determination of an ideal motorcycle lane …psasir.upm.edu.my/47509/1/fk 2012 40r.pdfuniversiti...
TRANSCRIPT
UNIVERSITI PUTRA MALAYSIA
MOHAMMAD RASOOL AHMAD RAJABI
FK 2012 40
DETERMINATION OF IDEAL WIDTH FOR EXCLUSIVE MOTORCYCLE LANE ALONG THE STRAIGHT SECTION OF FEDERAL HIGHWAY,
SELANGOR, MALAYSIA
DETERMINATION OF IDEAL WIDTH FOR EXCLUSIVE MOTORCYCLE LANE ALONG THE STRAIGHT SECTION OF FEDERAL HIGHWAY,
SELANGOR, MALAYSIA
BY
MOHAMMAD RASOOL AHMAD RAJABI
Thesis Submitted to the School of Graduate Studies, Universiti Putra Malaysia, in Fulfilment of the Requirements for the Degree of Master of
Science
May 2012
© COPYRIG
HT UPM
ii
Abstract of thesis presented to the Senate of Universiti Putra Malaysia in fulfilment of the requirement for the degree of Master of Science
DETERMINATION OF IDEAL WIDTH FOR EXCLUSIVE MOTORCYCLE LANE ALONG THE STRAIGHT SECTION OF FEDERAL HIGHWAY,
SELANGOR, MALAYSIA
By
MOHAMMAD RASOOL AHMAD RAJABI
May 2012
Supervisor: HUSSAIN B HAMID, PhD
Faculty: Engineering
In the design of roadway, factors such as lane width, lateral clearance,
vertical and horizontal alignment affects the capacity and Level-Of-Service
(LOS). Ideal lane width is the upper limit range of width in which optimum
capacity is achieved. There are numerous studies and literature available on
the design of bicycle facilities. However, there are limited literature and
studies about design of motorcycle facilities.
The main issue pertaining to the provision of motorcycle facility is the width of
its lane. If the width of the motorcycle lane is too wide, it may incur
unnecessary construction costs and also leads to speeding problems. On the
other hand, if the width of the lane is too narrow, the riding convenience and
safety of motorcyclists may be affected particularly when overtaking is not
possible. It is necessary to understand the basic sciences of motorcycles
© COPYRIG
HT UPM
iii
traffic so that a more scientific and professional judgment can be made with
regard to the design and operation of motorcycle facilities.
As such, this research aims to determine the effective factors affected by the
motorcycle lane width, to establish relationship between these factors and
finally determine the ideal width of motorcycle lane.
Study sites which met the research criteria were selected along the existing
exclusive motorcycle lane along the Federal Highway, Selangor, Malaysia.
To observe motorcyclists riding and passing another motorcyclist within the
motorcycle lane, the segments under study are at least 100 m long and
covered lane widths ranging from 1.8 m to 3.3 m.
Motorcycle flow was recorded using a digital video recorder and motorcycle
count is obtained by transcribing the pre-recordings in the laboratory.
Individual motorcycle spot speeds were measured using a laser speed
detector. To observe motorcyclists riding comfort, transcription was done on
the pre-recordings video in the laboratory where classification of comfortable
or not comfortable used riding interruptions as a surrogate in the field.
Aggregated motorcycle flow, speed and comfort data collected at 16 different
motorcycle lane widths were plotted. Quadratic regression analysis was
employed for the motorcycle flow-width relationship, Analysis of Variance
(ANOVA) test for the motorcycle speed-width relationship, and logistic
regression analysis for comfortable width.
© COPYRIG
HT UPM
iv
Results revealed that maximum motorcycle flow (mc/hr/m) occurs at 2.7 m
wide lane, comfort is observed at 2.7 m lane or wider, and motorcycle speeds
stabilized along 2.5 m lane or wider.
Hence, 2.7 m is an ideal lane width for motorcycle lanes which encompassed
the optimum of motorcyclist riding comfort, speed and flow. The findings of
this study not only contribute new knowledge to the field of transportation
engineering but would also be useful input in the design guidelines of
motorcycle lanes for highly motorcycled countries.
