competence in cable technology - webzdarma · 2 kerpen as an innovative, independent company in the...

Syn

opsis

53

CO

MP

ET

EN

CE

I

N

CA

BL

E

TE

CH

NO

LO

GY

Kerpen special GmbH & Co. KG · Zweifaller Straße 275-287 · D-52224 Stolberg

Phone: +49/24 02/17-1 · Fax: +49/24 02/7 51 54

E-Mail: [email protected] · http://www.kerpen.com

*************

MegaLine

Copper Data Cablesfor IT cabling

Important Definitions:

ACR*Attenuation Cross-talk Ratio – the difference between attenuationand cross-talk attenuation. The ACR is used as a measure for the ratioof signal power to disturbance power.

Attenuation*The ratio between the power received at the end of a pair and thepower fed in at the beginning. Attenuation is given as a power ratioin logarithmic form (dB).

Channel*Channel or the entire transmission circuit without the plug-in connec-tors on the terminal devices

Characteristic Wave Impedance*This is defined as the ratio between voltage and current. It is thecharacteristic value for a homogeneous cable and characterises thetransmission system. In conjunction with the return loss, the charac-teristic wave impedance describes the transmission circuit.

Cross-talk Attenuation*A measure for the ratio between the power launched unintentionallyinto pair x from pair y and that fed into pair y.

Delay*Delay in signal transmission of a pair and thus restriction of thetransmission rate. The signal delay causes frequency-dependent signaldistortion.

FEXT*Far End Cross-talk. A distinction is made between Input-Output FEXT(I/O FEXT) and Equal Level FEXT (EL-FEXT).

Input Impedance*A frequency-dependent value corresponding to the characteristic waveimpedance which takes the inhomogeneities of the cable intoaccount. A transmission circuit can be described via this value.

NEXT*Near End Cross-talk.

Permanent LinkThe cable link installed between the patch panel and the socket (TA)

Power Sum (PS)*The power sum describes the sum total of all disturbance power laun-ched into a pair due to cross-talk. Power sum measurement comesvery close to application for Gigabit Ethernet, in which all pairs are inoperation. The Power Sum can be formed for ACR NEXT and FEXT.

Return Loss (RL)*This value describes the inhomogeneities in terms of the ratio bet-ween the forward electromagnetic wave and the return wave.

Skew*The difference between the delay times of two or more pairs. Theskew (delay) must be as small as possible for special applications, forexample Gigabit Ethernet.

DW 2

040-

2 M

egaL

ine-

Bros

chür

e GB

03/

01

2

Ker

pen As an innovative, independent company in the cable industry, we develop, produce and

market cables according to German and international standards, factory specifications and

the wishes of the customer.

In the field of cables and systems for information technology, we are one of the market

leaders in Europe with the MegaLineTM product family. Besides copper data cables of

the MegaLineTM brand, our product portfolio in the IT field also includes the copper system

technology ELineTM. Since January 2000, we have been producing GigaLineTM optical fibre

cables to the highest possible standards at our factory in Stolberg. The FLineTM cabling

system for optical fibres rounds off the IT product portfolio. Data cables and systems from

Kerpen are used mainly for Local Area Networks in structured in-door cabling and in

Metropolitan Area Networks for the operating of city networks. For cables for measurement

and control technology and for plant engineering, Kerpen has an important position inter-

nationally. It manufactures and markets high-quality power cables, telecommunications

cables and special cables for mining, industry and energy providers.

All our activities aim at quality and customer satisfaction – these are the standards by

which we are judged. Committed and creative employees contribute their abilities to the

realisation of this goal. The quality management system certified according to DIN ISO

9001 in 1990 and the environmental management system certified according to DIN EN ISO

14001 in 1998 also exclusively meet the demands of our customers for economy, reliability

and flexibility. – We will continue to work in this direction in the future.

Who are we ... Conductor diameter AWG/metric

Mechanical characteristics:

Synopsis of products

Product:

Horizontal cable

Backbone cable

Distribution centre for storey

Primary cable

Distribution centre for building

Conductor diameter (AWG) Structure Wire Ø Conductor Ø

Number of wires Nominal value Nominal value

Conductor diameter 27/7 7 0.14 0.43





51

MegaLine 8

MegaLine 7

MegaLine 6

MegaLine 5

Dimensions External Ø Weight Calorific value Product no. Bandwidthmm kg/km Mj/m MHz

4x2xAWG 22/1 8.5 90 0.74 7KS01138 1200 Page 10

4x2xAWG 23/1 7.5 70 0.65 7KS00916 800 Page 142x(4x2xAWG 23/1) 7.5x15.2 136 1.40 7KS01100 800 Page 164x2xAWG 26/7 6.2 46 0.42 7KS01067 900 Page 184x2xAWG 27/7 5.8 34 0.35 7KS01189 600 0

4x2xAWG 23/1 6.26 44 0.65 7KSO1375 300 Page 244x2xAWG 23/1 7.5 68 0.60 7KSOO533 450 Page 262x(4x2xAWG 23/1) 7.5x15.2 136 1.40 7KS00758 450 Page 284x2xAWG 23/1 7.2 57 0.75 7KS01167 450 Page 302x(4x2xAWG 23/1) 7.2x14.8 114 1.70 7KSO1336 7KSO1372* 450 Page 324x2xAWG 27/7 5.8 34 0.35 7KS01078 450 Page 34

4x2xAWG 24/1 6.0 44 0.38 0.40* 7KS00643 7KS00353* 200 Page 382x(4x2xAWG 24/1) 6.0x12.5 86 0.80 0.85* 7KS00763 7KS00729* 200 Page 404x2xAWG 26/7 5.7 35 0.29 0.31* 7KS00773 7KS00248* 250 Page 424x2xAWG 24/1 5.9 37 0.45 0.45* 7KS00649 7KS00354* 100 Page 444x2xAWG 26/7 5.0 26 0.35 7KS00601 100 Page 46

* for PVC version Other dimensions on request

Mega Line 5

MegaLine 524 SCMegaLine 524 SC DXMegaLine 526 SC flexMegaLine 524 SMegaLine 526 S flex

MegaLine 6

MegaLine 6UEMegaLine 623MegaLine 623 DXMegaLine 623 DSMegaLine 623 DS DXMegaLine 627 flex

MegaLine 7

MegaLine 723MegaLine 723 DXMegaLine 726 flexMegaLine 727 flex

MegaLine 8

3

Contents

Standardisation

Classes and Categories Page 4

Products

MegaLine – a reliable quantity Page 8

MegaLine 8 Page 9

MegaLine 7 Page 13

MegaLine 6 Page 23

MegaLine 5 7

Getting in Touch

Your Contacts at Kerpen special Page 48

In a Nutshell

Product Survey Page 50

Conductor Diameter Page 51

Important Definitions Page 53

MegaLine 8

MegaLine 7

MegaLine 6

MegaLine 5

Meg

aLine

With bandwidths of up to 450 MHz,

MegaLine 623 and 627 flex go far

beyond the performance of 250 MHz

required by the standard.

Trendsetting Performance

High bandwidths of up to 900 MHz,

an excellent NEXT and attenuation

response and an optimum cha-

racteristic wave impedance are a

few of the excellent features of

MegaLine 7 cables.

Of course, these are S/STP

cables with individual or overall

screening.

