Download - 8d in typical industries
7/29/2019 8d in typical industries
http://slidepdf.com/reader/full/8d-in-typical-industries 1/13
This article was downloaded by: [University of Mysore ]On: 10 January 2013, At: 23:39Publisher: Taylor & FrancisInforma Ltd Registered in England and Wales Registered Number: 1072954 Registered office: MortimerHouse, 37-41 Mortimer Street, London W1T 3JH, UK
Journal of the Chinese Institute of IndustrialEngineersPublication details, including instructions for authors and subscription information:http://www.tandfonline.com/loi/tjci20
A case study in solving customer complaints based onthe 8Ds method and Kano modelHsiang-Ru Chen & Bor-Wen Cheng
a a
aDepartment of Industrial Engineering and Management, National Yunlin University of
Science and Technology, 123 University Road, Section 3, Douliou, Yunlin 64002, Taiwan,Republic of ChinaVersion of record first published: 14 Jun 2010.
To cite this article:Hsiang-Ru Chen & Bor-Wen Cheng (2010): A case study in solving customer complaints based on the8Ds method and Kano model, Journal of the Chinese Institute of Industrial Engineers, 27:5, 339-350
To link to this article: http://dx.doi.org/10.1080/10170669.2010.495508
PLEASE SCROLL DOWN FOR ARTICLE
Full terms and conditions of use: http://www.tandfonline.com/page/terms-and-conditions
This article may be used for research, teaching, and private study purposes. Any substantial or systematic
reproduction, redistribution, reselling, loan, sub-licensing, systematic supply, or distribution in any form toanyone is expressly forbidden.
The publisher does not give any warranty express or implied or make any representation that the contentswill be complete or accurate or up to date. The accuracy of any instructions, formulae, and drug dosesshould be independently verified with primary sources. The publisher shall not be liable for any loss, actions,claims, proceedings, demand, or costs or damages whatsoever or howsoever caused arising directly orindirectly in connection with or arising out of the use of this material.
7/29/2019 8d in typical industries
http://slidepdf.com/reader/full/8d-in-typical-industries 2/13
Journal of the Chinese Institute of Industrial EngineersVol. 27, No. 5, September 2010, 339–350
Acasestudyinsolvingcustomercomplaintsbasedonthe8DsmethodandKanomodel
Hsiang-Ru Chen and Bor-Wen Cheng*
Department of Industrial Engineering and Management, National Yunlin University of Science and Technology,123University Road, Section 3, Douliou, Yunlin 64002, Taiwan, Republic of China
(Received August 2008; revised September 2009; accepted April 2010)
Service economics is growing in importance, and satisfying customers is a major objective of enterprises. Product or service quality involves knowing what the customers’ needs are and how tofulfill those needs to meet their expectations and requirements, especially when customer complaintsappear. In this study, the Kano model is used to distinguish various product and service satisfactionordissatisfactiontypes,basedoncustomers’opinions.The8disciplines(8Ds)problem-solvingmethodisacorrectiveactionprocedureusedtoidentifyandcorrectcausesofnon-conformanceandisadoptedin this article when the customer complains about a product or service. A case study in this articleisbasedonthe8DsmethodandKanomodel,whichprovidesastructuredandflexibleframeworkfor
acustomer-orientedmanagementsystemtodrivetheimprovementofbusinessperformance.Bywayof differenthistogramcomparisons,apairedt test,andCpkestimations,acontrolmodelisestablishedtoidentifywhatthequalitylevelis.Aftercompletingthecorrectiveactionsandexcludingthevariationof sheet metal hardness factor, the defect rate decreased from 28% to 0.5%, and this improvementresulted in gains of at least 22 million New Taiwan dollars.
Keywords:customer complaints; 8Ds; problem-solving method; Kano model; ISO/TS 16949
1. Introduction
Aspiring to satisfy the customer is the objective of
enterprise. Service quality involves acknowledging
customers’ needs and fulfilling their expectations
and requirements, especially when customer com-plaints appear.Kanoetal.[8]revisedthe‘‘Motivation-Hygiene
Theory’’ofHerzbergetal. [7]toclassifyandshow
distincttypesofqualitythathavedifferentimpacts
on satisfaction in product or service development
and improvement. Deming [5] argued from the
consumer’s standpoint that product qualities are
determined by three crucial factors: the first is the
product itself; the second is the satisfaction cogni-
tion of consumer or user while using the product;
andthethirdistheoperationmanual,instructions,
and maintenance and after-sales service. If any of the above fails, complaints will arise. The International standard, ISO 9001:2008,
promotes the adoption of a process approach
when developing, implementing, and improving
theeffectivenessofaqualitymanagementsystemto
enhancecustomersatisfactionbymeetingcustomer
requirements. The process approach emphasizes the impor-
tance of understanding and meeting requirements,
the need to consider processes in terms of added
value, obtaining results of process performance
and effectiveness, and continual improvement of processes based on objective measurement.
