d&c b240 supply of bolts, nuts, screws and washers · ed 1/rev 0 . first issue ... the...

ROADS AND MARITIME SERVICES (RMS)

RMS SPECIFICATION D&C B240

SUPPLY OF BOLTS, NUTS, SCREWS AND WASHERS

NOTICE

This document is a Roads and Maritime Services D&C Specification. It has been developed for use with Design & Construct roadworks and bridgeworks contracts let by Roads and Maritime Services. It is not suitable for any other purpose and must not be used for any other purpose or in any other context.

Copyright in this document belongs to Roads and Maritime Services.

REVISION REGISTER

Ed/Rev Number

Clause Number Description of Revision Authorised

By Date

Ed 1/Rev 0 First issue GM, IC W Stalder

20.07.11

Ed 2/Rev 0 Updated to accord with changes to base (non-D&C) Specification B240

GM, IC 01.08.12

Ed 2/Rev 1 Updated to accord with changes to base (non-D&C) Specification B240

MCQ 27.10.17

Edition 2 / Revision 1 ROADS AND MARITIME SERVICES October 2017

SPECIFICATION D&C B240


Copyright – Roads and Maritime Services IC-DC-B240

VERSION FOR: DATE:

Edition 2 / Revision 1 ROADS AND MARITIME SERVICES October 2017

Supply of Bolts, Nuts, Screws and Washers D&C B240

CONTENTS

CLAUSE PAGE

FOREWORD ............................................................................................................................................... II RMS Copyright and Use of this Document ................................................................................... ii Base Specification ......................................................................................................................... ii

1 GENERAL ........................................................................................................................................ 1 1.1 Scope .............................................................................................................................. 1 1.2 Structure of the Specification ......................................................................................... 1 1.3 Definitions and Abbreviations ....................................................................................... 2

2 QUALITY MANAGEMENT SYSTEM .................................................................................................. 3

3 MATERIALS AND MANUFACTURE .................................................................................................. 3 3.1 Structural Bolts, Nuts and Washers ............................................................................... 3 3.2 Other Fasteners ............................................................................................................... 3 3.3 Stainless Steel Fasteners ................................................................................................ 6 3.4 Locking Devices ............................................................................................................. 6 3.5 Protective Treatment for Fasteners ................................................................................ 7

4 PRODUCT CONFORMITY ................................................................................................................. 7 4.1 Nonconforming Test Results .......................................................................................... 8

5 TRACEABILITY ............................................................................................................................... 8

6 DOCUMENTATION .......................................................................................................................... 8

7 PACKAGING AND STORAGE ............................................................................................................ 8

ANNEXURE B240/A – PROJECT SPECIFIC REQUIREMENTS ...................................................................... 9 A1 Details of Work .............................................................................................................. 9 A2 Additional Testing Requirements ................................................................................... 9 A3 Tests to Be Waived ........................................................................................................ 9

ANNEXURE B240/B – (NOT USED) ........................................................................................................... 9

ANNEXURE B240/C – SCHEDULES OF HOLD POINTS AND IDENTIFIED RECORDS .................................. 10 C1 Schedule of Hold Points ............................................................................................... 10 C2 Schedule of Identified Records .................................................................................... 10

ANNEXURE B240/D – (NOT USED) ........................................................................................................ 10

ANNEXURE B240/E – PRELOADING SUITABILITY TEST ......................................................................... 11 E1 Test Aim ....................................................................................................................... 11 E2 Test Arrangement and Measuring Device .................................................................... 11 E3 Test Assemblies ............................................................................................................ 11 E4 Test Procedure .............................................................................................................. 12 E5 Test Report ................................................................................................................... 12 E6 Acceptance Criterion .................................................................................................... 12

ANNEXURES B240/F TO B240/K – (NOT USED)..................................................................................... 12

Ed 2 / Rev 1 i

D&C B240 Supply of Bolts, Nuts, Screws and Washers

ANNEXURE B240/L – TEST METHODS AND SAMPLING FREQUENCY ..................................................... 13 L1 Mechanical Tests .......................................................................................................... 13 L2 Chemical Tests ............................................................................................................. 15 L3 Test Certificate ............................................................................................................. 15

ANNEXURE B240/M – REFERENCED DOCUMENTS................................................................................. 16

LAST PAGE OF THIS DOCUMENT IS .......................................................................................................... 18

FOREWORD

RMS COPYRIGHT AND USE OF THIS DOCUMENT

Copyright in this document belongs to Roads and Maritime Services.

