Download - 2 - Kitchen and Utility Rooms
-
7/31/2019 2 - Kitchen and Utility Rooms
1/24
36
Ummm something smells
nice
The kitchen is often the focal point of the
home. Its the place where we cook,
wash up, eat and often entertain. Its also
a source of heat, steam, and odours.
Cooking smells can wet your appetite but
unchecked they drift and linger
throughout the house. Condensation can
damage furnishings and too much heat
can be a real problem in modern well-
insulated dwellings.
Properly ventilated, the kitchen can
remain a fresh environment in which to
work and live.
Utility rooms are often a mix of heat from
laundry equipment and VOCs from
cleaning materials. They are subject to a
variety of uses from clothes drying to
washing the dog! Ventilation effectively
extracts this water vapour and odours.
For installations that fall within the scope
of Building Regulations the unit
ventilation extract requirements are
Kitchens 60l/s (30l/s with a cooker hood)
and Utility rooms 30l/s. If the room does
not have an opening window then a fan
with a built in timer should be selected.
This will continue to run for at least 15
minutes after the room has been vacated.
Older properties present a different
challenge. With generally larger rooms,
higher ceilings but poorer insulation, the
effects of condensation are often more
obvious. Here, a better method of
selecting a fan is based on room volume
multiplied by air change.
Domestic kitchens 15-20 ach
Utility rooms 15-20 ach
For kitchen canopies a speed selectable
model with a high speed of over 450m3/h
is often necessary to capture the heat
and steam from a hob with four pans. For
island installations this extract figure
needs to be doubled.
The extract point should always be
positioned to capture water vapour and
odours at source. With the exception of
kitchen canopies, it should be located as
high as possible and provide a flow
across the room with air replacement
usually coming from the doorway.
Axial fans are suitable for through the wall
or window fitting in most homes. For high-
rise and exposed (e.g. coastal) locations,
centrifugal fans will cope better with gusty
conditions. Centrifugal and mixed flow
units have a better pressure characteristic,
which makes them more suitable where a
ducted solution is required.
If there is a fuel burning appliance in the
room, ensure that there is adequate airreplacement for both the fuel burning
appliance and the fan.
In a kitchen, the right position will usually
be an external wall or a window, but keep
away from direct heat sources over 40C,
such as an eye level grill.
And dont forget the fan needs to be
accessible for regular cleaning. Ventilation,
working effectively, will pick airborne
particles, which would otherwise deposit to
your dcor.
Kitchens andUtility Rooms
-
7/31/2019 2 - Kitchen and Utility Rooms
2/24
37www.xpelair.co.uk Kitch
ens
Kitchens
Page Number 38 40 42 40 44 46 48-51 52 54 54
Fan Type Axial Axial Axial Axial Centrifugal Centrifugal Centrifugal Flat ducting Axial Centrifugal
Positioning Wall Window Window Window Wall Wall Wall n/a Celing Ceiling
/ Wall / Wall / Wall
Max extract rate 218 266 284 549 245-250 216 850 n/a 329 286
(m3/h)Duct dia (mm) 150 n/a n/a n/a 100 100 125 w204 x h60 200 102/150
Carbonlite
For Domestic Sensors, Switches & Accessories see pages 56 - 59
GX6 GXC9GX6 EC2DX400/
CF40 Canopies CX10Profile 60 CMFSL150/
SG150HP
GX6/GXC6
NEWNEW NEW
CF20/40T(UltraCV)
-
7/31/2019 2 - Kitchen and Utility Rooms
3/24
Type: Axial extract fan withwafer thin grille
Application: Kitchens and utility
rooms
Control options: Pullcord, timer &humidistat
Legislation: Conforms to BuildingRegulations Part F1
Hole diameter: 150mm
Key features
Xpelair Slimline SL150 & SG150HP
Wafer thin axial fans
38
SL150 SL150P SL150T SL150HT SL150HP SG150HP
Reference number 91229AW 91230AW 92361AW 91231AW 91496AW 92349AW
Remote switch (supplied separately)
Integral pullcord
Integral timer (adjustable up to 15 mins) * *Integral humidity sensor (45-99% RH) ** **Extract performance (FID, m3/h) 218 218 218 218 218 218
Extract performance (FID, l/s) 60 60 60 60 60 60
Sound pressure level (dB(A)@3m) 43 43 43 43 43 43
Electrical power rating (W) 35 35 35 35 35 38
IP rating IPX4 IPX4 IPX4 IPX4 IPX4 IPX2
Weight (kg) 0.9 0.9 0.9 0.9 0.9 1.5
Guarantee (years, UK) 2 2 2 2 2 2* Adjustable upto 0-35 mins ** 50-80% RH
Select the right product for your application
Meet the new generation of Xpelair
Slimline SL150 fans, with wall hugging
wafer-thin grilles designed for modern
living. They are white in colour and are
ideal for utility rooms and other small
rooms. With an internal projection of
only 15mm (SG150HP 58mm), the
150mm Xpelair Slimline unit is one of
the lowest profile fans available.
Humidistat models are available for
shower rooms and heavily used
bathroom applications. Ordering is
straight-forward: simply select the sizeand control option required, then add
the appropriate window or wall kit
(SG150HP comes with a window kit).
But the Slimline range doesnt just
have a pretty face, installation is simple
too. All Slimline models have two
adjustable QuickClamp fixings which
make traditional wall plug and screw
fixings a thing of the past (excluding
the SG150HP).
The IPX4 rated units fully meet the
requirements of the Building
Regulations for bathrooms, toilets and
kitchens and the IP requirements for
zone 1 and zone 2 as defined by the
IEE Wiring Regulations (16th Edition)
BS7671:2001. All models are suitable
for a supply voltage of 220-230V 50Hz
and ambient temperatures up to 40C.
The Range
Wafer thin grille
NEW
SG150HPSL150
SG150HP with silent action electrothermoshutter cassette and external grille
Excludes the SG150HP
-
7/31/2019 2 - Kitchen and Utility Rooms
4/24
Wall Mounting
Hole diameter: 157mm (SL150)
ControllersModels
SL150Ref. 91229AW Single speed axial fan Operated by a remote switch or sensor,
usually a lighting circuit
Built in backdraught shutter Colour: White
SL150PRef. 91230AW Single speed axial fan with pullcord Operated by integral On/Off pullcord switch Built in backdraught shutter Colour: White
SL150TRef. 92361AW Single speed axial fan with timer Timer triggered by remote switch-usually the
lighting circuit Timer variable from 3-15mins Colour: White
SL150HTRef. 91231AW
Single speed axial fan with humidistat andoverrun timer
Built in adjustable humidistat
Integrated overrun timer eliminatesnuisance tripping
Timer variable from 3-15mins Built in backdraught shutter Colour: White
SL150HPRef. 91496AW Speed increases automatically as humidity
increases Integral On/Off pullcord gives full speed
override Built in backdraught shutter Colour: White
SG150HPRef. 92349AW Speed increases automatically as humidity
increases Integral On/Off pullcord gives full speed
manual override Built in backdraught shutter Colour: White Can be window mounted, and has a built in
silent action electro-thermo shutter cassette,and an external grille
Passive Infrared Sensor XPIRA
Ref. 21871AA
Activates fan via body movement
Ideal for infrequently used public spaces
Built in timer to prevent nuisance tripping
Remote Time Controller DT20B
Ref. 21850AW
User adjustable run-on timer (2-20mins)
Installation and Accessories
Dimensions (mm)Performance
39
XpelairSlimlineSL150
&SG150HP
|Wa
ferthinaxialfans
SL150 Range
Typical Specifications on page 164.
