Download - AirPrime MC Series Dev Kit Quick Start Guide
AirPrime MC Series Dev Kit
Quick Start Guide
2130705Rev 1.5
Preface
Important Notice
Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant delays or losses of data are rare when wireless devices such as the Sierra Wireless modem are used in a normal manner with a well-constructed network, the Sierra Wireless modem should not be used in situations where failure to transmit or receive data could result in damage of any kind to the user or any other party, including but not limited to personal injury, death, or loss of property. Sierra Wireless accepts no responsibility for damages of any kind resulting from delays or errors in data transmitted or received using the Sierra Wireless modem, or for failure of the Sierra Wireless modem to transmit or receive such data.
Safety and Hazards
Do not operate the Sierra Wireless modem in areas where blasting is in progress, where explosive atmospheres may be present, near medical equipment, near life support equipment, or any equipment which may be susceptible to any form of radio interference. In such areas, the Sierra Wireless modem MUST BE POWERED OFF. The Sierra Wireless modem can transmit signals that could interfere with this equipment.
Do not operate the Sierra Wireless modem in any aircraft, whether the aircraft is on the ground or in flight. In aircraft, the Sierra Wireless modem MUST BE POWERED OFF. When operating, the Sierra Wireless modem can transmit signals that could interfere with various onboard systems.
Note: Some airlines may permit the use of cellular phones while the aircraft is on the ground and the door is open. Sierra Wireless modems may be used at this time.
The driver or operator of any vehicle should not operate the Sierra Wireless modem while in control of a vehicle. Doing so will detract from the driver or operator's control and operation of that vehicle. In some states and provinces, operating such communications devices while in control of a vehicle is an offence.
Limitation of Liability
The information in this manual is subject to change without notice and does not represent a commitment on the part of Sierra Wireless. SIERRA WIRELESS AND ITS AFFILIATES SPECIFICALLY DISCLAIM LIABILITY FOR ANY AND ALL DIRECT, INDIRECT, SPECIAL, GENERAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE OR EXEMPLARY DAMAGES INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS OR REVENUE OR ANTICIPATED PROFITS OR REVENUE ARISING OUT OF THE USE OR INABILITY TO USE ANY SIERRA WIRELESS PRODUCT, EVEN IF SIERRA WIRELESS AND/OR ITS AFFILIATES HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR THEY ARE FORESEEABLE OR FOR CLAIMS BY ANY THIRD PARTY.
Notwithstanding the foregoing, in no event shall Sierra Wireless and/or its affiliates aggregate liability arising under or in connection with the Sierra Wireless product, regardless of the number of events, occurrences, or claims giving rise to liability, be in excess of the price paid by the purchaser for the Sierra Wireless product.
Rev 1.5 Apr.10 Proprietary and Confidential 3
AirPrime MC Series Dev Kit Quick Start Guide
Patents Portions of this product may be covered by some or all of the following US patents:5,515,013 5,629,960 5,845,216 5,847,553 5,878,234 5,890,0575,929,815 6,169,884 6,191,741 6,199,168 6,339,405 6,359,5916,400,336 6,516,204 6,561,851 6,643,501 6,653,979 6,697,0306,785,830 6,845,249 6,847,830 6,876,697 6,879,585 6,886,0496,968,171 6,985,757 7,023,878 7,053,843 7,106,569 7,145,2677,200,512 7,295,171 7, 287,162 D442,170 D459,303 D599,256D560,911
and other patents pending.
This product includes technology licensed from QUALCOMM® 3G.
Manufactured or sold by Sierra Wireless or its licensees under one or more patents licensed from InterDigital Group.
Copyright ©2010 Sierra Wireless. All rights reserved.
Trademarks AirCard® and Watcher® are registered trademarks of Sierra Wireless. Sierra Wireless™, AirPrime™, AirLink™, AirVantage™ and the Sierra Wireless logo are trademarks of Sierra Wireless.
Windows® and Windows Vista® are registered trademarks of Microsoft Corporation.
Macintosh and Mac OS are registered trademarks of Apple Inc., registered in the U.S. and other countries.
QUALCOMM® is a registered trademark of QUALCOMM Incorporated. Used under license.
