consolidators t s - s3-ap-southeast-2. · pdf fileresealing should be done every 2-3 years and...

placing furniture back can be easily painted over with some more sealer. Cleaning and maintenance should be done with REFRESH and a re seal should be carried out every 2 years – more frequently for high traffic areas. Harsh cleaners such as Jif, Handy Andy or any acids should not be used on the sealed surface. Coverage: Allow approx. 5 square metres per litre for a finished job with 2 coats.Cleanup: Environex CYCLONE is to be used to clean up applicators. If you can dedicate an applicator for this job only, allow it to go hard and place in sealer 30 minutes before starting next time. The sealer will soften the brush or applicator.

ENDURE is a solvent based sealer designedto give a gloss finish to slate, sandstone,pavers, concrete and most masonry (notsuitable for honed masonry). A hard wearingsurface sealer, ENDURE will darken andhighlight the colours of the surface while offering protection from normal householdspills. A small test area is recommended.

DIRECTIONS FOR USE: Ensure area to besealed is clean and dry. Allow a minimum of14 days drying time after laying new pavers.Do not apply to wet surfaces or surfaces thatare below 10° Celsius or over 30° Celsius.A lambswool applicator will give best results.DO NOT USE A ROLLER. Product should beapplied in thin coats with no pooling. At least2 coats of sealer are recommended fornormal domestic use, allow from 1-4 hoursbetween coats (depending on atmosphericconditions) and 24 hours before heavytraffic. If in doubt seek advice from yourEnvironex Stonecare Specialist.

COVERAGE: For a finished job with 2 coatsallow 5 square metres per litre. This coveragemay be reduced on more porous surfaces.

CLEANUP: Clean any affected areas andequipment using Environex CYCLONE.

mAINTENANCE: All masonry sealed with ENDURE should be routinely cleaned usingEnvironex REFRESH as a routine cleaner orMAESTRO if there is a moss or mould buildup.RECOATING: ENDURE has a high lifeexpectancy (2-3 years) dependent uponapplication, traffic conditions and levelof maintenance. ENDURE should be theonly sealer used in future for re-sealing – this will avoid any compatibility issues.If sealing over a surface that has previously been sealed, test a small area first. For best results always check with yourEnvironex Technical Representative.FOR FURThER TEChNICAL ASSISTANCECALL 1800 999 196 EmERGENCY INFORmATION: SPILLS: Eliminate ignition sources. Absorb ontoearth, vermiculite or other absorbentmaterial. Transfer into clean labelled drums for disposal. S29 Do not empty into drains.FIRE: S43 In case of fire, use sand, earth, chemical powder or foam. Water spray may be used to cool containers. Additionalinformation is listed in the Material Safety Data Sheet. In an emergency Dial 000 Police or Fire Brigade.

Xn Harmful. N Dangerous for the Environment. R10 Flammable. R20/21 Harmful by inhalation and incontact with the skin. R37/38 Irritating to respiratory system and skin. R65 Harmful: May cause lungdamage if swallowed. R51 Toxic to aquatic organisms. R53 May cause long-term adverse effects in theaquatic environment.SAFETY DIRECTIONS: When spraying solutions, we recommend a respirator mask be worn by thespray operator and anyone assisting in the spray operations. Use only when there is adequate ventilationavailable. Avoid contact with skin and eyes and avoid breathing vapour or spray mist. S16 Keep awayfrom sources of ignition.FIRST AID: For advice, contact a Poisons Information Centre (Phone Australia 131 126) or a doctor(at once). If swallowed, do NOT induce vomiting. If in eyes, wash out immediately with water. If skin orhair contact occurs, remove contaminated clothing and flush skin and hair with running water. If inhaled,remove from contaminated area. Apply artificial respiration if not breathing.

Batch No:CONTAINS 700 mL/L XYLENE, 167 g/L LIqUID HYDROCARBONS

UN 1866, CLASS 3, RESIN SOLUTION FLAMMABLE, HAZCHEM 3[Y]E, PG III

NET CONTENTS

1L 4L 10L 20L 200L

POISONKEEP OUT OF REACH OF CHILDREN.

READ SAFETY DIRECTIONS BEFORE OPENING OR USING.

Manufactured byEnvironex International

19 Motivation Drive,Wangara, WA 6065

Ph: (08) 9302 [email protected] IN AUSTRALIA

PROUDLY MADE

Quality ISO 9001

ENDUREENDUREPROTECTS MASONRY AGAINST

SOILING AND STAINING

HI-LITE is a blend of solvent based sealersdesigned to darken the surface of sandstone,pavers, limestone, pebbles and concrete. It willhighlight the colours of the surface withoutleaving the usual gloss level that can result inslippery surfaces. HI-LITE is ideal for concretepavers and sandstone where a darker look isdesired. On dense stone, a higher gloss levelmay result – always test first. HI-LITE willprovide protection from normal householdspillages. For a full gloss look use EnvironexENDURE.APPLICATION: Should be done when thesurface is clean and dry. A lambswoolapplicator or spray applicator will give bestresults. DO NOT USE A ROLLER. Productshould be applied evenly across the surface ensuring no pools or puddles are left. Twocoats are recommended with around2-4 hours between coats depending onambient conditions. Curing after final coat is overnight. If foaming occurs more sealershould be applied and foaming removed. It is normal for the first coat to leave a patchyresult. The second coat will resolve this.COVERAGE: Allow 5 square metres per litre for a finished job. This can reduce on moreporous surfaces.DRYING TIME: Allow 12 hours after final coat before walking or using the surface.

