crl essence series rolling shower door system with … · 2018. 7. 9. · installation instructions...
TRANSCRIPT
INSTALLATION INSTRUCTIONS
2503 E. Vernon Avenue, Los Angeles, CA 90058-1826(800) 421-6144 Fax (800) 262-3299crlaurence.com ALUMINUM
CRL ESSENCE SERIES ROLLING SHOWER DOOR SYSTEM
WITH HEADER
11M0338_REV A_7-6-18
ESS560_ ESS584_
64” (1626 mm) Degree Rounded Style Essence Kit with Header 84” (2134 mm) Rounded Style Essence Kit with Header
ESS760_ ESS784_
64” (1626 mm) Degree Squared Style Essence Kit with Header 84” (2134 mm) Squared Style Essence Kit with Header
BR4_ SR4_ HTG4BN EHSSA
Rounded Style Rollers (2) Squared Style Rollers (2) Top Roller Guides (2) Roller Stop
FGF4_ ESSLSS* ESSH60_ ESSH84_
180 Degree Fixed Glass Fittings (2)
Spanner Wrench for Roller Adjustment
60” (1524 mm) Header with Snap Cover
84” (2134 mm) Header with Snap Cover
SDCD12_ SDCEC12_ SVE301_ SVE301_
98” (2489 mm) U-Channel End Cap for U-Channel60” (1524 mm) Bottom Track
with Mounting Strip84” (2134 mm) Bottom Track
with Mounting Strip
SBRSDG* BWB2 DK98L SB596
Drill Jig Brass Wall Mounting Brackets (2) Clear Plastic L-Seal 1/16” Setting Block (Use as Guide)
Kit Contains:1 64” (1626 mm) Header with Snap Cover2 Top Roller Guides1 Door Stop2 Fixed Glass Fittings2 Wall Mounting Brackets1 Drill Jig1 64“ (1626 mm) Bottom Track with Mounting Channel and Fasteners1 98” (2489 mm) L-Seal1 98” (2489 mm) U-Channel1 End Cap for U-Channel2 Rounded Style Bottom Rollers1 Spanner Wrench
INTERIOR
NOTE: Glass Panels Not Included.
Kit Contains:1 84” (2134 mm) Header with Snap Cover2 Top Roller Guides1 Door Stop2 Fixed Glass Fittings2 Wall Mounting Brackets1 Drill Jig1 84“ (2134 mm) Bottom Track with Mounting Channel and Fasteners1 98” (2489 mm) L-Seal1 98” (2489 mm) U-Channel1 End Cap for U-Channel2 Rounded Style Bottom Rollers1 Spanner Wrench
INTERIOR
NOTE: Glass Panels Not Included.
INTERIOR
NOTE: Glass Panels Not Included.
Kit Contains:1 64” (1626 mm) Header with Snap Cover2 Top Roller Guides1 Door Stop2 Fixed Glass Fittings2 Wall Mounting Brackets1 Drill Jig1 64“ (1626 mm) Bottom Track with Mounting Channel and Fasteners1 98” (2489 mm) _-Seal1 98” (2489 mm) U-Channel1 End Cap for U-Channel2 Squared Style Bottom Rollers1 Spanner Wrench
Kit Contains:1 84” (2134 mm) Header with Snap Cover2 Top Roller Guides1 Door Stop2 Fixed Glass Fittings2 Wall Mounting Brackets1 Drill Jig1 84“ (2134 mm) Bottom Track with Mounting Channel and Fasteners1 98” (2489 mm) L-Seal1 98” (2489 mm) U-Channel1 End Cap for U-Channel2 Squared Style Bottom Rollers1 Spanner Wrench
INTERIOR
NOTE: Glass Panels Not Included.
ESSENCE SERIES SLIDING SHOWER DOOR WITH HEADER
ALUMINUM2crlaurence.com | usalum.com
PARTS LIST
* Available through Technical Sales at (323) 588-1281 NOTE: ESS560_ installation drawings shown in this manual. Other installations similar.
EXTERIOR
Center Line1-19/32”(40 mm)
OV
ER
ALL
HE
IGH
T
FIX
ED
PA
NE
L
SLI
DIN
G D
OO
R
HeaderHeight2-5/16”(59 mm)
OV
ER
ALL
HE
IGH
T
OPENING WIDTHFRAME LENGTH
Drawing not to scale. Shown from interior.
NOTE: For use with 3/8” or 1/2” (10 or 12 mm) Tempered Glass. Do Not use Laminated Glass.
