2015+ AUDI S3 SwitchPath™ and Track Edition
Exhaust Contact us with any installation questions. 215-658-1670 AWE-Tuning.com [email protected]
Congratulations on your purchase of the AWE Tuning
SwitchPath™ and Track Edition Exhausts for the 2015+ Audi S3
2.0T.
Exquisite build quality with industry leading performance
distinguishes this exhaust from all others.
INSTALLATION GUIDE
Copyright 2015, AWE Tuning. No part of this document may be reused or duplicated without the express permission of AWE Tuning/Secor Ltd. All rights reserved. Rev1.0
PERFORMANCE ENGINEERING FOR EUROPEAN AUTOS
2
With engine off, unplug the wiring harnesses from the valve ac-
tuation motors, at arrows in Figure 1.
Remove factory exhaust.
If you intend to install an AWE Tuning Performance Downpipe or
any other brand downpipe at the same time as your cat back
exhaust system, it is recommended that you install the down-
pipe :rst to make cat back alignment easier.
PARTS LIST
Figure 1
SwitchPath™ Exhaust
1 inlet adapter (part LG)
1 mid section (part QV)
1 rear muf?er (part QW)
1 left outer tailpipe w/valve (part QY)
1 right outer tailpipe w/valve (part QZ)
2 inner tailpipe (part QX)
4 tips (choice of size/color)
2 3.00" Accu-Seal clamp
4 63.5mm Accu-Seal clamp
4 2.62" T-bolt clamp
2 M6 bolt
2 M6 lock washer
2 M6 nut
2 hanger post clamp
1 9/64" allen wrench (for hanger post clamp)
Track Edition Exhaust
1 inlet adapter (part LG)
1 mid section (part QV)
1 rear muf?er (part QW)
1 left outer tailpipe (part RJ)
1 right outer tailpipe (part RK)
2 inner tailpipe (part QX)
4 tips (choice of size/color)
2 3.00" Accu-Seal clamp
4 63.5mm Accu-Seal clamp
4 2.62" T-bolt clamp
2 M6 bolt
2 M6 lock washer
2 M6 nut
2 valve harness block-off
2 hanger post clamp
1 9/64" allen wrench (for hanger post clamp)
Step 1
Copyright 2015, AWE Tuning. No part of this document may be reused or duplicated without the express permission of AWE Tuning/Secor Ltd. All rights reserved. Rev1.0
Install inlet adapter LG into mid section and secure with a 3" ac-
cu-seal clamp (do not fully tighten), at Arrow A in Figure 2.
Install mid section QV into muf?er inlet and secure with a 3" ac-
cu-seal clamp (do not fully tighten), at Arrow B in Figure 2.
Figure 2
Step 2
A B
3 Copyright 2015, AWE Tuning. No part of this document may be reused or duplicated without the express permission of AWE Tuning/Secor Ltd. All rights reserved. Rev1.0
Use the supplied M6 hardware to secure the passenger and
driver side tailpipe tabs, at arrow in Figure 4. Do not tighten at
this time.
Install all the tips using the supplied 2.62" t-bolt clamps and ad-
just depth and rotation to suit. Do not tighten at this time.
Start at the front and begin fully tightening the accu-seal
clamps. Work toward the rear ensuring the tips are aligned and
adjust as needed
Once all clamps are fully tightened and tips look correct, tighten
the M6 bolts on the outlet tab, at arrow in Figure 4. Figure 4
Step 4
For SwitchPath™ Exhaust installs, swap the factory valve
actuator motors from the factory exhaust onto the mounting
brackets on AWE Tuning tailpipes. Secure using the factory
hardware, as shown in Figure 3.
For both SwitchPath™ and Track Edition Exhausts, install in-
board tailpipes into muf?er outlets and secure with the supplied
63.5mm accu-seal clamps. Then install the outer tailpipes into
muf?er outlets and secure with the supplied 63.5mm accu-seal
clamps. Do not tighten clamps at this time. Figure 3
Step 3
Step 5
Once the exhaust system is properly adjusted, install a hanger
post clamp on each of the rear muf?er hanger posts, as shown
at arrow in Figure 5. Slide the clamp onto the hanger post so
that it sits snug against the rubber element, and then tighten
down with the enclosed allen wrench.
These clamps will keep the exhaust from sliding laterally under
usage and will keep the tips properly aligned in the valance
openings.
Finally, on SwitchPath™ Exhausts, reconnect the valve motor
wiring harness to each valve.
On Track Edition Exhaust, install supplied block offs into the
wiring harness connectors to protect them.
Figure 5
4Copyright 2015, AWE Tuning. No part of this document may be reused or duplicated without the express permission of AWE Tuning/Secor Ltd. All rights reserved. Rev1.0
ENJOY
Any questions or comments,
please do not hesitate to contact us:
215-658-1670
AWE-Tuning.com
Once installed properly, your AWE Tuning Exhaust will provide a lifetime of trouble-free performance.
PERFORMANCE ENGINEERING FOR EUROPEAN AUTOS
5
Thank you for choosing AWE Tuning as your performance automotive parts supplier. Please remember
that a performance car is only as strong as its weakest link. Therefore, it is vital that you maintain your
vehicle to factory speci:cations.
By installing or using the purchased product, the Consumer accepts this warranty and any speci:c
Manufacturer warranties enclosed.
Limited Warranty
The following warranty is valid only in the United States.
The Manufacturer’s full warranty applies to all products sold.
Secor Ltd. (AWE Tuning) warrants to the original retail purchaser (Consumer) this product (2015+ S3 2.0T
Exhaust) from date of original purchase against manufacturing defects for:
ONE YEAR on tip :nish
LIFETIME on balance of parts
Upon veri:cation of warranty coverage, AWE Tuning will repair or replace the defective product at their
discretion, without charge. This is the only remedy the Consumer has for any loss or damage, however
arising, due to nonconformity in or defect of the product. This warranty does not cover consequential
damage, loss of time or revenues, shipping costs, labor costs, inconvenience, loss of use of vehicle, dam-
age to the vehicle or components, or other incidental or indirect damage.
All warranties are void if the product was not installed by a certi:ed auto mechanic, improperly serviced,
modi:ed, or used in a way not intended by the Manufacturer. Use of product in Motorsports or Racing
conditions is grounds for warranty denial. Motorsports and Racing is an inherently abusive operational
condition, and it is impossible to warranty for this type of usage.
The Consumer is responsible for ensuring that the product is installed in a safe and proper manner, and
should cease usage of the product immediately if an unsafe or improper condition is noted. If an unsafe or
improper condition is noted, the Consumer should then immediately contact the facility where the product
was installed or AWE Tuning directly.
Please contact the original place of purchase for any warranty claims or explanations of this document.
AWE Tuning
199 Precision DriveHorsham, PA 19044
215-658-1670
Copyright 2015, AWE Tuning. No part of this document may be reused or duplicated without the express permission of AWE Tuning/Secor Ltd. All rights reserved. Rev1.0
PERFORMANCE ENGINEERING FOR EUROPEAN AUTOS