4

Cla

sses

The bodies responsible for standardisation are now taking the increasing requirements

with regard to the performance and flexibility of indoor cabling into account. Thus,

new additional features such as PS-NEXT, PS-ACR, FEXT, PS-FEXT and Skew are

being defined for the second edition of ISO/IEC 11801 and EN 50173. This will

be an essential step towards realising the high-speed ATM protocols with

155/622 Mbit/s and Gigabit Ethernet with 1000 Mbit/s.

Classes and categories

Good performance in

all categories

The performance of MegaLine

copper data cables offers the

user excellent reserve capacity

in all categories. With MegaLine

5, Category 5 cables with band-

widths of up to 250 MHz are

now available in a compact

design.

Screened performance

in Category 6

The new Category 6/Class E

allows the use of 4-pair S/UTP

cables with overall screening or

preferably of S/STP cables.

5

With a bandwidth which only

optical fibres seemed able to

achieve up to now, MegaLine 8 is

ideally suitable for multimedia

applications.

Multimedia

With MegaLine 8, Kerpen pre-

sents a copper data cable

which exceeds the require-

ments of the standards:

MegaLine 8 – the NEXT gene-

ration with a performance of

1200 MHz. In a class of its

own!

ISO/IEC 11801 EN50173 2nd edition

ELine 100 RJ ELine 250/600 RJ ELine 250/600 RJ ELine 600

Class D (e)Category 5 (e)

100 MHz

Class FCategory 7600 MHz

MegaLine 524 SCMegaLine 526 SC

-flex

MegaLine 622MegaLine 623MegaLine 727

-flex


-flex


-flex

Class ECategory 6250 MHz Standard

Connection technology

Cables

6

Cla

sses The parts that make up a whole

RJ45 plugs and sockets based on

EN 60603-7 are available for

basic applications.

ELine 600 EC7 – the multimedia

cabling system.

ELine 600 EC7 is a trailblazing

cabling system for multimedia

applications. It forms the per-

fect symbiosis of copper data

cables and connection technolo-

gy by continuing the pimf

screening in the EC7 plug.

Conclusion: you’ve made a good

connection!

A cabling system is only as strong as its weakest link. This is why the performance

parameters and the quality of the cables are the primary values in the chain

of system components. If connection technology and cables have been ideally

matched, the overall cabling circuit provides maximum benefit, maximum

reserve capacity and maximum safety.

Trailblazer

With ELine RJ, Kerpen special offers

cabling systems with a modular

structure. All components are com-

patible, allow economical retro-

fitting from Class D to Class F.

80

70

60

50

40

30

20

10

01 10 100 600 1000

MHz

dB

60

50

40

30

20

10

0

0,1 1 10 100 600 1000

MHz

dB

A

B

C

D E

F

ACR curve for transmission channel of classes A to F

Class A

Class B

Class C

Class D

Class E

Class F

Attenuation and NEXT curve for cables of categories 3 to 7

Category 3

Category 4

Category 5

Category 6

Category 7

the channel and the permanent link for

classes D, E and F are being defined at

present.

The requirements for cables of Cate-

gories 5 to 7 according to EN 50288

are currently being passed.

7

ClassesThe cable link

Specifying the transmission charac-

teristics for new categories and

classes also means defining the

l inks according to pract ical

requirements. The requirements for

Up to now

Link according to ISO/IEC 11801 and EN 50173

PC Patch panel Unit

5m - xmFlexible connection cable

90mStorey cable

5m + xmFlexible connection cable

New

Channel according to ISO/IEC 11801 2nd edition

PC Socket Patch panel Unit


90mStorey cable


Cross-connect

Permanent linksAcc. to ISO/IEC 11801 2nd edition

Socket

Standard MegaLine cables offer

optimum protection against fire

and are environmentally sound as

they use halogen-free, flame-

retardant materials only.

Thanks to innovative insulation

methods such as foaming,

MegaLine cables combine maxi-

mum performance with low space

requirements. Their small outer

diameter, defined curvature radius

and low weight make them easy

to install.

• Flame-retardant according to

IEC 60332-3

• Reduced calorific values

• Smoke density according to

IEC 61034

• Low toxicity

• No dioxines

• Corrosivity according to IEC 60754-2

The MegaLine cables of all categories

and classes feature a convincing

transmission capacity and high

safety reserves.

With their double screening and the

pimf screening in the case of S/STP

cables, they offer an especially

high degree of electromagnetic

compatibility.

The demands made on cabling are varied and at times contradictory. MegaLine data

and communication cables made of copper combine high performance, universality

and economy. This standard of quality can only be achieved by means of an

integrated cable design.

8

Meg

aLin

eA reliable quantity

Halogen-free and flame-retardant covering

1 overall screen made of Cu braiding

1 foil screen around each pair= pimf (pair in metal foil)

2 wires twisted to form a pair

As a state-of-the-art data cable,

MegaLine 8 offers universality

and a performance which only

optical fibres were able to

achieve up to now.

9

MegaLine 8

ATM, Gigabit Ethernet – the demands

which data transmission makes on

speed and bandwidth are increasing

rapidly. MegaLine 8 embodies the

highest level of evolution available

up to now in an S/STP data cable.

MegaLine 8 – the NEXT generation

Meg

aLine

8

10

Meg

aLin

e8

MegaLine 8

Communication cable 1200 MHz

S/STP 100 ohm – LSFROHTertiary area

Type: KS-02YSCH nx2xAWG 22/1 pimf-100 ohm

Structure

Conductor

Bare Cu wire,AWG 22/1

Insulation

Cellular PE,Core ø: max. 1.6 mm

Pair cabling2 cores form a pair

Colour codewt/bl, wt/or, wt/gn, wt/br

Individual screen

Aluminium bonded polyester tape,metal side outwards

Cabling4 pairs twisted together

Outer sheath

Halogen-free compound

ColourLight ivory – RAL 1015

Overall screen

Tinned copper wire braid

Marking

• KERPEN special MegaLine 8 “Number of pairs” *H*,

Meter marking

Range of application

• Primary, secondary, tertiary

• Category 5 acc. to EN 50173, EN 50173 “2nd edition”,

ISO/IEC 11801, ISO/IEC 11801 “2nd edition”,

EN 50167, EN 50169

• Category 6 and Category 7 acc. to ISO/IEC 11801

”2nd edition”, EN 50173 ”2nd edition” and

prEN 50288-4-1, August 2000

• IEEE 802.3 10 BASE T Ethernet

• IEEE 802.3u 100 BASE T Fast Ethernet

• IEEE 802.3ab 1000 BASE T Gigabit Ethernet

• IEEE 802.5 Token Ring

• IEEE 802.12 100VG-AnyLAN

• FDDI on copper, ISDN, B-ISDN, ATM, DQDB, Video

Temperature range

• For the static state: -20˚C bis +60˚C

• For the moving state: 0˚C bis +50˚C

Bending radius

• At least 8 x external diameter during laying

• At least 4 x external diameter after installation

Flame retardance

• Acc. to IEC 60332-3 Cat.C

Absence of halogens

• Acc. to IEC 60754-2

Smoke density

• Acc. to IEC 61034

We assume no liability for printing errors, mistakes and technical changes.

Dimensions External ø Weight Calorific value Product No.

mm kg/km MJ/m kWh/m(recommended value) (recommended value) (recommended value) (recommended value)

4x2xAWG 22/1 8.5 90 0.74 0.21 7KS01138

11

Electrical characteristics at 20˚C

MegaLine 8

DC resistance (ohm/km) 57.1 (max.)

