document no. - welcome to dlw official website€¦ · · 2014-11-15document no. qsp- vendor...
TRANSCRIPT
Document No. QSP- Vendor Control Page 2 of 14
Date of Origin - 15.01.2002 Version No.10.0
Effective Date : 25.10.2014 Issued by : MR
1. Purpose & Scope: 1.1 This QSP-Vendor Control is issued in supercession of the earlier QSP-Vendor Control Version 9.2. 1.2 Purpose is to evaluate, enlist, review and control vendors having necessary capability to supply
spares/items required for manufacture and maintenance of diesel locomotives (ALCO and EMD), as per specified requirements, including raw materials, electrodes etc.
1.3 Composite Vendor directory would normally be published in December every year to be effective from 1st January to 31st December of the following year or till publication of next Vendor directory, whichever is later.
2. Responsibility: 2.1 Vendor evaluation, enlistment, review and control are to be dealt with, in accordance with the
procedure given in this QSP. SN Activity Description Responsibility Reference 3. Definitions 3.1 Composite Vendor Directory (CVD)
Vendor directory published by DLW covering items/ spares, raw materials and electrodes required for manufacture/ maintenance of diesel locomotives.
3.2 Developmental order Purchase order for supply of any item, which has not been supplied earlier by the vendor to DLW.
3.3 Extended trial order. Any order placed subsequent to a developmental order on a vendor who is not in approved vendor list.
3.4 Approved “Part-I” vendor: A source for placement of bulk orders for the spare/item approved in accordance with QSP-Vendor control.
3.5 Approved “Part-II” vendor: A source for placement of limited orders for the spare/item approved in accordance with QSP-Vendor control.
3.6 “JAG/SG” Committee A committee consisting of “JAG/SG” officers of Design/Production/ Material Control, Accounts & Stores, nominated by the competent authority as per WI/DES/103. The concerned officer of Design /Prod./ Material Control would be the convener of the committee. 3.7 CME would be approval authority of CVD.
Document No. QSP- Vendor Control Page 3 of 14
Date of Origin - 15.01.2002 Version No.10.0
Effective Date : 25.10.2014 Issued by : MR
SN Activity Description Responsibility Reference
3.8 “PO” means Purchase Order placed by DLW. 3.9 “CPA” means Corrective and Preventive Action taken by DLW as per QSP.
4 Awareness about vendors, Quality Management
System (QMS), VA-1 form and downgrade-tion / delisting / restoration
4.1 DLW becomes aware of vendors based on their participation in a tender or through any other relevant source/method.
4.1.1 New firms base initially have to submit a duly filled and signed VA-1 form to CDE. This information bank is used for evaluating the capability of the vendors if there is a need for development of additional vendors for that item/category of item. The information available in VA-1 form may also be referred during vendor review exercises and technical evaluation of vendor’s offers in tender cases.
4.2 Availability of Quality Management System (QMS) as per IS / ISO 9001:2008 or TS16949 or any equivalent QMS certification is mandatory for enlistment of all new vendors, as well as continuation of part ’II’ vendors in the CVD.
Vendor’s QMS as per ISO:9001/ TS:16949 would be considered only if the scope of certification includes manufacturing of the item under consideration/ similar product(s)/relevant type of manufacturing e.g steel forging, steel casting, heavy fabrication, heavy sheet metal fabrication, precision machining, electrical rotating machines etc, as the case may be. 4.2.1 Existing vendors whose QMS are not certified to ISO 9001: 2008 but approved as Part’I’ in the composite vendor directory, their vendor status may be reviewed and downgraded to part ‘II’ and advised to obtain the same within next six months, failing which they may be delisted. However their vendor status may be restored to part ‘I’, once they submit proof of having obtained ISO 9001:2008 or equivalent certificate to CDE/CME(P)/ CME(M),DLW (as the case may be).
Concerned Design/Prod/MC/Purchase Officer
Concerned Design/Prod/MC Officer Concerned Design/Prod/MC Officer Concerned Design/Prod/MC Officer
Document No. QSP- Vendor Control Page 4 of 14
Date of Origin - 15.01.2002 Version No.10.0
Effective Date : 25.10.2014 Issued by : MR
SN Activity Description Responsibility Reference
4.2.2 Existing Part II vendors, who do not have a QMS, as indicated in Para 4.2, shall be included in the CVD provisionally and the vendor would be informed accordingly, that the requisite certification should be obtained within six months otherwise they shall be delisted from the CVD. However their vendor status would be restored to part ‘II’, once they submit proof of having obtained ISO 9001:2008 or equivalent certificate to CDE/CME(P)/ CME(M),DLW (as the case may be) Competent authority of restoration of vendor status after receipt of necessary QMS certificate will be CDE/CME(P)/CME(M), DLW (as the case may be). If QMS Certificate of International vendor is not available, waiver may be granted with the approval of CDE/CME(M)/CME(P) (as the case may be).
4.3 Micro and Small Enterprises (MSEs) status of vendors shall be provided by Stores Department against the column 13 of Annexure A & B. (Railway Board’s letter No. 2001/RS(G)/779/7 dated 08.08.2014) 4.4 Existing approved vendors shall be required to resubmit the VA-I at interval of every 05 years. Their failure to submit VA-1, may lead to their status being reviewed and downgraded one step (delisting in case of Part ‘II’ approved source and down grading to part ’II’ in case of part ’I’ approved source). For this also, the process as indicated at para 5.1 and 5.3 shall be followed. However, a Part ‘I’ approved vendor, for an item under review, shall be downgraded only if, at least two other Part I sources are available. A Part-II approved vendor for an item under review shall be delisted only if at least three other sources are available in PartI/PartII. Further a vendor delisted / downgraded due to non availability of VA-1 form, may be restored to original vendor status, if they submit a duly completed VA-1 form to Design / Dy.CME / Loco/ Block/ MC office (as the case may be).
Competent authority of restoration of vendor status
Concerned Design/Prod/MC Officer Stores member of JAG/SG committee Concerned design/prod/MC officer Concerned Design/Prod/MC Officer.
Document No. QSP- Vendor Control Page 5 of 14
Date of Origin - 15.01.2002 Version No.10.0
Effective Date : 25.10.2014 Issued by : MR
SN Activity Description Responsibility Reference
after receipt of valid VA-1 will be CDE/CME(P)/CME(M), DLW (as the case may be). If VA-1 form of a vendor of International/ National repute/original design holder is not available, waiver may be granted with the approval of CME. This may be initiated by CDE/CME(M)/CME(P) (as the case may be) and put up for CME’s approval.
4.5 Design Office would check the completeness of information/documents submitted by the vendor in / along with filled-up VA-I forms.
Concerned Design/Prod/MC Officer.
Concerned Design/Prod/MC Officer
5. Process to be followed for enlistment / upgradation / delisting / downgradati on / restoration of vendors in CVD.
5.1 There are 560 “Simple” items defined in Annexure F. These Simple items follow the following criteria:
The manufacturing process is simple is a simple one which will not need proving out by design office.
The application is such where normally design intervention is not needed for assembly and where field prove out is not required.
They will not normally affect the safety and reliability of the locomotive.
Evaluation of vendors for enlistment in DLW Vendor Directory will be done by design office (concerned Dy.CDE) after due assessment of the firm’s infrastructure, capability, capacity, quality system and its credentials, The recommendations will be made by CDE and approved by CME. (Refer W/DES/114 for the approval criteria) 5.2 For the balance items, evaluation of vendors for enlistment in DLW Vendor Directory as Part-II or Part-I source will be done jointly by ‘JAG/SG’ committee. All such proposals will be put up to CME/P for Electrodes (Block), Electrodes (Loco) items, CME/M for Raw Materials and CDE for rest of the items for compilation and scrutiny. Then, their recommendation of CDE would be sent to CME for final consideration and approval. The concerned conveners of the JAG/SG committees would forward the cases to CDE, after CME’s
Concerned DyCDE
CDE Concerned JAG/SG Committee
Document No. QSP- Vendor Control Page 6 of 14
Date of Origin - 15.01.2002 Version No.10.0
Effective Date : 25.10.2014 Issued by : MR
SN Activity Description Responsibility Reference
approval for publication of Composite Vendor Directory / issue of monthly supplement.
The above process of review and approval of vendor status for any item shall be followed for vendor review exercises for the purpose of upgradation, delisting, downgradations and restoration in CVD too.
5.2.1 For this purpose, review shall be initiated by the concerned convener of the JAG/SG committees. A detailed tabulated statement shall be prepared as per the format prescribed at Annexure-A of this QSP. Convener of the JAG/SG committee shall furnish information in Column 01 to 12. Stores member shall furnish information in Column 13 to 15. Column 16 to 19 shall be filled jointly by the JAG/SG committee’s members. 5.2.2 Certain items which are not complex, are similar in application and design and require the same process, skills and infrastructure have been clubbed together for vendor evaluation purpose. These items would be called “generic “ items and would require tabulation as per Annex B of this QSP. Convener of the JAG/SG committee shall furnish information in Column 01 to 12. Stores member shall furnish information in Column 13 to 15. Column 16 to 19 shall be filled jointly by the JAG/SG committee’s members.
5.2.3 There are items required by Zonal Railways which are not procured by DLW but which have been included in the CVD on Railway Board instructions (defined in Annexure E) . These would require tabulation as per Annexure C of this QSP. Convener of the JAG/SG committee shall furnish information in Column 01 to 12. Column 13 to 16 shall be filled jointly by the JAG/SG committee’s members. The
upgradation /inclusion in these items shall be considered by the JAG/SG committee on the basis of an application made to CDE /DLW, by the vendor for this purpose after he has satisfied the requirements herein laid down for such inclusion/upgradation.
CDE
Concerned JAG/SG Committee Concerned JAG/SG Committee
Concerned JAG/SG Committee
Document No. QSP- Vendor Control Page 7 of 14
Date of Origin - 15.01.2002 Version No.10.0
Effective Date : 25.10.2014 Issued by : MR
SN Activity Description Responsibility Reference
5.2.4 Successful execution of 2 POs for DLW or successful service of 10 loco sets for six months shall make a Vendor eligible for consideration for Part-II approval. However, quality of items supplied by the vendor and supply performance shall also be considered by the committees while recommending enlistment as Part-II source. 5.2.5 In the case of generic items the proven credentials of a firm against any one items of the subgroup being considered enabler for similar items across the group, the recommendation for Part-II would normally extend to the complete group 5.2.6 For zonal railway spares, not being procured by DLW (defined in annexure E) successful execution of 2 POs to Zonal Railways shall make a vendor eligible for consideration to Part-II status. 5.2.7 For certain items defined in Annexure D, minimum loco sets/ minimum service life criteria will be used for upgradation in Part-II. However, vendor’s quality and supply performance shall also be considered by the committees while recommending enlistment as Part-II source. 5.3 Successful execution of at least 1 PO for DLW after enlistment in Part-II category or successful supply of 20 loco sets with satisfactory service of 10 loco sets for one year shall make a vendor eligible for consideration for upgradation/ inclusion to Part-I category following the same procedure given in Para 5.2 above. However, vendor’s quality and supply performance shall also be considered by the committees while recommending enlistment as Part-I source. 5.3.1 In the case of generic items, the proven credentials of a firm against any one items of the subgroup being considered enabler for similar items across the group, the recommendation for Part-I would normally extend to the complete group.
