![Page 1: 011-0131-01 rev A SPEED SENSOR II USERS MANUAL](https://reader030.vdocument.in/reader030/viewer/2022012717/61af6ddfbe9c012dde7c05cd/html5/thumbnails/1.jpg)
Applied Concepts, Inc. 2609 Technology Drive Plano, Texas 75074 972-398-3780
Stalker Speed Sensor II User’s Manual 011-0131-01 rev. A
![Page 2: 011-0131-01 rev A SPEED SENSOR II USERS MANUAL](https://reader030.vdocument.in/reader030/viewer/2022012717/61af6ddfbe9c012dde7c05cd/html5/thumbnails/2.jpg)
Speed Sensor II User’s Manual
2
Regulatory Statement
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their expense.
Changes or modifications not expressly approved by Applied Concepts, Inc. could void the user's authority to operate the equipment.
Not intended or approved for Law Enforcement use in the United States.
Stalker/Applied Concepts
2609 Technology Drive Plano, TX 75074 USA
1-800-STALKER
(972) 398-3750 Sales / (972) 398-3751 Fax
www.stalkerradar.com
![Page 3: 011-0131-01 rev A SPEED SENSOR II USERS MANUAL](https://reader030.vdocument.in/reader030/viewer/2022012717/61af6ddfbe9c012dde7c05cd/html5/thumbnails/3.jpg)
Speed Sensor II User’s Manual
3
TableofContents1 Introduction .......................................................................................................................................... 4
2 Connecting the Speed Sensor to the PC ............................................................................................... 4
3 PC Application ....................................................................................................................................... 5
3.1 LoadingtheDeveloper’sKitCD .................................................................................................. 5
3.2 PollingforSpeedSensorID ........................................................................................................ 5
3.3 TroubleshootingCommunicationIssues ................................................................................... 6
4 Configuring the Speed Sensor ............................................................................................................... 7
4.1 ReadingtheCurrentConfiguration ............................................................................................ 9
4.2 ChangingandSavingtheConfiguration ................................................................................... 10
4.3 ConfigurationSettings............................................................................................................... 12
4.4 ChangingtheBaudRate ............................................................................................................ 12
4.5 DefaultSettings .......................................................................................................................... 12
4.5.1 FactoryDefaults ................................................................................................................. 12
4.5.2 ConfigurationFileDefaults ............................................................................................... 13
4.6 PrintingSettingValues .............................................................................................................. 14
4.7 DemoApplicationSoftKeys ..................................................................................................... 14
4.8 Fork Test ...................................................................................................................................... 15
4.9 MonitoringSpeedData ............................................................................................................. 16
4.10 LoggingSpeedData ................................................................................................................... 18
5 Configuring the Stalker Dashboard Application .................................................................................. 19
5.1 ApplicationControlFile ............................................................................................................ 20
5.2 Speed Sensor Configuration File ................................................................................................. 21
5.3 Softwareupdates ....................................................................................................................... 24
6 FCC Requirements ............................................................................................................................... 26
![Page 4: 011-0131-01 rev A SPEED SENSOR II USERS MANUAL](https://reader030.vdocument.in/reader030/viewer/2022012717/61af6ddfbe9c012dde7c05cd/html5/thumbnails/4.jpg)
Speed Sensor II User’s Manual
4
1 IntroductionAppliedConceptsprovidesaSensorstartupkitthatincludescablesandPCsoftwarethatcanbeusedtoquicklyconnectasensoruptoaPCfortestingandconfiguringthesensor.Thesenorhasmanyconfigurationsettingthatcanbealteredbytheusertooptimizethesensorperformancefortheirparticularapplication.Forthedetailsontheconfigurationregisters,thereuseandtheirsettingrefertotheSpeedSensorIITechnicalGuide.
2 ConnectingtheSpeedSensortothePCBeforeconnectingthesensortothePCbesuretocheckwhichtypeofconnectionyouwanttomake.ThesensorscanbeconnectedusingeitheraRS‐232portorRS‐485port.Thedeveloper’skitwillshipwithacableforoneortheotherdependingonwhichkittheuserordered.IfthekitbeingusedistheRS‐232versionitcanbeconnecteddirectlytoaPC.IfthePCdoesnothavea9pinserialportconnectortheyyouwillneedtouseaUSBtoserialconvertorwhichareavailableatmoststoressellingcomputersupplies.Steps:
ConnectthePower/DatacabletotheSpeedSensor. ConnecttheRS‐485toRS‐232convertertotheDB9connectorifitisaRS‐485cable. ConnecttothePCusingtheprovidedserialcable.Thisisa“straight‐through”serial
cable.(Donotreplaceitwitha“nullmodem”cablewhichwillswapthetransmitandreceivewires).
ConnecttopowerbypluggingthepoweradapterintotheAClineandthenplugthepowerconnectorintothePower/Datacable.IfusingtheDCpowercable,thenplugthecigaretteplugintoa12VDC(nominal)powersupply.
![Page 5: 011-0131-01 rev A SPEED SENSOR II USERS MANUAL](https://reader030.vdocument.in/reader030/viewer/2022012717/61af6ddfbe9c012dde7c05cd/html5/thumbnails/5.jpg)
Speed Sensor II User’s Manual
5
3 PCApplication
3.1 LoadingtheDeveloper’sKitCDInserttheDeveloper’sKitCDinyourPC,andtheautomaticinstallershouldbeginwithinafewseconds.Allowtheinstalltocompletenormallybyclickingonthepromptsfordefaultinstallation.TheprocessinstallsthefollowingitemsonyourPCunderC:\ProgramFiles\Stalkerandincludes:
StalkerDashboardapplicationthatcanbeusedtoconfigure,monitorandcontrolSpeedSensors.
