- +MODE

D10 W RFWireless thermostat forheating control

Installation instructions

Delta Dore hereby declares that the equipment complies with the essential requirements and other relevant provisions

of the R&TTE Directive 1999/5/EC.

The EC declaration of conformity for this equipment is available, on request, from:

“Technical info” departmentDELTA DORE - Bonnemain - 35270 Combourg (France)

Email: info.techniques@deltadore.com

Because of changes in standards and equipment, the characteristics given in thetext and the illustrations in this document are not binding unless confirmed.

*2702706_rev.1*

• Carefully read these instructions prior toinstallation.

• The unit must be installed in compliance withcurrent standards.

• Always switch off the mains before installing orservicing the unit.

• Do not attempt to repair the unit yourself; after-salesservice is available.

• Check that the fastenings are suitable for thesurface to which the unit will be mounted (plasterboard, brick, etc.).

• The diagrams provided are simplified for greaterclarity.Protections and other accessories required bystandards are not illustrated.Standards and good practice must be compliedwith. Connected or nearby units must notgenerate excessive interference (Directive2004/108/EC).

1. Installing the RF 810 receiver

2. Connecting the RF 810 receiver

N L 1 2 3 4230V~

50-60 Hz3A max. / 230V~

2721

318

Rev

.1

CHOFF

CHON

Cons. 11 VAP = 1,2 W

N L 1 2 3 4230V~

50-60 Hz3A max. / 230V~

2721

318

Rev

.1

CHOFF

CHON

Cons. 11 VAP = 1,2 W

23

4

1

5

6

Technical characteristics

Transmitter D10 RF• Power supply: 2 LR03-AAA type 1.5 V alkaline batteries• Insulation class: class III • Transmission frequency 868 MHz (Standard EN 300 220)• Class 1 radio equipment (can be placed on the market and

put into service without any restrictions)• Radio range: 100 to 300 metres outside, varies depending on

the equipment linked (the range can be altered depending onthe installation conditions and the electromagneticenvironment)

• Wireless remote control device• PI (Proportion Integral) regulation• Storage temperature: -10 °C to +70 °C• Operating temperature: 0 °C to +40 °C• Dimensions: 80 x 80 x 23 mm• Protection rating: IP30• Installation in an environment with normal pollution levels

Receiver RF 810• 230 V, 50 Hz power supply, +/-10%,• Consumption: 11 VA (P=1.2 W)• Class II insulation• Contact output 3 A max., 230 V Cos ϕ = 1• Automatic action: 1.C (brownout),• Radio frequency 868 MHz (standard EN 300 220)• Wireless range: 100 to 300 metres outside, variable

depending on the associated equipment (the range can varydepending on the installation conditions and theelectromagnetic environment)

• Storage temperature: -10 °C to +70 °C• Operating temperature: 0 °C to +40 °C• Installation in an environment with normal pollution levels• Screw mounting (standard Wallplate)• Dimensions: 96 x 96 x 39 mm• Protection rating: IP 40

N L 1 2 3 4230V~

50-60 Hz3A max. / 230V~

CHOFF

CHON

NL

N L 1 2 3 4230V~

50-60 Hz3A max. / 230V~

CHOFF

CHON

NLCirculator pump

Example 1230V powered output

Example 2Dry contact output

Boilerthermostat

input

~1,50 m

Mini 20 cm

AA

B

B

1

1

2

2

3

4

5

6

3. Positioning the Radio D10

6. Troubleshooting

Nothing is displayed on the transmitter screen.There is no power supply.Check the batteries.

No LEDs light up on the receiver.The receiver is not powered.Check the receiver’s electrical connections.

The receiver does not accept commandsfrom the transmitter.• The transmitter is not associated with the

receiver.Repeat the association procedure.

• The transmitter batteries are low.Change the transmitter batteries.

• Radio transmission is not optimal.Transmission quality depends on the installation conditions and environment (type of wall, location, etc.).

The icon appears.Battery level is low.Change the batteries, ensuring they are in thecorrect position.

5. Configuring the Radio D10

4. Associating the Radio D10 transmitter with the receiver

- +MODE

> 3"

> 3"

1 2 3

- +MODE

5

OK

... ... ...

- +MODE

MODE

6+

- +MODE

7 8

9

+

- +MODE

4

- +MODE

> 10"

+ 0,5°C

- 0,5°C1MODE

MODE

+- +MODE

2 3

+

-- +MODE

4 5

MODE

- +MODE

6+

7MODE

- +MODE

8MODE

- +MODE

9

+

Continuous display of theroom temperature

Continuous display of thetemperature setting

Correcting thetemperature measured(-5 °C to +5 °C)

Keypad unlockedMandatory

Keypad locked(settings, mode)

The transmitter and the receiver are associated when delivered.You may however need to reassociate your products (after removing wireless associations for instance).

NOTE: You can manually reset the receiver by pressing thebutton of the channel to associate for 10 seconds until theLED flashes rapidly.