door manual - revit-content.com · frame depth position from interior frame depth position from...

Revit Content®

Copyright 2009 -2010 by Content & More Limited, All Rights reserved

RFA - 2116Door

DOOR MANUAL

Revit Content®


RFA - 2116Door

of 18

FRAMEREBATES

FRAMETYPES

DOOR FLUSH SYMBOL LINES

WOOD FRAME METAL FRAME

SIDE LIGHTS &TRANSOM

PANEL GLAZING

DOUBLE PANEL DOOR ACCESSORIES

DOOR TYPES VOID FOR ADDITIONALWALL

DOOR

FEATURES

OVERVIEW

Height

Width

Side Light Sill Bottom Height Offset

Side Light Sill Bottom Height Offset

Side Light Right WidthSide Light Left Width

Transom Height

Rough Distance RightRough Distance Left

Rough Distance Left Rough Distance Right

Side Light & Transom Frame Width Side Light & Transom Frame Width

Door Handle Height Position

Width Side Light Right WidthSide Light Left Width

Side Light & Transom Frame Width

Rough Distance Left Rough Distance Right

Side Light Glazing Thickness

Door Opening Left & Single

Door Opening Right

Revit Content®


RFA - 2116Door

ELEVATION DIMENSIONS SIDE LIGHTS, TRANSOM& DOUBLE DOORS

of 18

DIMENSIONS OVERVIEW

PLAN DIMENSIONS SIDE LIGHT & DOUBLE DOORS

Swing Panel Radius Middle Side Top

Swing Panel Radius H

inge Side Top

Swing Panel Radius Hinge Side Bottom Sw

ing Panel Radius Middle Sid

e Bottom

Fix Panel Radius Middle Side Top

Fix Panel Radius Middle Side Bottom

Fix Panel Radius H

inge Side Bottom

Fix Panel Radius Hinge Side Top

Sliding Door Position From Interior

Sliding Door Space Sides

Sliding Swing Panel Offset Sliding Fix Panel Offset

Sliding Door Space Sides

Door Glass Position From Exterior

Door Glass Thickness

Frame Depth Position From Interior

Frame Depth Position From Exterior

Revit Content®


RFA - 2116Door

ELEVATION DIMENSIONS SLIDING DOORS &OPENING

of 18

DIMENSIONS OVERVIEW

PLAN DIMENSIONS SLIDING DOORS

Taper Reveal Interior RightTaper Reveal Interior Left

Height

Width

Door Handle Height Position

Door Handle Position From Sides

Rough Distance Left

Taper Reveal Interior Left

Taper Reveal Exterior Left

Taper Reveal Interior Right

Taper Reveal Exterior Right

Revit Content®


RFA - 2116Door

ELEVATION DIMENSIONS TAPERED REVEALS

DIMENSIONS OVERVIEW

of 18

PLAN DIMENSIONS TAPERED REVEALS

Width Swing

Height

Swing Panel Frame Bottom Thickness

Swing Panel Frame Top Thickness

Swing Panel Frame Hinge Side Thickness Swing Panel Frame Middle Side Thickness

Fix Panel Frame Bottom Thickness

Fix Panel Frame Middle Side Thickness

Fix Panel Frame Hinge Side Thickness

Fix Panel Frame Top Thickness

Width

Kickplate Height

Width Swing

Width

Revit Content®


RFA - 2116Door

ELEVATION DIMENSIONS DOUBLE DOORS &GLAZING OPENING

DIMENSIONS OVERVIEW

of 18

PLAN DIMENSIONS DOUBLE DOORS

Frame Depth Position From Interior

Frame Depth Position From Exterior

Rough Distance Left

Hinge Radius

Hinge Offset

Frame Metal Shell Thickness

Frame Metal Fold Depth Interior

Frame Metal Fold Depth Exterior

Frame Width Interior

Frame Width Exterior

Frame Rebate Width 2

Framel Rebate Width 1

Frame Rebate Depth 1

Frame Groove Width

Frame Groove Depth

Space 2

Space

Frame Metal Rebate 1 Width

Frame Metal Rebate 2 Width

Frame Rebate Depth 2


Frame Depth 3

Frame Groove Width

