.......... css£SW

REFRIGERATORUseCs GuidePlease read this guide thoroughly

before operating and keep it handy for:e at all times.

manuel

le

Lea detenidamente

!@i!_i!ii!ii!ii!i!!i!!!!i!iiiiiiiiiiiiiiiiiiiiiiii/ii@iii@/ii@iii_i

Introduction

Installation

Operation

Suggestion onfood storage

Care andmaintenance

Table of contents

Entry

Important safety instruction

Identification of parts

Where to install

Door removal

Door replacement

Feed water pipe installation

Water connection instruction guide

Operation instruction guide

Height adiustment

Starting

Adjusting the temperatures and functions

(Dispenser / Automatic ice maker)

Shelf (Applicable to some models only)

Wine holder (Applicable to some models only)

Egg box

Humidity control in the vegetable compartment

Convert into a vegetable or meat compartment

Deodorizer (Applicable to some models only)

Location of foods

Storing foods

How to dismantle parts

General information

Cleaning

Trouble shooting

Recommended

GroundingMethod

Accessibility ofSupply Plug

Supply CordReplacement

Entry

The model and serial numbers are found on the inner case or back of refrigeratorcompartment of this unit. These numbers are unique to this unit and notavailable to others. You should record requested information here and retainthis guide as a permanent record of your purchase. Staple your receipt here.

Date of purchase

Dealer purchased fromDealer address

Dealer phone no.Model no.

Serial no.

Important safety instruction

Before it is used, this refrigerator must be properly installed and located in accordance withthe installation instructions in this document,

Neverunplugyour refrigeratorby pullingonthe power cord,Alwaysgrip plugfirmly andpullit straightout from the outlet,

When movingyour applianceaway from the wall, be carefulnot to rolloverthe power cordor to damageit inany way,

Afteryour refrigeratoris inoperation,do not touchthe cold surfaces in the freezercompartment,particularlywhen your handsaredamp orwet, Skincould adhereto theseextremelycold surfaces,

Unplugthe power cord from the power outlet for cleaningor other requirements,Nevertouch it with wet handsbecauseyou canget anelectricshock or behurt,

Neverdamage,process,severelybend,pullout, or twist the power cord becausedamagethe power cord maycausea fire or electricshock,Youhavedoubts onwhether theapplianceis properlygrounded,

Neverplaceglassproducts in the freezerbecausethey may bebrokendue to expansionwhen their contentsarefrozen.

Neverallowyour handswithin the ice storagebinof the automatic ice maker.Youcould behurt by the operationof the automatic ice maker,

Theapplianceis not intendedfor useby young childrenor infirmpersonswithoutsupervision,

Youngchilderenshouldbe supervisedto ensurethat they do not playwith the appliance,

Neverallow anyoneto climb, sit, standor hangonthe refreshmentcenterdoor, Theseactionsmaydamagethe refrigeratorandeven tip it over,causingseverepersonalinjury,

Before you move your refrigerator into its final location,it is important to make sure you have the proper electricalconnection:

A 115Volt,60 Hz,,AConly 15or 20ampere fused,groundedelectricalsupply is required,It is recommendedthat aseparatecircuitservingonlyyour refrigeratorbe provided,Useanoutlet thatcannotbeturned off by aswitch. Do not use anextensioncord.

Therefrigerator-freezershouldbe so positionedthat the supplyplug isaccessiblefor quickdisconnectionwhen accidenthappens.

If the supplycord is damaged,it must bereplacedby the manufactureror its serviceagentorasimilarlyqualifiedpersoninorder to avoida hazard,

Child entrapment

warning

Don't store

Grounding (Earthing)

Doorrack

Automaticicemaker

Lamp

Shelf(steelor glass)

Door rack .......................(Optional)

Shelf

Drawer(1or 2)

Door rack(Optional)

Lowercover .................................................................................................................................

DANGER:Risk of child entrapment.Before you throw away your old refrigerator or freezer:Take off the doors but leavethe shelves in place so that children may not easilyclimbinside.The appliance is not intended for use by young children or infirm persons withoutsupervision.Young children should be supervised to ensure that they do not playwith the appliance.

Don't store or use gasoline or other flammable vapor and liquids in the vicinity of this orany other appliance.

In the event of an electric short circuit, grounding (earthing)reduces the risk of electricshock by providing an escape wire for the electric current,In order to prevent possibleelectric shock, this appliance must be groundedimproper use of the grounding plug can result in an electric shock. Consult a qualifiedelectrician or service person if the grounding instructions are not completelyunderstood, or if you have doubts on whether the appliance is properly grounded.

