
Shaking gobos from slow to fastIndex - set indexing on channel(s) 14 (18, 19;9,10)Gobo1-RainbowChips(150�0012)Gobo2-SunMan(150�001�)Gobo�-WaterDrops(150�001�)Gobo�-TriangleFloating(1502012�)Gobo5-Laser(1502012�)Gobo�-SwirlElectric(15020125)
Shaking gobos from slow to fastRotation - set rotation on channel(s) 14 (18,19;9,10)Gobo1-RainbowChips(150�0012)Gobo2-SunMan(150�001�)Gobo�-WaterDrops(150�001�)Gobo�-TriangleFloating(1502012�)Gobo5-Laser(1502012�)Gobo�-SwirlElectric(15020125)Forwardsgobowheel1rotationfromfasttoslowNorotationBackwardsgobowheel1rotationfromslowtofastRandomgobo1selectionbyaudiocontrol(Setmicrophonesensitivityinmenu„Personality”)Autorandomgobo1selectionfromfasttoslow
stepstepstepstepstepstep
proportionalproportionalproportionalproportionalproportionalproportional
proportionalproportionalproportionalproportionalproportionalproportionalproportional
proportionalstep
proportional
14 18 9
0-255
01-127
12�-12�1�0-255
Gobo 1 indexing and rotationGobo indexing - set position on channel 13 (17;8)GoboindexingGobo rotation - set position on channel 13 (17;8) NorotationForwardsgoborotationfromfasttoslowNorotationBackwardsgoborotationfromslowtofast
proportional
stepproportional
stepproportional
19 100-255
Gobo 1 fine indexing and rotation(set position on channel 13 (17;8))Fineindexing(rotating) proportional
15 20 11
0-�10-1�1�-171�-2122-252�-2��0-��
��-�7��-�1�2-�5��-��50-5�5�-57
5�-��70-�1�2-��
��-10510�-11711�-12�
Rotating gobo wheel 2Index - set indexing on channel(s) 16 (21, 22;12,13)Open/holeGobo1-DiamanteSpot(150�0020)Gobo2-Wheel(1502012�)Gobo�-SpaceTunel(15020127)Gobo�-Bubbles1(1502012�)Gobo5-12Dots(1502012�)Gobo�-RadialDashes(150201�0)Rotation - set rotation on channel(s) 16 (21, 22;12,13)Gobo1-DiamanteSpot(150�0020)Gobo2-Wheel(1502012�)Gobo�-SpaceTunel(15020127)Gobo�-Bubbles1(1502012�)Gobo5-12Dots(1502012�)Gobo�-RadialDashes(150201�0)Shaking gobos from slow to fastIndex - set indexing on channel(s) 16 (21, 22;12,13)Gobo1-DiamenteSpot(150�0020)Gobo2-Wheel(1502012�)Gobo�-SpaceTunel(15020127)Gobo�-Bubbles1(1502012�)Gobo5-12Dots(1502012�)Gobo�-RadialDashes(150201�0)
stepstepstepstepstepstep
stepstepstepstepstepstep
proportionalproportionalproportionalproportionalproportionalproportional
1�
Mode / Channel 1 2 3
Value Function Type of control
15 20 11
1�0-1�11�2-15�15�-1�51��-17717�-1��1�0-201202-221222-22�22�-2��2��-2��
250-255
Shaking gobos from slow to fastRotation - set rotation on channel(s) 16(21,22;12,13)Gobo1-DiamanteSpot(150�0020)Gobo2-Wheel(1502012�)Gobo�-SpaceTunel(15020127)Gobo�-Bubbless(1502012�)Gobo5-12Dots(1502012�)Gobo�-RadialDashes(150201�0)Forwardsgobowheel2rotationfromfasttoslowNorotationBackwardsgobowheel2rotationfromslowtofastRandomgobo2selectionbyaudiocontrol(Setmicrophonesensitivityinmenu„Personality”)Autorandomgobo2selectionfromfasttoslow
proportionalproportionalproportionalproportionalproportionalproportionalproportional
stepproportional
step
proportional
16 21 12
0-255
01-127
12�-12�1�0-255
Gobo 2 indexing and rotationGobo indexing - set position on channel 15 (20;11)GoboindexingGobo rotation - set position on channel 15 (20;11) NorotationForwardsgoborotationfromfasttoslowNorotationBackwardsgoborotationfromslowtofast
proportional
stepproportional
stepproportional
22 130-255
Gobo 2 fine indexing and rotation(set position on channel 15 (20))Fineindexing(rotating) proportional
17 23 14
0-1�20-���0-5��0-7��0-��
100-11�120-1��1�0-15�1�0-17�
1�0-1��1��-1�71��-1�11�2-1�51��-1��200-20�20�-20720�-211212-21521�-21�220-22�22�-22722�-2�12�2-2�52��-2��2�0-2��2��-2��250-255
Effect wheelIndex - set indexing on channel(s) 18 (24, 25;15)Open/hole�-facetprism5-facetprismEstriadoDiamanteRotation - set rotation on channel(s) 18 (24, 25;15)�-facetprism5-facetprismEstriadoDiamantePrism/gobo macrosMacro1Macro2Macro�Macro�Macro5Macro�Macro7Macro�Macro�Macro10Macro11Macro12Macro1�Macro1�Macro15Macro1�RandomEffectselectionbyaudiocontrol(Setmicroph.sensit.)AutorandomEffectselectionfromfasttoslow
stepstepstepstepstep
stepstepstepstep
stepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstep
proportional
18 24 15
0-255
01-12712�-12�1�0-255
Effect indexing and rotationEffect indexing - set position on channel 17 (23;14)EffectindexingEffect rotation - set position on channel 17 (23;14) NorotationForwardsEffectrotationfromfasttoslowNorotationBackwardsEffectrotationfromslowtofast
proportional
stepproportionalstepproportional
20
Mode / Channel 1 2 3
Value Function Type of control
250-255
Fine effect indexing and rotation(set position on channel 17 (23))Fineindexing(rotating) proportional
19 26
01-17�
1�0-1��1�0-211212-2��2��-255
FrostOpenFrostfrom0%to100%100%frostPulseclosingfromslowtofastPulseopeningfromfasttoslowRampingfromfasttoslow
stepproportionalproportionalproportionalproportionalproportional
20 27 16
01-17�
1�0-1�1
1�2-20�20�-21521�-21721�-21�220-221222-22�
22�-2��2�0-255
IrisOpenFrommax.diametertomin.diameterClosedPulse effects with Iris blackoutPulseopeningfromslowtofastPulseclosingfromfasttoslowRandompulseopening(fast)Randompulseopening(slow)Randompulseclosing(fast)Randompulseclosing(slow)Pulse effects with Iris blackout and zoomPulseopeningfromslowtofastPulseclosingfromfasttoslow
stepproportional
step
proportionalproportional
stepstepstepstep
proportionalproportional
21 28 18 0-255ZoomZoomfrommax.tomin proportional
22 29 17 0-255FocusContinuous adjustment from far to near proportional
23 30 1
0-�1�2-����-�5
��-12712�-1��1��-15�1�0-1�1
1�2-22�22�-255
Shutter, strobeShutterclosed,Lamppowerreducedto�00WShutteropen,FulllamppowerStrobe-effect from slow to fast (max.15 flashes/s)Shutteropen,Lamppowerreducedto�00WOpeningpulseinsequencesfromslowtofastClosingpulseinsequencesfromfasttoslowShutteropen,Electronicstrobing„ZAP”fromslowtofast(from 7 to 33 flashes/s)Randomstrobe-effectfromslowtofastShutteropen,Fulllamppower
stepstep
proportionalstep
proportionalproportionalproportional
proportionalstep
24 31 2 0-255Dimmer intensityDimmerintensityfrom0%to100% proportional
32 0-255Fine dimmer intensityDimmer intensity fine proportional
21
7. Controller mode The fixtures are individually addressed on a data link and connected to the controller. The fixtures respond to the DMX signalfromthecontroller.