Frame Groove Depth

Frame Metal Shell Thickness

Rough Distance Left

Hinge OffsetH

inge Radius

Door Panel Frame Offset

Frame Depth Position Interior

Render Offset Sides Exterior

Render Offset Sides Interior

Revit Content®


RFA - 2116Door

PLAN DETAIL Of METAL FRAME TYPE 1

PLAN DETAIL Of METAL FRAME TYPE 3

DIMENSIONS OVERVIEW

of 18

Frame Wood Middle Width


Frame Width Exterior

Rough Distance Left


Frame Depth Position Exterior

Frame Wood Interior Side Offset

Frame Wood Exterior Side Offset

Frame Wood Depth Interior & Exterior

Frame Wood Depth Interior & Exterior

Space 2

Space


Frame Depth 3

SpaceSpace 2

Hinge Offset

Frame Wood Middle Width

Rough Distance Left

Revit Content®


RFA - 2116Door

DIMENSIONS OVERVIEW

PLAN DETAIL Of WOOD FRAME TYPE 1

PLAN DETAIL Of WOOD FRAME TYPE 3

of 18

Door Handle 2 Length

Door Handle 2 Depth 2

Door Handle 2 Width

Door Handle 2 Depth

Door Handle 1 Radius

Door Thickness

Door Handle Position From Sides

Space

Door Handle 1 Depth

Door Lock Length

Door Lock Width

Door Lock Radius

Door Handle1 Radius

Door Handle1 Width

Door Handle1 Length

Door Handle Length

Revit Content®


RFA - 2116Door

PLAN DETAIL OF HANDLE

DIMENSIONS OVERVIEW

of 18

ELEVATION DOOR ACCESSORIES

Revit Content®


RFA - 2116Door

Section 1 Closure Frame Section 2 Block Frame Section 3 Corner Frame

SECTION OVERVIEW

of 18

Frame Type 1 Frame Type 2 Frame Type 3

Revit Content®


RFA - 2116Door

How To Create Double & Single Doors

In the Type Parameters under:-

GraphicsThe tick box that needs to be selected is:-DOUBLE DOOR

If the Tick Box DOUBLE DOOR is selected,The Result is shown as a Double Swing Door as shown in Fig 1If unselected, The Result is shown as a Single Swing Door as shown in Fig 1

DimensionsYou can specify and control the panel width with the Parameters WIDTH SWING.This parameter lets you control the width of the Left panel when DOUBLE DOOR is selected,When the width of the left panel is adjusted the right panel changes its width accordingly.You can adjust the WIDTH SWING so that you have a result of the left panel to have an equal or greaterwidth to the right panel.

Please Note when adjusting the WIDTH of the panel when double doors, the WIDTH SWINGhas to be adjusted accordingly as the value you put in for this parameter stays fix and the right paneladjusts to the remaining width of the clear WIDTH opening. The WIDTH SWING value needs to be morethan 300mm.

The single door is adjusted by the parameter WIDTH and adjusts automatically to the width of theopening and the right door dissapears

If DOUBLE DOOR is unselected which results in a single swing panel than the parameterWIDTH SWING does not need to be adjusted.

(PLEASE REFER TO DIMENSIONS OVERVIEW )

How To Create Single & Double Sliding Doors

The parameters DOOR OPENING LEFT & SINGLE is for the left door as shown inDimensions overview page 2 of 15When you untick DOUBLE DOOR the result is a Left single swing door which theparameter DOOR OPENING LEFT & SINGLE is used for.

To create a Right single swing door,there is a flip control switch as shown In plan. Thiswill flip the Door to give a result of a Right single swing door which the same parameteris used to open and close the swing door.