CLEANUP: Cleanup applicators or sprayingequipment using Environex CYCLONE. Applicators can be left to go hard – place them back in the sealer and they will soften in about 10 minutes.RECOATING: HI-LITE will last for 3-5 yearsdepending on traffic. It is strongly advised thatHI-LITE is the only sealer used in the future forresealing as there may be an adverse interactionbetween different sealers.TIPS: Do not seal if the temperature is below10° Celsius or over 35° Celsius. If you areresealing – test a small area first. Once sealed,routine cleaning should be with EnvironexREFRESH or a neutral detergent.FOR FURTHER TECHNICAL ASSISTANCECALL 1800 999 196 EMERGENCY INFORMATION: FIRE: S43 In case of fire use dry chemical, foam or carbon dioxide. Water spray may be used to coolexposed containers.SPILLS: Eliminate ignition sources. Collectliquid in an appropriate container or absorb onto earth, vermiculite or other noncombus-tible absorbent material. Transfer into cleanlabelled drums. Dispose of according to local government regulations. Additional informa-tion is listed in the Material Safety Data Sheet. In An Emergency Dial 000 Police or Fire Brigade.

SAFETY DIRECTIONS: Avoid contact with eyes and skin. Avoid breathing vapour or spray mist.Ensure adequate ventilation. Do not smoke or use naked flames while using. When preparing, wearelbow length PVC gloves and face shield.XN Harmful; N Dangerous for the Environment; Risks: R20/21 Harmful by inhalation and in contactwith the skin; R36/37 Irritating to eyes and respiratory system; R65 Harmful: May cause lungdamage if swallowed. R66 Repeated exposure may cause skin dryness or cracking. R67 Vapours may cause drowsiness and dizziness. R51 Toxic to aquatic organisms. R53 May cause long-term adverse effects in the aquatic environment.FIRST AID INSTRUCTIONS: For advice, contact a Poisons Information Centre (Phone Australia 131 126) or a doctor (at once). If swallowed, do NOT induce vomiting. If in eyes,wash out immediately with water. If skin or hair contact occurs, remove contaminated clothing andflush skin and hair with running water. If inhaled, remove from contaminated area. Apply artificialrespiration if not breathing.

Batch No:CONTAINS 727 mL/L XYLENE; 75 g/L NAPHTHA; 20 mL/L BUTYL ACETATE

UN 1866 RESIN SOLUTION, N.O.S. (XYLENE) CLASS 3 HAZCHEM 3[Y]E PG II

NET CONTENTS

1L 4L 10L 20L 200L






PROUDLY MADE

LOw G

LOSS

FORmULATION

BEFOREAFTER

HI-LITEHI-LITEDARKENS AND HIGHLIGHTS

THE NATURAL COLOURS OF STONE

Quality ISO 9001

3 yEARGUARANTEE

49357 Environex Endure-HiLite labels.indd 1 18/12/12 12:21 PM

‘3 YEAR WARRANTY’ **

HI LITE is a sealer that provides a darkening of the surface without the normal slippery surface that can result (in most cases). It is suitable for indoor and outdoor use and is best suited to pavers where a darker look is desired. Not suitable for honed, polished or wet cast surfaces.

Two coats applied evenly across the surface will give best results. A patchy appearance after one coat is normal. Application: Refer to the instructions for ENDURE. 2-4 coats as required. Not to be used on pool surrounds. Life span should be around 3-5 years dependent on traffic and conditions.Coverage: Allow approx. 5 square metres per litre for a finished job with 2 coats.

NET CONTENTS

1L 4L 10L 20L 200L



STONESEALSTONESEALSATIN FINISH SEALER

LITRE

STONESEALSATIN FINISH SEALER

STONESEAL is a water based acrylic sealer designed to give a satin finish to sandstone, slate and paving surfaces. It is suitable for indoor and outdoor use and is especially suited to Australian and Indian sandstones. Two coats will provide a tough seal on most surfaces that will resist staining from most household items. STONESEAL is not recommended around pools as it will result in a slippery

and dangerous surface.Application: Apply product using a lambswool applicator. Two coats should be applied about 2 hours apart. Allow 12 hours for the final coat to cure. Surfaces should not be hotter than 35 degrees or colder than 10 degrees when applying STONESEAL. Do not allow pooling or puddling as this can dry to a weak spot in the sealer. If the surface is very porous 3 coats may be required for an even finish. Resealing should be done every 2-3 years and the old sealer should simply be cleaned with HD CLEANER prior to re sealing. Area should be rinsed with REFRESH.Cleanup is in water. Be sure to clean up before the sealer dries as it is difficult to remove after it has set. Coverage: Allow approx. 5 square metres per litre for a finished job with 2 coats.

NET CONTENTS

1L 4L 10L 20L 200L



DEFENDDEFENDLITRE

SANDSTONE/LIMESTONE

CONSOLIDATOR

SALT ATTACK

CSIRO

tested and

guaranteed for

5 YEARS

DEFENDSANDSTONE/LIMESTONE

CONSOLIDATOR

DEFENDLITRE

SANDSTONE/LIMESTONE

CONSOLIDATOR

SALT ATTACK

CSIRO

tested and

guaranteed for

5 YEARS

‘5 YEAR WARRANTY & CSIRO tested’ * DEFEND (sandstone/limestone consolidator) DEFEND is a penetrating, invisible and breathable liquid that consolidates, hardens and binds the surface of porous and friable surfaces, particularly limestones and sandstones. It will assist in the prevention of salt attack and surface

breakdown common around swimming pools. DEFEND is also useful on less porous surfaces such as tile, brick, natural stone, paving and grout. Sealing with PINNACLE over DEFEND gives a 5 year warranty and sealing with TUSCAN over DEFEND gives a 3 year warranty. No Warranty will be given if the correct sealers are not used. Ensure surfaces to be treated are dry, clean and free of residues.Application: Saturate the surface with product using a clean brush, dip seal or a low-pressure hand spray. Avoid contact with surrounding areas. After 10 minutes, repeat the process. Total application rate is approximately 3-5 square metres per litre but is totally dependent on surface porosity. This allows for 2 saturating coats on most surfaces.