ISO/TS 16949:2009 is a technical specificationwhich, in conjunction with ISO 9001:2008, defines
the quality managementsystemrequirementsfor the design and development, production whenrelevant, installation, and service of automotive-related products.
The ISO/TS 16949 quality system respectscustomer orientations, originally from the cus-tomer’sneedsandrequirements,and,bymeasuringcustomer satisfaction and deficiencies correctedat the end, so pay attention to the complaints of customers and make some efforts to analyze andcorrect the dissatisfaction reasons and thus buildup customer loyalty.
The8disciplines(8Ds)methodisatoolofISO/ TS 16949:2009 and has been widely applied inautomotiveindustriesfor service or productsproblem solving, including the problems withsupplier qualification confirmation, manufacturingprocess deviations, defects, maintenance, customercomplaints, returned purchases, etc. The purposeof this article is to use the 8Ds method to solvecustomer complaints and make the quality of service robust in order to please customers andprovide excellent service.
*Corresponding author. Email: [email protected]
ISSN 1017–0669 print/ISSN 2151–7606 online
2010Chinese Institute of Industrial Engineers
DOI: 10.1080/10170669.2010.495508
http://www.informaworld.com
wnloaded by [University of Mysore ] at 23:39 10 January 2013
7/29/2019 8d in typical industries
http://slidepdf.com/reader/full/8d-in-typical-industries 3/13
The 8Ds is one of the many approaches toproblem solving, and it depends on the natureof the problem and who the people involved are.It then integrates different histogram comparisonsand process capability index (Cpk) estimations tohelp make correct decisions and take correct
actions. Corrective actions in 8Ds are mostlydealing with quality improvement through statisti-calprocess control and analyzingwhenthequalityis out of control or does not meet the customer’srequirements.
Organizations must stop using the ‘‘goalpost’’approach and instead use the statistic controlprocess that defines quality requirements in termsof the distribution about the target value toimprove customer satisfaction.
A case study in this article is based on the 8Dsmethod and Kano model, which provides a
structured and flexible framework for a customer-focused managementsystem to drive theimprovement of business performance.
2. Research issues and hypotheses
2.1 Kano model
The Kano model has been widely applied in manykinds of goods or service industries and canintegrate quality function deployments, failuremodes, and effects evaluation to set up qualityattributes and focus priorities to satisfy customerexpectationsand raise customer satisfaction[1,4,9,10,13].
Which product characteristics will affect satis-faction? Which attributes, from the customer’sviewpoint, must be fulfilled? What level of goods
and services should be attained to meet customer
satisfaction? The voice of the customer providesthe direct information and requests regarding hisor her product and service demands.
Conventionally, some scholars assumed thatthere existed a linear relationship between product
(or service performance) and customer satisfaction[2,3,14]. However, there are times when additional
efforts cannot increasecustomersatisfaction.Progress depends on the ‘‘type’’ of customer
expectations [11].Kano et al. [8] revised the motivator–hygiene
(M–H)theoryanddevelopedatwo-waymodelthat
distinguishes between different quality attributetypes. Zhang and Von Dran [15] argued that
‘‘hygiene features’’ are those that are necessarybut insufficient to ensure user satisfaction. This
study divides quality attributes into five distinct
categories as follows and as shown in Figure 1.
(1) Attractive quality: this attribute has thegreatest influence on how to satisfy cus-
tomerrequirementsiftheattributesarepre-sent and satisfactory attractiveness can
make a product or service superior to thatof competitors.
(2) One-dimensional quality: traditionally, this
attribute is positively and linearly relatedto customer satisfaction. Heightening the
degree of fulfillment of this attribute willraise the degree of customer satisfaction. Therefore, in Kano’s model, the customerreaction depends linearly on the level of
fulfillment only for one-dimensionalrequirements.
Figure 1. Kano model.
340 H.-R. Chen and B.-W. Cheng
wnloaded by [University of Mysore ] at 23:39 10 January 2013
7/29/2019 8d in typical industries
http://slidepdf.com/reader/full/8d-in-typical-industries 4/13
(3) Must-be quality: the customer takes must-be requirements for granted, and the must-be requirements are essential functions of any product or service. Fulfilling the must-be requirements will only lead to a state of ‘‘dissatisfaction’’; if must-be requirements
are not present, the customers will beextremely dissatisfied. However, the fulfill-ment of this attribute does not increasesatisfaction since customers look at it asfundamental.
(4) Indifferent quality: this is an attribute inwhich the quality or absence of qualitydoes not affect customer satisfaction; thus,there is little need to pay attention to thisattribute.
(5) Reverse quality: an attribute whose pres-ence causes customer dissatisfaction and
whose absence results in customersatisfaction.
