completion guide
TRANSCRIPT
-
7/29/2019 Completion Guide
1/77
WELL COMPLETION,MAINTENANCE AND
ABANDONMENT
GUIDELINENovember | 2012
Version 1.10
-
7/29/2019 Completion Guide
2/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.10
BC Oil & Gas Commission i
CONTENTS
MANUAL REVISIONS .............................................................................................. 1
SUMMARY OF REVISIONS............................................................................................... 1
1 PREFACE .............................................................................................................. 2
1.1 PURPOSE .......................................................................................................... 21.2 SCOPE.............................................................................................................. 21.3 HOW TO USE THIS MANUAL................................................................................. 31.4 ADDITIONAL GUIDANCE ...................................................................................... 3
1.4.1 Feedback .............................................................................................. 41.4.2 Frequently Asked Questions ................................................................. 4
2 WELL EQUIPMENT ............................................................................................... 5
2.1 WELLHEADS ...................................................................................................... 52.2 TUBING ............................................................................................................ 52.3 PACKERS........................................................................................................... 52.4 SUBSURFACE SAFETY VALVES ................................................................................ 62.5
OIL WELLS ........................................................................................................ 6
2.6 FENCING........................................................................................................... 72.7 LEAK DETECTION ................................................................................................ 7
3 WELL SERVICING OPERATIONS ............................................................................ 9
3.1 WELL SERVICING OPERATIONS.............................................................................. 93.2 COMPLETIONS /WORKOVERS /MAINTENANCE ....................................................... 9
3.2.1 Shallow Fracturing ............................................................................... 93.2.2 Commingling ...................................................................................... 10
3.3 WELL SUSPENSION ........................................................................................... 113.3.1 Definitions .......................................................................................... 113.3.2 Observation Wells .............................................................................. 113.3.3 Suspension Requirements .................................................................. 123.3.4 Packer Testing .................................................................................... 173.3.5 Long Term Inactive Wells ................................................................... 173.3.6 Reactivating Suspended Wells ........................................................... 173.3.7 Information / Reporting Requirements .............................................. 17
3.4 CLASSIFICATION OF LOW AND MEDIUM RISK GAS WELLS......................................... 193.5 WELL ABANDONMENT ...................................................................................... 20
4 WELL SERVICING EQUIPMENT AND PROCEDURES ............................................. 21
4.1 BLOWOUT PREVENTION..................................................................................... 214.1.1 Well Servicing Blowout Prevention .................................................... 214.1.2 BOP Equipment Classes ...................................................................... 214.1.3 General .............................................................................................. 21
4.1.4 Accumulator systems ......................................................................... 224.1.5 Requirements Specific to Class A Systems .......................................... 234.1.5 Requirements Specific to Class B and C Systems ................................ 234.1.6 Line Requirements ............................................................................. 234.1.7 Stabbing Valve ................................................................................... 244.1.8 Blowout Prevention Manifold ............................................................ 244.1.9 Testing of Blowout Prevention Equipment......................................... 244.1.10 Special Sour Wells ......................................................................... 25
-
7/29/2019 Completion Guide
3/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission ii
4.1.11 Slickline, Snubbing and Coil Tubing Operations ............................ 254.1.12 Hammer Unions ............................................................................ 254.1.13 Diagrams of Blowout Prevention Systems for Well Servicing ....... 26
4.2 PERSONNEL..................................................................................................... 314.3 FIRE PRECAUTIONS AND EQUIPMENT SPACING....................................................... 32
4.3.1 Engines ............................................................................................... 324.3.2
Fuel .................................................................................................... 32
4.3.3 Smoking ............................................................................................. 324.3.4 Recommended Spacing Distances...................................................... 334.3.5 Flare Stacks ........................................................................................ 344.3.6 Explosives ........................................................................................... 34
4.4 INCIDENT REPORTING........................................................................................ 344.5 CONCURRENT OPERATIONS ................................................................................ 34
5 ENVIRONMENTAL CONSIDERATIONS ................................................................ 35
5.1 SURFACE CASING VENT FLOWS ........................................................................... 355.1.1 Definitions .......................................................................................... 355.1.2 Checking for Surface Casing Vent Flows ............................................ 355.1.3 Testing and Reporting Surface Casing Vent Flows ............................. 365.1.4 Surface Casing Vent Flow Repairs ...................................................... 38
5.2 GAS MIGRATION .............................................................................................. 395.2.1 Definitions .......................................................................................... 39
5.3 CASING LEAKS AND FAILURES.............................................................................. 415.4 NOISE ............................................................................................................ 415.5 FLARING AND VENTING...................................................................................... 415.6 FLUID STORAGE ............................................................................................... 41
6 DATA SUBMISSION ............................................................................................ 42
6.1 COMPLETION/WORKOVER/ABANDONMENT REPORTS............................................. 426.1.1 Instructions for Completion of the Report ......................................... 42
6.2 WELL DELIVERABILITY TEST REPORTS ................................................................... 45
6.2.1 Well Deliverability Test Report Instructions ....................................... 456.3 OIL,GAS AND WATER ANALYSIS ......................................................................... 486.4 HYDRAULIC FRACTURING FLUID REPORTS.............................................................. 486.5 PRODUCTION LOGS........................................................................................... 48
7 COMPLIANCE ..................................................................................................... 50
OGAA ................................................................................................................ 50Drilling and Production Regulation .................................................................. 50
APPENDIX A: COMPLETION/WORKOVER REPORT GUIDELINES ............................ 51
APPENDIX B: WELL SUSPENSION/INSPECTION FORM INSTRUCTIONS .................. 53
APPENDIX C: NOTICE OF OPERATION / FLARE USER MANUAL .............................. 56
-
7/29/2019 Completion Guide
4/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 1
Manual Revisions
Summary of Revisions
The Well Completion, Maintenance and Abandonment Manualhas been revised based upon feedback to provide clarity interms of requirements and process. Structural changes bysection are highlighted below.
Applications received on or after the effective date will berequired to meet the revised application standards.
Effective Date Section Description/Rationale
1-Dec-2010 General Updated Links
1-Jan -2011 3 Changed the requirements for Wellbore Fluid in tables 3.2, 3.3 and 3.4
1-Feb-2011 1 Updated links and Feedback email address.
1-March-2011 General Updated formatting. No process changes.
1-May-2011 3 & 6Completion/Workover Reports. Included information provided in IL2011-05 and the Completion/Workover Report Submission Guide.
1-August-2011 General Updated page numbers
1-Sept-2011 7 Added Compliance section.
1- Nov-2011 GeneralUpdated links to BCOGC. Added Notice of Operation/Notice of Flare
User Manual to Appendix B.
1-Jan-2012 4 Updated Table 4.1: Recommended Spacing Distances
1-Feb-2012 6 Added Section 6.4: Data Submission
1-Jun-2012 Appendix B Updated Appendix B screen shots, p.52.
1-Jul-2012 Appendix B Added Well Suspension/Inspection Report Instructions, p. 52.
6
Added clarification to Section 6.3, p.48: samples must be taken prior to
or within six months. Added Section 6.5: Production Logs, p.48.
1-Dec-2012 6Updated Section 6.1, p. 42: Two signed copies to A signed copy.Removed: in duplicate, from the Completion/Workover Report Form.
-
7/29/2019 Completion Guide
5/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 2
1 Preface1.1 Purpose
This manual has been created to guide users through the BCOil and Gas Commission (the Commission) processes andprocedures. It also serves to highlight changes in process,procedure, requirements and terminology resulting from the Oiland Gas Activities Act (OGAA).
For users already familiar with the Commission applicationprocess, this manual provides a quick reference highlighting thesteps required to complete specific tasks. For users lessfamiliar, this manual presents a complete overview of
Commission requirements and provides links to more detailedmaterial.
This manual is not intended to take the place of the applicablelegislation. The user is encouraged to read the full text oflegislation and each applicable regulation and seek directionfrom Commission staff, if and when necessary, for clarification.
1.2 Scope
This manual focuses exclusively on requirements and
processes associated with the Commissions legislativeauthorities and does not provide information on legalresponsibilities that the Commission does not regulate. It is theresponsibility of the applicant or permit holder to know anduphold its other legal responsibilities. Examples of legalresponsibilities outside of this manual include obligations underthe Federal Fisheries Act, the Transportation Act, the Highway
Act, the Workers Compensation Act, and the Wildlife Act.
-
7/29/2019 Completion Guide
6/77
-
7/29/2019 Completion Guide
7/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 4
Other navigational and illustrative elements used in the manualinclude:
Hyperlinks:Hyperlinked items appear as blue, underlined text. Clicking on ahyperlink takes the user directly to a document or location on a
webpage.
Sidebars:Sidebars highlight important information such as a change fromthe old procedure, new information, or reminders and tips.
Figures:Figures illustrate a function or process to give the user a visualrepresentation of a large or complex item.
Tables:Tables organize information into columns and rows for quickcomparison.
1.4.1 FeedbackThe Commission is committed to continuous improvement bycollecting information on the effectiveness of guidelines andmanuals. Clients and stakeholders wishing to comment onCommission guidelines and manuals may send constructivecomments [email protected].