© COPYRIG
HT UPM
v
Abstrak tesis yang dikemukakan kepada Senat Universiti Putra Malaysia sebagai memenuhi keperluan untuk ijazah Master Sains
PENENTUAN LEBAR YANG UNGGUL UNTUK LORONG MOTOSIKAL EKSKLUSIF SEPANJANG SEKSYEN LEBUH RAYA PERSEKUTUON,
SELANGOR, MALAYSIA
Oleh
MOHAMMAD RASOOL AHMAD RAJABI
Mei 2012
Pengerusi: Hussain B Hamid, PhD
Fakulti: Kejuruteraan
Dalam reka bentuk jalan, faktor-faktor seperti lebar lorong, kelegaan sisi,
penjajaran mendatar dan tegak mempengaruhi muatan dan tahap
perkhidmatan (LOS). Lebar lorong unggul ialah julat batas kelebaran di mana
muatan optima dicapai. Terdapat banyak kajian dan penulisan yang boleh
didapati tentang reka bentuk kemudahan-kemudahan basikal.
Bagaimanapun, penulisan dan kajian-kajian tentang reka bentuk
kemudahan-kemudahan motosikal adalah terhad.
Isu utama berkaitan dengan penyediaan kemudahan motosikal ialah
kelebaran lorongnya. Jika kelebaran lorong motosikal adalah terlalu luas, ia
boleh menyebabkan peningkatan kos pembinaan yang tidak perlu dan juga
masalah-masalah operasi. Sebaliknya, jika kelebaran lorong terlalu sempit,
keselesaan menunggang dan keselamatan penunggang motosikal boleh
terjejas terutamanya jika penunggang tidak dapat memotong motosikal yang
© COPYRIG
HT UPM
vi
lain. Adalah perlu untuk memahami sains asas kenderaan motosikal supaya
keputusan yang lebih profesional dan saintifik dapat dibuat berhubung
dengan reka bentuk dan operasi kemudahan-kemudahan motosikal.
Oleh itu, penyelidikan ini bertujuan untuk menentukan faktor-faktor berkesan
yang mempengaruhi kelebaran lorong motosikal, mewujudkan hubungan
antara faktor-faktor ini dan akhirnya menentukan kelebaran lorong motosikal
unggul.
Tapak kajian yang memenuhi kriteria penyelidikan dipilih sepanjang lorong
motosikal eksklusif di sepanjang Lebuhraya Persekutuan, Selangor,
Malaysia. Untuk pemerhatian penunggang motosikal dan pemotongan
penunggang motosikal yang lain di dalam ruang lorong motosikal, segmen-
segmen di bawah kajian adalah sekurang-kurangnya 100 m panjang dan
meliputi lebar lorong dari 1.8 m ke 3.3 m.
Aliran motosikal direkodkan menggunakan perakam video digital dan
bilangan motosikal diperolehi dengan mentranskripsi pra-rakaman di
makmal. Kelajuan setempat motosikal masing-masing diukur menggunakan
pengesan kelajuan laser. Untuk pemerhatian keselesaan menunggang
motosikal, transkripsi dilakukan dari pra-rakaman video di makmal itu di
mana pengelasan selesa atau tidak selesa bagi penunggang motosikal
menggunakan gangguan menunggang motosikal sebagai pemerhatian
pengganti di tapak kajian.
© COPYRIG
HT UPM
vii
Data aggregasi aliran motosikal, kelajuan dan keselesaan yang dikutip di 16
kelebaran lorong motosikal yang berbeza telah diplotkan. Analisis regresi
kuadratik digunakan untuk hubungan kelebaran-aliran motosikal, analisis
regresi fungsi bersyarat eksponen (ECFR) digunakan untuk hubungan
kelebaran-kelajuan motosikal, dan analisis regresi logistik untuk kelebaran
selesa.
Keputusan mendedahkan bahawa aliran motosikal maksimum
(motosikal/jam/m) berlaku pada lorong selebar 2.7 m, keselesaan
diperhatikan pada lorong selebar 2.7 m atau lebih, dan kelajuan motosikal
stabil di sepanjang lorong selebar 2.5 lorong m atau lebih.