Various distinct types of satisfaction or dissat-isfaction depend on whether certain customerneeds are completely fulfilled. Therefore, goodsor service suppliers must understand the qualitycategories and develop them so as to be morevaluable, even though Kano’s model has limita-tions of usage and is mostly used for analyzingthe effects of and certainly not for suggesting newproduct features [1].
2.2 8Ds problem-solving method
The concepts of the 8Ds problem-solving methodcanbetracedbacktoUSMilitaryStandard(MIL-STD)1520C[12].Thepurposeofthisstandardsetsforth the requirements for cost-effective correctiveactionanddispositionsystemsfornon-conformingmaterial; so, the primary purposes of a correctiveaction and disposition system are to identify andcorrectthecausesofnon-conformance,preventtherecurrence of wasteful non-conforming material,performance, and quality that reduce the cost of
manufacturing inefficiency, and foster quality andproductivity improvement. TheFordCompany,accordingtotheessenceof
MIL-STD1520C,developedthemethodof‘‘8Ds,’’which defined the problem and collected data orinformation at the beginning, then systematicallyanalyzedthecausesandeffects,andthensolvedtheproblem and prevented future occurrences [6].
The 8Ds problem-solving method is a team-oriented problem-solving organization, andshouldbebased onthetruthand focusedonhowto meetthe requirements of customers.
The 8Ds are most effective in dealing with
long-term problems, primary defects, purchaseorder returns, and cost down and safety issues.
Thesefactorssetupnotonlyaprocedurebutalsoacompletereporttobeabletoverifyactionsaftertheproblem is solved, and can provide support foraknowledgebasethatcanacceleratethesolvingof similar problems and be capable of training thewholeteamtopreventthesameproblemrecurring.
The contents of the 8Ds are as follows:
D1. Team approach: A cross-functional team isorganizedintoasystemtodealwithcustomercomplaints or quality deviations during theproblem solving period.
D2. Describe the problem: This step is to under-stand the problem that affects the quality orcustomer requirements and the causes thatinfluence it.
D3. Develop an interim containmentaction:Because the team is composed of competentmembers, possible reaction activities shouldbe undertaken to control and avoid expan-sion. The team members should define andimplementthoseintermediateactionsthatwillprotect the customer from the problem untilpermanent corrective action is implemented.Interim containment action should follow theISO/TS 16949:2008 quality systemanddepends on the actual approach to make adecisionandverifywithdatatheeffectivenessoftheseactionsappropriately.Thepurposeof this step is to preserve some kind of evidenceand to avoid the outcome from being irreme-
diably enlarged before the problem can besolved and the goal achieved. Documenting,control planning, scheduling, and assigningneeds to track should be done to help ensurecompliance with requirements.
D4. Defineandverifyrootcauses:Tofindtherootcauseofaproblem,weusethe5W2Hmethodto diagram customer requirements, to reviewthe process, and to analyze the problem.
D5. Choose/verify permanent corrective actions:Depending ondifferent kindsof causes, somecorrespondingstrategiesareproposed.Results
are then checked and adjustments made, orsomepermanentcorrectiveactionistaken.D6. Implement and validatecorrectiveactions:
Corrective actions are taken to assure thatthe target is attained and the problem issolved.
D7. Prevent recurrence: Precautionary measuresare set up to avoid similar problems withdefects.
D8. Recognize team and individual contributions:Allteammembersaregivenpositivefeedback. Training and education records are main-tained. The Plan-Do-Check-Act (PDCA)
cycle is followed to attain higher customersatisfaction.
Journal of the Chinese Institute of Industrial Engineers 341
wnloaded by [University of Mysore ] at 23:39 10 January 2013
7/29/2019 8d in typical industries
http://slidepdf.com/reader/full/8d-in-typical-industries 5/13
The8Dsareaneffectivemethodtofindoutthe
root causes ofproblems, and members intheteamcan follow aregular procedureto determine whichcorrective actions are appropriate to avoid future
recurrencesforproactivequalityassurancedecisionmaking.
3. Case study
3.1 Source
3.1.1Sample and procedure
There is a customer complaint concerning theperformance quality of dry wall screws (shown in
Figure 2). Dry wall screws are a kind of thread-forming tapping screws which do not need a pre-
drilled hole before penetrating to join two sheet
metals with the thread extruding the material andthe female thread forming, but not cutting.In this study, a manufacturer makes approxi-
mately 30 billion pieces with a value of 80 million
dollars per year. The defect rate is approximately28% and causessubstantialmonetarylosses.Defects result in extra reworking as well asdamage to the reputation of the manufacturer.