A.pdfversionofthismanual. SpecificationsforeachoftheSpeedSensormodels. Configurationfilesforeachofthemodels. Cabledrawingsforreference.
TheinstallationprocessalsocreatesashortcuticononthedesktopfortheDashboardapplication.SeveralshortcutstotheinstalleditemsarecreatedundertheStalkertabintheWindowsStartMenu.
3.2 PollingforSpeedSensorIDOncethesensorisconnectedtothePCandpowerisconnected,double‐clicktheStalkerDashboarddesktopicontostartthedemoapplication.Themainscreenbelowappears.
PlacethemousepointerovertheSlogoandarolloverpopupmessagedisplaystheversionofcodeloadedintheSpeedSensor(e.g.Stationary232Ver:2.0.0).Thedisplayofthisversionisassurancethattheunitispoweredandcommunicatingsincetheapplicationmustpollittofindoutthisinformation
![Page 6: 011-0131-01 rev A SPEED SENSOR II USERS MANUAL](https://reader030.vdocument.in/reader030/viewer/2022012717/61af6ddfbe9c012dde7c05cd/html5/thumbnails/6.jpg)
Speed Sensor II User’s Manual
6
3.3 TroubleshootingCommunicationIssuesIftheversionisblankwhentheSpeedSensorispolledasabove,theunitisnotcommunicatingwiththePC.TheproblemcouldbeapowerproblemwiththeSpeedSensororacommunicationlinkproblembetweenthePCandSpeedSensor.
Forsuspectedcommunicationlinkproblemsortochangetheserialportorthebaudrate,clickon“Options”inthemainscreenandselect“ChangeSerialPortSettings”fromthepull‐downmenu.
ChangethePortsettingtomatchthePC’sserialportbeingusedbytheDashboardapplicationandtheBaudratetomatchthebaudratesettingintheSensor.
![Page 7: 011-0131-01 rev A SPEED SENSOR II USERS MANUAL](https://reader030.vdocument.in/reader030/viewer/2022012717/61af6ddfbe9c012dde7c05cd/html5/thumbnails/7.jpg)
Speed Sensor II User’s Manual
7
4 ConfiguringtheSpeedSensor
Whenviewingthemainscreenofthedemoapplication,thenameofaconfigurationfileisdisplayedinthetitlebar(e.g.[ConfigureStationary2322.0.0.cfg]).ThisfiledefinesalloftheconfigurablesettingsthatareavailableonaparticularmodelofSpeedSensor.Sincefeaturesandsettingsareaddedandchangedindifferentversionsofsoftware,thefilenamealsoincludestheversion(2.0.0)thatthefile’ssettingsapplyto.Theexamplesinthismanualareforagenericversionofthespeedsenor.Ifyouaretestingaspecificversionofthesensoryoumayneedtochangetoaconfigurationfilesentwiththatspeedsensorforthesystemtoworkproperly.Ifyouareusingadifferentversionofthespeedsensor,withadifferentconfigurationfile,notalloftheoptionsshownheremaybeavailable.Refertothatsensor’sspecificmanualforitsuniqueconfigurationcontrols.
Ifthefilenameisforadifferentunit,openalistofotheravailableconfigurationfilesbyselecting“SelectNewStartupConfigFile”fromtheConfigpull‐downmenu.
Thedialogboxonthenextpagewillopenandallowforaselectiontobemade.ItisimportantthatthemodelandsoftwareversionintheconfigurationfilenamematchthemodelandversionintheProductID.ThedialogboxwillcontaintheSensormodelandcurrentsoftwarerevisioninthebluetitlebar.
![Page 8: 011-0131-01 rev A SPEED SENSOR II USERS MANUAL](https://reader030.vdocument.in/reader030/viewer/2022012717/61af6ddfbe9c012dde7c05cd/html5/thumbnails/8.jpg)
Speed Sensor II User’s Manual
8
Ifthereareno.cfgfilesinthelist,makesurethe“Lookin”windowissetfortheConfigurationUtilitiesfolderunderC:\ProgramFiles\Stalker–thestandardinstallationlocationforthesefiles,orC:\ProgramFiles(x86)\Stalkerfora64bitOS.Ifthecorrectfileisstillunavailable,alowerversionnumberforthatmodelwillwork,butitmaynotprovideaccesstonewerfeatures.ThematchingconfigurationfileisalwaysavailablefromStalker.Contactussowecansendittoyou.
![Page 9: 011-0131-01 rev A SPEED SENSOR II USERS MANUAL](https://reader030.vdocument.in/reader030/viewer/2022012717/61af6ddfbe9c012dde7c05cd/html5/thumbnails/9.jpg)
Speed Sensor II User’s Manual
9
4.1 ReadingtheCurrentConfigurationFromtheConfigpull‐downmenu,select“EditFirmwareValues”.TheapplicationwillpolltheSpeedSensortoreadallthesettingsdefinedintheconfigurationfileandthendisplaytheConfigurationwindowbelow.
Thesettingsaregroupedbytypeandthedifferenttypescanbeselectedbyclickingontheappropriatetab.Moretabscanbemadevisiblebyclickingontheleftandrightarrowsnexttothelasttabontheright.
![Page 10: 011-0131-01 rev A SPEED SENSOR II USERS MANUAL](https://reader030.vdocument.in/reader030/viewer/2022012717/61af6ddfbe9c012dde7c05cd/html5/thumbnails/10.jpg)
Speed Sensor II User’s Manual
10
4.2 ChangingandSavingtheConfigurationThesettingsintheSpeedSensorcanbechangedbyselectingothervaluesfromthesettings’pull‐downmenusasshownbelow,forexample,changingtheunitsfromMPHtokm/H(KilometersperHour).ClicktheOptionsMenuandselecttheUploadProposedValuestoSensortosavethesettingschangestotheSpeedSensor.ThechangescanbeconfirmedbyobservingthattheSensorValuesarenowequaltotheProposedValues.