SYNERGY – COMBINATION CONSOLIDATOR & SEALER

SYNERGY is a new generation penetrating liquid that consolidates, hardens and binds the surface of porous and friable masonry materials. SYNERGY also possessespremium penetrating sealer properties toensure maximum protection of the stonefrom permanent staining. SYNERGY has been scientifically developed and laboratory tested against Australian Standards.SYNERGY has been developed especiallyfor use around all swimming pools to assist in prevention of salt attack and is warranted for a period of 2 years.

DIRECTIONS FOR USE: ALWAYS TESTPRODUCT ON A SMALL AREA FIRST. Ensuresurfaces to be treated are dry, clean and freefrom residue. Apply the first coat of SYNERGYto the masonry via lambswool applicator,brush or a low pressure Viton sprayer. It isESPECIALLY IMPORTANT to apply SYNERGYto all surfaces including underneath the poolcoping. (Use DEFEND for dip-sealingpurposes prior to laying to avoid adhesionissues.) Apply the second coat when the firstcoat is dry, generally between 1-4 hours depending on ambient conditions.

COVERAGE: Approximately 10 squaremetres per Litre, per coat. 2-3 coats arerequired depending on the porosity of the stone. More porous masonry requires more coats for adequate protection properties.

Note: The first coat will soak up more sealer per square metre than subsequent coats.Regardless two coats will average out asabove. Actual coverage depends on theabsorbency of the masonry. The denser the product the less sealer is required.

CLEANUP: Clean all equipment with CYCLONE.

FOR FURTHER TECHNICAL ASSISTANCECALL 1800 999 196

EMERGENCY INFORMATION: FIRE: Foam, CO2, dry powder fire extinguishers.

SPILLS: Eliminate ignition sources.Increase ventilation. Absorb onto earth,vermiculite or other absorbent material.Prevent entry into drainage systems, rivers, etc. Transfer into clearly labelled drums.Dispose of according to local government regulations. Additional information is listed in the Material Safety Data Sheet.

In an emergency Dial 000 Police or Fire Brigade.

SYNERGYXn Harmful. R10 Flammable. R36/37/38 Irritating to eyes, respiratory system and skin.R20 Harmful by inhalation. R65 Harmful: May cause lung damage if swallowed.

SAFETY DIRECTIONS: S15/16 Keep away from heat and sources of ignition. S20/21 When usingdo not eat, drink or smoke. S23 Do not breathe vapour. S24/25 Avoid contact with eyes and skin.

FIRST AID: For advice, contact a Poisons Information Centre (Phone Australia 13 11 26) ora doctor (at once). If swallowed, do NOT induce vomiting.

HAZARDOUS




PROUDLY MADE

Batch No:CONTAINS 30-60% ETHYL SILICATE COMPOUND, 30-60% ISOPROPANOL

UN1993 FLAMMABLE LIQUID, N.O.S. (ETHYL SILICATE AND ISOPROPANOL)CLASS 3 HAZCHEM 3YE PG II

SURFACE HARDENER FOR ALL MASONRY

SALT ATTACKSANDSTONE

SALT ATTACKTRAVERTINE

SALT ATTACK CONCRETE

CSIRO Te

sted

NET CONTENTS

1L 4L 10L 20L

SYNERGYCOMBINATION CONSOLIDATOR

& SEALER

2 YEARWARRANTY Tested against Australian Standards

for resistance against Salt Attack.

49204 Synergy multipack label-3.indd 1 20/11/12 10:13 AM

‘2 YEAR WARRANTY & CSIRO tested’ ***

SYNERGY (combination consolidator & penetrating sealer in one)SYNERGY is a consolidator/hardening agent especially designed to stop salt attack around swimming pools. SYNERGY is truly two products in one. SYNERGY is

a versatile product and is also ideal for use on all soft natural stone and masonry surfaces where consolidation is imperative to protecting your investment whilst still providing premium protection against staining. SYNERGY is also useful on outdoor stone and masonry furniture, pots and statues. Apply 2-4 coats with a lambswool applicator, paint brush or a low pressure hand sprayer. Always test a small area first.

The CoaTings ENDURE is a solvent based sealer designedto give a gloss finish to slate, sandstone,pavers, concrete and most masonry (notsuitable for honed masonry). A hard wearingsurface sealer, ENDURE will darken andhighlight the colours of the surface while offering protection from normal householdspills. A small test area is recommended.

DIRECTIONS FOR USE: Ensure area to besealed is clean and dry. Allow a minimum of14 days drying time after laying new pavers.Do not apply to wet surfaces or surfaces thatare below 10° Celsius or over 30° Celsius.A lambswool applicator will give best results.DO NOT USE A ROLLER. Product should beapplied in thin coats with no pooling. At least2 coats of sealer are recommended fornormal domestic use, allow from 1-4 hoursbetween coats (depending on atmosphericconditions) and 24 hours before heavytraffic. If in doubt seek advice from yourEnvironex Stonecare Specialist.

COVERAGE: For a finished job with 2 coatsallow 5 square metres per litre. This coveragemay be reduced on more porous surfaces.

CLEANUP: Clean any affected areas andequipment using Environex CYCLONE.

mAINTENANCE: All masonry sealed with ENDURE should be routinely cleaned usingEnvironex REFRESH as a routine cleaner orMAESTRO if there is a moss or mould buildup.RECOATING: ENDURE has a high lifeexpectancy (2-3 years) dependent uponapplication, traffic conditions and levelof maintenance. ENDURE should be theonly sealer used in future for re-sealing – this will avoid any compatibility issues.If sealing over a surface that has previously been sealed, test a small area first. For best results always check with yourEnvironex Technical Representative.FOR FURThER TEChNICAL ASSISTANCECALL 1800 999 196 EmERGENCY INFORmATION: SPILLS: Eliminate ignition sources. Absorb ontoearth, vermiculite or other absorbentmaterial. Transfer into clean labelled drums for disposal. S29 Do not empty into drains.FIRE: S43 In case of fire, use sand, earth, chemical powder or foam. Water spray may be used to cool containers. Additionalinformation is listed in the Material Safety Data Sheet. In an emergency Dial 000 Police or Fire Brigade.

