AT-200YData Sheet

Economical multi-purpose sealant tape

ZI Haneboesch

L-4562 Differdange

LUXEMBOURG

Phone : +352 58 22 82 1Fax : +352 58 49 35

E-mail : sales@airtech.luWebsite : www.airtech.lu

Last updated : 2016-07-29

Catalogue position : Vacuum bag sealant tapesAs the conditions or methods of use, including storage, are beyond our control, Airtech Europe does not assume any responsibility for the performance of this material for any particular use. The material is sold "as is".

Airtech Europe disclaims, and buyer waives, any and all implied warranties, including without limitation the implied warranties of merchantability and of fitness for particular use. The information contained herein

represents typical properties and should not be used for specification purposes. This translation is provided for your convenience only. The official language is English and the official law is Luxembourg.

DESCRIPTION

AT-200Y is an economical multi-purpose sealant tape with high tack. It removes easily from metal or compositetools. Suitable for cure applications up to 204°C.

BENEFITS

• Economical vacuum tape reduces the cost of vacuum bagging.• Multi-purpose tape can be used on metal and composite tooling.• Easy clean up reduces cost of tool cleaning.

TECHNICAL DATA

Colour Yellow

Base material Synthetic rubber

Maximum use temperature 204°C

Shelf life 12 months from date of manufacture

Storage conditionsTape must be stored flat in original packaging at 22°CDo not refrigerate

SIZES

Dimensions Packaging

3 mm x 12 mm x 7,5 m(1/8 inch x 1/2 inch x 25 feet)

40 rolls per case

3 mm x 19 mm x 7,5 m(1/8 inch x 3/4 inch x 25 feet)

28 rolls per case

NOTES

• For clean removal, it is recommended to strip the tape from the mould surface once it has cooled down to  room temperature.• The maximum use temperature is dependent upon the duration at maximum temperature and is process  specific, Airtech recommends testing prior to use.

SecurSeal EDGE SEAL

SS-3199ES

A

NOTE: It is advisable to wipe the edge of the

laminate with isopropyl alcohol prior to applying

SecurSeal to remove anything finger oils, etc.

that may interfere with the bond.

SecurSeal (SS-3199ES) edge seal is a unique multi-layer polyurethane product specifically designed as

a protective membrane when laminated to the edge of a transparency.

SecurSeal (SS-3199ES) edge seal is a multi-layer

edge sealing polyurethane. The multi-layer

construction of the edge seal is (A) a diamond

pattern embossed polypropylene carrier. This carrier

will be removed following lamination. (B) is a layer of

proprietary black polyurethane. (C) is a clear layer of

aliphatic polyurethane which will permanently bond

to the edge of the laminate. All polyurethanes used

in SecurSeal are light stable aliphatic formulations.

Lamination Information:

SecurSeal (SS-3199ES) requires a minimum

lamination temperature of 195°F (90°C).

SecurSeal (SS-3199ES) edge seal is currently

available in many widths. (9mm - 1 meter)

Custom slit widths are available upon request or

SecurSeal is available in "Master" rolls [ 40"(1 meter)

x 120'(36.5m) ].

SecurSeal (SS-3199ES) does not require any specific

storage or handling. Keeping it clean and dry will

insure usable product.

SecurSeal (SS-3199ES) Storage and Handling

Average Peel

1 0-(gm/1 00in2/day)

ASTM-01238

5.0g / 10min. @ 177°C ASTM 03167 > 150 pli

Test Method

ASTM 0412

Value

763%

5130psi

Property

Ultimate Elongation

Tensile

Melt Index

Typical Physical Properties

SecurSeal (SS-3199ES) is a multi-ply film product designed to protect,

prevent moisture and solvent migration, and camouflage the edges of a

security transparency.

Specifications

Units

Values

Clear

Values

Black

Durometer ASTM D2240 75A 87A

Specific Gravity: ASTM D792 1.07 1.12

Thermal Properties

Maximum Service

Temperatures,

-continuous °F -65° to 160° -60° to 200°

SecurSeal EDGE SEAL

SS-3199ES

SecurSeal(SS-3199ES)Edge Seal must be used in conjunction with vacuum bag lamination.

SecurSeal (SS-3199ES), after autoclaving, will impart an attractive diamond pattern into the edge seal.

Following lay-up of your transparency:

1...Apply the SecurSeal (SS-3199ES) to the edge of the

laminate.

2...Secure the SecurSeal (SS-3199ES) where the ends meet by

means of tape.

3...Vacuum bag and laminate as you normally would.

4...Upon completion of the autoclave lamination allow the

laminate to cool to room temperature before extracting the

laminate from the vacuum bag.

5...Following the removal of the vacuum bagging and all

breather materials, remove the diamond pattern polypropylene

film from the SecurSeal (SS-3199ES) to expose the black

polyurethane edge seal product.