Insulation resistance (G ohm/km) 5 (min.)

Mutual capacitance (pF/m) 40 (nominal value)

Transfer capacitance (e) (pF/km) 1500 (max.)

Signal velocity (c) 0.8 (recommended value)

Propagation delay (ns/100m) 420 (recommended value)

Skew at 100 MHz (ns/100m) 4 (recommended value)

Transfer impedance at 10 MHz (mohm/m) 5 (nominal value)·acc. to IEC 96-1; A5.2

Screening attenuation up to 1000 MHz (dB) 80 (nom.)

Coupling attenuation up to 1000 MHz (dB) 90 (nom.)

Impedance from 1 to 100 MHz (ohm) 100 ± 15 %



Test voltage Ueff (V) 1000 (core/core)

500 (core/screen)

Operating voltage (V) 125 (max.)

MHz1 10 100 1000 1200

dB

0

1 0

2 0

3 0

4 0

5 0

6 0

70

80

90

Next Nominal value

Next Category 7

Next Category 5

Attenuation Category 5


Attenuation Nominal value

Frequency (MHz) 1.0 4.0 10.0 16.0 20.0 31.25 62.5 100.0 155.0 200.0 300.0 600.0 1000.0 1200.0

Attenuation (dB/100m) Nominal value 1.6 2.6 4.5 6.0 6.8 8.6 12.1 15.4 19.2 21.7 27.0 38.0 49.0 56.0

Category 7* (max.) 2.0 3.6 5.7 7.2 8.1 10.1 14.5 18.5 23.4 26.8 33.4 49.0 n.def. n.def.

NEXT (dB) Nominal value 90.0 90.0 90.0 90.0 90.0 90.0 90.0 90.0 90.0 89.0 88.0 80.0 70.0 60.0

Category 7* (min.) 80.0 80.0 80.0 80.0 80.0 79.6 75.1 72.4 69.6 67.9 65.3 60.8 n.def. n.def.

ACR (dB/100m) Nominal value 88.4 87.4 85.5 84.0 83.2 81.4 77.9 74.6 70.8 67.3 61.0 42.0 21.0 4.0


PS-NEXT (dB) Nominal value 87.0 87.0 87.0 87.0 87.0 87.0 87.0 87.0 87.0 86.0 85.0 77.0 67.0 57.0


PS-ACR (dB/100m) Nominal value 85.4 84.4 82.5 81.0 80.2 78.4 74.9 71.6 67.8 64.3 58.0 39.0 18.0 1.0


EL-FEXT (dB/100m) Nominal value 90.0 90.0 90.0 90.0 90.0 90.0 90.0 85.0 80.0 75.0 70.0 60.0 40.0 35.0


PS-EL-FEXT (dB/100m) Nominal value 87.0 87.0 87.0 87.0 87.0 87.0 87.0 82.0 77.0 72.0 67.0 57.0 37.0 32.0


RL (dB) Nominal value 27.0 30.0 30.0 30.0 28.0 25.0 24.0 24.0 24.0 24.0 21.0

Category 7* (min.) 23.0 23.0 23.0 23.0 23.0 23.0 23.0 21.5 21.5 20.7 17.7 n.def. n.def.

* Category 7 according to prEN 50288-4-1, August 2000


specialadvanced communication cables & systems

12

Note

s

13

MegaLine 7 is thus synonymous

with excellent protection of

your investment and a secure

future. Single and duplex ver-

sions allow the user to choose

from a product program which

meets all practical requirements.

MegaLine 7

MegaLine 7 S/STP cables go far

beyond the requirements of Cate-

gory 7/Class F.

Here “trendsetting” means that

present and future applications

can be transmitted via a reserve

capacity of up to 900 MHz.

Meg

aLine

7

MegaLine 7 – the trendsetters



2x2xAWG 23/1 4.5x7.5 50 0.5 0.14 7KS009184x2xAWG 23/1 7.5 70 0.65 0.19 7KS00916

14

Meg

aLin

e7

MegaLine 723

Communication cable 800 MHzBetter than the new Category 7



Structure

Conductor


Insulation

Cellular PE,Core ø: Nominal value 1.4mm



Individual screen


Cablingn pairs twisted together (at n>2)

Outer sheath


ColourYellow – RAL 1021

Overall screen


Marking


Meter marking





EN 50167, EN 50169


“2nd edition”, EN 50173 “2nd edition” and

prEN 50288-4-1, August 2000







Temperature range



Bending radius



Flame retardance


Absence of halogens

• Acc. to IEC 60754-2

Smoke density



15


MegaLine 723

DC resistance (ohm/km) 75 (max.)














500 (core/screen)



MHz1 10 100 1000

dB

0

1 0

2 0

3 0

4 0

5 0

6 0

70

80

90

Frequency (MHz) 1.0 4.0 10.0 16.0 20.0 31.25 62.5 100.0 155.0 200.0 300.0 600.0 800.0

Attenuation (dB/100m) Nominal value 1.8 2.9 5.3 7.0 7.7 9.9 13.9 17.8 22.0 25.4 31.6 47.0 57.2

Category 7* (max.) 2.0 3.6 5.7 7.2 8.1 10.1 14.5 18.5 23.4 26.8 33.4 49.0 n.def.

NEXT (dB) Nominal value 90.0 90.0 90.0 90.0 90.0 90.0 90.0 89.0 84.0 82.0 78.0 73.0 71.0

Category 7* (min.) 80.0 80.0 80.0 80.0 80.0 79.6 75.1 72.4 69.6 67.9 65.3 60.8 n.def.

ACR (dB/100m) Nominal value 88.2 87.1 84.7 83.0 82.3 80.1 76.1 71.2 62.0 56.6 46.4 26.0 13.8


PS-NEXT (dB) Nominal value 87.0 87.0 87.0 87.0 87.0 87.0 87.0 86.0 81.0 79.0 75.0 70.0 68.0


PS-ACR (dB/100m) Nominal value 85.2 84.1 81.7 80.0 79.3 77.1 73.1 68.2 59.0 53.6 43.4 23.0 10.8


EL-FEXT (dB/100m) Nominal value 90.0 90.0 90.0 90.0 90.0 90.0 85.0 80.0 77.0 75.0 66.0 60.0 45.0


PS-EL-FEXT (dB/100m) Nominal value 87.0 87.0 87.0 87.0 87.0 87.0 82.0 77.0 74.0 72.0 63.0 57.0 42.0



Category 7* (min.) 23.0 23.0 23.0 23.0 23.0 23.0 23.0 21.5 21.5 20.7 17.7 n.def.