When this document forms part of a deed

This document should be read with all the documents forming the Project Deed.

When this document does not form part of a deed

This copy is not a controlled document. Observe the Notice that appears on the first page of the copy controlled by RMS. A full copy of the latest version of the document is available on the RMS Internet website: http://www.rms.nsw.gov.au/business-industry/partners-suppliers/specifications/index.html

BASE SPECIFICATION

This document is based on Specification RMS B240 Edition 5 Revision 1.

ii Ed 2 / Rev 1

http://www.rms.nsw.gov.au/business-industry/partners-suppliers/specifications/index.html

(RMS COPYRIGHT AND USE OF THIS DOCUMENT - Refer to the Foreword after the Table of Contents)

RMS QA SPECIFICATION D&C B240


1 GENERAL

1.1 SCOPE

This Specification sets out the requirements for the supply of bolts, nuts, screws, washers, stud and threaded rods for steelwork. It also includes requirements for the supply of stainless steel fasteners.

The Specification requires suppliers to provide testing and traceability to give assurance of fastener quality.

This Specification details the default protective treatment of the fasteners. Additional paint treatment may be specified elsewhere on the Design Documentation drawings or other deed documents.

1.2 STRUCTURE OF THE SPECIFICATION

This Specification includes a series of annexures that detail additional requirements.

1.2.1 Details of Work

Project specific requirements are shown in Annexure B240/A.

1.2.2 (Not Used)

1.2.3 Schedules of HOLD POINTS and Identified Records

The schedules in Annexure B240/C list the HOLD POINTS that must be observed. Refer to Specification RMS D&C Q6 for the definition of HOLD POINTS.

The records listed in Annexure B240/C are Identified Records for the purposes of RMS D&C Q6 Annexure Q/E.

1.2.4 (Not Used)

1.2.5 Frequency of Testing

The Inspection and Test Plan must nominate the proposed testing frequency to verify conformity of the item and it must not be less than that specified in Annexure B240/L. Where a minimum frequency is not specified, nominate an appropriate frequency.

You may propose to the Project Verifier a reduction in the frequency of testing. Any such proposal must be supported by a statistical analysis demonstrating consistent process capability and product characteristics. The Project Verifier may vary or reinstate the original minimum frequency of testing at any time.

Ed 2 / Rev 1 1



1.2.6 Referenced Documents

Standards, specifications and test methods are referred to in abbreviated form (e.g. AS 1234). For convenience, the full titles are given in Annexure B240/M.

1.3 DEFINITIONS AND ABBREVIATIONS

1.3.1 Definitions

The terms “you” and “your” mean “the Contractor” and “the Contractor’s” respectively.

The following definitions apply to this Specification:

Fasteners: Items used to secure or join together individual items of steelwork; e.g. screws, bolts, nuts, studs, threaded bars, washers and holding down bolts.

High strength bolts, screws, studs, threaded bars and nuts: Heat treated carbon steel bolts, screws, studs and threaded rods of property class 8.8 or higher, and nuts of property class 8 or higher.

Lot: Either: (a) Items of the same designation produced from the same heat using the same manufacturing

process; or (b) Items of the same designation produced from the same process cycle without modifications to

the settings of the continuous production process.

Lot identification number: Unique number assigned by the manufacturer, allowing full traceability from the finished product item back through all previous manufacturing operations to a given heat number or cast number of the raw material of manufacture.

Low strength bolts, screws, studs, threaded bars and nuts: Carbon steel bolts, screws, studs and threaded bars of property class 4.6 or 4.8, and nuts with property class 5, not subjected to heat treatment during manufacturing.

Manufacturer: Entity manufacturing fasteners from raw feedstock.

Mild steel washers: Washers not subjected to heat treatment during manufacturing.

Product grade: The precision of manufacture of the fastener, based on the applicable dimensional tolerances. Grade A is the most precise and grade C is the least precise.

Property class (PC): Numbers stamped on the fastener indicating its strength. Bolts, screws and studs have a two-digit number, the first digit being 100th of the nominal tensile strength in MPa and the second digit being 10 times the ratio of the lower yield strength (or stress at 0.2% permanent set) to the nominal tensile strength, with a decimal point between. Nuts have a single digit number representing 100th of the proof load stress in MPa, except for thin nuts which have a zero in front of the single digit.

Structural bolt assembly: An assembly of bolts, nuts and washers conforming to AS/NZS 1252 commonly used in structural engineering applications.

Studs: Short rods or bars threaded at both ends or for the whole length, for use with nuts.