WhenUploadProposedValuestoSensorbuttonisclicked,theStalkerDashboardapplicationsendsseparatecommandstotheSpeedSensortoseteachvalue.TheSpeedSensorrespondstoeachcommandwithitsneworcurrentsettingvalue.ThenewsettingsarestoredintheSpeedSensor’sinternalmemoryandarerememberedevenwhentheunitisturnedoffandbackon.
IftheSpeedSensorrespondstotheapplicationwithavaluedifferentfromthedesiredvalue,anerrormaybeseenasshownbelow.
![Page 11: 011-0131-01 rev A SPEED SENSOR II USERS MANUAL](https://reader030.vdocument.in/reader030/viewer/2022012717/61af6ddfbe9c012dde7c05cd/html5/thumbnails/11.jpg)
Speed Sensor II User’s Manual
11
Thiswarningcanbecausedbythesereasons:
Iftheapplicationtriestochangeasettingthatisnotdefinedforaparticularmodelorversion,theSpeedSensorreturnsthevalue“255”meaningthatitdoesnotunderstandtherequest.MakesuretheapplicationisusingthecorrectconfigurationfileandthatallsettingsintheconfigurationfileareapplicabletothatSpeedSensormodel.
IfanillegalvalueissenttotheSpeedSensor,itignoresitandrespondswithalegal
value.SomesettingsrequiretheinternalstatemachineoftheSpeedSensortorunbeforethesettingisactuallychanged.TheSpeedSensorcanrespondtotheapplication’scommandmessagebeforethestatemachinehasrun,sotheinitialresponsemaynotbethedesiredsetting.Re‐opentheConfigurationswindowafterthewarningtoverifythatthesettingdidactuallychange.ThesesettingsareMode,Zone,TransmitterControl,StrongLock,FastLock,TestandForkEnable.
Somesettingsareread‐onlysettings,andtheSpeedSensorwillrespondwithits
internalvalueregardlessofwhatvaluewasrequested.ThesesettingsareGetProductIDandGetCurrentAGCGain.RefertotheendoftheSpeedSensorConfigurationFilesectionfordetailsoncontrollingwarningscausedbythesesettings.
![Page 12: 011-0131-01 rev A SPEED SENSOR II USERS MANUAL](https://reader030.vdocument.in/reader030/viewer/2022012717/61af6ddfbe9c012dde7c05cd/html5/thumbnails/12.jpg)
Speed Sensor II User’s Manual
12
4.3 ConfigurationSettingsTherearemanySpeedSensorconfigurationsettings.SomeapplytoallSpeedSensorsbutothersarespecifictocertainmodels.Allsettingsforallmodelsaredescribedindetailin
BasicConfiguration SerialPortConfiguration TargetRecognition TargetFiltering SpeedPresentation LockingTargets SpeedAlarm Audio TXPowerSave Testing System
4.4 ChangingtheBaudRateSincethebaudrateoftheSpeedSensorandthebaudrateoftheDashboardapplicationmustbethesameforcommunicationstowork,usethefollowingstepstochangethebaudrate.
OpentheConfigSettingsgridasdescribedaboveandclickontheSerialPortConfigurationtabtoseetheserialportsettings.
Changethebaudratetothenewdesiredvalueandsavethesetting.AtthispointtheSpeedSensorandtheDashboardapplicationarestillcommunicatingwiththepreviousbaudrate;thebaudrateoftheSpeedSensorhasnotchangedyet.
TurntheSpeedSensoroffandbackontocompletethebaudratechangeintheunit. ConfiguretheScoreboardapplication’sbaudratetothenewdesiredvalueasdescribed
inSection3.3above.Youmayneedtocloseandreopentheapplicationtocompletetheprocess.
4.5 DefaultSettingsTherearetwotypesofdefaultvaluesfortheSpeedSensors.Factorydefaultsarehard‐codedintotheunitandcannotbemodified.ConfigurationFiledefaultsaresavedintheconfigurationfilesdiscussedabove.Theycanbechangedinthefileandsavedforcustomuserdefaultvalues.
4.5.1 FactoryDefaultsThefactorydefaultsforeachsettingandeachproductarelistedinAppendixD.Toreturnallvaluestotheirfactorydefaults,performthefollowingsequence:TurntheSpeedSensoroffusingtheswitchontheProgrammingBox.PressandholdtheredResetbuttononthebox(orgroundtheAUXpin)whileturningtheunitbackon.Releasetheredbuttonafter2or3seconds.Turntheunitoffbrieflyandthenbackonagain.BecarefulusingthismethodbecausealloftheSpeedSensor’ssettingsarechangedbacktofactorydefaults.Ifothersettingshadbeenconfiguredforacustomapplication,theywillneedtobesetagain.
![Page 13: 011-0131-01 rev A SPEED SENSOR II USERS MANUAL](https://reader030.vdocument.in/reader030/viewer/2022012717/61af6ddfbe9c012dde7c05cd/html5/thumbnails/13.jpg)
Speed Sensor II User’s Manual
13
4.5.2 ConfigurationFileDefaultsToconfiguretheSpeedSensorwiththedefaultvaluesinthecurrentlyselectedconfigurationfile,selectthe“InitializeRadarWithConfigFileDefaults”fromtheConfigpulldownmenu.Makesurethatthedesiredconfigurationfileisselected(asdescribedinthebeginningofSection5)beforeinitializingwithdefaults.