Xn Harmful. N Dangerous for the Environment. R10 Flammable. R20/21 Harmful by inhalation and incontact with the skin. R37/38 Irritating to respiratory system and skin. R65 Harmful: May cause lungdamage if swallowed. R51 Toxic to aquatic organisms. R53 May cause long-term adverse effects in theaquatic environment.SAFETY DIRECTIONS: When spraying solutions, we recommend a respirator mask be worn by thespray operator and anyone assisting in the spray operations. Use only when there is adequate ventilationavailable. Avoid contact with skin and eyes and avoid breathing vapour or spray mist. S16 Keep awayfrom sources of ignition.FIRST AID: For advice, contact a Poisons Information Centre (Phone Australia 131 126) or a doctor(at once). If swallowed, do NOT induce vomiting. If in eyes, wash out immediately with water. If skin orhair contact occurs, remove contaminated clothing and flush skin and hair with running water. If inhaled,remove from contaminated area. Apply artificial respiration if not breathing.

Batch No:CONTAINS 700 mL/L XYLENE, 167 g/L LIqUID HYDROCARBONS

UN 1866, CLASS 3, RESIN SOLUTION FLAMMABLE, HAZCHEM 3[Y]E, PG III

NET CONTENTS

1L 4L 10L 20L 200L






PROUDLY MADE

Quality ISO 9001

ENDUREENDUREPROTECTS MASONRY AGAINST

SOILING AND STAINING

HI-LITE is a blend of solvent based sealersdesigned to darken the surface of sandstone,pavers, limestone, pebbles and concrete. It willhighlight the colours of the surface withoutleaving the usual gloss level that can result inslippery surfaces. HI-LITE is ideal for concretepavers and sandstone where a darker look isdesired. On dense stone, a higher gloss levelmay result – always test first. HI-LITE willprovide protection from normal householdspillages. For a full gloss look use EnvironexENDURE.APPLICATION: Should be done when thesurface is clean and dry. A lambswoolapplicator or spray applicator will give bestresults. DO NOT USE A ROLLER. Productshould be applied evenly across the surface ensuring no pools or puddles are left. Twocoats are recommended with around2-4 hours between coats depending onambient conditions. Curing after final coat is overnight. If foaming occurs more sealershould be applied and foaming removed. It is normal for the first coat to leave a patchyresult. The second coat will resolve this.COVERAGE: Allow 5 square metres per litre for a finished job. This can reduce on moreporous surfaces.DRYING TIME: Allow 12 hours after final coat before walking or using the surface.

CLEANUP: Cleanup applicators or sprayingequipment using Environex CYCLONE. Applicators can be left to go hard – place them back in the sealer and they will soften in about 10 minutes.RECOATING: HI-LITE will last for 3-5 yearsdepending on traffic. It is strongly advised thatHI-LITE is the only sealer used in the future forresealing as there may be an adverse interactionbetween different sealers.TIPS: Do not seal if the temperature is below10° Celsius or over 35° Celsius. If you areresealing – test a small area first. Once sealed,routine cleaning should be with EnvironexREFRESH or a neutral detergent.FOR FURTHER TECHNICAL ASSISTANCECALL 1800 999 196 EMERGENCY INFORMATION: FIRE: S43 In case of fire use dry chemical, foam or carbon dioxide. Water spray may be used to coolexposed containers.SPILLS: Eliminate ignition sources. Collectliquid in an appropriate container or absorb onto earth, vermiculite or other noncombus-tible absorbent material. Transfer into cleanlabelled drums. Dispose of according to local government regulations. Additional informa-tion is listed in the Material Safety Data Sheet. In An Emergency Dial 000 Police or Fire Brigade.

SAFETY DIRECTIONS: Avoid contact with eyes and skin. Avoid breathing vapour or spray mist.Ensure adequate ventilation. Do not smoke or use naked flames while using. When preparing, wearelbow length PVC gloves and face shield.XN Harmful; N Dangerous for the Environment; Risks: R20/21 Harmful by inhalation and in contactwith the skin; R36/37 Irritating to eyes and respiratory system; R65 Harmful: May cause lungdamage if swallowed. R66 Repeated exposure may cause skin dryness or cracking. R67 Vapours may cause drowsiness and dizziness. R51 Toxic to aquatic organisms. R53 May cause long-term adverse effects in the aquatic environment.FIRST AID INSTRUCTIONS: For advice, contact a Poisons Information Centre (Phone Australia 131 126) or a doctor (at once). If swallowed, do NOT induce vomiting. If in eyes,wash out immediately with water. If skin or hair contact occurs, remove contaminated clothing andflush skin and hair with running water. If inhaled, remove from contaminated area. Apply artificialrespiration if not breathing.

Batch No:CONTAINS 727 mL/L XYLENE; 75 g/L NAPHTHA; 20 mL/L BUTYL ACETATE

UN 1866 RESIN SOLUTION, N.O.S. (XYLENE) CLASS 3 HAZCHEM 3[Y]E PG II

NET CONTENTS

1L 4L 10L 20L 200L






PROUDLY MADE

LOw GLOSS

FORmULATION

BEFOREAFTER

HI-LITEHI-LITEDARKENS AND HIGHLIGHTS


Quality ISO 9001

3 yEARGUARANTEE

49357 Environex Endure-HiLite labels.indd 1 18/12/12 12:21 PM

ENDURE is a solvent based acrylic resin designed to give a wet look to surfaces where it is applied. It is typically associated with the gloss look of slate floors. ENDURE can be applied to slate, sandstone, and most types of pavers. It is not suitable for terracotta or very dense surfaces such as porcelain, wet cast pavers, polished or honed surfaces. To

apply, be sure that the surface is clean and dry. Always do a test patch especially on floors where an unknown sealer has been used. If any strange reactions happen, call our toll free number. We advise plans are made to sleep elsewhere on the night of application due to the odour of this product. Use a lambswool applicator and evenly spread the product on the floor. Do not allow pooling and remember thin even coats are best. More is not better with this product. After the first coat, allow around 2-3 hours before applying the second coat. In cold conditions this may be longer. Repeat the same process as the first coat ensuring no pools or puddles are left behind. Allow 12 hours before putting furniture back or walking on the floor. Any scratching of the sealer when