The parameters DOOR OPENING RIGHT is for the Right door. When you tick DOUBLEDOOR the result is a Right swing door which the parameter DOOR OPENING RIGHT isused for

Please note that these parameters are not angle parameters but are integer percentageparameters.


GraphicsThe tick box that needs to be selected is:-SLIDING DOOR

If the Tick Box SLIDING DOOR & DOUBLE DOORis selected,the Result is shown as a Double Sliding Door as shown in Fig 2If DOUBLE DOOR unselected, the result is shown as a Single Sliding Door as shown in Fig 2

DimensionsThe Additional parameters that you can control for the sliding doors are:-SLIDING SWING PANEL OFFSET & SLIDING FIX PANEL OFFSETThese parameters let you control the amount of offset you require for the door to be within the cavity left& right. If the parameter is adjusted to zero, the door will be the same size as the opening width. If youadjust this parameter to 50mm, the door will have an offset of 50mm in to the cavity.SLIDING DOOR SPACE SIDESThis parameter lets you control the space between the Door Panel and the Cavity. Adjusting this parameterto zero will result with no space, if adjusted to 5mm there willl be a space of 5mm between the panel andthe cavity.SLIDING DOOR POSITION FROM INTERIORThis parameter lets you control the position of the door from the interior.You can create a door which is either on the internal surface of the wall just by adjusting this parameter tozero or have an offset to have the sliding doors center of the wall.Please refer to page 4 of 15 Plan View By adjusting the parameter FRAME DEPTH POSITION FROM INTERIORyou can create the position of the sliding door to flush with the interior of the wall or have the position onthe external surface of the wall.

Please note that the parameter WIDTH SWING adjust when Sliding Door & Double Door is activated


How To Create Transom Window & Side LightsIn the Type Parameters under:-

GraphicsThe tick boxes that need to be selected are:-SIDE LIGHT LEFT VISIBILITY,SIDE LIGHT RIGHT VISIBILITY & TRANSOM WINDOW VISIBILITY

If the Tick Box SIDE LIGHT LEFT VISIBILITY,SIDE LIGHT RIGHT VISIBILITY &TRANSOM WINDOW VISIBILITY are selected,The Result is shown as Fig 3If unselected, The Result is shown without any Sidelight or Transom.

DimensionsThe Additional parameters that you can control for the Side Lights and Transom Window are:-SIDE LIGHT & TRANSOM INTIGRATEDIf selected, this Parameter allows you to have a Side Light which has a separate frame from the door to aintigrated frame to the door.SIDE LIGHT SILL VISIBILITYThis parameter lets you control the visibility of the internal & external sill.The parameters for these sills are explained belowSIDE LIGHT SILL BOTTOM HEIGHT OFFSETThis parameter lets you control the height of the Side Light Sills

SIDE LIGHT & TRANSOM FRAME WIDTHSIDE LIGHT LEFT WIDTH, SIDE LIGHT RIGHT WIDTH & TRANSOM HEIGHTSIDE LIGHT EXTERNAL SILL PLATE HEIGHTSIDE LIGHT EXTERNAL SILL DEPTHSIDE LIGHT EXTERNAL SILL ANGLESIDE LIGHT INTERNAL SILL HEIGHTSIDE LIGHT INTERNAL SILL DEPTH


of 18

FIG 1

FIG 2

FIG 3

Openings

Revit Content®


RFA - 2116Door

How To Create Frame Types & Frame Rebates


ConstraintsTo change the Frame Type or Frame Rebate the parameters are:-FRAME TYPE & FRAME REBATE

The FRAME TYPE has 3 Types as shown in Fig 4

Frame Type 1= Closure FrameFrame Type 2= Corner FrameFrame Type 3= Block Frame

Frame Type 1 which is a Closure Frame, closes the depth of the wall or can be flushwith the wall on the interior and exterior. The Parameter which controls the positions are:-FRAME DEPTH POSITION INTERIOR & FRAME DEPTH POSITION EXTERIOR Please refer topage 4 of 15 Plan View. By adjusting the parameter FRAME DEPTH POSITION FROM INTERIOR. Youcan have a negative value which results in the frame adjusting outwards, or have a zero value to havethe frame flush with the walls, or have a possitive value which results the frame adjusting inwards.