7.1 DMX addressingThere are 512 available channels on DMX link. Every fixture on DMX link must have a DMX start address, which is defined as the first channel from which the fixture will respond to the controller.Ifyouset,forexample,fortheColorSpot2500EATthestartaddresstochannel25,theColorSpot2500EATwillusethechannels25to��forcontrol(ifMode1isselectedfrom„DMXPreseting”menu).Please, be sure that you don’t have any overlapping channels in order to control each ColorSpot 2500E AT correctly and independently from any other fixture on the DMX data link.Iftwo,threeormoreColorSpot2500EATareaddressedsimilarly,theywillworksimilarly.
Controlling:AfterhavingaddressedallColorSpot2500EAT,youmaynowstartoperatingtheseviayourlightingcontroller.Note: Afterswitchingon,theColorSpot2500EATwillautomaticallydetectwhetherDMX512dataisreceivedornot.Ifthereis no data received at the DMX-input, the display will start to flash with actually address.
7.2 Remotely controllable functions
LampTheColorSpot2500EATistobeoperatedwithaPhilipsMSRGOLD1200FastFitlamp.ArelayinsideoftheColorSpot2500EATallowsyoutoswitchonandoffthelampviathecontrolpanelorviayourDMX-controllerwithoutaffectingtherestofthelighting.Note:Itisalsoimportanttonote,thatthedischargelampiscoldrestriketypes,thatmeans,thattheyhavetobecold
beforere-striking.Forthisreason,youhavetowaitatleast5minutesafterhavingswitchedoffthelampbeforeyoucan switch it back on again. If you try to switch On the lamp within 5 minutes after having switched it Off, the fixture willstorethisinformationandautomaticallyignitethelampwhenthe5minutesperiodhasexpired.
CMY-colours mixing systemThe CMY color mixing system is based on graduated cyan, magenta, and yellow color filters. A continuous range of colors may be achieved by varying the amount of each filter from 0 to 100%.Colour temperature correction filtre lowers the colour temperature from 5600K to 3200 K.
Colour wheelThe ColorSpot 2500E AT features a colour wheel with 4 colour positions, UV filter and 6000 K temp. filter and the hole (open).Itisalsopossibletorotatethecolourwheelcontinuouslyatdifferentspeeds,theso-called„Rainboweffect“iscreated.Autorandomcolourselection,randomcolourselectionbyaudiocontrolispossible.
Rotating gobo wheel 1 Therotatinggobowheelincludes�dichroicglassgobosrotatinginbothdirectionsatdifferentspeeds.Allrotatinggobosare replaceable and fine indexable.Rotatinggobowheelcancontinuouslyrotateinbothdirectionsfromslowtofastspeed.
Rotating gobo wheel 2Therotatinggobowheelincludes1glassgoboand5dichroicglassgobosrotatinginbothdirectionsatdifferentspeeds.All rotating gobos are replaceable and fine indexable.Rotatinggobowheelcancontinuouslyrotateinbothdirectionsfromslowtofastspeed.
Effect wheelThiswheelprovides�-facetprism,5-facetprismand2glasseffectsrotatinginbothdirectionsatdifferentspeeds.Prism/gobomacrosarepossible.
IrisMotorized adjustable iris,wide range of variable pulse effects.
FrostFrost module provides variable frost for fine frosting.
Focus-multistep zoomMotorizedfocusenablesthebeamtobefocusedanywhereonstage,providedbythespecialmultistepzoomwithrange10°-�0°.
Dimmer/Shutter/StrobeSmooth0-100%dimmingisprovidedbythecombinedmechanicaldimmer/shutterunit.Thisunitmayalsobeusedforstrobe effect (1 - 15 flashes per second)
22
FansBytheControlBoardusingthe„Fan Modes”functionyoucanchoosethe2typesofthefanspeedoperatingmodes.
8. Control menu mapNote:Defaultsettings=Bold print
FixtureAddress DMXAddress 001 : 512 EthernetSettings SetEthernetMode Disable Ethernet Ethernet Ethernet/DMX SetIPAddress Default IP Address CustomIPAddress SetArtNetUniverse(0-255)Fixtureinformation PowerOnTime TotalHours ResetableHours LampOnTime TotalHours ResetableHours LampStrikes TotalHours ResetableHours Air filters SetAlertperiod(10...50....300 hours) Elapsedtime[hours]
FixtureTemperatures Current BoardTemp.[°C] AmbientTemp.[°C] NearLampTemp.[°C] MaximumNonresetable BoardTemp.[°C] AmbientTemp.[°C] NearLampTemp.[°C] MaximumResetable BoardTemp.[°C] AmbientTemp.[°C] NearLampTemp.[°C] FansSpeed Fan1 : Fan� DMXValues Pan(0-255) : DimmerFine(0-255) SoftwareVersion IC1MB IC2MB IC�MB IC�MB IC1B1 : IC1DS IC2DS ProductIDs MacAdr. RDMUID
2�
Personality UserMode UserASettings,UserBSettings,UserCSettings DMXPresetting Mode 1 Ch.1Pan : Ch.2�Dimmer SetActive Mode2 Ch.1Pan : Ch.�2DimmerFine SetActive Mode� Ch.1Shutter : Ch.2�Power SetActive PanReverse(On, Off) TiltReverse(On, Off) LampPresetting LampOn/PowerOn(On, Off) LampOffviaDMX(On, Off) LampOnifDMXPresent(On, Off) LampOffifnotDMX(On, Off) LampIgnitionDelay (0..1..90) s LampLightSensor (On, Off) Display Adjusting DisplayPermanentOn(On, Off) DisplayIntensity(1..10..15) DisplayBacklight(1..5..15) DisplayTurned(On, Off) Blackoutd.M.C.(On, Off) Pan/TiltFeedback(On, Off) MicrophoneSensitivity(1..10..20) FanModes Auto Cooling HighCooling Autofocus(On, Off) Pan/Tiltmode(Time mode, Speed Mode) ActiveBlackoutWhile Pan/TiltMoving(On, Off) ColourWheelMoving(On, Off) GoboWheelsMoving(On, Off) IRSensor(On, Off) InitEffectPositions Pan, (0..1..225) : Dimmer(0..1..255) Save DimmerCurve(Curve 1, Curve 2) CMY+CTFCurve (Curve 1, Curve 2) TemperatureUnit(°C,°F) DefaultSetting
LampOn/Off(On, Off)
Testsequences Mode1 Pan,Tilt,Zoom,Focus(0-255) RunTestProgram Mode2 RunTestProgram
2�
ManualMode PresetedEffectControl Pan(Position1,...,Position�) : Dimmer(Position1,...,Position5) ManualEffectControl Pan(0-255) : DimmerFine(0-255)
Stand-alonesetting MusicTrigger(On, Off) PresettingPlayback Disabled TestProgram Program1 Program2 Program� PlayingProgram TestProgramInLoop Program1InLoop Program2InLoop Program�InLoop EditingProgram Program1 Program2 Program� EditSteps Step1 : Step�� Pan(0-255) : Dimmer fine (0-255) StepTime(0.1-25.5s) Save Saveandcopy StartStep(1-��) EndStep(1-��) Resetfunctions ResetAll Pan/Tilt : Iris/Effect
Specialfunctions Lamp Adjustment Pan(0-255) Tilt(0-255) Zoom(0-255) Focus(0-255) Effect Adjustment DMXValues Pan(0-255) : Dimmer fine (0-255) CalibrateValues Pan(0-225) : Dimmer(0-255) Updatingsoftware SaveandReset LoadDefaultValues
25
9. Control menu Thecontrolpanelsituatedonthefrontpanelofthebaseoffersseveralfeatures.YoucansimplysettheDMXaddress,readthenumberofthelamporunithours,switchOnandOffthelamp,runtest,makearesetandalsousemanyfunc-tions for setting fixture behaviour.
