Download - AHU manual
Johnson Controls Marine 1
Air Handling Unit Manual
YORK Marine
Johnson Controls Marine 2
Index
Introduction____________________________________________________________________ 4
TEST - PACKING - TRANSPORT ________________________________________________ 5
1.1 TEST __________________________________________________________________________ 5
1.2 PACKING _____________________________________________________________________ 5
1.3 TRANSPORT __________________________________________________________________ 5
1.4 PRELIMINARY CHECK _________________________________________________________ 6
INSTALLATION________________________________________________________________ 7
2.1 POSITIONING __________________________________________________________________ 7
2.2 SECTIONS CONNECTION________________________________________________________ 7
2.3 HYDRAULIC CONNECTION _____________________________________________________ 7
CONDENSATE DISPOSAL _________________________________________________________________ 7
HUMIDIFICATION ________________________________________________________________________ 8
COILS ___________________________________________________________________________________ 8
2.4 Electrical connections ___________________________________________________________ 9
MOTOR_________________________________________________________________________________ 9
SERVO-MOTOR _________________________________________________________________________ 9
ELECTRIC HEATER ______________________________________________________________________ 9
2.5 FAN____________________________________________________________________________ 9
2.6 FILTER_______________________________________________________________________ 10
2.7 AIR DUCTS CONNECTION______________________________________________________ 10
2.8 START-UP _____________________________________________________________________ 10
MAINTENANCE______________________________________________________________ 10
3.1 FILTER SECTION ___________________________________________________________ 10
3.2 COIL SECTIONS _______________________________________________________________ 11
3.3 Drip tray_______________________________________________________________________ 11
3.4 HUMIDIFICATION SECTION ___________________________________________________ 12
3.5 FAN SECTION ________________________________________________________________ 12
Johnson Controls Marine 3
3.6 Dampers _______________________________________________________________________ 16
3.7 SPECIAL SECTION _____________________________________________________________ 16
3.8 VARIOUS CHECKS _____________________________________________________________ 16
PROBLEMS AND INCONVENIENCES ___________________________________________ 16
Johnson Controls Marine 4
Introduction
The purpose of this manual is to provide the service and commissioning engineer with the necessary
knowledge of how to install a York Marine AHU and maintain its functions.
In order to secure the quality of installation and functions the contractor must have the guidelines of
this manual in mind.
Besides describing a correct installation, the manual draws attention to sources of concern.
It is imperative that the engineer familiarizes himself with the content of this manual to ensure a
reliable and efficient operation of the AHU, as York is unable to provide guarantee against damages
occurring during the warranty period if the cause is incorrect installation or use.
Johnson Controls Marine 5
TEST - PACKING - TRANSPORT
1.1 TEST
Following tests are performed before the shipment:
DIMENSIONS CHECK
ASSEMBLED COMPONENTS CHECK
MOTOR - FAN PULLEYS BALANCING AND ALIGNMENT CHECK
FLEXIBLE JOINTS LOCKING ( IF NECESSARY )
GASKETS CHECK
SERIAL NUMBER AND NAME PLATE
1.2 PACKING
The unit is packed with air bubble nylon and all the projecting parts are protected.
1.3 TRANSPORT
We advise to pay particular attention to loading and unloading operations.
Projecting parts must not be used as grip points to move, load or unload the AHU.
During transport the AHU must be tightly fixed in order to avoid damages due to the load
movement.
The AHU can be delivered in separate sections to facilitate transport and positioning.
Holes in the base are made for tubes fixation in order to allow the lifting cables anchoring
when lifting with a crane.
The connection of the various sections composing th e unit is carried out by means of
galvanized bolts. The bolts are to be inserted in the holes in the connection frames. A sealing
gasket is placed on the section’s contact perimeter.
It is extremely important that the air handling unit is put on an appropriate flat base.
Johnson Controls Marine 6
1.4 PRELIMINARY CHECK
When the unit is delivered, check that it has not been damaged during transport. The identification
label must show the correct AHU model and capacities.
The following should be checked:
A) FAN - MOTOR
Manually turn all the shafts to make sure they turn freely.
Clean the fan from any dirt before connecting to ducts and before testing the AHU.
Check that the fan blades have not been damaged.
Check the inspection doors and handles.
B) COILS
Check that manifolds, threading and flanges have not been damaged.
Check that coil fins are not damaged (crushed or crooked) or dirty. In this case restore parts and clean
the pad to avoid clogging.
C) FILTERS SECTION
Check that filters are inserted in their seats and are clean.
D) HUMIDIFICATION SECTION
Check the pump operation.
Check the valve or valve board.