Identification of parts

Freezer Refrigeratorcompartment compartment

Milk productcorner

Lamp

................... Shelf...........................Door rack

Wine holder(Optional)

Shelf

Snackdrawer (Optional)

Eggbox

Lamp

Vegetabledrawer(1or 2)

Door rack

Vegetabledrawer/Meatdrawer

Humidityswitch

Conversionswitch(Meats/Vegetables)

Select a goodlocation

Where to install

1. Place your appliance where it is easy to use.

2. Avoid placing the unit near heat sources, direct sunlight or moisture.

3. To avoid vibrations, the appliance must be leveled.

4. Don't install the appliance below 5°C. It may cause affect the performance.

z_ Warning

Remove lowercover and

then feed watertube

Remove thefreezer

compartmentdoor

Remove therefrigerator

door

Door removal

ElectricShock HazardDisconnect electricalsupply to refrigerator before installing.

Failureto do so could result in death or serious injury. [_If your accessdoor is too narrow for the _,_ _:::_-_--J_refrigerator to passthrough, remove the Lower cover

refrigerator door and passthe refrigerator laterally. -- ; _ _ _Removethe lower cover by liftingupward,and J _/:;_1then pullupthe feed water tube while pressing _/ "@"k.area¢ shown inthe figureto the right. Feed watertube

1)Removingthe hingecover by loosening thescrews.Separateallconnectionwires exceptfor the earth line after.

2) Removethe keeper by rotating it counterclockwise (@)andthen lifting the upperhinge up(@).

Hinge /" ........................ Connection)_, cover //f_" w res

Uppe_hing /J'_ "j ',\ __ EarthNne

Kee?_ [_pei hinge,gx

3) Removethe freezercompartmentdoorbylifting it upward.This time, the door shouldbe lifted enoughfor the reed water pipetubeto be completelypulledout.

Lower hinge

1) Loosen the hinge cover screws and remove

the cover, Remove connection wire, if any,except for the earth line.

wires

2) Remove keeper by rotating it clockwise (@)and then remove the upper hinge by liftingit up (@).

3) Removethe refrigeratorcompartment doorby lifting it up.

Lower hinge

Pass the

refrigerator

Beforeinstallation

Passthe refrigerator laterally through the accessdooras shown inthe right figure,

Door replacement

Mount them inthe reverse sequence of removal after they passthrough the accessdoor.

Feed water pipe installation

• Automatic ice maker operation needs water pressure of 147-834 kPa (1.5-8.5kgr/cm2)(That is, an instant paper cup (180 cc) will be fully filled within 3 sec.).

• If water pressure does not reach the rating 147 kPa (1.5 kgf/cm 2)or below, it isnecessary to purchase a separate pressure pump for normal automatic icing andcool water reed.

• Keep the total length of the feed water pipe tube within 8 m and be careful for thetube not be bent. If the tube is 8 m or longer it may cause trouble in water feedowing to the drain water pressure.

• Install the reed water pipe tube at a place free from heat.

Warning • Connect to potable water supply only.• Refer to instructions with water filter kit for installation.

Connectingthe refrigerator

to a water source

Warning

Tools required

Cold water supply

Water connection instruction guide

Read all directions carefully before you begin.

Connect to potable water supply only.

• Standard screwdriver

• 7/16 - inch and 1/2 -inch open-end wrenches or two adjustable wrenches• 1/4 -inch nut driver• 1/4 -inch drill bit

• Hand drill or electric drill (properly grounded)

The ice maker water valve contains a flow washer which is used as a water

pressure regulator.

The ice maker needs to be connected to a cold water line with water pressure207 o-827 kPa (30 o-120 psi).

Ira problem occurs, call your utility company.

Connectthe tubing to

water line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long enough to emptywater pipes.

3. Find a 1/2 -inch to 1-1/4 -inch vertical COLD water pipe near the refrigerator,

4. To determine the length of copper tubing you will need, measure from theconnection on the lower left rear of the refrigerator to the water pipe. Add 7feet (2.1m)to allow for moving refrigerator for cleaning. Use 1/4 -inch O.D.(outside diameter) copper tubing. Be sure both ends of copper tubing are cutsquare.

5. Using a grounded drill, drill a 1/4 - inch hole in the cold water pipe you haveselected.

6. Fasten shut - off valve to cold water pipe with pipe clamp. Be sure outlet endis solidly in the 1/4dnch drilled hole in the water pipe and that the washer isunder the pipe clamp. Tighten packing nut. Tighten the pipe clamp screwscarefully and evenly so washer makes a watertight seal. Do not over tighten oryou may crush the copper tubing, especially if soft (coiled) copper tubing isused. Now you are ready to connect the copper tubing.