2 Ed 2 / Rev 1



Supplier: An Australian business entity responsible for ensuring conformity of the supplied fasteners to this Specification, including local representatives of overseas manufacturers, wholesalers, importers and contractors.

Trace number: Alphanumeric code assigned to a consignment of fasteners by the supplier that identifies the original manufacturer and the Lot identification number.

1.3.2 Abbreviations

The following abbreviations apply to this Specification:

AISI American Iron and Steel Institute

JAS-ANZ Joint Accreditation System for Australia and New Zealand

NATA National Association of Testing Authorities, Australia

PC Property class

HV Vickers Hardness

HRC Rockwell Hardness measured on the C scale

TB Bearing-type tensioned bolt conforming to AS 5100.6

TF Friction-type tensioned bolt conforming to AS 5100.6

2 QUALITY MANAGEMENT SYSTEM Fasteners conforming to this Specification must be manufactured and supplied by organisations which have in place third party accredited quality management systems, complying with AS/NZS ISO 9001, which are recognised under the Joint Accreditation System of Australia and New Zealand (JAS-NZS) or an affiliated international accreditation organisation.

The Supplier must provide documentation to this effect with each consignment of fasteners supplied in conformity to this Specification.

3 MATERIALS AND MANUFACTURE

3.1 STRUCTURAL BOLTS, NUTS AND WASHERS

High strength structural bolts, PC 8.8 (sizes M16 to M36), high strength nuts, PC 8 (sizes M16 to M36) and hardened steel washers must conform to AS/NZS 1252.

The material properties, dimensional tolerances and protective treatment of high strength structural bolts, nuts and washers must conform to AS/NZS 1252.

Supply bolts, nuts and washers as assemblies. The nuts must be able to run up and down the bolts by hand.

3.2 OTHER FASTENERS

This clause sets out the requirements for fasteners other than those specified in Clause 3.1.

Ed 2 / Rev 1 3



Unless shown otherwise on the Design Documentation drawings, all fastener dimensions are metric.

3.2.1 Steel Bolts and Nuts

This clause is applicable to steel bolts and nuts with ISO metric coarse pitch thread.

The material properties, dimensional tolerances and protective treatment of bolts and nuts must conform to Table B240.1.

Table B240.1 - Manufacturing and Material Requirements for ISO Metric Steel Bolts and Nuts

Common Name Product Grade / Manufacturing Standard

Property Class / Material Standard Protective Treatment

High

Stre

ngth

ISO metric hexagon head bolts PC 8.8 A or B AS 1110.1 8.8 AS 4291.1 Zinc plated or uncoated

ISO metric hexagon head bolts PC 10.9 A or B AS 1110.1 10.9 AS 4291.1 Zinc plated or uncoated

ISO metric hexagon nuts PC 8 A or B AS 1112.1 8 AS/NZS 4291.2 Zinc plated or uncoated

ISO metric hexagon nuts PC 10 A or B AS 1112.1 10 AS/NZS 4291.2 Zinc plated or uncoated

ISO metric cup head bolts PC 8.8 (1) - AS 1390 (for

dimensions only) 4.6 AS/NZS 4291.1 Zinc plated or uncoated or hot-dip galvanized

Low

Stre

ngth

ISO metric hexagon head bolts PC 4.6 C AS 1111.1 4.6 AS 4291.1 Hot-dip galvanized or

uncoated

ISO metric hexagon nuts PC 5 C AS 1112.3 05 AS/NZS 4291.2 Zinc plated or uncoated or hot-dip galvanized

ISO metric cup head bolts PC 4.6 - AS/NZS 1390 4.6 AS/NZS 4291.1 Zinc plated or uncoated or

hot-dip galvanized

ISO metric thin hexagon nuts PC 05 (2) A or B AS 1112.4 05 AS/NZS 4291.2 Zinc plated or uncoated

Notes: (1) AS 1390 covers cup head bolts to PC 4.6 only; high strength cup head bolts need to be specially specified. (2) Low strength thin nuts PC 05 are typically used as lock nuts with high or low tensile fasteners.

For ISO metric bolts or other threaded components of a particular property class, use only steel nuts of the corresponding property class shown in Table B240.2 below.

Table B240.2 - Property Classes of ISO Metric Nuts

Property class of bolt, U-bolt, screw, etc. 4.6 4.8 5.6 8.8 10.9

Property class of nut 5 5 5 8 10

3.2.2 Steel Screws

Dimensional tolerances and material properties for steel screws must conform to Table B240.3. All steel screws must have ISO metric coarse pitch thread.

