disassemble and assembly of samsung gt-c3010s
DESCRIPTION
Learn how to disassemble and re assemble a Samsung GT-C3010S mobile for cleaning and repairs. It is a very comprehensive guide to do the job.TRANSCRIPT
SAMSUNG Proprietary-Contents may change without notice
11. Disassembly and Assembly Instructions
11-1
This Document can not be used without Samsung's authorization
11-1. Disassembly
1) Be careful not to make scratch and molding damage! 1) Be careful not to make scratch and molding damage!
1) Be careful not to make scratch and molding damage! 1) Be careful not to make scratch and molding damage!
Remove screw at 4 points (torque:1.0~1.2)1 2 Disjoint the Rear case from the lower part
3 Disassemble volume key from PBA Disassemble the top of the front (4point)4
1
2
3
SAMSUNG Proprietary-Contents may change without notice
Exploded View and Parts List
11-2
This Document can not be used without Samsung's authorization
1) Be careful not to make scratch and molding damage!
2) Be careful not to make damage to SIDE KEY FPCB !
3) Be careful not to make damage to LCD FPCB !
1) Be careful not to make scratch and molding damage!
1) Be careful not to make scratch and molding damage!1) Be careful not to make scratch and molding damage!
2) Be careful not to make damage to key FPCB !
5 Disassemble PBA and front cover(1) Disassemble PBA and front cover(2)6
7 Disassembled PBA and front cover(3) 8 Remove screws at 3 points((torque:1.0~1.2)
and disassemble key FPCB
SAMSUNG Proprietary-Contents may change without notice
Exploded View and Parts List
11-3
This Document can not be used without Samsung's authorization
1) Be careful not to make scratch and molding damage!
2) Be careful not to make damage to camera FPCB !
1) Be careful not to make scratch and molding damage!
2) Be careful not to make damage to motor wire !
1) Be careful not to make scratch and molding damage!
2) Be careful not to make damage to speaker FPCB !
9 Disassemble the Camera by lifting the bottom
of Camera
Disassemble the Motor by lifting the bottom of
Motor
10
11 Disassemble Speaker from PBA
SAMSUNG Proprietary-Contents may change without notice
Exploded View and Parts List
11-4
This Document can not be used without Samsung's authorization
1) Be careful not to make scratch and molding damage!
2) Be careful not to make damage to side key FPCB !
3) Be careful not to make damage to motor wire !
1) Be careful not to make scratch and molding damage!
2) Be careful not to make damage to speaker FPCB !
1) Be careful not to make scratch and molding damage!1) Be careful not to make scratch and molding damage!
2) Beware that you do not damage camera F-PCB.
11-2. Assembly
1 2Solder the side key FPCB and Vibration Motor Solder the Speaker FPCB
3 1) Put Bond on the Motor Solder pad
2) Turn the Motor and Put the Motor in Motor
Bracket
(Remove a release paper.)
Remove a
release paper.
4 1) Insert camera FPCB depending on silk line.
2) Insert camera in speaker bracket.
(Remove a release paper.)
Remove a
release paper.
SAMSUNG Proprietary-Contents may change without notice
Exploded View and Parts List
11-5
This Document can not be used without Samsung's authorization
1) Be careful not to make scratch and molding damage! 1) Be careful not to make scratch and molding damage!
1) Be careful not to make scratch and molding damage!
2) Be careful not to make damage on Side key FPCB!
(in the red box)
1) Be careful not to make scratch and molding damage!
2) Beware that you do not damage LCD F-PCB.
5 1) Drivers 3 screws on the PBA (torque:1.0~1.2)
2) Insert FPCB of KEY to main PBA. Make
sure that FPCB is completely inserted.
6 1) Check the attached status of keypad on
the front cover
7 Put the PBA on the FRONT part 8 Insert FPCB of LCD to main PBA. Make sure
that FPCB is completely inserted.
SAMSUNG Proprietary-Contents may change without notice
Exploded View and Parts List
11-6
This Document can not be used without Samsung's authorization
1) Be careful not to make scratch and molding damage! 1) Be careful not to make scratch and molding damage!
8 Put the Side key FPCB on the FRONT
then Put the Side Key on the FRONT
10 Combine the REAR with FRONT
from the upper hook to lower hook
(the direction of Red arrow)
10 Drivers 4 screws on the rear (torque:1.0~1.2)