contact/phone: upx322 and upx430
TRANSCRIPT
ENGINEERING DATAULH109 ULH214 ULH322 ULH430
Total input power (watts) 20 40 60 80
Total Operating AMPS .17 .34 .50 .70
Power Factor .99 .99 .99 .99
REV-10/05
PRODUCT SPECIFICATIONSLamp 20W-12-volt halogen bi-pin lamps supplied with fixture • Projected 6,000 hour life based on actual operating voltage infixture.Transformer Integral Electronic 120 to 12-volt step downtransformer is accessible for maintenance without having toremove fixture.Housing Extruded aluminum • Designer white, black, brushedbronze or brushed silver finish.Reflector Specular aluminum reflector behind each lamp.Diffuser Clear prismatic tempered glass lens for maximum lighttransmission • Reverse-angled to minimize preceived brightness • Captive lens has hinged design for tool-less relamping • Spring-loaded retention bar prevents lens from accidently being bumpedloose.Switch Convenient integral Hi/Lo/Off rocker switch.Dimming For best results use dimmer specifically designed for usewith electronic low voltage transformers.Labels UL Listed.
DIMENSIONS
UNDERCABINET LIGHTINGPRO-HALOGEN
20W - 12-volt Halogen Lamps
ULH109, ULH214, ULH322 and ULH430
I1.1.0
Project:
Fixture Type:
Location:
Contact/Phone:
PRODUCT DESCRIPTIONThe Pro-Halogen modular series with integral electronictransformer operates 12-volt halogen lamps to deliver the bestcolor rendering with maximum light output and lamp life. Theefficient operation of low voltage lamps, along with a uniquehousing/reflector system, reduces mounting surface temperatureswell below what is typical for halogen undercabinet fixtures. Pro-Halogen fixtures are optimized for fast permanent installation,mounting either flush to the rear backsplash or to the front lip ofcabinetry to suit project conditions and homeowner preference.
INSTALLATIONULH series fixtures optimized with a center rear wiring accesscompartment and push-in 3-wire electrical connectors for quickelectrical connection without having to open the fixture or removethe lens. Rear wiring access compartment covers provided withpush-in connector for non-metallic cable and knockout for feed thruwiring capability. Multiple off-center knockouts provided in two,three and four lamp fixtures. Die-cast fitting for 3/8” flexible metalconduit supplied in a hardware pack. Fixtures may be mountedflush to the backsplash or up against the front lip of the cabinetryusing captive external mounting screws.Portable To install as a portable fixture, use the 3-wire groundedcord & plug (ULH-CP sold separately).Optional Direct Wire Optional direct wire module (ULH-DWMsold separately) facilitates code-compliant installation of fixture atfront edge of cabinetry. Supplied with 36” field-shortenablejumper cord to bring power to either end of the fixture.Electrically Connecting Multiple Fixtures Up to 10 fixturesmay be electrically joined together using either the straight joinerconnector supplied with each fixture or the optional JC3 jumpercords. See accessories table for lengths and finishes.
ACCESSORIESCatalog No. DescriptionJC3-8-WH,-BL 8” Jumper Cord
JC3-17-WH,-BL 17” Jumper Cord
JC3-26-WH,-BL 26” Jumper Cord
ULH-CONN 3/8” Miniature Die-Cast Electrical Connector
ULH-CP-WH,-BL 3-Wire Grounded Cord & Plug
ULH-DWM-WH,-BL Direct Wire Module
PRODUCT CODES
Catalog Number Finish Overall Length Lamp
ULH109-BL Black 9 1/2” 1-20W
ULH109-BZ Brushed Bronze 9 1/2” 1-20W
ULH109-SL Brushed Silver 9 1/2” 1-20W
ULH109-WH Designer White 9 1/2” 1-20W
ULH214-BL Black 14” 2-20W
ULH214-BZ Brushed Bronze 14” 2-20W
ULH214-SL Brushed Silver 14” 2-20W
ULH214-WH Designer White 14” 2-20W
ULH322-BL Black 22” 3-20W
ULH322-BZ Brushed Bronze 22” 3-20W
ULH322-SL Brushed Silver 22” 3-20W
ULH322-WH Designer White 22” 3-20W
ULH430-BL Black 30” 4-20W
ULH430-BZ Brushed Bronze 30” 4-20W
ULH430-SL Brushed Silver 30” 4-20W
ULH430-WH Designer White 30” 4-20W
PRO-HALOGEN 5 MINUTE DIRECT-WIRE INSTALLATION
Step 1 Attach supplywires to rear access cover.