7. Slip compression sleeve and compression nut on copper tubing as shown.Insert end of tubing into outlet end squarely as far as it will go. Screwcompression nut onto outlet end with adjustable wrench. Do not over tighten.

8. Place the free end of the tubing into a container or sink, and turn ON mainwater supply and flush out tubing until water is clear. Turn OFF shut- off valveon the water pipe. Coil copper tubing.

Pipe

Packing Nut\Coil of polyethylene or

Shut Off Valve Copper Tubing

Compression Sleeve Compression Nut

Connect the tubing tothe refrigerator

Turn the water on atthe shutoff valve

Automatic ice maker

Operation instruction guide

Before making the connection to the

refrigerator, be sure the refrigerator

power cord is not plugged into the walloutlet.

1. Remove the plastic flexible cap fromthe water valve.

2. Place the compression nut and ferrule(sleeve) onto the end of the tubing asshown.

3. Insert the end of the copper tubing intothe water valve connection as far aspossible. While holding the tubing,tighten the fitting.

(Provided)Compression nut

(Provided) *_

Ferrule

Copper tubing

Tighten any connections that leak.

• Plug In the RefrigeratorArrange the coil of copper tubing so that it does not vibrate against the back ofthe refrigerator or against the wall. Push the refrigerator back to the wall.

• Start the IcemakerSet the ice making stop switch to the ON position The icemaker will not beginto operate until it reaches its operating temperature of 15 °F (-9 °C) or below. Itwill then begin operation automatically if the ice making stop switch is in theON position.

• The automatic ice maker can automatically make 8 pieces of ice cube at a time,80-100 pieces a day.But these quantities may be varied according to various conditions includinghow many times the refrigerator door opens and closes,

• Ice making stops when the ice storage bin is full.

When ice makerdoes not operate

smoothly

CAUTION

Ice is clumped together

• When ice is clumped together, take the ice clumps out ofthe ice storage bin,break them into small pieces, and then place them into the ice storage binagain.

• When the ice maker produces too small or clumped ice, the amount of watersupplied to the ice maker need to adjusted. Contact the service center.

• If ice is not used frequently, it may clump together.

Power failure

• Water may drop into the freezer compartment. Take the ice storage bin out anddiscard all the ice then dry it and place it back.

The unit is newly installed

• It takes about 12 hours for a newly installed refrigerator to make ice in thefreezer compartment.

Throw away the ice (about 20 pieces) first made after refrigerator installation.

The first ice and water may include particles or odor from the feed water pipe orfeed water box.

This is also necessary if the refrigerator has not been used for a long time.

Never store beverage cans or other foods in ice storage bin for the purpose of rapidcooling.

Such actions may damage the automatic ice maker.

Never remove the ice maker cover.

Sometimes level the surface so that the ice storage bin is fully filled with ice.

Ice may pile upjust around the ice maker causing the ice maker to think that the icestorage bin is rul.

If discolored ice is dispensed, immediately contact Service Center.Do not use until problem is solved.

If the freezer

compartment dooris lower than the

refrigeratorcompartment door

If the freezer

compartment dooris higher than the

refrigeratorcompartment door

After leveling thedoor height

Next

Height adjustment

Levelthe door by insertingfiat (- type) driver into the groove of the left height adjustingscrew and rotate it clockwise (0).

Height difference

!

Left height

adjustment screw

Levelthe door by inserting flat (- type) driver into the groove of the right heightadjusting screw and rotate it clockwise (O).

Height differenceI

II _=)II

Right height

adjustment screw

The refrigerator doors will close smoothly by heightening the front side by adjustingthe height adjusting screw. If the doors do not close correctly, performance may beaffected.

1. Wipe off all dust accumulated during shipping and clean your appliance thoroughly.

2. Install accessories such as the ice cube box, cover evaporating tray, etc., in theirproper places.They are packedtogether to prevent possibledamage during shipping.

3. Connect the power supply cord (or plug) to the outlet. Don't double up with otherappliances on the same outlet.

Starting

When your refrigerator is first installed, allow it to stabilize at normal operatingtemperatures for 2-3 hours prior to filling it with fresh or frozen foods.If operation is interrupted, wait 5 minutes before restarting.

Adjusting the temperatures and functions

Water/Ice output

Dispenser push switch

Dew Proofing Switch(When dew is formed

around the Dispenser,turn on the switch.)

Dispenser lamp(Bottom ceiling of

functlbn display board

I Function display board

8

EXPRESSFRZ DISPENSER FREEZERREFRIGERATORFILTERRESET LOCK

[Super freezer.

selection button.

