Download - 1279370006886
-
7/31/2019 1279370006886
1/9
Agreeable Sheep Instructions 1 Rob Ives / Flying Pig 2007
You will need a craft knife or other sharp knife, a pair of scissors, some glue
and a glue spreader.
The best type of glue to use is white school glue (PVA.)
Print out the parts sheets onto thin cardboard. Photocopier card is ideal.
Notice that the parts pages are marked front and back. Print out a front page,
flip it over, then print the back onto the same sheet. Leave the ink to dry
completely before continuing.
Before cutting anything out, score along all the dotted
lines and cut out any holes with a craft knife. Both these
jobs are easier to do on full sheets of card.
Dashed lines are hill folds, dotted lines are valley folds.
Cut along the solid lines. Grey areas show where to
glue.
Cut
out
Dashed lines are
hill folds
Dotted lines are
valley folds
Black lines show
where to cut.
Shaded areas show
where to glue.
InstructionsInstructions
1
2
Youll need a coin
about this size.
Fold round and glue the
body inner together. (1)
Glue the body inner into
the body. Use the two very
small dots on the outside
of the body to line up the
diagonal corners of the
body inner. (3) You might
need to hold the body up
to the light to see through
it.
Roll the body round and
glue it to the other side
of the body inner. (3)
Use thes small dots
for alignment.
-
7/31/2019 1279370006886
2/9
Agreeable Sheep Instructions 2 Rob Ives / Flying Pig 2007
3 4
5
7
6
Assemble the head. (4)
Glue the neck to the head.
(5)
Glue the neck to the body
inner. (6)
Head
Neck
Body Inner
Glue the Cam Follower into
place in the box (18 - see
box. 7)
Fold round and glue the
Push-rod. (19)
Thread the Push-rod up
through the hole in the top of
the box and glue it first to the
inside of the Head (20) then to
the Cam Follower. (21 - see
the picture in box 7 for thecorrect orientation of these
parts.)
Push-rod
Cam Shaft
Cam
Fold the two flaps at the
bottom of the Box round andglue them into place. (7)
Glue the two halves of the
Box together. (8)
Glue on the Box Top. (9-10)
Fold the bottom flaps over
and glue them into place.
(11)
Fold the side supports
round and glue them
down. (12)
Glue the sheep to the Box
top. (13-14)
Find a coin of approximately 20mm diameter. A penny in
the UK or a cent in Europe and the USA will be ideal.
Wrap the Coin Holder round the coin and glue it down. (15)
Glue the coin into the centre of
the Cam Follower. (16)
Fold round and glue the
Cam Follower. (17)
Push-rod
Cam Follower
Fold round and glue the
Cam Shaft. (22)
Glue on the Cam (23)
Thread the Cam Shaft into
the box making sure thatthe green end goes to the
hole with the green ring.
Glue the two washers
onto the cam shaft. (24)
-
7/31/2019 1279370006886
3/9
Agreeable Sheep Instructions 3 Rob Ives / Flying Pig 2007
8
Fold the two
square sections
into each other
and glue. (27)
Fold the long flap
round and glue into
place. (28)
Glue the handle into
place. (29)
Not one to stand out of the crowd, our woolly friendagrees with everything you say..."Is this a good colour scheme?" "Yes!""Would you like to go for a walk?" "Yes!""Are you having a good time?" "Yes!""Does my bum look big in this?" ...probably bestnot to ask.With this agreeable model you need never get asecond opinion again.Baa baa baa!
Rob Ives / Flying Pig 2007Flying PigBroughton MoorMaryportCumbriaCA15 7RU UKt. 01900 814333f. 01900 557313www.flying-pig.co.uk
Assemble the handle inthree steps.
Glue the two square
sections as shown.
(25-26) Finish off the model by gluing
the Box Back into place on the
back of the model. (30)
-
7/31/2019 1279370006886
4/9
The Agreeable Sheep : Parts 1 Rob Ives / Flying Pig 2007
Agreeable SheepAgreeable Sheep
www.flying-pig.co.uk
10
8
12 12
12
12
Cut
outCut
out
Cut
out
Cut
out
Cut
out
11 11
7
11
11
7
9.
8
10
10
13
13
14
14
15
16
18
Box
Box
Coin Holder
Box Top
30
30
-
7/31/2019 1279370006886
5/9
15
10
8
7
12
12
1111
10
8
7
12
12
11
11
109
.
Agreeable Sheep : Parts 1 Back
-
7/31/2019 1279370006886
6/9
The Agreeable Sheep : Parts 2 Rob Ives / Flying Pig 2007
TopfrontTop front
4
44
4
17
14
13
14
13
2 6.3
1
Cam Follower
Hea
d
Body
BodyInner
-
7/31/2019 1279370006886
7/9
4
44
4
5
17
2
11
6
1
8
32
1
Agreeable Sheep : Parts 2 Back
-
7/31/2019 1279370006886
8/9
The Agreeable Sheep : Parts 3 Rob Ives / Flying Pig 2007
Box
Back
Cam Shaft
Neck
Push-rod
26 25
27
27
28
24
23
23
24
24
24
29
29
5
6.
19
21
23
23
24
24
24
24
22
Not one to stand out of the crowd, our woolly
friend agrees with everything you say...
"Is this a good colour scheme?" "Yes!"
"Would you like to go for a walk?" "Yes!"
"Are you having a good time?" "Yes!"
"Does my bum look big in this?" ...probably best
not to ask.
With this agreeable model you need never get a
second opinion again.
Baa baa baa!
Rob Ives / Flying Pig 2007
Handle
Washer
Cam
www.flying-pig.co.uk
-
7/31/2019 1279370006886
9/9
19
22
20
29
29
25 26
28
27
27
20
30 3
0
Agreeable Sheep : Parts 3 Back