Next Nominal value

Next Category 7

Next Category 5






16

Meg

aLin

e7

Structure

Conductor


Insulation

Cellular PE, Core ø:Nominal value 1.4 mm



Individual screen



Outer sheath

Halogen-free compound, figure 8 with seperator,2 parallel basic elements

ColourYellow – RAL 1021

Overall screen


Marking

• KERPEN special MegaLine 723

2x4 P *H*, Meter marking





EN 50167, EN 50169



prEN 50288-4-1, August 2000







Temperature range



Bending radius



Flame retardance


Absence of halogens

• Acc. to IEC 60754-2

Smoke density


MegaLine 723 Duplex



Type: KS-02YSCH 2x(4x2xAWG 23/1 pimf)-100 ohm




2x(4x2xAWG 23/1) 7.5x15.2 136 1.4 0.38 7KS01100

17


MegaLine 723 Duplex















500 (core/screen)


1 10 100 1000MHz

dB

0

1 0

2 0

3 0

4 0

5 0

6 0

70

80

90

Next Nominal value

Next Category 7

Next Category 5




Frequency (MHz) 1.0 4.0 10.0 16.0 20.0 31.25 62.5 100.0 155.0 200.0 300.0 600.0 800.0




















18

Meg

aLin

e7

MegaLine 726 flex




Structure

Conductor

Bare Cu strand,AWG 26/7

Insulation

Cellular PE,Core ø: Nominal value 1.0 mm



Individual screen


Cablingn pairs twisted together (at n>2)

Outer sheath


ColourGrey – RAL 7035

Overall screen


Marking

• KERPEN special MegaLine 726 flex

“Number of pairs” *H*


• Work area, device connection, patch panel



EN 50168



prEN 50288-4-2, August 2000







Temperature range



Bending radius

• At least 5 x external diameter

Flame retardance


Absence of halogens

• Acc. to IEC 60754-2

Smoke density





2x2xAWG 26/7 3.8x5.3 27 0.35 0.10 7KS010684x2xAWG 26/7 6.2 46 0.42 0.13 7KS01067

19


MegaLine 726 flex














500 (core/screen)



MHz1 10 100 1000

dB

0

1 0

2 0

3 0

4 0

5 0

6 0

70

80

90

Frequency (MHz) 1.0 4.0 10.0 16.0 20.0 31.25 62.5 100.0 155.0 200.0 300.0 600.0 900.0

















Next Nominal value

Next Category 7

Next Category 5






20

Meg

aLin

e7

MegaLine 727 flex


S/STP 100 ohm – LSFROHWork area


Structure

Conductor


Insulation




Individual screen



Outer sheath



Overall screen


Marking

• KERPEN special MegaLine 727 flex 4P *H*




ISO/IEC 11801, ISO/IEC 11801 ”2nd edition”,

EN 50168

• Category 6 acc. to ISO/IEC 11801 “2nd edition”,

EN 50173 “2nd edition” and prEN 50288-5-2,

August 2000







Temperature range



Bending radius


Flame retardance


Absence of halogens

• Acc. to IEC 60754-2

Smoke density





4x2xAWG 27/7 5.8 34 0.35 0.1 7KS01189

21* Category 6 according to prEN 50288-5-2, August 2000

1 10 100 1000

dB

0

1 0

2 0

3 0

4 0

5 0

6 0

70

80

90

• Next Nominal value

• Next Category 6

• Next Category 5





MegaLine 727 flex













500 (core/screen)


Frequency (MHz) 1.0 4.0 10.0 16.0 20.0 31.25 62.5 100.0 155.0 200.0 250.0 300.0 450.0 600.0

Attenuation (dB/10m) Nominal value 0.30 0.60 0.90 1.10 1.30 1.60 2.30 2.90 3.60 4.20 4.70 5.20 6.40 7.80

Category 6* (max.) 0.31 0.58 0.90 1.14 1.28 1.61 2.32 2.99 3.80 4.37 4.95 n.def. n.def. n.def.

NEXT (dB) Nominal value 90.0 90.0 90.0 87.0 85.0 82.0 77.0 74.0 71.0 69.0 68.0 66.0 64.0 63.0

Category 6* (min.) 66.0 65.3 59.3 56.2 54.8 51.9 47.4 44.3 41.4 39.8 38.3 n.def. n.def. n.def.

ACR (dB/10m) Nominal value 89.7 89.4 89.1 85.9 83.7 80.4 74.7 71.1 67.4 64.8 63.3 60.8 57.6 55.2


PS-NEXT (dB) Nominal value 87.0 87.0 87.0 84.0 82.0 79.0 74.0 71.0 68.0 66.0 65.0 63.0 61.0 60.0


PS-ACR (dB/100m) Nominal value 86.7 86.4 86.1 82.9 80.7 77.4 71.7 68.1 64.4 61.8 60.3 57.8 54.6 52.2


EL-FEXT(dB/100m) Nominal value 90.0 90.0 90.0 85.0 80.0 70.0 60.0 50.0 45.0 40.0 35.0 30.0 25.0 20.0

Category 6* (min.) 58.0 50.0 45.9 44.0 40.1 34.1 30.0 26.2 24.0 22.0 n.def. n.def. n.def.

PS-EL-FEXT (dB/100m) Nominal value 87.0 87.0 87.0 82.0 77.0 67.0 57.0 47.0 42.0 37.0 32.0 27.0 22.0 17.0






22

Note

s

23

With MegaLine 623 and

MegaLine 623 DS, there are

now cables of Category 6 Class E

which, with their bandwidth

of 450 MHz, have exceptional

reserve capacities.

MegaLine 6

MegaLine 6 was and is a develop-

ment with a vision. As early as 1991,

the first MegaLine 6 was presented

as an S/STP cable in 100 Ω technolo-

gy. This cable paved the way for the

success of all S/STP cables.

Meg

aLine

6

MegaLine 6 – the classic with a future

24

Meg

aLin

e6

MegaLine 6Ue


UTP 100 ohm – halogen-freeHorizontal area

Type: KS-2YH 4x2xAWG 23/1-100 ohm

Structure

Conductor

bare Cu wire,AWG 23/1

Insulation

PE


Colour codewtbl/bl, wtor/or, wtgn/gn, wtbr/br

Cabling

4 pairs twisted together and central cross element

Outer sheath


ColourOrange – RAL 2003

Wrapping

1 layer plastic-foil

Marking

• KERPEN special MegaLine 6U Enhanced *H*,

Meter marking


• Backbone and horizontal applications



EN 50167, EN 50169


and prEN 50288-5-1, August 2000







Temperature range



Bending radius



Flame retardance

• Acc. to IEC 60332-1

Absence of halogens

• Acc. to IEC 60754-2

Smoke density



mm kg/km MJ/m kWh/m Halogen-free(recommended value) (recommended value) (recommended value) (recommended value) outer sheath

4x2xAWG 23/1 6.26 44 0.65 0.19 7KS01375




• Next Category 6




Frequency (MHz) 1.0 4.0 10.0 16.0 20.0 31.25 62.5 100.0 155.0 200.0 250.0 300.0

Attenuation (dB/100m) Nominal value 1.8 3.6 5.8 7.4 8.3 10.6 15.2 19.6 25.1 29.0 33.0 33.1

Category 6* (max.) 2.1 3.8 6.0 7.6 8.5 10.7 15.5 19.9 25.3 29.2 33.0 n.def.

NEXT (dB) Nominal value 90.0 77.0 65.0 64.0 61.0 59.0 57.0 55.0 53.0 51.0 50.0 48.0


ACR (dB/100m) Nominal value 88.2 73.4 59.2 56.6 52.7 48.4 41.8 35.4 27.9 22.0 17.0 14.9


PS-NEXT (dB) Nominal value 87.0 83.0 62.0 61.0 58.0 56.0 55.0 54.0 53.0 50.0 48.0 47.0


PS-ACR (dB/100m) Nominal value 85.2 79.4 56.2 53.6 49.7 45.4 39.8 34.4 27.9 21.0 15.0 13.9


EL-FEXT (dB/100m) Nominal value 69.0 62.0 52.0 49.0 46.0 43.0 40.0 32.0 30.0 28.0 27.0 25.0


RS-EL-FEXT (dB/100m) Nominal value 68.0 61.0 51.0 48.0 45.0 42.0 39.0 31.0 29.0 27.0 23.0 21.0


RL (dB) Nominal value 30.0 24.0 25.0 25.0 24.0 23.0 23.0 23.0 23.0 22.0 21.0 21.0

Category 6* (min.) 23.0 23.0 23.0 23.0 23.0 23.0 21.1 20.0 19.0 n.def.