Other trademarks are the property of their respective owners.
Contact Information
Consult our website for up-to-date product descriptions, documentation, application notes, firmware upgrades, troubleshooting tips, and press releases:
www.sierrawireless.com
Sales Desk: Phone: 1-604-232-1488
Hours: 8:00 AM to 5:00 PM Pacific Time
E-mail: [email protected]
Post: Sierra Wireless13811 Wireless WayRichmond, BCCanada V6V 3A4
Fax: 1-604-231-1109
Web: www.sierrawireless.com
4 Proprietary and Confidential 2130705
Preface
Revision History
Revision number
Release date Changes
1.2 Feb 2009 Newest UDK board; revised software installation procedure
1.3 Mar 2009 Added MC5728V.Added a column for MC5727V to Table 2-6 on page 22.Removed references to MC5720, MC5725/MC5725V.Removed QUALCOMM patents from preface.
1.4 Jul 2009 Added MC8700.Removed references to MC8755, MC8755V, MC8765V, MC8785V.Updated Table 2-6, Dev Kit—Module signal map, on page 22
1.5 Apr 2010 Added MC8201 and MC8795V.New template/branding.
Rev 1.5 Apr.10 Proprietary and Confidential 5
AirPrime MC Series Dev Kit Quick Start Guide
6 Proprietary and Confidential 2130705
Rev 1.5 Apr.10 Proprietary and Confidential 7
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Required equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Setup and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Hardware setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Insert a SIM card (UMTS Mini Cards only) . . . . . . . . . . . . . . . . . . . . . . .13
Insert the Mini Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Connect the antenna(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Connect the power supply and USB cable . . . . . . . . . . . . . . . . . . . . . . .17
Remove/replace the Mini Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Connect the Dev Kit and host device using a Mini Card Host Extender .17
Configure the Mini Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Install / update Mini Card drivers and Watcher . . . . . . . . . . . . . . . . . . . . . . 22
Download CDMA installer package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Download UMTS installer package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Install CDMA or UMTS software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Schematic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
AirPrime MC Series Dev Kit Quick Start Guide
8 Proprietary and Confidential 2130705
Rev 1.5 A
1
1: IntroductionThis quick start guide explains how to set up the hardware and software components of Sierra Wireless’ PCI Express Mini Card Dev Kit for use with the modules listed in Table 1-1.The Dev Kit will also be used for forthcoming CDMA and UMTS Mini Card modules. (Older Mini Cards may also be supported.)
Table 1-1: Supported AirPrime Mini Cardsa
a. Throughout this document, MC57xx and MC8xxx refer to the listed suites of CDMA and UMTS Mini Cards respec-tively.
Network Mini Cards
CDMA (MC57xx) MC5727MC5727VMC5728V
UMTS (MC8xxx) MC8201MC8700MC8775MC8775VMC8780MC8781MC8790MC8790VMC8791VMC8792VMC8795V
pr.10 Proprietary and Confidential 9
AirPrime MC Series Dev Kit Quick Start Guide
Required equipment
Table 1-2 details the items required to begin using the Dev Kit in your development environment. If any items are missing from the Dev Kit, contact your Sierra Wireless representative.
Table 1-2: Required equipment
Item Included in Dev Kit
Details
Drivers & Watcher software
No Watcher software and Mini Card device drivers for the following operatirng systems may be downloaded from www.sierrawireless.com/minicard:
• Windows XP Pro (SP3) and higher
• Windows Vista (SP1) and higherRegistration is required to download these and other files.
Mini Card No The Dev Kit supports the Mini Cards listed in Table 1-1 on page 9 (purchased separately).
Antenna kit Yes The antenna kit includes 2 each of:
• Antenna
• Antenna connector
• Sample / replacement Molex connector
• Connecting wire
Audio headset Yes
Antenna connector
removal tool
Yes
PCI Express Mini Card Dev Kit
Yes The Mini Card is inserted into the Dev Kit for testing and development.
10 Proprietary and Confidential 2130705
Introduction
Power supply Yes Universal power supply, suitable for both 120 V and 240 V
UART cable Yes D-sub9 (male) to D-sub9 (female)
USB cable Yes Standard USB-A to USB-B cable
SIM/USIM card No (UMTS only) You need to supply a SIM/USIM with an active account for use with UMTS Mini Cards.