Wiring Diagrams on page 182.
Remote Sensor on page 56.
Window MountingCeiling Mounting
Hole diameter: 157mm (SL150) Hole diameter: 150mm (SL150)
Ducted Applications
Hole diameter: 157mm (SL150)
Duct diameter: 150mm (SL150)
Installation Accessories
SL150 wall kit SLWK
Ref. 91233AW
Installation Accessories
Flexible ducting FD150
Ref. 89671AA
Installation Accessories
SL150 window kit*
Ref. 91235AW
* Backdraught shutter must be
removed
Installation Accessories
Flexible ducting FD150
Ref. 89671AA
SG150HP
-
7/31/2019 2 - Kitchen and Utility Rooms
5/24
Application: Domestic kitchens &utility rooms forwall or window mount
Control options: Pullcord
TimerHumidistat
Legislation: Conforms to Building
Regulations Part F1
Hole diameter: 203mm (GX6/C6 wall)
184mm (GX6/C6 window)266mm (GXC9 wall)257mm (GXC9 window)
Xpelair GX6, GXC6 & GXC9
Kitchen axial fans
40
GX6 GX6T GX6HT GX6HT2 GXC6 GXC6T GXC6SC GXC9
Reference number 90800AW 90812AW 90814AW 90863AW 90850AW 90861AW 91142AW 89995AW
Integral electrothermal shutter
Integral pullcord shutter
Integral adjustable run-on timer (2 to 20 mins)
Humidity sensor (50-90% RH)
Speeds 1 1 1 2 1 1 variable 1
Extract performance (FID, m3/h) high 266 266 266 266 266 266 260 549
low 222 83
Extract performance (FID, l/s) high 74 74 74 74 74 74 72 153
low 62 23
Sound pressure level (dB(A)@3m) high 37 37 37 37 37 37 34 44
low 34 25
Electrical power rating (W) 30 30 30 30 30 30 30 32
Hole diameter (mm) 184 184 184 184 184 184 184 257
Hole diameter with wall liner (mm) 203 203 203 203 203 203 203 266*
Weight (kg) 1.9 1.9 1.9 1.9 1.9 1.9 1.9 3.9Guarantee (years, UK) 3 3 3 3 3 3 3 3
*for wall kit WK9/8, increase to 330mm for WK9/11
Select the right product for your application
For over forty years the Xpelair GX
series has remained the specifiers
classic solution to domestic ventilation
applications. Todays 5th generation of
GX units remains in tune with the times.
They retain their hallmark rugged
reliability and styling, and the range has
been expanded to include innovations
for a range of specialist tasks.
Now supplied with longer ladder strips.
Xpelair GX models are purpose
designed for use in domestic kitchens,
utility rooms, large bathrooms andcommercial applications such as small
offices. They are highly efficient axial
fans suitable for direct ventilation to the
outside. Window, wall or panel
mounting options are available using
the universal mounting kit provided.
All have a stylish white housing with
integrated safety finger guard and
silent shutter operation using an
electro-thermal actuator (except GXC6
where it is pullcord operated).
GXC models have an integral pullcord
actuator. Timer and humidistat versions
are also available along with multi-speed
models. GXC6SC is also suitable for
professional speed adjustment where
there is a fuel burning appliance in the
room. A trickle ventilation facility is
available for background ventilation
when not in use.
Xpelair GX and GXC6 fans conform to
Building Regulations mechanical
ventilation for kitchens. They are
designed for easy cleaning andmaintenance, are BEAB approved and
are rated as Class 1 earthed appliance.
For larger kitchens, especially in older
properties, a larger volume of air flow
may be appropriate in order to achieve
the recommended air change rates.
For these applications the GXC9 may
be more appropriate. Refer to the
commercial ventilation section for
more details on larger wall and
window models.
The Range
New longer ladder strips
Key features
-
7/31/2019 2 - Kitchen and Utility Rooms
6/24
Timer and Boost Switch TBSRef. 90202AW Switch 1: switches between humidity
control and manual operation Switch 2: High-low speed Suitable for use with GXC6HT2
Remote Humidistat XRHRef. 21856AW
Stand alone humidistat switches fan On/Offwhen RH reaches pre-set levels
Complete with pullcord override switch Suitable for use with GX6
Remote Time Controller DT20BRef. 21850AW Provides continued ventilation run-on
period after light has been switched Off User adjustable run on timer (2-20 mins)
Passive Infrared Sensor XPIRARef. 21871AA Activates fan via body movement. Ideal for
infrequently used public spaces. Built in timer to prevent nuisance tripping
Suitable for use with GX6
Models
Performance
GX6/GXC6
Range
GXC9
Range
GX6Ref. 90800AW Single speed extract fan Operated by remote switch or sensor
(not supplied)
GX6TRef. 90812AW Single speed extract fan Integral run on timer (adjustable from
2-20mins) operated by lighting circuit
GX6HTRef. 90814AW Single speed extract fan Integral automatic humidistat operation
adjustable between 50-90% RH Integral run-on timer operated by the
lighting circuit Timer adjustable from 2-20mins
GX6HT2Ref. 90863AW Two speeds and humidistat or manual
control selectable using an Xpelair TBS
control (not supplied) Silent electrothermal shutter Automatic humidistat operation adjustable
between 50-90% RH Integral run-on timer operated by room
lighting circuit Timer adjustable from 2-20mins
GXC6Ref. 90850AW Single speed extract fan Integral pullcord switches fan On and
opens shutter
GXC6TRef. 90861AW Single speed extract fan Integral pullcord switches fan on and
opens electrothermal shutter Pullcord off action actuates timer
overrun (adjustable from 2-20mins) thencloses shutter
GXC6SCRef. 91142AW Extract fan with adjustable speed control Integral pullcord switches fan On and
opens shutter Built-in control allows performance to be set
to suit room size or use Also suitable for professional speed
adjustment where there is a fuel burningappliance in the room
GXC9 features over the GX6Ref. 89995AW Nine inch high performance extract
axial flow ventilation unit As GX6 with integral pullcord Integral pullcord turns fan On and
operates shutter
Dimensions (mm)
41
XpelairGX6,GXC6&G
XC9
|Kitchenaxialfans
Typical Specifications on page 164.
Wiring Diagrams on page 183.
Remote Sensors on page 56.
Installation and Accessories
Dimensions (mm)Model A B C D E F G H J KGX6, GXC6 226 210 119 107 109 101 184/203 32 4-35 112GXC9 312 294 165 147 147 147 257/266 32 4-35 117
GX6/GXC6 GXC9GXC9GX6/GXC6
Controllers
Window MountingWall Mounting
Hole diameter: 203mm
Installation Accessories
Wall Kit 200mm Ref. 89369AAWall Kit 280mm Ref. 89370AA
Longer ladder strips* Ref. 89382AAProtective Wall Grille PG6
Ref. 89375AA
Hole diameter: 184mm
Installation Accessories
Longer ladder strips*
Ref. 89382AA
Wall Mounting
Hole diameter: 266mm
Installation Accessories
Wall Kit 200mm Ref. 89371AAWall Kit 280mm Ref. 89372AA
Longer ladder strips* Ref. 89382AAProtective Wall Grille PG9
Ref. 89376AA
Window Mounting
Hole diameter: 257mm
Installation Accessories
Longer wall ladder strips*
Length 508mm
Ref. 89382AA*for walls/windows over 45mm thick,longer ladder strips are required
(see page 91)For exposed applications such as coastal use RX6, RX9 See page 94
-
7/31/2019 2 - Kitchen and Utility Rooms
7/24
42
Type: Energy efficient UltraECaxial Window / Wallfan with built inbackdraft shutter.
