condensed catalog - assa abloy master... · condensed catalog a selection of ... (see full line...

Condensed CatalogA Selection of Featured PEMKO Products

www.pemko.comCopyright © 2012, Pemko Manufacturing Co., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Pemko Manufacturing Co. is prohibited. 5

Commercial Thresholds

•Unless exact net cut is specified, thresholds less than 48" are supplied 1⁄2" over length, and thresholds 48" and over are supplied 1" over length to allow for fitting.

•Unless otherwise specified, all thresholds are pre-drilled on the center line and are supplied with fasteners.•Extruded bronze (brass) thresholds are supplied with solid brass screws.•For corrosive environments, stainless steel screws are available at an extra cost.•Available with PemKote™ non-skid coating. Please specify PemKote™ when ordering. Please furnish drilling instructions when

ordering with PemKote™ as it is difficult to drill through.

Saddle Thresholds

AVAILABLE FINISHES FOR PRODUCTS SHOWN ON THIS PAGE (see FULL LINE CATALOG or WEBSITE for finish chart)

A (Mill Finish Aluminum) • AK (Mill Finish Aluminum w/PemKote™ Non-Slip Coating) • B (Mill Finish Extruded Bronze [Brass]) BDG (Bright Dip Gold Anodized)•D (Dark Bronze Anodized)•G (Gold Anodized) • SN (Satin Nickel Anodized) NOTE: BDG, G, SN are available with limited inventory

171_ AVAILABLE FINISHES:A, B, BDG, D, G, SN

172_ AVAILABLE FINISHES:A, B, D, G, SN

176_ AVAILABLE FINISHES:A, B, D, G

270_ AVAILABLE FINISHES:A, B, D, G



2548_ AVAILABLE FINISHES:A, D, G



6 www.pemko.comCopyright © 2012, Pemko Manufacturing Co., an ASSA ABLOY Group company. All rights reserved.

Reproduction in whole or in part without the express written permission of Pemko Manufacturing Co. is prohibited.

Stainless Steel Saddle Thresholds


A (Mill Finish Aluminum) • AK (Mill Finish Aluminum w/PemKote™ Non-Slip Coating) • D (Dark Bronze Anodized)•SS (Stainless Steel)

154SS_ AVAILABLE FINISHES:SS (#4 Finish)

Heavy D uty Thresholds•Ideal for heavy-duty, high-traffic and high weight-bearing applications, such as industrial facilities, schools, cafeterias, manufacturing

buildings and hospitals•Withstands coastal and high-humidity conditions•Ultra-durable, extra thick extruded nickel-aluminum construction is guaranteed for ten (10) years

2715_ AVAILABLE FINISHES:A, AK, D

1715_ AVAILABLE FINISHES:A, AK, D

Modular Heavy Duty ThresholdsModular construction without the expense of custom cast thresholds. There is no restriction on width additions (in 1" increments)

1716_ AVAILABLE FINISHES:A, AK, DAllow 5⁄8" door clearance.

1717_ AVAILABLE FINISHES:A, AK, DAllow 5⁄8" door clearance.

253SSFG AVAILABLE FINISHES:SS (#4 Finish)

175SS AVAILABLE FINISHES:SS (#4 Finish)

12(12.7)

1163(77.8)

(127.0)5

12(12.7)

252x3SSFG AVAILABLE FINISHES:SS (#4 Finish)

Commercial Thresholds (C ont.)

Available in 36", 48", 72", and 98" lengths only.

(127.0)5

1 4(6.4)

(127.0)5

1 4(6.4)

7www.pemko.comCopyright © 2012, Pemko Manufacturing Co., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Pemko Manufacturing Co. is prohibited.

Thermal Barrier SaddlesBlack rigid polypropylene key between extrusions provides a thermal barrier (designated by “FG” Frost Guard following finish code)

273x3_FG AVAILABLE FINISHES:A, B, D, G








A(MillFinishAluminum)•B (Mill Finish Extruded Bronze [Brass])•D(DarkBronzeAnodized)•G (Gold Anodized) NOTE: G is available with limited inventory

Commercial Thresholds (C ont.)