Step 2 Connect supplywires to fixture leadsusing push-in connectors.
Step 3 Mount fixture tocabinet bottom usingcaptive mounting screws.
Maximum cabinet bottom contact temperature: less than 60˚ C.
1"
4 1/2"
I1.1.0
LIGHTING APPLICATION DATA
FOOTCANDLES ON HORIZONTAL WORK SURFACE
Beam Width
Fixture
15"
BA C
D
12"
12" 12"
24"
Footcandles*Beam
Cat # Lamp Width A B C D
ULH109 (1) 20-watt Halogen 21” 8 29 26 34
ULH214 (2) 20-watt Halogen 23” 14 52 46 52
ULH322 (3) 20-watt Halogen 31” 23 72 63 59
ULH430 (4) 20-watt Halogen 36” 23 74 69 61
*Beam width defined as 50% of maximum footcandles
Rear wall reflectance 50%Counter Surface Reflectance 20%
UNDERCABINET LIGHTINGPRO-HALOGEN
20W - 12-volt Halogen Lamps
ULH109, ULH214, ULH322 and ULH430
1300 S. Wolf Road • P.O. Box 5065 • Des Plaines, IL 60017-5065 • Phone (847) 827-9880 • Fax (847) 827-2925
220 Chrysler Drive • Brampton, Ontario • Canada L6S 6B6 • Phone (905) 792-7335 • Fax (905) 792-0064
Visit us at www.junolightinggroup.com Printed in U.S.A. ©2005 Juno Lighting, Inc.
REV-4/05
PRODUCT SPECIFICATIONS
Lamp 25watt 120volt halogen G8 bi-pin lamps supplied withfixture • 2,000 hour rated life.
Housing Extruded aluminum painted designer white.
Reflector Specular aluminum inner reflector.
Diffuser Frosted tempered glass lens.
Switch Convenient integral Hi/Lo/Off rocker switch.
Dimming Use better quality incandescent wall dimmers.
Labels UL Listed.
DIMENSIONS
UNDERCABINET LIGHTINGLINE VOLTAGE HALOGEN
25W - 120Volt Halogen Lamps
UH106, UH212 and UH318
I1.2.0
Project:
Fixture Type:
Location:
Contact/Phone:
1 5/16"
3"
PRODUCT DESCRIPTION
The Line Voltage Halogen modular series provides economicalhalogen lighting by utilizing 120-volt halogen lamps that do notrequire a transformer. Fixtures may be dimmed to create night andmood lighting via fixture mounted hi-lo-off switch or wall mounteddimmers. The compact design is ideal for undercabinet, undershelfand task lighting where bright, halogen light and dimmingcapability is desired.
INSTALLATION
UH series fixtures mount with captive mounting screws and installwithout having to open the fixture or remove the lens.
Portable All UH series fixtures are supplied with 6’ power cordand removable insulation displacement type plug to allow fieldshortening. The power cord attaches to either side of the fixture.Note: Allow 21/2” of side clearance for insertion/removal of thepower cord.
Direct Wire UH fixtures may be direct-wired with non-metalliccable or flexible metal conduit using the optional DWM1 DirectWire Module accessory (sold separately). The DWM1 is suppliedwith a 36” field-shortenable jumper cord to bring power to eitherend of the UH fixture. Note: Allow 21/2” of side clearance forinsertion/removal of the jumper cord.
Electrically Connecting Multiple Fixtures Up to 750 watts ofUH fixtures may be electrically joined together using either thestraight joiner connector supplied with each fixture or the optionalJC2 jumper cords. See accessories below for lengths.