Self-drilling steel screws for fixing to steel must conform to AS 3566, with Class 4 protective coating.

4 Ed 2 / Rev 1



Table B240.3 - Manufacturing and Material Requirements for ISO Metric Screws

Common Name Product Grade / Manufacturing Standard

Property Class/ Material Standard

Typical Protective Treatment

High

Stre

ngth

ISO metric hexagon head screws PC 8.8 A or B AS 1110.2 8.8 AS 4291.1 Zinc plated or uncoated

ISO metric hexagon head screws PC 10.9 (1) A or B AS 1110.2 10.9 AS 4291.1 Zinc plated or uncoated

ISO metric hexagon socket head cap screws PC 10.9 A AS 1420 or

DIN 912 10.9 AS 4291.1 Zinc plated or uncoated

ISO metric hexagon socket head cap screws PC 12.9 A AS 1420 or

DIN 912 12.9 AS 4291.1 Zinc plated or uncoated

ISO metric countersunk socket head screws PC 10.9 - ISO 10642 or

BS 4168 10.9 AS 4291.1 (or ISO 898-1) Zinc plated or uncoated

ISO metric countersunk socket head screws PC 12.9 (1) - ISO 10642 or

BS 4168 12.9 AS 4291.1 (or ISO 898-1) Uncoated

Low

Stre

ngth ISO metric hexagon head

screws PC 4.6 C AS 1111.2 4.6 AS 4291.1 Zinc plated or uncoated or hot-dip galvanized

Notes: (1) Indicates an item that may not be readily available in the Australian market.

3.2.3 Washers

Hardened steel washers for use with PC 8.8 fasteners or higher must conform to AS/NZS 1252 or ASTM F436M.

Steel washers for use with PC 4.6, PC 4.8 or PC 5.6 bolts must conform to AS 1237.

Unless shown otherwise on the Design Documentation drawings, the hardness of washers associated with steel bolts or threaded rods must be as shown in Table B240.4.

Table B240.4 - Hardness of Washers

Property class of bolts, threaded rods, etc. PC 4.6, PC 4.8 PC 8.8, PC 10.9

Minimum washer hardness 200 HV 345 – 445 HV (35 – 45 HRC) for black

270 – 445 HV (26 – 445 HRC) for hot-dip galvanized

Unless shown otherwise on the Design Documentation drawings, all washers must be flat, round and normal size. Oversize or square washers must be as shown on the Design Documentation drawings.

3.2.4 Steel Studs and Associated Nuts

ISO metric high strength steel studs must be PC 8.8 to AS 2528 or ASTM A193M. Associated nuts must be PC 8 to AS 2528 or ASTM A194M.

ISO metric low strength steel studs must be PC 4.6 to AS 2528. Associated nuts must be PC 5 to AS 2528.

High strength steel studs in imperial dimensions must be Grade B7 to AS 2528 or ASTM A193. Associated nuts must be Grade 2H to AS 2528 or ASTM A194.

Ed 2 / Rev 1 5



Low strength steel studs in imperial dimensions must be Grade B8 to AS 2528. Associated nuts must be Grade 8 to AS 2528.

3.2.5 Steel Threaded Rods, Holding Down Bolts and Non-Standard Fasteners

The pitch and dimensional tolerances of threaded rods and associated nuts must conform to AS 1275 or ISO 965 with material property class to AS 4291.1 and AS/NZS 4291.2 or ISO 898-1 and ISO 898-2 as specified on the Design Documentation drawings.

U-bolts, L-bolts and non-standard fasteners must be supplied with dimensions, material grade and protective treatment conforming to the Design Documentation drawings. Any departures from the specified dimensions, materials and protective treatment must be approved by the RMS Representative before manufacture.

Notwithstanding Clause 8.1 of Specification RMS B201, bolts to be welded must be PC 4.6 to AS 4291.1, and not be manufactured from free-cutting steels as defined in AS 1443. Welding must otherwise conform to Specification RMS D&C B201.

3.2.6 Fasteners in Imperial Units

Unified hexagon bolts, screws and nuts must conform to AS/NZS 2465 or an equivalent international standard.

3.3 STAINLESS STEEL FASTENERS

Unless shown otherwise on the Design Documentation drawings, stainless steel fasteners must be austenitic AISI 316L to ASTM A240 and ASTM A660 (or equivalent) steel with maximum 0.03 % carbon and minimum 2% molybdenum.

High strength stainless steel fasteners must have a minimum ultimate tensile strength of 800 MPa.