MegaLine 6Ue











1 10 100 1000MHz

dB

0

1 0

2 0

3 0

4 0

5 0

6 0

70

80

90

26

Meg

aLin

e6

MegaLine 623




Structure

Conductor


Insulation




Individual screen


Cablingn pairs twisted together (bei n>2)

Outer sheath


ColourLight orange – RAL 2003

Overall screen


Marking


Meter marking





EN 50167, EN 50169









Temperature range



Bending radius



Flame retardance


Absence of halogens

• Acc. to IEC 60754-2

Smoke density




2x2xAWG 23/1 4.5 x7.5 50 0.5 0.14 7KS005344x2xAWG 23/1 7.5 68 0.6 0.17 7KS00533



MHz1 10 100 1000

dB

0

1 0

2 0

3 0

4 0

5 0

6 0

70

80

90






500 (core/screen)


MegaLine 623










Frequency (MHz) 1.0 4.0 10.0 16.0 20.0 31.25 62.5 100.0 155.0 200.0 250.0 300.0 450.0


Category 6* (max.) 2.1 3.8 6.0 7.6 8.5 10.8 15.5 19.9 25.3 29.1 33.0 n.def. n.def.











RS-EL-FEXT (dB/100m) Nominal value 87.0 87.0 87.0 87.0 87.0 84.0 81.0 70.0 73.0 65.0 63.0 60.0 52.0



Category 6* (min.) 23.0 23.0 23.0 23.0 23.0 23.0 23.0 21.0 20.0 19.0 n.def. n.def.




• Next Category 6

• Next Category 5




28

Meg

aLin

e6

Structure

Conductor


Insulation

Cellular PE, Core ø: Nominal value 1.4 mm



Individual screen



Outer sheath

Halogen-free compound, figure 8 with seperator, 2 parallel basic elements


Overall screen


Marking

• KERPEN special MegaLine 623 2x4 P *H*,

Meter marking





EN50167, EN 50169









Temperature range



Bending radius



Flame retardance


Absence of halogens

• Acc. to IEC 60754-2

Smoke density


MegaLine 623 Duplex



Type: KS-02YSCH 2x(4x2xAWG 23/1 pimf)-100 ohm



2x(4x2xAWG 23/1) 7.5x15.2 136 1.4 0.38 7KS00758








500 (core/screen)


MegaLine 623 Duplex










Frequency (MHz) 1.0 4.0 10.0 16.0 20.0 31.25 62.5 100.0 155.0 200.0 250.0 300.0 450.0

Attenuation (dB/100m Nominal value 1.9 3.6 5.7 7.4 8.2 10.4 15.0 19.2 25.2 29.0 32.5 35.0 42.0


















MHz1 10 100 1000

dB

0

1 0

2 0

3 0

4 0

5 0

6 0

70

80

90


• Next Category 6

• Next Category 5




30

Meg

aLin

e6

Structure

Conductor


Insulation

Cellular PE



Individual screen

Aluminium bonded polyester tape, metal side outwards


Outer sheath

Halogen-free compound,


Overall screen

Aluminium bonded polyester tape, metal side inwards, with underlayed tinnedcopper drain wire at AWG 24/1

Marking

• KERPEN special MegaLine 623 DS, 4P *H*,

for halogen-free version





EN 50167, EN 50169

• Category 6 acc. to ISO/IEC 11801 “2nd edition”



• EEE 802.3u 100 BASE T Fast Ethernet





Temperature range



Bending radius



Flame retardance


Absence of halogens

• Acc. to IEC 754-2

Smoke density


MegaLine 623 DS


F/FTP 100 ohm – LSFROHHorizontal area

Type: KS-02YS (St) H 4x2xAWG 23/1 pimf-100 ohm



4x2xAWG 23/1 7.2 57 0.75 0.20 7KS01167



MHz1 10 100 1000

dB

0

1 0

2 0

3 0

4 0

5 0

6 0

70

80

90


Transfer impedance at 10 MHz (mohm/m) 100 (max.)·acc. to IEC 96-1; A5.2

60 (typ.)


500 (core/screen)


MegaLine 623 DS








Frequency (MHz) 1.0 4.0 10.0 16.0 20.0 31.25 62.5 100.0 155.0 200.0 250.0 300.0 450.0
















Category 6* (min.) 23.0 23.0 23.0 23.0 23.0 23.0 21.1 20.0 19.0 n.def. n.def.




• Next Category 6

• Next Category 5




32

Meg

aLin

e6

Structure

Conductor


Insulation

Cellular PE



Individual screen

Aluminium bonded polyester tape, metal side outwards


Outer sheath

Halogen-free compound or PVC, figure 8 with seperator, 2 parallel basic elements


Overall screen

Aluminium bonded polyester tape, metal side inwards, with underlayedtinned copper drain wire at AWG 24/1

Marking

• KERPEN special MegaLine 623 DS 2x4 P *H*,

for halogen-free version, additional marking:

*H*, meter marking



• Category 5 and Category 5e acc. to EN 50173,

EN 50173 “2nd edition”, ISO/IEC 11801,

ISO/IEC 11801 “2nd edition”, EN 50167, EN 50169

• Category 6 acc. to ISO/IEC 11801 “2nd edition”








Temperature range



Bending radius



Flame retardance

• Acc. to IEC 60332-1 (PVC)


Absence of halogens

• Acc. to IEC 754-2

Smoke density


MegaLine 623 DS Duplex


F/FTP 100 ohm (S/STP) Duplex – LSFROHHorizontal area

Type: KS-02YS(St)H 2x(4x2xAWG 23/1 pimf)-100 ohmKS-02YS(St)Y 2x(4x2xAWG 23/1 pimf)-100 ohm



mm kg/km MJ/m kWh/m LSFROH PVC(recommended value) (recommended value) (recommended value) (recommended value) outer sheath

2x (4x2xAWG 23/1) 7.2x14.8 114 1.70 0.44 7KS01336 7KS01372


MHz1 10 100 1000

dB

0

1 0

2 0

3 0

4 0

5 0

6 0

70

80

90


Frequency (MHz) 1.0 4.0 10.0 16.0 20.0 31.25 62.5 100.0 155.0 200.0 250.0 300.0 450.0
















Category 6* (min.) 23.0 23.0 23.0 23.0 23.0 23.0 21.1 20.0 19.0 n.def. n.def.



60 (typ.)


