content page - · pdf filecontent page 1. introduction 2. caution 3. installation 3.1....

Content Page 1. Introduction 2. Caution 3. Installation

3.1. Packing List

3.2. Placement

3.3. Connection

4. Operation 4.1. Operating Instructions

4.2. UPS Status Information

4.3. Front Panel Explanation

4.4. Rear Panel Explanation

5. Battery Usage 6. Trouble Shooting 7. Specifications 8. Technical Support

1. INTRODUCTION Thank you for buying PROLiNK Uninterruptible Power Supply (UPS) device. Our device is designed for many years of reliable usage when installed properly. Why do you need an UPS? - Among the various causes of data loss, 45% of them are due to power supply. We can make a

conclusion that if we can resolve this problem, then we can prevent half of the data loss situations that we will face.

- Temporary power supply interruption and total power blackout only make up 13% of the problems. What we are most concerned with is temporary power surge or drop, which makes up another 87% of the power supply problems that we are currently facing.

- The most crucial reason to use an UPS is not to just obtain continuous power source, but also a clean and noiseless current. Hence, one of the most important functions of UPS is to provide a stable current output.

PROLiNK Uninterruptible Power Supply (UPS) is a device that sits between a power supply (e.g. a wall outlet) and a device (e.g. a computer) to prevent undesired interference of the power source (outages, sags, surges, bad harmonics, etc.) from adversely affecting the performance of the device. PROLiNK UPS has internal batteries to guarantee that continuous power is supplied to the equipment even if the power source stops providing power. The UPS can provide power for a while, typically 20 to 50 minutes, depending on the capacity of the battery but that is often enough to ride out power glitches or short outages. The advantages are as below: 1. Computer jobs don’t stop because of power failure. 2. Users are not inconvenienced by computer shutting down. 3. Equipment does not incur the stress of another (hard) power cycle. 4. Data is not lost because a machine shut down without doing a “sync” or equivalent to flush

cached or real time data. In addition, PRO650S, PRO800S, PRO850S, PRO1200S & PRO1500S with RUPS 2000 software combinations provide the following functions: 1. Automatic shutdown of equipment during long power outages. 2. Monitoring and logging of the status of the power supply. 3. Display the Voltage/Current drawn by the equipment. 4. Display the Voltage currently on the Line. 5. Provide alarms on error conditions. 6. Review last shutdown information of Windows applications. 7. Broadcast abnormal power status to all workstations.

Certificate Number: SGPSGP001496

2. CAUTION The UPS battery has been fully charged before leaving our factory. During the shipment, some level of power may have been discharged. In order to ensure the efficiency of the UPS, please allow the UPS to charge its battery for at least 12 hours before use. Connect the UPS to a two-pole, three-wire grounding mains (AC). The AC source must be connected to appropriate branch protection (fuse or circuit breaker). Connection to any other type of AC source may result in a shock hazard and may violate your warranty claim. This UPS has an internal battery and its energy can not be de-energized by the user. The output may be energized even though when the UPS is not connected to the main AC. DO NOT install the UPS in locations where there is water or excessive humidity. DO NOT allow water or any foreign object to enter the UPS or put any objects containing liquid on or near the UPS. DO NOT remove the cover. No user serviceable parts. Refer servicing to qualified service personnel. DO NOT connect any non-computer peripherals to the UPS. The UPS is designed for use with computer loads only. To reduce the risk of overheating the UPS, avoid exposing the unit to direct sunlight. Avoid installing the unit near heat emitting appliances such as a room heater or stove.

3. INSTALLATION 3.1 Packing List Inspect the UPS upon receipt. Once the UPS is removed from its packing, it should be inspected for damage that may occur while transit. However, if damage to your UPS has occurred, kindly inform your dealer immediately for replacement. The packaging is recyclable; save it for reuse or dispose it properly. You may wish to keep the packaging box for future transportation of your UPS to another location.

Model PC650 PRO650P/B PRO650P PRO650P/Y PRO650S

Packing List

• 1 PC650 UPS

• 1 Manual • 1 Fuse • 1 Power

Cable (built-in)

• 1 PRO650P/B UPS

• 1 Manual • 1 Fuse • 1 Power

Cable (built-in)

• 1 PRO650P UPS

• 1 Manual • 1 RJ11

Cable • 1 Fuse • 1 Power

Cable (built-in)

• 1 PRO650P/Y UPS

• 1 Manual • 1 RJ11

Cable • 1 Fuse • 2 Power

Cable (UPS to load)

• 1 PRO650 UPS • 1 Manual • 1 RJ11 Cable • 1 RS232 Cable • 1 Fuse • 2 Power Cable

(UPS to load) • 1 monitoring

software

Model PRO800S PRO850S PRO1200S PRO1500S

Packing List

• 1 PRO800S UPS • 1 Manual • 1 RJ11 Cable • 1 RS232 Cable • 2 Power Cable


software



software



software



software

*Packing List is subjected to change without prior notice.