Process Information

°C -54° to 71° -51° to 193°

-melting point range °F

°C

248° to 284°

120° to 140°

340° to 380°

171° to 193°

Tensile Properties: ASTM D638

Modulus @ 100% Strain psi 500 1000

Modulus @ 300% Strain psi 1500 2000

Modulus @ Break psi 5000 7000

Elongation @ Break % 375 450

Set @ Break % 5 35

Tear Properties:

Die C ASTM D624 pli 300 400

Moisture Vapor

Transmission Value ASTM E96 10-20g/m²/24 hrs.

3M Commercial Graphics

3M Center

St. Paul, MN 55144-1000

General 1-800-374-6772

Product Flammability Information

The attached ASTM E-84 is for Scotchgard™ Removable Graphic and Surface Protection Film 8991R. Due to similar film construction, we expect Scotchgard™ Graphic and Surface Protection Film 8991 to have comparable results to Scotchgard™ Removable Graphic and Surface Protection Film 8991R.

After a material is subjected to the ASTM E-84 test, it is given a rating based on its performance

during the test. Materials are classified into one of three groups based on their tested flame

spread characteristics. These groups and their flame spread indexes are listed below:

Class Flame Spread Index

I (A) 0-25

II (B) 26-75

III (C) 76-200

Class I or (A) rating means it is the most fire resistant category that NFPA recognizes as

necessary for interior wall and ceiling finish materials. It will be acceptable in any building in

any locality that models its building code after NFPA 101 for wall or ceiling materials.

NFPA 101 is a code that provides minimum requirements for the design, operation and

maintenance of building and structures for safety to life from fire and similar emergencies. The

requirements differ depending on the type of building.

Many building codes require a smoke developed rating of 450 or less for building materials. The

Scotchgard™ Removable Graphic and Surface Protection Film 8991R meets the requirements of Class I (A) and the smoke developed rating of less than or equal to 450.

If you have any questions about the features or performance of this 3M product, please call

Commercial Graphics Division Technical Service at 1-800-328-3908.

Sincerely,

3M Commercial Graphics Product Responsibility

QUALITY DEPARTMENT

High Optical Quality Specifications

Type Black Specs,

Inclusions, Bubbles, Coating defects Actual defect size excl. Halo (mm/in)

Defect size including

Halo (mm/in) Lint, Fibers & Scratches Width max 0.5mm (0.020”) Length in mm/in

Max number of

defects allowed Dimension test sample

mm inches mm inches mm inches cm inches

A ≤ 0.25 0.010 < 0.25 0.010 < 0.50 0.020 Allowed 100 x 100 39.37 x 39.37

B ≥ 0.25 – 0.50 0.010 – 0.020 < 0.50 0.020 ≥ 0.50 – 5.00 0.020 – 0.200 10 100 x 100 39.37 x 39.37

C ≥ 0.51 – 1.00 0.021 – 0.040 < 2.00 0.078 ≥ 5.01 – 10.00 0.201 – 0.393 3 100 x 100 39.37 x 39.37

D ≥ 1.01 – 1.50 0.041 – 0.059 < 4.00 0.157 Not allowed 1 100 x 100 39.37 x 39.37

E ≥ 1.51 0.060 ≥ 4.00 0.157 Not allowed Not allowed 100 x 100 39.37 x 39.37

Combination of type B, C Total maximum number of defects 10 100 x 100 39.37 x 39.37

A y isual defe t less tha . . ” dia eter shall e a epted pro ided they are ot losely grouped together luster) which make them easily detectable.

Notes referring to the table.

Clusters: A maximum of three (3) visual defects with size 0.25 – 1.5 mm (0.010 – . ” are allo ed i a ” dia eter ir le. Clusters should ot e loser tha ” to ea h other.

Optiglasspc

QUALITY DEPARTMENT

PROPERTY

DIMENSION

Gauge Tolerance

REQUIREMENT TEST

Nominal Gauge Range Min. Limit Max Limit TM 2000

A aila le . ” - . ”

-10% +10%

Width Tolerance 48"

- ” + ” TM 4000

Length 96"

APPEARANCE

Substrate

- ” + ” TM 5000

Warpage

Length divided by 100 TM 1800

Squareness

.500" (Max.) TM 2400

Ripples/Distortion Compared Against Visual TM 2700

Standard

QUALITY DEPARTMENT

ABRASION RESISTANCE PROPERTIES

Reference: ASTM D1044-08 Standard Test method for Resistance of Transparent Plastics to Surface Abrasion

*Data source – ASTM D1044-08, Table 1 Note - The above information is to be used for general comparative purposes only. Individual laboratory testing may

produce different values due to variations in test procedures, equipment and environmental conditions at the time of the

testing. Refer to ASTM D1044, Section 10, Precision and Bias, for additional information.

CHEMICAL RESISTANCE PROPERTIES

Acetone Good

Windex® Good

Methylene Chloride Good

Toluene Good

Sulfuric Acid Good

Nitric Acid Good

Isopropanol Good

Kerosene Good

Polycarbonate vs. Glass

Cycles ∆ Haze value

Glass* 1000 0.69

Polycarbonate HMR

1000 3.31

500 1.91

100 0.81

Polycarbonate uncoated* 100 42.12

8991 Flammability Cover Letter.pdf8991 Test Method.pdf