Frame Type 2 which is a Corner Frame sits on the Interior corner of the wall

Frame Type 3 which is a Block Frame sits anywhere in the middle of the wall. The Parameter whichcontrols the position of the Block Frame is FRAME DEPTH POSITION INTERIOR

The FRAME REBATE can hace up to 2 Rebates as shown in Fig 5

Frame Rebate 0 = No RebateFrame Rebate 1= One RebateFrame Rebate 2 = Two Rebates

The Frame Rebates can be used along with all frame types appart from the Sliding Doors whichautomatically adjust to Frame Type 1 and the Side Lights setups and Transom window automaticallyadjust to Frame Type 3.

These Frame Types can be adjusted to either Wood Frame or Metal with a click of a buttonenabling WOOD FRAMEAll parameters for frame types, frame rebates and positioning have the same parameters for bothWood frame & Metal frames


How To Create Tapered Reveals & Render OffsetsIn the Type Parameters under:-

DimensionsTo Have Tapered Reveals the parameters are:-TAPER REVEAL INTERIOR LEFT,TAPER REVEAL INTERIOR RIGHT,TAPER REVEAL EXTERIOR LEFT,TAPER REVEAL EXTERIOR RIGHT,TAPER REVEAL INTERIOR TOP,TAPER REVEAL EXTERIOR TOP.

All parameters can be adjusted sepparatly as shown in Fig 7

To Have Render Offset the parameters are:-RENDER OFFSET SIDES INTERIOR, RENDER OFFSET SIDES EXTERIOR,RENDER OFFSET TOP INTERIOR, RENDER OFFSET TOP EXTERIOR.as shown in Fig 8

Please note that the positioning of the frame will affect the reveals adjusting

These parameters also can be used on a joined wall Please refer to page13 of 15 Fig 12 and notes


HingesThe Hinge Position automatically dissapear when Sliding Door is activated.When DOOR FLUSH is selected the Hinge Position is automatically adjusted to the center of thespace between the door and the Frame as shown in Fig 10.When Door Flush is deactivated the Hinge Position repositions itself to the the side of the panelwhich offsets from the frame and center as shown in Fig 9. The panel offset can be adjusted byusing the parameter PANEL FRAME OFFSET only when the parameterDOOR FLUSH is not selected .These parameters can be adjusted in any Door setup


DimensionsTo Adjust Hinges the parameters are:-HINGE RADIUS , HINGE OFFSET


Rough Distance


DimensionsTo Have a Rough Distance from the Clear Width the parameters are:-ROUGH DISTANCE LEFT, ROUGH DISTANCE RIGHT,ROUGH DISTANCE TOP , ROUGH DISTANCE BOTTOM ,ROUGH DISTANCE BOTTOM INSTANCEAll These parameters can be adjusted sepparatly as shown in Fig 6

Rough distance on each side is from the clear opening Width or Height as Shown in Dimensions overviewpage 2 of 15This has to be manually adjusted. if you have a situation where you cannot see the frame, this is probablybecause the Rough Distance is set to zero. If you do not want the frame visible, there is a paramater which iscalled FRAME VISIBILTY. Unselect this tick box and adjust the Rough Distance on all sides to be 0 or adesired valueROUGH DISTANCE BOTTOM is type related parameter for all types. ROUGH DISTANCE BOTTOM INSTANCE isrelated to one instance. Both Parameters have the same function. To extend the Bottom opening of the doorfor variating floor thicknesses you can adjust either parameters for one instance or all types.