ACCESSORIESCatalog No. DescriptionDWM1-WH Direct Wire Module
JC2-8-WH 8” Jumper Cord
JC2-17-WH 17” Jumper Cord
JC2-26-WH 26” Jumper Cord
T925 25W-120V Replacement Lamp
PRODUCT CODES
Catalog Number Finish Overall Length Lamp
UH106-WH Designer White 6 1/8” 1-25W
UH212-WH Designer White 12 1/8” 2-25W
UH318-WH Designer White 17 3/4” 3-25W
ENGINEERING DATAUH106 UH212 UH318
Total input power (watts) 25 50 75
Total Operating AMPS .21 .42 .63
Power Factor .99 .99 .99
1300 S. Wolf Road • P.O. Box 5065 • Des Plaines, IL 60017-5065 • Phone (847) 827-9880 • Fax (847) 827-2925
220 Chrysler Drive • Brampton, Ontario • Canada L6S 6B6 • Phone (905) 792-7335 • Fax (905) 792-0064
Visit us at www.junolightinggroup.com Printed in U.S.A. ©2005 Juno Lighting, Inc.
I1.2.0
LIGHTING APPLICATION DATA
FOOTCANDLES ON HORIZONTAL WORK SURFACE
Beam Width
Fixture
15"
BA C
D
12"
12" 12"
24"
Footcandles*Beam
Cat # Lamp Width A B C D
UH106 (1) 25-watt Halogen 12” 8 33 19 18
UH212 (2) 25-watt Halogen 22” 12 60 35 35
UH318 (3) 25-watt Halogen 28” 19 93 51 48
*Beam width defined as 50% of maximum footcandles
Rear wall reflectance 50%Counter Surface Reflectance 20%
UNDERCABINET LIGHTINGLINE VOLTAGE HALOGEN
25W - 120Volt Halogen Lamps
UH106, UH212 and UH318
REV-4/05
PRODUCT SPECIFICATIONS
Lamp (1) 18W lamp (ULX109), (2) 18W lamps (ULX212), (3)18W lamps (ULX318) and (4) 18W lamps (ULX424) supplied withfixture • 10,000 hour lamp life.
Transformer Integral 12V electronic transformer.
Housing Formed steel fixture body for maximum strength, paintedappliance white.
Switch Hi/Lo/Off switch.
Diffuser Frosted tempered glass lens.
Labels UL Listed.
DIMENSIONS
UNDERCABINET LIGHTINGDIRECT WIRE LOW VOLTAGE XENON
18W Xenon Lamp
ULX109, ULX212, ULX318 and ULX424
I1.3.0
Project:
Fixture Type:
Location:
Contact/Phone:
3 1/2"
1 3/16"
PRODUCT CODES
Catalog Number Finish Overall Length Lamp
ULX109-WH Appliance White 9 1/2” 1-18W
ULX212-WH Appliance White 12” 2-18W
ULX318-WH Appliance White 18” 3-18W
ULX424-WH Appliance White 24” 4-18W
PRODUCT DESCRIPTION
The Direct Wire Low Voltage Xenon series with integral 12-voltelectronic transformer offers an economical direct wire sheet metalundercabinet alternative using long-life 12-volt xenon lamps.
INSTALLATION
ULX fixtures may be direct-wired with non-metallic cable or flexiblemetal conduit using the 3/8” die-cast fitting supplied with thefixture. Connect at knockouts located at rear and ends of fixture.
Portable To install as a portable fixture, use the 3-wire groundedcord & plug (ULH-CP sold separately).
ACCESSORIESCatalog No. DescriptionULH-CONN 3/8” Miniature Die-Cast Electrical Connector
ULH-CP-WH,-BL 3-Wire Grounded Cord & Plug
ENGINEERING DATAULX109 ULX212 ULX318 ULX424
Total input power (watts) 17.0 33.6 49.9 65.6
Total Operating AMPS .14 .28 .42 .55
Power Factor .99 .99 .99 .99
UNDERCABINET LIGHTINGDIRECT WIRE LOW VOLTAGE XENON
18W Xenon Lamp
ULX109, ULX212, ULX318 and ULX424
I1.3.0
LIGHTING APPLICATION DATA
FOOTCANDLES ON HORIZONTAL WORK SURFACE
Beam Width
Fixture
15"
BA C
D
12"
12" 12"
24"
*Beam width defined as 50% of maximum footcandles
Rear wall reflectance 50%Counter Surface Reflectance 20%
Footcandles*Beam
Cat # Lamp Width A B C D
ULX106 (1) 18-watt Xenon 21” 14 25 20 25
ULX212 (2) 18-watt Xenon 24” 30 52 42 49
ULX318 (3) 18-watt Xenon 28” 40 72 55 59
ULX424 (4) 18-watt Xenon 32” 44 75 64 61
1300 S. Wolf Road • P.O. Box 5065 • Des Plaines, IL 60017-5065 • Phone (847) 827-9880 • Fax (847) 827-2925
220 Chrysler Drive • Brampton, Ontario • Canada L6S 6B6 • Phone (905) 792-7335 • Fax (905) 792-0064
Visit us at www.junolightinggroup.com Printed in U.S.A. ©2005 Juno Lighting, Inc.
