dashboard / instrument panel: service and repair … loosening the mounting screw, then remove the...

2012 Kia Truck Sorento 4WD V6-3.5L Copyright © 2013, ALLDATA 10.52

Dashboard / Instrument Panel: Service and RepairRepair Procedures

Replacement

Cluster Fascia Panel Replacement

NOTE:- When prying with a flat-up screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.- Put on gloves to protect your hands.

1. Using a screwdriver, remove the crash pad side cover (A).

2. After loosening the mounting screws, then remove the crash pad lower panel (A).3. Disconnect the diagnosis connector (B).

4. After loosening the mounting screws, then remove the side garnish (A).


5. Push the lock pin (A), disconnect the connectors.

6. After loosening the mounting screw, then remove the cluster fascia panel (A).

7. After loosening the mounting screws, then remove the cluster (A).

8. Push the lock pin (A), disconnect the connectors (B).


9. Installation is the reverse of removal.

NOTE:- Make sure the connector is plugged in properly.- Replace any damage clips.

Center Fascia Panel Replacement


1. Remove the floor console upper cover (A).

2. Remove the center fascia lower panel (A).



4. After loosening the mounting screws, then remove the center fascia panel (A).

5. Push the lock pin, disconnect the connector (A).

6. Installation is the reverse the removal.

NOTE:- Make sure the connector is plugged in properly.

Lower Panel Replacement1. Remove the crash pad side cover (A).


2. After loosening the crash pad lower panel mounting screws, remove the lower panel (A).3. Push the lock pin (B), disconnect the diagnosis connector (C).

4. After loosening the mounting bolts, then remove the reinforce panel (A).


Audio Assembly Replacement1. Remove the floor console upper cover (A).


2. Remove the center fascia lower panel (A).


4. After loosening the mounting screws, then remove the center fascia panel (A).

5. Push the lock pin, disconnect the connector (A).


6. After loosening the mounting screws, then remove the heater control unit (A).

7. After loosening the mounting screws, then remove the audio assembly (A).



Glove Box Replacement1. Using a screwdriver or remover, remove the crash pad side cover (A).


2. Disconnect the guide (B), from the glove box (A).

3. Disconnect the damper (B), from the glove box (A).

4. Disconnect the pin (A), then remove the glove box (B).


5. After loosening the mounting screws, then remove the crash pad side garnish (A).

6. After loosening the mounting screws, then remove the crash pad lower cover (A).

7. After loosening the mounting screws, then remove the glove box housing (A).



Shroud Replacement1. After loosening the mounting screws, then remove the shroud assembly (A).


Crash Pad Side Cover Replacement


1. Using a screwdriver, remove the crash pad side cover (A).


Main Crash Pad Replacement

CAUTION:- When prying with a flat-up screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.- Put on gloves to protect your hands.

1. Remove the following items.A. Front seat.B. Cluster.C. Audio assembly.D. Glove box.E. Crash pad side cover.F. Front pillar trim.


2. Disconnect the lock pin, disconnect the passenger`s air bag connector (A).3. Loosen the mounting bolts.

4. After loosening the mounting bolts and nuts, then remove the crash pad (A).5. Disconnect the photo sensor connector mounting clip.6. Disconnect the auto light sensor connector mounting clip (B).


NOTE:- Make sure the crash pad fits onto the guide pins correctly.- Before tightening the bolts, make sure the crash pad wire harnesses are not pinched.- Make sure the connectors are plugged in properly, and the antenna lead is connected properly.- Enter the anti- theft code for the radio, then enter the customer`s radio station presets.

Cowl Cross Bar Assembly Replacement1. Remove the following items.

A. Floor console.B. Crash pad.C. A/C hose. D. Heater hose. E. Cowl top cover.

2. Push the lock pin (A), disconnect the driver`s wiring connectors.


3. Disconnect the passenger's wiring connectors.

4. Disconnect the cap, loosen the mounting bolt.5. Remove the pedal (A).

6. Remove the floor mat, then disconnect the air bag connector (A).7. Loosen the mounting bolt (B).


8. After loosening the mounting screws, then remove the air duct (A).

9. After loosening the mounting screws, then remove the duct (A).

10. After loosening the mounting screws, then remove the air duct (A).

11. After loosening the mounting bolts, then remove the cowl cross bar (A).



NOTE:- Put on gloves to protect your hands.- Make sure the connectors are plugged in properly.

dashboard / instrument panel: service and repair … loosening the mounting screw, then remove the...

Documents