Application: Intermittent ventilationin kitchens, utility rooms.
Control options: 1 speed selectable oninstallation or 2 speedswith COS switch
Legislation: Conforms to BuildingRegulations Part F1 &
Scottish BuildingRegulations forintermittent use inkitchens and utilityrooms.
Hole diameter: Window: 184mmWall: 203 mm
Key features
Xpelair GX6 EC2 & GXC6 EC2
Kitchen and Utility room axial fans with UltraEC technology
The new Xpelair GX6 range with
UltraEC technology - Energy efficient
and long lasting.
GX6 EC2 and GXC6 EC2 are
designed with installer selectable
settings to satisfy Part F1 installed
performances for intermittent
ventilation in kitchens or utility rooms.
Window or panel installation uses a
ladder strip and external grille fitted with
a gasket to provide a seal to the
mounting surface. For wall applicationsan additional wall sleeve assembly is
recommended.
Both models have a stylish white
housing with integral safety finger
guard; GX6 has a silent backdraft
shutter operation using an
electrothermal actuator; GXC6 shutter
is pullcord operated.
GX6 EC2 and GXC6 EC2 models
feature UltraEC offering reduced
energy use, a choice of installed
performances and longer life than a
conventional AC motor. For this reason
Xpelair offers a 5 year UK only
guarantee.
The Range
GX6 EC2 GXC6 EC2
Select the right product for your application
Reference Number 92294AW 92295AWLonglife UltraEC motor Yes YesSelectable speeds at installation 284m3/h = 10.6W 284m3/h = 7.9W
144m3/h = 7.1W 144m3/h = 3.4WElectric Power rating (W) 10.6 7.9Sound pressure level (dB(A) @3m) 30.3 30.3Integral electro-thermal shutter YesIntegral pullcord shutter YesHole diameter in window (mm) 184 184Hole diameter using wall kit (mm) 203 203Weight (kg) 1.9 1.9Guarantee (Years UK) 5 5
-
7/31/2019 2 - Kitchen and Utility Rooms
8/24
43
XpelairGX6EC2&GX
C6EC2
|KitchenandUtilityroom
axialfan
swithUltraECtechnology
Models
GX6 EC2Ref. 92294AW
Extract fan with two installed performance options: installer selectedfor Kitchens and Utility rooms
Operated by remote switch (not supplied)
2 speed with COS
Energy saving Longlife UltraEC external rotor motor with maintenancefree sealed for life bearings and thermal overload protection
Integral safety finger guard
Integral mechanically operated louvred backdraft shutter with electro-thermal actuator
Inner grille and shutter cassette can be removed for easy cleaning
Double insulated
GXC6 EC2Ref. 92295AW
Extract fan with two installed performance options: installer selectedfor Kitchens and Utility rooms
Built-in pullcord On-Off operation
2 speed with COS
Energy saving Longlife UltraEC external rotor motor with maintenancefree sealed for life bearings and thermal overload protection
Integral safety finger guard
Integral mechanically operated louvred backdraft shutter with pullcordOn-Off actuator
Inner grille and shutter cassette can be removed for easy cleaning
Double insulated
Performance
Dimensions (mm)
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300
Flow rate in m3/h
60
55
50
45
40
35
30
25
20
15
10
5
0Low SpeedHigh Speed
Static
Pressure
in
Pa
Dimensions (mm)A B C D E F G H J K226 210 119 107 109 101 184/203 32 4-25 112
Installation and Accessories
GX6/GXC6 EC2 GX6/GXC6 EC2
Window Mounting
Hole diameter: 203mm
Installation Accessories
Wall Kit 200mm Ref. 89369AAWall Kit 280mm Ref. 89370AALonger ladder strips* Ref. 89382AAProtective Wall Grille PG6
Ref. 89375AA
Wall Mounting
Hole diameter: 184mm
Installation Accessories
Longer ladder strips*
Ref. 89382AA
*for walls/windows over 45mm thick, longerladder strips are required
Typical Specifications on page 164.
Wiring Diagrams on page 183.
Domestic Accessories on page 56.
-
7/31/2019 2 - Kitchen and Utility Rooms
9/24
Application: Domestic kitchens,utility rooms and largerbathrooms; commercialbathroom, small officesand public toilets.Suitable for surface andfloor, wall and ceilingmounting
Control options: Pullcord, timer andhumidistat
Legislation: Conforms to BuildingRegulations Part F1
Hole diameter: 117mm
Key features
Xpelair Premier DX400 & CF40
Centrifugal extract and condensation control fans
Kitchen ventilation has never looked so
good. Since its launch, Premier has
taken the ventilation market by storm.
DX400 extract and CF40 condensation
control fans are no exception. These
pressure developing centrifugal fans
are sleekly styled and are ideally suited
for use in kitchens, utility rooms and
larger bathrooms and toilets and
individual offices.
They can be surface or flush mounted
in walls and ceilings using the
universal mounting accessories
provided, and include a back draught
shutter and outlet grille. Both models
have their inlet discreetly concealed
behind a stylish white front cover. This
cover is held in position by clips for
easy removal for cleaning.
Control options include integral
pullcord and timer. Models with an
integral humidistat offer automatic
control. CF40TD features a delay start
quick visit facility preventing the fan
from coming on should the light be
switched on and then off within 2
minutes.
All models are IPX5 rated and BEAB
approved. They are all suitable for 220-
240V 50Hz mains operation and
feature external rotor motors with
integral balanced impellers, sealed for
life maintenance free bearings and
safety thermal cut out protection.
Optional filter is available see page 57.
The Range
DX400 DX400T DX400PC DX400RS CF40 CF40TD CF40RSTD
Select the right product for your application
Reference number 91083AW 91084AW 91100AW 91085AW 91086AW 91087AW 91088AWRemote switch (supplied separately) Remote switch (supplied) Integral pullcord Integral adjustable run-on timer (30s to 20 mins) Humidity sensor (50-90% RH)
Quick visit facility (2 minutes) Speeds 2 3 3 3 5 5 5Trickle ventilation facility Extract performance (FID, m3/h) boost 250 250 250
speed 3 174 174 174speed 2 245 245 245 245 143 143 143speed 1 143 143 143 143 90 90 90trickle 61 61 61 61 61 61
Extract performance (FID, l/s) boost 69 69 69speed 3 48 48 48speed 2 68 68 68 68 40 40 40speed 1 40 40 40 40 25 25 25trickle 17 17 17 17 17 17
Sound pressure level (dB(A)@3m) boost 55 55 55speed 3 46 46 46speed 2 55 55 55 55 40 40 40speed 1 42 42 42 42 33 33 33trickle 27 27 27 27 27 27
Electrical power rating (W) 78 78 78 78 77 77 77Hole diameter 115 115 115 115 115 115 115
IP rating IPX5 IPX5 IPX5 IPX5 IPX5 IPX5 IPX5Weight (kg) 3 3 3 3 3 3 3Guarantee (years, UK) 3 3 3 3 3 3 3
44
-
7/31/2019 2 - Kitchen and Utility Rooms
10/24
Typical Specifications on page 165.
Wiring Diagrams on page 183.
Remote Sensors on page 56.
