detroit assurance lane departure warning camera 54-29110.1 hold the digital level used in step 5 up...

Detroit Assurance Lane Departure Warning Camera Installation

FLA COE FLB COE FLD Conventional Business Class FLC 112 Conventional

Century Class Conventional Argosy COE Cargo Columbia

122SD and Coronado Business Class M2

> Cascadia 108SD/114SD

Description of Revisions: This bulletin replaces the version dated September 2015. There are now two possible locations for the camera base, depending on the parameter setting for the VRDU camera.

General Information Use the instructions in this bulletin to replace the Detroit Assurance VRDU camera.

Parts Refer to Table 1 for camera cover and base part numbers.

Camera Mounting Assembly Parts Description Part Number

Cover - Camera, Global Radar 1 8-67 468-000

Cover - Camera Base, Global Radar A 1 8-67911 -000

Table 1, Camera Mounting Assembly Parts

54-291 Freightliner

Service Bulletin

NOTE: A camera mounting training aid has been designed by "DTNA Custom Built Training Aids" and is available through the Aftermarket Resource Center (ARC) website. See Fig. 1. The training aid can be used as an alternative to the mounting procedure described in this bulletin. Connect the vehicle to Diagnosticlink to verify which parameter is programmed on the vehicle. The order form for the tool can be accessed by clicking the "Training Aids" link located on the lower right-hand side of ARC's home page, then clicking "Detroit Camera Mounting Tool Order Form" on the right-hand side of the page. It is still necessary to order the camera mounting assembly parts described in Table 1 before the camera can be mounted using this tool.

Check the parameter setting for the VRDU camera in Diagnosticlink before using the training aid. If the training aid is being used on a vehicle programmed with parameter 000 447 36 51, position the training aid on the passenger-side windshield, so the left edge is mounted 4 inches (100 mm) from the center rubber seal and the top edge sits against the windshield upper rubber seal.

Freightliner Service Bulletin, September 2016

54-291 Detroit Assurance Lane Departure Warning Camera

Installation Freightliner Service Bulletin



A The training aid is used to position the camera base on the windshield.

1. Camera Base 2. Windshield 3. Camera Mounting Training Aid

Fig. 1, Camera Mounting Training Aid

Installing the Detroit VRDU camera 1. Park the vehicle and apply the parking brakes.



2. Run the engine until the air system is fully charged, then shut down the engine and chock the tires.

NOTE: Components installed on the windshield may interfere with the mounting template. It may be helpful to remove them before installing the VRDU camera.

IMPORTANT: Completely clean the area where the camera will be mounted. If the windshield is not clean and free of grease and dust, the camera may not properly adhere to the windshield surface.

3. Clean the windshield mounting surface with IPA wipe (50/50 mix of isopropyl alcohol and water) or equivalent cleaner. Use a clean towel, and make sure the windshield surface is completely clean and free of grease and dust.

4. Create the template included with this bulletin.

IMPORTANT: When printing the template, make sure that the "Actual Size" radio button is selected under the "Size" tab, the "Auto portrait/landscape" radio button is selected under the "Orientation" heading, and that the "1-sided" radio button is selected on the properties screen. See Fig. 2 and Fig. 3.

4.1 Print the template provided on the last page of this bulletin.

Page2 Freightliner Service Bulletin, September 2016



...,, Prmter. [\\c:GfJ1 p4l.Z\WRPRTA

co,;« p l;. P.iigc,; te- Print

(Ufrttltp~" ~' ------It, P-11gcs .g

~ MortOpt1(h"t1


j Surnm1riJt: Corr11nt11lt j

85 11" 1llnchH

__ ._,..._.._,.,,._ 54.N1

P119e1SiDf19&~~· --~~~-~ ~ U£11 (RI ... ..,~. II a ... , .. I ~ ~ ~ .R' -.-C

''"°"''°"" ---------------( Fit 2 @ Acti.11)ri2t :-:---_

Sh.-,k0fff5il:irdp.g~ 3 O <ttooM p.pu ,ovru: by PDF P.9C WM

EJ P,111t on both SldH of PIP8

:::06;:,uli.ndiu~ ----4 (" Ponr,rt

______ -,

r===.·;-----:~-=:~ ·-~--:

· )



'>tttll'l<J> Help

• .. , ,.~Lir,w. [r..,. IPnCb!tr ]oo.itc,tima '

Copies Orierfati on

'> I 6J r-' MM

_,, rG3 ~·-~Coln-OOUN

r Pwtlad.1>9l'm r AotUllO" -2-sidedpnntJng MLitJpage pnrong (N-Up)

~mi;:idd:ior+J Paoetoeo~ -

00 ;ti [!;::: < Uw-- ,JI ~ !"] .. , ..... LlJ r ....,::::::------_ 1 Qr :l-med1~WJ1J

Mo,& Page Layout Opions ...

