corrientes en los momentos de conexión

8/8/2019 Corrientes en los momentos de conexin

1/12

http://www.epcos.com

Damping of Inrush Currentin Low-Voltage PFC EquipmentLow-Voltage PFC

Application Note 2001


2/122 EPCOS AG

Power Quality

Contents

General 3

The risks of high inrush current 4

Single capacitor connection, inrush current calculation 6

Parallel capacitor connection, inrush current calculation 7

Various solutions for limiting inrush current serial aircoils 7

Detuning reactors, connection cable selection 8

Capacitor contactors with damping resistorsFunctionality / comparison 9

Comparison 10

Capacitor bank switching under various conditions 11


3/123EPCOS AG

Damping of Inrush Currentin Low-Voltage PFC EquipmentGeneral

The market trend to reduce lossesin modern low-voltage power-factor-correction capacitors (LV-PFCs)and the requirement for highoutput density result in reducedohmic resistance in PFC capacitors.Especially the switching of capa-citors in parallel to others of thebank, already energized, causesextremely high inrush current,up to 200 times the rated current,and limited only by the ohmicresistance of the capacitor itself.According to the formula ( Eq1),such a capacitors AC resistance isvery low and thus contributes tohigh inrush current.

LV-PFC capacitor bank

Inrush current (pulse) is a factor of:

a Remaining capacitor voltagedue to fast switching in auto-matic capacitor banks

a Shortcircuit power of supplytransformer

a Output of capacitor switchedin parallel to others alreadyenergized

aFault level of supply network

a Output of capacitors alreadyenergized

a Ohmic resistance of capacitoritself and distribution switchgear, connection cables or con-ductors

KLK1709-W

25kVAr

25kVAr

25kVAr

25kVAr

25kVAr

25kVAr

12.5

kVAr

25kVAr

M3~

187,5 kVAr

Automatic capacitor bankwith 6 capacitors in parallel

High inrush current for grid,high balancing currents for capacitors

xc =1

2**f*c

Eq1:

Switching operation: f xc0 200 * Ir


4/124 EPCOS AG

Inrush Current by ConnectingCapacitor in Parallel (Energization)

The risks of high inrush current

Connecting LV-PFC capacitors with-out damping to an AC grid stressesthe capacitor like a shortcircuit.To avoid negative effects and toimprove a capacitors life time, ade-quate damping of inrush current ishighly recommended.

Influence of high inrush currentand resulting distortion:

a High stress on the capacitor reduced lifetime

a Welding or fast wearing out ofthe main contacts of contactors

a Negative effects on powerquality (eg.voltage transients)

a Overvoltage: insulation problems

defects of electronic equipment

production stop

a Undervoltage/voltage zerocrossing measurement failure problems with numerical

control equipment

production stop due tocomputer failure

a High cost of maintenance andproduction standstill

73.2 73.8 74.5 75.1 75.7 76.3 77.0 77.6 t (ms)

4000

3000

2000

1000

0

-1000

-2000

-3000

Current(A)

Capacitor inrush current

ONOFF 5th capacitor connected

Peak current occurrence

i = 157* IN = 157*21 = 3300 Ai

i

Capacitor connection:IN

=rated current= 21A


5/12

0 10 20 30 40 50 60 70 80 90 100t (ms)

1500

1000

500

0

-500

-1000

-1500

Voltage(V)

1st step on 2nd step on 3rd step on 4th step on 5th step on 6th step on

1

1

High peak voltage (transients) occurrence

1 12

2

> UINS risk of shortcircuit 0 V results in wrong measurementscausing control failures

1

2

5EPCOS AG

Inrush Measurementof Capacitor Steps

Switching of power factor correc-tion (PFC) capacitors is not onlyrelated to high currents but alsoto high voltage transients (ref.capacitor switching-on steps 16),causing degradation ofpowerquality, if the negative influenceis not prevented by damping.