Door Flush & not FlushGraphicsWhen DOOR FLUSH is Selected as shown in Fig 10

When DOOR FLUSH is Deselected as shown in Fig 9


of 18

FIG 4

FIG 5

FIG 6

FIG 7

FIG 8

FIG 9

FIG 10

Frame Type

Frame Rebate

1 2 3

0 1 2

0 1 2

Revit Content®


RFA - 2116Door

How To Create Panel Glazing


GraphicsTo Create Panel Glazing, The parameters are:-PANEL GLAZING VISIBILITY LEFT , PANEL GLAZING VISIBILITY RIGHTWhen both Parameters are selected the result is shown as Fig 11

DimensionsEach door has its own parameters to adjust the Panel Glazing frame thickness andthe radius for each corner of the panel frameThe Parameters for the Left Door are:-

SWING PANEL FRAME BOTTOM THICKNESS, SWING PANEL HINGE SIDE THICKNESS,SWING PANEL MIDDLE SIDE THICKNESS, SWING PANEL TOP THICKNESSSWING PANEL RADIUS HINGE SIDE TOP, SWING PANEL RADIUS HINGE SIDE BOTTOM,SWING PANEL RADIUS MIDDLE SIDE TOP , SWING PANEL RADIUS MIDDLE SIDE BOTTOM

The Parameters for the Right Door are:-

FIX PANEL FRAME BOTTOM THICKNESS, FIX PANEL HINGE SIDE THICKNESS,FIX PANEL MIDDLE SIDE THICKNESS, FIX PANEL TOP THICKNESSFIX PANEL RADIUS HINGE SIDE TOP, FIX PANEL RADIUS HINGE SIDE BOTTOM,FIX PANEL RADIUS MIDDLE SIDE TOP & FIX PANEL RADIUS MIDDLE SIDE BOTTOM

To Create a door which is a fully glazed door without frames. switch off the parametersPANEL GLAZING VISIBILITY LEFT & PANEL GLAZING VISIBILITY RIGHT and set the door thicknessto atleast 12mm & change the matirial from Wood to Glass as shown as Fig 11


How To Create Double Panel


GraphicsYou can setup a Double Panel Door for the Single and Double Swing Door asyou might need for Hotel or Office Project where noise reduction is a subject.ToCreate Double Panel,The parameters are:-DOUBLE PANEL VISIBILITY as shown as Fig 13


How To Create Symbol Lines


Constraints

To Create Symbol Lines select the parameters in the instance properties boxSYMBOL LINES the result will beFig 14 & 15

All Symbol Lines will appear in Plan & Elevations

To have symbol lines adjusted to your local standards, showing the opposite sidein elevation, adjust the parameterSYMBOL LINES FROM HINGE SIDE the result will show the symbol lines fliped only in elevation on theopposite side as shown in Fig 15

To Have Symbol Lines adjusting in plan view, select the parameterSYMBOL LINES OPENING ANGLE SYNC.The symbol lines will adjust with the Parameters:-DOOR OPENING LEFT & SINGLE and DOOR OPENING RIGHT

If the parameter SYMBOL LINES OPENING ANGLE SYNC is unselected, the symbol lineswill not adjust with the parametersDOOR OPENING LEFT & SINGLE and DOOR OPENING RIGHT.They can be manually adjusted with the parameters under the Dimensions calledSYMBOL LINES OPENING ANGLE RIGHT & SYMBOL LINES OPENING ANGLE LEFT.The Symbol lines will remain static at the postion you require once adjusting, while you adjust thedoors to a close position or a angle that you specify as shown in Fig 13

Please note that these symbol lines are shown in Coure, Medium & Fine Modes and are ideally usedin plan view with or without the Doors Visibility.

To switch off the Doors Visibility , under Graphics unselect the parameterDOORS VISIBILTY.All doors for that type will be switched of and you will remain with the symbol lines showing.To switch of the symbol lines simply unselect the SYMBOL LINES parameter under Graphics, allSymbol lines will turn off.