3. INSTALLATION 3.2 Placement The UPS works best in a protected environment. The location should provide adequate air flow around the unit, in an atmosphere free from excessive dust. DO NOT operate the UPS in an environment where the ambient temperature and humidity is outside or near the limits. Temperature limits: 0ºC - 40ºC (32º - 104ºF) Humidity: 0% - 95% relative humidity Select a location sturdy enough to handle the heavy weight of the UPS. 3.3 Connection

PC650 PRO650P/B PRO650P PRO650PY PRO650S

PRO800S PRO850S PRO1200S PRO1500S

3. INSTALLATION A. Connect the serial cable to the UPS and computer serial port 1. Install the RUPS2000

monitoring software to you computer. (Optional) B. Connect UPS into a two pole, three wire, grounded receptacle only 2. Avoid using

extension cords. Using the telephone cable provided, plug the cable into the telephone socket in the UPS 4. Plug other end of the telephone cable to the telephone wall socket.

C. For PRO650PY, PRO650S, PRO800S, PRO850S, PRO1200S & PRO1500S, connect

the load using the power cable provided 3. For PRO650P, PRO650P/B & PC650, connect the load using two pin or three pin power cable 3. (Note: DO NOT connect any load to your UPS until the UPS has charged its battery for 12 hours)

D. After 12 hours of charging, connect your computer and monitor to the UPS 3.

(Note: DO NOT overload your UPS. DO NOT connect a laser printer to the UPS backup socket. Laser printers draw a significantly more power than other types of equipment and may overload the UPS.)

E. DO NOT turn on the connected equipment before turning on the UPS. Turn on the UPS

first and turn on the connected equipment. This will prevent overloading of the UPS. F. To power up the UPS, press the power switch on the front panel.

4. OPERATION 4.1 Operating Instructions A. Connect the AC input power cable of your UPS to the AC Power. (See connections for

help). ‘CHARGE’ LED on the UPS front panel is lit. UPS is charging the battery. B. Plug computer and monitor to UPS sockets. (Note: Power of computer and monitor

must be less than the maximum total power of your UPS.) C. Switch on the UPS by pressing the power switch on the front panel. The ‘NORMAL’ and

‘CHARGE’ LED on the UPS front panel are lit. UPS is supplying utility power to the connected equipment and is still charging battery at the same time. If the LED is not lit, the UPS is either not turned ON or is supplying battery power.

D. When external power source fails, the UPS will power up automatically by batteries.

The ‘INVERTER’ LED is blinking and the UPS has beep sound every 5 seconds. You should save all your data and close all applications as soon as possible and turn off the UPS. If RUPS software or other compatible software is installed, your data will be saved automatically, all applications including your UPS will shut down automatically. This prevents drainage to your UPS battery and prolongs the life of your battery. This action also prevents hard disk crash situations when power failure occurs.

E. When the battery output voltage drops to a minimum, the ‘INVERTER’ LED on the UPS

front panel is continues lit while generating beeps twice every second. You should turn off the main switch of the UPS. This happens usually if no UPS management software is installed.

F. It is normal that the ‘CHARGE’ LED is on at all times. This feature prolongs the life of

the battery and prevent over drainage of the battery. 4.2 UPS Status Information

LED Indication UPS Status Buzzer Yellow

CHARGE Green

NORMAL Red

INVERTER

AC mode, Charge Battery No beeps ON OFF OFF

AC mode, UPS Normal No beeps ON ON OFF

AC abnormal UPS in battery mode Once every 5 sec OFF OFF Blinking

Battery voltage low Twice every second OFF OFF ON

Overload 4 times every 2 sec OFF OFF ON

UPS fault / Short circuit Beeps continuously OFF OFF ON

Discharge Finished No beep OFF OFF OFF

4. OPERATION 4.3 Front Panel Explanation

CHARGE LED ON when UPS is charging battery. OFF when AC is abnormal. NORMAL LED ON when UPS is running normal. OFF when UPS is off or abnormal. INVERTER LED Blinking when UPS is on battery power. ON when battery voltage low, UPS overload, short circuit or fault. OFF when UPS is running normal or UPS is off. MAIN SWITCH To control ON / OFF the UPS when utility power is normal.