Controllers
Performance
Models
Premier DX400Ref. 91083AW Two speed centrifugal fan Pre-select speed to suit application Alternatively use optional COS switch to
change between speeds and On/Off
Includes external wall grille
Premier DX400TRef. 91084AW Centrifugal fan with timer Timer is typically connected to a lighting circuit Built in run-on period after the light has
been switched Off, user adjustable from30s-20min
Fan operates at full speed when light is On,then operates at reduced speed during run-onand the switches to either Trickle or Off(installer selectable)
QuickVisit delay feature prevents the fanfrom running should the light be switchedOn/Off again within two minutes
Fan running status lights Includes external wall grille
Premier DX400PC
Ref. 91100AW High, Low, On/Off with tricklevent operated
by integral 3 position pullcord switch Fan running status lights Includes external wall grille
Premier DX400RSRef. 91085AW Two speed centrifugal fan Pre-select speed to suit application Alternatively use optional COS switch to
change between speeds and On/Off Trickle vent option is activated by a preset
switch on the unit
Fan running status lights Includes external wall grille
Premier CF40Ref. 91086AW Condensation Control Range with
humidistat Automatic operation through integral
humidity sensor Pullcord selects High, Low, Off or Trickle
Premier CF40TDRef. 91807AW Automatic operation through integral
humidistat Pullcord selects High, Low, Off or Trickle QuickVisit delay feature prevents the fan
from running should the light be switchedOn/Off again within two minutes
Fan running status lights Includes external wall grille
Premier CF40RSTDRef. 91088AW Automatic operation through integral humidistat MOS remote switch (supplied) selects high
or low speed and can switch the unit Off (orto tricklevent). Built in humidity control run on period User adjustable from 30sec-20min Fan running status lights Includes external wall grille
Note: For kitchen applications a grease f ilterPDXGF is recommended Ref. 91145AA
Installation and Accessories
Dimensions (mm)
XpelairPremierDX400
andCF40
|Centrifugalextractandcond
ensationcontrolfans
DX400/CF40 RangeDX400 Range CF40 Range
Wall Mounting
Hole diameter: 117mmDuct ing size: 100mm
Installation Accessories
Easy fit kit EFT Ref. 90427AAWall Tube WD100 Ref. 89543AA
Ducted Applications Ventilation Shaft Mounting
Hole diameter: 117mmDucting size: 100mm
Ceiling Mounting
Hole diameter: 117mmDucting size: 100mm
Installation Accessories
Flat ducting XFP see Profile 60Flexible ducting FD100 Ref. 89910AACondensation trap XCT100 Ref. 89749AAVent cowl VC10 Ref. 89531AACeiling mounting kit XCMK Ref. 90066AA
Manual Override Switch MOS
Ref. 90199AW
Switch 1 controls the high/low speed levels and
Switch 2 controls On/Off and the tricklevent option
Change Over Switch COS
Ref. 90108AW
Used to select between high and low speed
operation
Remote Humidistat XRH
Ref. 21856AW
Stand alone humidistat switches fan On/Off
when RH reaches pre-set levels. Complete
with pullcord override switch
Remote Time Controller DT20B
Ref. 21850AW User adjustable run-on timer (2-20mins)
Passive Infrared Sensor XPIRA
Ref. 21871AA
Activates fan via body movement
Ideal for infrequently used public spaces
Built in timer to prevent nuisance tripping
45
100 Spigot
100
-
7/31/2019 2 - Kitchen and Utility Rooms
11/24
46
NEW
Xpelair Premier CF20/40T CV
Centrifugal extract and condensation control fans
Type: Constant VolumeUltraEC Centrifugalextract fan
Application: Intermittent ventilation,Humidity controlledintermittent ventilation,Decentralisedventilation
Control options: Installer selectablehumidistat, timer andpullcord override
Legislation: Conforms to BuildingRegulations Part F1
Hole diameter: 115mm
The Premier CF20/40T CV modelfeatures UltraEC technology offeringreduced energy use, a choice ofinstalled performances and a longerlife than a conventional AC motor.
The fan is designed to comply with therequirements of Part F1 to provideIntermittent Ventilation in Kitchens,Utility rooms, Bathrooms and SanitaryRooms, Humidity Controlledintermittent Ventilation + manual over-ride in Kitchens and Bathrooms,Intermittent Ventilation in Internal roomsand Decentralised Continuous
Ventilation in Kitchens, Utility Rooms,Bathrooms and Sanitary Rooms.
Performance is set at installation via aseries of internal dip switches.The Constant Volume nature of the fanmeans that performance remains
constant irrespective of the installedcondition up to a system pressure of100Pa. The fan can be surface orflush mounted in walls and ceilingsusing the universal mountingaccessories provided.
The fan is provided with a backdraught shutter for intermittentapplications. It is not to be fitted for thelower velocity continuous decentralisedapplications. Control options includeintegral Humidistat, pullcord over-ride,run on timer and 'quick visit' delaystart facility. Xpelair offers a 5 year UK
only guarantee.
The RangeKey features
Speed Settings Extract Performance Noise dB(A) @ 3m Power (W)
Intermittent Ventilation l/s m3/h
Kitchen 60l/s 216m3/h via integral pullcord 55.8 31W
Utility 30l/s 108m3/h via integral pullcord 39.9 8.4W
Bathroom 15l/s 54m3/h via integral pullcord 22.7 4.9W
Sanitary Room 6l/s 22m3/h via remote switch (not supplied) 20.8 4.2W
Humidity Controlled intermittent Ventilation
+ manual over-ride
Kitchen 60l/s 216m3/h Off. Humidity. pullcord 55.8 31W
Bathroom 15l/s 108m3/h 216m3/h Off. Humidity. pullcord 22.7 4.9W
Intermittent Ventilation - Internal Rooms
Kitchen 60l/s 216m3/h + 15min over-run timer triggered via light switch 55.8 31W
Utility 60l/s 216m3/h + 15min over-run timer triggered via light switch 55.8 31W
Bathroom 15l/s 54m3/h + 15min over-run timer triggered via light switch 22.7 4.9W
Sanitary Room 15l/s 54m3/h + 15min over-run timer triggered via light switch 22.7 4.9W
Decentralised Continuous Ventilation
Kitchen 13l/s 20.8 4.6W
Utility 8l/s 21.4 4.4W
Bathroom 8l/s 21.4 4.4W
Sanitary Room 6l/s 20.8 4.2W*Measured with 300mm of ducting and wall grille fitted on the outlet side. Note: As this is a constant volume product, as the back pressure on the system increases so the motor
increases speed to maintain airflow. This has the effect of increasing motor input power. Product is rated at 230V, 50/60Hz, single phase.
At Zero Static Pressure*
Select the right settingfor your application
-
7/31/2019 2 - Kitchen and Utility Rooms
12/24
XpelairPremierCF20/40TCV
|Centrifuga
lextractandcondensa
tioncontrolfans
47
Performance
Dimensions (mm)
Premier CF20/40T CV
Ref.92293AW
Constant Volume centrifugal fan with speed
selectable at installation by means of dip
switches.
UltraEC longlife low energy motor
External rotor motor with integral balanced
impellers, sealed for life maintenance free
bearings and safety thermal cut
out protection
Fan maintains selected extract volume
irrespective of system resistance up
to 100Pa
Built in Humidistat controlled intermittent
ventilation option
Built in timer controlled intermittent ventilation
option for internal rooms
Run on period of 20 sec-20min
(installer adjustable) after light has beenswitched Off. Factory set at 15 min in
compliance with Part F1
'Quick visit' feature prevents the fan
coming on if the room is occupied for
less than two minutes
Includes external wall grille and fan backdraft
shutter for intermittent applications
Typical Specifications on page 161.