ThedefaultvaluesinthestandardconfigurationfilesavailablefromStalkerRadarareequaltothefactorydefaultslistedinAppendixD.Ifchangesaremadetovaluesforacustomconfiguration,theymaybesavedasdefaultvaluesinanewconfigurationfileforlateruse.Onceallchangesaremade,select“SaveSensorValuesToNewFileAsDefaults”fromtheOptionspull‐downmenu.
Savethenewconfigurationfilewithanamedescribingthecustomapplication.Thenexttime“SelectNewStartupConfigFile”isselectedfromtheOptionspull‐down,thenewfilewillbeavailablealso.Iftheboxaboveischeckedfor“SaveAsStartupConfigFile”,thenewlycreatedfilenamewillappearinthetitlebarandthatfileisthenusedfortheconfigurationtasks.
![Page 14: 011-0131-01 rev A SPEED SENSOR II USERS MANUAL](https://reader030.vdocument.in/reader030/viewer/2022012717/61af6ddfbe9c012dde7c05cd/html5/thumbnails/14.jpg)
Speed Sensor II User’s Manual
14
4.6 PrintingSettingValuesThecurrentconfigurationsettingsinaSpeedSensorcaneasilybeprintedforarecordofvalues.Apreviewofthepagestobeprintedcanbeselectedbyclickingon“PrintPreview”.Toprintthepages,select“Print”fromtheOptionspull‐downmenu.AWindowsPrintscreenwillappearforyoutoselectaprintertoprintthefileto.Selectthedesiredprinterorusethedefaultprinter.Thetableofconfigurationvalueswillprintwithaheaderatthetopofeachpagethatshowsthedate,Sensortype,andsoftwareversion.
4.7 DemoApplicationSoftKeysWhenusingtheStalkerDashboardapplicationtocommunicatewiththeunit,severalsoftkeysareavailableforconfigurationandcontroloftheunit:
![Page 15: 011-0131-01 rev A SPEED SENSOR II USERS MANUAL](https://reader030.vdocument.in/reader030/viewer/2022012717/61af6ddfbe9c012dde7c05cd/html5/thumbnails/15.jpg)
Speed Sensor II User’s Manual
15
ForkOn/OFF–Togglestheforkmodeonandoff.Usedwhentestingwithatuningfork.Mode–clickingthisbuttonalternatesthemodeoftheunitbetweenStationaryandMoving.ThiscapabilityisonlyavailableintheTrafficSpeedSensorwhichhasbothmodesofoperation.Units–SelectsthetypeofunitsthattheSensorwilloutputandbedisplayedinthespeedwindows.Transmit/Hold–clickingthisbuttonturnsonandofftheradartransmitter.ThestatusdisplaysasTransmitorHold.Zone–WheninStationarymode,clickingthisbuttoncyclesthroughtheAway,ClosingandBothzones.WheninMovingmode,italternatesthezonebetweenSamelaneandOppositelane.LockingSpeeds–Thoughnotshownasasoftkey,aStrongtargetorFasttargetspeedcanbelockedbyclickingthewindowshowingthedesiredspeedtobelocked.ThelockedspeedwillbeshownintheLockwindow.Toclearthelockedspeed,clicktheLockspeedwindow.
4.8 ForkTestAForkTestcanberuntoensureproperoperationofaSpeedSensorradar.TuningforksarecalibratedtoringatacertainfrequencythatsimulatesaDopplerreturnfromamovingobject.Sincetheyarenottrulydirectionalsignalsandsincetheradarnormallyfiltersoutnon‐directionalsignals,a“forkmode”isprovidedtoeasilyreadtuningforks.
WhentheForkModestatusonthedemoapplication’smainscreenisOn,strikeaforkandholditinfrontoftheradar’slenstoseeitscalibratedspeedreadoutinthetargetwindow.Ifthespeedstampedonthetuningforkmatchesthespeeddisplayed,theradarisseeingtargetsandreportingthemproperly.
![Page 16: 011-0131-01 rev A SPEED SENSOR II USERS MANUAL](https://reader030.vdocument.in/reader030/viewer/2022012717/61af6ddfbe9c012dde7c05cd/html5/thumbnails/16.jpg)
Speed Sensor II User’s Manual
16
ForkModeisautomaticallyturnedonforoneminutewhentheSpeedSensorispoweredup.Thisallowsaquickforktestbeforethemodeisautomaticallyturnedoffandtheradaragainprocessesonlydirectionaltargets.Ifalongerforkperiodisdesired,turnonforkmodeusingtheForkEnableconfigurationsetting(setting47).Whenenabledinthismanner,forkmodestaysonfor10minutesbeforeitautomaticallyturnsoffagain.
4.9 MonitoringSpeedDataTheradartransmittermustbeonfortheSpeedSensortoregisterspeeds.ThedemoPCapplicationcanbeusedtomonitorspeedsthattheSpeedSensordetects.Otherequipmentorapplicationscanalsomonitorthespeeddatafromtheunitbydecodingthemessagesittransmitsovertheseriallink.
Severalmessageformatsareavailableandcanbeselected.RefertotheSpeedSensortechnicalmanualforthecontentandorganizationofthefieldsforthedifferentformats.TheyvaryfromsimpleASCIIcharacterstringstolongerformatsreportingmultiplespeedsandstatusinformation.Therearealsostreamingformatsandpollingformats.
TheRS‐232modelscanstreamdatainanyformatexceptEEwhichisreservedasapolling‐onlyformat.Whenevertheradartransmitterison,theSpeedSensorstreamsoutspeedmessagesintheselectedmessageformatatafixednumberofmessageseachsecond.
