control and management presentation

8/16/2019 Control and Management Presentation

1/41

Control & Management

Solutions


2/41

There are various ways to control differentequipment types and site conditions:

• Dry controls• Measurements• Environment• Sensors / detectors•

Communication• UPS and DC Systems

Control & Management


3/41

Equipment control

Air Conditioners

Older telecomequipment

Manufacturing

Access

Generators


4/41

• Check status and control operation of air conditioners.• Control industrial or custom process, like switching

cooling fan on when internal street cabinettemperature gets too high.

•

Control older UPS and DC systems through their drycontact connection controls.• Check and operate generators using it’s control panel. • Access (barrier, gate, door) control via SMS or calls,

with access database.

• Remote control of all equipment by Internet or SMS.• Automatic response actions for situation changes.• Notifications on e-mail and/or SMS about all

events.

Equipment Control


5/41

Electricity measurement

Special low voltage sensors

Current

FrequencyKWH meters

Voltage


6/41

Electricity measurement

Measurement

Without adaptor

With adaptor

Adaptor type

AC voltage (V)

0÷40 0÷450 Transducer

DC voltage (V) ± 0÷60 ± 0÷450 Transducer

AC current (A)

0÷100 Current transformer

DC current 60mV measurement DC Shunt

DC current (A) 0÷100 Hall sensor

Frequency (Hz)

45÷65 (up to 40v)

45÷65

Transducer

Various electrical measurements are supported. transducersless-High voltages require external transformer

that lower high voltages to


7/41

Environment and more

Temperature

Fuel level

Humidity

Gas


8/41

Environment & More

Humidity and temperature sensors can be installed andmonitored.Thresholds and hysteresis levels for alarms areconfigurable.Wide list of generic sensors can be connected andmonitored as well, operating at 0÷5Vdc or 0÷60mVdc.Generic sensors include gas, fluid level in a tank, liquidflow, lighting, process control and more.


9/41

Sensors & Detectors

Smoke detectors Water detectors

Motion detectors Door/window detectors

Process micro switch control


10/41

Sensors & Detectors

Security alarms can be sent based on events generated by smoke,water, flame, intruder, and motion detectors.Any detector with dry contact indication can be connected.Auxiliary operation voltage might be required by some types ofdetectors.


11/41

IT Control IT Control

ServersSwitches /

Routers

Workstations

Network printers


12/41

• Servers, workstations, routers, switches, networkprinters, hardware firewalls and spam filters, and anyother device with Ethernet connection can all becontrolled by the IT Control feature.

• Devices supporting SNMP (Simple NetworkManagement Protocol) provide various statusinformation: CPU load, hard drive space, physical andvirtual memory, installed software, and list of runningprocesses.

• Detailed information can be viewed remotely.• Windows servers shutdown is integrated through free

client software.• Manual and automatic LAN wakeup function is

implemented.

IT Control


13/41

UPS & DC Systems

Other manufacturer’s UPS

PS1006 DC System

Small UPS systems

µPS-SP Industrial UPS

Power+ Modular UPS


14/41

UPS & DC Systems

Gamatronic UPS and DC Systems can be monitoredthrough RS-232 serial communication port.Notifications and alarms can be sent on SMS, e-mail, drycontacts.Full information about UPS status and operation on the

web interface.Remote control actions (shutdown, load on bypass…).Computers shutdown due to power failure or low batterycondition.Computer wake up after power failure.Some other manufacturer’s UPS and DC Systems

are supported.


15/41

Practical Applications theDatacenter

Water was detected under the raised floor in unmannedcomputer room by water leakage detector. What can beautomatically done to minimize the damage? 1. Send SMS notification to relevant people

2. Send shutdown signal to all servers3. Operate local audio alarm by means of dry contact4. Wait for emergency service


16/41

Practical ApplicationsUnmanned Site

Thousand of cellular sites consume power, need securitysystem and environmental controls. Only for knowingelectricity consumption, personnel is being sent to everysite once a month. How to minimize overall cost?

1. Management and Control unit is installed2. All site parameters are monitored and reported3. Emergency actions are programmed4. Site access can be controlled5. KWH meters power consumption is

accessible remotely


17/41

Practical Applications Accessto Control

Medium sized company has about 200 employees entering theunderground parking every day. Electronic barrier controls entry. Howto automate entry process without implementing expensive tagsecurity system?

1. C&M unit is installed inside the barrier mechanism2. Build internal database with employee’s phone numbers 3. In front of the barrier, they just dial in from the mobile4. The gate will open by recognizing their phone number5. The phone call will not be answered

by the unit, no cost since there wasno conversation


18/41

Gamatronic C& M Solutions:WING

WING is a simple cellular communication device. Itis being installed on UPS and DC systems, andprovides SMS alarms to the end user or controlcenters. On Power+ UPS, for example, the unit’snetwork board will automatically detect and startusing the newly attached cellular modem forcommunication. Recipient's phone numbers areeasily added through the user friendly web interface.


19/41

Gamatronic C&M Solutions:WING

12vDC operating voltage can be taken either from Power+ System Controllerauxiliary voltage connector for battery backup, or from a provided 12v AC/DCadaptor. SIM card is required for operation, quad-band GSM modem providesworldwide cell network coverage.

