C R E A T I N G N E W E X P E C TA T I O N S

www.vektek.com Mid-Year 2020

World’s First Screw-In Cartridge Mount Link Clamps

and Twin Lever Link Clamps

TWIN LEVER LINK CLAMP DOUBLE ACTING ROTARY LUG

CARTRIDGE MOUNT LINK CLAMP DOUBLE ACTING SINGLE LEVER

TWIN LEVER LINK CLAMP DOUBLE ACTING CARTRIDGE MOUNT

Patented rotary lug feature delivers 360 degrees of lever/body positioning. This permits a cartridge mount body with no need for thread clocking. Made possible by Vektek’s patented pivot equalizing system! Available in 3 sizes, 1100lb, 1700lb, and 2600lb total clamping force at 5000 PSI. Significantly increased vertical clamping stroke over standard link clamp allows access to clamp through a hole onto the surface of work piece. Clamp on two parts with one link clamp or reach through a part hole. For clamping when work piece surfaces are within 0.060 inches. Cartridge mount body is manifold mount only. Cartridge mount body minimizes clamp footprint with simple and easy to machine cavity. Levers sold separately.

* Clamp capacities are listed at 5000 PSI maximum operating pressure with a standard length link clamp lever installed. Total clamping force is divided equally between each side. Minimum operating pressure is 500 PSI for double acting. The clamping force is adjustable by varying the hydraulic system pressure. Use of an extended length lever will result in a reduction of clamp force. (Actual force will vary slightly due to mechanical inefficiencies, and friction.) Concentric design allows reaching up through a bore to clamp a single part. ** Equal to ±10° with standard lever. *** To ensure maximum service life and trouble-free operation, restrict fluid flow to the above flow ratings when clamping. If you are unable to measure flow rates, these devices should be positioned in no less than 1/2 second. These recommendations apply when using the standard lever. When using the optional extended lever or your custom lever, please restrict the flow rates to position the lever in no less than 1 second.

NEW

ATHREAD

D

FH

NTOTAL STROKE

ABCONTACT

POINT

ABCONTACT

POINT

10CLAMPANGLE

AFMCLAMPSTROKE

BC

E

GHEX

KJL

AG

AH

AD

T

ILS160016 REV 1

For proper sealing, the mating surface must be flat within.002 in. with a maximum 63 µin Ra surface finish.

DIMENSIONS (IN)

Model No. A B C D E F G H J KDouble Acting (D/A) Cylinder, actuated hydraulically both directions.

16-4215-20 1 3/4 - 16 3.63 3.32 1.37 2.77 0.59 2.00 0.47 0.16 1.6616-4218-20 2 - 16 4.25 3.89 1.48 3.25 0.74 2.50 0.59 0.19 1.9116-4222-20 2 1/4 - 16 4.91 4.45 1.51 3.68 0.97 3.00 0.71 0.20 2.15

Model No. L M N T AB AD AF AG AH16-4215-20 1.25 0.51 0.64 2.188 1.38 54 2.97 2.24 0.84616-4218-20 1.29 0.65 0.86 2.750 1.70 56 3.46 2.56 1.06316-4222-20 1.31 0.83 1.07 3.250 2.03 54 4.02 2.90 1.201

SPECIFICATIONS

Model No.

Clamping Capacity

(lb)*

Vertical Clamping

Stroke (in)**

Effective Piston Area

(sq. in.)

Oil Capacity (cu. in.)

MaximumFlow Rate***(cu. in./min.)

Extend Extend RetractDouble Acting (D/A) Cylinders, actuated hydraulically both directions.

16-4215-20 1,100 0.18 0.274 0.141 0.051 1716-4218-20 1,700 0.24 0.394 0.259 0.080 3116-4222-20 2,600 0.29 0.616 0.511 0.186 61

SCREW-IN TWIN LEVER LINK CLAMP DOUBLE ACTING CARTRIDGE MOUNT DESIGNWITH PATENTED EQUALIZING SYSTEM!

Force equally divided between each side

U.S. Patent No. 8,678,362Other Patents Pending

Vektek’s patented Pivot Equalizing System

equally divides force between each side and allows

height variations.

DIMENSIONS (IN)

Model No. A B C D E F G H J K L M N P Q

Double Acting (D/A) Cylinders, actuated hydraulically both directions.16-3215-20 1.408 2.94 2.64 1.008 2.09 1.28 0.67 0.47 0.38 0.22 0.88 0.51 0.64 1.969 0.98416-3218-20 1.566 3.35 2.99 1.248 2.34 1.32 0.67 0.59 0.44 0.28 0.83 0.65 0.86 2.441 1.22016-3222-20 1.881 3.76 3.31 1.508 2.54 1.34 0.67 0.71 0.53 0.34 0.75 0.83 1.07 2.953 1.476

Made possible by Vektek’s patented equalizing system!Patented rotary lug feature delivers 360 degrees of lever/body positioning. This simplifies internal porting and fixture design flexibility. Available in 3 sizes, 1100lb, 1700lb, and 2600lb total clamping force at 5000 PSI.Significantly increased vertical clamping stroke over standard link clamp allows access to clamp through a hole onto the surface of work piece.Clamp on two parts with one link clamp.For clamping when work piece surfaces are within 0.060 inches. Top flange body can be manifold mounted or plumbed. Levers sold separately. Optional In The Port Flow Control is a meter-in device with reverse free flow check valve. Optional In The Port Sequence Valve is a sequencing device with reverse free flow check valve.