ESSENCE SERIES SLIDING SHOWER DOOR WITH HEADER
ALUMINUM3crlaurence.com | usalum.com
ORDER OF ASSEMBLY AND INSTALLATIONPARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3GLASS FABRICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4SITE PREPARATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Mark Location for Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5FRAME FABRICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6FRAME INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 9
Install Mounting Strip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Install Bottom Track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Prepare Header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Install Header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Install U-Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Install Fixed Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
SLIDING DOOR ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Install Top Roller Guides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Install Bottom Rollers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
SLIDING DOOR INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Install Sliding Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Install Anti-Lift Guides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
FINISHING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Install L-Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Install Snap Cover for Header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
SPECIFICATIONS
IMPORTANT: READ THIS MANUAL THOROUGHLY BEFORE BEGINNING INSTALLATION.
NOTE: Drawings not shown to scale. Frame is cut 1/16” (2 mm) less than Opening Width and centered in opening. Overall Height is height from curb/floor to top of Header. Drawings shown from interior.
NOTE: For use with 3/8” or 1/2” (10 or 12 mm) Tempered Glass. Do Not use Laminated Glass.
OV
ER
ALL
HE
IGH
T
OPENING WIDTHFRAME LENGTHFixed Glass set 1/8” (3 mm) from wall. 1/4” (6 mm) Gap
between Sliding Doorand wall for L-Seal.
3/16” (5 mm)Gap for U-Channeland Setting Block.
Fixed Glass aligns with top of Header.
Fixed Glassoverlaps
Sliding Door2-7/8” (73 mm)
FIXED PANEL
3/4” (19 mm)Diameter
4” (102 mm) 4” (102 mm)
FIX
ED
PA
NE
L H
EIG
HT
FIXED PANEL WIDTH
1-5/16”(33 mm)
4” (102 mm)4” (102 mm)1-13/16”(46 mm)
SLIDING DOOR GLASS
3” (76 mm)Diameter
1/2”(13 mm)Diameter
5/8”(16 mm)
Holesfor Handle
4” (102 mm) 4” (102 mm)1-3/8”(34 mm)
1-3/8”(34 mm)
3/8”(10 mm)1/4” (6 mm) MAX
relief cut opening
SLI
DIN
G D
OO
R H
EIG
HT
SLIDING DOOR WIDTH
FIXED PANEL WIDTH : Opening Width Divided by 2 plus 1-1/4” (32 mm)
SLIDING DOOR WIDTH : Opening Width Divided by 2 plus 1-1/4” (32 mm)FIXED PANEL HEIGHT : Overall Height minus 3/16” (5 mm)
SLIDING DOOR HEIGHT : Overall Height minus 2” (51 mm)
ESSENCE SERIES SLIDING SHOWER DOOR WITH HEADER
ALUMINUM4crlaurence.com | usalum.com
GLASS FABRICATION
For use with 3/8” or 1/2” (10 or 12 mm) Tempered Glass.NOTE: DO NOT use Laminated Glass.
EXTERIOR
OV
ER
ALL
HE
IGH
T
Top of Header
Mounting Height1/4” (6 mm)
1-19/32”(40 mm)
Center Line
Allow minimum1-19/32” (40 mm)
from Center Line to edge.
EXTERIOR
Mark Mounting Holeat Overall Height
minus 1/4” (6 mm).
Top of Header
MarkCenter Line Mark
Center Line
1-19/32”(40 mm)
OV
ER
ALL
HE
IGH
T
MO
UN
TIN
G H
EIG
HT
Top of Header
Header Heightis 2-5/16” (59 mm)
1/4” (6 mm)
Bottom of Header
Drawing not to scale. Shown from interior.
ESSENCE SERIES SLIDING SHOWER DOOR WITH HEADER
ALUMINUM5crlaurence.com | usalum.com
SITE PREPARATIONMark Location for Frame
1
2
Cut Header and Snap Cover.
Cut Bottom Track and Mounting Strip from same end.
Cut U-Channel for Fixed Panel.
NOTE: The Bottom Track and Mounting Strip are fabricated with the same drainage system on both ends. Determine if the surface is out of level first and then cut excess from the same end of both profiles so the drains will align at the low side of the surface when installed.
3
EXTERIOR
Header SnapCover
Mounting Strip
Bottom Track
U-Channel
EXTERIOR
U-Channel
U-CHANNEL WIDTH = OPENING WIDTH
DIVIDED BY 2 PLUS 1-3/8” (35 MM)
2
EXTERIOR
OPENING WIDTHLevel Line
OPENING WIDTH
Lower End
Cut Excess from SameEnd of Both Profiles
so Drains Align.