The sTrippers

CleaningAND

Sealing Guide

CYCLONE: will remove ENDURE.MULTI STRIP: will remove STONESEAL.MULTI STRIP is a more aggressive stripper than CYCLONE and can be used to remove ENDURE, however it evaporates much quicker. MULTI STRIP should also be used where you are unsure as to the type of sealer on the surface. If this fails, call our toll free number.Application: Stripping a floor requires patience and good work practices. Always work a small area so that you keep control and remember that dry stripper is useless – it must be kept wet to be working. Apply the stripper by flooding it onto a small area (say 4 tiles). Scrub with a scrubbing brush to get the sealer and the stripper into a solution. Yes it is messy!! Wipe it off with a rag and throw the rag away. Repeat as necessary until the tile is bare. You will need lots of rags and we suggest a breathing apparatus as the fumes are nasty. Do not leave used rags on the floor as they can leave more sealer on the floor that is hard to remove.Continue across the floor until all tiles are bare. If Stripping ENDURE, a can of MULTI STRIP may be useful at the end for difficult areas. STRIP IT is a non-ammoniated stripping compound. This product has been specifically formulated for removal of acrylic metal cross-linked polishes such as LINK SEAL 30. It is recommended for use where the use of an ammoniated stripper is not desired.STRIP IT is essentially odourless and will not yield unpleasant vapours. Application: Prepare a 1:1 solution of STRIP IT in hot water and apply to the floor with a mop. Allow five minutes for the product to react with the polish.Machine scrub, at slow speed, using a black pad, or scrub with deck scrubber, scrubbing brush or stiff broom. Pick up the resultant slurry with a mop. Rinse the floor twice with clean, hot water and clean mop.STRIP IT may be used on the floor as a light strip where only a surface coat of polish needs removing. Use at a dilution rate of up to 1:10 in hot water.---------------------------------------------------------------------------------MULTI STRIP will evaporate quickly so only use it on small areas. MULTI STRIP can take paint off so take extra care around skirting boards.

Manufactured by Environex International Pty Ltd

19 Motivation Drive, Wangara, WA 6065 Ph: (08) 9302 4000 Fax: (08) 9302 5000

FOR TECHNICAL ASSISTANCE CALL PaveWorld 9359 6028

E: [email protected]: www.paveworld.com.au

* When applied in accordance with the manufacturer’s simple directions andspecifications a 5 year warranty is provided. Terms and conditions apply.Details available on request.

** When applied in accordance with the manufacturer’s simple directions and specifications a 3 year warranty is provided. Terms and conditions apply. Details available on request.

*** When applied in accordance with the manufacturer’s simple directions and specifications a 2 year warranty is provided. Terms and conditions apply. Details available on request.

Quality ISO 9001

IN AUSTRALIA

PROUDLY MADE

CONSOLIDATORSCONSOLIDATORSSandstone/Limestone and

Masonry consolidator to harden and bind porous and friable surfaces.

CleaningAND

Sealing Guide

NET CONTENTS

1L 4L 10L 20L 200L



AMAZEAMAZEDARKENS AND HIGHLIGHTS


AMAZELITRES

AMAZE is suitable for use on most surfaces – ceramics, vitrified and slate – for the removal of left over grout smear. AMAZE is a blend of acids that will cause a fizzing response on application but it is not as strong as ANTI‑EFF or GREEN DEVIL. Its best uses will be on slate and ceramics where a minor grout smear problem has occurred. Always use gloves and dilute in 5 parts water. Apply to the

affected area and then scrub hard prior to mopping or removing the residue. It is best to work small areas at a time and rinse thoroughly. Do not use AMAZE on highly polished surfaces such as porcelain.Always use gloves, safety glasses and full length clothing.

AFTER

BEFORE

ANTI-EFFSAFETY DIRECTIONS: CORROSIVE. O Oxidiser. R35 Causes severeburns. R8 Contact with combustible material may cause fire. Avoid contactwith skin and eyes. Avoid breathing vapour or spray mist. S36 Wear suitableprotective clothing.FIRST AID: For advice, contact a Poisons Information Centre (PhoneAustralia 131 126) or a doctor (at once). If swallowed, do NOT inducevomiting. If in eyes, hold eyelids apart and flush the eye continuously withrunning water. Continue flushing until advised to stop by the PoisonsInformation Centre or a doctor, or for at least 15 minutes. If skin or haircontact occurs, remove contaminated clothing and flush skin and hair withrunning water. Continue flushing with water until advised to stop by thePoisons Information Centre or a doctor. Additional information is listed inthe Material Safety Data Sheet.



ANTI-EFF is a heavy duty acidic cleaner specifically designed to remove efflorescence from pavers, terracotta, slate or sandstone. As there are many issues surrounding efflorescence always consult your retailer or Environex International first. ANTI-EFF will react with and dissolve most surface salts that are the outcomeof efflorescence.

DIRECTIONS FOR USE: Always test first. ALWAYS WET THE SURFACEFIRST. Working in a small area, apply ANTI-EFF diluted at 1:25 to theaffected area. A fizzing reaction may occur. Scrub hard using an eagerbeaver and rinse off immediately. LIMIT CONTACT OF ANTI-EFF WITHSTONE TO NO MORE THAN 2-3 MINUTES. Repeat if necessary. We DONOT recommend this product be used any stronger than 1:15 dilutionin water as it can leach colour out of concrete pavers and masonry.MUST BE NEUTRALISED WITH REFRESH. If sealing allow a minimumof 2 days or until dry, must be clean and no traces of efflorescence left.