Wiring Diagrams on page 181.
Remote Sensors on page 56.
Models
Installation and Accessories
Wall Mounting
Hole diameter: 117mmDuct ing size: 100mm
Installation Accessories
Easy fit kit EFT Ref. 90427AAWall Tube WD100 Ref. 89543AA
Ducted Applications Ventilation Shaft Mounting
Hole diameter: 117mmDucting size: 100mm
Ceiling Mounting
Hole diameter: 117mmDucting size: 100mm
Installation Accessories
Flat ducting XFP see Profile 60Flexible ducting FD100 Ref. 89910AACondensation trap XCT100 Ref. 89749AAVent cowl VC10 Ref. 89531AACeiling mounting kit XCMK Ref. 90066AA
-
7/31/2019 2 - Kitchen and Utility Rooms
13/24
Xpelair Nouvelle Cuisine
Kitchen canopies
Type: Kitchen canopy
Application: Domestic kitchens
Control options: Integral
Legislation: Conforms to BuildingRegulations Part F1
Key features
For many households the kitchen is the
busiest room in the home. As well as an
area for cooking, it is often the main focal
point for family and guests.
But with cooking odours, steam and
condensation continually building up,
keeping the kitchen fresh and pleasant is
a constant problem. The Nouvelle
Cuisine range of kitchen canopies is
elegantly designed to suit every kitchen
design and budget.
Using powerful extraction and filters every
model in the range will keep rooms free of
steam and odour leaving behind a fresh
and comfortable environment.
Crafted from high quality materials such as
stainless steel and glass and equipped with
push button controls and built-in spotlights,
the Nouvelle Cuisine kitchen canopies are
a stylish addition to any kitchen.
With wall fix, island and built-in models
available, the Nouvelle Cuisine range
provides flexibility and choice for the
perfect fit, practicality and ease of use.
The Range
90 Curved
Ref. 91202AW
Description: 90cm Curved Glass Canopy
Finish: Stainless Steel and Glass
Duct size: 125mm
Features / Specification
90cm Curved Glass Canopy
3 speed levels
Stainless steel finish
Recirculation or extraction
Maximum extraction rate 480m3/h
Electronic touch control
200W motor
Twin 50W halogen spotlights
Aluminium grease filter Optional carbon filter system
Dimensions
Models
60 70 90 100 110
Reference number 91204AW 91205AW 91206AW 91207AW 91208AW
Finish stainless steel stainless steel stainless steel stainless steel stainless steel
Size (mm) w600 x h750 w700 x h750 w900 x h750 w1000 x h750 w1100 x h750
Splashbacks
90 Curved
Reference number 91202AWFreestanding Max extraction performance (l/s) 133Sound pressure level* (dB(A)) 39Motor rating (W) 200Speeds 3Recirculation Extraction Duct size (mm) 125No. grease filters 1Grease filter type aluminiumBuilt-in lighting 2 x 50WMaximum width (mm) 900Finish stainless steel
& glassReplacement filters 41834SK*at low speed
48
Typical Specifications on page 165.
Wiring Diagrams on page 183.
90 Curved
-
7/31/2019 2 - Kitchen and Utility Rooms
14/24
XpelairNouvelleCuisi
ne
|Kitchencanopies
Dimensions (mm)
90 Island
Ref. 91203AW
Description: 90cm Island Glass Canopy
Finish: Stainless Steel and Glass
Duct size: 125mm
Features / Specification
90cm Island Glass Canopy
3 speed levels
Stainless steel finish
Recirculation or extraction
Maximum extraction rate 851m3/h
Electronic touch control
240W motor
Four 50W halogen spotlights
Aluminium grease filter Optional carbon filter system
60 / 90 Flat
Ref. 91200AW / Ref. 91201AW
Description: 60/90cm Flat Glass Canopies
Finish: Stainless Steel and Glass
Duct size: 125mm
Features / Specification
60/90cm Flat Glass Canopies
3 speed levels
Stainless steel finish
Recirculation or extraction
Maximum extraction rate 480m3/h
Electronic touch control
200W motor
Twin 50W halogen spotlights
Aluminium grease filter Optional carbon filter system
Models
70 / 90 Box
Ref. 91198AW / Ref. 91199AW
Description: 70/90cm Box Canopies
Finish: Stainless Steel
Duct size: 125mm
Features / Specification
70/90cm Box Canopies
3 speed levels
Stainless steel finish
Recirculation or extraction
Maximum extraction rate 480m3/h
Push button control panel
200W motor
Built in twin lights
Twin aluminium grease filters Optional carbon filter system
* 70 Box = 700mm
90 Box = 900mm* 60 Flat = 600mm
90 Flat = 900mm
90 Island 60 Flat 90 Flat 70 Box 90 Box
91203AW 91200AW 91201AW 91198AW 91199AW
236 133 133 133 13344 39 39 39 39
240 200 200 200 2003 3 3 3 3
125 125 125 125 1251 1 1 2 3
aluminium aluminium aluminium aluminium aluminium4 x 50W 2 x 50W 2 x 50W 2 x 40W 2 x 40W
900 600 900 700 900stainless steel & glass stainless steel & glass stainless steel & glass stainless steel & glass stainless steel & glass
41834SK 41834SK 41834SK 41834SK 41834SK
49
60 / 90 Flat
90 Island
70 / 90 Box
-
7/31/2019 2 - Kitchen and Utility Rooms
15/24
Xpelair Nouvelle Cuisine
Kitchen canopies
* 60 Tonda = 600mm
90 Tonda = 900mm
* 60 Chimney = 600mm
90 Chimney = 900mm
Dimensions
60 / 90 Tonda
Ref. 91196AW / Ref. 91197AW
Description: 60/90cm Tonda Canopies
Finish: Stainless Steel
Duct size: 125mm
Features / Specification
60/90cm Tonda Canopies 3 speed levels Stainless steel finish
Recirculation or extraction Maximum extraction rate 480m3/h
Sliding control panel 200W motor Built in twin lights
Twin aluminium grease filters
Optional carbon filter system
60 / 90 Chimney
Ref. 91194AW / Ref. 91195AW
Description: 60/90cm Chimney Canopies
Finish: Stainless Steel
Duct size: 125mm
Features / Specification
60/90cm Chimney Canopies 3 speed levels
Stainless steel finish Recirculation or extraction Maximum extraction rate 480m3/h
Push button control panel 200W motor
Built in twin lights Twin aluminium grease filters
Optional carbon filter system
Models
Inset
Ref. 91192AW
Description: 60cm Inset Canopy
Colour: Silver
Duct size: 125mm
Features / Specification
60cm Inset Canopy 3 speed levels
Available in silver finish Recirculation or extraction Maximum extraction rate 229m3/h
Sliding control panel 140W motor
Built in twin lights Carbon filter system
Acrylic grease filter in metal grid casing
60 Tonda 90 Tonda 60 Chimney 90 Chimney Inset
Reference number 91196AW 91197AW 91194AW 91195AW 91192AWFreestanding Integrated Max extraction performance (l/s) 133 133 133 133 64Sound pressure level* (dB(A)) 39 39 39 39 55Motor rating (W) 200 200 200 200 140Speeds 3 3 3 3 3Recirculation Extraction Duct size (mm) 125 125 125 125 125No. grease filters 2 2 2 2 1Grease filter type aluminium aluminium aluminium aluminium acrylic filter in
