.
BOLT SEQUENCELoosening – start with #25
Tightening – start with #1
Numbered bolts are 8mm, others are 10mm
Guide Pin Bolt 10mm
Guide Pin Bolt 10mm
All bolts torqued 90-120 in/lbs
Rooster Comb Spring
Shift linkage shaft
Manual Valve
Shaft tab fits into manual valve groove
Picture is 95 model
Parking Pawl
MLPS
Shift linkage shaft
Shift linkage arm
Outer line on MLPS must line up with
inner line with shifter in Neutral
Picture is 95 model
MLPS attachment
bolts (2)
Manual Valve
Shaft tab fits into manual valve groove
EPC Solenoid
Picture is 95 model
Shift Tab
EPC Solenoid
Shift Solenoid Pack
TCC Solenoid
Linkage Pin Round Screen
1-2 Piston
Reverse Servo
2-3 Piston
2-3 Piston
OD Servo
Reverse Servo
1-2 Piston
Picture is 95 model
Round Screen (earlier models)
Linkage Pin
Larger screen here on later models
Access OD Band here
Debris can get trapped inside
valve body
SquareScreen
Manual Valve
Check Balls (8)
Round check valve
End plug with threaded hole
Picture is 95 model
Reinforcement Plates – note orientation
Earlier models only
Extra bolt
Separator Plate
Manual Valve
Note sequence of parts for each valve
Note sequence of parts for each valve
This one has 2 valves and 2
clips
Must be spotless!
Note sequence of parts for each valve
EPC Solenoid
Picture is 95 model
Shift linkage
Shift linkage retaining nut is partially visible here
Picture is 95 model
Parking pawl
“Rooster comb”
Linkage shaft
OD band
2.7” OD servo
Stock OD servo return springAnchor bracket (ea
end)
Center bolt with nut tack-welded to other side of
bracket
Valve Body Bolts
OD ServoOD servo
removal bracket
Drum
OD Band
Fixed Anchor
OD servo
tighten
loosen
Band out of Position
No contact
Drum
OD Band
Fixed Anchor
OD servo
tighten
loosen
Correct Band Position
Contact
Drum
OD Band
Fixed Anchor
Maintaining Band Position
Use screwdriver or similar to
push/keep band into proper
position while servo is removed
push
Separator plate top gasket
Picture is 95 model
Filter
Wire Harness
TCC Solenoid
Shift Solenoids
EPC Solenoid
Temp Sensor
Picture is 95 model
Valve Body
Filter (note extension for later model deeper pan)
TCC Solenoid
Shift Solenoids
Plastic Harness
Picture is 02 model
Manual Valve
Transmission filer o-ring needs to be
removed
TCC Solenoid
Shift Solenoids
Shift linkage fits into manual valve
Picture is 02 model
Plastic harness
Plastic harness
Valve body bolt retains shift solenoid bracket
Shift Solenoids
Picture is 02 model
Use small screwdriver to gently pry out retaining tabs on harness
Picture is 02 model
Plastic harness
Sonnax upgrade parts
Picture is 02 model
Picture is 02 model
Sonnax 76948-09 upgrade
Pressure regulator valve
Picture is 02 model
Sonnax 76948-29K upgrade
OD servo regulator valve & sleeve
Picture is 02 model
TCC Solenoid
Shift Solenoids8mm valve body bolt retains shift solenoid bracket
Valve body cover plate
10mm bolt retains both
brackets
Manual valve
Picture is 02 model
OD Servo
OD band can be seen here – this is where flat
blade object can be used to push against band to retain it when OD servo is removed
Picture is 02 model
Flat blade bar pushed against
OD band to retain it while OD servo is
removed
OD servo removal bracket
OD servo
OD Servo
Stock (stiffer) OD return
springHi-perf (softer) OD
return spring
Picture is 02 model
Screen fits up into case here before valve
body is installed
1-2 piston/accumulator cover
Molded Rubber OEM gasket
Deeper (later model) pan
Magnet