1.4.2 Frequently Asked QuestionsAFrequently Asked Questions(FAQ) link is available on theCommission OGAA website. The information provided iscategorized into topics which reflect the manuals for easyreference.
mailto:[email protected]:[email protected]:[email protected]://www.bcogc.ca/OGAA/faq.aspxhttp://www.bcogc.ca/OGAA/faq.aspxhttp://www.bcogc.ca/OGAA/faq.aspxhttp://www.bcogc.ca/OGAA/faq.aspxmailto:[email protected] -
7/29/2019 Completion Guide
8/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 5
2 Well EquipmentThe well equipment section outlines the regulatory requirements
for well equipment in theDrilling and Production Regulation.
2.1 Wellheads
[Section 17, Drilling and Production Regulation]
Wellheads are required to operate safely under the conditionsanticipated during the life of the well and the wellhead is not tobe subjected to excessive force.
Refer to Enform Publications Industry Recommended Practice(IRP) Volume #5 (IRP 5 Minimum Wellhead Requirements) for
more information.
2.2 Tubing
[Section 16, Drilling and Production Regulation]
Tubing is required for the production of gas containing 5%hydrogen sulphide (H2S) and for all injection and disposalexcept for the injection of fresh water.
2.3 Packers
[Sections 16 and 39, Drilling and Production Regulation]
A production packer must be used for: All injection and disposal except for the injection of fresh
water and
Wells containing gas with > 5% H2S, or if a numberedhighway or populated area is located within the emergencyplanning zone for the well.
Populated area means a dwelling, school, picnic ground or
other place of public concourse.Annual packer isolation testing is required for all wells whereinstallation of a production packer is required. If a packer testfails, the permit holder must complete repairs without
http://www.bclaws.ca/EPLibraries/bclaws_new/document/ID/freeside/536427494http://www.bclaws.ca/EPLibraries/bclaws_new/document/ID/freeside/536427494http://www.bclaws.ca/EPLibraries/bclaws_new/document/ID/freeside/536427494http://enform.ca/media/93722/irp05_draft_rev19_june2010.pdfhttp://enform.ca/media/93722/irp05_draft_rev19_june2010.pdfhttp://enform.ca/media/93722/irp05_draft_rev19_june2010.pdfhttp://enform.ca/media/93722/irp05_draft_rev19_june2010.pdfhttp://enform.ca/media/93722/irp05_draft_rev19_june2010.pdfhttp://enform.ca/media/93722/irp05_draft_rev19_june2010.pdfhttp://www.bclaws.ca/EPLibraries/bclaws_new/document/ID/freeside/536427494 -
7/29/2019 Completion Guide
9/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 6
unreasonable1 delay.
Refer to the Alberta Energy and Resources Conservation Board(ERCB) Interim DirectiveID 2003-01for recommended packertesting procedures.
The permit holder is required to maintain a record of all packerisolation tests and repairs. This information must be submittedto the Commission on request.
2.4 Subsurface Safety Valves
[Section 39, Drilling and Production Regulation]
Subsurface safety valves are required for wells containing gaswith > 5% H2S if: A major highway or populated area is located within the
emergency planning zone for the well
The well is located within 800 m of a populated area or 8km of a town, city or village and
The well could produce > 30 000 m3 of gas per day
In general, the distance from a city, town or village should bemeasured from the corporate limits. In cases where thecorporate limits do not reasonably correspond with theboundaries of the community, the permit holder may take afunctional approach such as delineation of the extent ofdeveloped areas.
2.5 Oil Wells
[Section 39, Drilling and Production Regulation]
Oil wells completed after September 13, 2010 equipped with anartificial lift, if the H2S content of the gas exceeds 100 ppm,must install the following An automatic shutdown on the stuffing box that will shut
down the pumping unit in the event of a stuffing box orpolish rod failure and
An automatic vibration shutdown system
1 In general, all repairs should be completed within 90 days. Reasonabledelays are acceptable in cases where access is seasonal and the delay doesnot result in a risk to safety or the environment. Delays that extend past thenext seasonal access window are not reasonable (greater than one year).
http://www.ercb.ca/portal/server.pt/gateway/PTARGS_0_0_323_253_0_43/http%3B/ercbContent/publishedcontent/publish/ercb_home/industry_zone/rules__regulations__requirements/information_letters__interim_directives/interim_directives__id_/id2003_01.aspxhttp://www.ercb.ca/portal/server.pt/gateway/PTARGS_0_0_323_253_0_43/http%3B/ercbContent/publishedcontent/publish/ercb_home/industry_zone/rules__regulations__requirements/information_letters__interim_directives/interim_directives__id_/id2003_01.aspxhttp://www.ercb.ca/portal/server.pt/gateway/PTARGS_0_0_323_253_0_43/http%3B/ercbContent/publishedcontent/publish/ercb_home/industry_zone/rules__regulations__requirements/information_letters__interim_directives/interim_directives__id_/id2003_01.aspxhttp://www.ercb.ca/portal/server.pt/gateway/PTARGS_0_0_323_253_0_43/http%3B/ercbContent/publishedcontent/publish/ercb_home/industry_zone/rules__regulations__requirements/information_letters__interim_directives/interim_directives__id_/id2003_01.aspx -
7/29/2019 Completion Guide
10/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 7
2.6 Fencing
[Section 39, Drilling and Production Regulation]
Permit holders of completed wells that:
Are located within 800 m of a populated area or Have a populated area within the emergency planning
zone for the well
Fencing or other measures to prevent unauthorized access tothe well must be installed in these circumstances.
Fencing or other forms of access control must be proportional tothe potential for unauthorized access to the wellsite. Accesscontrol may include fencing of the wellsite, or gating the accessroad. If the well is located in an access-controlled area, noadditional measures may be required. For wells that are located
on private land, the method of access control should bedeveloped in consultation with the landowner.
2.7 Leak Detection
[Section 39, Drilling and Production Regulation]
All completed wells must be equipped with a system to detectand control leaks as quickly as practicable.
The Commission expects that leak detection systems will be
proportional to the consequences that may result from a leak.Leak detection may range from fully automated shutdownsystems to periodic inspections.
If an uncontrolled flow from a completed well could produce ahydrogen sulphide concentration in atmosphere greater than100 ppm at a distance of 50 metres from the well, the permitholder must install and maintain: An automated shutdown system and
A hydrogen sulphide detection, alarm and automatedshutdown system if the well is located within 1600 metres
of a populated areaFor wells completed prior to October 4, 2010, H2S detection andautomated shutdown systems are not required until
January 1, 2012 and the permit holder may apply for anexemption to the requirement.
-
7/29/2019 Completion Guide
11/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 8
The following formula may be used to calculate the absoluteopen flow rate of a well that will result in an H2S concentration inatmosphere of 100 ppm at a point 50 metres from the well:
Wellhead AOF (103m3/day) = 147 000 / H2S (ppm)
or
Wellhead AOF (103m3/day) = 14.7 / H2S (mol %)
-
7/29/2019 Completion Guide
12/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 9
3 Well Servicing OperationsThe well servicing operations section outlines and explains therequirements for the reporting of servicing, suspension,
reactivation or abandonment of wells. It also outlines thenotification requirements for completions, workovers andmaintenance of wells.
3.1 Well Servicing Operations
[Section 39, Drilling and Production Regulation]
A permit holder must ensure that an adequate EmergencyResponse Plan is in place before conducting well servicingoperations. Refer to theEmergency Response PlanRequirements documentor contact the Commission EmergencyResponse and Safety Department for more information.
3.2 Completions / Workovers / Maintenance
[Section 24, Drilling and Production Regulation]
A Notice of Operations must be submitted to the Commission atleast 24 hours prior to the start of all completion, workover orabandonment operations. An approved Application to Alter is nolonger required for completion or workover operations.
All notifications must be submitted using the Online ReportingSystem. Refer to Appendix B for the instruction manual.
SeeSection 6.1for Completion/Workover Report submissionrequirements.
3.2.1 Shallow Fracturing
[Section 21, Drilling and Production Regulation]
Fracturing operations conducted at a depth of 600 metres orless must be approved in the well permit. Applications forshallow fracturing operations should include: The fracture program design including proposed pumping
rates, volumes, pressures, and fracturing fluids
Estimation of the maximum fracture propagation
http://www.bcogc.ca/documents/guidelines/BC_OGC_Emergency_Response_Plan_requirements.pdfhttp://www.bcogc.ca/documents/guidelines/BC_OGC_Emergency_Response_Plan_requirements.pdfhttp://www.bcogc.ca/documents/guidelines/BC_OGC_Emergency_Response_Plan_requirements.pdfhttp://www.bcogc.ca/documents/guidelines/BC_OGC_Emergency_Response_Plan_requirements.pdfhttp://www.bcogc.ca/documents/guidelines/BC_OGC_Emergency_Response_Plan_requirements.pdfhttp://www.bcogc.ca/documents/guidelines/BC_OGC_Emergency_Response_Plan_requirements.pdf -
7/29/2019 Completion Guide
13/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 10
Assessment of groundwater resources in the area
Identification and depth of all wells within 200 metres of theproposed shallow fracturing operations
Verification of cement integrity through available publicdata of all wells under the Commissions jurisdiction within
a 200 metre radius of the well to be fractured
Notification of water well owners within 200 metres of theproposed fracturing operations
The depth of bedrock and
Assessment of the suitability of the candidate well for theproposed fracturing operations including casing andcement integrity
Refer to theWell Permit Application Manualfor moreinformation on well permit applications and amendments.