Johnson Controls Marine 7
Check steam generator if selected.
E) SECTIONS CONNECTION
Check that all the sections are perfectly connected with their screws.
Check the parts sealing (gaskets).
NOTE: THE FAN MUST NOT BE RUNNING AND THE MAIN SWITCH
MUST BE OFF BEFORE ANY INTERVENTION INSIDE THE MACHINE
INSTALLATION
2.1 POSITIONING
It is extremely important that the air handling unit is mounted on an appropriate solid flat base.
It is advisable to position the AHU so that normal maintenance is possible, leave sufficient space
on the service side.
2.2 SECTIONS CONNECTION
The connection of sections should be carried out with galvanised bolts inserted in holes on
the connection frames. A sealing gasket is p laced on the sections contact perimeter.
2.3 HYDRAULIC CONNECTION
CONDENSATE DISPOSAL
Coil and humidification sections are provided with a drip pan. The water trap ensures that
condensed water is lead away from the AHU, and also preventing air from entering the AHU from
the discharge connection.
Johnson Controls Marine 8
HUMIDIFICATION
SHIP STEAM
Connect the steam pipe to the solenoid valve mounted on the steam humidification manifold.
Check that connections are made correctly and sealed.
STEAM GENERATOR
Mount the steam generator according to the manufacturer’s guidelines.
WATER/AIR SPRAY NOZZLE HUMIDIFICATION
Connect the supply pipes with water and air to the marked inlets on the valve board.
Before connecting make sure that connections are not damaged or dirty. Check the pipes and ensure
that they are mounted to satisfaction. Check the nozzle in the humidification section.
Close the manually operated regulating valves. Set pressure on the system. Adjust to the desired
pressure by opening the regulating valve, the pressure is shown on the manometers.
COILS
COILS SUPPLIED BY WATER should be connected following the rating plate details; the fluid
must run in counter-current compared to the air flow.
Avoid hydraulic connections and prevent the coil from being extracted.
Johnson Controls Marine 9
STEAM COILS have pipes inclined towards the outlet manifold to facilitate the condensate disposal.
To avoid damages to the coil pay attention to the dimensioning and to the valves adjustment.
DIRECT EXPANSION COILS need adjustment devices and a circuit dimensioning in order to
ensure the oil circulation.
2.4 ELECTRICAL CONNECTIONS
MOTOR
Electric connections must be made according to norms and regulations. Check that the voltage and
the type of power supply correspond to the one shown on the motor name plate. Pay attention during
disassembly and reassembly of the terminal block cover that the gasket should be mounted in its
seat in order to prevent humidity from penetrating. Check the fan rotation direction, in case it is
incorrect invert two of the supply cable phases.
SERVO-MOTOR
SERVO-MOTOR use and maintenance, see manufacture guidelines.
ELECTRIC HEATER
Electric heaters have the circuit connection inside the heater panel. Remember to use a safety
thermostat for protection when mounting the electric heater.
2.5 FAN
Remove transport locks from the fan base frame and locks on other flexible joints.
Check pulleys alignment and electric connections by following the instructions given in the
maintenance programme, paragraph 3.4
Johnson Controls Marine 10
2.6 FILTER
Bag and plan filters should be assembled in the unit approximately after half an hour of machine
operation to clean ducts from dust due to assembly operations.
CHECK THAT FILTERS ARE INSERTED IN THEIR
GUIDES OR FRAMES
2.7 AIR DUCTS CONNECTION
Operations to be carried out are the following:
Clean the flange and position the sealing gasket.
Tighten all the fixation screws.
Put duck tape around the connection to optimise the sealing.
Support ducts to avoid that the duct’s weight is supported by the AHU.
2.8 START-UP
After checking all components proceed to start-up. When starting-up the unit check:
Check dampers calibration.
Check the fan rotation direction.
Frequently check the belt’s tension during the first 24-48 hours.
Check the motor power supply.
Check that filters are inserted in their guides or on proper frames.
Check humidification system.
MAINTENANCE
All the panels can be removed by unscrewing the screws that fix them to the bearing frame.
3.1 FILTER SECTION
PLAN FILTERS
The plan filter is made of synthetic fibres.
Johnson Controls Marine 11
Cleaning of the cells can be done with compressed air or by washing with water. When using
compressed air, be careful not to damage the filter by using a high pressure. The air stream must
be blown in the opposite direction then the air flow is through the filter.
The cleaning interval is approximately 15 days.
Check during operation if the interval should be increased or decreased. At start-up check
the filters more frequently.
BAG FILTERS
The high efficiency filtration is achieved by soft and rigid bag filters.
