design project - college of engineering - purdue university · web viewcurrently there are “home...
TRANSCRIPT
![Page 1: Design Project - College of Engineering - Purdue University · Web viewCurrently there are “Home automation systems” available that can do some of the things that the Suite is](https://reader037.vdocument.in/reader037/viewer/2022100900/5ac4f2c27f8b9a333d8d8db4/html5/thumbnails/1.jpg)
ECE 477 Digital Systems Senior Design Project Rev 8/11
Homework 3: Design Constraint Analysis and Component Selection Rationale
Team Code Name: ___Home Enhancement Suite___________________ Group No. __10__Team Member Completing This Homework: ____Nathan Irvin________________________E-mail Address of Team Member: ___nirvin_____ @ purdue.edu
Evaluation:
SCORE DESCRIPTION
10 Excellent – among the best papers submitted for this assignment. Very few corrections needed for version submitted in Final Report.
9Very good – all requirements aptly met. Minor additions/corrections needed for version submitted in Final Report.
8Good – all requirements considered and addressed. Several noteworthy additions/corrections needed for version submitted in Final Report.
7Average – all requirements basically met, but some revisions in content should be made for the version submitted in the Final Report.
6Marginal – all requirements met at a nominal level. Significant revisions in content should be made for the version submitted in the Final Report.
* Below the passing threshold – major revisions required to meet report requirements at a nominal level. Revise and resubmit.
* Resubmissions are due within one week of the date of return, and will be awarded a score of “6” provided all report requirements have been met at a nominal level.
Comments:7/10 Report does not explain many things well, see comments below. Parts list severely lacking; only $30+ of the project cost has been planned?
George Toh
![Page 2: Design Project - College of Engineering - Purdue University · Web viewCurrently there are “Home automation systems” available that can do some of the things that the Suite is](https://reader037.vdocument.in/reader037/viewer/2022100900/5ac4f2c27f8b9a333d8d8db4/html5/thumbnails/2.jpg)
ECE 477 Digital Systems Senior Design Project Rev 8/11
Introduction
The Home Enhancement Suite is a package that will control various aspects of a room in
an autonomous fashion when a user is recognized through RFID. Currently, there are home
automation kits available, but generally these do not incorporate different settings for different
people. The Home Enhancement Suite will allow a user to automate the lighting as well as set up
an HDMI product, such as a television, to their favorite channel and volume.
The Suite will also feature software that runs on a home PC that will allow the user to
quickly and easily set-up the user profiles as well as change the settings as desired. The software
program in conjunction with the room unit will work seamlessly together to provide users with a
unique experience of automation.
The design itself will be centered around a microcontroller that controls each of the
systems including X10 communication, CEC-HDMI communication, and working an electronic
door lock as well as RFID interpretation. The micro will also communicate with a PC, through
ethernet, running a new software program that allows users to adjust and save their settings.
Updated PSSCs
1. An ability to detect a user based on RFID and determine which user has priority, displaying
the user's identity on an LCD.
2. An ability to adjust the light intensity to match a user’s settings through X10 protocol.
3. An ability to adjust a television set or other HDMI device using CEC-HDMI protocol, to a
user's preferred settings. (ON/OFF, Channel, Volume)
4. An ability to unlock a door when an appropriate RFID is present.
5. An ability to select/set preferred settings through a computer program and the ability to save
the "light settings" with the press of a button.
For an updated block diagram, please see Appendix B.
1.0 Design Constraint AnalysisThe main tasks that the Home Enhancement Suite must accomplish are the ability to
communicate through X10 and CEC-HDMI, control of an electronic door lock, interpretation of
an RFID tag, and communication with a PC running a program that is also hosting the users’
-2-
![Page 3: Design Project - College of Engineering - Purdue University · Web viewCurrently there are “Home automation systems” available that can do some of the things that the Suite is](https://reader037.vdocument.in/reader037/viewer/2022100900/5ac4f2c27f8b9a333d8d8db4/html5/thumbnails/3.jpg)
ECE 477 Digital Systems Senior Design Project Rev 8/11
settings. The micro will be in charge of all communication with peripherals and the control of the
“fail-safe” electric strike. The program will be in charge of interpreting the users’ settings and
communicating properly with the micro.