500 (core/screen)


MegaLine 623 DS Duplex







Skew at 100 (ns/100m) 12 (recommended value)




• Next Category 6

• Next Category 5




34

Meg

aLin

e6

MegaLine 627 flex


S/STP 100 ohm – LSFROHWork area


Structure

Conductor


Insulation




Individual screen



Outer sheath



Overall screen


Marking

• KERPEN special MegaLine 627 flex 4P *H*



• Category 5 acc. to EN 50173, EN 50173 ”2nd edition”,


EN50168









Temperature range



Bending radius


Flame retardance


Absence of halogens

• Acc. to IEC 60754-2

Smoke density




4x2xAWG 27/7 5.8 34 0.35 0.1 7KS01078


35


Frequency (MHz) 1.0 4.0 10.0 16.0 20.0 31.25 62.5 100.0 155.0 200.0 250.0 300.0 450.0

















MHz1 10 100 1000

dB

0

1 0

2 0

3 0

4 0

5 0

6 0

70

80

90


MegaLine 627 flex


Insulation resistance (G ohm x km) 5 (min.)











500 (core/screen)





• Next Category 6

• Next Category 5




36

Note

s

37

Their compact design gives

them advantages with regard to

dimensions, weight, calorific

value and handling.

MegaLine 5 cables are available

in single or multiplex versions.

MegaLine 5

The tried and tested MegaLine 5

cables were optimised for the cha-

racteristics of the new Category 5e.

Meg

aLine

5

MegaLine 5 – the compact cables

38

Meg

aLin

e5

MegaLine 524 SC

Communication cable 200 MHzBetter than Category 5e

S/UTP 100 ohmTertiary area

Type: KS-02YS(St+C)H nx2xAWG 24/1-100 ohmKS-02YS(St+C)Y nx2xAWG 24/1-100 ohm

Structure

Conductor


Insulation





WrappingPlastic film

Outer sheath

Halogen-free compound or PVC

ColourLight grey – RAL 7000

Overall screen

Aluminium bonded polyester tape and Tinned copper wire braid

Marking

• KERPEN special MegaLine 524 SC “Number of pairs”,


*H*, meter marking





EN 50167, EN 50169 and prEN 50288-2-1,

August 2000







Temperature range



Bending radius



Flame retardance

• Acc. to IEC 60332-1

• Halogen-free version:

Acc. to IEC 60332-3 Cat.C

Halogen-free version

• Absence of halogens acc. to IEC 60754-2

• Smoke density acc. to IEC 61034


mm kg/km MJ/m kWh/m Halogen-free PVC(recommended value) (recommended value) (recommended value) (recommended value) outer sheath outer sheath

4x2xAWG 24/1 6.0 44 0.40 0.12 7KS003534x2xAWG 24/1 6.0 44 0.38 0.11 7KS00643


39


Frequency (MHz) 1.0 4.0 10.0 16.0 20.0 31.25 62.5 100.0 200.0

Attenuation (dB/100m) Nominal value 2.1 3.9 5.9 7.4 8.2 10.3 14.7 18.8 27.0

Category 5* (max.) 2.1 4.0 6.3 8.0 9.0 11.4 16.5 21.3 n.def.

NEXT (dB) Nominal value 70.0 62.0 56.0 53.0 51.0 49.0 44.0 41.0 33.0

Category 5* (min.) 65.3 56.3 50.3 47.3 45.8 42.9 38.4 35.3 n.def.

ACR (dB/100m) Nominal value 67.9 58.1 50.1 45.6 42.8 38.7 29.3 22.2 6.0


PS-NEXT (dB) Nominal value 67.0 59.0 53.0 50.0 48.0 46.0 41.0 38.0 31.0


PS-ACR (dB/100m) Nominal value 64.9 55.1 47.1 42.6 39.8 35.7 26.3 19.2 4.0


EL-FEXT (dB/100m) Nominal value 71.0 70.0 61.0 57.0 55.0 50.0 46.0 41.0 31.0


RS-EL-FEXT (dB/100m) Nominal value 68.0 67.0 58.0 54.0 52.0 47.0 43.0 38.0 28.0


RL (dB) Nominal value 26.0 26.0 25.0 25.0 24.0 24.0 24.0 20.0

Category 5* (min.) 23.0 23.0 23.0 23.0 23.0 23.0 23.0 n.def.

1 10 100 1000MHz

dB

0

1 0

2 0

3 0

4 0

5 0

6 0

70

80

90

Next Nominal value

Next Category 5




MegaLine 524 SC


Insulation resistance (M ohm/km) 500 (min.)

Mutual capacitance (mF/m) 45 (nominal value)









500 (core/screen)




40

Meg

aLin

e5

MegaLine 524 SC Duplex


S/UTP 100 ohmTertiary area

Type: KS-02YS(St+C)H 2x(4x2xAWG 24/1)-100 ohmKS-02YS(St+C)Y 2x(4x2xAWG 24/1)-100 ohm

Structure

Conductor


Insulation

Cellular PE, Core ø: Nominal value 1.05 mm





Outer sheath

Halogen-free compound or PVC,figure 8 with seperator, 2 parallel basic elements


Overall screen


Marking

• KERPEN special MegaLine 524 SC 2x4P,


*H*, meter marking





EN 50167, EN 50169 and prEN 50288-2-1,

August 2000







Temperature range



Bending radius



Flame retardance

• Acc. to IEC 60332-1








2x(4x2xAWG 24/1) 6.0 x12.5 86 0.85 0.24 7KS007292x(4x2xAWG 24/1) 6.0x12.5 86 0.80 0.23 7KS00763


41


Frequency (MHz) 1.0 4.0 10.0 16.0 20.0 31.25 62.5 100.0 200.0

















1 10 100 1000MHz

dB

0

1 0

2 0

3 0

4 0

5 0

6 0

70

80

90

Next Nominal value

Next Category 5e

Attenuation Category 5e



MegaLine 524 SC Duplex


Insulation resistance (M ohm/km) 500 (min.)










500 (core/screen)




42

Meg

aLin

e5

MegaLine 526 SC flex


S/UTP 100 ohmWork area

Type: KS-02YS(St+C)H nx2xAWG 26/7-100 ohmKS-02YS(St+C)Y nx2xAWG 26/7-100 ohm

Structure

Conductor


Insulation



Colour codegr/or, bk/rd, gn/ye, bl/br

Cablingn pairs twisted together


Outer sheath



Overall screen


Marking

• KERPEN special MegaLine 526 flex “Number of pairs”,

for halogen-free version, additional marking: *H*





EN 50168 and prEN 50288-2-2, August 2000







Temperature range



Bending radius


Flame retardance

• Acc. to IEC 60332-1








2x2xAWG 26/7 5.0 30 0.30 0.08 7KS00772 7KS002704x2xAWG 26/7 5.7 35 0.29 0.08 7KS007734x2xAWG 26/7 5.7 35 0.31 0.09 7KS00248


43


Frequency (MHz) 1.0 4.0 10.0 16.0 20.0 31.25 62.5 100.0 200.0

















1 10 100 1000MHz

dB

0

1 0

2 0

3 0

4 0

5 0

6 0

70

80

90

Next Nominal value

Next Category 5




MegaLine 526 SC flex


Insulation resistance (M ohm x km) 500 (min.)










500 (core/screen)




44

Meg

aLin

e5

MegaLine 524 S

Communication cable 100 MHzBetter than the new Category 5e

S/UTP 100 ohmHorizontal area

Type: KS-02YS(ST)H nx2xAWG 24/1-100 ohmKS-02YS(ST)Y nx2xAWG 24/1-100 ohm

Structure

Conductor


Insulation

Cellular PE





Outer sheath



Overall screen

Aluminium bonded polyester tape in contactwith tinned copper wire AWG 24/1

Marking

• KERPEN special MegaLine 524 S “Number of pairs”,

for halogen-free version, additional marking: *H*





EN 50167, EN 50169 and prEN 50288-2-1,

August 2000







Temperature range



Bending radius



Flame retardance

• Acc. to IEC 60332-1

• halogen-free version:



• Acc. to IEC 60754-2/61034




4x2xAWG 24/1 5.9 37 0.45 0.13 7KS00649 7KS00354

45


Frequency (MHz) 1.0 4.0 10.0 16.0 20.0 31.25 62.5 100.0 200.0














Category 5* (min.) 60.8 48.7 40.8 36.7 34,7 30.9 24.8 20.8 n.def.