Concerned JAG/SG Committee Concerned Design/Prod/MC Officer CDE
Concerned JAG/SG Committee Concerned JAG/SG Committee Concerned JAG/SG Committee Concerned Design/Prod/MC Officer CDE
Document No. QSP- Vendor Control Page 8 of 14
Date of Origin - 15.01.2002 Version No.10.0
Effective Date : 25.10.2014 Issued by : MR
SN Activity Description Responsibility Reference
5.3.2 For certain items defined in Annexure D, minimum loco sets / minimum service life criteria will be used for upgradation/inclusion in Part-I. However, vendor’s quality and supply performance shall also be considered by the committees while recommending enlistment as Part-I source. No vendor shall be deemed to qualify for Part-I status unless he fulfills the quantity & service life criteria for part-II. 5.3.3 For zonal railway spares not being procured by DLW, minimum loco sets/minimum loco years criteria defined in Annexure-E will be used for considering upgradation / inclusion to Part-I. 5.4 The supplied quantity of an item would “deemed to complete” the qualifying service life criteria, once it completes “T+4 months” from the date of accepted supply i.e. date of receipt order (where T is the qualifying service life of that item) 5.5 Direct enlistment in Part-II or Part-I, even without execution of any PO, as a special case, can also be considered at the time of review. However, the reviewing committee / CDE/ CME(P)/CME(M) shall clearly bring out the reason (s) for such a recommendation for consideration / comments/ approval at higher levels(s).
5.6 Authorized agents/representatives/traders shall not be enlisted as approved vendors. Only OEMs/Manufacturers would be enlisted as approved source in vendor directory. However, to facilitate issue of tender inquiry, authorized agent’s/ representative’s / traders name and address may also be indicated in a separate column on address page based on exclusive authorization of the manufacturer for the product under consideration on a year-to-year basis. The authorization should be valid for the period for which approval is being recommended / given.
Concerned JAG/SG Committee Concerned JAG/SG Committee Concerned JAG/SG Committee Concerned JAG/SG Committee CDE/CME(P)/ CME(M)
Concerned Design/Prod/MC Officer
6. Review of vendor status
6.1 Consolidated review for “Simple” items at annexure F shall be done once in a year for
Concerned DyCDE
Document No. QSP- Vendor Control Page 9 of 14
Date of Origin - 15.01.2002 Version No.10.0
Effective Date : 25.10.2014 Issued by : MR
SN Activity Description Responsibility Reference
for inclusion/ upgradation/ delisting/ downgradatio n in CVD
inclusion/ upgradation in Composite vendor Directory at the time of publishing. The concern DyCDE can however, during the course of the year recommend inclusion / upgradation of vendors to tide over problems of non availability of material due to inadequate vendors. Such a review will be authorized by CDE or CME. 6.2 Consolidated review for "Annexure D " items shall be done once in a year for inclusionI upgradation in Composite Vendor Directory at t he time of publishing. However mid term review of "Annexure D" items for upgradation/inclusion in DLW Vendor Directory shall also be done on the basis of an application made to GM/CME/CDE by the vendor for this purpose.
6.3 For the balance items review shall generally be done once in a year for inclusion/Upgradation in Composite Vendor Directory at the time of publishing. However in special circumstances based on the need expressed by GM/CME/COS/ FA&CAO / CME(P) / CDE / CME(M) / CQAM/ CMM(Engine) / CMM(Loco) / CMM(HQ) / FA&CAO (TOT) intermediate review shall be carried out. Applications/ expression of need shall be forwarded to the concerned convener(s) of the JAG/SG Committee by CDE. Thereafter, where the change in status is warranted, the procedure laid down in para 5.2 & 5.3 above shall be followed. 6.4 For Zonal Railway spare items not being procured by DLW and defined in Annexure E, inclusion/upgradation would be processed annually on the basis of vendor application only. Application shall be given to GM/CME/CDE who shall forward the same to the concerned convener(s) of the JAG/SG Committee. Thereafter, the procedure laid down in para 5.2 and 5.3 above, shall be followed. 6.5 At the time of recommending inclusion / upgradation of a vendor for any item, the convener
Convener DyCDE Concerned JAG/SG Committee
Convener JAG/SG Committee Concerned JAG/SG
Document No. QSP- Vendor Control Page 10 of 14
Date of Origin - 15.01.2002 Version No.10.0
Effective Date : 25.10.2014 Issued by : MR
SN Activity Description Responsibility Reference
of the JAG/SG committee shall ensure that completed VA-1 form of the vendor is available. However if the same is not available, and it is observed that vendor is of international / national repute / original design holder, then the same may be brought out by JAG/SG committee during review for consideration as per para 4.4.
6.6 For approved vendors, review for deletion / downgradation shall be done, as and when required, and issued through monthly supplements as reviewed by the committees and approval of CME as laid down under para 5.1, 5.2 and 5.3 above.
The review may be undertaken under following conditions: - i. Poor supply performance ii. On the basis of field feedback received from Railway Board, RDSO, Zonal Railways, Diesel Sheds received directly or through SIG cell, Non Railway Customers (including foreign Railway customers) through marketing.
iii. Poor quality as reported by Shops/ Quality control organization. iv. Withdrawal of ISO:9001 or equivalent certificate by the certifying body.
v. The vendor is black listed / or business dealing is banned by Govt. of India or its offices on communication by Railway Board. In such cases, no show cause notice to the firm is required. However, intimation shall be given.
vi. The vendor is suspended for a defined period due to unbecoming conduct. (Suspension can be authorized by the authority competent to
Committee Concerned MC / Purchase officer / Dy.CMM/Depot / user Dy.CME to initiate.
Concerned Design / Production / MC officer
Concerned Design/Prod/MC officer Concerned JAG/SG Committee Concerned JAG/SG Committee
Concerned Design /
Document No. QSP- Vendor Control Page 11 of 14
Date of Origin - 15.01.2002 Version No.10.0
Effective Date : 25.10.2014 Issued by : MR
SN Activity Description Responsibility Reference
approve it). vii. If the specification or drawing is revised and the vendor is not upgrading the additional requirements of infrastructure, M&P, testing facilities, qualified personnel etc. within specified time frame. 6.7 The effective date of monthly supplements shall be the 1st day of the month in which amendment has been issued.
6.8 Before deletion/down-gradation of any vendor, a show-cause notice shall be given to the vendor enumerating the reasons for doing so and seeking for his representation, if any, within 21 days from the date of issue of the notice (not required if notice has already been issued / vendor advised in past for not having QMS as per ISO 9001:2008 or any equivalent certification). After receipt of vendor’s reply or expiry of show-cause notice period whichever is earlier, the case shall be put up to the concerned JAG/SG committee for review by the officer sending the show-cause notice. After review the case shall be dealt with in accordance with procedure given in para 5.2 above.
6.9 A firm once downgraded / delisted on account of any issue except non submission of VA-1 & QMS certificate, shall not be considered for upgradation/inclusion for next one year (from the effective date of CVD / monthly supplement).
Production / MC officer
Concerned Design / Production / MC officer DyCDE/Eng Concerned JAG/SG Committee Concerned JAG/SG Committee
7. Communica
-tion to control copy holders & Vendors
7.0 Communication to control copy holders & vendor(s) 7.1 Whenever a vendor is downgraded or delisted for any reason, whatsoever, a letter shall be sent to the vendor, indicating the reason, thereof. Information shall also be sent to all the control copy holders of the composite vendor directory, either in the form of monthly supplements to composite vendor directory or new composite vendor directory itself.
Concerned Design/Prod/MC officer
Document No. QSP- Vendor Control Page 12 of 14
Date of Origin - 15.01.2002 Version No.10.0
Effective Date : 25.10.2014 Issued by : MR
SN Activity Description Responsibility Reference 7.2 Vendor(s) shall also be informed about their enlistment / upgradation. All control copy holders of the composite vendor directory, shall also be informed either through monthly supplements to composite vendor directory or new composite vendor directory itself. However in this case giving reason thereof is not necessary. 7.3 Whenever the status of a vendor is restored, as indicated at para 4.2 & 4.4, again the vendor shall be informed through a letter. Information shall also be sent to all the control copy holders of the composite vendor directory, either in the form of monthly supplements to composite vendor directory or new composite vendor directory itself. 7.4 CVD shall be uploaded on the DLW website (www.dlw.indianrailways.gov.in) and updated periodically after issue of amendments.
Concerned Design/Prod/MC officer. Concerned Design/Prod/MC officer. Concerned Design officer
8 Change in name / Work Address of the vendor:
8.1 Request of vendor for change of name: On receipt of request from the vendor for change of name, which is already on the approved vendor list, the same shall be affected after verification of the vendor’s premises and documentation by the nominated DLW officials. If the DLW official is satisfied, based on the scrutiny of documents like memorandum of article of association, list of tools, plants and machinery, undertaking by the new vendor for liability of old firm, resolution by board of directors, partnership deed, Certificate of Registrar of companies etc., he / she shall recommend for the change of name of the vendor through the concerned JAG/SG committee after taking clearance of Law branch (Legal cell) as per procedure given in the para 5.2. 8.2 Change in name in case of bifurcation of works: If change of name is done as a result of bifurcation of existing work premises, in addition to checking of documents as given in para 8.1, reassessment shall also be carried out by a DLW official before effecting the change of name of the vendor.
Concerned Design/Prod/MC officer. Concerned Design/Prod/MC officer. Concerned Design/Prod/MC officer.
Document No. QSP- Vendor Control Page 13 of 14
Date of Origin - 15.01.2002 Version No.10.0
Effective Date : 25.10.2014 Issued by : MR
SN Activity Description Responsibility Reference 8.3 Request of vendor for change in address: On receipt of request of the vendor for change of address, the nominated DLW official shall verify that:
a) The office establishment has been shifted totally.
b) The machinery & plants have been shifted totally.
c) Informations given in the updated and completed VA-1 are correct.