Void For Additional Walls


DimensionsIf you need to add an additional Wall (e.g. Dry-Lining) to join with the original wall. Create a newbasic wall, change the properties as your specification and join the to origional wall.To cut the new additional wall that has been added either to the interior or exterior of theorigional wall, adjust the parameters:-

VOID INTERIOR OFFSET or VOID EXTERIOR OFFSET to the thickness of the additional new walladded, the result will be a cut out of the new wall as shown in Fig 12

Please note that all parameters for tapered reveals and render offset can apply to newadditional walls when the void is offseted


of 18

FIG 11

FIG 12

FIG 13

FIG 14

FIG 15

Revit Content®


RFA - 2116Door

Door Accessories

In the Instance Parameters under:-

Constraints INTERIOR LEFT SWING 1 ACCESSORIES, INTERIOR LEFT SWING 2 ACCESSORIES, INTERIOR RIGHT FIX 1 ACCESSORIES, INTERIOR RIGHT FIX 2 ACCESSORIES EXTERIOR LEFT SWING 1 ACCESSORIES, EXTERIOR LEFT SWING 2 ACCESSORIES, EXTERIOR RIGHT FIX 1 ACCESSORIES, EXTERIOR RIGHT FIX 2 ACCESSORIES

Each Integer parameter has the same visibility configuration on each sides of the door panels. When adjusting the integer parameter from 0 - 10 the results are the following:-


1 2 3 4 5

6 7

8 9

Door Lever Handle Door Knob Handle Door Lever Handle withDoor Knob Handle

Lock Door Lever Handle,DoorKnob Handle & Lock

Kickplate Door Lever Handle &Kickplate

Door Knob Handle,Lock & Kickplate

Door Lever Handle with KnobHandle, Lock & Kickplate

of 18


DimensionsAll The accessories haveDimensions and are stated asbelow

Door Knob HandleDoor Handle 1 LengthDoor Handle 1 WidthDoor Handle 1 DepthDoor Handle 1 Radius

Door Lever HandleDoor Handle 2 WidthDoor Handle 2 DepthDoor Handle 2 Depth 2Door Handle 2 RadiusDoor Handle 2 AngleDoor Handle 2 Height Postion

Door LockDoor Lock LengthDoor Lock WidthDoor Lock DepthDoor LockRadiusDoor Lock Height Position

Kick PlateKickplate Side OffsetKickplate HeightKickplate ThicknessKickplate Bottom Offset

Door Handle Height PositionDoor Handle Position From Sides

(PLEASE REFER TO DIMENSIONSOVERVIEW )

INTERIOR LEFTSWING 1ACCESSORIES

INTERIORRIGHT FIX 1ACCESSORIES

INTERIOR LEFTSWING 2ACCESSORIES

INTERIOR RIGHTFIX 2ACCESSORIES

EXTERIOR LEFTSWING 2ACCESSORIES

EXTERIOR RIGHTFIX 2ACCESSORIES

EXTERIOR LEFTSWING 1ACCESSORIES

EXTERIOR RIGHTFIX 1ACCESSORIES

Threshold Middle Depth

Threshold Offset From Interior

Threshold Exterior Depth

Threshold Height

Clear Opening

Clear Opening

Rough Opening

Rough Opening

Pivot Offset Y Position

Pivot Offset X Position

Revit Content®


RFA - 2116Door

Frame Fold Interior & Frame Fold Exterior


GraphicsTo Create Frame Folds, The parameters are:-FRAME FOLD INTERIOR & FRAME FOLD EXTERIOR

Each Integer parameter has the same visibility configuration on each sides.When adjusting the integer parameter from 0 - 2 the results are the following:-

Metal Frame as shown in Fig 16FRAME FOLD INTERIOR0 = No Fold1 = Fold2 = Shadow Gap

FRAME FOLD EXTERIOR0 = No Fold1 = Fold2 = Shadow Gap

Wood Frame as shown in Fig 17FRAME FOLD INTERIOR0 = No Fold1= Interior Architrave