The manufacture of stainless steel fasteners must conform to Table B240.5.

Table B240.5 - Manufacturing Requirements for Stainless Steel Fasteners

Fastener Manufacturing / Dimension Standard

ISO metric hexagon head bolts ISO 4014 (or DIN 931)

ISO metric hexagon head screws ISO 4017

ISO metric hexagon socket head cap screws ISO 4762 (or AS 1420)

ISO metric hexagon nuts ISO 4032

Washers ISO 7089 or ISO 7090 for chamfered washers (or DIN 125A (withdrawn))

ISO metric threaded rods ISO 965

3.4 LOCKING DEVICES

Use only locking devices approved by the Project Verifier.

6 Ed 2 / Rev 1



3.5 PROTECTIVE TREATMENT FOR FASTENERS

Unless shown otherwise on the Design Documentation drawings, supply fasteners with protective treatment conforming to Table B240.6.

Table B240.6 - Protective Treatment of Fasteners

Fastener Type Protective Treatment

High strength structural bolts and associated nuts and washers

Hot-dip galvanized in accordance with AS 1214

Hexagon head bolts and screws PC 4.6, and associated washers and nuts

Threaded rods PC 4.6 or PC 8.8, and associated nuts and washers

Holding down bolts and associated nuts and washers

Cup head bolts

Hexagon head bolts and screws PC 8.8 or PC 10.9, Product grades A and B, and associated washers and nuts

Electroplated with zinc in accordance with AS 1789 or mechanically plated in accordance with ASTM B695-04

Hexagon socket head cap screws PC 10.9 or PC 12.9 Black with residual coating of light oil

Countersunk socket head screws PC 10.9 or PC 12.9

Stainless steel fasteners Plain without protective treatment

Self drilling screws Class 4 to AS 3566.2

Locking devices As approved by the Project Verifier

Where specified in Annexure B240/A1, use thermal diffusion galvanizing instead of hot-dip galvanizing or zinc plating. Ensure that the specified thermal diffusion galvanizing layer thickness can be achieved for the bolt assembly product grades and the thread dimension tolerances.

Carry out trial assembly of sample fastener components with the specified coatings, to verify the components will fit properly.

4 PRODUCT CONFORMITY Product conformity of ISO metric coarse threaded fasteners must be established by testing to conform to Annexure B240/L.

Testing of imperial fasteners must conform to the appropriate material and manufacturing standard(s), e.g. AS/NZS 2465. The frequency of testing of imperial fasteners must conform to Annexure B240/L for the equivalent ISO metric fastener grade.

Test only finished fasteners. Testing of fasteners prior to heat treatment or cold or hot working is not acceptable.

Where the Project Verifier identifies higher risks associated with product applications, carry out additional testing as specified in Annexure B240/A2.

Where items of small quantities (i.e. less than 50) are used in a low risk situation, the requirements for testing may be waived by the Project Verifier, as specified in Annexure B240/A3.

Ed 2 / Rev 1 7



4.1 NONCONFORMING TEST RESULTS

Where any test specimen fails to meet the acceptance criteria, the Lot must be discarded and replaced.

5 TRACEABILITY Markings for bolts, screws, nuts and studs must be clearly visible, uniform and in accordance with the applicable standard, e.g. AS 4291.1, AS/NZS 4291.2.

Each supplied item must be traceable. Control and record the Lot identification number for each item at every stage of the production, to enable identification of the source of each item and each production process used for its manufacture.

6 DOCUMENTATION Provide the documents specified in Clause 2, and the following documents, prior to delivery to Site of each consignment of fasteners:

(i) Statement of conformity of the fasteners to the applicable manufacturing and material standard(s) specified in this Specification;

(ii) Details of supplier’s business entity and address, the Lot identification number for traceability of each fastener, and the fastener description/designation, in accordance with Clause 5; and

(iii) Test certificates for the fasteners in accordance with Annexure B240/L3.

HOLD POINT

Process Held: Delivery of each consignment of fasteners to Site.

Submission Details: Documents specified in Clauses 2 and 6, at least 7 working days before delivery.

Release of Hold Point: The Nominated Authority will consider the submitted documents prior to authorising the release of the Hold Point.

7 PACKAGING AND STORAGE Supply fasteners with the same Lot identification number in the same box or in boxes with identical labels for large quantities.

Store fasteners in a waterproof enclosure, clear of the ground and protected from damage.

8 Ed 2 / Rev 1



ANNEXURE B240/A – PROJECT SPECIFIC REQUIREMENTS

Project specific requirements to be completed by the Designer.