Door Bottoms

4131_RL AVAILABLE FINISHES:BDG, C, D, SN

Automatic Door Bottoms

4131_NBL AVAILABLE FINISHES:BDG, C, D, SN

4301_RL AVAILABLE FINISHES:C, D

25 32(46.0)

1

2932

(23.8)

SEMI-MORTISED

SURFACEMOUNTED

4301_NBL AVAILABLE FINISHES:C, D,

434_NBL AVAILABLE FINISHES:A

434_RL AVAILABLE FINISHES:A

4301_PKL AVAILABLE FINISHES:C, D

ALTERNATE INSERT FOR 4301

4131_PKL AVAILABLE FINISHES:BDG, C, D, SN

ALTERNATE INSERTS FOR 4131

4131_SL AVAILABLE FINISHES:BDG, C, D, SN

434_PKL AVAILABLE FINISH:A

ALTERNATE INSERT FOR 43429

32(23.8)

25 32(46.0)

1

SEMI-MORTISED

SURFACEMOUNTED

78

(22.2)

1132(34.1)

1

78

(22.2)

1132(34.1)

1


A(MillFinishAluminum)•BDG(BrightDipGoldAnodized)•C(ClearAnodized)•D(DarkBronzeAnodized)•SN (Satin Nickel Anodized)

Special finishes available upon request.

SEMI-MORTISED

SURFACEMOUNTED

27 32(46.8)

1

1932

(15.1)

SEMI-MORTISED

SURFACEMOUNTED

27 32(46.8)

1

1932

(15.1)

Sponge EPDM (R)Sponge EPDM (R) nylon brush (NB)

nylon brush (NB)Sponge EPDM (R)

nylon brush (NB)



411_RL AVAILABLE FINISHES:A

Automatic Door Bottoms

411_NBL AVAILABLE FINISHES:A

420_PKL AVAILABLE FINISHES:AFor hollow metal doors. Maximum drop is 1/2".

411_PKL


411_SL 420_VL


420_SL

Door Bottoms (Cont.)

Sponge EPDM (R)nylon brush (NB)

Acoustic Automatic Door Bottoms: PDB Series

916(14.3)

38(34.9)

178

(47.6)

1

916(14.3)

SEMI-MORTISED

SURFACEMOUNTED

PDB411_E AVAILABLE FINISHES:AAVAILABLE LENGTHS: 26" to 48"

PDB4131_E AVAILABLE FINISHES:C, DAVAILABLE LENGTHS: 26" to 48"

Full-Mortise Application Surface Mounted or Semi-Mortised Application

• Uniquedesigncreatesuniformsealpressureacrosstheentiredoorbottomresultinginsuperioracousticperformance

• PDBSerieshas“sealed-in-place”typeperformance,achievingzerodropinSTCratingsinmanytypi-cal wood and hollow metal door applications.

• PatentPending

• Adjustmentis1/8"to1/2".Maximumdimensionfrombottomofdoortosealingsurfaceis1/2"

EPDM (E)

EPDM (E)

NEW!



Door Shoes• NowavailablewithPemkoPrene™ (PK) thermo-plastic elastomer, an excellent cold weather seal which stays flexible between

-70°F and +250°F

• Alsoavailablewithvinyl(V);bothsealsarethesameshapeandsize

• Slottedholesforeasyadjustment.Providedwithstainlesssteelfasteners

• Raindripmodelisidealfordeflectingrainawayfromthebottomofdoor

13 16(46.0)

1

516(33.3)

118

(28.6)

1

34

(19.1)

11 16(17.5)

116(27.0)

1

34(44.5)

1

1516

(23.8)

11 16(17.5)

316(30.2)

1

11 16(17.5)


A(MillFinishAluminum)•BDG(BrightDipGoldAnodized)•D(DarkBronzeAnodized)•G(GoldAnodized)•PW (Painted White) SN (Satin Nickel Anodized)

211_V211_PK AVAILABLE FINISHES:A, D, G

215_V215_PK AVAILABLE FINISHES:A, BDG, D, G, PW, SN

216HM_V216HM_PK AVAILABLE FINISHES:A, D, G


For hollow metal doors with inverted bottom channel.

217HM_V217HM_PK AVAILABLE FINISHES:A, D, G

1316(46.0)

1

For hollow metal doors

For hollow metal doors

2173_V AVAILABLE FINISHES:A, BDG, D, G, PW

2343_V AVAILABLE FINISHES:A, D, G

2230_NB AVAILABLE FINISHES:A, D, G

2211_V2211_PK AVAILABLE FINISHES:A, D, GCombination doorshoe and kick platewith rain drip.