3.2.2 Commingling
[Section 23, Drilling and Production Regulation]
All zones in a well must remain segregated unless permissionhas been granted for commingled production. Permission maybe granted in an individual well permit or by a special project forcommingling under section 75 of OGAA. The Commission hasdesignated certain areas where commingling is authorized,subject to certain conditions, including: Deep basin
Plains and Northern Foothills
Outer Foothills
For more information, refer to the Commingling section withinthe CommissionsResource Conservation Forms andGuidelinespage.
TheNotification of Commingled Well Productionform must besubmitted to the Commission within 30 days of thecommencement of commingled production.
http://www.bcogc.ca/document.aspx?documentID=874&type=.pdfhttp://www.bcogc.ca/document.aspx?documentID=874&type=.pdfhttp://www.bcogc.ca/document.aspx?documentID=874&type=.pdfhttp://www.bcogc.ca/industryzone/forms/resourceconservation.aspxhttp://www.bcogc.ca/industryzone/forms/resourceconservation.aspxhttp://www.bcogc.ca/industryzone/forms/resourceconservation.aspxhttp://www.bcogc.ca/industryzone/forms/resourceconservation.aspxhttp://www.bcogc.ca/document.aspx?documentID=637&type=.dochttp://www.bcogc.ca/document.aspx?documentID=637&type=.dochttp://www.bcogc.ca/document.aspx?documentID=637&type=.dochttp://www.bcogc.ca/document.aspx?documentID=637&type=.dochttp://www.bcogc.ca/industryzone/forms/resourceconservation.aspxhttp://www.bcogc.ca/industryzone/forms/resourceconservation.aspxhttp://www.bcogc.ca/document.aspx?documentID=874&type=.pdf -
7/29/2019 Completion Guide
14/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 11
3.3 Well Suspension
[Section 25, Drilling and Production Regulation]
3.3.1 DefinitionsActivity means
(a) production, injection, or disposal of fluids,(b) drilling, completion or workover operations and(c) reservoir pressure observation.
Inactive Well means a well that has not been abandoned but(a) has not been active for 12 consecutive months or(b) if the well is classified as a special sour well or an acid
gas disposal well and has not been active for 6
consecutive months.
For active production, injection and disposal wells, the date oflast activity is defined as the first day of the month following thelast month for which production, injection and disposal volumeswere reported.
Observation wells are deemed to be active (see ObservationWellssection).
For drilling activity, including new wells and re-entries, the dateof last activity is defined as the rig release date.
For completion and workover activity, the date of last activity isdefined as the completion date.
A permit holder may apply to the Commission to declassify aspecial sour well.
3.3.2 Observation Wells
Inactive wells offer good opportunities to monitor reservoirbehaviour, specifically, pool pressures over time. Tests of thesewells do not require shutting in producing wells to obtain
pressure information and can provide accurate sampling points.Wells with an operational status of Observation must be testedand aReservoir Pressure Survey Test Reportmust besubmitted to the Commission Resource ConservationDepartment at least once every two years.
http://www.bcogc.ca/document.aspx?documentID=620&type=.pdfhttp://www.bcogc.ca/document.aspx?documentID=620&type=.pdfhttp://www.bcogc.ca/document.aspx?documentID=620&type=.pdfhttp://www.bcogc.ca/document.aspx?documentID=620&type=.pdf -
7/29/2019 Completion Guide
15/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 12
A well may be classified as Observation by submission of aBC-11 form (Notice of Commencement or Suspension ofOperations) to the Ministry of Finance. A brief statementindicating what the well will be used to monitor should beincluded in the comments section.
Observation wells are treated as active and do not requiresuspension unless declassified.
Observation wells will be declassified if pressure data isnot submitted within 12 months of its due date.
Upon declassification, observation wells will be reclassifiedaccording to the well operation status (i.e. Gas Production)that existed prior to their classification as observation wellsand will require suspension.
For observation wells that have been declassified, the dateof last activity is the due date of the last pressure test
survey report.
3.3.3 Suspension Requirements
All wells must be suspended within 60 days of attaining inactivestatus in a manner that ensures the ongoing integrity of the well.
Any well may be suspended to a higher standard than theminimum requirements described in Tables 1 to 4. Reportingrequirements are outlined in theInformation and ReportingRequirementssection.
If all zones in a non-special sour well are abandoned and thewell has not yet been surface abandoned, the well shall becategorized as Low Risk - All cased wells (no perforations oropen hole).
Permit holders may apply to the Commission Drilling andProduction Department for an extension of a deadline.
The following tables describe the Commissions minimumrequirements for each category.
-
7/29/2019 Completion Guide
16/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 13
Table 3.1: General Requirements for All Inactive Wells
WellheadsUnperforated wells may use a welded steel plate atop the production casing stub.The plate must provide access to the wellbore for pressure measurement. All otherwells must use standard wellheads as described inIRP2andIRP5(draft).
Wellhead
Maintenance
There shall be no wellhead leaks.Bullplugs or blind flanges with needle valves must be installed on all outlets exceptthe surface casing vent.
The surface casing vent valve must be open and the surface casing ventunobstructed unless otherwise exempted by an official.
All valves must be chained and locked or valve handles must be removed.
The flowline must be disconnected from the wellhead.
Polish rod removal is not required to suspend low risk oil wells as long as the polishrod remains connected to the pump jack.
Pressure testing of the wellhead sealing elements refers to the primary and
secondary seals only, as applicable. For wellheads that do not have adequate testports, pressure tests may be omitted and visual observation for leaks is acceptable.An explanatory note must be included on the well suspension report.
Surface
Casing Vent
Flows
Surface casing vent flows are to be managed and reported in accordance withCommission requirements.
Lease
Maintenance
A sign stating the wells surface location, current permit holder, the currentpermit holders emergency contact number and appropriate warning symbolsas defined in Section 17 of the Drilling and Production Regulation must be inplace.
An area of 10 metres radius around the wellhead must be maintained toprevent brush from growing and causing a fire hazard.
Noxious weeds must be controlled.
Visual
Inspection
A visual inspection of the lease and wellhead must be conducted at least yearly toobserve for wellhead integrity, noxious weeds and other hazards.
For wells with helicopter access, the visual inspection frequency is the pressuretesting / monitoring frequency.
Reporting
Submit a BC-11 to the Ministry of Finance as outlined in Section 8.2.
A Suspension Report must be submitted to the Commission within 30 days ofthe completion of suspension operations.
Records of inspections must be maintained on file and if requested, be madeavailable to the Commission for review.
http://enform.ca/media/3583/irp2_final_2007.pdfhttp://enform.ca/media/3583/irp2_final_2007.pdfhttp://enform.ca/media/3583/irp2_final_2007.pdfhttp://enform.ca/media/93722/irp05_draft_rev19_june2010.pdfhttp://enform.ca/media/93722/irp05_draft_rev19_june2010.pdfhttp://enform.ca/media/93722/irp05_draft_rev19_june2010.pdfhttp://enform.ca/media/93722/irp05_draft_rev19_june2010.pdfhttp://enform.ca/media/3583/irp2_final_2007.pdf -
7/29/2019 Completion Guide
17/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 14
Table 3.2: Requirements Specific to Inactive High Risk Wells
2If applicable, install a bridge plug or packer and tubing plug within 100
metres of the liner top on uncompleted special sour wells.
Well Types
Type 1: Special sour wells2.
Type 2: Acid gas disposal wells.
Suspension Options Option A Option B
DownholeRequirements
Bridge plug or packer andtubing plug.
Bridge plug capped with 8 mlineal of cement.
Pressure Testing /Monitoring / Servicing
Requirements
Pressure test both tubing andannulus to 7 MPa for 10minutes.
Service and pressure testwellhead sealing elements.
Pressure test the casing to 7MPa for 10 minutes.
Service and pressure testwellhead sealing elements(if applicable).
Pressure Testing /
Monitoring / ServicingFrequency
At the time of suspension andthen annually. At the time of suspension andthen every 5 years.
Wellbore Fluid
Wellbore must be filled withnon-saline water or corrosioninhibited water. The upperportion of the wellbore mustbe protected from freezing.Freeze protection may beaccomplished by theplacement of at least 2 m of asuitable, non-freezing fluid at
surface.
Wellbore must be filled with non-saline water or corrosioninhibited water. The upperportion of the wellbore must beprotected from freezing. Freezeprotection may be accomplishedby the placement of at least 2 mof a suitable, non-freezing fluid at
surface.
-
7/29/2019 Completion Guide
18/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 15
Table 3.3: Requirements Specific to Inactive Medium Risk Wells
3Flowing oil wells are oil wells with sufficient reservoir pressure to sustain
flow against atmospheric pressure without artificial lift. The flowing product isa fluid.
Well Types
Type 1: Medium risk gas wells (seeSection 3.4).
