cubicle curtain track shop drawing for reference

8/10/2019 Cubicle Curtain Track Shop Drawing for Reference

1/22

Transmittal

Date: July 22, 2013

To: Steve Busen, LEED APSkanska

26100 American DriveSuite 200Southfield, Michigan 48034-2367

From: Shannon Shackelford

Project: Cardiovascular Institute and Harper-Hutzel Specialty CenterDetroit Medical Center,Detroit, Michigan

Project No: 2011-10001-000

Owner Project No:

Sent Via: Electronic E-Builder Site For your: Use/Records

Distribution: Jones Lange LaSalleAndrea Burg

JenkinsConstruction, Inc.James Robinson


2/22

SUBMITTAL LABEL

PROJECT NO: 2011-10001-000

PROJECT Cardiovascular Institute and Harper-HutzelSpecialty Center

Detroit Medical CenterDetroit, Michigan

DATE July 9, 2013

CONTRACTOR/SUPPLIER Jenkins/Skanska

DESCRIPTION Product Data/Shop Drawing

Cubicles - Curtain TrackJ/S Reference No. 0823

SPECIFICATION NO. 102123

COMMENTS


3/22


4/22

C/S Cubicle Curtains

SHOP DRAWING TRANSMITTAL

FOR APPROVAL ONLY - FABRICATION PENDING RELEASE

Date: 07 /03 / 2013

ATTN: JEFFREY M. STONE

RE: DMC CARDIOVASCULAR INSTITUTE

C/S ORDER NO: 998190

YOUR PO: SQ130006

Dear Customer,

Construction Specialties, Inc.

107 Johnson Blvd.Del Rio, TX 78840

Sales (908) 325-4900

Customer Service: (908) 849 4750Customer Service Fax: (908) 849-4399

www.c/sgroup.com

PONTIAC CEILING & PARTITION

715 AUBURN RD

PONTIAC, MI 48342


5/22

Re: SUBMITTALS

Please find the following items enclosed:

1 SHOP DRAWING COPIE

2 TRACK SAMPLES WITH ACCESSORIES:SATIN ANODIZED

2 IV TRACK SAMPLES:SATIN ANODIZED

If you should have any questions please contact me.

Thank you

Not included in this submittal.


6/22

Warranty


107 Johnson Blvd.

Del Rio, TX 78840

Sales (908) 325-4900

Customer Service: (908) 849-4750Customer Service Fax: (908) 849-4399


7/22

Maintenance


107 Johnson Blvd.

Del Rio, TX 78840

Sales (908) 325-4900

Customer Service: (908) 849-4750

Customer Service Fax: (908) 849-4399


8/22

* Drawing not to

scale

SMCCT #6062

The C/S Cubicle Curtain track is Dual Channel, extruded aluminum track

made from aluminum alloy in a anodized or white baked enamel. Trackdimensions are 1 3/8" x 3/4" deep (see below) with a minimum wall.

SURFACE MOUNTED

CUBICLE CURTAIN TRACK


9/22

Specification for Surface Mounted Cubicle Track

PART 2 PRODUCTS

2.01 ACCEPTABLE MANUFACTURERS

A. General: Cubicle Track system shall be complete as specified in this section and manufactured byCubicle Curtains, Cranford, NJ.

B. Substitutions: Other manufacturers are acceptable for evaluation only after compliance with Section

01630.


10/22

ConstructionSpecialt

107Johns

DelRio,T

Sales 908)3

CustomerService: 908)8

CustomerServiceFax: 908)8

INSTALLATION INSTRUCTIONS FOR CEILING-MOUNTED CUBICLE TRAC

C/S G E N E R A L C U B I C L E

Attached is a copy of our Tally Sheet, which lists all items required for individual rooms. The totals shown on this list shou

be used to check items received in shipment. Reports of shortages will not be accepted if made after (5) days after shi

ment has been received.

Large Bends (8'x8') will be furnished only where a project is large enough to offset the cost of crafting these bends. Whe

this is not permissible, Small Bends (2'x2') will be furnished with Splices and proper lengths of track - to be joined to th

Small Bends.

Measurements of Large Bends is approximately 8' 2 " x 8' 2 ". These will be shipped this way, to be cut on the job. F

proper installation, follow "Shop Drawing" for lay-out, if parts shipped were based on this.

1. Mark ceiling lightly where track is to be installed. Drill track at proper intervals. Start at the

center point of radius, and drill every 3' 0" on both directions. NOTE: Drill must be in perfect center

of track! When drilling ends of track, affix stops and gates and drill through these.

2. Prop track against ceiling with boards. Mark ceiling through drilled holes. Remove

track and drill through ceiling. (Size of drill to be determined by type of fastenersyou are using.) NOTE: If track is to be mounted against wood backings, then keep

tracking against ceiling, drill "guide hole" through ceiling, and then use proper

length of Wood Screws for a strong hold.

3. Head of fasteners should be pan-head - not to exceed Size No. 8


11/22


12/22


13/22


14/22


15/22

Specification for Surface Mounted IV Track

PART 2 PRODUCTS

2.01 ACCEPTABLE MANUFACTURERS

A. General: IV Track system shall be complete as specified in this section and manufactured by

Cubicle Curtains, Cranford, NJ.

B. Substitutions: Other manufacturers are acceptable for evaluation only after compliance with

Section 01630.

2.02 IV TRACK SYSTEM

A. I.V. Tracks: Cubicle Curtains I.V. track model #17000. Surface-mounted tracks of heavy

extruded aluminum alloy 6063-T5, 1 " x ", slotted to receive twist lock I.V. Carrier,

compete with accessories and components required for complete and secure installations

including splicers, end caps and corner bends.

1. Finish: Satin Anodized.

B C i C bi l C i 17500 T i L k I V C i C i h i h ll b


16/22

Surface Mounted I.V TackThe C/S General Cubicle I.V Track is dual channel, extruded aluminum track

Made from aluminum alloy in baked white enamel.

Aluminum I.V Carrier Stop # 162(W)

17500 TWIST LOCK

I.V. CARRIER


17/22

49 Meeker Avenue

Cranford, NJ 0701Tel: (908) 849-474Fax: (908) 849-439

MODEL# 17150

Fabricated of polished stainless steel this unit has a " diameter

tubing for the main shaft, 3/8" diameter for the inner shaft, and four

folding " diameter spiral safety arms plus one additional hook in the

bottom as the fifth holder.

DELUXE 5 BOTTLE I.V. PENDANT


18/22


19/22


20/22

Confirm assignedscope. Only curtains

are not construction

scope responsibility.

Yes


21/22


22/22

41030A

P/R 1 ISO

cubicle curtain track shop drawing for reference

Documents