Competent authority for change of vendor address will be CDE/CME(P)/CME(M), DLW (as the case may be)
8.4 Request of vendor for enlistment of their additional works: Vendor shall inform DLW about the operations and processes to be followed in their additional works through additional / revised VA-1 form. Then the nominated DLW official shall verify the availability of necessary M&Ps, measuring/ testing equipments etc at the new premises. Competent authority for enlistment of vendor’s additional works will be CDE/CME(P)/CME(M), DLW (as the case may be)
8.5 Submission of updated VA-1 form: Vendor shall submit updated copy of VA –1 form with new name/ new address / new works to the concerned officer of Design/ Production/MC. 8.6 Communication to Vendor: The vendor shall be informed in writing that the change of name / change of address / enlistment of new works has been noted by DLW. The changed name shall be advised to all copyholders of the CVD. Vendor Directory shall be amended accordingly. 8.7 Change of both name and address shall not be permitted at the same time. 8.8 Actions as per paras 8.2 to 8.4 shall be taken in consultation with Legal cell of DLW whenever required.
Concerned Design/Prod/MC officer.
Concerned Design/Prod/MC officer. Concerned Design/Prod/MC officer. Concerned Design/Prod/MC officer. Concerned Design/Prod/MC officer.
9.0 Notwithstanding anything mentioned in the clauses of this QSP vendor Control (version 9.2), any vendor
Concerned JAG / SG Committee
Document No. QSP- Vendor Control Page 14 of 14
Date of Origin - 15.01.2002 Version No.10.0
Effective Date : 25.10.2014 Issued by : MR
SN Activity Description Responsibility Reference
becoming eligible for inclusion/upgradation for an item as per the earlier version of QSP Vendor Control (version 8.0) will also be included/ upgraded for the said item. This provision will remain effective upto 31st December 2015.
Linkage: - Apex Manual: Purchasing W/DES/103 W/DES/114
Annexure ‘A’ to QSP – Vendor Control (Version 10.0)
S. No. Part No. Part Description Existing Part-I vendor(s)
Existing Part-II vendor(s)
Name of vendors not having QMS as per ISO-9001 or equivalent
Name of vendors whose ISO-9001 or equivalent certification has expired (validity upto)
1 2 3 4 5 6 7
Whether this item / product group/ manufacturing process is covered under the scope of ISO-9001 or equivalent certificate of the vendor
Name of vendors whose VA-1 form is not available. Also specify if waiver is taken
Proforma-A / RI-30 information (for last one year)
Performance feedback from Railways/ Shops/QA organization/RDSO etc.
Any other information available with Design/MC/Production Office
Status of MSEs of Vendors
Names of all vendors who have supplied this item to DLW (with nos. of POs executed)
8 9 10 11 12 13 14 Supply performance of vendors (to DLW)
Deliberations of JAG/SG committee
Proposed Revised Vendor Status (Part-I)
Proposed Revised Vendor Status (Part-II)
Remarks (if any)
15 16 17 18 19
Annexure ‘B’ to QSP – Vendor Control (Version 10.0)
S. No. Part No. Part Description Existing Part-I vendors
Existing Part-II vendors
Name of vendors not having QMS as per ISO-9001 or equivalent
Name of vendors whose ISO-9001 or equivalent certification has expired (validity upto)
1 2 3 4 5 6 7
Whether this item / product group/ manufacturing process is covered under the scope of ISO-9001 or equivalent certificate of the vendor
Name of vendors whose VA-1 form is not available. Also specify if waiver is taken
Proforma-A / RI-30 information (for last one year)
Performance feedback from Railways/ Shops/QA organization/RDSO etc.
Any other information available with Design/MC/Production Office
Status of MSEs of Vendors
8 9 10 11 12 13 Names of unapproved vendors who have supplied any of the items to DLW in the last 5 years (with nos. of PO executed)
Supply performance of approved vendors of the group in the last 2 years (to DLW)
Deliberations of JAG/SG committee
Proposed Revised Vendor Status (Part-I)
Proposed Revised Vendor Status (Part-II)
Remarks (if any)
14 15 16 17 18 19
Annexure ‘C’ to QSP – Vendor Control (Version 10.0)
S. No. Part No. Part Description Existing Part-I vendors
Existing Part-II vendors
Name of vendors not having QMS as per ISO-9001 or equivalent
Name of vendors whose ISO-9001 or equivalent certification has expired (validity upto)
1 2 3 4 5 6 7
Whether this item / product group/ manufacturing process is covered under the scope of ISO-9001 or equivalent certificate of the vendor
Name of vendors whose VA-1 form is not available. Also specify if waiver is taken
Performance feedback from Railways/ Shops/QA organization/RDSO etc.
Any other information available with Design Office
If any application made by vendor for inclusion / upgradation
Deliberations of JAG/SG committee
8 9 10 11 12 13 Proposed Revised Vendor Status (Part-I)
Proposed Revised Vendor Status (Part-II)
Remarks (if any)
14 15 16
Annexure D to QSP Vendor Control Version 10.0
SN Part Description Part No. Qualifying Quantity & Period for Part-II Qualifying Quantity & Period for Part-I
1 Gauge 4” Control Air 11445555 10 loco sets(10 nos) to complete 01 year service 30 loco sets (30 nos)2 Gauge 4” Duplex Air Pressure ( MR & FP) 11445476 10 loco sets(20 nos) to complete 01 year service 30 loco sets (60 nos)3 Gauge 4” Single Air Pressure (BC) 11445488 10 loco sets(20 nos) to complete 01 year service 30 loco sets (60 nos)4 Gauge 4” Single Air Pressure (MR) 11445490 10 loco sets(10 nos) to complete 01 year service 30 loco sets (30 nos)5 Gauge 6” Single pressure (B.P) 11445518 10 loco sets(20nos) to complete 01 year service 30loco sets (60 nos)6 Gauge Booster Air 11445543 10 loco sets(10 nos) to complete 01 year service 30 loco sets (30 nos)7 Gauge Fuel Oil 11440417 10 loco sets(10 nos) to complete 01 year service 30 loco sets (30 nos)8 Gauge lube oil. 11440429 10 loco sets(10 nos) to complete 01 year service 30 loco sets (30 nos)9 Turbo charger 2300 HP 10082438/
1008245110 Turbo charger 1350 HP 10083704
11 Gear Camshaft 16140310 10 loco sets(20 nos) to complete 06 months service 40 loco sets (80 nos)12 Gear Crank shaft 1614026613 Gear Drive 24 teeth Gov. Drive 1614104014 Gear Lower Idler 1614121015 Gear Ring 1619190016 Gear Turbo Drive 1614098917 Gov. Drive Gear Asm 1605042318 Upper Idler Gear Asm 1605051919 Gear Carrier Drive 1621042620 Gear Planetary Ring 1614119221 Gear Turbo idler 1614149022 Gear Asm accessory Drive 1603056423 Gear ASM –Acc Drive 1605001024 Planet Gear Set 16210207 10 loco sets(10 nos) to complete 06 months service 40 loco sets (40 nos)25 Alco loco DBR with Hatch Assly 12002616 05 loco sets(05 nos)to complete 06 months service 10 loco sets (10 Nos) & 05 loco sets to
complete 02 years service26 Crank Shaft 6 Cyl. 10141110 05 loco sets (05 nos) to complete 02 years service 30 loco sets (30 nos) & 05 loco sets to
complete 03 years service
27 Bushing (Cam Shaft)* 10150080 03 loco Sets ( 54 nos) to complete 01 year service 30 loco sets (540 nos)28 Bushing (Piston Pin)* 10150092 03 loco Sets ( 48 nos) to complete 01 year service 30 loco sets (480 nos)29 Bushing Out Board Bearing Hsg 10150833 05 loco Sets ( 10 nos) to complete 01 year service 30 loco sets (60 nos)30 Bearing Half-Camshaft* 16150119 10 loco Sets ( 40 nos) to complete 01 year service 30 loco sets (120 nos)
31 Bearing Half-Camshaft* 16150120 10 loco Sets ( 40 nos) to complete 01 year service 30 loco sets (120 nos)
32 Bearing Blower End (Tri Lobe)* 10150766 10 loco Sets (10 nos) to complete 01 year service 30 loco sets (30 nos)33 Bearing Turbine End (Tri Lobe)* 10150742 10 loco Sets (10 nos) to complete 01 year service 30 loco sets (30 nos)34 Bearing Turbine* 16150454 10 loco Sets (10 nos) to complete 01 year service 30 loco sets (30 nos)
35 Bearing Compressor sfd.* 16150284 10 loco Sets (10 nos) to complete 01 year service 30 loco sets (30 nos)
36 Bearing Spherical Seal* 16150442 10 loco Sets (10 nos) to complete 01 year service 30 loco sets (30 nos)37 Bearing* 16150430 10 loco Sets (30 nos) to complete 01 year service 30 loco sets (90 nos)38 Flange* 16080634 10 loco Sets (10 nos) to complete 01 year service 30 loco sets (30 nos)
10 loco sets(10 nos) to complete 06 months service 40 loco sets (40 nos)
List of Items with Minimum Quantity and Service life Criteria
10 locos sets (10 nos ) to complete 01 year service 30 loco sets (30 nos) &
05 loco sets to complete 03 years service
Page 1 of 8
Annexure D to QSP Vendor Control Version 10.0
SN Part Description Part No. Qualifying Quantity & Period for Part-II Qualifying Quantity & Period for Part-I
List of Items with Minimum Quantity and Service life Criteria
39 Bearing Insert* 16150090 03 loco Sets (48 nos) to complete 01 year service 30 loco sets (480 nos)40 Bearing Thrust* 16150314 10 loco Sets (20 nos) to complete 01 year service 30 loco sets (60 nos)41 Bushing-Camshaft Br.* 16150144 03 loco Sets (192 nos) to complete 01 year service 30 loco sets (1920 nos)
42 Bearing 16150247 10 loco Sets (20 nos) to complete 01 year service 30 loco sets (60 nos)
43 Bearing-Idler G 16150235 10 loco Sets (10 nos) to complete 01 year service 30 loco sets (30 nos)
44 Bearing-Idler G 16150223 10 loco Sets (10 nos) to complete 01 year service 30 loco sets (30 nos)45 Aftercooler Asm 16080919 10 loco Sets (20 nos) to complete 01 year service 30 loco sets with 40 nos to complete 01
year of service46 Lube oil cooler 17050534 10 loco Sets (10 nos) to complete 06 months service 30 loco sets with 20 nos to complete 01