Flat flex cable Yes Together, these are used to connect a Mini Card to a laptop via the Dev Kit.
Mini Card host extender
Yes
Table 1-2: Required equipment (Continued)
Item Included in Dev Kit
Details
Rev 1.5 Apr.10 Proprietary and Confidential 11
AirPrime MC Series Dev Kit Quick Start Guide
12 Proprietary and Confidential 2130705
Rev 1.5 A
2
2: Setup and InstallationTo begin using the Dev Kit with your development system, set up your hardware and software:• Hardware setup· Insert a SIM card (UMTS Mini Cards only) on page 13· Insert the Mini Card on page 15· Connect the antenna(s) on page 16· Connect the power supply and USB cable on page 17· Connect the Dev Kit and host device using a Mini Card Host
Extender on page 17
• Software setup (CDMA)· Install / update Mini Card drivers and Watcher on page 22
Hardware setup
Insert a SIM card (UMTS Mini Cards only)
Note: Throughout this document, ‘SIM’ refers to ‘SIM’ and ‘USIM’.
To use a UMTS Mini Card (MC8xxx), you need to install:
• A live SIM card (with an active account), or
• A test SIM card for use with a call box (for example, an Agilent 8960 or Rohde&Schwarz CMU200)
To install the SIM card:
1. Place the Dev Kit face-up (as shown)—the SIM slot is on the left side beside the USB plug and the black banana plug.
Figure 2-1: SIM slot location
pr.10 Proprietary and Confidential 13
AirPrime MC Series Dev Kit Quick Start Guide
2. Open the SIM casing—push the SIM slot cover into the ‘OPEN’ position (in the direction of the ANALOG HEADER), and then lift it.
Figure 2-2: Opening the SIM cover
3. Insert the SIM card into the cover with its circuitry face-down—note the location of the notched corner of the card in the following image.
Figure 2-3: Inserting a SIM into the open cover
4. Lower the SIM slot cover—the cover (with the card inside) will be slightly raised (not making contact with the board).
5. Gently press down on the cover and then slide the slot cover under the connector base latches into the ‘CLOSED’ position—the cover locks into place.
Figure 2-4: SIM inserted with cover closed
14 Proprietary and Confidential 2130705
Setup and Installation
Insert the Mini Card
After inserting the SIM card, insert the Mini Card:
1. Place the Dev Kit face-up (as shown)—the Mini Card slot is in the top right corner.
Figure 2-5: Mini Card slot
2. Hold the Mini Card at the screw holes and slide it into the Dev Kit’s Mini Card slot at a 45 angle (inserting it ‘flat’ may damage the module’s contacts and wear out the host connector).
Figure 2-6: Inserting a Mini Card
3. Push the free end of the Mini Card down until it clicks into the black MINIPCI-E latch.
Figure 2-7: Locking a Mini Card into the Dev Kit
Rev 1.5 Apr.10 Proprietary and Confidential 15
AirPrime MC Series Dev Kit Quick Start Guide
Connect the antenna(s)
After installing the Mini Card, connect the supplied antenna(s) to the Dev Kit (some Mini Cards include both a main and an auxiliary (diversity/gps) antenna):
1. Place the Dev Kit face-up. The antenna connectors are on the right side near the top.
2. Screw the silver adapter onto the Dev Kit’s main antenna connector.
Figure 2-8: Connecting the antenna adapter
3. Connect the Mini Card’s main antenna to the Dev Kit’s main antenna connector using the gray wire provided—press down lightly on the connector ends. (The first few times you use these connectors, they may be quite snug—press straight down on the end to get a secure connection.)
Figure 2-9: Connecting the antenna wire
4. Connect the antenna to the adapter. (The first few times you attach the antenna, it may be quite snug.)
Figure 2-10: Connecting the antenna
5. If your Mini Card supports a second antenna (diversity or gps), repeat Step 2–Step 4 for the second antenna.
16 Proprietary and Confidential 2130705
Setup and Installation
Connect the power supply and USB cable
To install the power supply and USB cable:
1. Place the Dev Kit face-up.
2. Insert one end of the USB cable into the USB connector (beside the SIM slot)—you will connect the other end to your development computer later (DO NOT connect it yet).