FRAME FOLD EXTERIOR0 = No Fold1= Exterior Architrave


FIG 16

Interior

Exterior

Interior

Exterior1

1

1

1 2

1

2

FIG 17

Threshold


GraphicsTo Adjust a Threshold, The parameter is:-THRESHOLD

When adjusting the integer parameter from 0 - 4 the results are the following:-

THRESHHOLD0 = No Threshold1 = Interior & Middle Thresholds2 = Exterior & Middle Thresholds3 = Middle Threshold4 = Interior Middle & Exterior Thresholds

DimensionsThreshold Middle Height OffsetThreshold Middle DepthThreshold Exterior DepthThreshold Interior DepthThreshold Height


FIG 18

FIG 19

Clear Opening


GraphicsTo Adjust the opening, The parameter is:-CLEAR OPENING

If Seleceted The Parameter Height & Width represents the Clear OpeningIf Unselected The Parameter Height & Width represents the Rough Opening

When selecting the parameter CLEAR OPENING , the results is:-The Clear opening of the Height & Width of the door as shown inFig 20 & Fig 21When unselecting the parameter CLEAR OPENINGThe result is Rough Opening of the Height & Width as shown inFig 20 & Fig 21

Please note that the dimension line in plan view which has the option ofshowing the height as well as the width, represents the value of the heightwhen the parameter is selected and unselected to show the result of the ClearHeight & Width or the Rough Opening Height & Width


FIG 20

FIG 21

Pivot Position Offset


GraphicsTo Adjust the opening, The parameter is:-PIVOT POSITION OFFSET

When selecting the parameter PIVOT POSITION OFFSET, the results isshown in Fig 20

DimensionsPivot Offset X PositionPivot Offset Y Position


of 18

Revit Content®


RFA - 2116Door

REVISION 5

Our new Revised family now has the advanced option to have a Groove or No Groove as Well as Double Rebate. These options can beadjusted with selecting the parameter "GROOVE" or "DOUBLE REBATE"The "DOUBLE REBATE" is only activated when the Metal frame is activated and Frame Type 1 is selected as shownn in FIG 22 & 23

We have also included now a Door Stop for the Wood frame. This is also controled by selecting the Parameter "DOOR STOP"This is only activates when the Wood frame is activated and Frame Type 1 is selected as shownn in FIG 22

As well as these option we have now introduced a Metal Anchor which as shownn in FIG 23 the can be controled by a length parametercalled Metal Anchor Length. When yero the visibility will swictch off

FIG 22

FIG 23

FIG 22

GROOVE NO GROOVE

DOOR STOP

DOUBLEREBATE

DOUBLEREBATE

DOUBLEREBATE

METAL ANCHOR SHADOW GAP INTERIORFRAME FOLD INTERIORREBATE 0

of 18

Revit Content®


RFA - 2116Door

REVISION 5

3D SYBOL LINES

Our new Revised family now has the advanced option to have 3D Symbol Lines as well as 2D Symbol Lines. These options can be adjusted withselecting the parameter "2D SYMBOL LINES" or "3D SYMBOL LINES" under the Graphics Menu

The 2D SYMBOL LINES Can only be viewed in Plan & Elevation, the 3D SYMBOL LINES Show in all views

of 18

Revit Content®


RFA - 2116Door

MIDDLE RAIL

MIDDLE RAIL 2

REVISION 5

Our new Revised family now has the advanced option to have a middle rail which can be setup to diffrent configurations as shownabove. These options can be adjusted with selecting the parameter "MIDDLE RAIL" under the Graphics Menu

The Middle Rail has 3 Parameters which can be adjusted to have the configuration that you need. These parameters are called:"MIDDLE RAIL HEIGHT", "MIDDLE RAIL SIDE OFFSET" & "MIDDLE RAIL HEIGHT POSITION"

Please note that the position of the Middle Rail is offseted from the Door Panel Frame

of 18

door manual - revit-content.com · frame depth position from interior frame depth position from...

Documents