Temperature adjustment buttonfor freezer compartment.

Lock button.

Filter reset button.

Temperature adjustment button

for refrigerator compartment.

How to adjust thetemperature in

the freezer

compartment

How to adjust thetemperature inthe refrigerator

compartment

Dispenser useselection

You can adjust temperature of and freezer room and refrigerator room,

F_eezer room temperatureadjustment

FREEZERSetting

temperature

,_frigerator roomtemperatureadjustment

REFRIGERATORSetting L_IL._°F _._ll °F

temperature

FRZ TEMP FRZ TEMP FRZTEMP FRZTEMP FRZTEMP

_:_Whenever pressing button, setting is repeated in the order of (Middle) ÷(Middle Strong) -_ (Strong) ÷ (Weak)-_ (Middle Weak).

• The actual inner temperature varies depending on the rood status, as theindicated setting temperature is a target temperature, not actual temperaturewithin refrigerator.

• Refrigeration function is weak in the initial time. Please adjust temperature asabove after using refrigerator for minimum 2-3 days.

You can select water or ice.

_:_Please select water, slice ice and square ice by_SPENSER

pressing button as you desire._ Please press the push button lightly by catching and

pushing in cup.• The border line is indicated for the selected function,• "Tak!"sounds if 5 seconds pass after ice comes out.

It is sound that the outlet of ice is closed.

DISPENSER

PressingSwitch

h

• Reference : Please wait for 2-3 seconds in order to take final ice

slices or drops of water when taking out cup from the

pressing switches after taking ice or water.

iiii̧ ii !i

iii_i i

Automatic icemaker

When ice makerdoes not operate

smoothly

Super freezer

Lock

• The icemaker can automatically make 8 pieces of ice cubes at anyone time,approximately 80 pieces per day. However these quantities may vary according tocertain conditions. E.g. the duration and amount of times the refrigerator door isopened.

• The Ice making proceeds ceases automatically when the ice storage bin is full.

• Ifyou choose not to use the automatic ice making function, repositioned theicemaker selection switch to the off position or the on position for reselection. Note:The manual selection function is only applicable to some models only.

Ice is lumped together• When ice is lumped together, take the ice lumps out of the ice storage bin, break

them into small pieces, and then place them into the ice storage bin again.• When the ice maker produces too small or lumped together ice, the amount of

water supplied to the ice maker need to adjusted. Contact the service center.

÷ If ice is not used frequently, it may lump together.

Power failure

• Ice may drop into the freezer compartment. Takethe ice storage bin out and discardall the ice then dry it and place it back. After the machine is powered again, crushedice will be automatically selected.

The unit is newly installed

• It takes about 12 hours for a newly installed refrigerator to make ice in the freezercompartment.

Please select this function for prompt freezer., EXpRESS_RZ

• "On" or "Off" is repeated whenever pressing _button.

• The arrow mark graphic remains at the On statusafter flickering 4times when selecting SpecialRefrigeration "On".

• Super freezer function automatically turns off if afixed time passes.

EXPRESSFRZ

This button stops operation of differentbutton.

• Locking or Release is repeated wheneverLOCK

pressing the (,_ .• Pressing the other button when selecting 'LOCK',

the button does not operate.

LOCK

Ex) In selecting Ex) In selecting"LOCK.... UNLOCK"

The otherfunctions

How ice/cold

water is supplied

How to use

dispenser

Door open warning

• 3 times of warning sounds at the interval of 30 seconds if a minute passes with thedoor of refrigerator and the hombar door opened or completely closed.

• Pleasecontact with the local service center if warning continue to sound even afterclosing the door.

Diagnosis (failure detection) function

• Diagnosisfunction automatically detects failurewhen failure is found in product duringthe use of refrigerator.

• If failure occurs at product, it does not operate though pressing any button and normalindication is not done. In this case, do not turn power off but immediately contact withthe local service center. A lot of time are need for service engineer to detect the failedpart if turning it off.

Water is cooled while stored in the water tank in the refrigerator compartment, andthen sent to the dispenser.Ice is made in the automatic ice maker and sent to the dispenser divided into crushedor cubed form ice.

• Select one among crushed ice, water, and cubed ice and slightly press the pushswitch with a glass or other container.

Water

Light the waterindicating lamp bypressing the selectionbutton.

• Water will be dispensedby pressing the pushswitch with a glass.

DISPENSER

Crushed ice

Light the crushed iceindicating lamp bypressing the selectionbutton.

• Crushed icewill bedispensedby pressingthepushswitchwith aglass.

D,SPE,SER

L

Cubed ice

Light the cubed iceindicating lamp bypressing theselection button.