Type 2: Non-flowing oil wells 50 mol/kmol H2S.
Type 3: Flowing oil wells3.
Type 4: All injection and disposal wells except for acid gasdisposal wells.
Type 6: Completed low risk wells that have been inactive orsuspended for at least 10 consecutive years.
Suspension
OptionsOption A (All types) Option B (All types) Option C (Type 6 Only)
Downhole /
Wellhead
Requirements
Packer and tubing plug. Bridge plug. Dual master valves.
Pressure Testing /
Monitoring /
Servicing
Requirements
Pressure test both thetubing and annulus to 7MPa for 10 minutes.
Service and pressuretest wellhead sealingelements.
Pressure test thecasing to 7 MPa for 10minutes.
Service and pressuretest wellhead sealingelements.
Read and record shut-intubing pressure (ifapplicable) and shut-incasing pressure.
Service and pressure testwellhead sealing
elements.
Pressure Testing /
Monitoring /
ServicingFrequency
At the time of
suspension and thenevery 3 years.
At the time of
suspension and thenevery 5 years.
At the time of suspension
and then annually.
Wellbore Fluid
Wellbore must be filledwith non-saline water orcorrosion inhibitedwater. The upperportion of the wellboremust be protected from
freezing. Freezeprotection may be
accomplished by the
placement of at least 2m of a suitable, non-freezing fluid at surface.
Wellbore must be filledwith non-saline water orcorrosion inhibitedwater. The upperportion of the wellboremust be protected from
freezing. Freezeprotection may be
accomplished by the
placement of at least 2m of a suitable, non-freezing fluid at surface.
None.
-
7/29/2019 Completion Guide
19/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 16
Table 3.4: Requirements Specific to Inactive Low Risk Wells
4Non-flowing oil wells are oil wells without sufficient reservoir pressure to
sustain flow against atmospheric pressure without artificial lift. The flowingproduct is a fluid. Removal of polish rods is not required to suspend low-riskoil wells as long as the polish rod remains connected to the pump jack.
Well Types
Type 1: All non-special sour cased wells (no perforations or openhole sections).
Type 2: Low risk gas wells (see Section 3.4).
Type 3: Water source wells. Type 5: Non-flowing
4oil wells < 50 mol/kmol H2S.
SuspensionOptions
Option A
(Types 2,3 and 5 only)
Option B
(Type 1 only)
Downhole
RequirementsNone. None.
Pressure Testing
/ Monitoring /ServicingRequirements
Read and record shut-in tubingpressure (if applicable) and shut-in
casing pressure.Service and pressure testwellhead sealing elements.
Pressure test casing to 7 MPa for 10minutes.
Service and pressure test wellheadsealing elements (if applicable).
Pressure Testing
/ Monitoring /ServicingFrequency
At the time of suspension andthen every 5 years.
At the time of suspension and then every 5years.
Wellbore Fluid None.
Wellbore must be filled with non-salinewater or corrosion inhibited water. Theupper portion of the wellbore must be
protected from freezing. Freeze protectionmay be accomplished by the placement ofat least 2 m of a suitable, non-freezingfluid at surface.
-
7/29/2019 Completion Guide
20/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 17
3.3.4 Packer Testing
Wells that require installation and yearly testing of a productionpacker are exempt from the testing requirements if the well issuspended in accordance with the Drilling and Production
Regulation.
3.3.5 Long Term Inactive Wells
All completed low-risk wells must meet medium risk suspensionrequirements after being suspended for 10 consecutive years.
For example, a completed low-risk well that last reportsproduction in December 2008 would be classed as inactive onDecember 31, 2009 and the Operator would have 60 days tosuspend the well in accordance with low-risk suspensionrequirements. If the well was still suspended on December 31,
2019, the Operator would have 60 days to suspend the well inaccordance with medium risk suspension requirements.
3.3.6 Reactivating Suspended Wells
The following are the procedures for the reactivation of asuspended well:
All Wells: Inspect, service and pressure test the wellhead
Inspect and service control systems and lease facilities
Report the reactivation through submission of a BC-11
form to the Ministry of FinanceMedium and High-Risk Wells: Pressure test the casing to 7 MPa for 10 minutes
(if applicable). If the test fails, investigate and repair theproblem
Pressure test the tubing (if present) to 7 MPa for 10minutes. If the test fails, investigate and repair the problem
3.3.7 Information / Reporting Requirements
3.3.7.1 Oil and Gas Commission
Suspensions
AWell Suspension/Inspection Formmust be submitted to theCommission, Drilling and Production Department within 30 daysof suspension of a well.
-
7/29/2019 Completion Guide
21/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 18
The suspension report may be submitted as a paper copy or inspreadsheet form.
Reactivations
Submission of a reactivation report is not required.Reactivations are identified by alternate means (i.e. spud date,production reporting).
Inspections
Records of inspections must be provided to the Commission onrequest.
Inspection results may be recorded by filling out the applicablesections of theWell Suspension/Inspection Formor through thepermit holders internal database. If an internal inspectionsdatabase is used, it is the permit holders responsibility toensure that the required information is recorded.
3.3.7.2 Ministry of Finance
The formNotice of Commencement or Suspension ofOperations: BC-11must be submitted to the Ministry of Financeon or before the 20th day of the calendar month following thecalendar month in which the following operations occurred at awell: Testing operations at a well prior to its being tied in to a
gas gathering system
Initial commencement of production
Initial commencement of injection or disposal
Suspension of production
Suspension of injection or disposal
Resumption of production
Resumption of injection or disposal
A separate BC-11 is required for each well or completed zonewithin a well. A single form may be completed if a well has both
a production and a service status in a production month, or if thestatus changes more than once in a production month (forexample testing and producing)
http://www.sbr.gov.bc.ca/documents_library/forms/BC11guidelines.pdfhttp://www.sbr.gov.bc.ca/documents_library/forms/BC11guidelines.pdfhttp://www.sbr.gov.bc.ca/documents_library/forms/BC11guidelines.pdfhttp://www.sbr.gov.bc.ca/documents_library/forms/BC11guidelines.pdfhttp://www.sbr.gov.bc.ca/documents_library/forms/BC11guidelines.pdfhttp://www.sbr.gov.bc.ca/documents_library/forms/BC11guidelines.pdf -
7/29/2019 Completion Guide
22/77
-
7/29/2019 Completion Guide
23/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 20
3.5 Well Abandonment
[Section 26, Drilling and Production Regulation]
For drilling wells, notification is not required prior to conductingopen hole plugbacks or abandonments.
Drilling wells that are downhole, but not surface abandoned atthe time of rig release, are not considered abandoned. Anabandonment notification and abandonment report must besubmitted to the Commission at the time of surfaceabandonment as outlined below for the well status to bechanged to abandoned.
Notification is required 7 days prior to conducting all other well
abandonments; however the notification requirement may bewaived on a case by case basis. An abandonment programmust be included with the notification.
Wells must be abandoned in a manner that ensures: Adequate hydraulic isolation between porous zones
Fluids will not leak from the well
Excessive pressure will not build up in any portion of thewell
The long-term integrity of the wellbore is maintained
Permit holders are expected to conduct abandonments andplugbacks in accordance with theERCB Directive 20. If there isany doubt about the adequacy of a plugging or abandonmentprogram, the permit holder should discuss their plans with theCommission. Failure to adequately plug or abandon a well mayresult in an order for remedial work.
Abandonment reports may be submitted using aCompletion/Workover Report Form.
http://www.ercb.ca/docs/documents/directives/directive020.pdfhttp://www.ercb.ca/docs/documents/directives/directive020.pdfhttp://www.ercb.ca/docs/documents/directives/directive020.pdfhttp://www.bcogc.ca/document.aspx?documentID=668&type=.dochttp://www.bcogc.ca/document.aspx?documentID=668&type=.dochttp://www.bcogc.ca/document.aspx?documentID=668&type=.dochttp://www.ercb.ca/docs/documents/directives/directive020.pdf -
7/29/2019 Completion Guide
24/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 21
4 Well Servicing Equipment and ProceduresThe well servicing equipment and procedures section outlinesand explains blowout prevention standards, personnel
requirements and fire precautions that permit holders mustfollow to comply with the Drilling and Production Regulation.
4.1 Blowout Prevention
[Part 4, Division 2, Drilling and Production Regulation]
4.1.1 Well Servicing Blowout Prevention
The following section outlines blowout prevention standards thata permit should follow to comply with the requirements of Part 4,Division 2 of the Drilling and Production Regulation. It is theresponsibility of the permit holder to ensure that blowoutprevention equipment and procedures are adequate.
A permit holder may use alternate blowout preventionequipment and techniques if they can demonstrate by means ofa detailed engineering analysis that the alternate equipment ortechniques are adequate as required by section 16(1) of theDrilling and Production Regulation.
4.1.2 BOP Equipment Classes
For the purposes of well servicing, blowout prevention
equipment classes are as follows:
Class A equipment is required for a well where the minimumpressure rating of the production casing flange is less than orequal to 21 000 kilopascals (kPa) and the hydrogen sulphidecontent in a representative sample of the gas is less than 10mol %;
Class B equipment is required for a well where the minimumpressure rating of the production casing flange is:
a) greater than 21 000 kPa, or
b) less than or equal to 21 000 kPa and the hydrogensulphide content in a representative sample of the gas is10 mol % or greater
Class C equipment is required for a special sour well.