TheRS‐232modelscanalsocommunicateusingtheFormatEEhandshaking(orpolling)method.Insteadofautomaticallystreamingdataout,itsendsasingleFormatEEspeedmessagepacketonlywhenthecontrollerasksforone.TheStationarySpeedSensorreportsthestrongtargetspeedvalue,andtheSpeedometerandTrafficSpeedSensorsreportthevehiclespeedvalue.
ToenableFormatEEpolling,makesuretheradartransmitterisonandthattheMessageFormatisconfiguredforEE.Thenselect“StartEEPolling”fromtheOptionspull‐downmenuonthemainscreenasshownbelow.TheDashboardapplicationwillthenbeginsendingEEFormatRequestsanddisplayingthevaluesreturnedfromtheSpeedSensor.Tostopthepollingfromtheapplication,select“StopPolling”fromthesamemenu.
![Page 17: 011-0131-01 rev A SPEED SENSOR II USERS MANUAL](https://reader030.vdocument.in/reader030/viewer/2022012717/61af6ddfbe9c012dde7c05cd/html5/thumbnails/17.jpg)
Speed Sensor II User’s Manual
17
TheRS‐485modelscanonlyusehandshakingmethodssincetheyarealwaysaslaveonthelink.Theyneversenddataunlessthecontrollerasksforit.TheycancommunicateusingFormatEEpollingasdescribedabove,butonlyiftheunit’saddressis2,thefactorydefault.
TheStationaryRS‐485modelcanalsousethemoreflexibleEApolling.Withthismethod,thecontrollersendsanEArequestasdescribedinAppendixB,andtheSpeedSensorreturnsasinglemessageofwhateverSerialPortOutputFormatisselected.SincetheEArequesthasaddressfields,thecontrollercanpollanyindividualunitonapoint‐to‐multipointlinkandgetbackaspeedreportfromonlythatunit.TheDashboardapplicationdoesnotsupportEApolling.
TheStalkerDashboardapplicationdisplaysthespeedsitreceivesintheappropriatespeedwindows.ForaStationarySpeedSensor,thestrongesttargettheradarseesshowsintheSTRONGwindow.Ifafaster,weakersignalisdetected,itshowsintheFASTwindow.Andifeitherastrongorfasttargetislocked,thatspeedshowsintheLOCKwindow.ATrafficSpeedSensordisplaysallofthesespeedsplusthevehiclespeedintheVEHICLESPEEDwindow.TheSpeedometerSpeedSensoronlyreportsvehiclespeedwhichdisplaysintheVEHICLESPEEDwindow.
Intheexamplebelow,aStationarySpeedSensorisreportingastrongtargetspeedof25MPHandafastertargetspeed(whichhasbeenlocked)of40MPH.Notethearrowsabovethespeedwindows.Thedownarrowssignifythatthetargetsareapproachingtheradar(closingspeeds).Uparrowssignifytargetsmovingaway(awayspeeds).
![Page 18: 011-0131-01 rev A SPEED SENSOR II USERS MANUAL](https://reader030.vdocument.in/reader030/viewer/2022012717/61af6ddfbe9c012dde7c05cd/html5/thumbnails/18.jpg)
Speed Sensor II User’s Manual
18
4.10 LoggingSpeedDataWhentheSpeedSensorissendingspeeddataintheEEFormat(thehandshakeprotocol),theDashboardapplicationcanlogthedatatoafileforlaterreview.Thiscomma‐delimitedfilelistseachspeedentrywithatimestampandcaneasilybeimportedtoaspreadsheetortexteditor.Loggingisnotenabledbydefault,soafewsettingsintheapplication’scontrolfilearenecessarytogetitstarted.Followthestepsbelowtoenablelogging:
LocatethefilenamedDashboard.iniinthe“C:\ProgramFiles\Stalker\Dashboard\Application”folder.
Ifthefileisnotinthatlocation,rightclickonthedemoapplicationdesktopiconandselect“Properties”toopenthepropertieswindowfortheicon.ClickontheShortcuttabandlookinthe“Startin:”fieldforthelocationoftheapplicationexecutablefileandtheDashboard.inifile.
OpentheDashboard.inifileinanytexteditorsuchasWordPadorNotepad. FindtheENABLE_SPEED_LOGGINGlineandensuretheparameterisset=1. Ifloggingofzerospeedsisdesired,settheLOG_ALL_SPEED_DATAparameter=1.Ifonly
non‐zerospeedsaredesired,setit=0. TypeinthedesirednameofthelogfileaftertheDATA_LOG_FILEparameter.The
defaultisSpeedLog.csv.ThelogfilewillbecreatedinthesamefolderastheapplicationexecutableandDashboard.inifiles.
SetthepollingintervalwiththeEE_FORMAT_INTERVALparameter.Thenumberrepresentsmillisecondsbetweenpolls,andthedefaultvalueis100ms(tentimespersecond).
Toinitiatelogging,makesuretheradartransmitterisonandthattheSerialPortOutputFormatisconfiguredforEE.Thenselect“StartEEPolling”intheActionspull‐downmenu.Tostoplogging,select“StopEEPolling”.ThedemoapplicationappendsnewdatatothelogeachtimetheEEFormatisstarted.
![Page 19: 011-0131-01 rev A SPEED SENSOR II USERS MANUAL](https://reader030.vdocument.in/reader030/viewer/2022012717/61af6ddfbe9c012dde7c05cd/html5/thumbnails/19.jpg)
Speed Sensor II User’s Manual
19
ThefilecreatedisacommadelimitedfileandcanbeopenedwithaTXTprogramofExcel.Thedatawillconsistofdate,time,speedanddirectionandlooklikethis:
2012/09/24 12:35:39:131,32,1 2012/09/24 12:35:39:241,33,1 2012/09/24 12:35:39:381,33,1 2012/09/24 12:35:39:475,33,1 2012/09/24 12:35:39:569,9,-1 2012/09/24 12:35:39:709,10,-1 2012/09/24 12:35:39:803,11,-1 2012/09/24 12:35:39:897,11,-1 2012/09/24 12:35:40:006,12,-1
5 ConfiguringtheStalkerDashboardApplication
TheStalkerDashboardapplicationforcommunicatingwithandconfiguringSpeedSensorsconsistsofasetoffileswhichresideonthePC.TheDeveloper’sKitCDprovidedwiththeSpeedSensorProgrammingBoxKitsinstallsallofthefileslistedbelow(initalics)ontheuser’sPCundertheC:\ProgramFiles\Stalkerfolder.