209_V AVAILABLE FINISHES:A, D, G


2170_VAVAILABLE COLORS: D, WAVAILABLE LENGTHS: 36", 48" All Vinyl

Also available with unnotched insert:2170_V36UN2170_V48UN



3692_PK773AVAILABLE FINISHES: AAVAILABLE LENGTHS: 36", 48"



Astragals and Meeting Stiles

Split Astragals and Meeting Stile Gasketing• AstragalsandmeetingstileswithafirelabelmaybemountedonpairsofdoorswhereinthegapmeetstherequirementsofNFPA

80, “The clearance between the meeting edges of doors swinging in pairs on the pull side shall be 1⁄8" ± 1⁄16" (3.18mm ± 1.59mm) for steel doors and shall not exceed 1⁄8" (3.18mm) for wood doors.”

•When used as split astragals on double doors, two lengths must be ordered: one for each door

•Punchedwithslottedholesforadjustment

• Allclearanodizedbrushproductsaresuppliedwithgraybrush(availablewithblackbrushuponrequest)


Door Bottom Sweeps

315_N AVAILABLE FINISHES:B, BGD, C, D, G, PW, SN

321_N AVAILABLE FINISHES:C, D, G

345_V345_PK AVAILABLE FINISHES:A, BDG, D, G, PW

3452_NB AVAILABLE FINISHES:BDG, C, D, G, PW, SN

345_NB AVAILABLE FINISHES:A, BDG, D, G, PW

A(MillFinishAluminum)•B(MillFinishExtrudedBronze[Brass])•BDG(BrightDipGoldAnodized)•C (Clear Anodized)

D(DarkBronzeAnodized)•G(GoldAnodized)•PW(PaintedWhite)•SN (Satin Nickel Anodized)

297_S AVAILABLE FINISHES:A, BDG, D, G, PW, SN

303_PK 297_PK 303_V 297_V

303_S AVAILABLE FINISHES:A, BDG, C, D, G, PW, SN

29310_S AVAILABLE FINISHES:C, D, G

A(MillFinishAluminum)•BDG(BrightDipGoldAnodized)•C (Clear Anodized) D(DarkBronzeAnodized)•G (Gold Anodized) PW(PaintedWhite)•SN (Satin Nickel Anodized)

ALTERNATE INSERTS

29310_PK 29310_P

29310_V

ALTERNATE INSERTSALTERNATE INSERTS

3151_NAVAILABLE FINISH: C, D, G

1(31.8)

1(25.4)


Astragals and Meeting Stiles (Cont.)

305_N AVAILABLE FINISHES:B, C, D, G

18041_NB AVAILABLE FINISHES:C, D, G, SN

313_N AVAILABLE FINISHES:A, D, G

PEMKO offers a broad line of nylon brush weatherstripping including the 18062_NB and 18100_NB, which are suitable for split astragal applications.

Adjustable Astragals•When used as split astragals on double doors, two lengths must be ordered: one for each door•Available in 84", 96" and 120" lengths•351 is surface applied NOTE: If you require split astragals in a metal-to-gasket configuration, you must order each leaf separately with your choice of insert.

351_/351_S AVAILABLE FINISHES:B, C, D, G 351_PK351_P 351_V

Overlapping Astragals

355_S AVAILABLE FINISHES:B, BDG, C, D, G, PW, SN

355_V

355_P

If specifications state that an astragal is required to satisfy a fire and / or smoke rated opening, then a

thru-bolted 357SP or SS in conjunction with S88 seal is the only configuration that can be used.

356_V AVAILABLE FINISHES:A, BDG, D, PW, SN

357_ with S88_ AVAILABLE FINISHES:SP, SS


A(MillFinishAluminum)•B(MillFinishExtrudedBronze[Brass])•BDG(BrightDipGoldAnodized)•C (Clear Anodized)

D(DarkBronzeAnodized)•G(GoldAnodized)•PW(PaintedWhite)•SN(SatinNickelAnodized)•SP(GalvannealedSteel)•SS (Stainless Steel)

ALTERNATE INSERTS

ALTERNATEINSERTS



Adhesive Gasketing

SiliconSeal™ - Adhesive Backed Fire/Smoke GasketingS44 is designed for tighter frames and demonstrates extremely low closing force

S44_ AVAILABLE FINISHES:BL, D, GR, WAVAILABLE LENGTHS:17', 18', 20', 21', 25', 30', 510'

S77_ AVAILABLE FINISHES:BL, C, D, WAVAILABLE LENGTHS:17', 18', 20', 21', 25'

S88_ AVAILABLE FINISHES:BL, C, D, GR, TAN, WAVAILABLE LENGTHS:17', 18', 20', 21', 25', 30', 204', 510'