• Cubedicewill bedispensedby pressing the pushswitch with a glass.

DISPENSER

6 Filter condition

(filter replacementcycle) display

function

Cautions

• After 6 months, the following sentence and will appear on the filter conditionpart of the LEE). "Press for 3 seconds after replacing filter"

• After 6 months have passed, and if the filter has been replaced or you want to reset

the filter condition display, press the filter replacement button for more than 3seconds and it will reset to the initial Power On state.

Throw away the ice (about 20 pieces) and water (about 7 glasses)first madeafter refrigerator installation.The first ice and water may include particles or odor from the feed water pipe or feedwater box. This is necessary in case that the refrigerator has not been used for a longtime.

Keep children away from the dispenser.Children may push switch incorrectly bad or damage lamps.

Be careful that food is not block the ice

passage.If foods are placed at the entrance of icepassage, ice may not be dispensed. The icepassagemay also be covered with icepowder if splinter ice is used only. This time, Freezerdoorremove the ice powder accumulated.

Never store beverage cans or otherfoods in ice storage bin for the purposeof rapid cooling.Such actions may damage the automatic ice maker.

Never use thin crystal glass or crockery to collect ice.Such glasses or containers may be broken.

Put ice first into a glass before filling water or other beverages.Water may be splashed if ice is added to existing liquid in a glass.

Never touch a hand or other tools on ice outlet.

Touch may cause a part breakage or hand injury.

Never remove the ice maker cover.

Sometimes level the surface so that the ice storage bin is fully filled with ice.Ice is piled upjust near the ice maker. So, such status may be considered, by the icemaker, that the ice storage bin is fully filled and ice making operation may stop,

If discolored ice is dispensed, immediately contact service center, stopping use.

Never use too narrow or deep glass.Ice may bejammed in ice passage and, thus, the refrigerator may be failed.

Keep the glass at a proper distance from ice outlet.A glass too close to the outlet may hinder ice from coming out.

Silde-UnderShelf

Wine holder

adjustment

Shelf (Applicableto somemodelsonly)

You can store taller items such as a galloncontainer or bottles by simply pushingin Fronthalf of shelf underneath back half of shelf. Pull toward you to return to aFullshelF.

Wine holder(Applicableto somemodelsonly)

Bottles can be stored laterally with this wine corner. This can be attached to anyshelf,

)

In case of inserting the wine holder :Pull the wine holder downward as in

® aRer inserting it into the side anchoringpart of the shelf as in 0 by catching itupward as in ¢.

In case of separating the wine holder :Pull the wine holder inward as in @ after

holding it upward as in ® by catching it.

!®

l®

Egg box

You can move the egg box to a place you want and select another form of boxaccording to the amount of eggs.

[Normal] [For Many Eggs]

Humidity control in the vegetable compartmentThe humidity carl be controlled by adjusting the humidity control switch to theleft/right when storing vegetabes or fruits.

Highhumidity

I Close I .......... _.......... 0 Open

Lowhumidity

Convert into a vegetable or meat compartment• The bottom drawer in the refrigerator can be converted into a vegetable or meat

compartment

0 Meats Vegetables

,Vegetablecompartment

.0 Meats Vegetables

Meat compartment

The meat compartment maintains the temperature at a lower point than therefrigerator compartment so that meat or fish can be stored fresh longer.

Deodorizer (Applicableto somemodelsonly)

This system efficiently absorbs strong odorsby using the optical catalyst. This systemdoes hot have any affect on stored rood.

f=i

./I./ I

./ I

J_ Deodorizing

systemVegetable

compartment

tl COrnVersion

How to use the

deodorizingsystem

• Since it is installed already installed onto the cool air intake duct from the fromthe refrigerator compartment, you need no separate installation,

• Pleaseuse closed containers to store food with pungent odors,Otherwise, this oder can beabsorbed by other food in the compartment,

Wine holder

Snack drawer

Freezer

compartmentshelf

Freezer

compartmentdoor rack

Freezer

compartmentdrawer

Milk productcorner

Egg box

Refreshmentcenter

Refrigeratorcompartment

shelf

Refrigeratorcompartment

door rack

Vegetable drawer

Vegetabledrawer

/meat drawerconversion corner

Location of foods(Refer to identification of parts)

Store wine.

Store small foods such as bread, snacks, etc..

Store various frozen foods such as meat, fish,ice cream, frozen snacks, etc..

• Store small packed frozen food.• Temperature is likely to increase as door

opens. So, do not store long-term rood suchice cream, etc..

• Store meat, fish, chicken, etc.. afterwrapping them with thin foil.