ENGINEERING DATA (120V)UFL12 UFL22 UFL34 UFL46
Total input power (watts) 8.4 15.3 22.1 30.3
Total Operating AMPS .13 .23 .32 .45
Power Factor .52 .53 .57 .56
REV-1/07
PRODUCT SPECIFICATIONS
Lamp Latest generation of high-efficiency (HE), high colorrendering 3000K T5 tri-phosphor fluorescent lamps • 10,000 hourrated lamp life.*
Ballast State of the art 120V electronic ballast instantly starts lampand operates without flicker or hum.
Housing Formed steel fixture body for maximum strength, paintedappliance white or silver.
Switch Convenient on/off switch.
Diffuser Extruded non-yellowing clear UV/impact resistant acryliclens.
Labels UL Listed and Energy Star compliant • Complies withCalifornia’s Title 24 energy code.
DIMENSIONS
UNDERCABINET LIGHTINGDIRECT WIRE FLUORESCENT
8W, 14W, 21W & 28W
T5 HE Fluorescent Lamps
UFL12, UFL22, UFL34 and UFL46
I1.4.0
Project:
Fixture Type:
Location:
Contact/Phone:
1 1/16"
2 5/8"
PRODUCT CODES
Catalog Number Finish Overall Length Lamp
UFL12-WH Appliance White 12 7/16” 8W T5
UFL12-SL Silver 12 7/16” 8W T5
UFL22-WH Appliance White 22 3/4” 14W T5 HE
UFL22-SL Silver 22 3/4” 14W T5 HE
UFL34-WH Appliance White 34 1/2” 21W T5 HE
UFL34-SL Silver 34 1/2” 21W T5 HE
UFL46-WH Appliance White 46 5/16” 28W T5 HE
UFL46-SL Silver 46 5/16” 28W T5 HE
PRODUCT DESCRIPTION
Direct Wire Fluorescent luminaires offer highly efficient illuminationin a shallow, easy-to-conceal profile. Ideal for undercabinet,undershelf, and task lighting, where maximum energy efficiency,long lamp life, and cool operation are desired.
INSTALLATION
UFL fixtures may be direct-wired with non-metallic cable or flexiblemetal conduit using the 3/8” die-cast fitting supplied with thefixture. Connect at knockouts located at rear and ends of fixture.
Portable To install as a portable fixture, use the 3-wire groundedcord & plug (ULH-CP sold separately).
ACCESSORIESCatalog No. DescriptionULH-CONN 3/8” Miniature Die-Cast Electrical Connector
ULH-CP-WH,-BL 3-Wire Grounded Cord & Plug
* 8W T5 tri-phosphor lamp rated at 7,500 hours.
MAXIMUM ENERGY EFFICIENCY:8 watts = 40 watts halogen14 watts = 75 watts halogen21 watts = 100 watts halogen28 watts = 150 watts halogen
UNDERCABINET LIGHTINGDIRECT WIRE FLUORESCENT
8W, 14W, 21W & 28W
T5 HE Fluorescent Lamps
UFL12, UFL22, UFL34 and UFL46
I1.4.0
LIGHTING APPLICATION DATA
FOOTCANDLES ON HORIZONTAL WORK SURFACE
Beam Width
Fixture
15"
BA C
D
12"
12" 12"
24"
*Beam width defined as 50% of maximum footcandles
Rear wall reflectance 50% 8 watts equivalent to 40 watts of halogenCounter Surface Reflectance 20% 14 watts equivalent to 75 watts of halogen
21 watts equivalent to 100 watts of halogen28 watts equivalent to 150 watts of halogen
Footcandles*Beam
Cat # Lamp Width A B C D
UFL12 8-watt T5 24” 32 77 68 93
UFL22 14-watt T5 HE 31” 64 135 130 157
UFL34 21-watt T5 HE 41” 66 140 131 140
UFL46 28-watt T5 HE 50” 83 171 166 170
1300 S. Wolf Road • P.O. Box 5065 • Des Plaines, IL 60017-5065 • Phone (847) 827-9880 • Fax (847) 827-2925
220 Chrysler Drive • Brampton, Ontario • Canada L6S 6B6 • Phone (905) 792-7335 • Fax (905) 792-0064
Visit us at www.junolightinggroup.com Printed in U.S.A. ©2007 Juno Lighting, Inc.
