A R C H I T E C T U R A L D E T A I L F I L E2-16 0 1 / 0 6
W o o d w r i g h t ® D o u b l e - H u n g I n s e r t W i n d o w s
Contents
Woodwright® Double-Hung Insert Windows
Basic Unit Details
Woodwright® Double-Hung Insert/Full Frame Comparison ... 2-17
Woodwright® Double-Hung Insert Units ............................... 2-18
Woodwright® Double-Hung Insert Location Details ............. 2-19
Woodwright® Double-Hung Insert Sill Angles ...................... 2-20
Woodwright® Double-Hung Insert Picture Units .................... 2-21
Woodwright® Double-Hung Insert Transom Units .................. 2-22
Options / Accessories
Andersen® Grilles ................................................................. 2-23
Installation Trim Parts .......................................................... 2-25
Joining Details ......................................................................... 2-26
Anchoring Methods .................................................................. 2-27
• Custom sizing
• 3 sill angles available — 0°, 8° and 14°
• Installation kit includes screws, straight shims, and backer rod
• Traditional styling
• Andersen™ 400 Series Divided Light grille options
A R C H I T E C T U R A L D E T A I L F I L E 2-17 0 1 / 0 6
W o o d w r i g h t ® D o u b l e - H u n g I n s e r t W i n d o w s
Woodwright® Double-Hung Insert and Woodwright Double-Hung Window Full Frame Comparison Scale 3" = 1'-0" (1:4)
Shim at sill under each side jamb
Rough openingframing
Rough openingframing
Rough openingframing
Rough openingframing
Exterior Interior Exterior Interior
Existing windowcomponents
Existing windowcomponents
Existing sill angle
Woo
dwrig
ht®
Full
Fram
e U
nit H
eigh
t
Woodwright® Insert Unit HeightWoodwright® Full Frame Unit Height
Exis
ting
Open
ing
Heig
ht
Woo
dwrig
ht®
Inse
rt U
nit H
eigh
t
Roug
h Op
enin
g He
ight
WOODWRIGHT® DOUBLE-HUNG FULL FRAME WINDOWWOODWRIGHT® DOUBLE-HUNG INSERT WINDOW
1/2" (13)
1/4" (6)typical
Space at head plus shim at sill equal 1/2" (13)
The unit dimension height and the rough opening height are equal dimensions. This is because the nose of the window frame is 1/2" (13) below the window unit as it rests on the rough opening sill. Therefore, the rough opening height allowance for the window is 1/2" (13). This is the minimum rough opening allowance. The rough opening may need to increase depending upon your particular installation and materials used.
The Woodwright® insert unit height is determined by measuring the Existing Opening Height. Measurement is taken from the underside of the existing head jamb to the highest point of the existing sill. Therefore, the unit height of the insert window is always specified referring to the interior side of the window.
Use this dimension for determining united inches of window for pricing.
= Existing window and trim
The Woodwright double-hung insert window is an insert frame version of the Woodwright full frame double-hung window. It shares many features, benefits, and options with the Woodwright full frame window. The details below describe measuring and rough opening differences.
A R C H I T E C T U R A L D E T A I L F I L E2-18 0 1 / 0 6
W o o d w r i g h t ® D o u b l e - H u n g I n s e r t W i n d o w s
Basic Unit Details - Woodwright® Double-Hung Insert Window
Basic Unit Scale 3" = 1'-0" (1:4)
Head
Check Rail
ClearOpeningHeight
Unit
Heig
ht
Exis
ting
Open
ing
Heig
ht
Sill
Andersen®Woodwright®double-hunginsert window
Existingparting stopremoved
Multiple sill angle options: 14°, 8°, 0°
Optional Andersen®exterior trim stop cover
14°
14°
3-1/4" (83)jamb depth
2-11/16" (68)
4" (102)
1/4" (6)typical - see note
Jamb Jamb
Andersen Woodwright double-hung insert window upper sash
Lower sash
Existingparting stopremoved
Clear Opening Width
Unit Width
Existing Opening Width
3-1/
4" (8
3)ja
mb
dept
h
1-11/16"(43)
1-11/16"(43)
= Existing window and trim
3/16" (5)typical - see note
3/16" (5)typical - see note
Vertical Section
Horizontal Section
Note:
Each new insert window must be downsized sufficiently to allow it to be shimmed, leveled and squared inside the original window frame. The condition of the existing window frame may require downsized dimensions different from those shown in these details.