year of service47 Fuel Pump Motor 1.5 HP 75 Volts DC 12102076 10 loco Sets (10 nos) to complete 06 months service 30 loco sets(30 nos) with 20 nos to
complete one year of service48 A.C.Fuel Pump Motor 12102120 10 loco Sets (10 nos) to complete 06 months service 30 loco sets (30 nos) & 05 loco sets to
complete 02 years service49 AC Dust Collector Blower(LH) 11665324 10 loco Sets (10 nos) to complete 06 months service 30 loco sets (30 nos) & 05 loco sets to
complete 02 years service50 AC Dust Collector Blower(RH) 11665312 10 loco Sets (10 nos) to complete 06 months service 30 loco sets (30 nos) & 05 loco sets to
complete 02 years service51 A.C.Crank Case Motor 12102131 10 loco Sets (10 nos) to complete 06 months service 30 loco sets (30 nos) & 05 loco sets to
complete 02 years service52 Crank Case Exhauster
Unit(B.G.) DC 12100249 10 loco Sets (10 nos) to complete 06 months service 30 loco sets(30 nos) with 20 nos to
complete one year of service53 Crank Case Exhauster
Unit(M.G.) DC 12100250 10 loco Sets (10 nos) to complete 06 months service 30 loco sets(30 nos) with 20 nos to
complete one year of service54 Blower Motor Sch.No. 000221/ EL/PT/0624 12100213 10 loco Sets (10 nos) to complete 06 months service 30 loco sets (30 nos) & 02 loco sets to
complete 02 years service55 Dynamic Brake Grid Sch.No. 00224 12242172 10 loco Sets (10 nos) to complete 06 months service 30 loco sets(30 nos) with 20 nos to
complete one year of service56 Eddy Current Clutch Sch.No. 00005 /
EL/PT/063712440127 10 loco Sets (10 nos) to complete 06 months service 30 loco sets(30 nos) with 20 nos to
complete one year of service57 Eddy Current Clutch Sch.No. 00005 A 12440115 10 loco Sets (10 nos) to complete 06 months service 30 loco sets(30 nos) with 20 nos to
complete one year of service58 Axle Generator 12060069 10 loco Sets (10 nos) to complete 06 months service 30 loco sets(30 nos) with 20 nos to
complete one year of service59 Techo Generator 12060057 10 loco Sets (10 nos) to complete 06 months service 30 loco sets(30 nos) with 20 nos to
complete one year of service60 Blower Motor 17050054 10 loco Sets (10 nos) to complete 06 months service 30 loco sets (30 nos) & 02 loco sets to
complete 02 years service61 Motor Out Line TLPM (DC Motor) 16060222 10 loco Sets (10 nos) to complete 06 months service 30 loco sets(30 nos) with 20 nos to
complete one year of service62 Connecting Rod & Cap Integral 10142083 05 loco Sets (80 nos) to complete 01 year service 30 loco sets(480 nos) 63 Modified Larger After Cooler 10082785 10 loco Sets (10 nos) to complete 01 year service 30 loco sets with 20 nos to complete 01
years service
Page 2 of 8
Annexure D to QSP Vendor Control Version 10.0
SN Part Description Part No. Qualifying Quantity & Period for Part-II Qualifying Quantity & Period for Part-I
List of Items with Minimum Quantity and Service life Criteria
64 Exh. Manifold Assly. (16 Cyl.Eng) 10080892 10 loco Sets (10 nos) to complete 06 months service 20 loco sets(20 nos) to complete one year of service
65 Main Base 10021267 10 loco Sets (10 nos) to complete 06 months service 20 loco sets(20 nos)66 Machining of Con Rod ASM 10030050 05 loco Sets (80 nos) 30 loco sets(480 nos)67 Crankcase Machining ASM 16020017 05 loco Sets (05 nos) to complete 01 year service 20 loco sets (20 nos) & 02 loco sets to
complete 02 years service
68 Exhaust Manifold Ap 16360175 10 loco Sets (10 nos) to complete 06 months service 20 loco sets(20 nos) to complete one year of service
69 Camshaft Asm-LB 16030308 05 loco Sets (05 nos) to complete 01 year service 30 loco sets(30 nos)70 Camshaft Asm-RB 16030310 05 loco Sets (05 nos) to complete 01 year service 30 loco sets(30 nos)71 Clutch Dowelling ASM 17240074 05 loco Sets (05 nos) to complete 01 year service 30 loco sets(30 nos)72 Con Rod-Blade 16140308 05 loco Sets (40 nos) to complete 01 year service 30 loco sets(240 nos)73 Con Rod ASM-Fork 16030059 05 loco Sets (40 nos) to complete 01 year service 30 loco sets(240 nos)74 Spring Exhaust Valve 16160034 05 loco Sets (480 nos) to complete 01 year service 30 loco sets(2880 nos)75 Valve-Exhaust 16240066 05 loco Sets (320 nos) to complete 01 year service 30 loco sets(1920 nos)76 Cylinder Liner ASM* 16030035 05 loco Sets (80 nos) to complete 01 year service 30 loco sets(480 nos)77 Cylinder Liner Stud ASM* 19110017 10 loco Sets (160 nos) to complete 01 year service 30 loco sets(480 nos)78 Oil Pan Machining Asm 16020534 10 loco Sets (10 nos) to complete 06 months service 20 loco sets(20 nos) 79 Radiator Mechanical Bonded 11458227 10 loco Sets (10 nos) to complete 01 year service 30 loco sets (30 nos) & 05 loco sets to
complete 02 years service
80 Bonded Rubber Sandwitch Mounting 11270019 05 loco Sets (30 nos) to complete 01 year service 20 loco sets (120 nos)81 Traction Motor Blower (Rear & Front) 11434466
110522841145852511055870
05 loco Sets (05 nos) to complete 01 year service 30 loco sets(30 nos) with 20 nos to complete one year of service
82 Brake Cylinder MTG 'X' 11360239 10 loco Sets (40 nos) to complete 01 year service 30 loco sets (120 nos)83 Brake Cylinder MTG 'Z' 11360227 10 loco Sets (40 nos) to complete 01 year service 30 loco sets (120 nos)84 Main Reservoir 350 lts.(LH) MR-I 11377860 10 loco Sets (10 nos) to complete 01 year service 30 locosets (30 nos)85 Main Reservoir 350 lts.(RH) MR-II 11374032 10 loco Sets (10 nos) to complete 01 year service 30 locosets(30 nos)86 Main Reservoir 350 lts.(RH) MR-II 11663522 10 loco Sets (20 nos) to complete 01 year service 30 locosets (60 nos)87 Floor Frame Assly (WDM3D) 11531137 10 loco Sets (10 nos) to complete01 year service 20 loco sets (20 nos) & 05 loco sets to
complete 02 years service
88 Fuel Tank Asm for WDG4 17030845 10 loco Sets (10 nos) to complete 01 year service 20 loco sets (20 nos) & 05 loco sets to complete 02 years service
89 After Cooler Finned ASM 17452193 10 loco Sets (10 nos) to complete 06 months service 20 loco sets (20 nos) to complete 01 years service
90 Reservoir Main For WDG4 17450986 10 loco Sets (20 nos) to complete 01 years service 30 locosets (60 nos)91 Underframe Asm 17030857 10 loco Sets (10 nos) to complete 01 year service 20 loco sets (20 nos) & 05 loco sets to
complete 02 years service
Page 3 of 8
Annexure D to QSP Vendor Control Version 10.0
SN Part Description Part No. Qualifying Quantity & Period for Part-II Qualifying Quantity & Period for Part-I
List of Items with Minimum Quantity and Service life Criteria
92 Underframe Asm 17036586 10 loco Sets (10 nos) to complete 01 year service 20 loco sets (20 nos) & 05 loco sets to complete 02 years service
93 Underframe Kit for WDG4 17031667 10 loco Sets (10 nos) 20 loco sets (20 nos)94 Kit for Underframe Asm of WDG4D Dual Cab 17036670 10 loco Sets (10 nos) 20 loco sets (20 nos)95 TURBO DOWELLING ASM 16080579 10 loco Sets (10 nos) to complete 06 months service 20 loco sets (20 nos) to complete 01 year
service96 TURB WHL-IMPLR BAL ASM 16080385 10 loco Sets (10 nos) to complete 01 year service 20 loco sets (20 nos) & 05 loco sets to
complete 3 years service97 CONTROL CONSOL NO. 1 (WDG4) 18000060 10 loco Sets (10 nos) to complete 06 months service 20 loco sets (20 nos) & 02 loco sets to
complete 01 year service
98 CONTROL CONSOL NO. 2 (WDG4) 18000071 10 loco Sets (10 nos) to complete 06 months service 20 loco sets (20 nos) & 02 loco sets to complete 01 year service
99 BOOSTER PUMP & MOTOR ASSY 16241526 10 loco Sets (10 nos) to complete 06 months service 30 loco sets (30 nos) & 05 loco sets to complete 02 year service
100 PISTON PIN* 16141441 05 loco Sets (80 nos) to complete 01 year service 30 loco sets (480 nos) 101 ENGINE COUPLING DISC 16191882 10 loco Sets (10 nos) to complete 06 months service 40 loco sets (40 nos)102 LUBE OIL SCAVENGING PUMP ASM. 16060090 10 loco Sets (10 nos) to complete 06 months service 30 loco sets (30 nos) & 05 loco sets to
complete 02 years service103 LUBE OIL PRESSURE PUMP ASM. 16060027 10 loco Sets (10 nos) to complete 06 months service 30 loco sets (30 nos) & 05 loco sets to
complete 02 years service104 Soak Back Pump ASM 16060210 10 loco Sets (10 nos) to complete 06 months service 30 loco sets (30 nos) & 05 loco sets to
complete 02 years service
105 CYL POWER ASM-BLADE* 16350029 05 loco Sets (40 nos) to complete 01 year service 30 loco sets (240 nos)
106 LOCOMOTIVE SPEED SENSOR (RADAR ASSEMBLY)
18030294 10 loco Sets (10 nos) to complete 06 months service 20 loco sets (20 nos) loco sets to complete 01 year service
107CYL POWER ASM-FORK* 16350017 05 loco Sets (40 nos) to complete 01 year service 30 loco sets (240 nos)
108 UNLOADER PANEL ASSEMBLY 17062263 10 loco Sets (10 nos) to complete 01 year service 20 loco sets (20 nos) to complete 01 year service
109 CAM SHAFT BLOCK & CAP ASM KIT 16030540 10 loco Sets (10 nos) to complete 06 months service 20 loco sets (20 nos) to complete 01 year service
110 BRAKE RIGGING KIT 17021182 10 loco Sets (10 nos) to complete 01 year service 30 loco sets (30 nos)111 BRAKE RIGGING KIT 17022678 10 loco Sets (10 nos) to complete 01 year service 30 loco sets (30 nos)112 BRAKE CYLINDER 17020890 10 loco Sets (40 nos) to complete 01 year service 30 loco sets (120nos)113 PIVOT ASM. 17020270 10 loco Sets (20 nos) to complete 01 year service 30 loco sets (60 nos)114 CONTROL CONSOLE OF CAB-1 FOR
DUAL CAB LOCOMOTIVE18002365 10 loco Sets (10 nos) to complete 06 months service 20 loco sets (20 nos) & 02 loco sets to
complete 01 year service115 CONTROL CONSOLE OF CAB-2 FOR
DUAL CAB LOCOMOTIVE18002677 10 loco Sets (10 nos) to complete 06 months service 20 loco sets (20 nos) & 02 loco sets to