Cost is not a major concern as other home automation kits available are very expensive.
This system should be a much more affordable option and allow the user to choose what features
they want to purchase and how many rooms they would like to expand to. The packaging should
be fairly simple and unobtrusive when placed in a room. As a prototype, cosmetics are not a
priority, but the ability for it to be visually appealing in a final design should have some merit.
The design is not going to be mobile and will therefore be running off of a home’s
standard AC. For this reason, efficiency is not a primary concern, but the idea of home
automation lends to a more efficient environment, so the design should be conscientious of this
fact as well.
1.01 Computation RequirementsThe Home Enhancement Suite, or simply referred to as “the Suite” for the remainder of
this document, will have to do various computational tasks. To begin with, it must recognize an
RFID obtained via a reader and check that the ID is an acceptable user. It must then unlock the
door if necessary followed immediately by executing the proper X10 protocol to adjust the light
intensity to the user’s preferred settings. The Suite must also execute the proper CEC-HDMI
protocol to set up the television to the user’s preferred settings. In addition, the Suite will also be
in charge of interpreting the intensity setting, should the user like to immediately save the current
setup to their profile. All settings will be stored on a local PC and the Suite will communicate
with the PC via ethernet. In addition, the Suite must output the current “active” user on an LCD
display.
1.02 Interface RequirementsThe Suite will need to interface with many modules through various connections/ports.
The RFID readers will be connected through USB and therefore the Suite will require a total of 3
USB ports (2 for the optional exterior door and one located centrally in the room). It will connect
to a PL513 via an RJ-11 telephone jack and connect to the host PC through ethernet. Finally, the
Suite will connect to an electric strike through a standard 2-pin header. The Suite will feature a
-3-
![Page 4: Design Project - College of Engineering - Purdue University · Web viewCurrently there are “Home automation systems” available that can do some of the things that the Suite is](https://reader037.vdocument.in/reader037/viewer/2022100900/5ac4f2c27f8b9a333d8d8db4/html5/thumbnails/4.jpg)
ECE 477 Digital Systems Senior Design Project Rev 8/11
microcontroller that supports ethernet and at least one USB connection. The additional On-chip
Peripheral requirements will be explained in section 2.03 of this analysis. Optical isolation will
be utilized in the electric strike drive circuit as protection against any malfunction of the strike
itself.
1.03 On-Chip Peripheral RequirementsThe Suite will require a minimum of 1 Ethernet, 1 USB, 1 ADC, 3 General Purpose I/O
pins, and 2 SPI. The general purpose I/Os will be used to control the electric strike and
communicate via HDMI using the CEC protocol as well as accept the “user save” function that
allows the user to press a button and save the current light setting. One of the SPI will be used to
execute the X10 protocol and the other will communicate with the LCD display module. The
ADC will be used to interpret the ambient light reading. Finally, the USB will connect to a USB
hub control expanding it to the required 3 USB ports for the Suite.
1.04 Off-Chip Peripheral RequirementsThe Suite will require a few additional Off-Chip peripherals. The main one is a PLIX IC
that will be interfaced with through one of the SPI. This chip will then connect via an RJ-11
telephone jack to the PL513 which is connected to the AC power line for communication with
the X10 protocol. This portion of the system will control the intensity of the light. An analog-to-
digital converter will be used if not available on-chip to convert the analog signal registered by
an ambient light sensor. A USB hub controller IC will be used to create 2 additional USB ports
which will receive the RFID reader data.