Oleh itu, nilai 2.7 m ialah lebar lorong unggul untuk lorong motosikal yang
merangkumi keselesaan menunggang motosikal, kelajuan dan aliran
motosikal yang optima. Penemuan-penemuan kajian ini bukan sahaja
menyumbang ilmu baru bagi bidang kejuruteraan pengangkutan tetapi juga
dapat menjadi maklumat berguna sebagai garis panduan reka bentuk lorong
motosikal untuk negara-negara yang mempunyai bilangan motosikal yang
tinggi.
© COPYRIG
HT UPM
viii
ACKNOWLEDGEMENTS
In the Name of Allah, Most Gracious, Most Merciful, all praise and thanks are
due to Allah, and peace and blessings be upon His Messenger. I would like
to express the most sincere appreciation to those who made this work
possible: supervisory members, Friends and Family.
Firstly I would like to thank my supervisor Dr. Hussain Hamid for the many
useful advice and discussions, for his constant encouragement, guidance,
support and patience all the way through my study work. Equally the
appreciation extends to the supervisory committee members Dr. Sulistyo
Arintono for providing me the opportunity to complete my studies under their
valuable guidance.
I would also like to acknowledge the Civil Engineering Department of
Universiti Putra Malaysia, JKR and Roadcare for providing the numerous
facilities and support for this research work.
Thanks and acknowledgements are meaningless if not extended to my wife
and my parents who always gave relentless encouragement and support
which made my education possible.
Last but not least, my very special thanks to all my friends who were directly
and indirectly involved in this research and cooperated with this study.
© COPYRIG
HT UPM
ix
I certify that an Examination Committee has met on 23 May 2012 to conduct the final examination of Mohammad Rasool Ahmad Rajabi on his Master of Science thesis entitled "DETERMINATION OF IDEAL WIDTH FOR EXCLUSIVE MOTORCYCLE LANE ALONG THE STRAIGHT SECTION OF FEDERAL HIGHWAY, SELANGOR, MALAYSIA" in accordance with Unversiti Pertanian Malaysia (HIGHER Degree) Act 1980 and Universiti Pertanian Malaysia (High Degree) Regulation 1981. The committee recommends that the candidate be awarded the relevant degree. Members of the Examination Committee are as follows:
Thamer Ahmad Mohammad, PhD Professor Faculty of Engineering Universiti Putra Malaysia (Chairman)
Ratnasamy a/I Muniandy, PhD Professor Faculty of Engineering Universiti Putra Malaysia (Internal Examiner)
Law Teik Hua, PhD Assoc. Professor Faculty of Engineering Universiti Putra Malaysia (Internal Examiner)
Wan Hashim Wan Ibrahim, PhD Professor Faculty of Engineering University Malaysia Sarawak (External Examiner)
__________________________________ SEOW HENG FONG, PhD Professor and Deputy Dean
School of Graduate Studies Universiti Putra Malaysia Date:
© COPYRIG
HT UPM
x
This thesis was submitted to the Senate of Universiti Putra Malaysia and has been accepted as fulfilment on the requirement for the degree of Master of Science. The members of the supervisory committee were as follows:
Hussain Hamid, PhD Senior Lecturer Faculty of Engineering Universiti Putra Malaysia (Chairman)
Sulistyo Arintono, PhD Senior Lecturer Faculty of Engineering Universiti Putra Malaysia (Member)
__________________________________ BUJANG BIN KIM HUAT, PhD Professor and Dean
School of Graduate Studies Universiti Putra Malaysia Date:
© COPYRIG
HT UPM
xi
DECLARATION
I declare that the thesis is my original work as per program given to me, except for quotations and citations, which have been duly acknowledged. I also declare that it has not been previously, and is not concurrently, submitted for any other degree at Universiti Putra Malaysia or other institutions.