ENGINEERING DATAUPX109 UPX214 UPX322 UPX430
Total input power (watts) 20 40 60 80
Total Operating AMPS .17 .34 .50 .70
Power Factor .99 .99 .99 .99
REV-2/07
PRODUCT SPECIFICATIONSLamp 20W-12-volt xenon bi-pin high output lamps supplied withfixture • Projected 10,000 hour life based on actual operatingvoltage in fixture.Transformer Integral Electronic 120 to 12-volt step downtransformer is accessible for maintenance without having toremove fixture.Housing Extruded aluminum • Designer white, black, brushedbronze or brushed silver finish.Reflector Specular aluminum reflector behind each lamp.Diffuser Clear prismatic tempered glass lens for maximum lighttransmission • Reverse-angled to minimize preceived brightness • Captive lens has hinged design for tool-less relamping • Spring-loaded retention bar prevents lens from accidently being bumpedloose.Switch Convenient integral Hi/Lo/Off rocker switch.Dimming For best results use dimmer specifically designed for usewith electronic low voltage transformers.Labels UL Listed.
DIMENSIONS
UNDERCABINET LIGHTINGPRO-XENON
20W - 12-volt Xenon Lamps
UPX109, UPX214, UPX322 and UPX430
I1.5.0
Project:
Fixture Type:
Location:
Contact/Phone:
PRODUCT DESCRIPTIONThe Pro-Xenon modular series with integral electronic transformeroperates 12-volt halogen lamps to deliver the best color renderingwith maximum light output and lamp life. The efficient operation oflow voltage lamps, along with a unique housing/reflector system,reduces mounting surface temperatures well below what is typicalfor xenon undercabinet fixtures. Pro-Xenon fixtures are optimizedfor fast permanent installation, mounting either flush to the rearbacksplash or to the front lip of cabinetry to suit project conditionsand homeowner preference.
INSTALLATIONUPX series fixtures optimized with a center rear wiring accesscompartment and push-in 3-wire electrical connectors for quickelectrical connection without having to open the fixture or removethe lens. Rear wiring access compartment covers provided withpush-in connector for non-metallic cable and knockout for feed thruwiring capability. Multiple off-center knockouts provided in two,three and four lamp fixtures. Die-cast fitting for 3/8” flexible metalconduit supplied in a hardware pack. Fixtures may be mountedflush to the backsplash or up against the front lip of the cabinetryusing captive external mounting screws.Portable To install as a portable fixture, use the 3-wire groundedcord & plug (ULH-CP sold separately).Optional Direct Wire Optional direct wire module (ULH-DWMsold separately) facilitates code-compliant installation of fixture atfront edge of cabinetry. Supplied with 36” field-shortenablejumper cord to bring power to either end of the fixture.Electrically Connecting Multiple Fixtures Up to 10 fixturesmay be electrically joined together using either the straight joinerconnector supplied with each fixture or the optional JC3 jumpercords. See accessories table for lengths and finishes.