4.1.3 General
-
7/29/2019 Completion Guide
25/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 22
At all times during well servicing, the well must be under control,adequate blowout prevention equipment must be installed andmust be able to shut off flow from the well regardless of the typeor diameter of tools or equipment in the well.
The blowout prevention equipment must have a pressure rating
equal to or greater than the pressure rating of the productioncasing flange or the formation pressure, whichever is the lesser.
Hydraulic ram type blowout preventers which are not equippedwith an automatic ram locking device must have hand wheelsavailable.
An accurate pressure gauge to determine the well annuluspressure during a well shut-in must be either installed or readilyaccessible for installation.
A service rig used at the well site must have an operable hornon the drilling control panel for sounding alerts.
A sour service separator and flare system, including appropriatemanifolding, must be used to process sour well effluent.
The well control system must be adequately illuminated.
4.1.4 Accumulator systems
All blowout preventers must be hydraulically operated andconnected to an accumulator system.
The accumulator system must be installed and operated in
accordance with the manufacturer's specifications. The systemmust be:
a) Connected to the blowout preventers with lines ofworking pressure equal to the working pressure of thesystem, and within 7 metres of the well, the lines must beof steel construction unless completely sheathed withadequate fire resistant sleeving
b) Capable of providing, without recharging, fluid ofsufficient volume and pressure to effect full closure of allpreventers, and to retain a pressure of 8 400 kPa on theaccumulator system
c) Recharged by a pressure controlled pump capable ofrecovering the accumulator pressure drop resulting fromfull closure of all preventers within 5 minutes
d) Capable of closing any ram type preventer within 30seconds
e) Capable of closing the annular preventer within 60seconds
-
7/29/2019 Completion Guide
26/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 23
f) Equipped with readily accessible fittings and gauges todetermine the pre-charge pressure
g) Equipped with a check valve between the accumulatorrecharge pump and the accumulator and
h) Connected to a nitrogen supply capable of closing all
blowout preventers installed on the well
The accumulator nitrogen supply must:a) Be capable of providing sufficient volume and pressure to
fully close all preventers and to retain a minimumpressure of 8 400 kPa, and
b) Have a gauge installed, or readily available forinstallation, to determine the pressure of each nitrogencontainer
4.1.5 Requirements Specific to Class A Systems
Class A blowout prevention systema) May utilize the rig hydraulic system to recharge the
accumulator andb) Must have operating controls for each preventer in a
readily accessible location near the operator's positionand an additional set of controls located a minimum of7 meters from the well
4.1.5 Requirements Specific to Class B and C SystemsClass B and Class C blowout prevention system must have:
a) An independent accumulator system with operating
controls for each preventer located at least 25 metresfrom the well, shielded or housed to protect the operatorfrom flow from the well
b) An additional set of controls in a readily accessiblelocation near the operator's position and
c) Working spools with flanged outlets
4.1.6 Line Requirements
The following requirements do not apply to snubbing units andservice rigs completing rod jobs.
A blowout prevention system must have two lines, one forbleeding off pressure and one for killing the well, which must:
a) Be either steel or flexible sheathed hose to provideadequate fire resistant rating
b) Be valved and have a working pressure equal to orgreater than that required for the blowout preventionequipment
-
7/29/2019 Completion Guide
27/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 24
c) Have one line connected to the rig pump and one lineconnected to the tank
d) Have one line connected to an outlet below the blowoutpreventers and the necessary equipment to readilyconnect the second line to the tubing
e) Be at least 50 mm nominal diameter andf) Be securely tied down
4.1.7 Stabbing Valve
A full opening ball valve (stabbing valve) which can be attachedto the tubing or other pipe in the well must:
a) Be ready for use and located in a readily accessiblelocation on the service rig
b) Be maintained in the open positionc) Have an internal diameter equal to or greater than the
smallest restriction inside the tubing or casing and
d) Be kept clean and ice free
4.1.8 Blowout Prevention Manifold
The blowout prevention system must include a manifold that:a) Consists of an arrangement of valves and steel lines that
have a working pressure greater than or equal to that ofthe blowout prevention system installed on the well
b) Contains a check valve to prevent flow from well to rigpump
c) Contains a pressure relief valve upstream of the check
valved) Is equipped with an accurate pressure gauge which shallbe either installed or readily accessible for installation
4.1.9 Testing of Blowout Prevention Equipment
Before commencing servicing operations at a well, a 10-minutepressure test must be conducted on:
a) Each ram preventer to 1400 kPa, prior to the testsdescribed in (b) and (c)
b) Each ram preventer, the full opening safety valve and theconnection between the stack and the wellhead, tested to
the wellhead pressure rating or the formation pressure,whichever is less
c) Each annular preventer to 7000 kilopascals or theformation pressure, whichever is less
Note: For an annular type blowout preventer, all mechanical andpressure tests required under subsection (c) must be conductedwith pipe in the blowout preventer.
-
7/29/2019 Completion Guide
28/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 25
All blowout prevention equipment, except for shear rams onspecial sour wells, must be mechanically tested daily, ifoperationally safe to do so; any equipment found defective mustbe made serviceable before operations are resumed.
All tests must be reported in the servicing log book and in the
case of a pressure test, the report must state the blowoutpreventer tested, the test duration and the test pressureobserved at the start and finish of each test.
At least once every three years, all blowout preventers must beshop serviced and shop tested to their working pressure and thetest data and the maintenance performed must be recorded andmade available to an official on request.
4.1.10 Special Sour Wells
Refer to Enform Publications Industry Recommended Practice
(IRP) #2:Completing and Servicing Critical Sour Wellsfordetailed information.
4.1.11 Slickline, Snubbing and Coil Tubing OperationsRefer to Enform IRP#13:Slickline OperationsRefer to Enform IRP#15:Snubbing OperationsRefer to Enform IRP#21:Coil Tubing Operations(Draft)
4.1.12 Hammer Unions
Hammer unions should not be used in the manifold shack orunder the rig substructure
http://www.enform.ca/media/3583/irp2_final_2007.pdfhttp://www.enform.ca/media/3583/irp2_final_2007.pdfhttp://www.enform.ca/media/3583/irp2_final_2007.pdfhttp://www.enform.ca/media/3604/irp13_final07_feb2009.pdfhttp://www.enform.ca/media/3604/irp13_final07_feb2009.pdfhttp://www.enform.ca/media/3604/irp13_final07_feb2009.pdfhttp://www.enform.ca/media/3607/irp15_final_2007.pdfhttp://www.enform.ca/media/3607/irp15_final_2007.pdfhttp://www.enform.ca/media/3607/irp15_final_2007.pdfhttp://ww2.enform.ca/cms-assets/documents/29152-464381.irp21final2010.pdfhttp://ww2.enform.ca/cms-assets/documents/29152-464381.irp21final2010.pdfhttp://ww2.enform.ca/cms-assets/documents/29152-464381.irp21final2010.pdfhttp://ww2.enform.ca/cms-assets/documents/29152-464381.irp21final2010.pdfhttp://www.enform.ca/media/3607/irp15_final_2007.pdfhttp://www.enform.ca/media/3604/irp13_final07_feb2009.pdfhttp://www.enform.ca/media/3583/irp2_final_2007.pdf -
7/29/2019 Completion Guide
29/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 26
4.1.13 Diagrams of Blowout Prevention Systems for WellServicing
Figure 4.A Equipment Symbols
-
7/29/2019 Completion Guide
30/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 27
Figure 4.B BOP Class A Pressure Rating and Component PlacementNotes: 1. Pressure rating of preventers is equal to or
greater than the production casing flange rating orthe formation pressure, whichever is the lesser.2. 50 mm lines throughout3. The positioning of the tubing and blind rams maybe interchanged.
4. Spool may have threaded side outlet (and valve) ifwellhead has threaded fittings.5. A flanged BOP port (and valve) below the lowestset of rams may replace spool (valve may bethreaded if wellhead has threaded fittings).
-
7/29/2019 Completion Guide
31/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 28
Figure 4.C BOP Class B Pressure Rating and Component PlacementNotes: 1. Pressure rating of preventers is equal to or greater
than the production casing flange rating or theformation pressure, whichever is the lesser.2. 50 mm lines throughout
3. The positioning of the tubing and blind rams may
be interchanged.4. Spool may have threaded side outlet (and valve) ifwellhead has threaded fittings.5. A flanged blowout preventer port (and valve)below the lowest set of rams may replace spool
(valve may be threaded if wellhead has threadedfittings.)
-
7/29/2019 Completion Guide
32/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 29
Figure 4.D BOP Class C Wellhead Configuration
-
7/29/2019 Completion Guide
33/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 30
Figure 4.E BOP Class C Optional Wellhead Configuration
-
7/29/2019 Completion Guide
34/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 31
4.2 Personnel
[Section 13, Drilling and Production Regulation]
The permit holder must ensure that there are a sufficientnumber of trained and competent individuals to carry out all well
operations safely and without causing pollution.