Control elements on the control board:[RNS]encoderwheel-movesbetweenmenuitemsonthethesamelevel,scrollsbetweenvalues.[ESC]button-leavesmenuwithoutsavingchanges[ENTER] button-enters menu, confirms adjusted values and leaves menu After switching the fixture on, Press [ENTER], the display shows the initial screen: the display shows current address:
Themainmenuofthecontrolpanelisaccessedbypressing[ENTER]button.Tobrowsethroughthemenu,rotate[RNS] wheel.Toselectafunctionorsubmenu,press[ENTER]button.Presettedoptionsaredisplayednegative.
9.1 Fixture Address UsethismenutosettheDMXaddress.
DMX Address -SelectthissubmenutosetDMXstartaddress.Ethernet Settings - Select this submenu to set the fixture for Ethernet operating. Set Ethernet Mode -SelectthissubmenutoselectEthernetoperatingmode: Disable Ethernet -disablesnetworkoperating. Ethernet -Data are received to the Ethernet input of the fixture - every fixture from fixture chain has to
beconnectedtothenetwork. Ethernet/DMX -Data go from Ethernet input „through” the fixture to the DMX output of the fixture- it is
possible to connect the next fixture to DMX output and to make a DMX chain. Set IP Address -SelectthissubmenutosetIPaddress.IPaddressistheInternetprotocoladdress.
The IP uniquely identifies any node (fixture) on a network. There can't be 2 fixtures with the sameIPaddressonthenetwork!
Default IP Address - Presetted IP address, you can edit only first number of IP address (2 or 10)e.g.002.01�.052.0��.
Custom IP Address -TheoptionenableseditallnumbersofIPaddresse.g.002.019.052.086.TosetthecustomIPaddress:
1.Select„CustomIPAddress”andpress[ENTER]. 2. Use RNS wheel to set the first number of IP addres �.Press[ENTER]tomoveonthesecondnumberofIPaddress �.Repeatsteps2and�forthethirdandthefourthnumberofIPaddress. Ifyouwanttoreturnbackontheprevioulyedittednumber,press[ESC]. Set ArtNet Universe -SelectthissubmenutosetaUniverse(0-255).TheUniverseisasingleDMX512frame
of512channels.
9.2 Fixture informationUse this menu to read an useful information about the fixture.Power On Time -Selectthissubmenutoreadthenumberofoperationhours. Total Hours -Thefunctionshowsthetotalnumberoftheoperationhourssince theColorSpot2500EAThasbeenfabricated. Resetable Hours-Thefunctionshowsthenumberoftheoperationhoursthat theColorSpot2500EAThasbeenpoweredonsincethecounterwaslastreset.Inordertoreset thiscounterto0,press[ENTER]twice.Lamp On Time-Selectthissubmenutoreadthenumberoftheoperationhourswiththelampon. Total Hours -Thefunctionshowsthetotalnumberoftheoperationhourswiththelamponsince theColorSpot2500EAThasbeenfabricated. Resetable Hours-Thefunctionshowsthenumberoftheoperationhourswiththelamponthat theColorSpot2500EAThasbeenpoweredonsincethecounterwaslastreset.Inordertoreset thiscounterto0,press[ENTER]twice.Lamp Strikes-Selectthissubmenutoreadthetotalnumberofthelampstrikes. Total Hours -Thefunctionshowsthetotalnumberofthelampstrikessince theColorSpot2500EAThasbeenfabricated. Resetable Hours-Thefunctionshowsthenumberofthelampstrikessincethecounterwaslastreset. Inordertoresetthiscounterto0,press[ENTER]twice.
2�
Air Filters --- Regular cleaning of the air filters is very important for the fixture´s life and performance.Bildup of dust,dirt and fog fluid residues reduces the fixture´s light output and cooling ability.The two items of this menu help you to keep cleaning peeriod of the air filters. Set alert period - Cleaning schedule for the fixture depends on the operating enviroment. Itisthereforeimposibletospecifyaccuratecleaninginterval.Thisfunctionallows you to change the cleaning interval of the air filters.This "alert" value is 50 hours and it is set as default.Inspect the fixture within its 50 hours of operation to see whether cleaning is necessary.If clening is required,clean all air filters and change the value in this menu onacceptablelevel.Min.levelofalertperiodis10hours,max.is�00hours. Elapsed Time - The option allows you to read the time which remains to cleaning air filters. Thetimeperiodissetinthemenumentionedabove. Expiredtimeperiodissignalizedbyanegativemarkatthetimevalueandawarningicon (triangle) on the display with the following message: "Clean Air Filters" Clean the filters and reset this menu item (by pressing "Enter" button twice while this menu ishighlighted)tostartthenewtimecountdown.
Fixture Temperatures - Select this submenu to read the temperatures of the fixture: Current - Select this function to read the current temperatures of the fixture inside (Board Temp.,AmbientTemp.,NearLampTemp.) Maximum nonresetable -The function shows the max.temperatures of the fixture inside (Board Temp., Ambient Temp.,NearLampTemp.)sincetheColorSpot2500EAThasbeenfabricated. Maximum resetable- The function shows the maximum temperatures of the fixture inside (Board Temp., Ambient Temp.,NearLampTemp.)sincetherespectivecounterwaslastreset.Inordertoresetdesiredcounterto 0,press[ENTER]twice. Measurementpoints: Board Temp. - temperature on the main board in the fixture base. Ambient Temp.-temperature of the air which is sucked to the fixture base. This temperature can be different from the real ambient temperature due to e.g. suction of the hot air from the fixture head to the base if the fixture ishangingattheceiling.Pleasenotethattheambienttemperatureshouldnotexceed�5°C. Near Lamp Temp.-temperatureinthelampchamber.
Fans Speed-Selectthisfunctiontoreadtheactualspeedofthefans(revolutionsperminute): Fan1 -Thefancoolsthelamppeak Fan 3 -Thefanontherearleftsideofthehead Fan 5 -TheleftfanattheCMYmodule Fan 6 -TherightfanattheCMYmodule Fan 7 -TheFanisidethehead Fan 9 -Thefanonthefrontrightsideofthehead
Location of the fans: (Top view)
27
DMX Values - Select this function to read DMX values of each channel received by the fixture.