ACCESSORIESCatalog No. DescriptionJC3-8-WH,-BL 8” Jumper Cord
JC3-17-WH,-BL 17” Jumper Cord
JC3-26-WH,-BL 26” Jumper Cord
ULH-CONN 3/8” Miniature Die-Cast Electrical Connector
ULH-CP-WH,-BL 3-Wire Grounded Cord & Plug
ULH-DWM-WH,-BL Direct Wire Module
UPX-LAMP 12V 20W Bi-Pin Xenon High Output Lamp
PRODUCT CODES
Catalog Number Finish Overall Length Lamp
UPX109-BL Black 9 1/2” 1-20W
UPX109-BZ Brushed Bronze 9 1/2” 1-20W
UPX109-SL Brushed Silver 9 1/2” 1-20W
UPX109-WH Designer White 9 1/2” 1-20W
UPX214-BL Black 14” 2-20W
UPX214-BZ Brushed Bronze 14” 2-20W
UPX214-SL Brushed Silver 14” 2-20W
UPX214-WH Designer White 14” 2-20W
UPX322-BL Black 22” 3-20W
UPX322-BZ Brushed Bronze 22” 3-20W
UPX322-SL Brushed Silver 22” 3-20W
UPX322-WH Designer White 22” 3-20W
UPX430-BL Black 30” 4-20W
UPX430-BZ Brushed Bronze 30” 4-20W
UPX430-SL Brushed Silver 30” 4-20W
UPX430-WH Designer White 30” 4-20W
PRO-XENON 5 MINUTE DIRECT-WIRE INSTALLATION
Step 1 Attach supplywires to rear access cover.
Step 2 Connect supplywires to fixture leadsusing push-in connectors.
Step 3 Mount fixture tocabinet bottom usingcaptive mounting screws.
Maximum cabinet bottom contact temperature: less than 60˚ C.
1"
4 1/2"
I1.5.0
LIGHTING APPLICATION DATA
FOOTCANDLES ON HORIZONTAL WORK SURFACE
Beam Width
Fixture
15"
BA C
D
12"
12" 12"
24"
Footcandles*Beam
Cat # Lamp Width A B C D
UPX109 (1) 20-watt Xenon 21” 9 31 28 35
UPX214 (2) 20-watt Xenon 23” 15 53 48 54
UPX322 (3) 20-watt Xenon 31” 24 72 65 62
UPX430 (4) 20-watt Xenon 36” 23 75 69 64
*Beam width defined as 50% of maximum footcandles
Rear wall reflectance 50%Counter Surface Reflectance 20%
UNDERCABINET LIGHTINGPRO-XENON
20W - 12-volt Xenon Lamps
UPX109, UPX214, UPX322 and UPX430
1300 S. Wolf Road • P.O. Box 5065 • Des Plaines, IL 60017-5065 • Phone (847) 827-9880 • Fax (847) 827-2925
220 Chrysler Drive • Brampton, Ontario • Canada L6S 6B6 • Phone (905) 792-7335 • Fax (905) 792-0064
Visit us at www.junolightinggroup.com Printed in U.S.A. ©2007 Juno Lighting, Inc.
ENGINEERING DATA (120V)UPF12 UPF22 UPF34 UPF46
Total input power (watts) 8.4 15.3 22.1 30.3
Total Operating AMPS .13 .23 .32 .45
Power Factor .52 .53 .57 .56
REV-5/07
PRODUCT SPECIFICATIONSLamp Latest generation of high-efficiency (HE), high colorrendering 3000K T5 tri-phosphor fluorescent lamps • 10,000 hourrated lamp life.*
Ballast State of the art 120V electronic ballast instantly starts lampand operates without flicker or hum.
Housing Extruded aluminum • Black, brushed bronze, brushedsilver or designer white finish.
Switch Convenient on/off rocker switch.
Diffuser Extruded non-yellowing clear UV/impact resistant acryliclens.
Labels UL/C-UL Listed and Energy Star compliant • Complies withCalifornia’s Title 24 energy code.
DIMENSIONS
UNDERCABINET LIGHTINGPRO-FLUORESCENT
8W, 14W, 21W & 28W
T5 HE Fluorescent Lamps
UPF12, UPF22, UPF34 and UPF46
I1.6.0
Project:
Fixture Type:
Location:
Contact/Phone:
1"
4 1/2"
PRODUCT CODES
Catalog Number Finish Overall Length Lamp
UPF12-BL Black 12 7/16” 8W T5
UPF12-BZ Brushed Bronze 12 7/16” 8W T5
UPF12-SL Brushed Silver 12 7/16” 8W T5
UPF12-WH Designer White 12 7/16” 8W T5
UPF22-BL Black 22 3/4” 14W T5 HE
UPF22-BZ Brushed Bronze 22 3/4” 14W T5 HE
UPF22-SL Brushed Silver 22 3/4” 14W T5 HE
UPF22-WH Designer White 22 3/4” 14W T5 HE
UPF34-BL Black 34 1/2” 21W T5 HE
UPF34-BZ Brushed Bronze 34 1/2” 21W T5 HE
UPF34-SL Brushed Silver 34 1/2” 21W T5 HE
UPF34-WH Designer White 34 1/2” 21W T5 HE
UPF46-BL Black 46 5/16” 28W T5 HE
UPF46-SL Brushed Silver 46 5/16” 28W T5 HE
UPF46-WH Designer White 46 5/16” 28W T5 HE
PRODUCT DESCRIPTIONPro-Fluorescent modular series luminaires offer highly efficientillumination in a shallow, easy-to-conceal profile. Ideal forundercabinet, undershelf, and task lighting, where maximum energy efficiency, long lamp life, and cool operation are desired.Pro-Fluorescent fixtures are optimized for fast permanent installation,mounting either flush to the rear backsplash or to the front lip ofcabinetry to suit project conditions and homeowner preference.