The following people must possess a valid Well Service BlowoutPrevention Certificate, issued byEnform: The driller on tour
The rig manager (tool push) and
The permit holders representative
If gas containing H2S is expected, every crew member must betrained in H2S safety.
Blowout prevention drills should be performed by each rig crewevery 7 days or once per well, whichever is more frequent.
Blowout prevention drills should be recorded in the servicing logbook.
Evidence of the qualifications of any person referred to in thissection must be made available to an official on request.
The rig crew must have an adequate understanding of, and beable to operate, the blowout prevention equipment and, whenrequested by an official and if it is safe to do so, the contractor
or rig crew must: Test the operation and effectiveness of the blowoutprevention equipment and
Perform a blowout prevention drill in accordance with theWell Control Procedure placard issued by the Canadian
Association of Oilwell Drilling Contractors or as outlined bythe Enform Blowout Prevention Manual
Refer to Enform IRP#7Standards for Wellsite Supervision ofDrilling, Completions and Workoversfor more information.
http://ww2.enform.ca/http://ww2.enform.ca/http://ww2.enform.ca/http://enform.ca/media/3589/irp7_final_2008.pdfhttp://enform.ca/media/3589/irp7_final_2008.pdfhttp://enform.ca/media/3589/irp7_final_2008.pdfhttp://enform.ca/media/3589/irp7_final_2008.pdfhttp://enform.ca/media/3589/irp7_final_2008.pdfhttp://enform.ca/media/3589/irp7_final_2008.pdfhttp://ww2.enform.ca/ -
7/29/2019 Completion Guide
35/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 32
4.3 Fire Precautions and Equipment Spacing
[Sections 45 and 47, Drilling and Production Regulation]
4.3.1 Engines
Permit holders must ensure that, if engines are located at awellsite, suitable safeguards are installed and tested to preventa fire or explosion in the event of a release of flammable liquidsor ignitable vapours.
For engines located within 25 metres of a well, petroleumstorage tank or other unprotected source of ignitable vapours,the Commission recommends that: The engine exhaust pipe is insulated or cooled to prevent
ignition in the event that flammable material contacts theexhaust pipe
The exhaust pipe is directed away from the well or sourceof ignitable vapours and
The exhaust manifold is sufficiently shielded to preventcontact with flammable materials
For diesel engines located within 25 metres of a well, theCommission recommends that one of the following devices beinstalled:
A positive air shutoff valve, equipped with a readilyaccessible control
A system for injecting inert gas into the engines cylinders,equipped with a readily accessible control or
A suitable duct so that air for the engine is obtained at least25 metres from the well
Permit holders must also ensure compliance with therequirements inSection 23.8 of the Occupational Health andSafety Regulation.
4.3.2 Fuel
Gasoline or liquid fuel, except for fuel in tanks that areconnected to operating equipment, must not be stored within 25metres of a well and drainage must be away from the wellhead.
4.3.3 SmokingSmoking is prohibited within 25 metres of a well.
http://www2.worksafebc.com/publications/OHSRegulation/Part23.asp#SectionNumber:23.8http://www2.worksafebc.com/publications/OHSRegulation/Part23.asp#SectionNumber:23.8http://www2.worksafebc.com/publications/OHSRegulation/Part23.asp#SectionNumber:23.8http://www2.worksafebc.com/publications/OHSRegulation/Part23.asp#SectionNumber:23.8http://www2.worksafebc.com/publications/OHSRegulation/Part23.asp#SectionNumber:23.8http://www2.worksafebc.com/publications/OHSRegulation/Part23.asp#SectionNumber:23.8 -
7/29/2019 Completion Guide
36/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 33
4.3.4 Recommended Spacing Distances
Permit holders must ensure that appropriate spacing ismaintained between potential sources of flammable liquids orignitable vapours and ignition sources. All fires must be
sufficiently safeguarded and all vessels and equipment fromwhich ignitable vapours may issue must be safely vented.
It is the responsibility of the permit holder to maintain sufficientequipment spacing.
WELLHEAD
FLAREORIN
CINERATOR
BOILER,STEAM
GENERATING
EQUIPME
NT,TEG*
PRODUCEDW
ATERTANK
OTHERSOURCESOFIGNITABLE
VAPO
URS
SEPAR
ATOR
FLAMETYPEEQUIPMENT
PRODUCEDFLAM
MABLELIQUIDS
CRUDEOIL&CON
DENSATETANKS
WELLHEAD 50 25 NS NS NS 25* 50
FLARE OR INCINERATOR 50 NS 25 25 25 25 50
BOILER, STEAM
GENERATING EQUIPMENT,
TEG*
25 NS 25 25 25 25 25
PRODUCED WATER TANK NS 25 25 NS NS 25* NS
OTHER SOURCES OF
IGNITABLE VAPOURSNS 25 25 NS NS 25* NS
SEPARATOR NS 25 25 NS NS 25* NS**
FLAME TYPE EQUIPMENT 25* 25 25 25* 25* 25* T 25*
PRODUCED FLAMMABLE
LIQUIDS CRUDE OIL &
CONDENSATE TANKS
50 50 25 NS NS NS** 25*
All distances are in metres (m).
* 25 m without flame arrestors, not specified with flame arrestors.
** Separator cannot be in the same dyke.
T Treaters should be at least 5 m (shell to shell) from other treaters.
Note:
a) Boilers etc. Includes steam generating equipment, electric generators and TEG units.
b) Other sources of ignitable vapours include compressors.
-
7/29/2019 Completion Guide
37/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 34
c) Flame type equipment includes: treaters, reboilers and line heaters.
d) All electrical installations must conform to the Canadian Electrical Code.
Table 4.1 Recommended Spacing Distances
Flares and incinerators must be located at least 80 metres fromany public road, utility, building, installation, works, place ofpublic concourse or reservation for national defence.
4.3.5 Flare Stacks
A sufficient area beneath and around flare stacks must becleared of flammable materials and vegetation.
The recommended blackened area beneath a flare stack is 1.5times the stack height.
The Commission recognizes that a lesser area may be justified
depending on the circumstances. It is the responsibility of thepermit holder to maintain a sufficient area, given the locationand the conditions under which flaring will or may occur.
4.3.6 Explosives
Explosives must be stored in properly constructed magazinesand be located a minimum of 150 metres from any wellservicing operation.
4.4 Incident Reporting
Spills and well control incidents must be reported to theProvincial Emergency Program (PEP) at 1-800-663-3456, andthe Commission at (250) 794-5200
Spills must be reported in accordance with theSpill ReportingRegulation.
4.5 Concurrent Operations
A concurrent operations plan is required for completionsoperations on any well that is located within 25 metres of
another well.Refer to Commission Information LetterOGC IL 08-20for moreinformation.
http://www.bclaws.ca/EPLibraries/bclaws_new/document/ID/freeside/46_263_90http://www.bclaws.ca/EPLibraries/bclaws_new/document/ID/freeside/46_263_90http://www.bclaws.ca/EPLibraries/bclaws_new/document/ID/freeside/46_263_90http://www.bcogc.ca/documents/informationletters/08-20%20Multi%20Well%20Pads%20Spacing%20IL.pdfhttp://www.bcogc.ca/documents/informationletters/08-20%20Multi%20Well%20Pads%20Spacing%20IL.pdfhttp://www.bcogc.ca/documents/informationletters/08-20%20Multi%20Well%20Pads%20Spacing%20IL.pdfhttp://www.bcogc.ca/documents/informationletters/08-20%20Multi%20Well%20Pads%20Spacing%20IL.pdfhttp://www.bclaws.ca/EPLibraries/bclaws_new/document/ID/freeside/46_263_90http://www.bclaws.ca/EPLibraries/bclaws_new/document/ID/freeside/46_263_90 -
7/29/2019 Completion Guide
38/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 35
5 Environmental ConsiderationsThe environmental considerations section outlines and explainsthe regulatory requirements for testing, repairing and reporting
environmental impacts: surface case venting flows, gasmigration, casing leaks and failures, noise, flaring and venting,fluid storage and spills.
5.1 Surface Casing Vent Flows
[Section 41, Drilling and Production Regulation]
5.1.1 DefinitionsSurface Casing Vent Flow (SCVF) means the flow of gas
and/or liquid from the surface casing/casing annulus.
Serious Surface Casing Vent Flow means
A vent flows with hydrogen sulphide (H2S) present
A vent flow with a stabilized gas flow rate equal to orgreater than 300 cubic metres per day (m3/d)
A vent flow with a surface casing vent stabilized shut-inpressure greater than
A hydrocarbon liquid (oil) vent flow
A vent flow due to wellhead seal failures or casing failure
A water vent flow if the water contains substances thatcould cause soil or groundwater contamination
A vent flow where any usable water zone in not covered bycemented casing or
Any other vent flow that constitutes a fire, public safety, orenvironmental hazard
5.1.2 Checking for Surface Casing Vent Flows
Testing for evidence of a surface casing vent flow must beconducted: During initial completion of the well
As routine maintenance throughout the life of the well
During the abandonment of the well
o one half the formation leak-off pressure at the surfacecasing shoe or
o 11 kPa/m times the surface casing setting depth
-
7/29/2019 Completion Guide
39/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 36
The Commission expects routine tests for surface casing ventflows to be conducted at the time of well suspension, during wellservicing operations (that is, recompletions) and annually for aperiod of five years if a positive surface casing vent flows hasbeen identified.