Capacitor sample,contact surface damagedby high inrush currents

High inrush current occurrencesdue to insufficient dampingcaused high electromechanicalforces within the capacitor. Espe-cially the contact area betweenelectrodes (windings) and themetal-spray layer was extremelystressed by high current forces.

The example shows that a fractionof metal-spray layer separatedfrom the windings. Even the MKKcapacitor with excellent pulsecurrent capability and enhancedcontactability due to wavy cut andheavy edge design of the filmshows that extensive power cancause failures.

Voltage at 0.69 kV - busbar

PFC capacitor cascade connection:High voltage transients occurrence due to no damping

Example

Metal-spray layerseparated from thecapacitor windings


6/126 EPCOS AG

Inrush Current Calculation

KLK1706-7

Grid

L 3

L

L 2

1UN

Connecting a single capacitor

Circuit and formula

Terms

Result

Peak inrush current i A Transformer shortcircuit power Sk kVA Rated capacitor output Q kVAr Rated capacitor current IN ARated voltage UN V

Ohmic resistance = X C

3 * UN2

* (1/Q1+ 1/Q2)

Grid impedance = XI o*L () including contactor fuse busbars

Calculation example

Given parameters:

Grid connection of a single 50 kVArcapacitor, no other capacitor connected:a Grid 400 V/50 Hza Transformer shortcircuit voltage: 5%a Transformer output: 1600 kVAa Capacitor Q = 50 kVAr; IN = 72 A

i = = 2575 A

The inrush current is approximately35 times the rated current.

Typical inrush currents are

1040 times the rated current forsingle capacitors during connection.

1600 kVA

2* 0.05 *72 A50 kVAr

i=2*Sk

*INQ

^

Eq 2

^

^


7/12

Connection of a 50 kVAr capacitor, other300 kVAr capacitors are already connected:a Grid 400 V/50 Hza Transformer shortcircuit voltage: 6%a Transformer output: 630 kVAra Q1 = 50 kVAra Q2 = 300 kVAra IN = 72 A ; VN = 400 V ; f = 50 Hz

aXC = 3 * U2N * ( + ) = 11.2

a L /phase = 0.4 H (empirical)aXL= o * L = 2 * * f * L = 0.125 m

i = = 15118.6 A

The inrush current is approximately210 times the rated current.

2*400 V

11.2 *0.125*103

1Q2

1Q1

7EPCOS AG

Various Solutionsfor Limiting Inrush Current

KLK1707-F

3C

1C

2C

C1

1Q Q2

C2 3

C

Capacitor

Contactor

Grid

L 3

L

L 2

1UN

KLK1708-N

nL

Kn K

L 2

2

1L

K1

2L

L 1

L 3 Grid

Qn Q2 Q1

UN

Parallel connecting of capacitor: Serial air coils

This example shows that cable turns in seriesbetween contactor and capacitor reduce theinrush current. Contactor suppliers recommendinductivity of 6 8 H for damping inrush current.To achieve this inductivity, the following table pro-vides tips for selecting the required turns, diame-ters and cross sections.

Given parameters: Given parameters:

Parallel connection of a 50 kVAr capacitorwith cable turns (serial aircoils) for damping,other 300 kVAr capacitors are already connect-ed, 400 V/50 Hz, shortcircuit power 10.5 MVA,rated capacitor current 72 A: damping withapprox. 6 H with turns.aXc = 11.2aXL1 = 2 * * f * L = 2 * * 50 * 6 H = 1.88 m

aXL2 = 2 * *f *L =0.125 maXL total = 0.125 + 1.88 = 2 ma L /phase = 0.4 H (empirical value)1)

i = = 3780 A

The inrush current is approximately50 times the rated current. This means onlyabout a quarter compared to a capacitorwithout damping (turns).

2*400 V

11.2 *2 *103

Typical inrush currents are

100250 times rated current forsingle capacitors in parallel connectionto other capacitors in operation.