3. Insert the power supply into the Dev Kit’s power supply connector (below the red banana plug, to the left of the UART1 connector)—the other end connects to a standard power outlet.
Remove/replace the Mini Card
When you want to remove or replace the Mini Card:
1. Place the Dev Kit face-up.
2. Remove the connecting wire(s) from the Mini Card’s antenna(s)—use the connector tool, hook it under the RF connector and pull straight up.
Figure 2-11: Removing the antenna wire
3. Holding the Dev Kit firmly in place, pull both arms of the MINIPCI-E latch at the same time toward the antenna connectors to release the module.
4. Pull the Mini Card out of the slot at a 45 angle.
Connect the Dev Kit and host device using a Mini Card Host Extender
To test the Mini Card integrated with the host device, use the Mini Card Host Extender and flat flex cable to connect the Dev Kit board and the host device:
1. Prepare the Dev Kit as normal—insert the SIM (for UMTS modems), insert the Mini Card, and attach the antenna. (You can do these steps at any time in this procedure.)
2. Insert the Mini Card Host Extender in your host device in the same way that you would insert the actual Mini Card.
Note: For simplicity, the images in this example show the Mini Card Host Extender unattached.
Rev 1.5 Apr.10 Proprietary and Confidential 17
AirPrime MC Series Dev Kit Quick Start Guide
3. Insert one end of the flat flex cable (pins facing up) into any of the three connectors on the Mini Card Host Extender:
a. Push the cable forward, between the tabs of the brown clip on the connector. As you move the cable forward, you will feel some slight resis-tance as it moves into the connector and the clip tilts slightly upward.
Figure 2-12: Attaching a host extender to a Mini Card
b. When the cable is seated firmly in the connector, push down on the arms of the brown clip to lock the connector in place.
4. Insert the other end of the flat flex cable into connector CN9 on the Dev Kit board using the same method.
Figure 2-13: Attaching a host extender to the Dev Kit
To disconnect the flat flex cable from the Mini Card Host Extender or Dev Kit board:
1. Pull up on both arms of the brown clip on the connector at the same time to release the cable.
2. Pull the flat flex cable straight out of the connector.
Configure the Mini Card
The Dev Kit includes several switches and jumpers that you can use to configure the Mini Card’s operation, as detailed in Table 2-1 on page 19 through Table 2-5 on page 21, and Figure 2-15 on page 21. For a detailed schematic of the kit, see Schematic diagram on page 25.
Note: Some Dev Kit features are available for certain Mini Cards only. For example, the Audio and UART features are only available for voice-enabled Mini Cards.
18 Proprietary and Confidential 2130705
Setup and Installation
Figure 2-14: Dev kit switches and jumpers
USB port
GND banana plug port
+3.3V banana plug port
+5V barrel jack power
Main UART D-sub9
Secondary UART D-sub9
VCC_3.3V adjust
SW4 power control
CN8 power routing options
Diversity RF SMA connector
Mini Card connector
SW1 LED/UART control
Main RF SMA connector
RESET switch
CN9 host adapter flex
SW3 audio control
CN18 analog header
USIM/RUIM card socket
Headset jack
CN25 board power select
Table 2-1: CN25—Board power (+5 V) selecta
a. Required: Select one option only (Jump 1–2 or Jump 5–6)
FunctionJump 1–2
Jump
3–4b
b. Pins 3 and 4 are not used
Jump 5–6
Power supplied by USB cable (through CN1–USB port)
Yes
Power supplied from Wall cube brick (through CN2–barrel jack power)
Yes
Table 2-2: CN8—Power routing optionsab
a. Required: Select either Jump 1–2 or Jump 3–4b. Jump 5–6 is optional—use only as needed
FunctionJump 1–2
Jump
3–42Jump 5–6
Enable onboard LDO to supply VCC_3.3V power from USB cable or wall cube (see Table 2-1 on page 19 for details)
Yes
Host Adapter Flex supplies VCC_3.3V Yes
Enable supercapacitor in circuit on VCC_3.3V node (useful for UMTS Mini Cards)
Yes
Rev 1.5 Apr.10 Proprietary and Confidential 19
AirPrime MC Series Dev Kit Quick Start Guide
Table 2-3: SW3—Audio controla
Function Dip1 Dip2 Dip3 Dip4
+20 dB gain on MIC1P On Off
+0 dB gain on MIC1P Off On
+20 dB gain on MIC1N On Off
+0 dB gain on MIC1N Off On
a. For line-level audio devices such as TTY consoles, we recom-mend setting 0 dB MIC gain.