FOR FURTHER TECHNICAL ASSISTANCE CALL 1800 999 196

Quality ISO 9001



Ph: (08) 9302 [email protected]

CONTAINS 372 g/L NITRIC ACID, 140 g/L PHOSPHORIC ACID, UN 1760, CORROSIVE LIQUID N.O.S. (NITRIC ACID), HAZCHEM 2X, CLASS 8, PG III

IN AUSTRALIA

PROUDLY MADE

Batch No:

ANTI-EFFEFFLORESCENCE REMOVER

NET CONTENTS

1L 5L 15L

49193 Anti-Eff Label-8.indd 1 12/12/12 4:41 PM

ANTI‑EFF is a blend of acids designed to remove unsightly efflorescence salts and grout smear from pavers, terracotta and sandstone. Always wet the surface before application and dilute product with 15-25 parts water as per tech data, then neutralise with REFRESH and rinse. Mix away from surface to be treated. A fizzing reaction is normal. It isimportant to do a small area, get the product on and then scrub and rinse quickly. Always treat the whole area in a uniform manner and never use the product without

diluting it. Never allow ANTI‑EFF to dry on the surface. Thorough rinsing is vital. (The floor must be rinsed with REFRESH to take off any residue and left over dirt. Not to be used on polished surfaces such as porcelain.) Suitable for most surfaces. Best use is on concrete pavers.Always use gloves, safety glasses and full length clothing.Coverage: One Litre should clean approx. 10 square metres.

BAN RUST is a remarkable blend of acidic cleaning agents which easily and rapidly converts those brownish coloured bore water stains allowing complete removal from all masonry and other building surfaces. BAN RUST also finds application in the marine industry for the removal of rust stains from fibreglass and other surfaces and water line staining caused by bacterial action.Application: BAN RUST is supplied in a ready to use form and incorporates a unique wetting agent to ensure total penetration into the stain to be removed. Use undiluted or 1-10 parts water (always test first). BAN RUST may be spray, brush or roller applied over contaminated surface. Allow 5-10 minutes duration or until stain has disappeared before flooding treated surface with water to remove any excess BAN RUST. For very heavily stained surfaces a second application of BAN RUST may be necessary.

FLOOR SPARKLE is a heavy duty powerful water-based alkaline floor cleaner designed for safe and effective removal of heavy grease and oil deposits encountered in kitchen, food preparation areas and plant and machinery workshops. Light cleaning 1:100, Medium cleaning 1:50, and Heavy duty cleaning 1:10.

NET CONTENTS

1L 4L 10L 20L 200L



CLEARSEALCLEARSEALLITRE

MASONRY SEALERAND PRE GROUT

TREATMENT

CLEARSEALMASONRY SEALER AND PRE GROUT

TREATMENT

CLEARSEAL A water based sealer best used as a pre seal to help with cleanup or as a sealer for masonry walls. Application is best done using a sprayer. Ensure only ONE COAT is applied and use only enough to soak the surface. Excess product should be wiped away while it is still wet.DO NOT LET POOLS AND PUDDLES SIT TO DRY. If any whitening occurs after drying too much product has

been applied and you will need to call the hotline. Allow 6-8 hours before commencing grouting and be sure to wipe off all excess grout during cleanup. Cleanup is with water. Avoid spraying CLEARSEAL near timber or metal.Coverage: Allow approx. 3-5 square metres per litre. More porous surfaces may use even more. Resealing should be done every 3-5 years.

NET CONTENTS

1L 4L 10L 20L 200L



PINNACLEPINNACLELITRE

PENETRATING SEALERFOR MAXIMUM STAIN

PROTECTION

PINNACLEPENETRATING SEALER FOR

MAXIMUM STAIN PROTECTION

‘5 YEAR WARRANTY’ *PINNACLE is a blend of very high performing resins designed to give maximum stain protection from household spills. It is suitable for indoor and outdoor use and may alter the appearance of the surface being sealed (slight darkening may occur on some surfaces). It will not interfere

with the finish or the slipperiness of the surface. Application: Apply product using a lambswool applicator or a solvent resistant spray pack for commercial areas. The area to be sealed must be clean and dry prior to sealing. Remember that any stains or marks that are sealed over will be almost impossible to remove later. Two light coats should be applied such that the surface is uniformly wet with the product, remove excess sealer, resealing 1-2 coats as required. Allow one hour between coats and 8 hours after completion before using the area. Ideally this is overnight. Maintenance and cleaning should be done using REFRESH. Harsh chemical cleaners such as acids, degreasers, Jif, Handy Andy should be avoided as they can break down the sealer quickly. Cleanup is not necessary as the resin in this product will turn to powder in the applicator. Simply dust off the following day. Surfaces sealed with PINNACLE will not require re sealing for many years and will not require stripping. After 5 years apply 1-2 coats of Pinnacle as required to protect your investment.Allow approx. 5 square metres per litre for a finished job of 2 coats.

NET CONTENTS

1L 4L 10L 20L 200L



TUSCANTUSCAN SEALLITRE

PENETRATING SEALER FOR PROTECTION AGAINST

STAINING ON TILES & PAVERS

TUSCANPENETRATING SEALER FOR

PROTECTION AGAINST STAINING ON TILES & PAVERS

‘3 YEAR WARRANTY’ **

TUSCAN SEAL is a solvent based sealer designed to give stain protection from common spills. TUSCAN SEAL will leave the surface with a natural finish but may alter the appearance depending on the stone.Application: Apply product using a lambswool applicator

or a chemical resistant spray pack. Do not allow to foam as it may cause staining (if foaming occurs there is not enough sealer being used). Two soaking coats are recommended with about 30 minutes between coats. Final curing takes about 2 hours. Coverage: Allow approx. 5 square metres per litre for a finished job on most surfaces. More porous surfaces will use more than this. Cleanup is not necessary – allow the applicator to dry and then dust out the next day.Resealing should be done every 3-5 years. Stripping is not necessary – clean areawith HD CLEANER, GREEN DEVIL, SAPPHIRE, BAN RUST or ANTI‑EFF rinse with REFRESH and simply re-seal.