A R C H I T E C T U R A L D E T A I L F I L E 2-19 0 1 / 0 6
W o o d w r i g h t ® D o u b l e - H u n g I n s e r t W i n d o w s
Location of Woodwright® Double-Hung Insert Window in Existing Window Opening
Existing opening width
Existing opening height
Existing sill angle
Jamb Jamb
Existing Opening Width
Existing inside stop
Interior
Interior
Existing stool
Existing sill
Existingsill angle
Existing parting stop(typically removed)
Existing exterior stop
Existing inside stop
Existing parting stop(typically removed)
Existing exterior stop
Existing Opening Height
Existing interior trim
Horizontal Section
Vertical Section
Existing interior trim
Existing exterior trim
Head
Check Rail
Andersen Woodwright Double-Hung Insert Window
Andersen Woodwright Double-Hung Insert Window
= Existing window and trim
1
2
3
1
2
3
Required Measuring Information to Properly Specify Insert Windows
Always confirm that existing frame opening is plumb, square and level to accept the new insert window.
IMPORTANT
Scale 3" = 1'-0" (1:4)
A R C H I T E C T U R A L D E T A I L F I L E2-20 0 1 / 0 6
W o o d w r i g h t ® D o u b l e - H u n g I n s e r t W i n d o w s
Sill Angle OptionsScale 3" = 1'-0" (1:4)
8° Sill Detail
14° Sill Detail
0° Sill Detail
Existing wall
Existing window sill11° to 15° angle
Existing window sill 5° to 10° angle
Existing window sill0° to 4° angle
14° slope
Existing wall
Existing wall
Exis
ting
Open
ing
Heig
htEx
istin
g Op
enin
g He
ight
Exis
ting
Open
ing
Heig
ht14° slope
14° slope
Select the Woodwright® insert window sill angle that most closely matches the existing sill angle. Units with smaller sill angle will have larger maximum.
Note: Insert window is shown slightly elevated from existing sill for illustration clarity. New insert window will sit directly on existing sill.
A R C H I T E C T U R A L D E T A I L F I L E 2-21 0 1 / 0 6
W o o d w r i g h t ® D o u b l e - H u n g I n s e r t W i n d o w s
= Existing window and trim
Unit
Heig
ht
Exis
ting
Open
ing
Heig
ht
Unit
Heig
ht
Exis
ting
Open
ing
Heig
ht
14° Sill
Head
Head
0° Sill
Vertical Section
Horizontal Section Vertical Section
OptionalAndersen®exteriortrim stopcover
OptionalAndersen®exteriortrim stopcover
OptionalAndersen®exteriortrim stopcover
Jamb Jamb
Unit Width
Existing Opening Width
3"(76)
3"(76)
4"(102)
3" (76)
4"(102)
1-1/16"(27)
4-7/16" (113)
4-7/16" (113)
3-1/4" (83)
1/4" (6)typical - see note
1/4" (6)typical - see note
1/4" (6)typical - see note
3-1/4"(83)
3-1/4" (83)
Head
Unit
Heig
ht
Exis
ting
Open
ing
Heig
ht
8° Sill
Vertical Section
OptionalAndersen®exteriortrim stopcover
3"(76)
4"(102)
5/8"(625)
4-7/16" (113)
3-1/4" (83)
3/16" (5)typical - see note
3/16" (5)typical - see note
Basic Unit Details - Insert Picture Window
Picture Unit Scale 3" = 1'-0" (1:4)
Note:
Each new insert window must be downsized sufficiently to allow it to be shimmed, leveled and squared inside the original window frame. The condition of the existing window frame may require downsized dimensions different from those shown in these details.