Product IDs-SelectthisfunctiontoreadtheMACaddressortheRDMUIDnumber.Software Version - Select this function to read the software version of the fixture modules: IC1 MB - Main processor on the main board in the fixture base IC2 MB - Tilt processor on the main board in the fixture base IC3 MB - Pan procesor on the main board in the fixture base IC4 MB - EEprom on the main board in the fixture base IC1 B1 - Shutter/conversion filter 3200K processor on the board 1 in the fixture head IC2 B1 - Gobo wheel 1/gobo rotation/colour wheel processor on the board 1 in the fixture head IC3 B1 - Effect wheel/effect rotation processor on the board 1 in the fixture head IC4 B1 - CMY processor on the board 1 in the fixture head IC1 B2 - Zoom/focus/frost processor on the board 2 in the fixture head IC2 B2 - Gobo wheel 2/gobo rotation/iris processor on the board 2 in the fixture head IC1 DS - Display processor on the display module in the fixture base IC2 DS - Memory on the display module in the fixture base
Location of the fans, processors and temperature measuring points:(Top view)
Display module
(Rear view)
9.3 PersonalityUsethismenutotomodifyColorSpot2500EAToperatingbehavior.
User mode -ColorSpot 2500E AT allows you to recall up to 3 user settings. After switching the fixture on for the first time, theUser A settingsareactive.Allchangesmadein„Personality”menu,„FixtureAddress”menuandMusic TriggerandPresettingPlaybackfunctionsfrom„Stand-alonesetting”menuaresavedtotheUser A settings.If younowsettheUser B settingsactive,fromthismomentthesechangesaresavedtothe User B settings. After switching the fixture off and on, the User B setting is active. In this way you may use 3 fixture operating behaviour. User A Settings -ThefunctionrecalltheuserAsettings. User B Settings -ThefunctionrecalltheuserBsettings. User C Settings -ThefunctionrecalltheuserCsettings.
Pan Reverse-Selectthisfunctiontoinvertthepanmovement.
Tilt Reverse-Selectthisfunctiontoinvertthetiltmovement.
DMX Preseting-Selectthisfunctiontosetdesiredeffectsassigningtothechannels.Youcanchoose2effectsorders (Mode1-2�channels,Mode2-�2chanels,Mode�-2�channels).
2�
Mode 1 - Default channel setting:Channel Effect Channel Effect
1 Pan 13 GoboWheel1
2 PanFine 14 Gobo1Indexing
3 Tilt 15 GoboWheel2
4 TiltFine 16 Gobo2Indexing
5 Pan/TiltSpeed 17 EffectWheel
6 Spec.Func. 18 EffectIndexing
7 Colour Wheel 19 Frost
8 Cyan 20 Iris
9 Magenta 21 Zoom
10 Yellow 22 Focus
11 ConversionFilter 23 Shutter/Strobe
12 EffectSpeed 24 Dimmer
Mode 2Channel Effect Channel Effect
1 Pan 17 GoboWheel1
2 PanFine 18 Gobo1Indexing
3 Tilt 19 Gobo1F.Indexing
4 TiltFine 20 GoboWheel2
5 Pan/TiltSpeed 21 Gobo2Indexing
6 SpecialFunctions 22 Gobo2F.Indexing
7 Pan/TiltMacro 23 EffectWheel
8 P./T.MacroSpeed 24 EffectIndexing
9 ColourWheel 25 EffectF.Index.
10 Cyan 26 Frost
11 Magenta 27 Iris
12 Yellow 28 Zoom
13 ConversionFilter 29 Focus
14 CMYColourMacro 30 Shutter/Strobe
15 EffectSpeed 31 Dimmer
16 EffectSpdAssig. 32 DimmerFine
Mode 3Channel Effect Channel Effect
1 Shutter/Strobe 13 Gobo2F.Indexing
2 Dimmer 14 EffectWheel
3 Cyan 15 EffectIndexing
4 Magenta 16 Iris
5 Yellow 17 Focus
6 ConversionFilter 18 Zoom
7 Colour Wheel 19 Pan
8 GoboWheel1 20 PanFine
9 Gobo1Indexing 21 Tilt
10 Gobo1F.Indexing 22 TiltFine
11 GoboWheel2 23 Pan/TiltSpeed
12 Gobo2Indexing 24 Spec.Func.Pleaserefertothechapter“DMX-protocol”fordetaildescription.
2�
Lamp Presetting-Selectthismenutochangethelamp„behaviour”. Lamp On/Power On - Select this function to turn the lamp on automatically after switching the fixture on. Lamp Off via DMX-SelectthisfunctiontoswitchoffthelampviaDMX. Lamp On if DMX Present-Thisfunctionallowsyoutostrikethelampautomaticallyafter2�secondsifDMX signal is present on the data link.If the ignition is unsuccessfull (e.g.lamp is too hot), the fixture will try to ignite thelampafternext2�s.Thisprocesswillrepeatuntilthelamplights. Lamp Off if not DMX-ThisfunctionallowsyoutoswitchOffthelampautomaticallyafter2minutesifDMXsignal ismissingonthedatalink. Lamp Ignition Delay-Thisfunctionallowsyoutosetthetimedelay(0-�0s)beforethelampwillbeignited.This setting will not affect starting the lamp direct from the control panel (menu "Lamp On/Off").Lamp Light Sensor-Selectthisfunctiontoswitchthelamplightsensoronoroff.Theoption„On”isforthestandardoperation.Important: Theoption„Off” isfor„emergencyoperation”onlyifthelamplightsensorisdefectiveandyouwillwaitforaserviceintervertion!Ifthelamplightsensorisswitchedoffandatswitchingthelampontheelectronicswillstilltrytoignitethelampuntilitshines(evenwhenthelampisdamagedorabsent),onthisaccountsomeelectronicspartscouldbedamaged!
Display Adjusting-Thisfunctionallowsyoutochangethedisplaysettings. Display Permanent On-Thisfunctionallowsyoutokeepthedisplayonortoturnoffautomatically2minutes afterlastpressinganybutton(orawheelmovement)onthecontrolpanel. Display Intensity- Select this function to adjust the display intensity (1-min.,10-max.). Display Backlight - Select this function to adjust the display backlight (1-min.,10-max.). Display Turned-Selectthisfunctiontoturnthedisplayby1�0°.
Blackout d.M.C.-Selectthisfunctiontoenabletheblackoutduringtheheadmovementcorrection(ifthemovinghead lostitsrightpan/tiltpositionforashortmoment).
Pan/Tilt Feedback-Thisfunctionallowstoreturnthemowingheadtotherequiredpan/tiltpositionafterchangingthe positionbyexternalforce(e.g.bystroke).Be careful, the Pan/Tilt Feedback OFF is not the standard operation and the head of the fixture can be demaged! Note: Ifthefeedbackwasswitchedoff,thepan/tilt-positionischangedbyanexternalforceandthefeedbackisswitched onagain,themovingheadmightnottobesynchronizedwiththeDMXsignal.Youhavetomakearesetinorder tosynchronizethemovingheadwiththeDMXsignal.
Microphone Sensitivity - Select this function to adjust the microphone sensitivity from 1(maximum) to 20 (minimum). If the sensitivity is correctly adjusted, the mark willappear(blinkinginthebassbeat.)
Fan Modes-Byusingthisfunctionyoucanchoose2typesofthefanspeedoperatingmodes. Auto Cooling -Thefansautomaticallyraisetheirspeedinordertocontrolinsidetemperatureofthelighting, ifthetemperatureinsideincreasesaboutcertainlevel(thelowfanspeedreducesthecoolingofthelighting). Thiscyclecanrepeatseveraltimesuntilthetemperatureinsideisonasuitablelevel. High Cooling-Thecoolingfansworkonmax.speed(max.cooling).Thismodewerecommendforhighambient temperature(�0°Candmore).