metal casingBuilt-in lighting 2 x 40W 2 x 40W 2 x 40W 2 x 40W 2 x 40WMaximum width (mm) 600 900 600 900 525
Finish stainless steel stainless steel stainless steel stainless steel silverReplacement filters 41834SK 41834SK 41834SK 41834SK 41832SK*at low speed
50
Inset
Tonda
Chimney
-
7/31/2019 2 - Kitchen and Utility Rooms
16/24
XpelairNouvelleCuisi
ne
|Kitchencanopies
Dimensions (mm)
Integrated
Ref. 91193AW
Description: 60cm Integrated Canopy
Colour: Silver
Duct size: 125mm
Features / Specification
60cm Integrated Canopy
3 speed levels Available in silver finish
Recirculation or extraction Maximum extraction rate 480m3/h Sliding control panel
125W motor Built in twin lights
Metallic grease filter in aluminium grille
Optional carbon filter system
Standard
Ref. 91189AW - White
Ref. 91190AB - Brown
Description: 60cm Standard Canopy
Colour: White or Brown
Duct size: 125mm
Features / Specification
60cm Standard Canopy
3 speed levels Available in white or brown finish Recirculation or extraction
Maximum extraction rate 320m3/h Sliding control panel
125W motor Built in twin lights
Additional carbon filter system Acrylic grease filter in metal grid casing
Models
Standard Plus
Ref. 91191AW
Description: 60cm Standard Plus Canopy
Finish: Stainless Steel
Duct size: 125mm
Features / Specification
60cm Plus Canopy 3 speed levels Stainless steel finish
Recirculation or extraction Maximum extraction rate 200m3/h
Sliding control panel 125W motor Built in twin lights
Twin aluminium grease filters
Additional carbon filter system forrecirculation only
Integrated Standard Standard Standard Plus
Reference number 91193AW 91189AW 91190AB 91191AWFreestanding Integrated Max extraction performance (l/s) 97 56 56 56Sound pressure level* (dB(A)) 39 40 40 52Motor rating (W) 200 125 125 125Speeds 3 3 3 3Recirculation Extraction Duct size (mm) 125 125 125 125No. grease filters 1 1 1 2Grease filter type acrylic filter in metal casing acrylic filter in metal casing acrylic filter in metal casing aluminiumAdditional carbon filter system optional Built-in lighting 2 x 40W 2 x 40W 2 x 40W 2 x 40WMaximum width (mm) 600 600 600 600
Finish silver white brown stainless steelReplacement filters 41833SK 41834SK 41834SK 41832SK*at low speed
51
Standard
Integrated
Standard Plus
-
7/31/2019 2 - Kitchen and Utility Rooms
17/24
-
7/31/2019 2 - Kitchen and Utility Rooms
18/24
53
XpelairProfile60
|Flatductingsystem
Dimensions (mm)
Profile 60
Flat channel outer dimensions are
w204 x h60mm and fit into system
parts sockets.
Cross section: 11200mm2
Minimum space required forinstallation: w210 x h65mm
Product Product Ref Description Dimensions (mm) Spigot ID (mm) Ref.
FPD100 Flat ducting, 1 metre length 204 x 60 89755AA
FPD150 Flat ducting, 1.5 metre length 204 x 60 91188AA
FPA Horizontal bend adjustable 204 x 60 89750AA
FPG Wall outlet grille 204 x 60 89751AA
FPP100 Elbow / Plenum box 204 x 60 100 89752AA
FPP125 Elbow / Plenum box 204 x 60 125 91259AA
FPP150 Elbow / Plenum box 204 x 60 150 91483AA
FPV90 Vertical 90 bend 204 x 60 89753AA
FPH90 Horizontal 90 bend 204 x 60 89754AA
FPB Mounting bracket (boxed in 5s) 204 x 60 89756AA
FPC Coupling 204 x 60 89757AA
FPT T piece 204 x 60 90091AA
FPF Flexible ducting, 0.5m 204 x 60 91484AA
PFB Intumescent type fire break 204 x 60 91975AA
PRA Round to rectangular adaptor 204 x 60 125 91482AA
Profile 60 Flat Plastic Ducting - w204 x h60mm
Additional Accessories
Acoustic Airbrick XAAB Ref. 91166AA
Acoustic Airbrick XAABW with white grille
Ref. 91162AA
Acoustic Airbrick XAABB with brown grille
Ref. 91163AA
Acoustic Airbrick XAABC
with Cotswold stone grille Ref. 91164AA
Acoustic Airbrick XAABT
with terracotta grille Ref. 91165AA
Suitable for use adjacent to noise nuisanceareas including roads, railways and airports
Weighted Sound Reduction Index Rw BS ENISO717-1:1997 = 7
Ceiling Kit XCMK
Ref. 90066AA
Use with ceiling mounted ducted products
Complete with tube, rubber gasket and foam strip
Condensation Trap XCT100
Ref. 89749AA
For use with 100mm diameter ducting
Prevents condensed water running backtowards the fan in vertical PVCu ducted
applications Collected water must be piped away to a
convenient disposal point
20mm outlet
Fire Damper XFC100
Ref. 89843AA
Provides 1 hour fire check in either direction Can be mounted at any angle
For ducts, walls and ceilings. Should not befitted into flexible ducting. Wall or duct in whichXFC is fitted should have a rated fire integrity in
accordance with Building Regulations Part B
100mm Xflex FD100
Ref. 89663AA
Wire helix flexible ducting 3m length
Typical Specifications on page 165.
-
7/31/2019 2 - Kitchen and Utility Rooms
19/24
Type: Ceiling mounted axialand centrifugal fans
Application: Domestic kitchens,bathrooms and
shower rooms
Legislation: Conforms to BuildingRegulations Part F1
Hole diameter: 300mm (CX10)185sq (CMF171)
248sq (CMF241)273sq (CMF271)
Xpelair CX10 & CMF
Ceiling mounted fans
54
CX10 CMF171 CMF241 CMF271
Reference number 90209AB 89955AW 89956AW 89957AW
Remote switch (not supplied)
Extract performance (FID, m3/h) 329 63 146 286
Extract performance (FID, l/s) 91 18 41 79
Sound pressure level (dB(A)@3m) 44 38 41 41
Electrical power rating (W) 34 30 33 48
Hole diameter (mm) 300 185x185 248x248 273x273
Ducting size (mm) 200 102 102 150
Weight (kg) 1.8 2.7 3.8 6.9
Guarantee (years, UK) 3 3 3 3
Select the right product for your application
Where wall space is tight or at a
premium, fitting an extraction system
drawing air from the ceiling is the
convenient and secure solution. Whats
more, ducted ceiling extract systems
free you to position the unit for
maximum benefit.
Suitable for domestic kitchens, larger
utility rooms and power shower rooms.
Light commercial applications include
customer waiting areas, changing
rooms, payment and ticket kiosks,
smoking rooms, office kitchens,
storage rooms, small meeting rooms
and offices. Commercial applications
include pub bars, factories, schools
and shops.
Flush mounted, Xpelair CX10 and
CMF units have a white finish to blend
into the ceiling dcor.
Behind this neat fascia are efficient fan
units, which connect directly to Xflex
ductwork to exhaust to the outside.
The CX10 units are axial fans and the
CMF units are pressure developingcentrifugal fans.
In many commercial applications such
as kiosks, retail clothing changing
booths and copying rooms where heat
build up is a problem it may be
sufficient simply to dilute the air about
the ceiling.