1.05 Power ConstraintsThe Suite will be A.C. powered only and there will not be any major concerns with
current draw. We will implement an on-board power supply, such that we have access to
VUNREG and can utilize it to charge a capacitor that will be discharged to provide the necessary
current burden to operate the electric strike for unlocking the door. The PLIX IC requires 5
VDC, while the USB controllers and micros selected require 3.3 VDC and are more efficient.
As cost is not of primary concern, the Suite will feature both regulators, operating off of
VUNREG to supply the necessary components.
-4-
![Page 5: Design Project - College of Engineering - Purdue University · Web viewCurrently there are “Home automation systems” available that can do some of the things that the Suite is](https://reader037.vdocument.in/reader037/viewer/2022100900/5ac4f2c27f8b9a333d8d8db4/html5/thumbnails/5.jpg)
ECE 477 Digital Systems Senior Design Project Rev 8/11
1.06 Packaging ConstraintsThere are no major packaging-related constraints for this system. The finished product
should be unobtrusive and fit on a normal desk top or on top of a typical entertainment stand.
The system is not going to be portable and therefore does not have any strict dimension
tolerances or structural demands.
1.07 Cost ConstraintsCurrently there are “Home automation systems” available that can do some of the things
that the Suite is capable of doing, but there are no products that are identical in nature. Many of
the other systems control aspects of the home that the Suite does not address as they are not
prudent and are simply a cost that can be saved. There is a product developed by HomeSeer [1]
that requires the purchase of software for roughly $200 and then the purchase of various
controllers to add to the system. The overall cost would end up being roughly $1000 to
implement the software, RFID receivers and all necessary components for X10 communication.
The Home Enhancement Suite will handle those features and more without the purchase of
additional items, but will be limited in overall execution and abilities and therefore it is important
that the cost be kept well under the current market. The Suite, including all of the necessary
components should be available for roughly $600.
2.0 Component Selection RationaleThe Suite’s main component, the microcontroller, does not have a lot of very specific
design constraints. Speed is not of much importance, so the previously mentioned peripherals
were the driving force for selection. Two options were considered as candidates which included
the PIC32MX664F064L(PIC32)[2] from Microchip and the AT32UC3A0512(AT32)[3] from
Atmel. Both were selected based on the peripherals including the necessary ethernet, SPI, and
one on-board USB. Both have sufficient flash with plenty of overhead to accommodate any
additional features added to the Suite. The approximate cost for the PIC32 is $7.10 and the
approximate cost for the AT32 is not available, but samples are and the cost is expected to be
similar. Currently, the PIC32 has been selected for the prototype.
The next major component choice is the PLIX chip, or Power Line Interface for X-10.
This IC is currently only being produced by one company, Micromint USA [4], and therefore it
-5-
![Page 6: Design Project - College of Engineering - Purdue University · Web viewCurrently there are “Home automation systems” available that can do some of the things that the Suite is](https://reader037.vdocument.in/reader037/viewer/2022100900/5ac4f2c27f8b9a333d8d8db4/html5/thumbnails/6.jpg)
ECE 477 Digital Systems Senior Design Project Rev 8/11
has not been compared to any other candidates. If the IC is not available, it can be created from
passive components and some very involved programming. The PLIX chip is designed to
eliminate the issues and concerns with using a microcontroller to communicate using the X-10
protocol.
An additional component that required some consideration is the ambient light sensor.
Vishay[5] offers various surface mount options including the TEMT6000 and TEMT6200. For
our expected illuminance, both offer similar characteristics and can be obtained for less than
$1.50 through various suppliers.
The last major component being addressed in this report is a USB controller IC. There are
many options available so a low-cost option is being pursued. Because the microcontroller itself
has one USB included, the Suite requires two additional ports. There are USB controllers that
are capable of adding these and interfacing with the micro via SPI, but there are also hub chips
available. One option would be to interface the on-chip USB with a hub controller to give 4
downstream ports, which is more than enough. Atmel offers the AT43301[6], which is a low-
cost USB Hub Controller and does exactly as described above. Another available option is
offered by Texas Instruments in the TUSB2046B[7] package. This chip also does exactly as
described above in a different footprint. Because they are comparable in functionality, and price
is not of utmost concern, a final decision will be made based on available real-estate on the
PCB. For a current proposal, the TUSB2046B will be selected.