4.4 Rear Panel Explanation A. AC Inlet B. Backup Outlets

C. Bypass Outlets D. Computer Interface

E. RJ11 Jacks: Modem / Fax Protection F. AC Fuse Holder (W/fuse)



5. BATTERY USAGE Please kindly refer to the below mentioned scenarios to rectify if you are facing the common issue on your battery for your UPS. 5.1 Battery - Short backup timing / Unable to backup load This scenario commonly happens when the UPS was sold after 2 to 3 months after the date of production. During this period, the batteries do not get any charging or discharging activities, thus causing it to lose its normal activity level. It causes a shorter back up time. Solution: Step 1: Before the first time usage, charge the unit up by connecting the UPS to the main power supply for at least 10 hours. Step 2: Connect a computer (if possible, connect a 200W bulb instead) by cutting off the power supply and get the UPS to work on battery mode until the UPS cut off automatically for low battery strength. Step 3: Remove the loads, charge the unit up by connecting the UPS to the main power supply for at least 10 hours. Upon completing the 3 steps, the activity of the battery will be revived.

5. BATTERY USAGE 5.2 Battery - No Backup

A. It is the same issue as scenario 1. Due to no charging and discharging activities for 2 to 3 months on the battery upon date of production will also cause the battery to lose its activity level totally in this instance.

B. The external condition of transportation is another factor that will cause the battery

to lose its activity level totally. 5.3 Battery - Short life span

A. Under the UPS usage circumstances, when inconsistent power supply is detected, the battery will be running through the charging and discharging cycles frequently and therefore, the battery life span will be shorter than expected. Our batteries are designed to have 500 cycles of 50% DOD (Depth of Discharging) according to our production standard.

B. In a high temperature working environment, battery life span will be shortened as

accordingly as well. *According to the international JISC8702-1998 standard, batteries for the UPS are designed to last for last for 200 cycles of charging and discharging only.

6. TROUBLE SHOOTING

Problem Possible Cause Solution

Normal LED does not light up when UPS is turn on. Inverter LED is red and UPS beeping.

1) AC power not on. 2) Power cable not

properly inserted. 3) Fuse blown. 4) Faulty wall socket.

1) Turn on AC power. 2) Insert power cable

properly. 3) Change the fuse. 4) Change to another wall

socket.

UPS beeps occasionally on AC mode and UPS may be heated up.

1) UPS may be overloaded.2) Unstable AC supply.

1) Check that your equipment matches the specified capacity of your UPS. Do not overload your UPS.

2) Refer to qualified electrical technician to check your AC supply and wiring.

Battery backup time is short. Long beeping sound is heard.

1) UPS may be overloaded.

2) Battery not fully charged.

3) Battery may be near the end of its lifespan.

1) Remove any non critical equipment.

2) Charge the battery for at least 8 hours before use.

3) Refer to supplier for replacement of battery (charges may be involved).

Monitoring software does not detect UPS (for PRO650S, PRO800S, PRO850S, PRO1200S & PRO1500S only)

1) Serial cable not plug in properly.

2) Comm port setting not correct.

3) Serial cable faulty.

1) Insert serial cable properly.

2) Set comm port setting to the correct port in the software setting.

3) Change serial cable.

7. SPECIFICATIONS

Model PC650 PRO650P

PRO650PY PRO650P/B

PRO650S

Capacity 650VA Voltage Range 160 – 275V 140 – 285V Frequency 40Hz - 70Hz

Input

Phase Single + GND Voltage Range 220VAC (rating) 220VAC + 17% - 22% Battery Mode 220VAC ± 15% 220VAC + 17% - 22% Frequency 50Hz ± 1Hz (Battery Mode)

Waveform Simulated Sine Wave (Battery Mode)

Sine Wave (AC Mode)

Output

Transfer Time 2ms typical Type & Number 12V7AH – 1pc 12V7.2AH – 1pc Backup Time 8 – 20 minutes depending on load

Battery

Recharge Time 90% Capacity after 8 hours

Short Circuit Protection Line mode – Fuse & software protection (CPU)

Battery mode – Software protection (CPU) Surge Protection Yes EMI/RFI & Powerline Noise Protection Yes Alarms Audible & Visual

Over Temperature Protection >75ºC Alarm will sound

>85ºC the system will shutdown

Overload Protection

Line Mode: 100-120% alarm for 3 minutes & shut down; 120-130% alarm for 30s & shut down;

>130% shuts down immediately Battery Mode: 100 – 110% gives alarm & shut down in 10s;

>110% shut down immediately

Intelligent Battery management Prevent overcharging of battery.

Protect battery and prolong battery life.

Protection/ Monitoring

Interface NA RJ11 (NA for PRO650P/B)

9P D-Type Connector NA NA AC Fault, Battery

Low, Shutdown UPS Interface

Software (optional) NA NA

Supports Netware 3.xx, Windows NT, Unix, Sun OS, HP-

UX, etc. Noise <45dB Temperature 0ºC - 40ºC Humidity 0% - 95% relative humidity Power Factor Up to 0.7

General

Built-in AVR Yes Full AVR

*Specifications are subject to change without prior notice.

