developments in bulk material elevation technology peter wypych, peter olds, robert olds and richard...
TRANSCRIPT
![Page 1: Developments in Bulk Material Elevation Technology Peter Wypych, Peter Olds, Robert Olds and Richard McIntosh](https://reader030.vdocument.in/reader030/viewer/2022032702/56649ca75503460f949697f5/html5/thumbnails/1.jpg)
Developments in Bulk Material Elevation
Technology
Peter Wypych, Peter Olds,
Robert Olds and Richard McIntosh
![Page 2: Developments in Bulk Material Elevation Technology Peter Wypych, Peter Olds, Robert Olds and Richard McIntosh](https://reader030.vdocument.in/reader030/viewer/2022032702/56649ca75503460f949697f5/html5/thumbnails/2.jpg)
Elevation of bulk materials Essential requirement in many industrial plants and processes
Current popular methods:
Introduction
PneumaticConveyor
Dilute Dense
ScrewConveyor
BucketElevator
![Page 3: Developments in Bulk Material Elevation Technology Peter Wypych, Peter Olds, Robert Olds and Richard McIntosh](https://reader030.vdocument.in/reader030/viewer/2022032702/56649ca75503460f949697f5/html5/thumbnails/3.jpg)
However Problems & Limitations :1. Pneumatic Conveying:
Relatively high op. costs, velocities, wear rates and particle damage (esp. dilute)
2. Screw Conveying: Relatively high op. speeds (slippage) and
particle attrition Back-flow of material Undesirable casing/screw contact
3. Bucket Elevators: Relatively high capital/maintenance costs Mistracking of belt/chain Damage to belt/chain, buckets, casing…
Introduction...
![Page 4: Developments in Bulk Material Elevation Technology Peter Wypych, Peter Olds, Robert Olds and Richard McIntosh](https://reader030.vdocument.in/reader030/viewer/2022032702/56649ca75503460f949697f5/html5/thumbnails/4.jpg)
![Page 5: Developments in Bulk Material Elevation Technology Peter Wypych, Peter Olds, Robert Olds and Richard McIntosh](https://reader030.vdocument.in/reader030/viewer/2022032702/56649ca75503460f949697f5/html5/thumbnails/5.jpg)
Also Fire & Explosion Hazards :1. Increased risk of dust explosion due to:
Mech damage or impact Sparking Overheating bearings/pulleys Ignition Bucket-product shearing Frictional heating
2. Dust clouds inside elevator
3. Dust generation mechanisms: Particle-particle & particle-wall impacts Particle attrition Turbulence and induced/entrained air
4. Propagation of dust explosion Elevator
Expensive Explosion control req’d: Venting, Suppression, Isolation…
Introduction...
![Page 6: Developments in Bulk Material Elevation Technology Peter Wypych, Peter Olds, Robert Olds and Richard McIntosh](https://reader030.vdocument.in/reader030/viewer/2022032702/56649ca75503460f949697f5/html5/thumbnails/6.jpg)
Product Explosion Barriers or “Chokes” [2]
![Page 7: Developments in Bulk Material Elevation Technology Peter Wypych, Peter Olds, Robert Olds and Richard McIntosh](https://reader030.vdocument.in/reader030/viewer/2022032702/56649ca75503460f949697f5/html5/thumbnails/7.jpg)
Novel type of elevator (Olds Elevator) Developed to overcome or avoid problems:
New Elevation Technology
External Bearingand Drive
(not shown)
Screw Flight(stationary)
AnnularClearance
Casing(rotating)
In-FeedScoops
In-FeedScoops
![Page 8: Developments in Bulk Material Elevation Technology Peter Wypych, Peter Olds, Robert Olds and Richard McIntosh](https://reader030.vdocument.in/reader030/viewer/2022032702/56649ca75503460f949697f5/html5/thumbnails/8.jpg)
Stationary screw, Rotating casing, Compact design
External bearing/s and Drive (not in contact with bulk material)
Self-feeding Accurate feed rate control (excellent
turndown ratio) Generous clearances No back-flow (loss) of material
Unique Design and Operating Characteristics
![Page 9: Developments in Bulk Material Elevation Technology Peter Wypych, Peter Olds, Robert Olds and Richard McIntosh](https://reader030.vdocument.in/reader030/viewer/2022032702/56649ca75503460f949697f5/html5/thumbnails/9.jpg)
Greater transport efficiency (c/w conv. vertical screws)
Full-bore mode of flow (smooth, steady and no “pulses”)
Suitable for powders and granular materials Minimal particle attrition and dust
generation (even with fragile particles) Can handle difficult, hot, abrasive or
corrosive bulk materials
Unique Design and Operating Characteristics...