A R C H I T E C T U R A L D E T A I L F I L E2-22 0 1 / 0 6
W o o d w r i g h t ® D o u b l e - H u n g I n s e r t W i n d o w s
Basic Unit Details - Insert Transom Window
Transom Unit Scale 3" = 1'-0" (1:4)
= Existing window and trim
Head
Sill
OptionalAndersen®exteriortrim stopcover
3"(76)
3"(76)
3-1/4" (83)
Horizontal Section
OptionalAndersen®exteriortrim stopcover
Jamb Jamb
Unit Width
Existing Opening Width
3" (76)
3-1/4"(83)
Unit
Heig
ht
Exis
ting
Open
ing
Heig
ht
1/4" (6)typical - see note
3/16" (5)typical - see note
3/16" (5)typical - see note
Note:
Each new insert window must be downsized sufficiently to allow it to be shimmed, leveled and squared inside the original window frame. The condition of the existing window frame may require downsized dimensions different from those shown in these details.
A R C H I T E C T U R A L D E T A I L F I L E 2-23 0 1 / 0 6
W o o d w r i g h t ® D o u b l e - H u n g I n s e r t W i n d o w s
White
Sandtone
Terratone®
Forest Green
3/4"
7/8"
1-1/8"
2-1/4"
With Spacer
Without Spacer
Maple
Oak
Prefinished
Pine
Colonial
Modified Colonial
Modified Col W/Check Rail
Prairie A
Short Fractional
Short Fractional W/Check Rail
Tall Fractional
Tall Fractional W/Check Rail
Victorian
Renaissance
Sunburst
Specified Equal Light
Custom
HP/HP Tempered
HP Sun/HP Sun Temp
3/8" Low-E/Temp
Single-Pane Impact
Available now
Available only with 3/8" glass through the Andersen Divided Light program
Please check with Andersen for availability
Andersen®400 Series Windows
Gla
ss
Patt
erns
In
terio
r Ty
pe
Wid
th
Exte
rior C
olor
Andersen®400 Series Doors
Case
men
t & A
wnin
g
Case
men
t Pic
ture
Glid
ing
Woo
dwrig
ht®
Doub
le-H
ung
& Tr
anso
m
Woo
dwrig
ht®
Pict
ure
Woo
dwrig
ht®
Arch
top
& U
nequ
al L
eg A
rcht
op
Woo
dwrig
ht®
Sprin
glin
e™ S
ingl
e-Hu
ng
Woo
dwrig
ht®
Doub
le-H
ung
Inse
rt Pr
oduc
ts
Tilt-
Was
h Do
uble
-Hun
g &
Tran
som
Tilt-
Was
h Pi
ctur
e
Circ
le To
p™ &
Qua
rter R
ound
Arch
Sprin
glin
e™
Flex
ifram
e®
Ellip
tical
Circ
le &
Ova
l
Goth
ic
200
Serie
s Na
rrolin
e® D
oubl
e-Hu
ng &
Tran
som
Fren
chwo
od®
Glid
ing
Fren
chwo
od®
Hing
ed In
swin
g
Fren
chwo
od®
Hing
ed O
utsw
ing
Fren
chwo
od®
Patio
Doo
r Sid
elig
hts &
Tran
som
s
Options / Accessories
Andersen® Divided Light Grilles
A R C H I T E C T U R A L D E T A I L F I L E2-24 0 1 / 0 6
W o o d w r i g h t ® D o u b l e - H u n g I n s e r t W i n d o w s
3/32"
5/16"
5/16" 7/16"
7/16"
45˚
2-1/4"
53˚3/8"3/8"3/8" 53˚
7/8"
45˚45˚
3/4"
53˚ 35˚
1-1/8"
35˚
1/2"
1-13/16"
5/16" 7/16"
2-1/4"7/8"3/4" 1-1/8"
1/2" 1-13/16"
5/16"5/16"5/16"
Permanent Exterior Fibrex® Material Grille Profiles (chamfer profile). Also used for pre-finished interior, except 400 Series Woodwright® double-hung windows.