1
1
EXTERIOR
MountingStrip
BottomTrack
B
A
TRACK WIDTH = OPENING WIDTH MINUS 1/16” (2 MM)
Ensure correct orientation of profilesbefore cutting. Position drains
at Low End of Surface.
HEADER WIDTH = OPENING WIDTH MINUS 1/16” (2 MM)
Header
SnapCover
3
3 B
A
ESSENCE SERIES SLIDING SHOWER DOOR WITH HEADER
ALUMINUM6crlaurence.com | usalum.com
FRAME FABRICATIONCut Bottom Track, Header and U-Channel
1/2”(13 mm)
2
2
Positiondrain at low end.
EXTERIOR
A1
1
Mount with #8 Flat Head Screws suitable for substrate.
Screws by others.
B
1 Install Mounting Channel.
Seal 1/2” (13 mm) at each end.
NOTE: Ensure Mounting Channel is set at correct orientation with drain at low end.
NOTE: Drill holes 6” (152 mm) from ends and 12” (305 mm) maximum in between.
Lower End
2 Silicone at Ends.
Install Bottom Track.3
B
A
3
EXTERIOR
Mounting Channel
Bottom TrackU-Channel
Allow 11/16” (17 mm) gap to mount U-Channel.
3 B
A3
Align Drains.
Fasten at all hole locations with included 8-32 x 5/16” Flat Head Phillips
Machine Screws.
1/2”(13 mm)
2
ESSENCE SERIES SLIDING SHOWER DOOR WITH HEADER
ALUMINUM7crlaurence.com | usalum.com
FRAME INSTALLATIONInstall Mounting Strip
Install Bottom Track
2
1
5/32”(4 mm)
Gap
1/32”(3 mm)
Gap
FIXED GLASS
1”(25 mm)
A Mark holes for Fixed Glass Fittings.
1
Install Roller Stop.
Install Right and Left Wall Mounts.
Drill clearance holes in Header for Fixed Glass Fittings.
NOTE: Adjust Stop position after installing Sliding Door.
3
4
B Slide Drill Jig on top of Header and align
to each mark.
Drill 5/16” (6 mm) Holesat marked locations.
1
A
Rubber Stop Faces Sliding Door.
3
B
Tighten Set Screws to Secure.
3
CAlign ConnectingNut to Clearance Hole and install Header Mount and Gasket with Shoulder Stud.Header
Mount
ShoulderStud
Gasket
B2
Install Fixed Glass Fitting mounts.
A Unpack Fixed Glass Fittings and separate parts.
ShoulderStud
HeaderMount
Gasket
End Capwith Gasket
ConnectingNut
2
B
C
SlideConnectingNuts intoHeader.
2
Align flush to end and tighten Set Screws to Secure.
B4
Slide Left Wall Mount into left end of Header.
A4
Align flush to end and tighten Set
Screws to Secure.
D4Slide Right Wall Mount
into right end of Header.
C4
ESSENCE SERIES SLIDING SHOWER DOOR WITH HEADER
ALUMINUM8crlaurence.com | usalum.com
FRAME INSTALLATION (CONTINUED)Prepare Header
2NOTE: Use fasteners suitable for substrate. Space 6” (152 mm) from ends and 12” (305 mm) maximum in between.
NOTE: Place Setting Blocks at quarter points in U-Channel before setting glass. (Setting Blocks not included)
3
1
1
Attach End Cap to U-Channel and mount 1/8” (3 mm) from wall.
Mount Header to walls.
Install Fixed Glass Panel.
EXTERIOR
GasketEnd Cap
3 C
A2
AttachEnd Cap.
EXTERIORBottom Track
U-ChannelSeal and tool
between U-Channel and Bottom Track.
2 DSecure withscrews by
others.
2 C
1/8” (3 mm)Gap
Position withgap at wall.2 B
CFit End Cap with Gasket through clearance hole
in Fixed Panel.
3 D
Twist onto Shoulder Stud and turn until tight.
3
3
3
EXTERIOR
LowerFixed Panel
into U-Channel.
Align Clearance Holes with Fixed Glass Mounts.B
A
1
ESSENCE SERIES SLIDING SHOWER DOOR WITH HEADER
ALUMINUM9crlaurence.com | usalum.com
FRAME INSTALLATION (CONTINUED)Install Header
Install U-Channel
Install Fixed Panel
Remove protective tape from top gasket and install. Place Side Gasket on base. Install Plastic Bushings and fit into holes in glass. NOTE: Top Guides packaged with one top gasket, and two sets
of side gaskets. Use Thick Gaskets for 3/8” (10 mm) glass or Thin Gaskets for 1/2” (12 mm) glass.