![Page 10: Developments in Bulk Material Elevation Technology Peter Wypych, Peter Olds, Robert Olds and Richard McIntosh](https://reader030.vdocument.in/reader030/viewer/2022032702/56649ca75503460f949697f5/html5/thumbnails/10.jpg)
Unique Design and Operating Characteristics...
ConventionalVertical Screw
Olds Elevator(full-bore flow)
![Page 11: Developments in Bulk Material Elevation Technology Peter Wypych, Peter Olds, Robert Olds and Richard McIntosh](https://reader030.vdocument.in/reader030/viewer/2022032702/56649ca75503460f949697f5/html5/thumbnails/11.jpg)
Repeatability Tests – Sulphur Pastilles
(standard elevator)
1500
1520
1540
1560
1580
1600
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Test Number
So
lids
Mas
s F
low
Rat
e (k
g/h
)
Average
+0.5%
- 0.5%
Design enhancements Better accuracy
![Page 12: Developments in Bulk Material Elevation Technology Peter Wypych, Peter Olds, Robert Olds and Richard McIntosh](https://reader030.vdocument.in/reader030/viewer/2022032702/56649ca75503460f949697f5/html5/thumbnails/12.jpg)
Case Studies
Original Elevator
(foundry sand)
![Page 13: Developments in Bulk Material Elevation Technology Peter Wypych, Peter Olds, Robert Olds and Richard McIntosh](https://reader030.vdocument.in/reader030/viewer/2022032702/56649ca75503460f949697f5/html5/thumbnails/13.jpg)
2 Olds Elevators replaced 3 Bucket Elevators and 1 Inclined Screw
Saved capital, Space & Quieter operation
Bean Growers
![Page 14: Developments in Bulk Material Elevation Technology Peter Wypych, Peter Olds, Robert Olds and Richard McIntosh](https://reader030.vdocument.in/reader030/viewer/2022032702/56649ca75503460f949697f5/html5/thumbnails/14.jpg)
Difficult/costly product change-over Extra conveyor needed Dedicated bucket elevator & Inefficient operation
Carbo Ceramics(before)
![Page 15: Developments in Bulk Material Elevation Technology Peter Wypych, Peter Olds, Robert Olds and Richard McIntosh](https://reader030.vdocument.in/reader030/viewer/2022032702/56649ca75503460f949697f5/html5/thumbnails/15.jpg)
Fast change-over and clean-up times No particle damage or dust 35 t/h
Carbo Ceramics(after)
![Page 16: Developments in Bulk Material Elevation Technology Peter Wypych, Peter Olds, Robert Olds and Richard McIntosh](https://reader030.vdocument.in/reader030/viewer/2022032702/56649ca75503460f949697f5/html5/thumbnails/16.jpg)
New test rig at UoW Explore full potential of Olds Elevator:
Further Research
Recirculation (demo) Mode
In-feed scoop designs Screw flight designs Capacity modelling Material property effects
(d, s, , w, etc)
![Page 17: Developments in Bulk Material Elevation Technology Peter Wypych, Peter Olds, Robert Olds and Richard McIntosh](https://reader030.vdocument.in/reader030/viewer/2022032702/56649ca75503460f949697f5/html5/thumbnails/17.jpg)
1. New type of Elevator avoids many problems experienced by traditional equipment (bucket, screw, pneumatic conveyors)
2. Due to its full-bore mode flow: Transport efficiency increased Explosion ignition/propagation hazards avoided Expensive explosion control equip avoided
3. External bearings: Minimise mtce costs; Allow handling of difficult, hot and abrasive bulk materials
4. Particle damage/dust generation minimised
Conclusions