Supported products: DC Power Systems: PS1006, PS2012, 1UDC+ UPS Systems: µPS-SP, MST, Power+, Power+ SA

SIM card is required

for GSM communication,

such as SMS or GPRS


20/41

Gamatronic C&M Solutions:G4

G4 is a sophisticated control and management solution that includesembedded software with web interface and wide list of equipmentmonitoring options.

• It can be installed as an added value for UPS or DC system, or just as a stand-alonesite controller.

• Fully configurable and programmable interface makes this unit highly flexible to fitany site and application.

• Available in stand-alone or 19” rack mountable versions.


21/41


Front panel includes:

Network connection

Extra RS-232 output (usually disabled)IndicatorsSIM card slotReset buttons


22/41


Rear panel 12vDC connection includes:

Dry input contacts

Changeover dry output contactsTemperature sensors connector (adaptor board included)RS-232 serial communication portCellular antenna connection

Temperature

sensor:


23/41


G4 operates with dry contacts and temperaturemeasurements for environment and equipmentcontrol. It can also communicate with a power devicethrough RS232 serial communication port, and monitor

computer equipment via the IT Control (Ethernetconnection).

Connection Amount Remark

Dry inputs 8 N.O. / N.C. programmable

Dry outputs 4 Changeover (N.O. / COM. / N.C.)Temperature 5 One sensor is included with the unit

RS-232 1 UPS / DC system comms., several protocols

Ethernet 1 Web / SNMP communication + IT Control


24/41

Gamatronic C&M Solutions:G4 Web Interface

Configuration and programming of G4 is performed through webinterface, no software is required:


25/41


IT Control monitors any equipment with IP address, andshows verbose information for SNMP-enabled devices:


26/41


Serial device configuration helps to access all supportedtypes of equipment with auto-detect feature:


27/41


SMS notifications will be sent to specified cellularnumbers, and according to the event type:


28/41


The G4 will also accept external control through SMSmessaging and reply to the initiator:


29/41

Gamatronic C&M Solutions

G-Eye is the fully featured Site Manager. Monitoring and control optionsare extended compared with the G4. It also shows great emergency performance with it’s internal backup battery and front panel LCD.

Complete site monitoring includes more features, like KWH meters andpower measurements.

Additional environmental control features include more options.19” design to suit standard mounting equipment.


30/41


Connection Amount Remark

Dry inputs 32 NO/NC programmable

Dry outputs 16 Changeover

Temperature 4 One sensor includedRS-232 1 UPS / DC system monitoring

Ethernet 1 Communication + IT Control

AC or DC volts / AC or DC amps 12 Transducer required > 40v/60vDC

Isolated DC volts / DC amps 4 Up to 60v or 60mV shunt

Frequency 2 Transducer required > 40v

kWH metering 2 Pulse reading only

Humidity 2 Precise 0÷100% measurement

Flood (with aux. voltage) 1 Special sensors available

Liquid level 1 Various sensors exist on market


31/41

Gamatronic C&M Solutions Servers

Telecom equipmentAir conditioners

UPS

DC Power

Measurements

Fuel level

Diesel generators

Safety kWH


32/41


• With the G-Eye on the site, you receive the mostcomplete data including live electricity measurements.

• All this without unnecessary complications and costs

involved in installation and maintenance.• All programming and fine tuning are performed

remotely, without loosing the control even for aminute.

• Universal input power and the backup battery features

will ensure that appropriate procedures will beexecuted and alarms sent even during total siteblackout.

• Security is maintained by password protection on theweb interface. No actions can be carried out withoutauthentication.


33/41

Gamatronic C&M Solutions:G-Eye Web Interface

G-Eye electricity measurements are highlyconfigurable, all of them include high/low alarms andhysteresis.


34/41


All connected measurements must be calibrated carefully uponinstallation in order to achieve correct figures.


35/41


Internal log of events can be downloaded in MS Excelformat for additional processing.


36/41

Gamatronic C&M Solutions: G-Eye Web

Interface

Internal log of events can be downloaded in MS Excelformat for additional processing.


37/41

Gamatronic C&M Solutions:Management Software

Control centers require global centralized control overlarge amount of units and/or sites. GEMSi software isdesigned for both large control centers and compact, in-company monitoring.

GamatronicElementManagementSystem

innovated

i l i


38/41


• Secure user-controlled interface with action loggingallows direct access to regions and sites, either oncountry/county or factory/room level.

• All Gamatronic and supported non-Gamatronic units canbe put on one screen.

• Alarms pop up and logged for all units, with user-defined severity.• Data logging is supported for detailed tracking of

problematic site conditions.• Unlimited event logging.•

Powerful, fully configurable reports generation supportsexcel output format.• Database backup/restore feature.• Includes all Gamatronic communication software.

G i C& S l i


39/41


Easy map oriented navigation makes control simple andintuitive.

G i C&M S l i


40/41


Built in browser shows real-time data within GEMSi,

without the need to open external windows.


41/41

Gamatronic hardware and software Control & Management solutionskeep you confident and your site safe wherever you are at all times.

control and management presentation

Documents