The high defect rate results in extra labor costs
and customer dissatisfactionfor the screw
manufacturer.ADclientisthelargest customerofthestudied
company. The customer argued that the quality
of the product did not meet its requirements, suchas drive speed time, force, and dimensions; and
even though they extended the acceptable qualitylevel and specification criteria many times, still the
manufacturer failed to improve quality, and cus-tomers demanded refunds and/or lower prices and
the manufacturer lost market share. The customerrequested that all correction actions should be
recorded and the 8Ds reports should be submitteduntil the case was closed.
Therearesomerequirementsofdrywallscrews
that the customer requested which take them into
Kano’s distinct categories.They include thefollowing.
3.1.1.1Quality of product
(1) Functions:
The functions of mechanical properties includethe hardness, the torque strength, that rust resis-tancemustfittheminimumrequirements,andthat
the maximum drive speed time must be 0.6s.
(2) Easy to use:
When drilled into sheet metal, the productshould,innormalpractice,beeasytousewithlightforce.
(3) Dimension stabilization:
Alldimensionsshouldbeinaccordancewiththedrawings provided by the customer.
3.1.1.2Delivery.Products should be delivered ontime to the designated locations requested by thecustomer.
3.1.1.3Communication.A major sales representa-tive should be provided for good communicationand to deal with all the details.
3.1.1.4Documentation.All the documents shouldbe established in accordance with the documentcontrol procedures of the ISO 9001:2008 quality
system, which includes inspection reports, draw-ings, control plans, etc.
3.1.1.5Packing. The packaging and carton stylesneed to comply with customer indication andduring shipment must protect the product fromdamage.
3.1.1.6Price competitiveness.Price should bedetermined by both supplier and customer andcannot be changed by one side. However, the
supplierneedstoreducecostscontinuouslyinorderto help the customer enlarge its market share.
3.1.1.7Without return or get a refund(responsibilities).When products are delivered tothecustomerandflawsdiscoveredsothattheyfailto meet quality requirements, all products shouldbediscardedatthedeliverypointwithoutobjectionor asking for products to be returned. The proce-dure included four steps in this study (shown inFigure 3).
8Ds must be used to correct and improve
the quality attributes. The attractiveness and one-dimensional qualities, which based on fairness,Figure 2. Dry wall screws.
342 H.-R. Chen and B.-W. Cheng
wnloaded by [University of Mysore ] at 23:39 10 January 2013
7/29/2019 8d in typical industries
http://slidepdf.com/reader/full/8d-in-typical-industries 6/13
are not good, should be in the satisfaction inves-tigation form.
3.2 Apparatus
3.2.1Drive speed test machine
A drive speed test machine is shown in Figure 4.It is used to count the time in seconds taken toscrew into the sheet metal. The load force was setat four levels as follows: 10.2, 11, 12, and 14kgin order to make a comparison of performance.
3.2.2Particle image velocimetry
Aparticleimagevelocimetry(PIV)systemisshownin Figure 5. It provides two- or three-dimensionalvelocity maps in flows based on imaging by smallparticlesintheflow,illuminatedbyalaserlightand
via flow visualization and measurement to analyzesmall particle flow. A PIV was used in this studywithhigh-speedphotographytohelpusunderstandhowthethreadpenetratesintothesheetmetalandto assist with our analysis of defective dry wallscrews.
The specifications of the apparatus are asfollows:
(1) Laser type – infrared lasers(2) Wavelength – 808nm (red)(3) Charge-coupled device: full resolution –
512 512pixels
(4) Maximum frame rate – 5145fps.
3.3 Statistical analysis
Minitab 14.0 statistical software was selected asthe tool for data analyses. A histogram and Cpkwas used to compare and illustrate the pre- and
Quality does not
steadily meet the
specification and it
causes customer
complaints
Inspection
Process
Heat treatment
Tools
Too few samples
to judge
Rolling die is failured
Slight invisible
defects occurred
Without lubrication
Violate the SOP
Wrong core hardness
and
surface hardness
Timekeeper found inconsistencies
based on different decimal places
Carburized depth
is not enough
Quality does not
meet specifications
causing customer complaints
Figure 5. Cause and effect diagram.
Investigate customer satisfaction
requirements and classify them into Kano
model attributes.
8Ds must be used to correct and improve the quality attributes.
The attractiveness and one-dimensional qualities, which based onfairness, are not good, should be in the satisfaction investigation
form.
Search for root causes of the problems,
and verify by comparing the Cpk prior to
and after correction.
Announce preventative actions and trace
customer satisfaction.
Figure 3. Case study procedure.
Figure 4. Drive speed test machine.
Journal of the Chinese Institute of Industrial Engineers 343
wnloaded by [University of Mysore ] at 23:39 10 January 2013
7/29/2019 8d in typical industries
http://slidepdf.com/reader/full/8d-in-typical-industries 7/13
post-correctiveactionresultsandverifywhetherthe
improvement had been achieved.Cpk is an index which measures how close a
process is running to its target without deviating
from the specification limitation relative to thenatural variability of the process.