54-291 Freightliner

Service Bulletin

!I!!!!

-

[] ~:s;..,.np.

~ ' - .. - u .. ..---...

.......,..

I

D o D LEXM+\RK OQ~ P&gt l af8 04/15/2015 1120335

1. 1-sided Radio Button 04/24/2015 1120336

1 . Properties Button Fig. 3, Document Properties Screen

2. Size Tab 3. "Actual Size" Radio Button 4. "Auto Portrait/Landscape" Radio Button

Fig. 2, Print Screen

4.2 Using a ruler, verify the length of the printed ruler graphic on the template. If the length of the ruler graphic does not measure accurately, the template did not scale properly. Repeat this step until the markings on the printed ruler match those of the ruler in hand.

4.3 Secure the template to a piece of thick cardboard with glue or tape. See Fig. 4.

Freightliner Service Bulletin, September 2016 Page3

54-291 Freightliner Service Bulletin

04/13/2015




Fig. 4, Template Taped to Cardboard



1546164

4.4 Cut along the border, through the template and the cardboard, using a razor knife and straight edge. See Fig. 5. Verify the dimensions shown on the template.

Page4 Freightliner Service Bulletin. September 2016



04/13/2015




Fig. 5, Template Cut with a Razor Knife

54-291 Freightliner

Service Bulletin

1546165

5. Using a digital level, take a level reading of the surface where the vehicle is parked. See Fig. 6.

01/17/2013 1545981

Fig. 6, Measuring the Level on the Surface where the Vehicle is Parked

6. Determine the correct mounting location for the camera based on the vehicle parameter setting for the VRDU camera:

Freightliner Service Bulletin. September 2016 Page5

54-291 Detroit Assurance Lane Departure Warning Camera

Installation Freightliner Service Bulletin





• 000 447 27 51: Vehicles built before 12/7/2015. See Fig. 7 for the parameter description in Diagnosticlink. Note that vehicles built before this date may have had the parameter changed to accommodate other components. Verify the correct parameter number by connecting the vehicle to Diagnosticlink and selecting Detroit Assurance. The left side of the camera base is 4.7 inches (120 +/- 5 mm) from the right side of the windshield center rubber seal.

ca~Odpl,ce-rnem

C.tmffa Pllc:h ifflglfl

tamrf'ii!I rnH ~

~y,iw•n91e

09/20/2016

A000-14 727S 1-00 I Oe:ti1utt CalJ"N.a Conf,glflllOn DTNA (fromp,1trM 2.51 m 1.llO

(from Plretl 0.17 m --0.50 (ftomPMffiO -11.6 -20.D

(ftom pa,,mi) OJI ·10.0

(l!omoa,en~ 0.0 ·IO.D

Fig. 7, Diagnosticlink Description for Parameter 000 447 27 51

410 ~hrightoftht!arna_

o.so lne hon:orttal Cl@l6Ce-

5.0 fh4' tf19le bftwttn lhi! -

10.D IM' angle bylmK:h the -

10.0 The iJJ19'4: by 'M'll'Ch me _

f546610

• 000 447 36 51: Vehicles built after 12/7/2015. See Fig. 8 for the parameter description in Diagnosticlink. The left side of camera base is 8.6 inches (220 +/- 5 mm) from the right side of the windshield center rubber seal.

.::J tll vn(IU)I T ~·-~ 9 d Cll"Mr.t P1.flffl!te-

umn• heigh.t camna drsplac~1mt

(~i!IP,illttlflligle

(arnetl ,o11 lni;I~

c.o\Mt'fayiawanoi~

09/20/2016

ta:0«73611-001 Dt:1a"h~Cor.flgintfon0lNA DTNlli.oVan (lrcmp,ar~t) 2.11 m 1.llO

(tromp.a,e-itJ 027 m -0.IO

(fromp,e""'I) -IJ.6 -2QJJ

(lrom~ieno 0.0 -10.0

(tmmoarenU 0.0 -100

Fig. 8, Diagnosticlink Description for Parameter 000 447 36 51

'10

OIO

5.0 10.0

100

To. he4't oi ~ ume-r. 1hr t,ori..:oota d 1"Sp!'ace ...

The q:~ DC'M~tn lMt -~ 11"19;,e ~\lli'l•(h tM -lht ano ia t,y "'"'4"1,cl'I w _

f546609

7. If the vehicle is programmed with parameter 000 447 27 51, position the template on the passenger-side windshield, so the left edge is against the center rubber seal and the top edge sits against the windshield upper rubber seal.