Table 2-4: SW1—LED / UART control
Function /(Label on board)
Dip On / Off State
Headset detect(EN HEADSET DET)
1 On Enable headset detect
Off (Default) Disable headset detect
Button detect(EN BUTTON DET)
2 On Enable button detect
Off (Default) Disable button detect
Green LED(EN GRN LED)
3 On Enable green LED
Off (Default) Disable green LED
Red LED(EN RED LED)
4 On Enable red LED
Off (Default) Disable red LED
MIO LEDs(EN MIO LEDS)
5 On Enable MIO LEDsEnable for voice modems (High = Led ON)
Off Disable MIO LEDsDisable for data modems
UART1 flow control(EN UART1 RTS/CTS)
6 On Enable RTS / CTS lines of UART1 (voice modules can be configured to support this function)
Off Disable RTS / CTS lines of UART1
UART1 signals(EN UART1 RI/CD/DTR/DSR)
7 On Enable CD / DTR / DSR / RI of UART1
Off Disable CD / DTR / DSR / RI of UART1
UART1 main transceiver(EN UART1 XCVR)
8 On Enable UART1 transceiver
Off Disable UART1 transceiver
UART3 secondary transceiver(EN UART3 XCVR)
9 On Enable UART3 transceiver
Off Disable UART3 transceiver
20 Proprietary and Confidential 2130705
Setup and Installation
Figure 2-15: Audio test headers
Disable modem(DISABLE MODEM)
10 On Disable modemAssert (modem powerdown command)
Off Enable modemDe-assert (modem power up)
Table 2-5: SW4—Power control
Function Dip On / Off State
VCC_3.3V 1 On (Default) Fixed regulation from USB power or wall cube power at 3.30 V
Off Adjustable regulation from USB power or wall cube power at 3.30 V
2 On Enable onboard LDO (Low Drop Out) regulation of power from USB or wall cube
Off Disable onboard LDO
VCC_MSM26_DIGa
Note: Pins 3 and 4 must NOT be ON at the same time.
3 On (Default) Supplied by modem
Off Not supplied by modem
4 On Supplied by Dev Kit
Off Not supplied by Dev Kit
a. Required for voice-enabled modems; not required for data modems.Default setting for non-voice modems is Dip3–On and Dip4–Off.
Table 2-4: SW1—LED / UART control (Continued)
Function /(Label on board)
Dip On / Off State
Rev 1.5 Apr.10 Proprietary and Confidential 21
AirPrime MC Series Dev Kit Quick Start Guide
Install / update Mini Card drivers and Watcher
The most recent CDMA and UMTS Mini Card software installation packages (drivers, and Watcher for Windows XP Professional and Windows Vista) are available from www.sierrawireless.com/minicard (registration is required).
If necessary, contact [email protected] for assistance, or to order the software on CD.
Download CDMA installer package
To download the CDMA Mini Card software installation package:
1. In your browser, go to www.sierrawireless.com/minicard (registration required).
2. Click the Docs & FW tab.
3. Click the EM/MC5xxx CDMA Firmware link.
4. Click the Watcher Versions link.
5. Click the most recent Watcher link.
6. When prompted, save the installer package to a local folder.
Table 2-6: Dev Kit—Module signal mapa
Pinb MC5727V MC5728V
MC5727MC8775MC8780MC8781MC8790MC8700
MC8201 MC8775V
MC8790VMC8791VMC8792VMC8795V
MIO6 GPIO32 GPIO3 NC GPIO_1 GPIO_1 GPIO_1
MIO16 GPIO84 GPIO21 NC GPIO_2 GPIO_2 GPIO_2
MIO28 GPIO85 GPIO20 NC GPIO_3 GPIO_3 GPIO_3
MIO30 GPIO27 GPIO19 NC GPIO_4 NC GPIO_4
MIO32 GPIO26 GPIO18 NC NC NC RI
MIO44 GPIO31 GPIO7 NC NC GPIO_4 DCD/GPIO_4
MIO46 GPIO30 GPIO2 NC NC GPIO_5 DSR/GPIO_5
MIO48 GPIO18 GPIO15 NC NC GPIO_6 DTR/GPIO_6
a. ‘GPIO*’—Firmware-assigned signal names.b. ‘MIO’—Multi-purpose I/O. These are the physical pins on the module.
22 Proprietary and Confidential 2130705
Setup and Installation
Download UMTS installer package
To download the UMTS Mini Card software installation package:
1. In your browser, go to www.sierrawireless.com/minicard (registration required).
2. Click the Docs & FW tab.
3. Click the MC87xx GSM Firmware link.
4. Click the 3G Watcher and Drivers link.
5. Click the 3G Watcher Builds link.
6. Click the link for the most recent Watcher installer package (the File Type is MSI).
7. When prompted, save the installer package to a local folder.
Install CDMA or UMTS software
After downloading the appropriate installer package (CDMA or UMTS):
1. Run the installer package (.msi file). If the InstallShield Wizard window for Watcher appears, go to Step 2. Otherwise, if the Program Maintenance window appears, you have to remove an earlier version of Watcher before continuing:
a. Select Remove and click Next.
b. Click Remove. A window appears, showing the progress of the uninstall process, and then the InstallShield Wizard window appears when the uninstall is complete.
c. Click Finish.
d. Repeat Step 1 to install the new Watcher software.
2. The InstallShield Wizard Watcher Welcome window appears.
3. Click Install (CDMA) or Next (UMTS). The License Agreement appears.
4. Read the agreement, and then select I accept the terms in the license agreement.
5. Use the default folder (or click Change to select a different folder), and then click Next (CDMA) or Install (UMTS). A window appears, showing the progress of the installation process, and then the installation completed window appears.
6. Click Finish.
Rev 1.5 Apr.10 Proprietary and Confidential 23
AirPrime MC Series Dev Kit Quick Start Guide
24 Proprietary and Confidential 2130705
Rev 1.5 A
A
A: Schematic diagramNote: Table 2-6 on page 22 provides a cross-reference for signal names that differ between the various modules’ product specification documents.Figure 1-1: Dev Kit schematic diagram (page 1 of 2)
RF
1R
F2
UA
RT
1_D
TR
_DS
R_C
D_
RI_
EN
RI1
XIM
_IN
DT
R
HS
_B
UT
TO
N_
N
HS
_DE
TE
CT
_N
0.1V
ref
1.0V
ref
2500
152
Min
iCar
d D
ev K
it
1 O
F 2
MIN
I C
AR
D D
EV
KIT
25001521
02-
05-
2008
CI
Thi
s do
cum
ent c
ont
ain
s in
form
atio
n w
hich
is
pro
prie
tary
and
co
nfid
ent
ial t
o S
ierr
a W
irele
ss
Inc.
Dis
clo
sure
to P
erso
ns
oth
er th
an
the
offic
ers,
em
ploy
ees,
ag
enst
or
subc
ontr
acto
rsof
the
com
pan
y or
lice
nsee
of t
his
docu
me
nt
with
out t
he
prio
r w
ritte
n pe
rmis
sio
n o
f Sie
rra
W
irele
ss In
c. is
str
ictly
pro
hib
ited.
Cop
yrig
ht (
C)
2004-2008
NO
NE
D
TIT
LE
:A
PP
RO
VA
LSD
ATE
PR
OJE
CT
:
DR
AW
N:
CH
EC
KE
D:
EN
GIN
EE
R:
SIZ
E
SC
AL
E:
FS
CM
NO
.D
WG
. N
O.
SH
EE
T:
SC
HE
MA
TIC
DIA
GR
AM
,
SH. DWG. NO.