4. Results
Thesatisfactioninvestigationwasdistributedtothecustomer and completed according to the cus-tomer’s perceptions when it was argued thatproduct quality was not good enough. All theevaluation items were evaluated using the cus-tomer’sopinionswithoutanyinterferenceandthen
sent back to the case company immediately. Thecustomer satisfaction investigation was classified
into Kano model categories (shown in Table 1).Accordingtotheresults(showninTable1),we
focusedontheevaluationitemsthatare‘‘must-be’’,‘‘attractive’’,‘‘one-dimensional’’,and ‘‘reversequality’’ categories, and on which evaluations
were ‘‘not good’’ or ‘‘very bad’’. The qualityinvestigation into the dry wall screws came from
the customer and causes for the complaints wereanalyzed and solved by the 8Ds solving method.
The 8Ds problem-solving method was devel-oped as follows.
4.1 Discipline 1
4.1.1 Team approach
Inthis stage, the casecompany established asmallgroup of people with appropriate knowledge,authority, and skill to solve the problem andimplement corrective actions. The group includedsome departments and the team leader was theR&D manager. The quality improvement projectwas called the ‘‘Kano quality study’’ and is shownin Table 2.
4.2 Discipline 2
4.2.1Describe the problem
The customer received some complaints fromtheirend users and they had voiced much discontentwith the product over the past 3 months. Thecustomerhaddoubtsconcerningpossibledefectsin
Table 1. Customer satisfaction investigation.
Evaluation item Excellent Good Fair Not good Very bad
1.Quality productsFunction (required)
a?
Easy to useb
?Dimension stabilization
c?
2.Delivery (on time)a
?3.Communication
b?
4.Documentationa
?5.Packing
a?
6.Price competitivenessb
?7.Without return or get a refund
d?
Notes: Must-be quality.a
bAttractive quality.cOne-dimensional quality.dReverse quality.
Table 2. Kano quality study.
D1 Team approach
The source of the Specificationproblem The product of M4.221mm dry wall screws from American
airlines (AA) customerProject title Kano quality study – customer complaints improvementLeader R&D managerDescription 1.Establish a cross-functional group
2. Integrate resources3.Highlight the objective
4.Solve customer complaints5.Study the preventive measures
344 H.-R. Chen and B.-W. Cheng
wnloaded by [University of Mysore ] at 23:39 10 January 2013
7/29/2019 8d in typical industries
http://slidepdf.com/reader/full/8d-in-typical-industries 8/13
the products, with causes such as the materialsources, thread die accuracy and thread formingshape, heat treatment processes, etc., harming thestructure’ssafetyandrequiringharderworkduringoperation.
This case company gathered the customer’s
feedback and user reports from the satisfactioninvestigationandwasaskedtoprovidenotonlyanimprovement report, but also to correct the prob-lem completely.
Thecompanyprovidedproductsandinspectionreports to the customer. Although the qualityreports showed all products fitting the specifica-tions,thecustomerconsideredthesamplingreportsto be not presenting the actual qualityperformance.
4.3 Discipline 34.3.1Develop an interim containment action
In this stage, the team proposed interim contain-ment actions (shown in Table 3).
4.4 Discipline 4
4.4.1Define and verify root causes
Some items that might influence the quality per-formance were proposed (see the cause and effectdiagram in Figure 5) and the real causes were
checked and marked. The major root causes are as follows:
(1) About the tool
After a long period of working, the rolling diedeveloped someslightinvisibledefects,resultinginthe shape of the thread not being satiated andhollowed (Figures 6 and 7).
Thetimekeepersusedbythecasecompanyand
thecustomer measuredtimeinconsistently because
differentnumbers ofdecimalplaceswereused,e.g.0.1and 0.01s.
(2) About inspections
The sample size was not large enough todetermine whether the performance of the product
lots was qualified and steady or not. The case companyoverexpandedthe test
specificationconditions,which decreasedthe
Table 3. Interim containment actions.
Interim containment action Measurements Responsibility/Date
1. Breakoffmanufacturingandcheckdiesandtools. No problem was found Manufacture departmentXX-XX-20082. Check the process and parameters, if they
aremissedthenputthemrighttothewaywhere they were set.
No problem was found R&D DepartmentXX-XX-2008
3. Increaseinspectionfromonetothreetimes.After increasing the samplingfrequency some inspectingresults deviate the specifica-tion.Warning!
Quality assurance departmentXX-XX-2008Suggestions:Needtocheckthe
causes and improve4. Record the quality performance Present the inspection data
visualize and save it intoMinitab worksheet.
R&D departmentXX-XX-2008
5. Distinguish certificated and un-certificatedproducts
Setupdifferentstorageregionsandmarkthemindividually.
Plant management departmentXX-XX-2008
6. Develop an analysis and correction planCompile all the information of
products and take them toanalyze.