StalkerDashboard.exeisthePCdemoapplicationexecutablefileusedtocontrolandcommunicatewiththeSpeedSensors.Dashboard.iniisthecontrolfileforthedemoapplication.ThesetwofilesareinstalledintheC:\ProgramFiles\Stalker\Dashboard\Applicationfolder.
TheexecutablefileandtheDashboard.inicontrolfileareusedasapairwhentheapplicationisrunning.Theexecutablefilereadsparametersfromthecontrolfileduringinitialization.Andtheexecutablefilealsoupdatesthecontrolfileduringoperation.Forthisreason,onlyoneexecutablefileinafoldershouldberunatatime.IfmorethanoneexecutableisrunningandtryingtousethesameDashboard.inifile,theexecutableswillinterferewitheachother.
ItispossibletorunmorethanoneapplicationatatimeononePCif,forexample,thereisanotherSpeedSensorconnectedtodifferentserialport.SimplycopytheexecutablefileandtheDashboard.inifiletoadifferentfolderwheretheycanrunwithoutinterference.
TherearealsouniquestandardconfigurationfilesforeachmodelandsoftwareversionofSpeedSensor:ConfigureTraffic232x.x.x.cfgisforaTrafficSpeedSensorversionx.x.x.ConfigureStationary232x.x.x.cfgisforanRS‐232StationarySpeedSensor.ConfigureStationary485x.x.x.cfgisforanRS‐485StationarySpeedSensor.ConfigureSpeedometer232x.x.x.cfgisforanRS‐232SpeedometerSpeedSensor.ConfigureSpeedometer485x.x.x.cfgisforanRS‐485SpeedometerSpeedSensor.ThesefilesareinstalledintheC:\ProgramFiles\Stalker\ConfigurationUtilitiesfolder.
![Page 20: 011-0131-01 rev A SPEED SENSOR II USERS MANUAL](https://reader030.vdocument.in/reader030/viewer/2022012717/61af6ddfbe9c012dde7c05cd/html5/thumbnails/20.jpg)
Speed Sensor II User’s Manual
20
5.1 ApplicationControlFileThecontrolfile,Dashboard.ini,isanASCIItextfilethatmaybeeditedwithanytexteditorsuchasWordPadorNotepad.IthasseveralcontrolparametersthatcanbechangedtoaffecttheoperationoftheSpeedSensorapplication.Seeacopyofthefilebelowwithexplanationsoftheparametersfollowing.
[Stalker]PORT=COM1BAUD=9600
SOURCE_ID=1DESTINATION_ID=2
CONFIG_FILE=C:\ProgramFiles\Stalker\ConfigurationUtilities\ConfigureStationary2322.0.0.cfgCONFIG_FILE_LOCATION=C:\ProgramFiles\Stalker\ConfigurationUtilities
GET_CFG_INTERVAL=5000RESPONSE_TIMEOUT=500RETRY=2
EE_FORMAT_INTERVAL=100
ENABLE_SPEED_LOGGING=1LOG_ALL_SPEED_DATA=0DATA_LOG_FILE=SpeedLog.csv
PORTdefinesthePCserialportusedforcommunicationwiththeSpeedSensor.WhentheserialportischangedusingtheOptionspull‐down“ChangeSerialPortSettings”function,thisparameterintheDashboard.inifileisautomaticallychanged.Itcanalsobechangedbyeditingthefile.AftertheCOMportischanged,theapplicationneedstobeclosedandre‐openedforthenewlyselectedporttobeused.BAUDdefinesthebaudratetobeusedforcommunicationwiththeSpeedSensor.AswithPORTabove,thisparametercanalsobechangedviatheOptionspull‐down“ChangeSerialPortSettings”functionorbyeditingthefile.Andafterchangingthebaudrate,theapplicationneedstobeclosedandre‐openedforthesettingtotakeeffect.
SOURCE_IDisalwayssetto1andDESTINATION_IDisalwayssetto2.WhencommunicatingwithaSpeedSensor,theapplicationisalwaysthemasterofthelink(ID1)andtheSpeedSensorisalwaystheslave(ID2).Donotchangethesevalues.
CONFIG_FILEdefinestheSpeedSensorconfigurationfileusedduringasession,andCONFIG_FILE_LOCATIONdefinesthepathtothatfile.Theseparametersareupdatedbytheapplicationwhen“SelectNewStartupConfigFile”isselectedfromtheConfigpull‐downmenu.Thecontentofconfigurationfilesisdiscussedindetailinthenextsection.
GET_CFG_INTERVALdefineshowoften(inmilliseconds)theapplicationpollstheSpeedSensortoupdatethestatusfieldsinthemainwindow.Thisparameterappliestothestatusfieldsonly(Units,Mode,Zone…)–notthespeedwindows.Thedefaultis5000ms(5seconds).Thisparametervaluecanbeincreasedtoreducethemessagetrafficonthelink.RESPONSE_TIMEOUTisthetimeinmillisecondsthattheapplicationwillwaitforaresponsefromtheSpeedSensorbeforearetryorfailure.Thedefaultis500ms(½second).RETRYdefinesthenumberoftimestheapplicationwillresendaconfigurationsettingtotheSpeedSensorifitdoesn’tgetaresponse.