The CX10 is especially suitable for
dilution applications and short duct
runs. CMF models are ideal for longer
ducted extract systems.
Shallow in depth, several models will fit
between the ceiling of the room andthe floor above. In many of these
applications it is good practice to
consider sensor control, operating
automatically and only when
necessary, saving energy.
All models are suitable for high
humidity applications and have an
unobtrusive flush design with finger-
guard protection. Lubricated for life
motors, with maintenance free bearings
and safety thermal overload protection
are standard across the range.
The RangeKey features
CX10
CMF
-
7/31/2019 2 - Kitchen and Utility Rooms
20/24
CX10
Ref. 90209AB
Single speed axial flush mounted extract
ceiling fan with stylish circular flush design.
Unit comes complete with integral finger-
guard and fly screen Lightweight two piece construction
Moulded pre-balanced axial bladed impeller
Suitable for steam and condensation
applications
Vertical spigot with 200mm diameter
connection
Operated by remote switch or sensor
(not supplied)
CMF 171 Ref. 89955AW
CMF 241 Ref. 89956AW
CMF 271 Ref. 89957AW
Flush mounted extract ceiling fans
High performance single speed centrifugal
pressure developing motor/fan/scrollassemblies
Stylish square grille design with integral
finger-guard
Lightweight two piece construction with
horizontal spigot outlet
Cassette design allows ducting to be
installed prior to the fan itself
Tip
In situations where there is a tight closing
bathroom or kitchen door, air circulation can
be prevented. To remedy the situation fit a
slimline air-grille in white (89529AA) or brown
(89530AA) in door thicknesses up to 35mm.
CX10 Range CMF Range
Installation and Accessories
Dimensions (mm)
CX10 CMF Range
Please be aware that fan performance will
be affected by the use of ducting, grilles
and shutters.
Termination Ducting Kit TDK8
Ref. 89384AA
For use with CX10
Roof space ducting kit from fan to soffit
board.
Comprised flexible ducting, exterior grille,
duct tie and fixings
2.5m duct length comprising 0.5m formed
rectangular and 2m of 200mm diameter
Grille dimensions 294 x 193mm
55
XpelairCX10&CMF|
Ceilingmountedfans
Typical Specifications on page 166.
Wiring Diagrams on page 183.
Remote Sensors on page 56.
Ceiling MountingCeiling Mounting
Hole diameter: 300mmDucting size: 200mm
Installation Accessories
Termination Ducting Kit TDK8Ref. 89384AA
Hole diameter: 185 x 185mm (CMF171)248 x 248mm (CMF241)273 x 273mm (CMF271)
Ducting size: 102mm (CMF171/241)150mm (CMF271)
ControllersPerformance
Models
Remote Humidistat XRH
Ref. 21856AW
Stand alone humidistat switches fan On/Off
when RH reaches pre-set levels. Complete
with pullcord override switch
Remote Time Controller DT20B
Ref. 21850AW
User adjustable run-on timer (2-20mins)
Passive Infrared Sensor XPIRA
Ref. 21871AA
Activates fan via body movement. Ideal for
infrequently used public spaces. Built in timer
to prevent nuisance tripping
Dimensions (mm)
Model A B C D E
CMF171 277 226 123 230 240
CMF241 343 260 133 290 319
CMF271 420 318 133 320 350
CMF RangeCX10
-
7/31/2019 2 - Kitchen and Utility Rooms
21/24
Xpelair Domestic Sensors & Switches
56
Remote Humidistat XRH
Ref. 21856AW
Automatically switches On when the
relative humidity reaches an adjustable
preset point and switches off when the
relative humidity drops
Pullcord override switch
Fan indicator light
Surface or recess mounting
Suitable for ambient temperatures up
to 40C
Supply voltage 220-240V 50Hz
Used with: Premier DX180, DX200, DX400,
DX100, XIL, CMF, CX10, GX6
w160 x h86 x d45 mm
LoVolt Remote Humidistat LVH
Ref. 21863AW
A 12V SELV LoVolt humidistat
Automatically switches On when the
relative humidity reaches an adjustable
pre set point and switches Off when the
relative humidity drops
Pullcord override switch
Fan indicator light
Surface or recess mounting
Suitable for ambient temperatures up
to 40C
Supply voltage 12V SELV
Used with: Premier LoVolt DX200,
LoVolt CF20, LoVolt DX100
w160 x h86 x d45 mm
Time delay unit DT20B
Ref. 21850AW
Connected to a switching circuit such as
a bathroom lighting
Provides adjustable run on time delay
after the light has been switched Off
Time adjustable up to 20 minutes
Surface or recess mounting
Suitable for ambient temperature up
to 40C
Supply voltage 200 - 240V 50Hz
Used with: Premier DX180, DX200, DX400,DX100, XIL, CMF, CX10, LoVolt DX100
w100 x h86 x d45 mm
Passive Infrared Sensor XPIRA
Ref. 21871AA
For indoor use
Automatically switches a fan on when
body movement is detected
Incorporates a delay timer
Supply voltage 220-240V 50Hz
Used with: Premier DX200, DX400, DX100,
CMF, CX10, GX6
w86 x h86mm
Change Over Switch COS
Ref. 90108AW
Used to select between high and low
speed operation
Surface or recess mounting
Used with: DX400, DX400T, DX400RS
w85 x h85mm
Manual Override Switch MOS
Ref. 90199AW
Switch 1:high/low speed
Switch2: On/Off (or Off/tricklevent
according to fan option selected)
Surface or recess mounting
Used with: Premier DX200 and Premier
DX400, DX400RS in conjunction with XRH
Remote Humidistat.