Autofocus-Thefunctionimprovestheimageonthewallifthezoomchanges(itseffectisthebestforgobosfromgobo wheel2andfordistancecca�m).Ifyouwanttofocustheimageonthelongdistance(morethan15m),this functionshouldbesetoff.
Pan/Tilt mode-Usethismenutosetthecharacterofthepan/tiltmovement. Time mode -Panandtiltwillmovewithdifferentspeedsandtheywillcomeatthesametimetoendpoint(pan andtiltsetsitsoptimalspeed). Speed Mode - Pan and tilt will move with the same speed as adjusted by the channel 5 (Pan/Tilt speed). E.g. panwillcometotheendpointandwaitfortilt,whichhaslongertrack.
Active Blackout while:-Usethisfunctionifyouwishtoclosethelightoutputduringeffectchanges. Pan/Tilt Moving -Thisfunctionclosesthelightoutputduringpan/tiltchanges. Colour Wheel Moving -Thisfunctionclosesthelightoutputduringcolourchanges. Gobo Wheels Moving -Thisfunctionclosesthelightoutputduringgobowheel1/gobowheel2changes.
IR Sensor-Selectthisfunctiontoswitchon/offinfra-redremotecontrol.
Init Effect Positions - Select this function to set all effects to the desired positions. After switching the fixture on (if DMX isnotconnected),alleffectswillmovetothisinitpositions.Note: If you operate 24 channels pre-setting (Mode 1) and you adjust DMX values for channels which are not included in this mode, you will not be able to change these effects from the controller !For example: You operate the Mode 1 and in „Init Effect Positions” menu is adjusted CMY Colour Macro =150, thisvalue shoudbe0oryouwillnotabbletocontrolcyan,magentaandyellowbecausetheseeffectsareusedinCMY macrosandthemacroshaveapriority.
�0
Dimmer Curve-Selectdesireddimmerrunning.
Curve1 Curve2
CMY + CTF Curve - Select desired CMY filters + conversion temperature filter running.
Curve1 Curve2
Temperature Unit --- Select this menu in order to display fixture temperatures in °C or °F.
Default Settings - Select this option to reset all fixture personalities to the default values.
9.4 Lamp On/OffUsethisoptioninordertoswitchon/offthelamp.Itisalsoimportanttonote,thatthelampiscoldrestriketype,thatmeans,thatithastobecoldbeforestriking.
9.5 Test sequencesUsethismenutotorunaspecialdemo-testsequenceswithoutanexternalcontroller,whichwillshowyousomepossibili-tiesofusingColorSpot2500EAT. Mode1 - This mode is suitable for projections on the wall, ceiling or ground without any head movement. Mode2-ThismodeusesallColorSpot2500EATfunctionsincludingpan/tiltmovementandthereforeis goodfor a complete introduction of the fixture.
9.6 Manual mode Presetted Effects - Selectthismenutocalluppresettedpositionsofchanneleffects.Manual Effect control - Selectthismenutocontrolchannelsbycontrolelementsonthecontrolboard.
9.7 Stand-alone settingUsethismenutosetoptionsforstand-alonemodeasaselectionoftheplayingprogram,programmingandmodifyingcurrentprograms. Music Trigger-Selectthisfunctiontoenablethesoundcontroloftherunningprogramsviathebuilt-inmicrophone. Presetting Playback-Thisfunctionallowsyoutoselecttheprogramwhichwillbeplayedinthe stand-alone mode after switching the fixture on.Selected program will be played continuously in a loop. Disabled-Theoptiondisables„Presettingplayback”function. Test Program-Theoptionwillstartbuilt-intestprogram. Program 1-TheoptionwillstartcreatedprogramNo.1 Program 2-TheoptionwillstartcreatedprogramNo.2 Program 3-TheoptionwillstartcreatedprogramNo.�Note: If the fixture operates in the controller mode (DMX controller is connected) and any program from this menu is selected, in this case the fixture will not respond to the DMX controller after switching on and will play selected program. Playing program-Selectthismenutorunabuilt-inprogramorthe�freely-programmableprogramsinaloop. Test Program In Loop-Theoptionstartsbuilt-intestprogram. Program 1 In Loop-TheoptionstartscreatedprogramNo.1 Program 2In Loop -TheoptionstartscreatedprogramNo.2
�1
Program 3 In Loop-TheoptionstartscreatedprogramNo.�Selecttheprogramyouwishandpress[ENTER].Theselectedprogramstartsrunning.ByPressing[ENTER]againispossibletopausetheprogramrunning.
Editing Program-Selectthismenutoeditorcreatetheprogram.TheColorSpot2500EAThasonebuilt-inprogramandthe�freeprograms,eachupto��steps.Eachprogramstephasasteptime.Steptime-thetime,duringwhicheffectslastinthecurrentstep.Procedure:1.Selecttheprogramyouwanttoedit(„Program1”-„Program�”)andpress[ENTER].2.Select„EditSteps”menuandpress[ENTER].�.Selectthedesiredprogramstep(„Step01”-„Step��”)andpress[ENTER].�Selectthedesireditemandpress[ENTER].NowyoucaneditDMXvalueforselecteditem: "Pan"-acoarsepan,value0-255 "Pan Fine" - a fine pan, value 0-255 "Tilt"-acoarsetilt,value0-255 "Tilt Fine" - a fine tilt, value 0-255 "Pan/Tilt Speed "-aspeedofpan/tiltmovement,value0-255 "Spec. Func."-aspecialfunctions,lampon/off,reset,value0-255 "Pan/Tilt Macro"-apan/tiltmacro,value0-255 "P./T.Macro Speed"-apan/tiltmacrospeed,value0-255 "Colour Wheel"-acolourwheel,value0-255 "Cyan"-acyan,value0-255 "Magenta"-amagenta,value0-255 "Yelow" - anyellow,value0-255 "Conversion Filter" - a conversion temperature filter, value 0-255 "CMY Colour Macro" - aCMYcolourmacro,value0-255 "Effect Speed" - aeffectspeed,value0-255 "Effect Speed. Assig." - aeffectspeedassigning,value0-255 "Gobo Wheel 1" - arotatinggobowheel1,value0-255 "Gobo 1 Indexing" - agobo1-coarseindexingandrotation,value0-255 "Gobo 1 F. Indexing " - a gobo 1 - fine indexing and rotation, value 0-255 "Gobo Wheel 2" - arotatinggobowheel2,value0-255 "Gobo 2 Indexing" - agobo2-coarseindexingandrotation,value0-255 "Gobo 2 F. Indexing " - a gobo 2 - fine indexing and rotation, value 0-255 "Effect Wheel " - aneffectwheelandprism/gobomacro,value0-255 "Effect Indexing" -aneffect-coarseindexingandrotation,value0-255 "Effect F. Index. " - an effect - fine indexing and rotation, value 0-255 "Frost" -afrost,value0-255 "Iris" - aniris,value0-255 "Zoom" - azoom,value0-255 "Focus" - afocus,value0-255 "Shutter/Strobe" - ashutterandstrobe,value0-255 "Dimmer" - adimmerintensity-coarse,value0-255 "Dimmer Fine" - a dimmer intensity-fine, value 0-255 5. Select „Save” or „Save and Copy” and press [Enter] to confirm adjusted values: "Save" - savingthecurrentprog.step "Save and Copy" - savingandcopyingthecurrentprog.steptothenextprog.step.�.Goonnextprog.stepandrepeatthisprocedure(steps�and5).Aftercreationtheprogram,youcansimplyreduceditslength(bychangingthestart/endsteps)usingthe„StartStep”and„EndStep”menu.