Bag filters cannot be regenerated therefore the filter must be replaced when dirty.
Bag filters are assembled on frames. To disassemble the filter remove the fixation springs and
slide the filter from the frame. Insert the new filter and secure with the fixation springs.
3.2 COIL SECTIONS
Check that the space between the fins is clean. If dirty use low pressure steam to dissolve and
clean fins and coil. Caution must be shown to avoid damaging or bending the fins.
The heating coil must be protected against freezing up, when not in use. Use an antifreeze
thermostat to secure the heating coil, or use a heating medium that does not expand when
exposed to frost.
3.3 DRIP TRAY
Regularly check that the condensed water can pass the drip tray outlet and water trap. Avoid
clogging of the water discharge pipe.
Johnson Controls Marine 12
3.4 HUMIDIFICATION SECTION
WATER/ AIR NOZZLE HUMIDIFICATION
Frequently check the manometers to ensure correct pressure setting. Check the nozzles
operation with the fan not operating. If the nozzle is not working properly close the shut off
valves on the valve board, both lines. Unscrew the front of the nozzle and clean. Use compressed
air or metal wire of adequate diameter to clear openings.
HIGH PRESSURE STEAM HUMIDIFICATION
Check that the connections are tight-fitting and the solenoid valve is working. To clean the
high pressure steam nozzles, shut off the power and the solenoid valve closes. Dismount the
nozzles and clean with compressed air or metal wire with an adequate diameter.
3.5 FAN SECTION
FAN
Periodically check the centring of the impeller compared to the shaft and its fixation system.
Check there is no slipping of the impeller on the suction inlets.
Remove grease and dirt deposits on the impeller blades. During operation check the bearing
condition by listening to its noise level.
Check the lubricant condition. Radial bearings, lifetime lubricated, have been mounted in machines
where the power to the shaft is low. These bearings are due to work for a minimum operating
lifetime of 20,000 hours.
Fans, where the power to the shaft is higher, are provided with radial bearings housed in cast iron
supports with the possibility of greasing.
Types of grease for bearing lubrication.
Brand Type Base soap Operating temperature
FINA MARSON HTL 3 LITIO -30°C 120°C
SHELL ALVANIA FETT 3 LITIO -20°C 130°C
ESSO BEACON 3 LITIO -20°C 130°C
MOBIL MOBILUX 3 LITIO -30°C 130°C
BEARINGS REPLACEMENT WITHOUT FANS MONOBLOCK
SUPPORT
Remove possible accessories assembled on the fan shaft on both sides.
Johnson Controls Marine 13
Hold, with an adequate device, the fan shaft, giving the possibility to carry out the
following operations, without damaging the impeller or the fan inlets.
Unlock the bearing eccentric ring, paying attention to unscrew the threaded grub fixing it.
By slight pushes make the bearing turn, for instance with a hammer or punches. Repeat
the operation for the other bearing and slide off the fan shaft rings.
Disassemble the dial that holds the bearings by unscrewing the fixing bolt on the fans
side.
Remove the bearings from the shaft, with the help of an extractor.
Reassemble the dials, pay attention to the new bearings that are equipped with rubber
dampers, these should also be replaced.
Insert the bearings equipped with dials in the fan shaft on both sides by approaching
the fan sides in correspondence to the fixation holes.
Insert the eccentric rings and fix them by tightening the threaded grubs.
Manually turn the impeller and make sure there are no anomalous tensions in its
movement or in the bearings movement.
These bearings are “lifetime” lubricated. Their theoretic life time is 20,000 hours, in
normal operating conditions. The temperatures range for these bearings range from
-30°C to +85°C.
BEARING REPLACEMENT IN THE FAN
MONOBLOCK SUPPORTS
Remove possible accessories assembled on the fan shaft on both sides.
Hold, with an adequate device, the fan shaft, giving the possibility to carry out the
following operations without damaging the impeller or the fan inlets.
Unlock the eccentric ring locking the bearing, paying attention to first unscrew the
threaded socket head screw fixing it.
Remove the elastic plugs from bearings cast iron supports.
Unscrew the fixation screws from the fan frame supports.
Remove bearings equipped with supports from the shaft, paying attention to carry out the
operation without damaging the shaft.
Remove bearings from cast iron supports by turning them on their axis, then extract them
from the support.
Johnson Controls Marine 14
Insert the new bearings in the cast iron supports.
Insert them in the fan shaft.
Place the bearing supports on the fan frames, insert the elastic plugs.
Screws on bolts for the support fixation.
Observe the centring of the impellers compared to the fan inlet. Make sure that it is
rotating without friction.