![Page 21: 011-0131-01 rev A SPEED SENSOR II USERS MANUAL](https://reader030.vdocument.in/reader030/viewer/2022012717/61af6ddfbe9c012dde7c05cd/html5/thumbnails/21.jpg)
Speed Sensor II User’s Manual
21
EE_FORMAT_INTERVALdefineshowoften(inmilliseconds)theapplicationpollstheSpeedSensorforaspeedreportinEEFormat.Pollingbeginsafterselecting“StartEEPolling”fromtheActionspull‐downmenu,andpollingstopsafterselecting“StopEEPolling”.Thedefaultvalueis100ms(1/10secondor10timespersecond).ThevaluecanbeincreasedordecreasedtospeeduporslowdowntherateofEEFormatpolling.
ENABLE_SPEED_LOGGINGdefineswhetheraspeedlogfileisgeneratedforthecurrentsession.Loggingisenabledwhentheparameterisset=1anddisabledwhenset=0.LoggingonlytakesplaceiftheSpeedSensor’sSerialPortDataFormatissetforEEFormat.LOG_ALL_SPEED_DATAisusedtoinhibitlogging0speeds.Whenset=1allspeedsareloggedincluding0speeds.Whenset=0onlyspeedsabove0arelogged,andthelengthofthelogfileisreduced.DATA_LOG_FILEdefinesthefilenameforthespeedlog.ThisfilewillbesavedinthedirectorywheretheapplicationfileandtheDashboard.inifilereside.
5.2 SpeedSensorConfigurationFile1. TheSpeedSensorconfigurationfilesarealsoASCIIfileswhichcanbeeditedwithatexteditor.
StalkerRadarprovidesadifferentfileforeachdifferentmodelofSpeedSensorandforeachdifferentsoftwareversionforeachmodel.ThesestandardconfigurationfilesdefinethesettingsfromAppendixDthattheapplicationcancontrolinaunit.Ashortportionofaconfigurationfileisshownbelow.Notethatthefileisorganizedinaseriesoftextblocks:threeblocksintheexamplebelow.
![Page 22: 011-0131-01 rev A SPEED SENSOR II USERS MANUAL](https://reader030.vdocument.in/reader030/viewer/2022012717/61af6ddfbe9c012dde7c05cd/html5/thumbnails/22.jpg)
Speed Sensor II User’s Manual
22
Theorderoftheblocksinthe.cfgfiledeterminestheorderinwhichthesettingsandtheirvalueswillbedisplayedintheConfigurationwindow.Aslongastheblocksaremovedasunits,theycanbearrangedinanyorder.
BlocksforthesettingsusedmostoftencouldbeplacedatthetopofthesectionsotheirvaluesappearatthetopoftheConfigurationswindow.Blocksforsettingsthatareneverusedcouldevenbedeletedfromthefiletospeedupthe“EditFirmwareValues”process.WerecommendcopyingthestandardfileprovidedbyStalkerRadartoafilewithanewnamebeforemakingchanges.Inthatway,manycustomconfigurationfilescanbecreatedfordifferentuses,andthestandardfileisalwaysavailabletofallbackonforcompletecontrol.
Eachblockrepresentsadifferentconfigurationsettingandhasthefollowingformat:
[TransmitterControl]PACKET_TYPE=1COMMAND_ID=42ANTENNA_NUMBER=1VALUE_BYTES=1DATA_TYPE=1VALUE_MIN=VALUE_MAX=VALUE_ITEMS_DISPLAY=Hold,TransmitVALUE_ITEMS_FIRMWARE=0,1DEFAULT_VALUE=1DISPLAY=1
Thefirstlineintheblockdefinesthenameofthesettinginbrackets.ThisisthesettingdescriptionthatdisplaysintheleftcolumnoftheConfigurationsscreen,anditcanbechangedtoanynamedesired.
PACKET_TYPEshouldbeset=1.Donotchangethisvalue.ItisusedinthePacketTypefieldoftheConfigurationProtocoldescribedinAppendixEwhentheapplicationisbuildingcommandstosendtotheSpeedSensor.COMMAND_IDistheSettingID(indecimalformat)fromAppendixDthatcorrespondstothesettingdescription.ANTENNA_NUMBERshouldbeset=1.Donotchangethisvalue.ItisusedintheAntennaNumberfieldoftheConfigurationProtocoldescribedinAppendixEwhentheapplicationisbuildingcommandstosendtotheSpeedSensor.VALUE_BYTESisthenumberofbytesthatthesettingvalueuses.DonotchangethisvaluefromthevalueprovidedinthestandardconfigurationfilesfromStalkerRadar.DATA_TYPEcontrolsthebehaviorofthevaluefields.Whenset=1(listtype),onlythevalueslistedinVALUE_ITEMS_DISPLAYarevalid.Whenset=2(free‐formnumerictype),inadditiontothevaluesinthelist(ifany),theusercanalsoenteranynumericvalueintherangefromVALUE_MINthroughVALUE_MAX.VALUE_MINdefinestheminimumacceptablevaluewhenDATA_TYPE=2.VALUE_MAXdefinesthemaximumacceptablevaluewhenDATA_TYPE=2.VALUE_ITEMS_DISPLAYdefinesthetextthatwillappearaspull‐downselectionsintherowforagivensettingintheConfigurationswindow.Thevaluesareseparatedbycommaswithnospacesandmaybesettoanydesiredtext.VALUE_ITEMS_FIRMWAREdefinestheactualvaluestheapplicationusestocommunicatewiththeSpeedSensor.Thesevaluesarealsoseparatedbycommas,andtheordercorrelatesona
![Page 23: 011-0131-01 rev A SPEED SENSOR II USERS MANUAL](https://reader030.vdocument.in/reader030/viewer/2022012717/61af6ddfbe9c012dde7c05cd/html5/thumbnails/23.jpg)
Speed Sensor II User’s Manual
23
onetoonebasiswiththeorderofthelistforVALUE_ITEMS_DISPLAY.TheavailablevaluesforeachsettingaredefinedinAppendicesCandD.DEFAULT_VALUEisthedefaultvaluedescribedintheConfigurationFileDefaultssection.Itmaybesettoanylegalvalueforthesetting–eitherfromtheVALUE_ITEMS_FIRMWARElistorbetweenVALUE_MINandVALUE_MAX.DISPLAYdefineswhetherthesettingisdisplayedintheConfigurationsscreen.Whenset=1,thesettingisdisplayed.Whenset=0,thesettingisnotdisplayed.Thismethodcanbeusedtoskipdisplayingsettingsofnointerestwithouthavingtodeletethewholeblockfromthefile.