9.8 Reset functionsTheColorSpot2500EATcanberesettotallyorbyfunctionmodules.Selectrelevantfunctiontorunareset:Reset All - This function enables the fixture to index all effects and return to their standard positions.Pan/Tilt-Thisfunctionresetspanandtilt.Colour System - This function resets colour wheel and CMY/conversion filter module.Gobo System-Thisfunctionresetsbothrotatinggobowheels1and2.Dimmer/Strobe-Thisfunctionresetsdimmer/strobemodule.Focus/Zoom/Frost-Thisfunctionresetsfocus,zoomandfrost.Iris/Effect-Thisfunctionresetsirisandeffectwheel.
9.9 Special functionsUse this menu for special services like adjusting lamp or adjusting effects. Lamp Adjustment - This function can be used when you make the fine adjustment of the lamp. If you select this function, alleffectswillbecanceled,shutterwillbeopenedandthedimmerintensitywillbesetonto100%.Byusingthe options„PAn, Tilt, Zoom, Focus” you can focus the light on a flat surface (wall) and perform the fine lamp
�2
adjustment.Effect Adjustment - By this function you can calibrate and adjust the effects to their standard/right positions. Disconnect the DMX controller from the fixture and select „DMX Values”menu.Thedisplayshowsstepbystepeffectsby which you can adjust the fixture to the required position before the function calibration. When the positioning is finished, select „Calibrate Values”andpress[ENTER]:1. Calibration via the control boardSelect desired effect, press [ENTER] and adjust its right value (0 - 255). This can be repeated for each calibred effect if it is required. When the calibration is finished, it is necessary to use the „Save and Reset”functiontowritethecalibrationvalues to the memory and to make a reset in order to check the newly adjusted positions of the calibrated effects.List of the calibrated effects: Pan Yellow Gobo2Indexing Tilt ConversionFilter EffectWheel ColourWheel GoboWheel1 EffectIndexing Cyan Gobo1Indexing Iris Magenta GoboWheel2 Dimmer
2. Calibration via the DMX controllerConnect the DMX controller to the fixture. Select desired effect and press [ENTER]. Now you can calibrate the selected effectbyyourcontroller.DMXcalibrationprotocolforMode1andMode�(2�controlchannels): Pan...................channel25 Yellow...................channel�0 Gobo2Indexing.....channel�5 Tilt....................channel2� ConversionFilter...channel�1 EffectWheel...........channel�� ColourWheel...channel27 GoboWheel1.......channel�2 EffectIndexing........channel�7 Cyan.............channel2� Gobo1Indexing....channel�� Iris..........................channel�� Magenta........channel2� GoboWheel2.......channel�� Dimmer...................channel��
DMXcalibrationprotocolforMode2(�2controlchannels): Pan..................channel�� Yellow....................channel�� Gobo2Indexing.....channel�� Tilt....................channel�� ConversionFilter...channel�� EffectWheel...........channel�� ColourWheel...channel�5 GoboWheel1.......channel�0 EffectIndexing........channel�5 Cyan................channel�� Gobo1Indexing....channel�1 Iris...........................channel�� Magenta...........channel�7 GoboWheel2.......channel�2 Dimmer...................channel�7Afterhavingcalibratedrequiredeffects,usethe„Save and Reset”functiontowritethecalibrationvaluestothememoryand to make a reset in order to check the newly adjusted positions of the calibrated effects.Item„Load Default Values”enablestoloaddefaultfactorycalibrationvalues.
Updating software - This option is available in the fixture with software version 3.0 or higher.Using this function you can update software in the fixture via PC and serial link.Thefollowingarerequiredinordertoupdatesoftware:-PCrunningWindows�5/��/2000/XPorLinux-DMXSoftwareUploader-FlashcableRS2�2/DMX(No.1�050�2�)
Note1:Software update should execute a qualified person.If you lack qualification, do not attempt the updateyourselfandaskforhelpyourROBEdistributor.Note 2:DMXaddress,IPaddress,programs1-�andallfunctionsinmenuPersonalitywillbesettotheirdefaultvalues.
To update software in the fixture:1.InstallationofDMXSoftwareUploader. 1.DMXSoftwareUploaderprogramisavailablefromtheROBEwebsiteatWWW.robe.cz. 2.Makeanewdirectory(e.g.Robe_Uploader)onyourharddiskanddownloadthesoftwaretoit. 3.Unpack the program from the archive. Program file has name:DSU_name of corresponding fixture_SoftwareID.If the Robe fixture is produced in magnetic and electronic ballast version, name of DMX Software Uploader is the same for both versions.SoftwareID describes the versions of fixture softwareincludedinDMXSoftwareUploader.Highernumbermeanslatersoftwareversions.2.Fixturesoftwareupdating. 1.DeterminewhichofyourCOMportisavailableonyourPCandconnectitwithtotheDMXinputofthe fixture using the Flash cable. Do not extend this cable! Disconnect the fixture from the other fixtures in DMX chain! Turn on the computer and the fixture. Make sure that the lamp is switched off. 2.Switch the fixture to the update mode by selecting the option Updating Software in menu Special Functions on the fixture control panel.(From this option you cannot return back to the main menu. If you do not want to continue in software update, you have to switch off and on the fixture to leave this option!) 3.ItisrecommendedthatyouexitallprogramsbeforerunningthisSoftwareUploader. 4.StarttheSoftwareUploaderprogram.SelectdesiredCOMandthenclickConnectbutton. IftheconectionisOK,clickStartUploadingbuttontostartuploading.Itwilltakeseveralminutestoperform software update.If the option "Incremental Update"isn´t checked ,all processors will be updated (including processorswiththesamesoftwareversion). Ifyouwishtoupdateonlylaterversionsofprocessors,enabletheIncrementalUpdatecheckbox. Avoidinterruptingtheprocess.Updatestatusisbeingdisplayedinthelistwindow. When the update is finished, the line with the text “The fixture is successfuly updated‘ will appear in this
��
window and the fixture will reset with the new software.Note: In the case of interruption of the upload process (e.g. power cut), the fixture remains in the update mode and you havetorepeatthesoftwareupdateagain.For example: The fixture was switched off before finishing software upload. After switching the fixture on again, the fixture isstillintheupdatemodeandthedisplayisdark.RestarttheSoftwareUploaderprogramandrepeatsoftwareupdatefromyourPC.
10. Power down modeThis mode omits fixture reset after switching the fixture on and reduses motor powers of the fixture. „Power down mode” is useful in special casech.g. if the fixture is in a flight case and you want to set its DMX address without taking it out from thecase.Toenter„Powerdownmode”:Pressandhold[ENTER]andatthesametimeswitchonthePowerswitch.Thefollowingmessageappears: RealySkipInitialReset? Escape/EnterPress [ENTER] to activate „Power down mode” without fixture reset.Now you can set features and behaviour of the fixture by using „Fixture Address” menu and „Personality” menu.It is expected,that this mode will be exited by switching the fixture off, but if you want to go directly to „normal operation mode”, execute any fixture reset.Note: Allmotorsin„Powerdownmode”aredeactivatedandswitchingthelamponfromthecontrolpanelisblocked.
11. RDMThis fixture supports an RDM operation. The RDM(RemoteDeviceManagement)isabi-directionalcommunicationsprotocolforuseinDMX512controlsystems,itisthenewopenstandardforDMX512 device configuration and status monitoring.TheRDMprotocolallowsdatapacketstobeinsertedintoaDMX512datastreamwithoutadverselyaffectingexistingnon-RDM equipment. By using a special „Start Code,“ and by complying with the timing specifications for DMX512, the RDM protocol allows a console or dedicated RDM controller to send commands to and receive messages from specific movinglights.