complete 01 year service
Page 4 of 8
Annexure D to QSP Vendor Control Version 10.0
SN Part Description Part No. Qualifying Quantity & Period for Part-II Qualifying Quantity & Period for Part-I
List of Items with Minimum Quantity and Service life Criteria
116CYLINDER BLOCK ASSLY. 10021437
05 loco Sets (05 nos) to complete 01 year service 20 loco sets (20 nos) & 02 loco sets to complete 02 year service
117 LONG HOOD STRUCTURE ASM 17041983 10 loco Sets (10 nos) to complete 06 months service 20 loco Sets (20 nos) 118
ENGINE WDG4 1601008510 Engines to complete 01 year service 20 Engines and 05 Engines to complete 3
years service
119TURBO INLET SCROLL ASM 16080701
10 loco Sets (10 nos) to complete 06 months service 20 loco sets (20 nos) to complete 01 years service
120UNDER FRAME ASM FOR WDP4D 17033135
10 loco Sets (10 nos) to complete 01 year service 20 loco sets (20 nos) and 05 loco sets to complete 02 years service
121T.M. AIR DUCT ASM 17031904
10 loco Sets (60 nos) to complete 01 year service 20 loco sets (120 nos) to complete 03 years Service
122 RETAINER CYLINDER HEAD 16020091 10 loco Sets (160 nos) to complete 06 months service 20 loco sets (320 nos)123 CAB STRUCTURE 17044698 10 loco Sets (10 nos) to complete 06 months service 20 loco sets (20 nos) 124
CAMSHAFT DRIVE HOUSING M/C ASM 1603041210 loco Sets (10 nos) to complete 06 months service 30 loco sets (30 nos) with 05 nos to
complete 01 years service125 CHANNEL 16191780 10 loco Sets (40 nos) to complete 06 months service 20 loco sets (80 nos)126
FRAME & LATCH ASSLY LB 1603033310 loco Sets (10 nos) to complete 06 months service 30 loco sets (30 nos) with 05 loco sets (05
nos ) to complete 01 years service127
LUBE OIL STAINER ASM. 1606011810 loco Sets (10 nos) to complete 06 months service 20 loco sets (20 nos) to complete 01 years
service128
FRAME & LATCH ASSLY RB 1603038210 loco Sets (10 nos) to complete 06 months service 30 loco sets (30 nos) with 05 loco sets (05
nos ) to complete 01 years service129
UNDERFRAME (WDG3A) 1103616310 loco Sets (10 nos) to complete 01 year service 20 loco sets (20 nos) and 05 loco sets to
complete 02 years service130
COVER ACCESSORY DRIVE 1613022410 loco Sets (10 nos) to complete 06 months service 30 loco sets (30 nos) with 05 nos to
complete one year of service131
16 CYLINDER ENGINE BLOCK (ENVE 1002001905 loco Sets (05 nos) to complete 01 year service 20 loco Sets (20 nos) and 02 loco sets to
compelete 02 years service132
COVER AND SEAL ASSLY 1603027810 loco Sets (40 nos) to complete 06 months service 30 loco Sets (120 nos) with 05 loco sets
(20 nos) to complete 01 years service133
ROCKER ARM SUB ASM- EXHAUST 1604004110 loco Sets (320 nos) to complete 06 months service 20 loco sets (640nos) to complete 01 years
service134 AUX.GEN.DRIVE ASM 16080040 10 loco Sets (10 nos) to complete 06 months service 30 loco sets (40 nos)135
PAD ASM-LAT THRUST 1702024410 loco Sets (120 nos) to complete 01 year service 20 loco sets (240 nos) to complete 03
years service136 Pad Asm Lateral thurst 17022708 10 loco Sets (120 nos) to complete 01 year service 20 loco sets (240 nos) to complete 03
years service137
FUEL INJ NOZZLE & HOLDER 1005002410 loco Sets (160 nos) to complete 06 months service 20 loco sets (320 nos) to complete 01
years service138
EXPANSION JOINT ASM 1624077710 loco Sets (30 nos) to complete 01 year service 40 loco sets (120 nos) with 10 loco sets
(30 nos.) to complete 02 years service139
CLUTCH DRIVE ASM. 1606049010 loco Sets (10 nos) to complete 01 year service 20 loco sets (20 nos) & 05 loco sets to
complete 03 years service
Page 5 of 8
Annexure D to QSP Vendor Control Version 10.0
SN Part Description Part No. Qualifying Quantity & Period for Part-II Qualifying Quantity & Period for Part-I
List of Items with Minimum Quantity and Service life Criteria
140FUEL PUMP 17454633
10 loco Sets (10 nos) to complete 01 year service 30 loco sets (30 nos) and 05 loco sets to complete 2 years service
141IDLER-STUBSHAFT ASM 16030473
10 loco Sets (10 nos) to complete 06 months service 20 loco Sets (20 nos) to complete 01 years service
142NOZZLE RING 16080610
10 loco Sets (10 nos) to complete 01 year service 20 loco Sets (20 nos) to complete 01 years service
143 AIR DUCT ASM.(RB) 16080063 10 loco Sets (10 nos) to complete 06 months service 30 loco sets (30 nos) 144
FUEL INJECTION PUMP 1005219710 loco Sets (160 nos) to complete 06 months service 20 loco sets (320 nos) to complete 01
years service145
FLOOR FRAME ASSLY(WDS6AD) 1153478310 loco Sets (10 nos) to complete 01 year service 10 loco sets (10 nos) and 05 loco sets to
complete 2 years service146
ROLLER ASM. CAM FOLLOWER 1614035710 loco Sets (480 nos) to complete 06 months service 20 loco sets (960 nos) with to complete 01
years service147 AIR DUCT ASM.(LB) 16080105 10 loco Sets (10 nos) to complete 06 months service 30 loco sets (30 nos) 148
DAMPER ASSEMBLY 1603002305 loco Sets (05 nos) to complete 01year service 20 loco sets (20 nos) to complete 01 years
service149 PLATE CAM 16140837 10 loco Sets (10 nos) to complete 01 years service 40 loco sets (40 nos)150 TOP DECK END ROUGH FORGING 16140096 10 loco Sets (20 nos) to complete 06 months service 20 loco sets (40 nos)151 Top Deck Centre rough forging 16140102 10 loco Sets (10 nos) to complete 06 months service 20 loco sets (20 nos)152 INLET TUBE ASM 16050253 10 loco Sets (160 nos) to complete 01 year service 40 loco sets (640 nos) 153 TUBE ASM 16060271 10 loco Sets (160 nos) to complete 01 years service 20 loco sets (320 nos) 154
DIFFUSER ASM 1612176410 loco Sets (10 nos) to complete 06 months service 20 Loco Sets (20 nos) to complete 01
years service155
ROCKER ARM SUB AY-I 1604012010 loco Sets (160 nos) to complete 06 months service 20 loco sets (320 nos) to complete 01
years service156
EXHAUST DUCT ASM 1608045210 loco Sets (10 nos) to complete 06 months service 20 Loco Sets (20 nos) to complete 01
years service157
F/PUMP & T/SOAKBACK PUMP MOTOR 1810002810 loco Sets (10 nos) to complete 06 months service 30 Loco Sets (30 nos) and 05 Loco sets to
complete 2 years service158
SUPPORT DRIVE 1614039410 loco Sets (10 nos) to complete 06 months service 40 Loco Sets (40 nos) with 20 nos to
complete 01 years service159 AFTER COOLER CORE 16080531 10 loco Sets (10 nos) to complete 01 year service 40 Loco Sets (40 nos)160 COVER ASM HAND HOLE 16020406 10 loco Sets (310 nos) to complete 06 months service 20 Loco Sets (620 nos)161 COVER ASM HAND HOLE 16020522 10 loco Sets (10 nos) to complete 06 months service 20 Loco Sets (20 nos)162 MAIN FRAME MEMBER KIT 16241083 10 loco Sets (10 nos) to complete 06 months service 20 Loco Sets (20 nos)163
SUPPORT - ROCKER ARM 1613003010 loco Sets (320 nos) to complete 06 months service 20 Loco Sets (640 nos) to complete 01
years service164
AIR VALVE 1024580710 loco Sets (320 nos) to complete 06 months service 30 loco sets (960 nos) to complete 01
years service165
EXPANSION JOINT ASM 1624080710 loco Sets (10 nos) to complete 01 year service 40 Loco Sets (40 nos) & 10 loco sets (10
nos.) to complete 02 years service166
VALVE BRIDGE ASSEMBLY 1604005310 loco Sets (320 nos) to complete 06 months service 20 Loco Sets (640 nos) to complete 01
years service
Page 6 of 8
Annexure D to QSP Vendor Control Version 10.0
SN Part Description Part No. Qualifying Quantity & Period for Part-II Qualifying Quantity & Period for Part-I
List of Items with Minimum Quantity and Service life Criteria
167SHAFT CARRIER 16210190
10 loco Sets (10 nos) to complete 06 months service 30 Loco Sets (30 nos) to complete 01 years service
168CORE LUBE OIL COOLER 17453252
10 loco Sets (10 nos) to complete 01 year service 30 loco sets with 20 nos to complete 01 years service
169SHROUD ASSLY 16080488
10 loco Sets (10 nos) to complete 06 months service 20 Loco Sets (20 nos) to complete 01 years service
170ROCKER ARM ASM-INJ R/C SN. 241 16040119
10 loco Sets (160 nos) to complete 06 months service 20 Loco Sets (320 nos) to complete 01 years service
171 CAB STRUCTURE KIT FOR P4D 17045277 10 loco Sets (10 nos) to complete 06 months service 20 Loco Sets (20 nos) 172 KIT FOR UNDERFRAME FOR WDP4D 17033421 10 loco Sets (10 nos) 20 Loco Sets (20 nos)173 LONGHOOD STRUCTURE - WDP4D 17045307 10 loco Sets (10 nos) to complete 06 months service 20 Loco Sets (20 nos) 174
FUEL TANK ASM 5000 LTR 1703343310 loco Sets (10 nos) to complete 01 year service 20 Loco Sets (20 nos) and 05 Loco sets to
complete 2 years service175 LED BASED CAB LIGHT WITH SPOT
LIGHT18361353
20 nos to complete 06 months service 40 nos with 20 nos to complete 01 year service
176COOLING FAN 18650016
20 nos to complete 06 months service 40 nos with 20 nos to complete 01 year service
177PANEL EQUIPMENT 17042630
10 loco Sets (10 nos) to complete 06 months service 20 loco Sets (20 nos) to complete 01 year service
178PANEL EQUIPMENT 18200011
10 loco Sets (10 nos) to complete 06 months service 20 loco Sets (20 nos) and to complete 01 year service
179SENSOR ASM 1000 RTD 18640023
10 loco Sets (10 nos) to complete 06 months service 20 loco Sets (20 nos) to complete 01 year service
180AIR DIFFUSER SCH. NO.00206/EL/PT/0660 12479032
10 loco Sets (10 nos) to complete 06 months service 20 loco sets (20 nos) to complete 01 years service
181CAB HEATER SPEC. NO. WDG4/EL/PS/29 18280031
10 nos to complete 06 months service20 to complete one years service
182 AIR WHISTLE TO DRG NO 10585230 17451243 10 loco sets (20 nos) to complete 01 year service 30 loco sets (30 nos)183 AIR START RESERVOIR TO DRG NO.