A 10-minute bubble test is adequate to test for the presence of asurface casing vent flow. The recommended procedure is asfollows:
Bubble Test Equipment:1) A container of water (from 500 ml to 1L)
2) Pipe fittings, small hose (minimum 6mm), or otherequipment necessary to direct gas flow from ventdownward in the water container
Bubble Test Procedure:1) Ensure that there are no gas leaks at fittings and welds;
2) Ensure there is no H2S present;
3) Ensure all valves in the vent line are open;
4) If necessary, connect test fittings to the vent so gas flowcan be directed into the container of water.
5) Immerse vent or hose a maximum of 2.5 cm below thewater surface;
6) Observe for 10 minutes. Note any gas flow (i.e. bubbles)which must be recorded as a positive vent flow;
7) Record observations.
5.1.3 Testing and Reporting Surface Casing Vent Flows
Serious surface casing vent flows present a safety orenvironmental hazard and must be reported to the Commissionas soon as possible.
The Commission recommends that permit holders reportsurface casing vent flows that are non-serious -those that do not
present an immediate safety or environmental hazard. This maybe accomplished by submitting via email [email protected] Casing FlowGas Migration Information Formor an industry report form . Testresults for non-serious surface casing vent flows must bemaintained on file and provided to the Commission on request.
A permit holder should perform annual surface casing vent flowtests on all non-serious surface casing vent flow for a minimum
mailto:[email protected]?subject=Surface%20Casing%20Vent%20Flow%20reportmailto:[email protected]?subject=Surface%20Casing%20Vent%20Flow%20reporthttp://www.bcogc.ca/documents/informationletters/08-20%20Multi%20Well%20Pads%20Spacing%20IL.pdfhttp://www.bcogc.ca/documents/informationletters/08-20%20Multi%20Well%20Pads%20Spacing%20IL.pdfhttp://www.bcogc.ca/documents/informationletters/08-20%20Multi%20Well%20Pads%20Spacing%20IL.pdfhttp://www.bcogc.ca/documents/informationletters/08-20%20Multi%20Well%20Pads%20Spacing%20IL.pdfhttp://www.bcogc.ca/documents/informationletters/08-20%20Multi%20Well%20Pads%20Spacing%20IL.pdfhttp://www.bcogc.ca/documents/informationletters/08-20%20Multi%20Well%20Pads%20Spacing%20IL.pdfhttp://www.bcogc.ca/documents/informationletters/08-20%20Multi%20Well%20Pads%20Spacing%20IL.pdfhttp://www.bcogc.ca/documents/informationletters/08-20%20Multi%20Well%20Pads%20Spacing%20IL.pdfmailto:[email protected]?subject=Surface%20Casing%20Vent%20Flow%20report -
7/29/2019 Completion Guide
40/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 37
of five years. The permit holder may select appropriate yearlytesting measures, however, the Commission may order specifictest measures for surface casing vent flows of particularconcern. If there is no change in the flow rate or shut inpressure after five years of testing, or if the vent dies out, no
further testing is expected. If a non-serious vent flow becomesserious, the permit holder must notify the Commission as soonas possible.
Recommended surface casing vent flow test procedures are asfollows:
5.1.3.1 Measuring Flowrate
Once a positive vent flow is detected, the flow rate andstabilized shut in pressures must be recorded. To measureventing gas volumes, a positive displacement gas meter, turbinemeter or an orifice well tester may be used. Equipment selectionshould be based on previous observations indicating what flowrate and pressure range can be expected. A positivedisplacement meter will be necessary to measure low volumesaccurately. An orifice well tester, with proper orifice plate, mayprovide satisfactory measurements if the 24 hour shut inpressure is 200 kPa or greater and builds quickly.
Install and use the equipment according to manufacturersinstructions and
1) Do not exceed the pressure/volume range of the
equipment2) Ensure that there are no leaks
5.1.3.2 Measuring Buildup Pressure
To determine the maximum shut-in surface casing pressure thefollowing method can be used.
Pressure Buildup Required Equipment: Pressure gauge or single pen static pressure recorder with
24 hour chart or
Dead weight pressure gauge or
Electronic pressure recorder
A pressure relief valve, calibrated to release the pressure if ithas built to its maximum allowable surface pressure, should beinstalled on the surface casing vent while measuring the buildup pressure. If it is anticipated that the maximum allowable shut
-
7/29/2019 Completion Guide
41/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 38
in pressure will be exceeded, a suitable recording device mustbe used in order to capture the rise and decline of pressure (i.e.electronic recorder).
Pressure Buildup Testing Procedure:1) Install pressure recorder and pressure relief valve.
2) Ensure that there are no gas leaks at fittings and welds.
3) If a chart is used, note the chart reading 24 hours later. Ifpressure has not stabilized, it may be necessary to changethe chart in order to cover a longer time period in order toachieve a maximum shut-in pressure.
4) Monitor the readings to determine when a stabilizedmaximum pressure is obtained and record this value.
5.1.4 Surface Casing Vent Flow Repairs5.1.4.1 Non Serious Repair
Remedial repair may be deferred until well abandonment fornon-serious surface casing vent flows.
In an effort to minimize the amount of venting from a non-serious surface casing vent flow, the permit holder may considerthe installation of a burst plate or pressure safety valve (PSV).The permit holder must obtain an exemption to section 18(8)(a)of the Drilling and Production Regulation to allow the installationof a burst plate or pressure safety valve.
Non-serious surface casing vent flows must be repaired at thetime of well abandonment.
5.1.4.2 Serious Repair
The permit holder of a well determined to have a serioussurface casing vent flow should contact the Commission assoon as possible to discuss repair or managementrequirements.
5.1.4.3 Surface Casing Vent Flow Production
If the permit holder wishes to explore the option of producing thesurface casing vent flow, an application must be made to theDrilling and Production Department to obtain an exemption tosection 18(8)(a) of the Drilling and Production Regulation.Requests will be considered if: The source depth and formation of origin has been clearly
identified
-
7/29/2019 Completion Guide
42/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 39
The permit holder owns the mineral rights to produce thesource formation
The cemented portion of the surface casing or the nextcasing string covers the deepest known usablegroundwater and
The flow has been analyzed and determined to be sweet (0percent H2S)
The Commission may rescind the approval to produce from thesurface casing vent and may require the surface casing ventflow to be repaired at any time if the Commission determines asafety or environmental hazard exists.
5.2 Gas Migration
[Section 41, Drilling and Production Regulation]
5.2.1 Definitions
Gas Migration (GM) means a flow of gas that is detectable atthe surface outside of the outermost casing string (often referredto as external migration or seepage).
Serious Gas Migration means gas migration that1) Contains hydrogen sulphide
2) Creates a fire or public safety hazard or
3) May cause off-lease environmental damage (such as,
groundwater contamination).A permit holder must report, via email [email protected], all occurrences of gasmigration to the Commission as soon as possible.
The permit holder is not required to test for gas migration unlessthere is visible evidence that it is occurring. Upon initialdiscovery of gas migration, a gas sample should be collected toidentify the source of the gas. Recommended gas migrationtesting procedures are as follows:
5.2.1.1 Gas Migration Testing
Once gas migration is visible, the Commission requires thattesting be carried out to identify the source of the gas. Testingmust be done in frost free months only and periods immediatelyafter a rainfall must be avoided. If less than full scale readingsare obtained, the soil horizon must be examined to ensure thatreadings are not the result of contaminated solids due to spills
mailto:[email protected]?subject=Gas%20Migration%20occurencemailto:[email protected]?subject=Gas%20Migration%20occurencemailto:[email protected]?subject=Gas%20Migration%20occurence -
7/29/2019 Completion Guide
43/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 40
of diesel fuel, solvents, oil, etc. If contaminated soils aresuspected, the soil must be excavated and removed. Retestingis then required. Instrumentation must be calibrated regularlyand checked daily when in use.
Select sample testing points as follows:
Two within 30 cm of wellbore on opposite sides At two metre intervals outward from the wellbore every 90
(a cross with the wellbore at centre) to a distance of sixmetres and
At any points within 75 metres of the wellbore where thereis apparent vegetation stress
Required Equipment: Bar or auger (64 mm or less in diameter) capable of
penetrating a minimum of 50 cm
Calibrated monitor or other instrument capable of detectinghydrocarbon at one percent lower explosive limit (LEL)
Equipment or material to seal the hole at surface while soilgases are being evacuated from the soil through theinstrument
Test Procedure:1) Perform instrument check (for example,calibration, voltage,
zero)
2) Insert auger or make a bar hole a minimum of 50 cm deep
3) Isolate the hole from atmospheric contaminations
4) Insert hose, wand, or other equipment a minimum of 30 cminto hole, maintaining a seal at surface to preventatmospheric gas and soil gas mixing
5) Withdraw soil gas sample. The volume, rate, etc., willdepend on the instrumentation being used. Ensure that asufficient sample is removed to purge lines andinstrumentation
6) Record observations
7) Purge instrument and lines
-
7/29/2019 Completion Guide
44/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 41
5.3 Casing Leaks and Failures
[Section 18, Drilling and Production Regulation]
A permit holder must notify the Commission of any casing leakor casing failure as soon as possible. The leak or failure mustbe repaired within a reasonable time frame, giving considerationto the accessibility of the site and the seriousness of the leak orfailure.