TheROBEDreamBoxwithanadditionalROBERDM-networksoftwareprovidestheRDMfunctionality.TheDreamBoxsupportsRDM-newcontrolprotocolfeaturingAutoPatchandFixtureStatusMonitoring.
ThelistofRDMcommandsfortheColorSpot2500EATisthefollowing:
Parameter ID Discovery command SET command GET commandDISC_UNIQUE_BRANCH *DISC_MUTE *DISC_UN_MUTE *
DEVICE_INFO *
SUPPORTED_PARAMETERS *
SOFTWARE_VERSION_LABEL *
DMX_START_ADDRESS * *
IDENTIFY_DEVICE * *
DEVICE_MODEL_DESCRIPTION *
MANUFACTURER_LABEL *
DEVICE_LABEL * *
SENSOR_DEFINITION *
SENSOR_VALUE *
DISPLAY_INVERT * *
DISPLAY_LEVEL * *
PAN_INVERT * *
TILT_INVERT * *
DEVICE_RESET *
DMX_PERSONALITY * *
DMX_PERSONALITY_DESCRIPTION *
STATUS_MESSAGES *
STATUS_ID_DESCRIPTION *
LAMP_STATE * *
��
LAMP_ON_MODE1 * *
DEVICE_HOURS2 *
LAMP_HOURS 2 *
LAMP_STRIKES2 *
1...Another options for this command (only for Robe´s fixtures): valuePARAMETER_DATA=0x��-lampOFFbyDMXvalueonDMXchannel valuePARAMETER_DATA=0x��-lampOFFifDMXisnotpresent2...Commandsrelativeresetablevalues
12. Error and information messagesOccured errors during fixture operation are signalized by warning icon on the display:
Press[ESC]toseethecurrenterrormessages.
Description of the error messages:
Active Lamp Timer Thismessageappearsifyoutrytoswitchonthelampwithin5minutesafterhavingswitcheditoff(thelampistoohot).The message will appear on the display if the lamp doesn't ignite within 28 seconds. The ColorSpot 2500E AT will store thisinformationandautomaticallyignitethelampwhenthe5minutesperiodhasexpired.Caution:Themessageisdisabledifthelamplightsensor(function„LampSensor”inmenuPersonality)isswitchedOff.
Lamp ErrorThe ignition of the lamp is seven times unsuccessful (the "Active Lamp Timer" message appeared six times before), and thedisplayshows"Lamp Error",meaningthatthelampcouldbedamagedorevenmissedortherecouldbeafailureontheignitororballast.Pleaseplaceorreplacethelampandcontactyourdealerifthesituationwasnotcausedbythelamp.Caution:Themessageisdisabledifthelamplightsensor(function„LampSensor”inmenuPersonality)isswitchedoff.
Overheated ->Lamp lowThis message informs that the fixture head is overheated and the lamp power was reduced to 700 W.After 10 minutes the lamppowerwillbeswitchedtothefullpower.
Overheated ->Lamp OffThis message informs that the fixture head is overheated and the lamp was switched off by its temperature sensor.
Lamp Sensor ErrorThismessageinformsthelamplightsensorisfailed.Caution:Themessageisdisabledifthelampsensor(functionLampSensorinmenuPersonality)isswitchedoff.
Short Power ErrorThis message will appear if the fixture was shortly disconnect from the main.
Supply Frequency ErrorThismessagewillappearifthefrequencyofthemainisnotstandard50or�0Hz.Thismessagecanappearasaresultoftheinterferenceduringthelampstarting(ifthelamporigniterisold)orasaresultoftheinterferencebyneighbouringdevices.In these cases the message does not affect the fixture operating! Thefollowingerrormessagesareseparatedinto2groups:xxxx xxxx Error 1(e.g.Colour Wheel Error 1,Gobo2IndexError1)xxxx xxxx Error 2 (e.g.ColourWheelError2,Gobo2IndexError2)Therearesomepossiblereasonsoffaults:Message Characteristic faultxxxx xxxx Error 1 MagneticsensorispermanentlyOn(e.g.leadingwireisshort- circulated,defectivesteppingmotor,defectivecontrolcircuitonthePCB) xxxx xxxx Error 1/xxxx xxxx Error 2 MagneticsensorispermanentlyOff(e.g.leadingwireisdisconnected,(together) defectivemagneticsensor,missingmagnet),defectivesteppingmotor.
�5
Colour Wheel Error 1 (Colour Wheel Error 2)Themessageswillappearaftertheresetofthecolourwheelifthiswheelisnotlocatedinthedefaultposition.
Gobo 1 Wheel Error 1 (Gobo 1 Wheel Error 2)Themessageswillappearaftertheresetofthegobowheel1ifthiswheelisnotlocatedinthedefaultposition.
Gobo 1 Index Error 1 (Gobo 1 Index Error 2)Themessageswillappearaftertheresetofthegobowheel1iftherotatinggobowheelsarenotlocatedinthedefaultpositions.
Gobo 2 Wheel Error 1 (Gobo 2 Wheel Error 2)Themessageswillappearaftertheresetofthegobowheel2ifthiswheelisnotlocatedinthedefaultposition.
Gobo 2 Index Error 1 (Gobo 2 Index Error 2)Themessageswillappearaftertheresetofthegobowheel2iftherotatinggobowheelsarenotlocatedinthedefaultpositions.
Effect Wheel Error 1 (Effect Wheel Error 2)Themessageswillappearaftertheresetoftheeffectwheelifthiswheelisnotlocatedinthedefaultposition.
Effect Index Error 1 (Effect Index Error 2)Themessageswillappearaftertheresetoftheeffectwheeliftherotatingeffectwheelsarenotlocatedinthedefaultpositions.
Iris Error 1 (Iris Error 2)Themessageswillappearaftertheresetoftheirisiftheirislamellasarenotlocatedinthedefaultpositions.
Cyan Lamella Error 1 (Cyan Lamella Error 2)ThemessageswillappearaftertheresetoftheCMYmoduleifthecyanlamellasarenotlocatedinthedefaultpositions.
Magenta Lamella Error 1 (Magenta Lamella Error 2)ThemessageswillappearaftertheresetoftheCMYmoduleifthemagentalamellasarenotlocatedinthedefaultpositions.
Yellow Lamella Error 1 (Yellow Lamella Error 2)ThemessageswillappearaftertheresetoftheCMYmoduleiftheyellowlamellasarenotlocatedinthedefaultpositions.
CTO Lamella Error 1 (CTO Lamella Error 2)ThemessageswillappearaftertheresetoftheCTOmoduleiftheCTOlamellasarenotlocatedinthedefaultpositions.
Zoom Error 1 (Zoom Error 2)Themessageswillappearaftertheresetofthezoommoduleifthemoduleisnotlocatedinthedefaultposition.
Focus Error 1 (Focus Error 2)Themessageswillappearaftertheresetofthefocusmoduleifthemoduleisnotlocatedinthedefaultposition.
Pan Error 1 (Pan Error 2)Themessageswillappearaftertheresetoftheyokeiftheyokeisnotlocatedinthedefaultposition.
Tilt Error 1 (Tilt Error 2)Themessageswillappearaftertheresetoftheheadiftheheadisnotlocatedinthedefaultposition.