7. SPECIFICATIONS

Model PRO800S PRO850S PRO1200S PRO1500S Capacity 800VA 850VA 1200VA 1500VA

Voltage Range 140 – 285VAC Frequency 40Hz - 70Hz

Input

Phase Single + GND Voltage Range 220VAC + 17% - 22% Battery Mode 220VAC + 17% - 22% Frequency 50Hz ± 1Hz (Battery Mode)


Sine Wave (AC Mode)

Output

Transfer Time 2ms typical Type & Number 12V10AH – 1pc 12V10AH – 1pc 12V7AH – 2pc 12V9AH – 2pc Backup Time 8 – 40 minutes depending on load

Battery



Battery mode – Software protection (CPU) Surge Protection Yes EMI/RFI & Powerline Noise Protection

Yes

Alarms Audible & Visual



Overload Protection



>110% shut down immediately Intelligent Battery management

Prevent overcharging of battery. Protect battery and prolong battery life.


Interface RJ11 9P D-Type Connector AC Fault, Battery Low, Shutdown UPS Interface

Software (optional) Supports Netware 3.xx, Windows NT, Unix, Sun OS, HP-UX, etc.

(except for PRO800 only) Noise <45dB Temperature 0ºC - 40ºC Humidity 0% - 95% relative humidity Power Factor Up to 0.7

General

Built-in AVR Full AVR

*Specifications are subject to change without prior notice.

8. TECHNICAL SUPPORT FREE TECHNICAL SUPPORT HOTLINE: Mon to Fri: 9am - 6pm (Closed on Saturdays, Sundays & Public Holidays) Singapore : (65) 6357 0666 Malaysia : (60) 3 8023 9151 Indonesia : (62) 21 3483 1717 WALK-IN: Mon to Fri: 9am - 6pm (Closed on Saturdays, Sundays & Public Holidays) Singapore FIDA INTERNATIONAL (S) PTE LTD Blk 16 Kallang Place #06-02 Kallang Basin Industrial Estate Singapore 339156 Malaysia FIDA SYSTEMS (M) SDN BHD 29 USJ 1/31, 47600 Subang Jaya Selangor, Darul Ehsan, Malaysia Indonesia PROLiNK INDONESIA Jl. Cideng Barat No. 79, Jakarta Pusat 10150, Indonesia ONLINE TECHNICAL SUPPORT: [email protected]

ISI Buku 1. Pendahuluan 2. Perhatian 3. Instalasi

3.1. Isi Kemasan

3.2. Penempatan

3.3. Koneksi

4. Penggunaan 4.1. Instruksi Penggunaan

4.2. Informasi Status UPS

4.3. Penjelasan Panel Depan

4.4. Penjelasan Panel Belakang

5. Penggunaan Baterai 6. Permasalahan dan Solusi 7. Spesifikasi Produk 8. Teknikal bantuan

1. PENDAHULUAN Terima kasih telah membeli PROLiNK Uninterruptible Power Supply (UPS). Produk ini di design untuk penggunaan dalam waktu yang lama apabila digunakan dengan benar. Mengapa UPS dibutuhkan? - Dalam beberapa hal penyebab kehilangan data, 45% berasal dari listrik. Kita bisa

membuat suatu kesimpulan bahwa jika kita dapat memecahkan masalah ini, kita dapat mencegah sebagian dari penyebab kerugian data (Data Loss).

- Padamnya arus listrik dan gangguan blackout hanya hanya 13% dari total permasalahan dari listrik. Sisanya 87% adalah berasal dari voltase listrik yang tidak stabil.

- Alasan yang paling tepat untuk menggunakan UPS adalah bisa menstabilkan listrik dan yang paling penting adalah pada saat listrik mati secara tiba-tiba, komputer tetap akan terselamatkan karena UPS tetap akan menyediakan listrik selama waktu tertentu.

PROLiNK Uninterruptible Power Supply (UPS) adalah suatu alat yang berada diantara listrik dari PLN dan Komputer dimana alat ini dapat mencegah perubahan dari listrik yang terjadi secara tiba-tiba. PROLiNK UPS mempunyai baterei internal untuk menjamin listrik yang berlanjut pada saat sumber listrik dari PLN padam. Tentu saja UPS dapat menyediakan listrik untuk beberapa waktu, secara khas beberapa menit, tetapi itu sudah cukup untuk mempertahankan data kita yang penting. Keuntungan : 1. Pekerjaan komputer tidak akan terhenti apabila listrik padam. 2. Para pengguna akan sempat mematikan komputer secara normal. 3. Peralatan akan lebih tahan lama dari kerusakan yang disebabkan oleh listrik. 4. Data tidak akan hilang apabila listrik padam secara tiba-tiba. Sebagai tambahan, PRO650S, PRO800S, PRO850S, PRO1200S dan PRO1500S dilengkapi dengan software RUPS 2000 yang menyediakan fungsi sebagai berikut : 1. Dapat menshutdown komputer secara otomatis selama listrik padam. 2. Dapat memonitoring status dari UPS dan Listrik yang ada. 3. Dapat melihat kapasitas beban yang ada pada saat itu. 4. Dapat melihat voltase yang ada pada saat itu. 5. Tersedia alarm untuk memberikan tanda pada kondisi tertentu. 6. Mempunyai log yang dapat memberikan informasi shutdown terhadap aplikasi. 7. Memberikan peringatan kepada kita apabila ada status yang tidak normal.