Team
XX-XX-2008
Figure 6. Two different tiny defects appeared on thesurface of the thread.
Figure 7. Abnormal discontinuous shatter.
Journal of the Chinese Institute of Industrial Engineers 345
wnloaded by [University of Mysore ] at 23:39 10 January 2013
7/29/2019 8d in typical industries
http://slidepdf.com/reader/full/8d-in-typical-industries 9/13
supplier’s returned goods rate but neglected thecustomer’s real expectations.
4.5 Discipline 5
4.5.1Choose/verify permanent corrective action
Therearefourrootcausestobedefined;eachcause
for the problem needs to have a correspondingcorrective action taken and the action should beverified. The result of corrective actions andverifications are illustrated in Table 4.
Because of the different decimal timekeepersused, two different drive speedtime resultsappeared(showninTable5).Whenthetimekeepermeasured the times and rounded them to twodecimal places, the average speed time was 0.447sand there were two samples that exceeded thespecifications. When the timekeeper counted thetimesandroundedtoonedecimalplace,theaverage
speed time was 0.396s and all samples qualified. These different results will cause either acceptanceor rejection of the product.
In this study, 25 dry wall screw pieces withworse threads and 25 pieces with betterthreads were sampled randomly again to compareusing different load forces. The comparisonsof Cpk are shown in Table 6, which showsthat the Cpk of the better thread of dry wallscrewsishigherthan1.67withdifferentloads.Theresults show that the better thread can workin practice with labor-saving and engineeringreliability.
The histogramof skewnessand kurtosismeasurement of the drive speed test is shown in
Figure 8 and shows that the better threads of drywall screws have the superior performance.
In this article, the pairedt test showed thatdifferentloadsandworseandbetterthreadsallaresignificant (Table 7).
4.6 Discipline 6
4.6.1Implement and validate corrective actions
We followed D5 and implementedcorrective
actions, which had been validated, and continuedchecking the performance of the following lot of
production. Every action needed to be recorded
andthedocumentshadtoberevisedresponsiblybycertain people and by certain dates.
Table 4. Choose/verify permanent corrective action.
Root causes Corrective action Verification of action
1. The rolling die shows someslight invisible defects.
Setupthelifeexpectancyandsorttherolling die after producing certainquantities. Lookover andconfirm
the shapes of threads are alwaysfine with optical electronmicroscope.
The inspection report shows thedimensions are qualified.
2. The timekeeper reckoned thetime between the casecompany and customer wasinconsistent because of different decimal places.
Set up timekeeper to two decimals(0.01sec scale) and correspondingwith customer drive speed testmachine.
After the modification we comparedthe drive speed test time, and wefound there were significantdifferences and shown in Table 5.
3. Sample size is too small todetermine the productperformance.
Besides batch sampling, use Cpk tomeasure how closer the process isrunning to its target.
Effectively. The Cpk ofbetter threadishigherthantheworsethreadandtheresultsareinshowninTable6.
4. Overexpanding the load from10.2to 14kgf levels butneglecting the customers’real expectations.
Compare the performance withdifferent loads and narrowedspecification width as a controllimit.
From the histogram in Figure 9, theload of 12kgf, it clearly shows theability and elasticity to deal withcustomers respect. Pairt test
between loads are all significantand shown in Table 7.
Table 5. Drive speed time at different numbers of decimal places.
14kg (rounded down to two decimal places, in 0.01s)
0.42 0.39 0.37 0.36 0.350.47 0.48 0.57 0.43 0.440.45 0.54 0.42 0.42 0.53
0.35 0.38 0.37 0.39 0.460.44 0.43 0.62 0.44 0.65
14kg (rounded down to two decimal place in 0.1s)0.4 0.3 0.3 0.3 0.30.4 0.4 0.5 0.4 0.40.4 0.5 0.4 0.4 0.50.3 0.3 0.3 0.3 0.40.4 0.4 0.6 0.4 0.6
346 H.-R. Chen and B.-W. Cheng
wnloaded by [University of Mysore ] at 23:39 10 January 2013
7/29/2019 8d in typical industries
http://slidepdf.com/reader/full/8d-in-typical-industries 10/13
When all the corrective actions were taken, the
questionnaire on customer satisfaction was sent toreconfirm whether the improvementsweresatisfactory.
First of all, the product quality requirementsinclude‘‘mechanicalfunctions,’’‘‘easytouse,’’and‘‘dimension stabilization’’. When the causes of
defects are realized and solved for the products,then the production line can robustly yield withconfidence.Second, the productionplan andschedulewillkeepupwiththedeliverytimewithoutusing air freight to ship to the customer and withless disagreement in communication. Due to theincrease in quality and absence of any need torework or scrap the product, the cost will reduce,which will reflect on the sales price and enhancecompetitiveness.