13. Technical specifications
Power supply: Voltage:........................................20�/2�0/250VAC,50/�0Hz~ Mainfuses: Livefuse:.........T15A@2�0V Neutralfuse:....T15A@2�0V Powerconsumption:.....................17�0VA
Lamp: PhilipsMSRGOLD1200FastFit;��00K;1�00W;750hrslife,PGJX50
��
Optical System: - High luminous-efficiency parabolic reflector -Focuslensandmultistepzoomlensessystem -Beamangle:10°-�0° - All lenses are anti-reflection coated
CMY-colours mixing module -SmoothCMYcolourmixingsystem - Colour temperature correction filtre lowers the colour temperature from 5600K to 3200 K -��colourmacros
Colour wheel - 4 dichroic filters, UV filter, 6000K temp. filter plus white -Colourwheelwithvariablerotationspeedinbothdirections -Randomcolourselectionbyaudiocontrol -Autorandomcolourselection
Rotating gobo wheel 1 -�replaceabledichroicglassgobosplusanopenpositionrotatinginbothdirectionsatdifferentspeeds -Finegoboindexingandrotation -Rotatinggobo-wheelcont.rotation -Shakinggoboswithvariablespeed -Randomgoboselectionbyaudio -Autorandomgoboselection -Dichroicglassgobos:outsidediameter=�7.�mm,imagediameter=�1.5mm, high temperature borofloat or better glass, thickness=1.1mm up to 5 mm, coating: dichroicorenhancedaluminium
Rotating gobo wheel 2 -�replaceablegobos(1glassgobo,5dicroicglassgobosplusanopenposition) rotatinginbothdirectionsatdifferentspeeds -Finegoboindexingandrotation -Rotatinggobo-wheelcont.rotation -Shakinggoboswithvariablespeed -Randomgoboselectionbyaudio -Autorandomgoboselection -Rotatinggobo-wheelcont.rotation -Dichroicglassgobos:outsidediameter=�7,�mm,maximumimagediameter=�1.5mm, high temperature borofloat or better glass, thickness=1.1mm up to 5mm, coating: dichroicorenhancedaluminium-Glassgobo:outsidediameter=�7mm, high temperature borofloat or better glass, thickness=1.1mm up to 5 mm
Effect wheel -�-facetprism,5-facetprismand2glasseffectsrotatinginbothdirectionsatdifferentspeeds. -Prismoutsidediameter=��.�mm -Fineprismindexingandrotation -1�Prism/gobomacros
Strobe - Strobe effect with variable speed (1 - 15 flashes per second) -Preprogrammedmacroswithvariable/randompulseeffects
Dimmer -Smoothmicro-stepdrivendimming
Frost - Separate variable frost for fine frosting
Focus/Zoom -Remotelycontrollablemotorizedfocus -Motorizedzoomwithrange10°-�0°
Iris - Motorized (steplessly adjustable) iris for different beam diameters
Motors -17highqualitystepping-motorscontrolledbymicroprocessors
�7
Electronics -controlviacontrolpanelwithgraphicLCDdisplayand2buttons/rotatingwheel - Readout fixture and lamp usage,receiving DMX values, temperature, etc - Built-in analyzer for easy fault finding,error messages -Remotelyswitchingon/offthelampbyDMX -Bilt-indemosequences -Standaloneoperation -Self-resetablethermo-fuse -DigitalserialinputDMX-512 -Ethernetconnector -Magneticorelectronicsballast -�control-channelspresettings(2�and�2controlchannels) -SupportRDM
Data input/output -�-pinand5-pinXLRmalesocketsforDMXdatainput -�-pinand5-pinXLRfemalesocketsforDMXdataoutput -RJ-�5malesocketforEthernetconnection
Pan/Tilt -Panmovementrange5�0° -Tiltmovementrange2�0° -1�bitmovementresolution -AutomaticPan/Tiltpositioncorrection -RemotelycontrollablespeedofPan/Tiltmovementforeasyprogramming -MaximumPanmovement5�0°in�.5s -MaximumTiltmovement2�0°in�.�s
Rigging - Stands directly on the floor -Mountshorizontallyorverticallywith2clamps -fasteningoftheclampbracketsin�positions -Safetychain/cordattachmentapertures
Temperatures -Maximumambienttemperature:�5°C -Maximumhousingtemperatureofthehead:1�0°C
Beam path Lamp:MSRGOLD1200FastFit
Minimum distances - Min. distance from flammable surfaces: 1.2 m - Min. distance to lighted object: 5.0 m
Beam angle 10°- min. zoom
Beam angle 30° - max. zoom
��
Dimensions and weight
Weight:�2kg
Accessories: Gobo-set1�(No.1505002�).......................................................1piece MountingbracketOmegaCLassembled(No.��010�20)..........2pieces
Optional acesories: RemotecontrolIR(No.1�050�1�) FlashCableRS2�2/DMX(No.1�050�2�)
14. Maintenance and cleaningIt is absolutely essential that the fixture is kept clean and that dust, dirt and smoke-fluid residues must not build up on or within the fixture. Otherwise, the fixture‘s light-output will be significantly reduced. Regular cleaning will not only ensure the maximum light-output, but will also allow the fixture to function reliably throughout its life. A soft lint-free cloth moistened with any good glass cleaning fluid is recommended, under no circumstances should alcohol orsolventsbeused!
DANGER ! Disconnect from the mains before starting any maintenance work
The front objective lens will require weekly cleaning as smoke-fluid tends to building up residues, reducing the light-output veryquickly.Thecooling-fansshouldbecleanedmonthly.The interior of the fixture should be cleaned at least annually using a vacuum-cleaner or an air-jet.Dichroic colour filters, CMY lamelas,gobo wheels and the internal lenses should be cleaned monthly.Removedustanddirtfromthefansandcoolingventsusingasoftbrushandvacuum-cleaner.
Important! Check the air filters periodically and clean before they become clogged!
Clean the air filters with a vacuum cleaner or you can wash them and put back dry.Replacing the air filters in the fixture head. 1)Disconect the fixture from power. 2)Removebothtopandbottomcoverofthehead(bylooseningthe�quarter-turnfastenersoneachcover) 3)Remove the air filters (they are fixed with Velcro fastener) from grids. 4)Clean or replace the air filters. 5)Place the filters on the grid and put head cover back. �)ResettheelapsedtimecounterinmenuFixtureinformation(FixtureInformation--->AirFilters--->Elapsed Time.
��
Replacing the air filter in the fixture base. 1)Disconect the fixture from power. 2)Removesidefanscoverbylooseningthe�quarter-turnfasteners. 3)Remove the air filter from the cover. 4)Clean or replace the air filter. 5)Place the filter on the cover and put this cover back. �)ResettheelapsedtimecounterinmenuFixtureinformation(FixtureInformation--->AirFilters--->Elapsed Time.
Replacing the fuseIf the lamp burns out, the fine-wire fuse of the device might fuse, too. Only replace the fuse by a fuse of the same type andrating.Beforereplacingthefuse,unplugmainslead.
Procedure: 1) Unscrew the fuseholder on the rear panel of the base with a fitting screwdriver from the housing (anti-clockwise). 2)Removetheoldfusefromthefuseholder. �)Installthenewfuseinthefuseholder. 4) Replace the fuseholder in the housing and fix it.
Morecomplicatedmaintenanceandserviceoperationsareonlytobecarriedoutbyauthorizeddealers.
Specifications are subject to change without notice.
air filter cover
quarter-turn fasteners
grid
Velcrofastener
air filter
�0