Certificate Number: SGPSGP001496

2. PERHATIAN Baterei UPS sudah diisi penuh sebelum keluar dari pabrik. Selama pengiriman, kapasitas dari isi baterei akan berkurang. Untuk memastikan efisiensi dari UPS, sebaiknya baterei diisi kembali sebelum digunakan selama 12 jam. Hubungkan UPS ke pusat listrik dengan menggunakan kabel 3 pin (berikut grounding). Grounding ini sangat berguna untuk memproteksi peralatan kita dari petir. UPS ini mempunyai baterei internal dan energi nya tidak bisa dibuang. Output dari UPS sendiri akan mengeluarkan arus listrik walaupun UPS tidak dihubungkan langsung ke aliran JANGAN meletakan UPS di dekat daerah yang lembab atau basah. JANGAN biarkan air atau benda asing lain nya masuk kedalam UPS. JANGAN membuka casing UPS atau melakukan reparasi sendiri. JANGAN gunakan UPS ini ke peralatan yang bukan peralatan komputer. UPS ini hanya di rancang untuk digunakan oleh peralatan komputer saja. Untuk mengurangi resiko panas yang berlebihan dari UPS, jangan meletakan UPS yang langsung terkena sinar matahari atau hindari peletakaan yang dekat dengan peralatan yang mengeluarkan panas.

3. INSTALASI 3.1 Isi Kemasan Perhatikan isi UPS pada saat membeli. Jika ditemukan UPS dalam keadaan cacat fisik, segeralah untuk menukarkannya dengan yang baru. Kotak UPS dapat di daur ulang, bisa disimpan atau dibuang, namun ada baik nya kalau kotak disimpan untuk dapat digunakan kembali.

Model PC650 PRO650P/B PRO650P PRO650P/Y PRO650S

Isi Kemasan

• 1 PC650 UPS

• 1 Buku Manual

• 1 Sekering • 1 Kabel

Power (built-in)

• 1 PRO650P/B UPS

• 1 Buku Manual


Power (built-in)

• 1 PRO650P UPS

• 1 Buku Manual

• 1 Kabel RJ11


Power (built-in)

• 1 PRO650P/Y UPS

• 1 Buku Manual

• 1 Kabel RJ11


Power (ke peralatan)

• 1 PRO650 UPS • 1 Buku Manual • 1 Kabel RJ11 • 1 Kabel RS232 • 1 Sekering • 2 Kabel Power

(ke peralatan) • 1 monitoring

software

Model PRO800S PRO850S PRO1200S PRO1500S

Isi Kemasan

• 1 PRO800S UPS • 1 Buku Manual • 1 Kabel RJ11 • 1 Kabel RS232 • 2 Kabel Power (ke

peralatan) • 1 monitoring

software



software



software



software

*Isi Kemasan dapat berubah sewaktu-waktu tanpa pemberitahuan terlebih dahulu.

3. INSTALASI 3.2 Penempatan UPS dapat bekerja dengan baik apabila diletakan pada tempat yang terjaga dengan baik. Dimana lokasinya terdapat sirkulasi udara yang baik dan jauh dari debu. JANGAN menggunakan UPS ditempat yang bertemperatur tinggi atau mendekati batas dari kelembaban nya. Batas Temperatur : 0ºC - 40ºC (32º - 104ºF) Kelembaban: 0% - 95% kelembaban relative. Pilihlah tempat yang sesuai dengan ukuran dan berat dari UPS yang digunakan. 3.3 Koneksi



3. INSTALASI A. Sambungkan kabel serial dari UPS ke Komputer serial port 1. Install software

RUPS2000 ke komputer anda. (Optional) B. Sambungkan UPS ke sumber listrik yang mempunyai grounding yang baik 2. Jangan

menggunakan sambungan kabel listrik. Dengan menggunakan kabel telepon yang telah disediakan, sambungkan kabel tersebut ke soket telepon yang ada pada UPS 4 dan sambungkan sisi lain nya ke sumber line telepon anda.

C. Untuk UPS jenis PRO650PY, PRO650S, PRO850S, PRO1200S & PRO1500S,

sambungkan output UPS ke peralatan komputer anda dengan menggunakan kabel power yang sudah disediakan 3. Untuk UPS jenis PRO650P, PRO650P/B & PC650, sambungkan output UPS dengan menggunakan kabel power 2 pin/3 pin 3. (Note: JANGAN dulu menggunakan UPS anda sampai baterai dari UPS anda sudah di charge selama kurang lebih 12 jam).