S773_ AVAILABLE FINISHES:BL, D, GR, WAVAILABLE LENGTHS: 17', 18', 20', 21', 25', 30', 250'


BL(Black)•C(Clear)•D(DarkBrown)•GR(Gray/LightGray)•TAN(Tan)•W (White)

• Extruded from high-temperature silicone with MicroShield®, a silver-based antimicrobial additive

• Effective between -58ºF and 450ºF

•Adhesive Backed

• Self-extinguishing and non-toxic

• Unaffected by sunlight, ozone and ultraviolet rays

• Exceeds the requirements for Antimicrobial Test JIS-Z-2801

MicroShield® Antimicrobial Gasketing:

AM88_AVAILABLE FINISHES: BL, C, D, WAVAILABLE LENGTHS: 17', 18', 20', 21', 25', 30', 510'

AM44_AVAILABLE FINISHES: BL, C, D, W AVAILABLE LENGTHS: 17', 18', 20', 21', 25', 30', 510'

MicroShield®

As part of their promise to provide innovative solutions to their customers, certain ASSA ABLOY Group brands offer the MicroShield® technology, a silver-based antimicrobial additive designed to inhibit the growth of bacteria.

MicroShield® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company.

NEW!

S771x6_AVAILABLE FINISHES: BL, CAVAILABLE LENGTHS: 7, 8, 10, 17, 18, 20, 21, 25

5 16(7.9)

(25.4)1

NEW!

•Designed for hollow metal and wood meeting stile applications

• Seal begins compressing at 5⁄16"; compresses to seal up to a 1⁄16" gap

S776_AVAILABLE FINISHES: BLAVAILABLE LENGTHS: 17', 18', 20', 21'•Designedforhollowmetalandwoodmeetingstile

applications•Sealbeginscompressingat3 ⁄8"; compresses to seal up

to a 1⁄16" gap

NEW!


PemkoPrene™ - Adhesive Backed Fire/Smoke GasketingPK33_ AVAILABLE FINISHES:BL, D, WAVAILABLE LENGTHS:17', 18', 20', 21', 25', 30', 510'

PK55_ AVAILABLE FINISHES:BL, D, WAVAILABLE LENGTHS:17', 18', 20', 21', 25', 30', 510'

Hot Smoke Seal™/SiliconSeal Combination Fire/Smoke Gasketing

Adhesive Gasketing (Cont.)

HSS2000xS44__ AVAILABLE FINISHES:BL, D, WAVAILABLE LENGTHS:18’, 20’, 21’, 24’

HSS2000xS88_ AVAILABLE FINISHES:BL, C, D, GR, TAN, WAVAILABLE LENGTHS:18’, 20’, 21’, 24’, 30'

Specialized Products

Adhesive Astragal/Meeting Stile SealsS771_ AVAILABLE FINISHES:BL, C, D, GR, WAVAILABLE LENGTHS:7', 8', 9', 10'

S772_ AVAILABLE FINISHES:BL, D, WAVAILABLE LENGTHS:7', 8', 10'

Privacy Door Latch•Easy to install, simple to operate •ADA compliant•Enhanced room privacy•UL classified as a fire door accessory

PDL_ AVAILABLE FINISHES:3 (Polished Brass), 4 (Satin Brass), 10B (Dark Bronze),26 (Polished Chrome), 26D/15 (Satin Chrome/Nickel)

87°

58

(41.3)

”1

12

(38.1)

”1

316

(55.6)

”2

HSS1000_ is a non-adhesive backed (mortise applied) intumescent


Gasketing: BL(Black)•C(Clear)•D(DarkBrown)•GR(Gray/LightGray)•W (White) Thresholds: BL (Black Vinyl)

PemkoPrene™ Hot Smoke Seal Edge Sealing for Category B Doors

HSS1000_ AVAILABLE FINISHES:Graphite (no code), WAVAILABLE LENGTHS:7', 8', 10', 18', 21', 24'

HSS2000_ AVAILABLE FINISHES:Graphite (no code), WAVAILABLE LENGTHS:7', 8', 10', 18', 21', 24'

Privacy Door Latch Bracket•For use on Dunbartan, Reddiframe, and Timely Frames•Powder Coated

PDLBRKT_ AVAILABLE COLORS: OW (Off White), DB (Dark Brown)

condensed catalog - assa abloy master... · condensed catalog a selection of ... (see full line...

Documents