NET CONTENTS

1L 4L 10L 20L 200L



GREEN DEVILGREEN DEVILLITRES

GROUT SMEAR REMOVERFOR SANDSTONE &

TERRACOTTA

GREEN DEVILGROUT SMEAR REMOVER FOR SANDSTONE & TERRACOTTA

GREEN DEVIL is a blend of acids best suited to removing grout smear from terracotta and sandstone. This product is NOT to be used on coloured concrete pavers. Mix with 10 parts water and flood onto a small area. A fizzing reaction is normal as the product attacks the cement smear. Scrub hard and rinse off thoroughly. Do not allow to dry on the surface. A stronger mix may be used on sandstone

– up to 5 parts water for difficult stains. (The floor must be rinsed withREFRESH to take off any residue and left over dirt. Not to be used on polishedsurfaces such as porcelain.)Always use gloves, safety glasses and full length clothing.Coverage: One Litre should clean approx. 10 square metres.

NET CONTENTS

1L 4L 10L 20L 200L



HD CLEANERHD CLEANERLITRES

HEAVY DUTYCLEANER FOR ALL SURFACES

HD CLEANERHEAVY DUTY CLEANER FOR ALL

SURFACES

HD CLEANER is a highly alkaline caustic cleaner designed for the cleaning of surfaces prior to sealing either for the first time or for later resealing. The strength of HD CLEANER makes it ideal to remove dirt deposits in kitchens or living areas that may have built up over time. Best results will be obtained with a dilution in 20 parts hot water. Flood the affected area and allow to stand for

2-3 minutes. Scrub vigorously until the solution on the floor is dirty and then mop off or remove with a wet vac. (The floor must be rinsed with REFRESH to take off any residue and left over dirt. Not to be used on polished surfaces.)Always use gloves, safety glasses and full length clothing.

MAESTRO is a super concentrated chlorinated cleaner designed to remove moss, mould, leaf stains and timber tannin stains from tiles and pavers. It can be used neat or diluted – we suggest a dilution of 1 part MAESTRO to 4 parts water for most problems while difficult stains may need neat product.

APPLICATION is by way of watering can, bucket or straight from the bottle. Allow the product to dwell for 5 minutes and then scrub and rinse. Moss and mould will be easily removed and may even be hosed off. Leaf stains may require scrubbing but it is mainly the chemistry that will do the work. DO NOT SPILL THIS PRODUCT ON YOURCLOTHES. Once clean rinse area thoroughly.

FOR FURTHER TECHNICAL ASSISTANCE CALL 1800 999 196 C Corrosive Risk Phrases: R31 Contact with acids liberates toxic gas, R34 Causes burns, R8 Contactwith combustible material may cause fire. Product will irritate the eyes, nose, throat and skin.SAFETY DIRECTIONS: S1/2 Keep locked up and out of the reach of children. S28 After contact withskin, wash immediately with plenty of water. S45 In case of accident or if you feel unwell, seek medicaladvice immediately (show the label where possible). S50 Do not mix with combustible material. Avoidcontact with skin and eyes. Avoid contact with clothing. Avoid breathing vapour (or) spray mist. Ensureadequate ventilation when using. Use clean containers for dispensing. Store under cover in a dry, clean,cool, well ventilated place away from sunlight. Store and transport in an upright container.FIRST AID: For advice, contact a Poisons Information Centre (Phone Australia 131 126) or a doctor(at once). If swallowed, do NOT induce vomiting. If in eyes, hold eyelids apart and flush the eyecontinuously with running water. If skin or hair contact occurs, remove contaminated clothing and flushskin and hair with running water.

HAZARDOUS




PROUDLY MADE

Batch No:CONTAINS MINIMUM 100 g/L AVAILABLE CHLORINE PRESENT AS SODIUM HYPOCHLORITE WHEN PACKED

UN 1791, HYPOCHLORITE SOLUTION, CLASS 8, HAZCHEM 2X, PG III

NET CONTENTS

5L 15L

BEFORE AFTER

MAESTROMAESTROCHLORINATED CLEANER FOR REMOVING MOSS,

MOULD & LEAF STAINS

Quality ISO 9001

49210 Maestro multipack label-3.indd 1 14/01/13 11:48 AM

MAESTRO is a strongly chlorinated cleaner designed to remove organic stains such as moss and mould, leaf tannins and timber stains. It is best applied neat or diluted 1-5 parts water onto the affected area. Move the product around until the stains fade away – use a broom or a scrub brush – and then rinse thoroughly. Repeat if necessary. Do notget MAESTRO on clothing.

Always use gloves, safety glasses and full length clothing.Coverage: One Litre should clean approx. 5 square metres.

NET CONTENTS

1L 4L 10L 20L 200L



REFRESHREFRESHLITRE

ROUTINE CLEANERFOR ALL SEALED

SURFACES

REFRESHROUTINE CLEANER FOR ALL

SEALED SURACES

REFRESH (daily or weekly cleaner) is a pH Neutral Detergent designed for routine cleaning of all sealed surfaces. The product will gently clean and condition floors ensuring long sealer life. Dilute at 1:50 in warm water and mop on and then off the surface to be treated. Rinse with clean water to finish.

CAUTIONKEEP OUT OF REACH OF CHILDREN

READ SAFETY DIRECTIONS BEFORE OPENING OR USINGDO NOT SWALLOW

S21 MULTI PURPOSE CLEANER is a remarkable hard surface cleaningconcentrate which has outstandinggrease cutting action through theincorporation of a broad range ofsequestrants, sur factants andalkaline cleaning components. Thesecomponents are further boosted with a specialty solvent component tosynergistically dissolve and emulsifyalmost any grease or grime whichcan be encountered. The alkalinity of S21 MULTIPURPOSE CLEANER hasbeen achieved without using caustic based products and as such will not affect aluminium surfaces.