SPECIFICATIONS

Model No.Clamp

Capacity(lbs)*

Vertical Clamping

Stroke (in.)**

Effective Piston Area

(sq. in.)

Oil Capacity (cu. in.)

MaximumFlow Rate***(cu. in./min.)

Extend Extend RetractDouble Acting (D/A) Cylinders, actuated hydraulically both directions.

16-3215-20 1,100 0.18 0.274 0.141 0.051 1716-3218-20 1,700 0.24 0.394 0.258 0.080 3116-3222-20 2,600 0.29 0.616 0.509 0.186 61

* Clamp capacities are listed at 5000 PSI maximum operating pressure with a standard length link clamp lever installed. Total clamping force is divided equally between each side. Minimum operating pressure is 500 PSI for double acting. The clamping force is adjustable by varying the hydraulic system pressure. Use of an extended length lever will result in a reduction of clamp force. (Actual force will vary slightly due to mechanical inefficiencies, and friction.) ** Equal to ±10° with standard lever. *** To ensure maximum service life and trouble-free operation, restrict fluid flow to the above flow ratings when clamping. If you are unable to measure flow rates, these devices should be positioned in no less than 1/2 second. These recommendations apply when using the standard lever. When using the optional extended lever or your custom lever, please restrict the flow rates to position the lever in no less than 1 second.

NEW TWIN LEVER LINK CLAMP DOUBLE ACTING ROTARY LUG DESIGNWITH PATENTED EQUALIZING SYSTEM!

A

D L AH

GF

H NTOTAL STROKE

Z

X

Y VT

ABCONTACT

POINTQ

P

R

S

ABCONTACT

POINT

BC

EAG

10CLAMPANGLE

AD

AF

MCLAMPSTROKE

For proper sealing, the mating surface must be flat within.003 in. with a maximum 63 µin Ra surface finish.

K THRUJW

CLAMPMANIFOLD

PORTO-RING

AACLAMP

PORT

AAUNCLAMP

PORT

WUNCLAMP

MANIFOLDPORT

O-RING

ILS160013 REV 1

Model No. R S T V W X Y Z AA AB AD AF AG AH16-3215-20 0.797 0.797 2.402 0.984 2-011 0.433 1.093 0.43 SAE 4 1.38 54 2.283 1.555 0.84616-3218-20 0.985 0.985 2.835 1.220 2-011 0.551 1.289 0.55 SAE 4 1.70 56 2.559 1.654 1.06316-3222-20 1.188 1.188 3.445 1.476 2-011 0.630 1.644 0.63 SAE 4 2.03 54 2.874 1.752 1.201

Port Depth for Optional In-Port Valves: SAE 4 X .58In-port valves require the use of manifold mount ports

Force equally divided between each side

U.S. Patent No. 8,678,362Other Patents Pending

CARTRIDGE MOUNT LINK CLAMP CAVITY DIMENSIONS

DIMENSIONS (IN)

Model No. A B C D E F G H J INSTALLATIONTORQUE

Cartridge Mount, TuffLinkTM360 Single and Twin Lever Link Clamp

16-4215-00 16-4215-20 1 3/4 - 16 0.38 1.689 0.50 1.78 0.250 0.189 0.157 0.561 110 ft-lb

16-4218-00 16-4218-20 2 - 16 0.50 1.939 0.63 2.03 0.250 0.252 0.188 0.658 150 ft-lb

16-4222-00 16-4222-20 2 1/4 - 16 0.63 2.189 0.75 2.28 0.250 0.341 0.188 0.725 200 ft-lb

(D MIN)

(B MIN)

(G RADIUS) (J RADIUS)

H MAXON J RADIUSUNCLAMP FEED.150 MIN

2 PLCS

63

R.020 MAX

A THREAD UN-2B B MINMINOR C .007 D MIN

90° X E.002 A

F MAXON OR INSIDE G RADIUSCLAMP FEED

.002-A-

ILS160020 REV A

H

A

Q .003

L

RADIUS T

B

S

M

RADIUS G

N .005

P

RADIUS G

R

C

K .003

FJ .005

E

D .005

SEE DETAIL RIGHT

ILS916017 REV 1

TWIN LEVER LINK CLAMP STANDARD LEVER DIMENSIONS (IN)