RL (dB) Nominal value 28.0 28.0 28.0 28.0 28.0 26.0 24.0 24.0 20.0


MHz

dB

0

1 0

2 0

3 0

4 0

5 0

6 0

70

Next Nominal value

Next Category 5



* according to prEN 50288-2-1, August 2000

MegaLine 524 S

DC resistance (ohm/km) 93.2 (max.)


Mutual capacitance (pF/km) 45 (nominal value)







500 (core/screen)




46

Meg

aLin

e5

MegaLine 526 S flex

Communication cable 100 MHzBetter than Category 5

S/UTP 100 ohmWorkplace

Type: KS-02YS(St)Y nx2xAWG 26/7-100 ohm

Structure

Conductor


Insulation

Cellular PE





Outer sheath

PVC


Overall screen

Aluminium bonded polyester tape with underlaid copper drain wire AWG 26/7

Marking

• KERPEN special MegaLine 526 S flex “Number of pairs“


• Workplace, device connection, patch panel

• Category 5 acc. to EN 50173, EN 50173 “2nd edition“,

ISO/IEC 11801, ISO/IEC 11801 “2nd edition“,

EN 50168 and prEN 50288-2-2, August 2000







Temperature range



Bending radius


Flame retardance

• Acc. to IEC 60332-1




2x2xAWG 26/7 4.6 18 0.30 0.08 7KS006004x2xAWG 26/7 5.0 26 0.35 0.10 7KS00601

47


Frequency (MHz) 1.0 4.0 10.0 16.0 20.0 31.25 62.5 100.0 200.0



Cross talk Nominal value 64.0 55.0 49.0 47.0 45.0 43.0 38.0 35.0 30.0


MHz1 10 100 1000

dB

0

1 0

2 0

3 0

4 0

5 0

6 0

70

Next Nominal value

Next Category 5



* Category 5

MegaLine 526 S flex





Propagation delay (ns/km) 4.26 (recommended value)



500 (core/screen)



attentuation (dB)


48

Office North-East, Olaf Faude

Soltauer Straße 8D-13509 Berlin

Tel.: +49/30/43 55 33 43Fax: +49/30/43 55 33 42

E-mail [email protected]

Indoor DutiesSimone Preuß

Tel.: +49/24 02/17-550Fax: +49/24 02/17-523


Office South-East, Volkmar Siegel

Reideburger Straße 42D-06116 Halle

Tel.: +49/3 45/5 60 82 35Fax: +49/3 45/5 60 57 34


Indoor DutiesSimone Preuß

Tel.: +49/24 02/17-550Fax: +49/24 02/17-523


Office South, Karlheinz Kuglmeier

Am Tiergarten 24D-96148 Baunach

Tel.: +49/95 44/98 02 62Fax: +49/95 44/98 02 63

Email [email protected]

Indoor DutiesCarina Nowak

Tel.: +49/24 02/17-407Fax: +49/24 02/17-523


Office South-West, Willy Teufel

Gündringer Straße 32D-72202 Nagold

Tel.: +49/74 59/40 51 56Fax: +49/74 59/40 51 57


Indoor DutiesUrania Kraus

Tel.: +49/24 02/17-398Fax: +49/24 02/17-523


Get

ting in t

ouch Your contacts at Kerpen special

Sales Germany

Sales Management

Jörg Bonkat

Tel.: +49 / 24 02 / 17-303

Fax: +49 / 24 02 / 17-521


Office North, Uwe Künzel

Schopbachweg 13 hD-22527 HamburgTel.: +49/40/54 76 66 90Fax: +49/40/54 76 66 91E-mail [email protected]

Indoor DutiesMichaela RadermacherTel.: +49/24 02/17-301Fax: +49/24 02/17-521E-mail [email protected]

Office Central, Knut Brodeßer

Holteyer Straße 51D-45289 EssenTel.: +49/2 01/57 19 66Fax: +49/2 01/8 57 52 18E-mail [email protected]

Indoor DutiesHeike DelheyTel.: +49/24 02/17-304Fax: +49/24 02/17-521Email [email protected]

Office West, Harald Kastner

Wiesenheegstraße 13D-63594 HasselrothTel.: +49/60 55/84 04 88Fax: +49/60 55/84 04 90E-mail [email protected]

Indoor DutiesMonika KöhnTel.: +49/24 02/17-302Fax: +49/24 02/17-521E-mail [email protected]

49

Austria

Ing. Ivo GodaiEnzenreitherstraße 6A-2640 GloggnitzTel.: +43/26 62/4 26 08Fax: +43/26 62/4 22 08Email [email protected]

Export Sales (Austria, Belgium,

Switzerland, Luxembourg, Netherlands,

Eastern Europe)

Sales Management

Gerd Backhaus

Tel.: +49/24 02/17-491

Fax: +49/24 02/17-522


Indoor Duties

Susanne Herwartz

Tel.: +49/24 02/17-485

Fax: +49/24 02/17-522


Export Sales (France, Great Britain,

Italy, Portugal, Spain and

other countries)

Sales Management

Jean-Pierre Schoenen

Tel.: +49/24 02/17-464

Fax: +49/24 02/17-522


Indoor Duties

Tatjana Hopf

Tel.: +49/24 02/17-270

Fax: +49/24 02/17-522


Great Britain

Pierre Sacré70, Stepping Stone Road

CV5 8 JU CoventryWarwickshire

Tel.: +44/24 76/59 25 39Fax: +44/24 76/59 25 39


Netherlands

Mark WijnenBenonilaan 3

NL-1695 HD Blokker (Hoorn)Tel.: +31/2 29/27 29 80Fax: +31/2 29/27 29 01


France

Pierre-Etienne Romette47 Rue Fernand Lafaye

F-03300 CussetTel.: +33/4/70 96 21 66Fax: +33/4/70 96 21 66


Spain

Tenmega S. A.Pedro IV, 464-466

E-08019 BarcelonaTel.: +34/93/30 36 900Fax: +34/93/30 87 709


Portugal

Tenmega Portugal S. A.Edificio Empresarial - Sala E1

Alameda António Sérgio, LT 161P-2795 Linda-A-Velha

Tel.: +3 51/1/41 55 330Fax: +3 51/1/41 55 339

50

Mega Line 5

MegaLine 524 SCMegaLine 524 SC DX

MegaLine 526 SC flexMegaLine 524 S

MegaLine 526 S flex

22.2 6.0 18.8 41.022.2 6.0 18.8 41.038.3* 32.1* 2.6** 41.022.5 8.5 18.5 41.031.1* 25.7* 4.30** 30.0

*ACR (db/10m)**Attenuation (db/10m)