Refer to Clause 1.2.1.

A1 DETAILS OF WORK

Item Requirements

Fastener type, size, length (where applicable) and quantity (insert additional rows as required)

Applicable standards

Type of surface finish

Delivery location

Other (specify)

A2 ADDITIONAL TESTING REQUIREMENTS

Refer to Clause 4.

Description of Additional Test Number of Samples

Examples of additional tests required:

• Impact Test to Clause 8.7 of AS 4291.1

• Preloading Suitability Test (1) to Annexure B240/E. This test is recommended wherever high tensile bolts are to be tensioned during installation, i.e. TF and TB installation categories.

A3 TESTS TO BE WAIVED

Refer to Clause 4.

List here any tests to be waived.

ANNEXURE B240/B – (NOT USED)

Ed 2 / Rev 1 9



ANNEXURE B240/C – SCHEDULES OF HOLD POINTS AND IDENTIFIED RECORDS

Refer to Clause 1.2.3.

C1 SCHEDULE OF HOLD POINTS

Clause Description

6 Submission of documents specified in Clauses 2 and 6.

C2 SCHEDULE OF IDENTIFIED RECORDS

The records listed below are Identified Records for the purposes of RMS D&C Q6 Annexure Q/E.

Clause Description of Identified Record

2 Third party accreditation of suppliers and manufacturers.

4 Product conformity testing records.

5 Lot identification records.

6 Fastener documentation.

ANNEXURE B240/D – (NOT USED)

10 Ed 2 / Rev 1



ANNEXURE B240/E – PRELOADING SUITABILITY TEST (Note: This test must be carried out by suppliers on high strength structural bolt assemblies. The test may be suitable for other grades of fasteners that tensioned during installation, as specified in Annexure B240/A2.)

E1 TEST AIM

The test verifies the suitability of bolt or screw or threaded rod assemblies for tensioned bolted connections, i.e. TB or TF categories conforming to AS 5100.6.

E2 TEST ARRANGEMENT AND MEASURING DEVICE

The test arrangement must be as illustrated in Figure B240/E.1, except that one or more shims with hardness not less than the washer hardness may be used to suit the measuring device. Additional hardened washers may be used as shims.

Restrain the bolt head from turning during the tightening of the nut.

The measuring device must allow continuous measurements at one measurement per second of bolt tension up to yield. The measuring system must be capable of measuring the bolt force with an uncertainty of not more than ± 5% of the actual value. A washer type load cell, a sensor or an equivalent may be used for the measuring device. Hydraulic measuring devices must not be used for this test.

Figure B240/E.1 – Test Arrangement (from EN 14399-2)

E3 TEST ASSEMBLIES

The test fastener assembly must comprise the bolt and associated nuts and washers. All test assembly components must only be used once.

The test must be carried out on the test assembly in the delivery condition without lubrication of the individual fastener items.

Ed 2 / Rev 1 11



E4 TEST PROCEDURE

Tension the bolt by tightening the nut with an electric or manual torque wrench. The rate of tightening must produce a tensioning rate of 8 kN to 12 kN per second for bolts up to 24 mm nominal diameter and 18 kN to 22 kN for bolts of larger diameters.

Continue tightening the nut until one of the following occurs:

(i) The bolt fractures;

(ii) The bolt tension does not increase; or

(iii) A bolt tension of 1.05 times the bolt proof load is achieved.

If fracture does not occur, check for permanent deformation of the threads by running the nut up and down the bolt by hand.

E5 TEST REPORT

Report the maximum tension in the bolt, any permanent deformation of the threads and the type, location and description of the fracture and the fracture surfaces (where applicable).

E6 ACCEPTANCE CRITERION

The fastener assembly is conforming if:

(i) a bolt tension at least equal to the bolt proof load is achieved; and

(ii) the nut runs freely up the bolt at the end of the test.

ANNEXURES B240/F TO B240/K – (NOT USED)

12 Ed 2 / Rev 1



ANNEXURE B240/L – TEST METHODS AND SAMPLING FREQUENCY Refer to Clauses 1.2.5 and 4.

L1 MECHANICAL TESTS

All mechanical testing must be performed by laboratories with third party accreditation by a signatory to the International Laboratories Accreditation Cooperation (ILAC) scheme, e.g. NATA. The testing must conform to Table B240/L.1.

The minimum number of test specimens from each Lot for each of the specified tests must be in accordance with Tables B240/L.1 and B240/L.2.