S21 MULTIPURPOSE CLEANER finds application in diverse areas including degreasing of automobile engines,industrial equipment, marine engines and bilges of boats, cooking ovens, aluminium filters in cooking fans,oily tools, kitchen work benches and stoves, grease removal from clothes and even grease removal and tyremarks from dr iveways andconcrete surfaces.

APPLICATION RATES:Engines, boat bilges, drivewaysetc. – Use neat or dilute 1:1 in hot water depending on degree of grease build-up.Work benches, stoves etc. – Dilute1 part S21 MULTIPURPOSE CLEANERto 2 parts of water depending on thetype of soil to be removed (moregrease, lower dilution – less water).Greasy clothes – Add 150-300 mls per7 kg of wash, or a normal householdwash load. When adding to a washingmachine S21 MULTIPURPOSECLEANER should be diluted beforeaddition to ensure no adverse effectsfrom adding neat S21 MULTIPURPOSECLEANER to clothes.Aluminium filters for cooking fumehoods – Dilute 1:10 with hot waterand leave filter to soak for severalhours. Agitation will improve grease removal.Tyre marks – Apply neat, allow todwell on the stain for about 60seconds, scrub with a stiff brush and rinse off with copious amounts ofwater If the mark remains, repeatthe process.

FOR FURTHER TECHNICAL ASSISTANCE CALL 1800 999 196




PROUDLY MADE

Batch No:

NET CONTENTS

1L 5L 15L 200L

SAFETY DIRECTIONS: Strongly alkaline. Avoid contact with skin and eyes.R36/38 Irritating to eyes and skin. S37/39 Wear suitable gloves andeye/face protection.FIRST AID: For advice, contact a Poisons Information Centre (Phone Australia131 126) or a doctor (at once). If swallowed, do NOT induce vomiting. If in eyes,hold eyelids apart and flush the eye continuously with running water. Continueflushing until advised to stop by the Poisons Information Centre or a doctor, orfor at least 15 minutes. If skin or hair contact occurs, remove contaminatedclothing and flush skin and hair with running water.

S21 MULTI PURPOSE CLEANER

S21 MULTI PURPOSE CLEANER

CONTAINS 50 g/L ALKALINE SALTS

HARD SURFACE CLEANER WITH OUTSTANDING GREASE CUTTING ACTION

QualityISO 9001

49231 S21 label-5.indd 1 29/11/12 10:23 AM

S21 MULTI PURPOSE CLEANER is a remarkable hard surface cleaning concentrate which has outstanding grease cutting action through the incorporation of a broad range of sequestrants, surfactants and alkaline cleaning components. These components are further boosted with a specialty solvent component to synergistically dissolve and emulsify almost any grease or grime which can be encountered. The alkalinity of S21 MULTI PURPOSE

CLEANER has been achieved without using caustic based products.Tyre Marks – Apply neat, allow to dwell on the stain for about 60 seconds, scrub with a stiff brush and rinse off with copious amounts of water. If the mark remains, repeat the process.

SAPPHIRE is a blend of acids and nonionic surfactants designed to remove stubborn stains such as red dirt etc. from hard surfaces such as masonry, ceramics, porcelain and glass. Do not use on concrete paving.Application: Apply SAPPHIRE diluted to 1:20 with hot water and apply to stains, allow to stand for a few minutes, then work with a brush or soft scouring pad (avoid scratching) and then rinse clean.

SD 6 is an alkaline iron stain remover that will rapidly convert yellow-brown insoluble iron stains to a pale green water-soluble solution. It will also convert other metal oxide stains such as manganese to soluble forms. SD 6 is a safe alternative to oxalic acid cleanersApplication: Apply SD 6 neat or diluted with water, depending on the severity of the stain. Wash off immediately with tap water.If the surface is not washed off immediately, then air will re-convert the solubilized iron back to the insoluble form and the stain will return.

VANISH Is a two part bleach cleaner designed for the cleaning of sandstone and transition metal colour bodies from siliceous surfaces. Do not use on man-made pavers.

NOTE: Never use any acid on any marble, travertine or limestone surface.CLEANING TIP: Never let the surface dry and always rinse off thoroughly.Always test a small area first.

peneTraTing sealers

NET CONTENTS

1L 4L 10L 20L 200L



ADVANTAGEADVANTAGELITRE

PENETRATING SEALERFOR PORCELAIN &

DENSE STONE

ADVANTAGEPENETRATING SEALER FOR

PORCELAIN & DENSE STONE

ADVANTAGE is to be used on dense materials such as porcelain and granite. It will leave the surface with a natural finish (polished in the case of porcelain) and will protect against common spills. Preparation is the key to success with this product. The area to be sealed should be cleaned using a dilute

HD CLEANER and all grout residue and dirt should be removed. Application: Apply product using a sprayer or lambswool applicator. One coat should be allowed to dry on the surface. Do not flood the product on – a good even thin coverage is best. For the second coat apply ADVANTAGE to a small area and then use a soft cloth or a white buffing pad if using a machine. This “spray buff” will bring out the natural finish of the surface. A polished porcelain will have a high polish as it does prior to grouting. Continue across the floor buffing small quantities of product until complete. Allow 2 hours for curing. Only clean treated floors with REFRESH. Cleanup is not necessary as applicators can be dusted out the following day. Coverage: Allow approx. 20 square metres per litre for a finished job on most dense surfaces. More porous surface will use more product.

FOR TECHNICAL ASSISTANCE CALL Pave World 9359 6028

Always test a small area first and call us if in any doubt.

CLEANERSIncorrect use of certain

cleaners can cause permanent damage. Always add chemicals to water not water to

chemicals. Always test a small area first.

SEALERS There are 2 types of

sealer – those that penetrate and those which leave a surface coating. The

penetrating sealers will leave a natural finish but may alter the colour depending on type of stone. The

surface coatings will alter the appearance of the surface to differing degrees depending on which product is chosen.

SEALERS

CLEANERS

consolidators t s - s3-ap-southeast-2. · pdf fileresealing should be done every 2-3 years and...

Documents