Mostoftheevaluationitems,afterthecustomerhad reviewed the samples and reports, showed
that the quality had greatly increased and nowthe product was listed in the good or excellentcategory (Table 8).
4.7 Discipline 7
4.7.1Prevent recurrence
In this step, any failures or defects should be
completely identified; corrections should bedescribedas a systematic group of activities
intendedto:(1)recognizeandevaluate;(2)identifyactionsthatcouldeliminateorreducethechanceof them reoccurring; and (3) document the entirestandard of the process into a drawing and stan-dards. It is important to not only emphasize theproduct and process, but also to understand that
education and more training are essential toprevent the problem from recurring again.
Figure 8. Results of histogram of different loads.
Table 7. Results of pairedt test.
Item N SD difference SE mean difference t-value p-value
14kg(w)–14kg(b) 25 0.051 0.010 8.17 0.000*12kg(w)–12kg(b) 25 0.050 0.010 9.44 0.000*11kg(w)–11kg(b) 25 0.081 0.016 5.81 0.000*10.2kg(w)–10.2kg(b) 25 0.088 0.018 6.26 0.000*
Note: *Significant.
Table 6. Cpk with different loads.
Screw The thread is worse The thread is better
Load (kg) 14 12 11 10.2 14 12 11 10.2Cpk 0.90 0.68 0.38 0.14 2.56 2.43 2.23 1.83
Journal of the Chinese Institute of Industrial Engineers 347
wnloaded by [University of Mysore ] at 23:39 10 January 2013
7/29/2019 8d in typical industries
http://slidepdf.com/reader/full/8d-in-typical-industries 11/13
4.8 Discipline 8
4.8.1Recognizeteamandindividualcontributions
With total quality management development, all
members are needed to be involved in the entireorganization of quality control and be responsibleforthesocialdutiesoftheprocessand/orproduct.Although each company has its own individual
culture, the conscientious participation of teammembers will increase the quality continuously.
5. Conclusion and discussion
Overthepastyears,theapproachpresentedinthisarticle has been thoroughly applied on all tier
suppliers in the automotive industry and thefeedback received from the suppliers has beenvery positive. Again, these methods proved to beveryeffectiveinexplaininghow8DsandtheKano
modelwork,andhowtheycanbeusedandappliedontheshopfloorasapowerfultoolforimproving
quality and customer satisfaction. This study shows that there are three major
factors thataffectedqualityperformance.Thefirstis the different test loads: the heavy load gains the
better outcome in speed time, but it means thatmore force is needed in practice, which is inconve-nient for users. The second is that timekeeper
discrimination should be consistent and accurateaccording to customer requests. Finally, the screw
should have a full thread in the threading processand enable it to be used without extra resistance.
In this study, the Kano model was a good andsimplemethodincompliancewithcustomerrecog-
nition to help the company put emphasis on themost important thing.The 8Dscandistinguishthe
root causes and provide appropriate actions inproblem solving and prevention.
A case study in this article is based on the 8Dsmethod and Kano model, which provide a struc-tured and flexible framework for a customer-focused management system to drive the improve-ment of business performance. After completingthecorrectiveactions,andexcludingthevariationsin sheet metal hardness factor, the defect ratedecreased from 28% to 0.5%, and this improve-ment resulted in gains of at least New Taiwan 22million dollars.
Although the method applied has an excellentresult in this study, thereare some restrictions and
suggestions that need to be observed in futurestudies, which are as follows.
Time limitation: In industrial application, theresult should be achieved within 2 weeks, but itseems to be difficult, when faced with vague orextreme complaints, to achieve this target of finding out the root causes and improving them.
ThestudyintegratestheKanomodelandsimplestatistic methods to solve problems and increasesatisfaction. Other methods such as design of experiment (DOE), theory of inventive problemsolving(TRIZ),etc.,canbeappliedsimultaneously.
The 8Ds method is a problem-solving method.Always remember to revise some documents, suchas failure modes and effects analysis, control plan,processes, and any design records to be a forwardindicator when accomplished a problem.
Rather than trying to avoid mistakes, futurestudy that uses this method needs to encouragebreakthrough ideas regarding the true causes andto learn from the errors or experiences.
Ifaproblemoccurredandthesolutionneglectsthe attributes which must be fulfilled from thecustomer’s viewpoint or what level of goods andservices should be attained or improved to meet
customersatisfaction,the effects are merelypaperwork.
Table 8. Performance of quality and services evaluations after correction.
Evaluation item Excellent Good Fair Not good Very bad
1.Quality productsFunction (required)
a J ?
Easy to useb
J ?
Dimension stabilizationc
J ?2.Delivery (on time)
a J ?
3.Communicationb
J ?4.Documentation
a J ?
5.Packinga
J ?6.Price competitiveness
b J ?
7.Without return or get a refundd
J ?
Notes: Must-be quality.a
bAttractive quality.cOne-dimensional quality.dReverse quality.