This example shows that some cable

turns in series with the capacitorcontribute to reducing inrush current(to 50 times rated current).This improves capacitor life cycle.

i=2*UN

Xc*XLi=

2*UN

Xc*(XL1+XL2)^ ^

Eq 3 Eq 4

^^

1) For switch gear and connected cables


8/128 EPCOS AG

Damping as described is a possiblesimple solution, but this methoddeals with two contradicting effects:

a Longer (or additional) cablescause electrical losses higherlosses cause higher inherenttemperature within the capacitor.

a On the other hand, cable turnsreduce the inrush current andincrease the life cycle of capaci-tors and contactors.

Plus, you must make sure that thecapacitor works below its maximumoperating temperature.

Detuning reactors(series anti-harmonic reactors)

In detuned capacitor banks theinductivity of filter circuit reactorsprovides an excellent dampingeffect for limiting inrush current.The following diagrams showthe connection of a detuned andnon-detuned (reactor and capac-itor) system.

The peak current of a conventionalcapacitor is higher than 4000 A.The peak current of detuned capac-itors is only approx. 500 A. Thepurpose of filter circuit reactors isof course not the damping ofinrush current, but this exampleshows that in the case of detunedcapacitors no additional damp-ing measures are required.

Examples for detunedcapacitor banks (ref. page 2)

Selection table for connection cables

Detuned capacitorwith series reactors

Various Solutions forLimiting Inrush Current

Capacitor Turns Approx. Cablerating diameter cross-section

5 kVAr 10 100 mm 2.5 mm2

10 kVAr 10 100 mm 4 mm2

12.5 kVAr 10 100 mm 4 mm2

16.7 kVAr 7 100 mm 6 mm2

25 kVAr 7 100 mm 10 mm2

33 kVAr 7 100 mm 25 mm2

50 kVAr 7 100 mm 35 mm2

Fig. 1: 25 kVAr (21A /690 V)vertical: 2000 A /divhorizontal: 0.625ms /div

Fig. 2: 25 kVAr (21A / 690 V)vertical: 200 A / divhorizontal: 10 ms / div

Because of the high inductance inthe circuit, the breaking qualityof the contactor is important toavoid restriking during switch-off.Especially large contactors (over-sized motor contactors) may betoo slow and are therefore critical.

> 4000 A

= 190 * IN

i = 500 A

= 24 * IN

This table should help to find the appropriate cable and required turns.

Our PFC-CDROM (available upon request) contains calculation softwarewhich enhances precise calculation of the application (capacitors andswitch gear).

Conventional capacitorwithout damping


9/129EPCOS AG

Capacitor contactors with damping resistors

How does it work?

The series damping resistors areswitched by socalled precontactsor auxiliary contacts. The precon-tact closes before main contactsand preloads the capacitor.

a Reduced voltage differences.

a The peak current is limited.

a The resistor is temporarily in thecircuit and has no thermal losses.

a The total resistance of the resistorwires is mainly ohmic in nature,its inductance can be neglected.The coiling up of the dampingresistors is only a matter of con-struction.

a During operation (main contactsare closed) the resistor wires aredisconnected or shorted out, anddo not cause any permanentlosses at all. Due to the very shortoperation time (a few milliseconds

only) during switch-on of thecontactor, a long life cycle of thedamping resistors is ensured.

Auxiliary switchedcontact with serialresistor (precontacts)

Capacitor contactor(main contacts)

Capacitor

Main contacts

Precontacts2...10 ms

on

Grid/Mains

onoff

onoff

Functional diagram

i=C*dVdt

^

Note:Due to pre-loading via aux.contacts the capacitorsvoltage difference will bereduced. Consequentlyalso the capacitor currentaccording to the formula:

Damping

resistor

Pre-switching

aux. contacts

Eq 5


10/1210 EPCOS AG

With

damping resistors

Without

damping resistors

The following two diagrams showthe difference between a capa-citors inrush current without andwith damping series resistorswhen a capacitor is switched inparallel to an already energizedcapacitor bank/unit:

Comparison

Facts and conclusion

a Rated current of a 12.5 kVar/400 V capacitor is 18 A

a Peak inrush current without series resistors is 1200 A

a Peak inrush current with series resistors is only 260 A

a 1200 A is equal to 66 times the rated current

a Inrush current with series resistors is only one fifthof that of the standard contactor

a Substantial difference also in terms of power(integrated area)

a Superior switching behavior of contactor with seriesresistors compared with a standard contactor, results inextended life cycle of contactors as well as of capacitors

a Improved power quality ensures trouble-free and safeoperation of the PFC system and application

Fig.3 : 12.5 kVAr (18 A/400 V)

vertical: 250 A/divhorizontal: 0.5 ms/div

Fig.4 : 12.5 kVAr (18 A/400 V)


i = 1200 A

i = 260 A


11/1211EPCOS AG

Without precontacts

(detuned capacitor)

With precontacts

(detuned capacitor)

Without precontacts

(non-detuned capacitor)

ComparisonCapacitor bank switching under various conditions

Facts and conclusion

The peak current during switching without using precontacts(Fig.5) exceeds 4000 A

If capacitors are detuned (Fig. 6) the peak is only 500 A

The latter case shows the influence of inductivity andprecontacts of a capacitor contactor, the peak current

(Fig.7) is reduced to approx. 200 A

Fig. 5: 25 kVAr (21A /690 V)


Fig. 6: 25 kVAr (21 A/690 V)

vertical: 200 A/divhorizontal: 10 ms/div

Fig. 7: 25 kVAr (21 A/690 V)

vertical: 200 A/divhorizontal: 10 ms/div

i > 4000 A i = 500 A

i < 200 A


12/12

Herausgegeben von EPCOS AG, Marketing Kommunikation

Postfach 801709, 81617 Mnchen, DEUTSCHLAND

(089) 636-09, FAX (089) 636-2 2689

EPCOS AG 2000. Alle Rechte vorbehalten. Vervielfltigung, Verffentlichung, Verbreitung und Verwertung dieser

Broschre und ihres Inhalts ohne ausdrckliche Genehmigung der EPCOS AG nicht gestattet.

Mit den Angaben in dieser Broschre werden die Bauelemente spezifiziert, keine Eigen-schaften zugesichert. Bestellungen

unterliegen den vom ZVEI empfohlenen Allgemeinen Lieferbedingungen fr Erzeugnisse und Leistungen der

Elektroindustrie, soweit nichts anderes vereinbart wird. Diese Broschre ersetzt die vorige Ausgabe. Fragen ber Technik,

Preise und Liefermglichkeiten richten Sie bitte an den Ihnen nchstgelegenen Vertrieb der EPCOS AG oder an unsere

Vertriebsgesellschaften im Ausland. Bauelemente knnen aufgrund technischer Erfordernisse Gefahrstoffe enthalten.

Ausknfte darber bitten wir unter Angabe des betreffenden Typs ebenfalls ber die zustndige Vertriebsgesellschaft

einzuholen.

Published by EPCOS AG, Marketing Communications

P.O.B. 801709, 81617 Munich, GERMANY

++49 89 636-09, FAX (089) 636-2 2689

EPCOS AG 2000. All Rights Reserved. Reproduction, publication and dissemination of this brochure and the information

contained therein without EPCOS prior express consent is prohibited.

The information contained in this brochure describes the type of component and shall not be considered as guaranteed

characteristics. Purchase orders are subject to the General Conditions for the Supply of Products and Services of the

Electrical and Electronics Industry recommended by the ZVEI (German Electrical and Electronic Manufacturers

Association), unless otherwise agreed. This brochure replaces the previous edition. For questions on technology, prices and

delivery please contact the Sales Offices of EPCOS AG or the international Representatives. Due to technical requirementscomponents may contain dangerous substances. For information on the type in question please also contact one of our

Sales Offices.

EPCOS AG

corrientes en los momentos de conexión

Documents