D. Setelah 12 jam, sambungkan lah komputer anda ke UPS 3. (Note: JANGAN gunakan

peralatan yang melebihi dari kemampuan UPS anda. seperti laser printer, karena Laser printers membutuhkan daya yang sangat besar dari peralatan komputer anda yang lainnya).

E. JANGAN menghidupkan UPS anda sebelum semua peralatan sudah tersambung ke

UPS. Hidupkanlah terlebih dahulu UPS anda, baru kemudian di susul dengan komputer anda. Ini akan menghindari terjadinya overloading pada UPS

F. Untuk menghidupkan UPS, tekan tombol power pada panel depan UPS.

4. PENGGUNAAN 4.1 Instruksi Penggunaan G. Sambungkan kabel power dari UPS ke sumber listrik (PLN). (Lihat bagian Koneksi

untuk bantuan). Lampu ‘CHARGE’ akan menyala. Artinya UPS sedang melakukan charging ke baterai.

H. Sambungkan komputer dan monitor anda ke output UPS. (Note: Total daya dari

komputer dan monitor harus lebih kecil dari kemampuan output daya maximum dari UPS anda.)

I. Nyalakan UPS dengan menekan tombol power yang ada pada panel depan. Lampu

‘NORMAL’ dan ‘CHARGE’ akan menyala. Artinya UPS bekerja dengan menggunakan listrik PLN dan tetap melakukan charging ke baterai dalam waktu yang bersamaan.

J. Ketika sumber listrik padam, UPS akan bekerja secara otomatis dengan menggunakan

baterai. Lampu ‘INVERTER’ akan berkedip dan diikuti dengan suara beep di setiap 5 detik. Saat ini anda harus menyimpan seluruh data anda dan matikan UPS secara manual. Jika software RUPS2000 tersedia, maka data anda secara otomatis akan tersimpan lalu komputer dan UPS anda juga akan mati secara otomatis. Hal ini dilakukan untuk memperpanjang umur baterai anda. Juga untuk menghindari kerusakan hardisk anda dari listrik yang padam secara tiba-tiba.

K. Ketika output dari baterai melemah, lampu ‘INVERTER’ akan terus berkedip dan diikuti

dengan suara beep 2 kali disetiap detik. Anda secepatnya harus mematikan UPS secara manual. Ini sering terjadi untuk UPS jenis tanpa software monitoring.

L. Normal apabila lampu ‘CHARGE’ menyala terus. UPS ini mempunyai fitur untuk me

manage baterai anda. 4.2 Informasi Status UPS

Indikator Lampu Status UPS Buzzer Kuning

CHARGE Hijau

NORMAL Merah

INVERTER

Mode AC, Baterai Charge Tidak ada Bunyi HIDUP MATI MATI

Mode AC, UPS Normal Tidak ada Bunyi HIDUP HIDUP MATI

Sumber Listrik Padam, dan UPS bekerja dengan

baterai

Bunyi beep setiap 5 detik MATI MATI Berkedip

Output Baterai melemah Bunyi beep 2 kali setiap detik MATI MATI HIDUP

Overload Bunyi beep 4 kali setiap 2 detik MATI MATI HIDUP

UPS bermasalah Bunyi beep panjang MATI MATI HIDUP

Proses Discharge Selesai Tidak ada Bunyi MATI MATI MATI

4. PENGGUNAAN 4.3 Penjelasan Panel Depan

Lampu CHARGE : HIDUP ketika UPS sedang melakukan proses charging. MATI ketika sumber listrik (PLN) padam. Lampu NORMAL : HIDUP ketika UPS bekerja normal. MATI ketika UPS mati atau tidak normal. Lampu INVERTER : Berkedip ketika UPS bekerja dengan baterai. HIDUP ketika baterai melemah, UPS overload, atau bermasalah. MATI ketika UPS bekerja normal atau UPS mati. Main Switch Untuk mengontrol UPS HIDUP / MATI.

4.4 Penjelasan Panel Belakang A. AC Inlet B. Backup Outlets

C. Bypass Outlets D. Computer Interface

E. RJ11 Jacks: Modem / Fax Protection F. AC Fuse Holder (W/fuse)



5. PENGGUNAAN BATERAI Hal yang perlu di perhatikan jika anda menemukan masalah pada baterai anda. 5.1 Baterai - Waktu backup singkat / Tidak dapat mem backup beban Hal ini biasa terjadi setelah UPS tidak digunakan setelah 2 hingga 3 bulan, setelah tanggal produksi. Hal ini di sebabkan karena selama periode ini, baterai tidak mengalami aktifitas dari proses pengisian dan pengosongan, sehingga menyebabkan pada saat aktifitas penggunan biasa. Waktu backup baterai menjadi lebih singkat. Solusi: langkah 1: Sebelum di gunakan untuk pemakain pertama, lakukan proses pengisian pada baterai sedikitnya 10 jam. langkah 2: Sambungkan dengan komputer (jika dimungkinkan, berikan beban lampu sebesar 200W) lalu cabut sumber listrik (PLN) dan biarkan UPS berkerja melalui baterai hingga UPS secara automatis mati karena output baterai sudah habis/kosong. langkah 3: Setelah UPS mati, cabut beban lampu tadi, lalu kemudian lakukan aktifitas proses pengisian sedikitnya 10 jam. Setelah melakukan semua ke 3 langkah tadi, maka baterai sudah dapat berkerja normal kembali.