348 H.-R. Chen and B.-W. Cheng
wnloaded by [University of Mysore ] at 23:39 10 January 2013
7/29/2019 8d in typical industries
http://slidepdf.com/reader/full/8d-in-typical-industries 12/13
Respecting the customer’s opinions is impor-tant.Manufacturersneednotonlyrealizewhatthecustomer’sdesiresandrequestsare,butalsoclarifytowhichcategorythoserequestsbelong.Customersatisfaction reflects the service or goods perfor-manceofacompany;ahearteningsatisfactionlevel
increases the confidence of customers in using theproduct or service and can heighten the business’scompetence.
Notes on contributors
Hsiang-Ru Chenis currently a PhD student in theDepartment of Industrial Engineering and Managementat National Yunlin University of Science and
Technology, Taiwan. He is responsible for the R&Ddepartment inJauYeouIndustry Co.,Ltd.Hisresearchinterests are in hospital management, quality manage-ment, and industrial management.
Bor-Wen Chengis a professor of Industrial EngineeringandManagementandformerDirectorofHealthServiceManagement at the National Yunlin University of ScienceandTechnologyinTaiwan.Hisresearchinterestsare in the areas of customer relationship management,service quality, and hospital management. He has a BSfrom Tunghai University in Taiwan, an MS, and PhDfrom Auburn University. He is a member of CSQC,CIIE, and CMST.
References
[1] Berger, C., ‘‘Kano’s methods for understanding
customerdefined quality,’’ Center for QualityManagement Journal, 2, 3–35 (1993).
[2] Bhuian, S.N. and B. Menguc, ‘‘An extension andevaluationof job characteristics,organizationalcommitment and job satisfaction in an expatriate,
guest worker, sales setting,’’ Journal of PersonalSelling and Sales Management, 22, 1–11 (2002).
[3] Brock, D.B. and L.M. Sulsky, ‘‘Attitudes towardcomputers: Construct validation and relations to
computer use,’’ Journal of Organizational Behavior,
15, 17–35 (1994).
[4] Clausing,D., TotalQualityDevelopment:AStepBy
Step Guide to World Class Concurrent Engineering,
ASME, New York (1994).[5] Deming, W.E., Quality, Productivity and
Competitive Position, Massachusetts Institute of
Technology Center, Cambridge, USA (1982).
[6] Ford Motor Company, Training Manual for the G-8D Process, Massachusetts Institute of Technology
Center, Cambridge, USA (1999).
[7] Herzberg,F.,B.MausnerandB.B.Snyderman, The
Motivation to Work, Wiley, Nee York (1959).[8] Kano, N., N. Seraku, F. Takahashi and S. Tsuji,
‘‘Attractive quality and must-be quality,’’The
Journal of the Japanese Society for Quality Control,
14, 39–48 (1984).[9] Lofgren, M. and L. Witell, ‘‘Kano’s theory of ¨
attractive quality and packaging,’’ Quality
Management Journal, 12, 7–20 (2005).[10] Matzler, K. and H.H. Hinterhuber, ‘‘How to make
product development projects more successful by
integrating Kano’s model of customer satisfaction
into quality function deployment,’’ Technovation,
18, 25–38 (1998).
[11] Matzler, K., H.H. Hinterhuber, F. Bailom and E.
Sauerwein, ‘‘How to delight your customers,’’
Journal of Product and Band Management, 5, 6–18
(1996).[12] Milstd-1520C,Military Standard: Corrective Action
andDispositionSystemforNonconformingMaterial,
USA (1986).[13] Nilsson-Witell, L., M. Antoni and J. Dahlgaard,
‘‘Continuousimprovementinproductdevelopment:
improvement programs and quality principles,’’
International Journal of Quality and ReliabilityManagement, 22, 753–768 (2005).
[14] Reisinger,Y.andL.W.Turner,‘‘Thedetermination
ofshoppingsatisfactionofJapanesetouristsvisiting
Hawaii and the Gold Coast compared,’’ Journal of
Travel Research, 41, 167–176 (2002).
[15] Zhang,P. and G.M. Von Dran, ‘‘Satisfiers
and dissatisfiers: a two-factor model for
website design and evaluation,’’ Journal of the
AmericanSociety for InformationScience, 51,
1253–1268 (2000).
Journal of the Chinese Institute of Industrial Engineers 349
wnloaded by [University of Mysore ] at 23:39 10 January 2013
7/29/2019 8d in typical industries
http://slidepdf.com/reader/full/8d-in-typical-industries 13/13
Downloaded by [University of Mysore ] at 23:39 10 January 201
8D
*
64002 3 123
(KanoModel)
8Ds
8Ds
T
28% 0.5% 2200
8Ds ISO/TS 16949
(* : [email protected])
350 H.-R. Chen and B.-W. Cheng