w85 x h85mm
Timer and Boost Switch TBS
Ref. 90202AW
Provides switching between humidity
control / manual operation
Provides selection of high / low extract speed
Surface or recess mounting
Used with: GX6HT2
w85 x h85mm
Air Quality Sensor AQS
Ref. 92097AW
Provides fully automatic control
Detects contaminants such as cigarette smoke,
body odours, toilet odours and cooking smells
Activates ventilation system when preset
threshold level is exceeded
Can control up to six fans and accessories
Integral timer adjustable from 3 - 30 mins LED status indicator
Surface or recess mounting
Supply voltage 220-240V 50Hz
w210 x h86 x d41mm
-
7/31/2019 2 - Kitchen and Utility Rooms
22/24
57
XpelairDomesticSensors,Switches&A
ccessories
Flexible Ducting Xflex FD
Dia Length
FD100 100mm 3m Ref. 89663AA
6m Ref. 89669AA
FD125 125mm 3m Ref. 89664AA
6m Ref. 89670AA
FD150 150mm 3m Ref. 89665AA
6m Ref. 89671AA
FD200 200mm 3m Ref. 89666AA
6m Ref. 89672AA
Glass fibre fabric on a PVC coated close
pitch steel wire helix. 54 minute fire
integrity from within as measured to BS
476:Part 20 - (1987)
Can be interlocked and sealed with duct
tape to form an airtight seal. Attached to
spigots using worm drive clips
Worm Drive Clips WDC
WDC5
Ref. 89684AA
Dia.100-125mm
WDC8
Ref. 89685AA
Dia. 150-200mm
For connection of flexible ducting to spigots
Supplied in packs of 10
Thermal Flexible Ducting Xflex TFD
Dia Length
TFD100 100mm 5m Ref. 89847AA
10m Ref. 91459AA
TFD125 125mm 5m Ref. 89848AA
10m Ref. 91460AA
TFD150 150mm 5m Ref. 89849AA
10m Ref. 91461AA
TFD200 200mm 5m Ref. 89850AA
10m Ref. 91462AA
Double skinned insulated aluminium
duct with high density fibreglass
insulation to minimise condensation
formulation
25 minute fire integrity from within as
measured to BS 476: Part 20 - (1987)
Can be interlocked and sealed with duct
tape to form an airtight seal
New Aluminium Flexible Ducting Xflex ALU
Dia Length
ALU100 100mm 10m Ref. 91435AA
ALU125 125mm 10m Ref. 91436AA
ALU150 150mm 10m Ref. 91437AA
ALU200 200mm 10m Ref. 91438AA
Tough foil construction on a high strength
wire helix
Over 40 minute fire rating BS 476:
Part 20 (1987)
Premier Grease Filter PDXGF
For Premier DX200 models
Ref. 90548AA
For Premier DX400 models
Ref. 91145AA
For Premier units in kitchen applications
Fits behind the inlet
Material: Self extinguishing black
polyester foam
100mm Wall Duct WD100
Ref. 89543AA
For bridging cavities or lining solid
exterior walls
Mortared into position
Used with: Premier DX200, CF20,
Premier DX400, CF40
The premier models above come complete
with external grille. Premier DX180 also
requires wall grille
Dia. 100mm
Length 300mm
Xpelair Domestic Accessories
www.xpelair.co.uk
-
7/31/2019 2 - Kitchen and Utility Rooms
23/24
Xpelair Domestic Accessories
58
Ceiling Kit XCMK
Ref. 90066AA
Allows a sealed ceiling mounting of
ducted products
Compete with ceiling adaptor tube
105.7m dia, rubber gasket and foam strip
Used with: Premier DX180, DX200, DX400
Vent Cowl VC10
Ref. 89531AA
Provides weather protection for a
100mm PVCu rigid ducted outlet
Pushfit and should be secured with
solvent adhesive
Material: PVCu
Colour: Grey
Used with: Premier DX180, DX200, DX400,
DX100 axial models in exposed situations.
Cowl diameter: 200mm
w201 x h101 x inner 110mm
Glass Mounting Kits GMK & DXDG
Premier glass mounting kit GMK
Ref. 90546AA
Used for installing Premier DX180, DX200
and CF20 models in a window
Glass thickness: 4-28mm
DX100 double/triple glazing kit DXDG
Ref. 07439AA
Allows DX100/LV100 to be mounted in
double glazed panels from 6 to 46mm thick
GX Wall Kit WK
For GXC9 models
Ref. 89372AA
For GX6/GXC6 models
Ref. 89370AA
For bridging cavity walls or lining solid double
brick walls
Steel wall liner. Length 280mm
Set of 508mm ladder strips
255mm
Hole diameter: 267mm
Condensation Trap XCT100
Ref. 89749AA
For use with 100mm dia ducting Prevents condensed water running
back down the duct towards the fan in
vertical PVCu pipe ducted applications.
(Not suitable for use in a flexible duct run)
Collected water must be piped to a
convenient disposal point
Colour: Grey
20mm drain off point
Material: PVCu
Length: 85mm
Easy-Fix Termination Kit EFT
Ref. 90427AA
Designed to be installed from inside abuilding through a cored out to 115mm
(nominal) hole drilled in brickwork
Easily cut to length
Simple installation save times and cost
Four sealing rings provide a watertight
seal in the external wall
Used with: Premier DX180, DX200, CF20.
Not suitable for 100mm axial fans
Length: 465mm
Airbrick Adaptor XAA
Ref. 89777AA
A fabricated G.S.M 340mm sleeve to
bridge a cavity and line a solid wall
Connects to 100mm duct
Includes an air brick
GSM adaptor
Used with all 100mm fans. w220 x h65 x d340 100mm
Spigot Plate SP100
Ref. 89697AA
Connects a duct to the wall face
100mm spigot
Material: Plastic
Used with: All ducted 100mm fans.
For larger diameter spigot plates see page 81
w180 x h180 x 96.5
Fire Damper XFC
XFC100 Dia. 100mm Ref. 89843AAXFC125 Dia. 125mm Ref. 89844AA
XFC160 Dia. 150mm Ref. 89845AAXFC200 Dia. 200mm Ref. 89846AA
For ducts, walls and ceilings. Should not be fitted
into flexible ducting. Wall or duct in which XFC is
fitted should have a rated fire integrity in
accordance with Building Regulations Part B
Provides full 1 hour fire check
Closing temperature 72OC
Low temperature drop
Tested at Warrington Fire Research Centreto BS476 Part 20
-
7/31/2019 2 - Kitchen and Utility Rooms
24/24
pelairDomesticSensors,Switches&A
ccessories
Wall Grille Gravity Shutter XXWG4
White Ref. 90174AW
Grey Ref. 90140AA
Protected duct outlet fitted with gravity flaps
100mm dia connection
Dimensions: w155 x h155 x d15mm
Wall Kit XXSWK4
Ref. 90333AW
100mm wall kit consists of wall duct,
internal and external grilles foam strips
and wall fixings
Used with: XXS100
Wall hole dia. 117mm
Wall Vent Kit VK10
Ref. 89120AW
To bridge a cavity or line a solid wall hole Complete with wall duct (WD), 155mm
square external back-draught shutter, foam
strip and wall fixings
Grille w155 x h155
Wall hole dia. 117mm
Exterior Storm Cowl XXSCW XXSCB
XXSCW White Ref. 90461AW
XXSCB Brown Ref. 90462AB
Provides protection against severe
backdraughts and water ingress
Fitted with gravity flap damper
Wall mounted
100mm spigot
Used with: 100mm axial fans.
Termination Ducting Kit WT
WT10 100mm Ref. 89538AA
WT15 150mm Ref. 89687AA
For use in through wall applications, ducting
can be terminated on the spigot
Complete with exterior wall grille (CFWG), wall
duct (WD), spigot plate (SP), fixing screws
and plugs
Wall hole dia. 117mm
Slimline Wall Kit SLWK
SL100 Wall Kit Ref. 91232AW
SL150 Wall Kit Ref. 91233AW
Wall kit consists of wall duct and external grille
Used with: Slimline SL100 and SL150
Adjustable length 215-380mm
Wall hole size
SL100 117mm
SL150 157mm
Slimline Window Kit SLGK
SL100 Window Kit Ref. 91234AW
SL150 Window Kit Ref. 91235AW*
Window kit consists of internal housing and
external grille box
Used with: Slimline SL100 and SL150
* Backdraught shutter must be removed
Window hole size
SL100 100mm
SL150 150mm
Wall Grille CFWG
CFWG100 - Grey Ref. 89215AB
CFWG100 - White Ref. 89742AW
CFWG150 - Grey Ref. 89690AB
CFWG150 - White Ref. 89857AW
Surface mounted exterior wall outlet grille
For use with 100mm / 150mm nominal
size ducting
Fixing screws provided
Use with: 100mm axial variants.
Dimensions: w150 x h150 x d13mm (CFWG100)
w217 x h217 x d24mm (CFWG150)
Air Replacement Door Grilles DG-W DG-B
DG-W White Ref. 89529AA
DG-B Brown Ref. 89530AA
Tight closing bathroom / toilet doors
prevent air circulation to the fan. Air
replacement grilles permit air to flow
into the room with the door shut
Slimline design
Consists of two grilles and fixings
Minimum door thickness 35mm
Dimensions: w454 x h90mm overallw435 x h77mm hole
Xpelair Domestic Accessories