Insert the bearing eccentric rings and tighten them in the shaft direction of rotation, lock them
by screwing the threaded socket head screw.
Manually turn the impeller and make sure there are no anomalous tensions in its
movement or in the bearings movement.
These bearings can be greased. The temperatures range for these bearings range from
-30°C to +110°C.
PULLEYS
The drive is composed by pulleys removable hub type, and “V” belts widely dimensioned.
In order to replace the pulley, follow these instructions:
DISASSEMBLY
Fully loosen all the threaded grub screws, which lock the pulley to the bushing .
Insert one of these grub-screws into the threaded extracting hole.
Tighten the grub-screw until the pulley loosens from the bushing.
Completely remove the pulley and the socket head screw from the shaft.
ASSEMBLY
Clean and degrease the socket head screw hole and the external surfaces and the conic
housing of the pulley. Insert the socket head screw in the pulley hub and align holes
(the half threaded holes must be aligned with half non threaded holes).
Slightly oil the threaded grubs and screw them on, but without tighten them fully.
Clean and degrease the shaft, insert the pulley and the socket head screw on the shaft till
the desired position is reached.
Using an Allen wrench gradually tighten the grubs to the pulley is completely locked.
After having operated the drive under load for a short time (from 24-48 hours), check
again the torque wrench setting.
With every change of pulley, check their alignment with figure
Johnson Controls Marine 15
BELTS
Frequently check the belt’s tension during the first 24-48 hours. An over tensioning reduces the life
of belts and bearings. Keep the belts free from foreign materials that could cause slipping.
Periodically check the drive. Tension it when it slips. The belt should be shortened in the junction
point.
To check a drive tension, use the following procedure
Measure the free section length L.
Apply a force P in the centre of the free section.
Measure Fa and check this value with the one
obtained from the table below.
Fa absolute = L:100xE
Adjust the Fa value to the data read in Fa absolute.
Belt cross section Force applied (kg) Pulley diameter Belts flex. For 100mm of L
E(mm)
SPZ 2,5
71-90
90-125
>125
2,20
2,05
1,90
SPA 5,0
71-100
100-140
140-200
>200
3,20
2,75
2,55
2,45
SPB 7,5
112-160
160-224
114-355
>355
3,00
2,55
2,22
2,10
SPC 12,5
180-250
250-355
2,55
2,20
Johnson Controls Marine 16
355-560
>560
2,00
1,90
TO ADJUST THE DRIVE BELT TENSION USE THE TENSION SCREW ON THE SLIDE CENTRAL
3.6 DAMPERS
Dampers made of galvanised sheet metal needs levers greasing every 3 months, while dampers
made of aluminium only need a normal cleaning.
3.7 SPECIAL SECTION
3.8 VARIOUS CHECKS
Periodically carry out the following controls
Check if panels, doors and connections have air leakage
Check electric cable condition, especially in the humidification sections
Check possible water leakage in hydraulic circuits
PROBLEMS AND INCONVENIENCES
CAPACITY
Fluid temperature: - Check the fluid temperature.
Regulation valve: - Check power supply to valve and the operations of the valve.
Hydraulic connection: - Check the coil connection.
LOW HUMIDITY
Dirty nozzles: - Clean the nozzles.
Dirty filter: - Clean or replace the filter.
Insufficient water level: - Check the hydraulic circuit.
HIGH NOISE LEVEL
Johnson Controls Marine 17
Failed locking- damaged vibration damper- bearings for fan - motor section: - Close panel/door or
replace vibration damper, bearings.
Foreign body has entered the fan impeller: - Check and remove the foreign body.
Squealing due to ducts or air leakage from connections: - Check all joint.
PROBLEMS AND INCONVENIENCES
LOW AIR FLOW
The damper is not adjusted correctly: - Calibrate the damper.
The rotation of the fan is incorrect, belt is slipping: - Tighten the belts tension.
Dirty coils or filter: - Clean coils or filter.
Check duct work: - Clean duct work and open dampers in the duct system.
HIGH AIR FLOW
The damper is opened too much: - Calibrate the damper.
The filters are not fitted in their guide: - Check that filters are fitted correct in the guide.
Panel or inspection doors are opened: - Closed the inspection doors and panels.
Check duct system: - Check that all sections are calibrated correctly.
ELECTRIC MOTOR STOP
Safety device cuts motor out: - Check tension of belt.
Safety device cuts motor out: - Check that the fan impeller is not blocked.
Safety device cuts motor out: - Measure that the insulation resistance for each winding is ok.
Motor not running: - Check power supply and cable.