Tensile tests must be carried out instead of wedge tensile test for bolts with nominal diameters larger than 39 mm.

Carry out hardness tests on high strength structural steel bolts, screws, studs, threaded rods and nuts, using the Vickers scale only. Conversion of hardness test results from other hardness scales to the Vickers scale is not acceptable.

The proof load test is a destructive test. Discard all proof load test samples on completion.

Table B240/L.1 – Mechanical Testing Requirements

Fastener Tensile Strength Proof Load Other Tests

High strength structural bolts

Wedge test to Clause 2.4 of AS/NZS 1252 (Test Plan B)

Clause 2.4 of AS/NZS 1252 (Test Plan B)

Preloading Suitability Test to Annex. B240/E (Test Plan B)

Vickers test to Clause 2.3 of AS/NZS 1252 (Test Plan B)

Structural nuts N/A Clause 3.4 of AS/NZS 1252 (Test Plan B)

Vickers test to Clause 3.3 of AS/NZS 1252 (Test Plan B)

Structural washers N/A N/A Vickers or Rockwell test to Clause 4.3 of AS/NZS 1252 (Test Plan C)

High strength bolts Wedge test to Clause 8.6 of AS 4291.1 (Test Plan A)

Clause 8.5 of AS 4291.1 (Test Plan A)

Vickers test to Clause 8.4 of AS 4291.1 (Test Plan C)

High strength nuts N/A Clause 8.1 of AS/NZS 4291.2 (Test Plan A)

Vickers test as in accordance with Clause 8.2 of AS/NZS 4291.2 (Test Plan C)

High strength screws other than socket head cap screws

Wedge test to Clause 8.6 of AS 4291.1 (Test Plan A)



High strength socket head cap screws




High strength studs or threaded rods

Wedge test to Clause 2.3.6.3 of AS 2528 (Test Plan A)

Clause 2.3.6.2 of AS 2528 (Test Plan A)

Vickers test to Clause 2.3.6.6 of AS 2528 (Test Plan C)

Ed 2 / Rev 1 13



Fastener Tensile Strength Proof Load Other Tests

Hardened washers N/A N/A Vickers hardness test to AS 1817 or Rockwell hardness test to AS 1815 (Test Plan B)

Low strength bolts Clause 8.2 (or wedge test to Clause 8.6) of AS 4291.1 (Test Plan B)

Clause 8.5 of AS 4291.1 (Test Plan B)

Low strength screws Clause 8.2 (or wedge test to Clause 8.6) of AS 4291.1 (Test Plan B)


Low strength nuts N/A Clause 8.1 of AS/NZS 4291.2 (Test Plan B)

Low strength studs or threaded rods


Clause 2.3.6.2 of AS 2528 (Test Plan B)

Mild steel washers N/A N/A Hardness test to AS 1237 (Test Plan B)

Stainless steel bolts Clause 7 of ISO 3506-1 (Test Plan B)

Clause 7 of ISO 3506-1 (Test Plan B)

Stainless steel screws Clause 7 of ISO 3506-1 (Test Plan B)


Stainless steel nuts N/A Clause 7 of ISO 3506-2 (Test Plan B)

Stainless steel studs or threaded rods



Stainless steel washers N/A N/A

Vickers hardness test to AS 1817 or Rockwell hardness test to AS 1815 (Test Plan B)

Self drilling screws Clause 1.11 of AS 3566.1 N/A

14 Ed 2 / Rev 1



Table B240/L.2 - Minimum Sample Size for Test Plans

Lot Size Minimum Sample Size (see Note 3)

Test Plan A Test Plan B Test Plan C

≤ 50 2 1 1

> 50 and ≤ 200 3 1 1

> 200 and ≤ 1,000 5 2 1

> 1,000 and ≤ 5,000 8 3 2

> 5,000 and ≤ 10,000 12 3 2

> 10,000 16 4 2 Notes: 1. Table B240/L.2 supersedes Table A1 of AS/NZS 1252. 2. Bolts or screws of the same type and diameter of different lengths produced from the same heat under

the same conditions are a single Lot. 3. Where a Lot of high strength bolts or screws includes different bolt lengths, share the required number

of tests in Table B240/L.2 evenly, rounded up to the nearest integer, between the different lengths. Example: A purchase order for bolts to AS/NZS 1252 consists of 100×M20-100 and 100×M20-150

produced at the same time and under the same conditions (including the same heat treatment), requires 2, 1 and 1 samples for Test Plans A, B and C, respectively, for each bolt length.