5.4 Noise
[Section 40, Drilling and Production Regulation]
A permit holder must ensure that well operations do not cause
excessive noise. Permit holders should work with area residentsto minimize noise impacts when undertaking completionsactivities near populated areas.
The B.C. Noise Control Guideline(OGC IL 09-09) containsinformation regarding acceptable noise levels and noiseassessment techniques.
5.5 Flaring and Venting
Refer to theFlaring and Venting Reduction Guideline fordetailed guidance.
5.6 Fluid Storage
[Section 50, Drilling and Production Regulation]
Secondary containment of tanks associated with completionsoperations is generally not required. For extended, unmannedflowback operations that require a facility permit, secondarycontainment in accordance with the National Fire Protection
Agencys Flammable and Combustible Liquids Code (NFPA 30)is required.
Fracturing fluid returns must be stored in accordance with theCommissions Information Letter on the storage of fluid returnsfrom hydraulic fracturing operations(OGC IL 09-07).
http://www.bcogc.ca/documents/BC%20Noise%20Control%20Best%20Management%20Practices%20Guideline%20March%202009.pdfhttp://www.bcogc.ca/documents/BC%20Noise%20Control%20Best%20Management%20Practices%20Guideline%20March%202009.pdfhttp://www.bcogc.ca/document.aspx?documentID=963&type=.pdfhttp://www.bcogc.ca/document.aspx?documentID=963&type=.pdfhttp://www.bcogc.ca/document.aspx?documentID=963&type=.pdfhttp://www.bcogc.ca/documents/informationletters/OGC%2009-07%20Storage%20of%20Fraccing%20Fluid%20Returns.pdfhttp://www.bcogc.ca/documents/informationletters/OGC%2009-07%20Storage%20of%20Fraccing%20Fluid%20Returns.pdfhttp://www.bcogc.ca/documents/informationletters/OGC%2009-07%20Storage%20of%20Fraccing%20Fluid%20Returns.pdfhttp://www.bcogc.ca/documents/informationletters/OGC%2009-07%20Storage%20of%20Fraccing%20Fluid%20Returns.pdfhttp://www.bcogc.ca/document.aspx?documentID=963&type=.pdfhttp://www.bcogc.ca/documents/BC%20Noise%20Control%20Best%20Management%20Practices%20Guideline%20March%202009.pdf -
7/29/2019 Completion Guide
45/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 42
6 Data SubmissionThis section describes the regulatory requirements for reportingon the completion, workover and abandonment of wells, as well
as regulatory requirements for reporting on well deliverabilitytests and hydraulic fracturing fluid.
All data referred to in this section, with the exception ofhydraulic fracturing fluid reports, must be submitted to theCommissions Victoria office:
Well Data ManagementBC Oil and Gas Commission300-398 Harbour RoadVictoria, B.C. V9A 0B7
Hydraulic fracturing fluid reports are only accepted electronicallyand can be uploaded toKERMIT.
6.1 Completion/Workover/Abandonment Reports
[Sections 26 and 36, Drilling and Production Regulation]
A signed copy of theCompletion/Workover Reportand requiredattachments must be submitted to the Commission office inVictoria within 30 days of completing the operation. Incompletereports will not be accepted and will be returned to sender.
If a well has been abandoned, a summary of the surfaceabandonment must be included for the well status to bechanged to abandoned and the location to be a candidate for aCertificate of Restoration.
Appendix Aspecifies which operations require aCompletion/Workover Report and which operations do not.Refer toInformation Bulletin 2011-05for more information.
6.1.1 Instructions for Completion of the Report
Statements such as see attached daily reports are
unacceptable and deemed incomplete. Incomplete reports willnot be accepted and will be returned.
https://kermit.bcogc.ca/Login.aspxhttps://kermit.bcogc.ca/Login.aspxhttps://kermit.bcogc.ca/Login.aspxhttp://www.bcogc.ca/document.aspx?documentID=668&type=.pdfhttp://www.bcogc.ca/document.aspx?documentID=668&type=.pdfhttp://www.bcogc.ca/document.aspx?documentID=668&type=.pdfhttp://www.bcogc.ca/document.aspx?documentID=1066&type=.pdfhttp://www.bcogc.ca/document.aspx?documentID=1066&type=.pdfhttp://www.bcogc.ca/document.aspx?documentID=1066&type=.pdfhttp://www.bcogc.ca/document.aspx?documentID=1066&type=.pdfhttp://www.bcogc.ca/document.aspx?documentID=668&type=.pdfhttps://kermit.bcogc.ca/Login.aspx -
7/29/2019 Completion Guide
46/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 43
6.1.1.1 Reason for work
State the purpose of the operation (For example, initialcompletion; to increase productivity; to shut-off water flow, etc.)
6.1.1.2 Chronological summary of work done
Including date, state the highlights of the operation such asperforation intervals, zone(s), stimulation operations, final flowrates, pressure tests, fluid recovery, plugs, type of completionstring installed.
6.1.1.3 Example Summary:
2006/11/10 Perf Bluesky 971.2973.4 mKB
2006/11/13 Frac: Pump 1.5 m
3
15% HCL acid.Pump 10 m3 Fracsol, 10 tonnes of 20/40 mesh sand.Formation breakdown @ 21,000 kPa.
2006/11/16 Flowed gas 3.720 103m3/d @ 2200 kPa.
Water production 2.1 m3/hr.
2006/11/21 Bluesky uneconomic.
Abandoned perfs w/bridge plug at 969 mKB w/ 8 lineal mcement on top.
Pressure tested BP.
2006/11/28 Cut off casing 1 m below ground, welded ventedplate on casing. Wellsite requires surface restoration.
A Downhole Schematic Diagram and a copy of the DetailedDaily Report of the completion, workover or abandonmentoperations must be attached to each copy of theCompletion/Workover Report. In cases where a service rig isnot used, a copy of the service companys report to the operatormay be submitted instead of the detailed daily reports.
6.1.1.4 Completion TypeIndicate what kind of completion was done (for example,completion of two zones [dual], multiple zones perforated [threeor more], openhole well).
-
7/29/2019 Completion Guide
47/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 44
6.1.1.5 Completion Activity
Indicate the main purpose or type of the completion or workover(for example, openhole, perforate, fracture, acidize, cementsqueeze or remedial).
6.1.1.6 Stimulation Type
State which stimulation type achieved breakdown or well flow.
6.1.1.7 Stimulation Volume
State the total fluids pumped in the stimulation in cubic metres(m3).
6.1.1.8 Stimulation Pressure
State the maximum pressure used in the stimulation inkilopascals (kPa).
6.1.1.9 Flow Summary
If applicable, indicate the hydrogen sulphide percent, oil rate,water rate, choke size or API gravity.
6.1.1.10 Flow RateState the final gas flow rate in 103m3/day.
6.1.1.11 Flow Pressure
State the final flow pressure in kPa.
6.1.1.12 Flow Date
State the final flow date.
6.1.1.13 Radioactive material
Indicate whether radioactive material was used in the workover(such as frac sand). If so, attach documentation explaining themethod of disposal or, if buried on site, attach sketch of locationshowing burial location and indicate depth of burial and volumeof material.
-
7/29/2019 Completion Guide
48/77
Well Completion, Maintenance and Abandonment Guideline, Version 1.9
BC Oil & Gas Commission 45
6.1.1.14 Result of work done
State the outcome of the operation (for example, well onproduction, productivity increased from 24 m3 per day to 31 m3per day, water flow successfully shut-off) For the aboveexample, the result would be well abandoned.
6.2 Well Deliverability Test Reports
[Section 63, Drilling and Production Regulation]
6.2.1 Well Deliverability Test Report Instructions
6.2.1.1 Report Filing
A report is required for all: Deliverability type flow tests
Clean-up flows
Under-balanced drilling operations that result in burnablegas to surface.
Reports are due within 60 days of the completion of thetest.
Absolute open flow (AOF) tests are required for all:
Wells producing form pools with suspected water drive
Wells that are classified as exploratory wildcat orexploratory outpost
6.2.1.2 Test Type
Indicate the appropriate test type by selecting the correspondingcheck box. Where the sole purpose of the test is a well clean-up, select CU as the test type and enter the applicable rateand volume data. However, if a clean-up period is carried out inconjunction with a subsequent deliverability test, select the testtype corresponding to the deliverability test and include theclean-up flow rate and production volumes on the same formwith the AOF data.
6.2.1.3 Under-Balanced Drilling
This form is to be submitted for under-balanced drilling (UBD)operations that result in burnable gas to surface. Reported testtype should be UBD. Flared gas volumes reported are to bethe net volume produced by the target formation (gas produced
-
7/29/2019 Completion Guide
49/77
Well