4
Top Roller GuideAssembled
Thick SideGaskets
Thin SideGaskets
Top Gasket
1
12
3
Unpack Top Roller Guides and remove Clamping Plates.
Remove protective liner from top gasket and install. Place Side Gasket on base. Install Plastic Bushings and fit into holes in glass.
Remove protective liner from Side Gaskets. Install on Roller Body and Clamping Plate.
Adjust wheel height and tighten.
NOTE: Loosen center bolt one full turn to adjust. Use included Spanner Head to rotate cam and raise wheel height +/- 1/8” (3 mm). Begin with wheel at minimum position. Tighten center bolt snugly to hold position.
Secure Clamping Plate with Side Gasket to Guide Body.
Fit Roller Body into hole in glass. Align Clamping Plate on other side and permently tighten.
Unpack Bottom Rollers and remove Clamping Plates.
2
3
B
2 A
PlasticBushings
4
6
5
7
Align Bottom RollersFlush to Bottom Glass.
7
Thick SideGaskets
Thin SideGaskets
Anti-Lift Guardwith Screws
SpannerHead
Bottom RollerAssembled
6
6
Top Roller Guides
Bottom Rollers
INTERIORFACING UP
NOTE: Bottom Rollers packaged with two sets of side gaskets. Use Thick Gaskets for 3/8” (10 mm) glass or Thin Gaskets for 1/2” (12 mm) glass. Anti-Lift Guard is installed after door installation.
A5Loosen
Center Bolt
5Securely Tighten
Center Bolt
D
1/8”(3 mm)
MaximumHeight
MinimumHeight
Adjust to MinimumHeight.
5 C
5Use Included
Spanner Headto Turn Cam.
B
Spanner Driverby Others
ESSENCE SERIES SLIDING SHOWER DOOR WITH HEADER
ALUMINUM10crlaurence.com | usalum.com
SLIDING DOOR ASSEMBLYInstall Top Roller Guides
Install Bottom Rollers
INTERIOR
2
3
1
Test door and adjust as needed.
Lift Sliding Door up into header, swing into place and lower onto Bottom Track.
Install Anti-Lift Guards on Rollers.
INTERIOR
3 B
Slide Door to other side. Loosen Door Stop as shown on Page 8. Position so door does not run into wall and handle will not hit fixed panel glass. Tighten securely.
Slide door to wall and check vertical reveal. See Page 10 to adjust wheel height. Tighten securely when finished.
3
PushAnti-Lift tight
and secure screws.
INTERIOR
CNOTE: The Anti-Lift Guard is installed with a 1/16” (1 mm) gap between the top of the guard and the bottom of the Bottom Track. Use included Setting Block as a guide for proper clearance.
RemoveSetting Block.
INTERIOR
3 D
B3
Attach withincluded Screws.
INTERIOR
3 A
Place included Setting Block on Anti-Lift as a guide.
SettingBlock
Anti-LiftGuard
1
1
A
B
INTERIOR
2 A
2 B
2 B
2 A
ESSENCE SERIES SLIDING SHOWER DOOR WITH HEADER
ALUMINUM11crlaurence.com | usalum.com
SLIDING DOOR INSTALLATION Install Sliding Door
Install Anti-Lift Guides
2
1
Attach Snap Cover to Header.
Cut and install L-Seal.
NOTE: Temporarily attach L-Seal to Sliding Door and use as guide for final position.
NOTE: Dry fit Snap Cover before permanently installing.
CutL-SealLength
Top ofGlass Door
Top ofBottom Track
A
2 B
C
Fit Snap Cover into Headerat slight angle.
Swinginto place.
INTERIORRemove protectiveliner from Snap Cover.
A2
C1
D1
Remove protectiveliner fromL-Seal.
Close Door soL-Seal adheres to wall.
E1
F1Open Door and push seal firmly
into place.
Remove painter’stape from Door.
INTERIOR
Align L-Seal totop of glass.
Temorarily attachto Door with
painter’s tape.
B1
L-Seal
INTERIOR
INTERIOR INTERIOR
INTERIOR
ESSENCE SERIES SLIDING SHOWER DOOR WITH HEADER
ALUMINUM12crlaurence.com | usalum.com
FINISHINGInstall L-Seal
Install Snap Cover for Header