STEP BY STEP CONFIGURATION OF D-LINK DRO – 250i ROUTER

1. IMPLEMENTING THE D-LINK ROUTER:

Connect the D-Link Router’s LAN Port to the PC using Cross Cable

Set the PC’s TCP/IP in DHCP Mode (i.e. Obtain an IP address automatically)

Disable the Proxy Server IP in IE Browser

The Default LAN IP of D-Link Router is 192.168.100.254

Browse the following address https://192.168.100.254

It will ask for Username and Password

Default Username and password is admin.

2. CONFIGURATION OF LAN IP:

Click on Interface > LAN, change the IP address , Mask to the Particular Range and then give Apply --- OK

After

Changing the LAN IP in the Router, your Browser page will be disconnected.

Change the IP address of your PC to the LAN block Range

Browse the following address

https://<LAN IP>

3. CONFIGURATION OF WAN IP

Click on Interfaces > WAN1, change the IP, Mask and Gateway that is provided by the MPLS NOC, the Protocol should be Cisco HDLC, after that give Apply --- OK

IP Settings for WAN1 Interface

WAN1 Protocol

IP address  (Number)

Subnet Mask 

Default Gateway 

 

4. ROUTING:

LAN Settings IP address 

Subnet Mask 

 

Click Routing, select the Routing Protocol to be Static, the Interface Name to be LAN, the Destination and Subnet should be 0.0.0.0, the Gateway should be Disable and then give Apply --- OK

Static Routing     

Routing Protocol  View Active Routes

Add/Edit Static Routing IP 

Interface Name

Destination Network IP address 

Subnet Mask 

Gateway IP address  (Disable)

Route Entries                                                                             Maximum Entries: 50

Destination IP address Subnet Mask Gateway IP address Interface Delete

0.0.0.0 0.0.0.0 0.0.0.0 WAN1

Page 1

5. DISABLING THE DHCP SERVER IN ROUTER:

Click on Advanced > DHCP> DHCP Server, mark DHCP Server Status to be Disable and then give apply --- OK --- OK --- OK

DHCP Server

DHCP Server Status Enable Disable

Starting IP address 

Ending IP Address 

Default Gateway 

Lease Time (sec)

Auto Configuration Enable Disable

Domain Name

Primary DNS Server 

Secondary DNS Server  (Option Disable)

 

6. SAVING ALL CONFIGURATIONS TO FLASH:

Click on Tools > System and then give Save --- OK --- Continue

System Settings

Save Settings............................................

Save Settings and Restart Device............

Restore to Factory Default Settings..........

Restart the Device....................................

The entire Configuration done in the Router will be saved to flash.

Disconnect the Cross Cable from PC & Router’s LAN Port

7. OTHER DETAILS:

Connect the V.35 DTE WAN 1 Interface to the Modem Browse the following address

https://<LAN IP> Click on Status > Device Info and check for the

Interface Status

Device Information Device Name DRO-250i

Firmware Version 2.0.5

System Up Since 0 days 0 hours 4 minutes 24 seconds

LAN

LAN Status UP MAC Address 00:17:7c:00:01:87

IP address10.192.10.6

Subnet Mask 255.255.255.0

DHCP Server Disabled

WAN 1

WAN1 Status UP IP address 10.194.144.18

Subnet Mask 255.255.255.252

Default Gateway 10.194.144.17

WAN 2

WAN2-B1 Status DOWN WAN2-B2 Status DOWN Status Click Here for WAN2 Info WAN3

WAN3Status DOWNMAC Address 00:17:7c:00:01:88

Connection Type Static

IP address 10.1.1.254

Subnet Mask 255.255.255.0

Default Gateway 10.1.1.253

WAN 4

WAN4 Status DOWN Status Click Here for WAN4 Info

Click on Tools > Ping Test and do the necessary ping test from Router

@@@@@ THE END @@@@@

For Further Clarification, Contact

RAMPRAKASH = 9994303320 PERUMAL = 9841445663

Ping Test   Set Type 

IP Address

Domain Name

Count number <= 10