40175322
17456228 10 loco sets (10 nos) to complete 01 years service 30 loco sets (30 nos)
184 BRAKE SHOE KEY TO DRG. NO. 9501303 17453227 10 loco sets (120 nos) to complete 01 years service 30 loco sets (360 nos)
185 BRAKE RIGGING KIT 11520334 10 loco sets (10 nos) to complete 01 years service 30 loco sets (30 nos)186 BRAKE RIGGING KIT 11020428 10 loco sets (10 nos) to complete 01 years service 30 loco sets (30 nos)187 CATTLE GUARD ASSLY TO DRG NO TPL-
0788
11033617 10 loco sets (20 nos) to complete 01 years service 30 loco sets (30 nos)
188 MODIFIED CATTLE GUARD ASSEMBLY 17032969 10 loco sets (20 nos) to complete 01 years service 30 loco sets (30 nos)
189 CATTLE GUARD ASSEMBLY 17035909 10 loco sets (20 nos) to complete 01 years service 30 loco sets (60 nos)190 MODIFIED HAND BRAKE 11669160 10 loco sets (10 nos) to complete 01 year service 30 loco sets (30 nos)
191 HANDBRAKE TO DRG NO. 10634750 17020025 10 loco sets (10 nos) to complete 01 year service 30 loco sets (30 nos)192 WIPER MOTOR ASM KIT CONSISTING 04
ITEMS
17454955 20 nos to complete 01 year service 60 nos and 20 nos to complete 02 years
service.
Page 7 of 8
Annexure D to QSP Vendor Control Version 10.0
SN Part Description Part No. Qualifying Quantity & Period for Part-II Qualifying Quantity & Period for Part-I
List of Items with Minimum Quantity and Service life Criteria
193 WIPER MOTOR ASM KIT CONSISTING OF
05 ITEMS
17454967 20 nos to complete 01 year service 60 nos and 20 nos to complete 02 years
service.194 DEE SHACKLE WITH CONNECTION PIN
TO DRG NO TPL- 5438
11026224 10 loco sets (80 nos) to complete 01 years service 30 loco sets (240 nos)
195 SHACKLE ASSLY TO DRG NO TPL- 2745 11028646 10 loco sets (80 nos) to complete 01 years service 30 loco sets (240 nos)
196 SHACKLE ASSLY 17020645 10 loco sets (80 nos) to complete 01 years service 30 loco sets (240 nos)197 BRAKE HEAD ASSEMBLY 17020440 10 loco sets (120 nos) to complete 01 years service 30 loco sets (360 nos)198 SEC LATERAL STOP 17455777 10 loco sets (40 nos) to complete 01 years service 30 loco sets (120 nos)199 LATERAL THRUST PAD TO EMD DRG NO.
40162354
17272956 10 loco sets (120 nos) to complete 01 year service 30 loco sets (360 nos) to complete 03 year
service200 LINK MACH TO DRG NO 40076440 17980951 10 loco sets (60 nos) to complete 01 year service 30 loco sets (180 nos)201 NOSE LINK ASM 17021741 10 loco sets (60 nos) to complete 06 months service 30 loco sets (180 nos)202 TRACTION ROD ASM TO DRG NO.
40172456
17021637 10 loco sets (120 nos) to complete 01 year service 30 loco sets (360 nos) to complete 02 year
service203 GEAR CASE ASSLY. WITH HARDWARE,
FELT SEAL GASKETS AND TPU SEAL
(TOP & BOTTOM) DRG NO 12087841
12087841 10 loco sets (60 nos) to complete 01 year service 30 loco sets (180 nos)
204 GEAR CASE ASSLY KIT TO DRG NO. K-
1745012
17453793 10 loco sets (60 nos) to complete 01 year service 30 loco sets (180 nos)
*A mimimum of 02 loco sets shall be required to be open at least after 02 years of service and examined for their condition before placing the product in question in Part-I category
Page 8 of 8
Annexure-E to QSP-Vendor Control(Version 10.0)
SN PART DESCRIPTION PART NO QUALIFYING QTY(NOS) FORUPGRADATION TOPART-I
1 Special Plug 10210532 202 Arm Assly 10050826 303 Bearing Carrier (T.E.) 10121195 304 Bottom Cover F.P.Support 10240019 20 loco sets5 Branch Pipe (Modified) LS 10125220 206 Branch Pipe (Modified) RS 10125218 207 Bushing A.C.C. Device 10130032 30 loco sets8 Bushing F.P. Cam Roller 10211160 4809 Bushing F.P. Cam Roller 10211731 48010 Cam Roller (A & E) 10216844 96011 Cam Roller (F.P. Cross Head Lifter) 10216832 48012 Cam Roller F.P. Cross Head 10211767 48013 Cam Roller, F.P. Cross Head 10211238 48014 Cam Roller, Push Rod 10211226 96015 Cam Spacer 10213065 30 loco sets16 Cam Spacer 10260754 30 loco sets17 Camshaft (Stiffer) LHS 10031340 30 loco sets18 Camshaft (Stiffer) RHS 10031352 30 loco sets19 Casing Water Pump (BG) 10120180 3020 Control Cable End 10211639 2021 Conventional Gear Extension Shaft (P/M) 10143130 2022 Conventional Gear LOP (P/M) 10143117 2023 Conventional Gear WP (P/M) 10143124 2024 Cover Assly. (Exp. Door) 10020184 32025 Cover Assly. L.O.P. & Strainer (Fab. Design) 10062373 30 loco sets26 Cross Hd. Body 10216923 48027 Drive Shaft Assly. L.O.P. (16 Cy. Eng.) 10061277 3028 Drive Shaft Assly. L.O.P. (6 Cy. Eng.) 10060420 3029 Element, Lube Oil Filter (Turbo) 10246642 40030 Flanged Bearing Bushing 10130070 30 loco sets31 Flanged Bearing Bushing 10130081 30 loco sets32 Foundation rail (LS) 12 Cyl. 10261734 2033 Foundation rail (RS) 12 Cyl. 10261722 2034 Fulcrum Pin 10050760 48035 Fulcrum Pin cross Hd. 10211184 48036 Fulcrum Pin cross Hd. Lifter 10216959 48037 Fulcrum Pin Push Rod Lifter 10216947 48038 G.I. Casing (Inner) 16 Cyl. Eng. (Finished) 10120816 3039 G.I. Casing, Outer (Finished) 10120828 3040 Gas Inlet Casing (Less Nozzle Ring) 12 Cyl. (Fab. Design) 10081057 30
41 Gear Casing and Turbo Support (6 Cyl) 10050942 3042 Gear Casing Machined 10121031 3043 Gear Crank Shaft (Finished) 10140463 2044 Gear, Nylon (W.W. Gov.) 10241620 2045 Gland, Expansion Joint 10123969 2046 Heat Shield 10240378 2047 Idler Shaft (BG) High Capacity 10212395 3048 Idler Shaft (BG) Standard Capacity 10210465 3049 Idler Shaft (MG) Modified Design 10211548 3050 Impeller Follower (16 Cyl. ) 10122953 20 sets
Minimum Qty Service life critiria for Part-I for Zonal Rly Items
51 Impeller Follower (6 Cyl. Eng.) to be procured as matching set 10211792 20 sets
52 Insert Snap Ring 15345154 128053 Intermediate Casing Machined ( Cast Design) 10120506 3054 K V Pipe 10060479 20 sets55 Lever Eccentric ( Finished) 10140300 20 sets56 Lifter F.P. Cross Head 16 Cyl. 10140402 32057 Main Casing 10121158 3058 Micro Switch 10240860 2559 Nozzle Ring, 12 Cyl. 10123787 3060 Nut, F.P.S. Cover 10140062 20 loco sets61 Nut, Spl. Fitting 10221244 20 loco sets62 Oil Slinger T.E. (350-B Turbo) 10211469 30 loco sets63 Oil Slinger T.E. (350-C Turbo) 10212220 30 loco sets64 Pin (A & E) 10216870 20 loco sets65 Pin Acc. Device 10211287 20 loco sets66 Pin control Linkage 10210702 20 loco sets67 Pin Fuel Cam Roller 10216881 32068 Pin, Fuel Cam Roller 10211111 32069 Pipe Exhaust Manifold (LS) 10124366 2070 Pipe Exhaust Manifold (RS) 10124342 2071 Pipe Plug 1 1/2" 11291760 20 loco sets72 Pipe Plug 1" 11291722 20 loco sets73 Pipe Plug 3/4" 11291709 20 loco sets74 Plug 1/8" 11304224 20 loco sets75 Plug Indicator 15270105 20 loco sets76 Plunger O.S.T. 10210787 2077 Pump Lube Oil 6 Cyl. 10060418 2078 Shaft Water Pump with Sleeve 10070400 3079 ShaftTurbo (16 Cyl.Eng.) 10140827 3080 Sleeve Fully Finished 10130160 3081 Sleeve Stud 10230567 3082 Slinger (B.E.) 10211433 3083 Spring Retainer 10220010 2084 Thermal Insulation 84134938 20 sets85 Thrust Ball 10211123 64086 Twin After Cooler Core (LHS) 10082669 4087 Twin After Cooler Core (RHS) 10082918 4088 Upper Housing OST 10120105 2089 Valve Guide (Standard) 10120385 320090 V-Band Coupling 10241991 3091 Vibration Damper Cam shaft 10030141 4092 Water Connection Pipe 10071106 2093 Water Connection Pipe (Centre) 10071040 2094 Water Connection Pipe (L.H.) 10071039 2095 Water Connection Pipe (R.H.) 10071090 2096 Water Pump Assly. 16 Cyl. 10070412 3097 Wear Plate 10240202 2098 Wear Plate 10240561 2099 Yoke, Fully Machined 10140323 640100 Fuel Injection Pump 15 MM 10050012 320101 Wear Plate 10130093 20102 Wear Plate 10130100 20