L2 CHEMICAL TESTS

Carry out one chemical composition test per Lot.

L3 TEST CERTIFICATE

The test certificate must include the following:

(i) Test certificate number and test date;

(ii) Test description and applicable standard;

(iii) Laboratory address and contact details;

(iv) Laboratory accreditation details;

(v) Identification of test specimen and Lot;

(vi) Chemical composition of Lot;

(vii) Description of test specimen and stage of manufacture at the time of testing;

(viii) Test result and acceptance criteria;

(ix) Description of type and location of failure and the fracture surfaces; and

(x) Name of tester and dated signature.

Ed 2 / Rev 1 15



ANNEXURE B240/M – REFERENCED DOCUMENTS Refer to Clause 1.2.6.

RMS Specifications

RMS D&C Q6 Quality Management System (Type 6)

RMS D&C B201 Steelwork for Bridges

Australian Standards

AS 1110 ISO metric hexagon bolts and screws - Product grades A and B

AS 1110.1 Bolts

AS 1110.2 Screws

AS 1111 ISO metric hexagon bolts and screws - Product grade C

AS 1111.1 Bolts

AS 1111.2 Screws

AS 1112 ISO metric hexagon nuts

AS 1112.1 Style 1 - Product grades A and B

AS 1112.2 Style 2 - Product grades A and B

AS 1112.3 Product grade C

AS 1112.4 Chamfered thin nuts - Product grades A and B

AS 1214 Hot-dip galvanized coatings on threaded fasteners (ISO metric coarse thread series)

AS 1237 Plain washers for metric bolts, screws and nuts for general purposes

AS 1237.1 General plan

AS 1237.2 Tolerances

AS/NZS 1252 High strength steel bolts with associated nuts and washers for structural engineering

AS 1275 Metric screw threads for fasteners

AS/NZS 1390 Cup head bolts with ISO metric coarse threads

AS 1420 ISO metric hexagon socket head cap screws

AS 1443 Carbon and carbon-manganese steel - Cold finished bars

AS 1789 Electroplated zinc (electro-galvanized) coatings on ferrous articles (batch process)

AS 1815 Metallic materials - Rockwell hardness test

AS 1817 Metallic materials - Vickers hardness test

AS/NZS 2465 Unified hexagon bolts, screws and nuts (UNC and UNF threads)

AS 2528 Bolts, studbolts and nuts for flanges and other high and low temperature applications

16 Ed 2 / Rev 1



AS 3566 Self-drilling screws for building and construction industry

AS 3566.1 General requirements and mechanical properties

AS 3566.2 Corrosion resistance requirements

AS 4291 Mechanical properties of fasteners made of carbon steel and alloy steel

AS 4291.1 Bolts, screws and studs

AS/NZS 4291.2 Nuts with specified proof load - Coarse thread

AS 5100.6 Bridge design - Steel and composite construction

AS/NZS ISO 9001 Quality management systems - Requirements

ISO Standards

ISO 898 Mechanical properties of fasteners made of carbon steel and alloy steel

ISO 898-1 Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread

ISO 898-2 Nuts with specified proof load values - Coarse thread

ISO 965 ISO general-purpose metric screw threads

ISO 4014 Hexagon head bolts - Product grades A and B

ISO 4017 Hexagon head screws - Product grades A and B

ISO 4032 Hexagon nuts, Style 1 - Product grades A and B

ISO 4762 Hexagon socket head cap screws

ISO 7089 Plain washers - Normal series - Product grade A

ISO 7090 Plain washers, chamfered - Normal series - Product grade A

ISO 10642 Hexagon socket countersunk head screws

ASTM Standards

ASTM A193 Alloy-steel and stainless steel bolting for high temperature or high pressure service and other special purpose applications

ASTM A194 Carbon and alloy steel nuts for bolts for high pressure or high temperature service, or both

ASTM A240 Chromium and chromium-nickel stainless steel plate, sheet, and strip for pressure vessels and for general applications

ASTM A660 Annealed or cold-worked austenitic stainless steel sheet, strip, and flat bar

ASTM B695-04 Coatings of zinc mechanically deposited on iron and steel

ASTM F436M Hardened steel washers

British Standards

BS 4168 Hexagon socket screws and wrench keys

Ed 2 / Rev 1 17

http://www.saiglobal.com/online/Script/Details.asp?DocN=ISOA00005_0904



German Standards

DIN 125A Product grade A washers

DIN 912 Socket head cap screws

DIN 931 Hexagon head bolts with shank

18 Ed 2 / Rev 1