If the vehicle is programmed with parameter 000 447 36 51, position the template on the passenger-side windshield, so the left edge is mounted 4 inches (100 mm) from the center rubber seal and the top edge sits against the windshield upper rubber seal.

8. Tape the template to the windshield.

IMPORTANT: Do not re-use the camera base. If the windshield is being replaced, or other service is performed that requires the removal of the camera base, a new camera base must be installed.

9. Remove the protective liner from the back of the camera base.

10. Install the camera base on the windshield.

10.1 Hold the digital level used in step 5 up to the tabs on the camera base. While holding the digital level on the base, hold the bottom of the camera base away from the windshield glass and align the top of the camera base with the template. While maintaining zero level, lower the bottom of the camera base until it contacts the windshield.

10.2 Verify proper alignment of the camera base.

Page6

Use the dimensions shown in Fig. 9 for vehicles with parameter 000 447 27 51.

Use the dimensions shown in Fig. 10 for vehicles with parameter 000 447 36 51.

Freightliner Service Bulletin, September 2016

Detroit Assurance Lane Departure Warning Camera Installation 54-291





Freightliner Service Bulletin

Hold the digital up to the tabs on the camera base. See Fig. 11 . The level reading should be the same as the reading taken of the surface where the vehicle is parked (±0.4 degrees, with a maximum spec of ±1.5 degrees). If the base is aligned correctly, continue with step 9. If the base is not aligned correctly, remove it immediately before it cures and repeat steps 10.1 and 10.2.

09/21/2016 f546611

A. Horizontal orientation is measured 4.7 inches (120 mm ± 5) from the right edge of the windshield centerline to the edge of the camera base.

B. Vertical orientation is measured 1 .3 inches (33 mm ± 5) from the top of the camera base to the bottom edge of the windshield rubber seal.

C. This line is parallel to the upper seal with a maximum roll angle of less than 0.4°.

Fig. 9, Camera Mounting on Vehicles with Parameter 000 447 27 51

Freightliner Service Bulletin. September 2016

09/20/2016 f546612

A. Horizontal orientation is measured 8.6 inches (220 mm ± 5) from the right edge of the windshield centerline to the edge of the camera base.

B. Vertical orientation is measured 1 .3 inches (33 mm ± 5) from the top of the camera base to the bottom edge of the windshield rubber seal.

C. This line is parallel to the upper seal with a maximum roll angle of less than 0.4°.

Fig. 10, Camera Mounting on Vehicles with Parameter 000 447 36 51

54-291 Freightliner Service Bulletin



1. Template 2. Camera Base 3. Digital Level


Fig. 11, Aligning the Base with a Digital Level



11. Apply pressure on the base for 30 seconds, then wait 15-30 minutes for the camera base adhesive to set.

12. Connect the camera to the VRDU (Video Radar Detection Unit).

13. Fit the top of the camera into the two tabs on the camera base. See Fig. 12.

IMPORTANT: Take care when snapping the camera into the lower mounting notch. If the notch is damaged, the camera base must be replaced.

14. Tilt the bottom of the camera forward until it snaps into the lower mounting notch. See Fig. 13.

Pages Freightliner Service Bulletin, September 2016



04/09/2015

1. Tabs


1546154

Fig. 12, Camera Base Tabs



04/09/2015

1. Base Mounting Tabs 2. VRDU camera 3. VRDU Connector

54-291 Freightliner

Service Bulletin

1546155

Fig. 13, VRDU camera Installed

15. Attach the camera cover to the base by first aligning the bottom mounting tabs then gently rotating the cover upwards, taking care to position the connector cable so that it feeds through the opening at the top of the cover.

Warranty This is an informational bulletin only. Warranty does not apply.

Freightliner Service Bulletin, September 2016 Page9

f Place this edge against the right side of the windshield center rubber sealf for parameter 0004472751

Place this edge 4 inches (100mm) from the right of the windshield center rubber seal for parameter 0004473651

n C - I

I [Tl JJ [Tl

n C -I

I [Tl JJ [Tl -

n C -I

I [Tl JJ [Tl

-"O cij" n <ll ,-+ :::r ;;;· <ll Cl..

'° <ll OJ

'° OJ :5· "' ,.... t:: -0 -0 <ll -,

~ :5· Cl..

"' :::r !:E.. Cl.. -, t:: Cl" Cl" <ll -,

"' <ll !:!!.. -

CUT HERE

detroit assurance lane departure warning camera 54-29110.1 hold the digital level used in step 5 up...

Documents