Formostcommands,theSpeedSensorisabletochangethesettingandreportthenew,desiredvalue.However,somesettingsareonlyusedforpollingormonitoringthestatusoftheunitandcannotactuallychangethesettingintheunit.Fortheseread‐onlysettings,theSpeedSensorstillsendsaresponse,butitrespondswiththeinternalsettingvalueandmayresultintheapplicationprogramdisplayingthefollowingscreen.
Thesesettingsare#37GetProductIDand#50GetCurrentAGCGain.EnsurethattheDISPLAYparameterforthesesettings=0sothattheapplicationwillnottrytochangethemandgenerateawarning.ChooseContinuetofinishtheoperationbutmakethenecessarychangetotheconfigurationfiletopreventthewarningfromappearingagain.
![Page 24: 011-0131-01 rev A SPEED SENSOR II USERS MANUAL](https://reader030.vdocument.in/reader030/viewer/2022012717/61af6ddfbe9c012dde7c05cd/html5/thumbnails/24.jpg)
Speed Sensor II User’s Manual
24
5.3 SoftwareupdatesTheDashboardprogramhastheuniqueabilityofuploadingnewsoftwaretoSpeedSensorswithversion2.0.0orlatercodealreadyinstalled.IfyourSpeedSensorhassoftwarethatisearlierthan2.0.0,otherPCApplicationslocatedontheProgramCDcanbeusedforcommunicatingtotheSpeedSensor.Checkwiththefactorytodetermineifversion2.0.0isavailableforyourtypeofSpeedSensor.Ifsoftwareversion2.0.0isavailable,theSensorcanalsobesenttothefactoryforupgradingtothelatestprogram.ThissectiondetailstheprocessofuploadinganewsoftwareprogramtoyourSpeedSensor.Checkingforanewversionofsoftware:
ContacttheCustomerServiceDepartmentatStalkerRadarandinquireaboutanewversionofsoftware.PleasehaveyourcurrentversionavailablewhenaskedsoitcanbedeterminedifthereisanewloadforyourSensor.AnewversioncanbesentbyemailandwillinstallonyourharddriveunderC:\ProgramFiles\Stalker\....inasubfolderthatgroupsthedifferentversionstogether.ThedashboardversionnumbercanbefoundbyclickingonAboutinthemainmenubar.
DashboardSetupOncethenewcodehasbeensavedtoyourharddisk,opentheDashboardprogram.Clickonthe“Options”menuandthenclickon“ReprogramRadar”.Anewwindowwillappearasseenbelow.FollowtheinstructionstodeterminewhichtypeofSensoryouhave.Clickontheappropriateselectionboxforyourradarintheupperrightcornerofthescreen.Clickon“OK”toproceed.
Anotherwindowwillopentoshowtheavailablefilesthatcanbeuploadedtothesensor.Selecttheprogramthatistobeuploadedtotheunit,inthiscase“s3_sta_200.p”locatedundertheStalkerS3Stationarysection,seepicturebelow.Inthisexample,thisprogramisthelatestversionavailablefortheStationarytypeofSensor.Thefolderstructuremayvarybysystem.Doubleclickontheiconofthedesiredversionandclickon“Ok”onthepopupwindow.Theprogramwillstarttouploadthecodeandaprogressmeterwillshowatthebottomofthewindow.ProgramsfortheRS485versionsoftheSpeedSensorwillhavethenumber“4”inthefilenamejustbeforetherevisionnumber,e.g.“s3_sta4_200.p”.
![Page 25: 011-0131-01 rev A SPEED SENSOR II USERS MANUAL](https://reader030.vdocument.in/reader030/viewer/2022012717/61af6ddfbe9c012dde7c05cd/html5/thumbnails/25.jpg)
Speed Sensor II User’s Manual
25
Whentheuploadiscomplete,anotherpopupwindowwillappeartoannounceasuccessfulupload.
OneoftheothertypesofSensors,SpeedometerorTraffic,maybeinstalledintheSensoraswellbuttheproperconfigurationfilewillneedtobeappliedforproperoperation.Iftheconfigurationisincorrectfortheprogramjustuploaded,awarningscreenwillappearandallowyoutobrowseforanappropriateconfiguration.
![Page 26: 011-0131-01 rev A SPEED SENSOR II USERS MANUAL](https://reader030.vdocument.in/reader030/viewer/2022012717/61af6ddfbe9c012dde7c05cd/html5/thumbnails/26.jpg)
Speed Sensor II User’s Manual
26
6 FCCRequirementsThis device is approved as an intentional radiator under FCC Part 15 with FCC identifier IBQACMI007.
No additional licensing is required to operate this device.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.