• Store dry.

Store milk products such as butter, cheese,etc..

Place this egg box in the proper location.

Store foods of frequent use suchas beverage,etc,,

Store side dishes or other foods at a properdistance.

Store small packed rood or beverages suchas milk,juice, beer, etc..

Store vegetables or fruits.

Store vegetable, fruits, meat to thaw, rawfish, etc.. setting the conversion switch asnecessary.Be sure to check the conversion switchsetting before storing foods.

Storing foods

• Store fresh food in the refrigerator compartment. How food is frozen and thawed is animportant factor in maintaining its freshness and flavor.

• Do not store rood which goes bad easily at low temperatures, such as bananas,andmelons.

• Allow hot rood to cool prior to storing, placing hot rood in the refrigerator could spoilother rood, and leadto higher energy consumption.

• When storing the rood, cover it with vinyl wrap or store in a container with a lid. Thisprevents moisture from evaporating, and helps rood to keep its taste and nutrients.

• Do not block air vents with rood. Smooth circulation of chilled air keeps refrigeratortemperatures even.

• Do not open the door frequently. Opening the door lets warm air enter the refrigerator,and cause temperatures to rise.

• Never keep too much rood in door rack because they may push against by innerracksso that the door cannot be fully closed.

Freezer

compartment

Refrigeratorcompartment

• Do not store bottles in the freezer compartment - they may break when frozen.• Do not refreeze food that has been thawed. This causes loss of taste and nutrient.

• When storing frozen rood like ice cream for a long period, place it on the freezershelf, not in the door rack.

• Avoid placing moist food in top refrigerator shelves, it could freeze from directcontact with chilled air.

• Always clean rood prior to refrigeration. Vegetables and fruits should be washed andwiped, and packed rood should be wiped, to prevent adjacent rood from spoiling.

• When storing eggs in their storage rack or box, ensure that they are fresh, and alwaysstore them inan upright position, which keeps them fresh longer.

Freezer

compartmentlamp

Dispenser lamp

Freezer

compartmentshelf

Door rack and

support

Ice storage bin

After dispenseris used

How to dismantle parts

Separatethe lamp by pulling it out (®)whileslightlystriking((1))and rotating ((9)the lampcover,

Turn the bulbcounterclockwise,Max. 40W bulbfor refrigerator is used and can be purchasedata service center.

Seperate the lamp by pulling it out, and thenremove the lamp. Max. 15 W bulb forrefrigerator is used and can be purchased at aservice center.

To remove a shelf, lift the left part of the shelfa bit, push it to the direction (0), lift the rightpart to the diretion (®), and take it out.

Lift the door rack holding both sides ((b) andpull it out to (®) direction.

Hold the ice storage bin as shown inthe rightfigure and pull it out (®) while slightly lifting it(®).• It is recommended not to dismantle the icestorage bin unless it is necessary.

• Be sure to use both hands when removingthe ice storage bin, so as not to drop it on thefloor.

• If the ice storage bin does not fit well, slightlyrotate the rotating device.

The water collector has no self-drainagefunction. So it should be cleaned regularly.Remove the cover by pressing the left side ofwater collector cover and dry it with a cloth.Press the point marked as shown in the figureto the right to remove the water collectorcover.

y devicteng

Lamp inrefrigerator

compartment

Vegetablecompartment

cover

To remove the lamp cover, press the protrusion under the lamp cover to the front andthen pull the lamp cover out.Turn the bulb counterclockwise. Max. 40 W bulb for refrigerator is used and can bepurchased at a service center.

• To remove the vegetable compartment

cover, pull out the vegetable compartment

a bit to the front (b, lift the front part of thevegetable compartment cover as shown by

@, and take it out.

®

Vacation time

Power failure

If you move

Anticondensation

pipe

Exterior

Interior

After cleaning

Warning

General information

During average length vacations, you will probably find it best to leave the refrigeratorin operation. Placefreezable items in freezer for longer life.When you plan not to operate, remove all food, disconnect the power cord, clean theinterior thoroughly, and leave each door OPEN to prevent odor formation.

Most power failures that are corrected in an hour or two will not affect yourrefrigerator temperatures.However, you should minimize the number of door openings while the power is off.

Remove or securely fasten down all loose items inside the refrigerator.To avoid damaging the height adjusting screws, turn them all the way into the base.

The outside wall of the refrigerator cabinet may sometimes get warm, especiallyjustafter installation.Don't be alarmed. This is due to the anti-condensation pipe, which pumps hotrefrigerator to prevent "sweating" on the outer cabinet wall.