3.0 SummaryThe Home Enhancement Suite will bring a user one step-closer to automated, seamless
living throughout the home. The user will be able to easily enter and walk throughout the home
as it configures to their pre-configured settings. The Suite will interface with already existing
technology through various ports and the microcontroller selected to control the system is the
PIC32MX664F064L. A PLIX interface chip will be utilized in conjunction with the X-10
protocol to control the lights. All other circuit components are readily available through various
manufacturers. For the prototype, there are no strict price or packaging constraints as it is
assumed the final product will be well under the current home automation systems available.
-6-
![Page 7: Design Project - College of Engineering - Purdue University · Web viewCurrently there are “Home automation systems” available that can do some of the things that the Suite is](https://reader037.vdocument.in/reader037/viewer/2022100900/5ac4f2c27f8b9a333d8d8db4/html5/thumbnails/7.jpg)
ECE 477 Digital Systems Senior Design Project Rev 8/11
List of References
[1] HomeSeer [Online]. Available: http://www.homeseer.com [Accessed: Jan. 30, 2012]
[2] PIC32MX664F064L [Online]. Available: http://www.microchip.com/wwwproducts/Devices.aspx?dDocName=en552074 [Accessed: Jan. 28, 2012]
[3] Atmel Corporation - Atmel AVR 8- and 32- bit Microcontrollers - 32-bit AVR UC3 [Online]. Available: http://www.atmel.com/dyn/products/product_card.asp?category_id=163&family_id=607&subfamily_id=2138&part_id=4117 [Accessed: Jan. 28, 2012]
[4] Power Line Interface for X-10 (PLIX) [Online]. Available: http://www.micromint.com/index.php/Micromint-Chips/plix.html [Accessed: Jan 26, 2012]
[5] Vishay Broadens Portfolio of Ambient Light Sensors with Surface-Mount 0805 Devices [Online]. Available: http://www.vishay.com/company/press/releases/2006/060707sensors/ [Accessed: Jan 31, 2012]
[6] Atmel Low-cost USB Hub Controller [Online]. Available: http://www.atmel.com/dyn/resources/prod_documents/doc1137.pdf [Accessed: Jan 27, 2012]
[7] USB Hub Controller ICs from Texas Instruments [Online]. Available: http://focus.ti.com/paramsearch/docs/parametricsearch.tsp?family=analog&familyId=366&uiTemplateId=NODE_STRY_PGE_T [Accessed: Jan 31, 2012]
-7-
![Page 8: Design Project - College of Engineering - Purdue University · Web viewCurrently there are “Home automation systems” available that can do some of the things that the Suite is](https://reader037.vdocument.in/reader037/viewer/2022100900/5ac4f2c27f8b9a333d8d8db4/html5/thumbnails/8.jpg)
ECE 477 Digital Systems Senior Design ProjectFall2008
Appendix A: Parts List Spreadsheet
Vendor Manufacturer
Part No. Description Unit Cost Qty Total Cost
Microchip PIC PIC32MX664F064L Microcontroller 7.02 1
Micromint Micromint Serial PLIX PLIX 24.00 1Sparkfun Vishay TEMT6000 Ambient Light Sensor 1.50 1Texas Instruments TI TUSB2046B USB Hub Controller 1.20 1
TOTAL 33.72(Please remember that not all parts are included at this time)
-8-
![Page 9: Design Project - College of Engineering - Purdue University · Web viewCurrently there are “Home automation systems” available that can do some of the things that the Suite is](https://reader037.vdocument.in/reader037/viewer/2022100900/5ac4f2c27f8b9a333d8d8db4/html5/thumbnails/9.jpg)
ECE 477 Digital Systems Senior Design ProjectFall2008
Appendix B: Updated Block Diagram
-9-