Annexure F to QSP-
vendor control (version
10.0)
SIMPLE ITEMS
SN Description Part No1 Drive Screw 15260010
2 Drive Screw 15262017
3 Drive Screw 15264038
4 Drive Screw 15330345
5 Machine Screw 15151130
6 Machine Screw 15153058
7 Machine Screw 15153060
8 Machine Screw 15153071
9 Machine Screw 15154099
10 Machine Screw 15346092
11 Machine Screw 15657565
12 Machine Screw 15157064
13 Machine Screw 15159050
14 Machine Screw 15159073
15 Machine Screw 15159097
16 Machine Screw 15162072
17 Machine Screw 15162096
18 Machine Screw 15173033
19 Machine Screw 15173057
20 Machine Screw 15174037
21 Machine Screw 15174050
22 Machine Screw 15176071
23 Self Tapping Screw 15205071
24 Self Tapping Screw 15220059
25 Self Tapping Screw 15229117
26 Wood Screw 15230119
27 Stud 15830032
28 Weld Stud 15140040
29 Acom Nut 3/8" - 16 15373125
30 Hex Nut 15367071
31 Hex Nut M 24 15743512
32 Nut 11161656
33 Nyloc Nut 15755095
34 Plain Hex Nut 15366121
35 Weld Nut 15375110
36 Weld Nut 15375109
37 Weld Nut 15375122
38 Weld Nut 15375146
39 Weld Nut 15375160
40 Plain Washer (Steel) 15391085
41 Plain Washer (Steel) 15391103
42 Plain Washer (Steel) 15391115
43 Plain Washer (Steel) 15391164
44 Plain Washer (Steel) 15391188
45 Plain Washer (Steel) 15410080
46 Spring Lock Washer (Special ) 15395303
47 Pop Rivet 11342857
48 Rivet Button Head (Steel) 15343078
49 Rivet Button Head (Steel) 15345075
50 Roll Pin 15330199
51 Hex Nut 15350186
52 Hex Nut 15350228
53 Hex Nut 15366108
54 Hex Nut 15366110
55 Hex Nut 15366145
56 Hex Nut 15380804
57 Hex Nut 15749022
58 Hex Nut 15350204
59 Hex Nut 15369080
60 Hex Nut (Slotted) 15351166
61 Hex Nut (Slotted) 15757067
62 Dowel Pin 10240330
63 Special Dowel 10240299
64 Special Dowel 10210908
65 Special Dowel 10212280
66 Special Dowel 10240287
67 Spring Lock Washer 15790034
68 Spring Lock Washer 15790101
69 Spring Lock Washer 15393203
70 Spring Lock Washer 15393227
71 Spring Lock Washer 15393240
72 Spring Lock Washer 15410602
73 Spring Lock Washer 15396071
74 Spring Lock Washer 15396083
75 Spring Lock Washer 15396101
76 Spring Lock Washer 15396113
77 Spring Lock Washer 15396125
78 Spring Lock Washer 15790071
79 Spring Lock Washer 15790010
80 Spring Lock Washer 15790022
81 Straight Dowel 15300079
82 Straight Dowel (Steel) 15285170
83 Straight Dowel (Steel) 15280081
84 Straight Dowel (Steel) 15281097
85 Straight Dowel (Steel) 15283136
86 Straight Dowel (Steel) 15284177
87 Straight Dowel (Steel) 15284189
88 Straight Dowel (Steel) 15289096
89 Straight Dowel (Steel) 15289151
90 Straight Dowel (Steel) 15300055
91 Taper Dowel 15293075
92 Taper Dowel 15294110
93 Taper Dowel 15295138
94 Taper Dowel 15295151
95 Taper Dowel 15296131
96 Taper Dowel 15296209
97 Taper Dowel 15297135
98 Taper Dowel 15298188
99 Taper Dowel 15299156
100 Taper Dowel 15299170
101 Taper Dowel 15299193
102 Cotter Pin 15329112
103 Cotter Pin 15330618
104 Cotter Pin 15321083
105 Cotter Pin 15330692
106 Cotter Pin 15331556
107 Spiral Pin 15330230
108 Spiral Pin 15330217
109 Spiral Pin 15330229
110 Spiral Pin 15330242
111 Spiral Pin 15330254
112 Spiral Pin 15330278
113 Spiral Pin 15330280
114 Split Cotter Pin 15850237
115 Split Cotter Pin 15850110
116 Flat Key 15310255
117 Flat Key 15311090
118 Flat Key 15312173
119 Flat Key 15315010
120 Flat Key 15315034
121 Flat Key 15312185
122 Key 11190139
123 Key 11190140
124 Key 11190164
125 Key 11190152
126 Shim, Air Compressor 11103942127 Shim, E.C.C. 11105999128 Clamp Assly 17061684129 Clamp assly (Stainless Steel) 11340289130 Clamp Kit 11663923131 Clamp Kit 11668647132 Clamp Kit 11668659133 Clamp Kit 11668660134 Clamp Kit 11668672135 Clamp Kit (Cab & Hood) 11664721136 Clamp Kit (Through Frame) 11664710137 Door Stop assly 17043049138 Hand Rail Arrangement Kit 11530194139 Hand Rail Kit 11531332140 Hinge 11340319141 Hinge 11340320142 Hinge 11340393143 Hinge 11340411144 Hinge Assly 11345779145 Ladder Step 11531691146 Ladder Step 11531812147 Ladder Step 11531824148 Step Tread 17081269149 BAR 17084039150 BLOCK 17083424151 SPACER 17084040152 FOOT 17100173153 FOOT 17083874154 FOOT 17083886
155 STEP TREAD 17451176156 Channel 17127841157 ANGLE 17124475158 ANGLE 17128778159 ANGLE 17150723160 ANGLE 17980197161 ANGLE 17128900162 ANGLE 17120159163 ANGLE 17127350164 ANGLE 17125224165 ANGLE 17127373166 ANGLE 17128043167 ANGLE 17129631168 ANGLE 18460124169 BRACKET 17086486170 BRACKET 17125753171 BRACKET 17124414172 BRACKET 17126691173 BRACKET 17124426174 BRACKET 17126708175 BRACKET 17124890176 BRACKET 17127361177 FLASHING 17085470178 FLASHING 17124736179 FLASHING 17124748180 FLASHING 17124761181 FLASHING 17124621182 FLASHING 17125121183 FLASHING 17125133184 FLASHING 17125145185 FLASHING 17140766186 FLASHING 17125157187 FLASHING 17125169188 FLASHING 17125200189 FLASHING 17125212190 FLASHING 17125170191 FLASHING 17126733192 FLASHING 17980185193 PLATE 17085044194 RETAINER 17125017195 RETAINER 17128262196 RETAINER 17124980197 RETAINER 17124992198 RETAINER 17125005199 RETAINER 17083151200 SHEET 17129928201 SHEET 17124440202 SHEET 17125777203 SHEET 17125789204 SHEET 17125790205 SHEET 17128389206 SHEET 17128894207 SHEET 17126101
208 SHEET 17126745209 SHEET 17128006210 SHEET 17128020211 SHEET 17129394212 SHEET 17128201213 SHEET 17140780214 SHEET 17128213215 SHEET 17128341216 SHEET 17128031217 SHEET 17128171218 SHEET 17128328219 SHEET 17128523220 SHEET 17128614221 SHEET 17129862222 SHEET 17129874223 SHEET 17129886224 STRIP 17124670225 STRIP 17124694226 STRIP 17124580227 STRIP 17126710228 STRIP 17126721229 STRIP 17124682230 STRIP 17125315231 STRIP 17125303232 STRIP 17125327233 STRIP 17125716234 ANGLE 17125406235 ANGLE 17125728236 STRIP 17126824237 ANGLE 17085871238 ANGLE 17085020239 ANGLE 17085883240 ANGLE 17124633241 ANGLE 17124645242 ANGLE 17124487243 ANGLE 17082950244 ANGLE 17124657245 ANGLE 17127440246 ANGLE 17150619247 ANGLE 17150656248 ANGLE 17124190249 ANGLE 17124219250 ANGLE 17129370251 ANGLE 17129667252 BAR 17180090253 BAR 17086061254 BAR 17085068255 BAR 17083436256 BAR 17180107257 BAR 17100070258 BAR 17083333259 BAR 17160479260 BAR 17160480
261 BAR 17083370262 BAR 17083382263 BRACKET 17083035264 BRACKET 17083369265 BRACKET 17126460266 CHANNEL 17150590267 CHANNEL 17150607268 CHANNEL 17150620269 CHANNEL 17129760270 CHANNEL 17150668271 CHANNEL 17127890272 CHANNEL 17083928273 CHANNEL 17083904274 CHANNEL 17083916275 CHANNEL 17083898276 CHANNEL 17085913277 PAD 17084064278 PAD 17083412279 PAD 17083473280 PAD 17083485281 PAD 17083497282 PAD 17083527283 PAD 17083503284 PAD 17100136285 PAD 17085482286 PAD 17083515287 PAD 17087892288 PAD 17083000289 PAD 17083590290 PAD 17086474291 PAD 17083394292 PAD 17083588293 PAD 17125637294 PAD 17087922295 PAD 17125649296 PAD 18460100297 PAD 18460185298 PAD 18460173299 PAD 18460215300 PAD 17086796301 PAD TAPPING 17100094302 PAD TAPPING 17085032303 PAD TAPPING 17083450304 PAD TAPPING 17082730305 PAD TAPPING 17085421306 PAD TAPPING 17085081307 PAD TAPPING 17086152308 PAD TAPPING 17086693309 PAD TAPPING 17085457310 STRIP 17124591311 STRIP 17124669312 STRIP 17125273313 STRIP 17125285