5. PENGGUNAAN BATERAI 5.2 Baterai – Tidak dapat membackup

A. Hal ini sama dengan tahapan seperti yang telah di sebutkan di atas. dalam kaitannya dengan tidak adanya aktifitas proses pengisian dan pengosongan baterai selama 2 hingga 3 bulan sejak baterai di produksi. Hal ini akan menyebabkan battery tidak dapat bekerja secara maksimal membackup beban yang ada.

B. Transportasi juga merupakan salah satu faktor lainnya yang dapat menyebabkan

baterai tidak dapat bekerja secara maksimal membackup beban yang ada. 5.3 Baterai – Waktu pemakaian baterai yang pendek

A. Pada saat UPS mendeteksi adanya ketidak stabilan aliran listrik yang masuk, baterai akan berkerja dengan melakukan pengisian dan pengosongan secara periodik di setiap kali aliran listrik naik dan turun, hal ini dapat menyebabkan umur baterai menjadi lebih singkat dari kondisi yang seharusnya, Baterai yang kami gunakan, di rancang untuk dapat bekerja 500 cycle dari kondisi proses pengisian dan pengosongan, maka ini berarti baterai mengalami 50% DOD (Depth of Discharging) melebihi dari standart produksi yang di tentukan.

B. Pada suhu tinggi di lingkungan sekitar, hal ini juga dapat menyebabkan umur

baterai akan menjadi lebih pendek. *menurut standart internasional JISC8702-1998, sebuah baterai didisain harus mampu sedikitnya 200 cycle dalam proses pengisian dan pengosongan.

6. PERMASALAHAN DAN SOLUSI

Masalah Possible Cause Solution

Lampu LED tidak menyala pada saat UPS dihidupkan. Lampu INVERTER berkedip.

1) Tombol on/off tidak

pada posisi menyala 2) Kabel input listrik

tidak terpasang dengan benar.

3) Sekering terputus. 4) Kerusakan di soket

koneksi listrik pada dinding.

1) Hidupkan UPS dengan menekan tombol pada UPS.

2) Pastikan pemasangan kabel power listrik sudah terpasang dengan benar.

3) Ganti sekering yang putus.

4) Ganti ke soket listrik yang lainnya.

Terdengar bunyi beep pada kondisi UPS terhubung listrik (PLN) atau UPS mengalami panas yang berlebihan.

1) Beban UPS yang mungkin berlebih.

2) Listrik yang kurang stabil.

1) Periksa semua peralatan yang terhubungkan ke UPS. Pastikan beban tidak melebihi kapasitas dari UPS.

2) Mengacu pada teknisi yang ahli dalam bidang kelistrikan untuk memeriksa soket dan kabel listrik

Waktu backup baterai yang pendek. Mengeluarkan bunyi beep.

1) Beban UPS yang mungkin berlebihan

2) Battery tidak di isi dengan penuh.

3) Battery mungkin sudah dekat dengan masa pakainya

1) Lepaskan barang-barang yang tidak terlalu di perlukan dari UPS.

2) Lakukan pengisian battery sedikitnya lebih dari 8 jam sebelum di gunakan

3) Bawa UPS pada supplier untuk mengganti battery (dengan pergantian battery mungkin dapat membantu)

Software monitoring tidak dapat mendeteksi UPS yang terpasang (hanya untuk type PRO650S, PRO800S, PRO850S, PRO1200S & PRO1500S)

1) Kabel serial tidak terpasang dengan benar

2) Terdapat kesalahan dalam settingan pada Com port

3) Karusakan pada kabel serial

1) Hubungkan serial kabel secara benar.

2) Pastikan settingan pada com port sudah sesuai dengan settingan dari software yang di sertakan.