* 8W T5 tri-phosphor lamp rated at 7,500 hours.
MAXIMUM ENERGY EFFICIENCY:8 watts = 40 watts halogen14 watts = 75 watts halogen21 watts = 100 watts halogen28 watts = 150 watts halogen
INSTALLATIONUPF series fixtures optimized with a center rear wiring accesscompartment and push-in 3-wire electrical connectors for quickelectrical connection without having to open the fixture. Rear wiringaccess compartment covers provided with push-in connector for non-metallic cable and knockout for feed thru wiring capability. Multipleknockouts provided. Die-cast fitting for 3/8” flexible metal conduitsupplied in a hardware pack. Fixtures may be mounted flush to thebacksplash or up against the front lip of the cabinetry using captiveexternal mounting screws.
Portable To install as a portable fixture, use the 3-wire groundedcord & plug (ULH-CP sold separately).
Optional Direct Wire Optional direct wire module (ULH-DWMsold separately) facilitates code-compliant installation of fixture atfront edge of cabinetry. Supplied with 36” field-shortenable jumpercord to bring power to either end of the fixture.
Electrically Connecting Multiple Fixtures Up to 10 fixtures maybe electrically joined together using either the straight joinerconnector supplied with each fixture or the optional JC3 jumpercords. See accessories table for lengths and finishes.
PRO-FLUORESCENT 5 MINUTE DIRECT -WIRE INSTALLATION
Step 1 Attach supplywires to rear access cover.
Step 2 Connect supplywires to fixture leadsusing push-in connectors.
Step 3 Mount fixture tocabinet bottom usingcaptive mounting screws.
FPO
UNDERCABINET LIGHTINGPRO-FLUORESCENT
8W, 14W, 21W & 28W
T5 HE Fluorescent Lamps
UPF12, UPF22, UPF34 and UPF46
I1.6.0
FOOTCANDLES ON HORIZONTAL WORK SURFACE
Beam Width
Fixture
15"
BA C
D
12"
12" 12"
24"
*Beam width defined as 50% of maximum footcandles
Rear wall reflectance 50% 8 watts equivalent to 40 watts of halogenCounter Surface Reflectance 20% 14 watts equivalent to 75 watts of halogen
21 watts equivalent to 100 watts of halogen28 watts equivalent to 150 watts of halogen
Footcandles*Beam
Cat # Lamp Width A B C D
UPF12 8-watt T5 ”
UPF22 14-watt T5 HE ”
UPF34 21-watt T5 HE ”
UPF46 28-watt T5 HE ”
1300 S. Wolf Road • P.O. Box 5065 • Des Plaines, IL 60017-5065 • Phone (847) 827-9880 • Fax (847) 827-2925
220 Chrysler Drive • Brampton, Ontario • Canada L6S 6B6 • Phone (905) 792-7335 • Fax (905) 792-0064
Visit us at www.junolightinggroup.com Printed in U.S.A. ©2007 Juno Lighting, Inc.
ACCESSORIESCatalog No. DescriptionJC3-8-WH,-BL 8” Jumper Cord
JC3-17-WH,-BL 17” Jumper Cord
JC3-26-WH,-BL 26” Jumper Cord
ULH-CONN 3/8” Miniature Die-Cast Electrical Connector
ULH-CP-WH,-BL 3-Wire Grounded Cord & Plug
ULH-DWM-WH,-BL Direct Wire Module
LIGHTING APPLICATION DATA