CleaningIt is important that your refrigerator be kept clean to prevent undesirable odors. Spilledrood should be wiped up immediately, since it may acidify and stain plastic surfaces ifallowed to settle.

Use a lukewarm solution of mild soap or detergent to clean the durable finish of yourrefrigerator.Wipe with a clean damp cloth and then dry.

Regular cleaning is recommended. Wash all compartments a baking soda solution or amild detergent and warm water. Rinse and dry.

Please verify that the power cord is not damaged, power plug is not overheated, orpower plug is well inserted into the power consent.

Always remove power cord from the wall outlet prior to cleaning in the vicinity ofelectrical parts (lamps, switches, controls, etc.).Wipe up excess moisture with a sponge or cloth to prevent water or liquid fromgetting into any electrical part and causing an electric shock.Never use metallic scouring pads, brushes, coarse abrasive cleaners, strong alkalinesolutions, flammable or toxic cleaning liquids on any surface.Do not touch frozen surfaces with wet or damp hands, because damp object will stickor adhere to extremely cold surfaces.

Trouble shooting

Before calling for service, review this list. It may save you both time and expense,This list includes common occurrences that are not the result of defective

workmanship or materials in this appliance.

Runing ofrefrigerator

Refrigerator Refrigerator control is off. Set refrigerator control. See setting thecompressor controls.

does not run. Refrigerator is in defrost cycle. This is normal for a fully automaticdefrosting refrigerator. The defrostcycle occurs periodically.

Plug at wall outlet is disconnected. Make sure plug is tightly pushed intooutlet.

Power outage. Check house lights. Call local electric company.

Refrigerator Refrigerator is larger than the previous This is normal. Larger, more efficientruns too much one you owned, units run longer in these conditions.

or too long Room or outside weather is hot. It is normal for the refrigerator to worklonger under these conditions.

Refrigerator has recently been It takes some hours for the refrigeratordisconnected for a period of time. to cool down completely.

Large amounts of warm or hot food Warm food will cause the refrigerator tomay have been stored recently, run longer until the desired temperature

is reached.

Doors are opened too frequently or too Warm air entering the refrigeratorlong. causes it to run longer. Open the door

less often.

Refrigerator or freezer door may be Make sure the refrigerator is level.slightly open. Keep food and containers from

blocking door. See problem section.OPENING/CLOSING of doors.

Refrigerator control is set too cold. Set the refrigerator control to awarmer setting until the refrigeratortemperature is satisfactory.

Refrigerator or freezer gasket is dirty, Clean or change gasket. Leaks in theworn, cracked, or poorly fitted, door seal will cause refrigerator to run

longer in order to maintain desiredtern peratures.

Thermostat is keeping the refrigerator This is normal. Refrigerator goes on andat a constant temperature, off to keep the temperature constant,

Refrigerator Thermostat is keeping the refrigerator This is normal. The refrigerator goes oncompressor at a constant temperature, andoffto keep the temperature constant,

does not run.

Temperatures aretoo cold

Temperature in the Freezer control is set too cold Set the Freezercontrol to a warmerfreezer is too cold setting until the Freezertemperature isbutthe refrigerator satisfactory.

temperature issatisfactory.

Temperature in the Refrigerator control is set too cold. Set the refrigerator control to arefrigerator is too warmer setting

cold and the freezertemperature

is satisfactory.

Food stored indrawers freezes. Refrigerator control is set too cold. See above solution.

Meat stored in Meat should be stored at a temperature It is normal For ice crystals to Form duefresh meat just below the freezingpoint of water (32°F, to the moisture content of meat.

drawer freezes. OC) for maximum fresh storage time.

Temperaturesare too warm

Temperatures in Freezer control is set too warm. Set the Freezeror refrigerator control tothe refrigerator a colder setting until the Freezeror

or freezer are refrigerator temperature is satisfactory.too warm. ......

ReFrigeratorcontrol is set too warm. Set the freezer or refrigerator control to aRefrigerator control has some effect on colder setting until the freezer orfreezer temperature, refrigerator temperature is satisfactory.

Doors are opened too Frequently or too Warm air enters the refrigerator/freezerlong. whenever the door is opened.

Open the door less often.

Door is slightly open. Close the door completely.

Large amounts of warm or hot food Wait until the refrigerator or freezermay have been stored recently, has a chance to reach its selected

temperature.

Refrigerator has recently been A refrigerator requires some hours todisconnected for a period of time. cool down completely.

Temperature in the Refrigerator control is set too warm. Set the refrigerator control to a colderrefrigerator setting.

is too warm butthe freezer

temperature issatisfactory.