3) Ganti kabel serial

7. SPESIFIKASI PRODUK

Model PC650 PRO650P

PRO650PY PRO650P/B

PRO650S

Capacity 650VA Voltage Range 160 – 275V 140 – 285V Frequency 40Hz - 70Hz

Input

Phase Single + GND Voltage Range 220VAC (rating) 220VAC + 17% - 22% Battery Mode 220VAC ± 15% 220VAC + 17% - 22% Frequency 50Hz ± 1Hz (Battery Mode)


Sine Wave (AC Mode)

Output

Transfer Time 2ms typical Type & Number 12V7AH – 1pc 12V7.2AH – 1pc Backup Time 8 – 20 minutes depending on load

Battery



Battery mode – Software protection (CPU) Surge Protection Yes EMI/RFI & Powerline Noise Protection Yes Alarms Audible & Visual



Overload Protection



>110% shut down immediately

Intelligent Battery management Prevent overcharging of battery.

Protect battery and prolong battery life.


Interface NA RJ11 (NA for PRO650P/B)

9P D-Type Connector NA NA AC Fault, Battery

Low, Shutdown UPS Interface

Software (optional) NA NA

Supports Netware 3.xx, Windows NT, Unix, Sun OS, HP-

UX, etc. Noise <45dB Temperature 0ºC - 40ºC Humidity 0% - 95% relative humidity Power Factor Up to 0.7

General

Built-in AVR Yes Full AVR

*Spesifikasi produk dapat berubah sewaktu-waktu tanpa adanya pemberitahuan terlebih dahulu.

7. SPESIFIKASI PRODUK

Model PRO800S PRO850S PRO1200S PRO1500S Capacity 800VA 850VA 1200VA 1500VA

Voltage Range 140 – 285VAC Frequency 40Hz - 70Hz

Input

Phase Single + GND Voltage Range 220VAC + 17% - 22% Battery Mode 220VAC + 17% - 22% Frequency 50Hz ± 1Hz (Battery Mode)


Sine Wave (AC Mode)

Output

Transfer Time 2ms typical Type & Number 12V10AH – 1pc 12V10AH – 1pc 12V7AH – 2pc 12V9AH – 2pc Backup Time 8 – 40 minutes depending on load

Battery



Battery mode – Software protection (CPU) Surge Protection Yes EMI/RFI & Powerline Noise Protection

Yes

Alarms Audible & Visual



Overload Protection



>110% shut down immediately Intelligent Battery management

Prevent overcharging of battery. Protect battery and prolong battery life.


Interface RJ11 9P D-Type Connector AC Fault, Battery Low, Shutdown UPS Interface

Software (optional) Supports Netware 3.xx, Windows NT, Unix, Sun OS, HP-UX, etc.

(except for PRO800 only) Noise <45dB Temperature 0ºC - 40ºC Humidity 0% - 95% relative humidity Power Factor Up to 0.7

General

Built-in AVR Full AVR

*Spesifikasi produk dapat berubah sewaktu-waktu tanpa adanya pemberitahuan terlebih dahulu.

8. TEKNIKAL BANTUAN TALIAN UNTUK BANTUAN TEKNIKAL: Isnin hingga Jumaat: 9am – 6pm (Tutup pada hari Sabtu, Ahad dan Hari Cuti Awam) Singapura : (65) 6357 0666 Malaysia : (60) 3 8023 9151 Indonesia : (62) 21 3483 1717 KEMASUKAN: Talian Untuk Bantuan Teknikal: Isnin hingga Jumaat: 9am – 6pm (Tutup pada hari Sabtu, Ahad dan Hari Cuti Awam) Singapura FIDA INTERNATIONAL (S) PTE LTD Blk 16 Kallang Place #06-02 Kallang Basin Industrial Estate Singapore 339156 Malaysia FIDA SYSTEMS (M) SDN BHD 29 USJ 1/31, 47600 Subang Jaya Selangor, Darul Ehsan, Malaysia Indonesia PROLiNK INDONESIA Jl. Cideng Barat No. 79, Jakarta Pusat 10150, Indonesia BANTUAN TEKNIKAL: [email protected]

Blk 16 Kallang Place #06-02 Singapore 339156

Register Online For Your Product Warranty www.prolink2u.com

SINGAPORE FIDA INTERNATIONAL (S) PTE LTD Block 16 Kallang Place, #06-02 Kallang Basin Industrial Estate, Singapore 339156. Tel : (65) 6357 0668 Email : [email protected] MALAYSIA FIDA SYSTEMS (M) SDN BHD 29 Jalan USJ 1/31, 47600 Subang Jaya, Selangor Darul Ehsan, Malaysia. Tel : (60) 3 8024 9151 Email : [email protected] INDONESIA PROLiNK INDONESIA Jl. Cideng Barat No. 79, Jakarta Pusat 10150, Indonesia. Tel : (62) 21 3483 1777 Email : [email protected]

PROLiNK is a trademark of Fida International (S) Pte Ltd and is manufactured under its authority. All other brands, products, services, logos and company names mentioned herein are trademarks of their respective owners. All specifications, designs and contents are subject to changes without prior notice. © Copyright 2009. PROLiNK all rights reserved.

content page - · pdf filecontent page 1. introduction 2. caution 3. installation 3.1....

Documents