314 STRIP 17125297315 STRIP 17125339316 STRIP 17125340317 STRIP 17125352318 STRIP 17125364319 STRIP 17129102320 ANGLE 17150541321 ANGLE 17150632322 ANGLE 17150693323 ANGLE 17082973324 ANGLE 17150670325 ANGLE 17150681326 ANGLE 17150905327 ANGLE 17129382328 ANGLE 17150474329 ANGLE 17150486330 ANGLE 17129588331 BRACKET 17083011332 CHANNEL 17082936333 ANGLE ASM 17060199334 ANGLE ASM 17043190335 ANGLE ASM 17043750336 CHANNEL ASM 17043281337 CHANNEL ASM 17050121338 PLATE ASM 17043293339 SHEET ASM 17980732340 FLASHING 17124773341 PAD 17085056342 Lamp Guard Asm 18360397343 Lamp Holder 18360385344 Lamp Receptacle 18350811345 Socket Asm 18350112346 Hand Lamp complete with lead 12365051347 Lamp Holder (Backelite) 12360016348 Dowel Pin 12431151349 Legend Plate 12373722350 Clamp 18520200351 Clamp 18520479352 Clamp Ins 18520224353 Clamp Ins 18520285354 Clamp Ins 18520595355 Clamp Ins 1 18520250356 Clamp Ins 1 1/2 18520571357 Clamp Ins 1/2 18520261358 Clamp Ins 1/2 18520297359 Clamp Ins 1/4 18520273360 Clamp Ins 3/8 18520522361 Clamp Ins 1-3/8 18520534362 Clamp Ins 1-1/8 18520509363 Clamp Ins 7/8 18520236364 INS. Clamp 18520443365 Conduit 18510218366 Conduit 18510048
367 Conduit 18510012368 Conduit 1- 1/2" 18510036369 Conduit 1/2" 18510190370 Conduit 2" 18510024371 Conduit APL 18510267372 Conduit Asm 18520637373 Conduit Asm 18520108374 Conduit Asm 18520110375 Conduit Asm 18520121376 Conduit Asm 18520133377 Conduit Asm 18520625378 Conduit Asm 18520662379 Conduit Asm 18520807380 Conduit Asm 18510231381 Conduit Asm 18510220382 Conduit Asm 18510243383 Bushing 17980045384 Bushing 1M Ins 18520686385 Bushing 2F Ins 18520352386 Bushing Ins 1-1/2 F 18520340387 Bushing Ins 1/2 F 18520327388 Bushing Ins 1/2 M 18520364389 Bushing Ins 2-1/2 F 18520674390 Insulated Bush Male 17161198391 Insulator CDT 1 18531234392 Insulator CDT 1/2 18531222393 Insulator Cond. 1-1/2 18531210394 Insulator Cond. 2-1/2 18510255395 Snap On 18540028396 Snap On 18540030397 Snap On 18540041398 Snap On 18540053399 Cleat 18460010400 Cleat 18460021401 Cleat 18460630402 Cleat 18460690403 Cleat 17271800404 Cleat 17271812405 Cleat 17271824406 Cleat 18460161407 Cleat 18460203408 Cleat 18460290409 Cleat 18460495410 Cleat 18460082411 Cleat 18460069412 Cleat 18460070413 Cleat 18460501414 Cleat 18460513415 Cleat 18460719416 Cleat 18460720417 Cleat 18460732418 Cleat 18460744419 Cleat 18460756
420 Cleat Rubber 18460033421 Block 18460793422 Block 18460781423 Block 18460770424 Block 18460768425 Bus Bar 18320491426 Bus Bar 18320016427 Bus Bar copper 14.9X1-1/2X1/2 18320041428 Bus Bar 11-3/4X1-1/2X1/2 18320405429 BOX CAB LIGHT 17121553430 BUSHING 18520844431 BUSHING 1/2 M STR RL 17980057432 BUSHING 1/2 M STR RL 17980070433 BUSHING INS 3/4 F 18520339434 CPLG 3/4 FCCM 18360452435 CPLG 31/2 FCCM 18360415436 ELBOW 1/2 FCCM 18520376437 ELBOW 1/2 FCCM FULL 18520716438 ELBOW 1/2 M STR RL 18520728439 FITTING 1-1/2 LB. 17281921440 FLEX CONDUIT 18510050441 INSULATOR 18530011442 STUD PLATE ASM 18460288443 STUD PLATE ASM 18480196444 Nipple 1/2 Short 18520017445 GRM PLN.328X0.7 18540016446 FITTING-1/2LL 17320562447 PAD TAPPING 17087272448 SEAL& WIRE 18330484449 SPACER CABLE 18460057450 CLAMP ASM 18520790451 CLAMP ASM 18520157452 CLAMP CABLE 18520078453 Insulated Clamp 17341255454 Lug Terminal E-Beam Cable as per EL/PT/0360. 12346639
455 Lug Terminal E-Beam Cable as per EL/PT/0360. 12346640
456 Lug Terminal E-Beam Cable as per EL/PT/0363. 12346718
457 Lug Terminal E-Beam Cable as per EL/PT/0365. 12346743
458 Lug Terminal E-Beam Cable as per EL/PT/0367. 12346780
459 Lug Terminal E-Beam Cable as per EL/PT/0368. 12346792
460 Lug Terminal E-Beam Cable as per EL/PT/0368. 12346809
461 Lug Terminal E-Beam Cable as per EL/PT/0368. 12346810
462 Lug Terminal E-Beam Cable as per EL/PT/0368. 12346688
463 Lug Terminal E-Beam Cable as per EL/PT/0376. 12346974
464 Lug Terminal E-Beam Cable as per EL/PT/0376. 12347061
465 Lug Terminal E-Beam Cable as per EL/PT/0376. 12346986
466 Lug Terminal 12340431
467 Lug Terminal 12346706
468 Wire Terminal E-Beam Cable as per EL/PT/0398. 12347073
469 Wire Terminal E-Beam Cable as per EL/PT/0398. 12347085
470 Wire Terminal E-Beam Cable as per EL/PT/0398. 12347097
471 Wire Terminal E-Beam Cable as per EL/PT/0398. 12347103
472 Wire Terminal E-Beam Cable as per EL/PT/0398. 12347115
473 Wire Terminal E-Beam Cable as per EL/PT/0398. 12347139
474 Wire Terminal E-Beam Cable as per EL/PT/0398. 12347140
475 Wire Terminal E-Beam Cable as per EL/PT/0398. 12347152
476 Wire Terminal E-Beam Cable as per EL/PT/0398. 12347190
477 Conduit Flexible Type 'B' 1" 12516016
478 Conduit Flexible Type 'B' 1-1/4" 12517010
479 Conduit Flexible Type 'B' 2" 12519017
480 Conduit Flexible Type 'B' 3/4" 12515012
481 Insulated Bush 1" Conduit 12528146
482 Insulated Bush 1-1/2" Conduit 12528080
483 Insulated Bush 1-1/2"BSP (Metalic) 12528171
484 Insulated Bush 1-1/4" Conduit 12528079
485 Insulated Bush 2" 12528110
486 Insulated Bush 2" BSP (Metalic) 12528109
487 Insulated Bush 2" Conduit 12528092
488 Insulated Bush 3/4" Conduit 12528134
489 Rubber Cleat 12461854
490 Rubber Cleat 12461878
491 Rubber Cleat 12461921
492 Rubber Cleat 12461805
493 Rubber Cleat 12461829
494 Rubber Cleat 12462068
495 Rubber Cleat 12462032
496 Grommet as per 3TPT-104. 12545818
497 Grommet as per 3TPT-104. 12545077
498 Grommet as per 3TPT-104. 12545065
499 Rigid Conduit 1" 42312887
500 Rigid Conduit 1-1/2" 42312929
501 Rigid Conduit 1-1/4" 42312905
502 Rigid Conduit 2" 42312930
503 Rigid Conduit 3/4" 42312875
504 Union Conduit 1-1/2" 12522053
505 Union Conduit 3/4" 12522065
506 Union Conduit 1-1/2" 12522089
507 Union Conduit 2" 12522028
508 Coupler 12524025
509 Coupler 1-1/2" 12524050
510 Coupler 2" 12524062
511 Coupling 1/2" BSP 12527014
512 Coupling 3/4" 12527038
513 Flexible Connector 12527210
514 Flexible Connector 12527221
515 Flexible Connector 2" 12527257
516 Flexible Connector 2"-90 Deg. 12527324
517 Assly Connection Cover & Bush Cover Cable 12479652
518 Copper Strip 1-1/2" x 1/4" 91104762
519 Lug Terminal E-Beam Cable as per EL/PT/0364. 12346720
520 Lug Terminal E-Beam Cable as per EL/PT/0376. 12347024
521 Cable Grip 12529310
522 Chain Cleat 12461866
523 Hose Clip Warm Drive 12529205
524 PVC Sleeving 12531030
525 Connection Box Complete 12523483
526 Connection Box Complete 12523495
527 Extension Ring Box 12523010
528 Ferrule 1/4" 12470030
529 Inspection Elbow 1" 12520044
530 Inspection Tee 1" 12520093
531 Inspection Tee 1-1/4" 12520100
532 Insulate Chase Nipple 12526150
533 Insulated Chase Nipple 12526022
534 Nipple 3/4"x1" Close 12526058
535 Nipple 3/4"x2" Short 12526060
536 Nipple 3/4"x2-1/2" Short 12526071
537 P.C.F.Conduit & Fittings Kit 1" 12520550
538 P.C.F.Conduit & Fittings Kit 1-1/2" 12520561
539 P.C.F.Conduit & Fittings Kit 3/4" 12520548
540 Reducer 1"x3/4" 12524554
541 Reducer 1-1/2"x1" 12524566
542 Reducer 1-1/4"x1" 12524530
543 C.B. Guard ( 6 Points) 12478982
544 Cable Marker 12375019
545 Cable Marker 12375020
546 Guard Battery Switch 12470016
547 PVC Tape (Adhesive) 3/4" 12530025
548 PVC Tape (Non Adhesive) 3/4" 12530013
549 Air Sealing Ring Sch. No. 00223 12431140
550 Conduit Fitting Kit (Flexible Connector coupling etc) 12520597
551 Connector Flexible Straight 1-1/4” 12527233
552 Conduit Fitting Kit (Malleable C.I.) 12520615
553 Conduit Fitting Kit (Ins. End Bush, Spacer etc) 12520603
554 Cable Cleat Kit 12520585
555 Conduit Fitting Kit (Cap Clamp, Base Clamp etc) 12520573
556 Conduit Fitting Kit (Nipple, Reducer, Coupler etc) 12520627
557 Screwed Reducer 12524529
558 Outlet Box with cover 12523057
559 Metal Clad SocketDrg. No. DEL/MISC/32 12360685
560 Base Calamp Cond.Drg.No. DEL-MISC/40 12529291