MegaLine 6

MegaLine 6UEMegaLine 623

MegaLine 623 DXMegaLine 623 DS

MegaLine 623 DS DXMegaLine 627 flex

35.4 22.0 17.0 14.9 19.6 55.053.8 39.0 33.5 30.0 20.0 19.2 73.053.8 39.0 33.5 30.0 20.0 19.2 73.053.8 39.0 33.5 30.0 20.0 19.2 73.052.8 38.0 33.5 29.0 20.0 19.2 72.071.1* 64.8* 63.3* 60.8* 57.6* 2.9** 74.0

71.2 46.4 26.0 13.8 17.8 89.071.2 46.4 26.0 13.8 17.8 89.078.4* 68.2* 61.9* 54.5* 2.64** 81.071.1* 64.8* 63.3* 60.8* 57.6* 55.2* 2.9** 74.0

MegaLine 7

MegaLine 723MegaLine 723 DX

MegaLine 726 flexMegaLine 727 flex

74.6 61.0 42.0 4.0 15.4 90.0MegaLine 8

Electrical characteristics:

ACR (dB/100m) Attenuation NEXT(dB/100m) (dB/100m)

MHz 100 200 250 300 450 550 600 800 900 1200 at 100 MHz at 100 MHz

2

Ker

pen As an innovative, independent company in the cable industry, we develop, produce and

market cables according to German and international standards, factory specifications and

the wishes of the customer.

In the field of cables and systems for information technology, we are one of the market

leaders in Europe with the MegaLineTM product family. Besides copper data cables of

the MegaLineTM brand, our product portfolio in the IT field also includes the copper system

technology ELineTM. Since January 2000, we have been producing GigaLineTM optical fibre

cables to the highest possible standards at our factory in Stolberg. The FLineTM cabling

system for optical fibres rounds off the IT product portfolio. Data cables and systems from

Kerpen are used mainly for Local Area Networks in structured in-door cabling and in

Metropolitan Area Networks for the operating of city networks. For cables for measurement

and control technology and for plant engineering, Kerpen has an important position inter-

nationally. It manufactures and markets high-quality power cables, telecommunications

cables and special cables for mining, industry and energy providers.

All our activities aim at quality and customer satisfaction – these are the standards by

which we are judged. Committed and creative employees contribute their abilities to the

realisation of this goal. The quality management system certified according to DIN ISO

9001 in 1990 and the environmental management system certified according to DIN EN ISO

14001 in 1998 also exclusively meet the demands of our customers for economy, reliability

and flexibility. – We will continue to work in this direction in the future.

Who are we ... Conductor diameter AWG/metric

Mechanical characteristics:

Synopsis of products

Product:

Horizontal cable

Backbone cable

Distribution centre for storey

Primary cable

Distribution centre for building

Conductor diameter (AWG) Structure Wire Ø Conductor Ø

Number of wires Nominal value Nominal value






51

MegaLine 8

MegaLine 7

MegaLine 6

MegaLine 5

Dimensions External Ø Weight Calorific value Product no. Bandwidthmm kg/km Mj/m MHz

4x2xAWG 22/1 8.5 90 0.74 7KS01138 1200 Page 10

4x2xAWG 23/1 7.5 70 0.65 7KS00916 800 Page 142x(4x2xAWG 23/1) 7.5x15.2 136 1.40 7KS01100 800 Page 164x2xAWG 26/7 6.2 46 0.42 7KS01067 900 Page 184x2xAWG 27/7 5.8 34 0.35 7KS01189 600 Page 20

4x2xAWG 23/1 6.26 44 0.65 7KSO1375 300 Page 244x2xAWG 23/1 7.5 68 0.60 7KSOO533 450 Page 262x(4x2xAWG 23/1) 7.5x15.2 136 1.40 7KS00758 450 Page 284x2xAWG 23/1 7.2 57 0.75 7KS01167 450 Page 302x(4x2xAWG 23/1) 7.2x14.8 114 1.70 7KSO1336 7KSO1372* 450 Page 324x2xAWG 27/7 5.8 34 0.35 7KS01078 450 Page 34

4x2xAWG 24/1 6.0 44 0.38 0.40* 7KS00643 7KS00353* 200 Page 382x(4x2xAWG 24/1) 6.0x12.5 86 0.80 0.85* 7KS00763 7KS00729* 200 Page 404x2xAWG 26/7 5.7 35 0.29 0.31* 7KS00773 7KS00248* 250 Page 424x2xAWG 24/1 5.9 37 0.45 0.45* 7KS00649 7KS00354* 100 Page 444x2xAWG 26/7 5.0 26 0.35 7KS00601 100 Page 46

* for PVC version Other dimensions on request

Mega Line 5

MegaLine 524 SCMegaLine 524 SC DXMegaLine 526 SC flexMegaLine 524 SMegaLine 526 S flex

MegaLine 6

MegaLine 6UEMegaLine 623MegaLine 623 DXMegaLine 623 DSMegaLine 623 DS DXMegaLine 627 flex

MegaLine 7

MegaLine 723MegaLine 723 DXMegaLine 726 flexMegaLine 727 flex

MegaLine 8

Syn

opsis

53

CO

MP

ET

EN

CE

I

N

CA

BL

E

TE

CH

NO

LO

GY

Kerpen special GmbH & Co. KG · Zweifaller Straße 275-287 · D-52224 Stolberg

Phone: +49/24 02/17-1 · Fax: +49/24 02/7 51 54

E-Mail: [email protected] · http://www.kerpen.com

*************

MegaLine

Copper Data Cablesfor IT cabling

Important Definitions:

ACR*Attenuation Cross-talk Ratio – the difference between attenuationand cross-talk attenuation. The ACR is used as a measure for the ratioof signal power to disturbance power.

Attenuation*The ratio between the power received at the end of a pair and thepower fed in at the beginning. Attenuation is given as a power ratioin logarithmic form (dB).

Channel*Channel or the entire transmission circuit without the plug-in connec-tors on the terminal devices

Characteristic Wave Impedance*This is defined as the ratio between voltage and current. It is thecharacteristic value for a homogeneous cable and characterises thetransmission system. In conjunction with the return loss, the charac-teristic wave impedance describes the transmission circuit.

Cross-talk Attenuation*A measure for the ratio between the power launched unintentionallyinto pair x from pair y and that fed into pair y.

Delay*Delay in signal transmission of a pair and thus restriction of thetransmission rate. The signal delay causes frequency-dependent signaldistortion.

FEXT*Far End Cross-talk. A distinction is made between Input-Output FEXT(I/O FEXT) and Equal Level FEXT (EL-FEXT).

Input Impedance*A frequency-dependent value corresponding to the characteristic waveimpedance which takes the inhomogeneities of the cable intoaccount. A transmission circuit can be described via this value.

NEXT*Near End Cross-talk.

Permanent LinkThe cable link installed between the patch panel and the socket (TA)

Power Sum (PS)*The power sum describes the sum total of all disturbance power laun-ched into a pair due to cross-talk. Power sum measurement comesvery close to application for Gigabit Ethernet, in which all pairs are inoperation. The Power Sum can be formed for ACR NEXT and FEXT.

Return Loss (RL)*This value describes the inhomogeneities in terms of the ratio bet-ween the forward electromagnetic wave and the return wave.

Skew*The difference between the delay times of two or more pairs. Theskew (delay) must be as small as possible for special applications, forexample Gigabit Ethernet.

DW 2

040-

2 M

egaL

ine-

Bros

chür

e GB

03/

01

competence in cable technology - webzdarma · 2 kerpen as an innovative, independent company in the...

Documents