Permanent Interior Wood Grille Profiles (chamfer profile).
Andersen® Finelight™ Grilles-Between-the-Glass.
3/8"
3/4"
1/2"
1"
Andersen® Divided Light GrillePermanent ExteriorPermanent Interiorwith Spacer
Andersen® Divided Light GrillePermanent ExteriorPermanent Interior
Andersen® Divided Light GrillePermanent ExteriorRemovable Interior
RemovableInterior
Andersen® Finelight™Grilles-Between-the-Glass
Options / Accessories
Grille Profiles • Scale = Full • Dimensions include thickness of tape.
400 Series Grille Options
A R C H I T E C T U R A L D E T A I L F I L E 2-25 0 1 / 0 6
W o o d w r i g h t ® D o u b l e - H u n g I n s e r t W i n d o w s
Options / Accessories
Installation Trim Parts Scale 3" = 1'-0" (1:4)
Head
Interior trim stop (cut to fit)
Exterior trim stop (cut to fit)
9/16" (14)
Optional Andersen®interior trim stop with dual face profile. Cut to width and length as needed.
Andersen® exterior trim stops are supplied with each unit. Cut to width at job site.
Optional Andersen® exterior joining strip.
Optional Andersen®interior joining strip.
Interior Trim Stop
Exterior Trim Stop
Interior Joining Strip
Exterior Joining Strip
2-5/8" (67)
2" (51)
7/16" (11)
1-15/16"(49)
5/16" (8)
1-11/16"(43)
1/4" (6)
84" (2134)or
48" (1219)
144"(3658)
144"(3658)
A R C H I T E C T U R A L D E T A I L F I L E2-26 0 1 / 0 6
W o o d w r i g h t ® D o u b l e - H u n g I n s e r t W i n d o w s
Optional exterior trim strip Optional exterior trim strip
Optional interiortrim strip
Optional interiortrim strip
Unit
Heig
htUn
it He
ight
Optional exterior trim strip
Optional exterior trim strip
Woodwright®double-hunginsert window
Woodwrightdouble-hunginsert window
Woodwrightdouble-hunginsert window
Woodwrightdouble-hunginsert window
Woodwrightdouble-hunginsert window
FixedPicturewindow
Fixed Transomwindow
FixedPicture
FixedPicturewindow
FixedPicture
Fixed Transomwindow
0"
Optional interiortrim strip
Unit
Heig
htUn
it He
ight
0"
Unit HeightUnit Height0"
Unit HeightUnit Height0"
6" (152)
Optional interiortrim strip
6" (152)
6" (152)5-11/16" (144)
Scale 3" = 1'-0" (1:4)
Non-Reinforced One Way Joining — Vertical or Horizontal
Picture or Transom Insert to Picture or Transom Insert Window
Double-Hung Insert to Double-Hung Insert Window
Transom Insert Over Picture or Transom Insert Window
Transom Insert Over Double-Hung Insert Window
A R C H I T E C T U R A L D E T A I L F I L E 2-27 0 1 / 0 6
W o o d w r i g h t ® D o u b l e - H u n g I n s e r t W i n d o w s
The Woodwright® double-hung insert window is secured in the existing window frame by using 2” (51) screws and shims through the side jambs of the insert window into the existing window frame.
Shims, screws and backer rod are included with each insert window.
Anchoring Method
Installation Screws Scale 3" = 1'-0" (1:4)
JambJamb
#8 x 2" screws fastened into existing frame
Andersen® shims
Exterior Installation
JambJamb
#8 x 2" screws fastened into existing frame
Interior stops replaced after installationor use optional Andersen® interior stops
Backer rod and sealant
Backer rod and sealant
Andersen® shims
= Existing window and trim
Interior Installation
Andersen shim