__________________________________ MOHAMMAD RASOOL AHMAD RAJABI
Date: 23 May 2012
© COPYRIG
HT UPM
xii
TABLE OF CONTENTS
Page ABSTRACT ii ACKNOWLEDGEMENTS viii APPROVAL ix
DECLARATION xi LIST OF TABLES xiv
LIST OF FIGURES xv
LIST OF ABBREVIATIONS xvii
CHAPTER
1 INTRODUCTION 1
1.1 Motorcycle Transportation in Malaysia 1 1.2 Safety Engineering Program for Motorcyclists 1 1.3 Problem Statement 3 1.4 Objectives of the Study 4 1.5 Significance of the Study 5 1.6 Scope and Limitation of Study 5 1.7 Thesis Layout 6
2 LITERATURE REVIEW 8
2.1 Introduction 8 2.2 Fundamental Principles of Traffic Flow 8
2.2.1 Effects of Density on Vehicle Flow 9 2.2.2 Effects of Flow Rate of Vehicles against Lane Width 10 2.2.3 Definitions of Speed of Velocity 10 2.2.4 Speed-Flow-Density Relationship 12
2.3 Factors Affecting Lane Width 14 2.4 Relationship between Various Factors and Lane Width 17
2.4.1 Relationship between Safety and Lane Width 17 2.4.2 Relationship between Flow Rate and Lane Width 19 2.4.3 Relationship between Speed and Lane Width 20
2.5 Factors Affected by Lane Width 23 2.5.1 Types of Motorcycle Lane Facility 24 2.5.2 Motorcycle Operating Width 27 2.5.3 Motorcycle Comfortable Safe Width 29
2.6 Motorcycle Traffic Science 30 2.7 Motorcycle Lane Studies in Asian Countries 33 2.8 Bicycle Facilities 35
2.8.1 Bicycle Statics Space 35 2.8.2 Typical Bicycle Operating Space 36 2.8.3 Bicycle Lane Width Characteristics 37
2.9 Chapter Summary 38
© COPYRIG
HT UPM
xiii
3 RESEARCH METHODOLOGY 40
3.1 Introduction 40 3.2 Review of Study to Identify related Factors to Lane Width 43 3.3 Field Study and Data Collection 44
3.3.1 Study Site and Selection Criteria 44 3.3.2 Standard Field Parameters and Measuring Equipment 47 3.3.3 Methodology of the Study 51 3.3.4 Impact of Safety Cones on Motorcyclists Behaviour 55 3.3.5 Definition of Comfortable Overtaking 56
3.4 Motorcycle Speed-Width, Flow-Width and Comfortable-Width Models 59 3.4.1 Modelling Motorcycle Comfortable-Width 59 3.4.2 Modelling Motorcycle Flow-Width 63 3.4.3 Modelling Motorcycle Speed-Width 64
3.5 Chapter Summary 67
4 RESULTS AND DISCUSSION 69
4.1 Related Factors to Ideal Lane Width 69 4.2 The Comfortable Lane Width 70
4.2.1. Comfort-Width Model 72 4.3. Motorcycle Flow-Width Relationship 77
4.3.1. Normality of Data 80 4.3.2. Model Fitting of Motorcycle Flow-Width Regression Model 80
4.4. Motorcycle Speed-Width Relationship 84 4.4.1. Scatter Plot of Speed-Width of Relationship 85 4.4.2. Statistic Tests 86 4.4.3. Normality of the Data 87 4.4.4. One-way ANOVA 88
4.5. Determination of an Ideal Lane Width for Exclusive Motorcycle Lane 94
5 CONCLUSIONS AND RECOMMENDATION 97
5.1 Introduction 97 5.1. Related Factors to Ideal Lane Width 97 5.2. Motorcycle Comfortable-Width Relationship 98 5.3. Motorcycle Flow-Width relationship 98 5.4. Motorcycle Speed-Width relationship 99 5.5. Determination of an Ideal Lane Width for Exclusive Motorcycle
Lane 99 5.6. Applications 99 5.7. Further Study Recommendation 100
REFERENCES 102
APPENDIX A 106
APPENDIX C 109
APPENDIX D 140
APPENDIX E 150
BIODATA OF STUDENT 157
© COPYRIG
HT UPM