Model No. A B C D E F G H

J KMAX MIN

91-6115-20 1.18 1.51 0.551 0.472 0.167 0.197 0.197 0.2384 0.2370 0.551 0.11891-6118-20 1.48 1.87 0.709 0.551 0.197 0.276 0.197 0.3169 0.3155 0.719 0.15791-6122-20 1.76 2.24 0.787 0.709 0.256 0.354 0.236 0.3956 0.3942 0.856 0.079

Model No.L

M N P Q R S TMAX MIN

91-6115-20 0.2370 0.2362 25 0.280 0.370 0.197 0.451 27 0.19791-6118-20 0.2764 0.2756 30 0.319 0.453 0.217 0.524 29 0.25691-6122-20 0.3552 0.3544 25 0.398 0.630 0.335 0.591 25 0.394

TWIN LINK CLAMP LEVER DIMENSIONS

NEW SCREW-IN CARTRIDGE MOUNT LINK CLAMP DOUBLE ACTING SINGLE LEVER DESIGN

Patented rotary lug feature delivers 360 degrees of lever/body positioning. Available in 3 sizes, 1000lb, 1400lb, and 2400lb total clamping force at 5000 PSI.Cartridge mount body is manifold mount only.Cartridge mount body minimizes clamp footprint with easy to machine cavityMaximum clamping force - minimal footprint. Levers sold separately.

* Clamp capacities are listed at 5000 PSI maximum operating pressure with a standard length link clamp lever installed. Minimum operating pressure is 500 PSI for double acting. The clamping force is adjustable by varying the hydraulic system pressure. Use of an extended length lever will result in a reduction of clamp force. (Actual force will vary slightly due to mechanical inefficiencies, and friction.) ** Equal to ±3° with standard lever. *** To ensure maximum service life and trouble-free operation, restrict fluid flow to the above flow ratings when clamping. If you are unable to measure flow rates, these devices should be positioned in no less than 1/2 second. These recommendations apply when using the standard lever. When using the optional extended lever or your custom lever, please restrict the flow rates to position the lever in no less than 1 second.

DIMENSIONS (IN)

Model No. A B C D E F G H J KDouble Acting (D/A) Cylinders, actuated hydraulically both directions.

16-4215-00 1 3/4-16 4.29 3.58 1.37 2.87 0.59 2.00 0.47 0.16 1.6616-4218-00 2-16 5.07 4.11 1.48 3.32 0.74 2.50 0.59 0.19 1.9116-4222-00 2 1/4-16 5.83 4.79 1.51 3.80 0.97 3.00 0.71 0.20 2.15

SPECIFICATIONS

Model No.

ClampingCapacity

(lbs)*

Vertical Clamping

Stroke (in.)**

Effective Piston Area

(sq. in.)

Oil Capacity (cu. in.)

MaximumFlow Rate***(cu. in./min.)

LEVERS

STANDARD EXTENDEDExtend Extend Retract

Model No.Double Acting (D/A) Cylinders, actuated hydraulically both directions.16-4215-00 1,000 0.10 0.274 0.213 0.077 26 91-6115-01 91-6115-0216-4218-00 1,400 0.12 0.394 0.379 0.116 45 91-6118-01 91-6118-0216-4222-00 2,400 0.14 0.616 0.715 0.258 86 91-6122-01 91-6122-02

U.S. Patent No. 8,678,362

Model No. L M N T AB AD AF AG AH16-4215-00 1.25 0.78 0.92 2.188 1.63 18 3.10 2.24 1.06316-4218-00 1.29 0.96 1.11 2.750 2.01 19 3.64 2.56 1.20116-4222-00 1.31 1.16 1.34 3.250 2.32 19 4.19 2.90 1.457

ILS160018 REV A

HK

ATHREAD

DAG

AH

E

CB

3CLAMPANGLE

JL F

MCLAMPSTROKE

NTOTAL STROKE

AF

AD

GHEX

ABT

For proper sealing, the mating surface must be flat within.002 in. with a maximum 63 µin Ra surface finish.

ILS160019 REV A

Visit our catalog or website for Link

Clamp Levers Options

Vektek is...

PowerClampingInnovationLike you, we are a metalworkingmanufacturer. We understand thedemands of production and profitability.Our engineers strive to implement the latest technology and intelligence intothe design of our workholding products.Vektek is known, worldwide, for innovativesolutions, the reliability of our products andour extraordinary sales and technicalsupport teams. Team Vektek is here to assistin any way to see that your move to, orimprovement of, Precision Power Workholdingis easy and cost effective.

Contact us to receive a free catalog:

800-992-0236sales@vektek.com

Go to:www.vektek.com

Download catalog PDFand CAD drawings

Also available in: • Chinese • Japanese • Korean • Portuguese • Spanish

Troy Estes, PresidentVektek LLC