die casting-power-point
TRANSCRIPT
![Page 1: Die casting-power-point](https://reader034.vdocument.in/reader034/viewer/2022042602/55a690c01a28aba0418b4624/html5/thumbnails/1.jpg)
Die CastingDie Casting
By Jonathan Gordon By Jonathan Gordon and Leeand Lee
![Page 2: Die casting-power-point](https://reader034.vdocument.in/reader034/viewer/2022042602/55a690c01a28aba0418b4624/html5/thumbnails/2.jpg)
Gravity Die CastingGravity Die Casting
![Page 3: Die casting-power-point](https://reader034.vdocument.in/reader034/viewer/2022042602/55a690c01a28aba0418b4624/html5/thumbnails/3.jpg)
Gravity die casting Gravity die casting processprocess
Mazak, an alloy of Zinc and aluminium, is first Mazak, an alloy of Zinc and aluminium, is first melted in a crucible furnace.melted in a crucible furnace.
Molten metal is then poured by ladle in to an Molten metal is then poured by ladle in to an open steel mould where it is allowed to cool and open steel mould where it is allowed to cool and solidify.solidify.
![Page 4: Die casting-power-point](https://reader034.vdocument.in/reader034/viewer/2022042602/55a690c01a28aba0418b4624/html5/thumbnails/4.jpg)
Gravity die casting processGravity die casting process
The mould is then turned upside down and The mould is then turned upside down and tapped with a hammer to release the finished tapped with a hammer to release the finished casting.casting.
Gravity die casting requires minimal finishing Gravity die casting requires minimal finishing and waste as minimal because excess metal can and waste as minimal because excess metal can be melted down and used again.be melted down and used again.
![Page 5: Die casting-power-point](https://reader034.vdocument.in/reader034/viewer/2022042602/55a690c01a28aba0418b4624/html5/thumbnails/5.jpg)
Things that you may recogniseThings that you may recognise
Things that are made from gravity die Things that are made from gravity die casting are:casting are:
Toaster - Toaster -
Lawnmowers - Lawnmowers -
Car wheel rims - Car wheel rims -
![Page 6: Die casting-power-point](https://reader034.vdocument.in/reader034/viewer/2022042602/55a690c01a28aba0418b4624/html5/thumbnails/6.jpg)
Identifying the process Identifying the process
When something has been created by When something has been created by gravity pressure die casting there would gravity pressure die casting there would be:be:
Section hair lines Section hair lines ejector pin marksejector pin marks sprue and runner markssprue and runner marks
![Page 7: Die casting-power-point](https://reader034.vdocument.in/reader034/viewer/2022042602/55a690c01a28aba0418b4624/html5/thumbnails/7.jpg)
Materials Materials
The materials used in gravity die casting The materials used in gravity die casting is a mixture of Zinc and aluminium. is a mixture of Zinc and aluminium.
Zinc - Zinc -
Aluminium - Aluminium -
![Page 8: Die casting-power-point](https://reader034.vdocument.in/reader034/viewer/2022042602/55a690c01a28aba0418b4624/html5/thumbnails/8.jpg)
High pressure High pressure die castingdie casting
![Page 9: Die casting-power-point](https://reader034.vdocument.in/reader034/viewer/2022042602/55a690c01a28aba0418b4624/html5/thumbnails/9.jpg)
High Pressure Die CastingHigh Pressure Die Casting
Forcing metal under high pressure to Forcing metal under high pressure to form a mould.form a mould.
These moulds are called dies and are made These moulds are called dies and are made from steel. from steel.
This produces non-ferrous metals.This produces non-ferrous metals.
![Page 10: Die casting-power-point](https://reader034.vdocument.in/reader034/viewer/2022042602/55a690c01a28aba0418b4624/html5/thumbnails/10.jpg)
Materials usedMaterials used
Metals that are commonly used are also: Aluminium -
Zinc -
![Page 11: Die casting-power-point](https://reader034.vdocument.in/reader034/viewer/2022042602/55a690c01a28aba0418b4624/html5/thumbnails/11.jpg)
What is made from the processWhat is made from the process
In this process you can make:In this process you can make:
Golf club heads -Golf club heads -
Car engine blocks - Car engine blocks -
Radiators -Radiators -
![Page 12: Die casting-power-point](https://reader034.vdocument.in/reader034/viewer/2022042602/55a690c01a28aba0418b4624/html5/thumbnails/12.jpg)
High pressure die casting High pressure die casting processprocess
First the mould is sprayed with First the mould is sprayed with lubricant and closed. lubricant and closed.
Molten metal is then injected into Molten metal is then injected into the mould under high pressure. the mould under high pressure.
![Page 13: Die casting-power-point](https://reader034.vdocument.in/reader034/viewer/2022042602/55a690c01a28aba0418b4624/html5/thumbnails/13.jpg)
High pressure die casting High pressure die casting processprocess
Once the cavity is filled, the pressure is Once the cavity is filled, the pressure is kept at a steady level until the casting has kept at a steady level until the casting has become solid.become solid.
Finally, the die is opened and the casting Finally, the die is opened and the casting
is injected.is injected.
![Page 14: Die casting-power-point](https://reader034.vdocument.in/reader034/viewer/2022042602/55a690c01a28aba0418b4624/html5/thumbnails/14.jpg)
Identifying the processIdentifying the process
When something has been created dy When something has been created dy high pressure die casting there would high pressure die casting there would also be:also be:
Section hair lines Section hair lines ejector pin marksejector pin marks sprue and runner marks sprue and runner marks