Sound and noise

Louder sound Today's refrigerators have increased It is normal for sound levels to be higher.levelswhen storage capacity and maintain more

refrigerator is on. even temperatures.

Louder sound Refrigeratoroperates at higher pressures This is normal. The sound will level off aslevels when during the start of the ON cycle, the refrigerator continues to run.compressor

comes on.

Vibrating or Floor is uneven or weak. Be sure floor is level and solid and canrattling noise. Refrigerator rocks on the floor when it is adequately support refrigerator.

moved slightly.

Items placed on the top of the refrigerator Remove items.are vibrating.

Dishes are vibrating on the shelves in It is normal for dishes to vibrate slightly.the refrigerator. Move dishes slightly.

Make sure refrigerator is level and firmlyset on floor.

Refrigerator is touching wall or cabinets. Move refrigerator so that it does nottouch the wall or refrigerator.

Water/Moisture/Ice inside

refrigerator

Moisture collects The weather is hot and humid which This is normal.on the inside walls increases the rate of frost buildupof the refrigerator, and internal sweating.

Door is slightly open. See problem section opening/closing ofdoors.

Door is opened too often or too long. Open the door less often.

Water/Moisture/Ice outside

refrigerator

Moisture forms Weather is humid. This is normal in humid weather.on the outside of When humidity is lower, the moisture

the refrigerator should disappear.or between doors.

Door is slightly open,causing cold air This time, close the door completely.from the inside the refrigerator to meetwarm air from the outside.

Odors in refrigerator

Interior needs to be cleaned. Clean interior with sponge,warm waterand baking soda.

Food with strong odor is in the refrigerator. Cover rood completely.

Some containers and wrapping materials Use a different container or brand ofproduce odors, wrapping materials.

Opening/Closing ofdoors/Drawers

Door(s) will not Food package is keeping door open. Move packages that keep door fromclose, closing.

Door(s) will not Door was closed too hard, causing other Close both doors gently.close, door to open slightly.

Refrigerator is not level. It rocks on the Adjust the height adjusting screw.floor when it is moved slightly.

Floor is uneven or weak. Be sure floor is level and can adequatelyRefrigerator rocks on the floor when it support refrigerator.is moved slightly. Contact carpenter to correct sagging or

sloping floor.

Refrigerator is touching wall or cabinets. Move refrigerator..

Drawers are Food is touching shelf on top of the Keep less rood in drawer.difficult to move. drawer

Track that drawer slides on is dirty. Clean drawer and track.

Dispenser

Dispenser will not Ice storage bin is empty. When the first supply or ice is droppeddispense ice into the bin, the dispenser should operate,

Freezer temperature is set too warm. Turn the freezer control to a highersetting so that ice cubes will be made,When the first supply of ice is made,the dispenser should operate.

Household water line valve is not open. Open household water line valve andallow sufficient time Forice to be made.When ice is made, dispenser shouldoperate.

Refrigerator or freezer door is not closed. Be sure both doors are closed.

Dispenserwill IcehasmeltedandFrozenaroundauger Removeicestoragebin,andthawandnot dispense due to infrequent use, temperature the contents. Clean bin, wipe dry and

ice. Fluctuations and/or power outrages, replace in proper position.When new ice is made, dispenser shouldoperate.

Ice dispenser Icecubes arejammed between the ice Remove the ice cubes that arejammingis jammed, maker arm and back oFthe bin. the dispenser.

Icecubes are Frozentogether. Use the dispenser often so that cubes donot Freezetogether.

Icecubes that have been purchased or Only the ice cubes made by the ice makermade in some other way have been should be used with the dispenser.used in the dispenser.

Dispenser will Household water line valve is not open. Open household water line valve.not dispense See problem "Ice maker is not making

water, any ice."

ReFrigeratoror Freezerdoor is not closed. Be sure both doors are closed.

Water has an Water has been inthe tank Fortoo long. [)raw and discard 7 glasses oFwaterodd taste to Freshenthe supply. [)raw and discard

and/or odor. an additional 7 glasses to completely rinseout tank.

Unit not properly connected to cold Connect unit to cold water line whichwater line. supplies water to kitchen Faucet.

Sound of ice This sound is normally made when automatically made ice is dropped into ice storagedropping bin. Volume may vary according to refrigerator's location.

Sound of water This sound is normally made when ice maker is supplied with water after droppingsupply the automatically made ice.

Other Pleasethoroughly read 'Automatic ice maker and dispenser' in this manual.

LG Electronics Inc.

LG Twin Tower, 20, Yoido-Dong,Youngdungpo-Gu, Seoul, 150-721, Korea.http://www.lge.com

P/NO : 3828JD8632Z Printed in Korea