AP
PR
OV
ED
DA
TE
DE
SC
RIP
TIO
NR
EV
RE
VIS
ION
S
12
34
56
78
ABCD
87
65
43
21
D C A
Sie
rra
Wire
less
PR
IMA
RY
RF
INTE
RFA
CE
CN
16U
.FL
-R-S
MT
10
9650
-111
3-0
17
CN
17
SE
CO
ND
AR
Y R
F IN
TE
RF
AC
EC
N14 U
.FL
-R-S
MT
10
965
0-1
113-
017
CN
15
C12
22pFDNI
C8
22pFDNI
XIM
_CLK
R14
60
R14
70
R1
480
R1
490
XIM
_IO
XIM
_RE
SE
T
VC
C_
2.6V
DIP
SW
ITC
HE
S
219
-10M
ST
P
SW
1
0ohms
R165
W_
DIS
AB
LE_N
EN
AB
LE_U
AR
T3
RE
SE
T_
N
EN
AB
LE_U
AR
T1
HO
ST
AD
AP
TE
R F
LEX
CN
9
FH
12A
-50S
-0.5
SH
VC
C_
2.6V
CT
S1
_XC
VR
RX
D1
TX
D1
RT
S1
_XC
VR
R386
100K
EN
AB
LE
_U
AR
T1
MIC
1_P
MIC
1_N
SP
K1_
P
SP
K1_
NC
TS
1_N
RT
S1
_N
RX
D1
TX
D1
MIO
6
XIM
_IO
XIM
_CL
K
XIM
_R
ES
ET
MIO
16
W_
DIS
AB
LE_N
AU
XV
1M
IO28
MIO
30
MIO
32
US
B-
US
B+
WW
AN
_LE
D
MIO
44
MIO
46
MIO
48
U1
1
MA
X32
38E
EA
I+T
UA
RT
1 X
CV
R
CN
11
574
784
4-2
1uF
C42
1uF
C43
1uF
C44
1uF
C45
MA
X32
38E
EA
I+T
U12
UA
RT3
XC
VR
5747
844
-2
CN
12
EN
AB
LE
_U
AR
T3
100K
R166
1uF
C4
6
1uF
C47
1uF
C48
1uF
C49
MIO
16
MIO
28
RE
SE
T_N
TP
33T
ES
TP
OIN
T_0
100
_R
ND
TP
34T
ES
TP
OIN
T_0
100
_R
ND
CN
10
SI-
583-
1HE
AD
SE
T JA
CK
2.5
MM
TC
74L
CX
125
FT
U1
7
C52
33u
F
MIO
48
VC
C_
2.6V
MIO
32
MIO
44
C5
3
0.1u
FC
57
0.0
1uF
C61
0.1u
F
C6
2
0.1
uF
C6
3
0.01
uF
C64
0.01
uF
C65
0.1uF
C66
0.01uF
33u
FC
67S
PK
1_P
SP
K1
_NM
IC1
P_
IN
MIC
1N
_IN
600o
hms
L1
600o
hms
L2
600o
hms
L3
600o
hms
L4
WW
AN
_LE
DLE
D_G
RN
LED
_RE
DE
MB
ED
DE
D_
LED
S_N
SML-310MTT86D31
SML-310LTT86D32
200o
hms
R18
3
200
ohm
s
R1
84
LED
_GR
N
LED
_R
ED
UA
RT
1_R
TS
_CT
S_E
N
MIO
46
R185
10K
R186
10K
R188
10K
R189
10K
U20
XC
620
4B
262M
R
ON
BO
AR
D 2
.6V
LD
O C68
1uF
C69
1uF
VC
C_L
DO
26_D
IGV
CC
_3.
3V
R20
5
0
DN
IR
TC
K
R20
6
0
DN
IT
DO
R20
7
0
DN
IT
CK
R20
8
0
DN
IT
MS
R20
9
0
DN
IT
DI
TR
ST
_N
R21
0
0
DN
I
R21
1
0
U2
1
TC
74L
CX
125
FT
UA
RT
1_R
TS
_C
TS
_EN
C7
0
0.1u
F
C7
1
0.0
1uF
CT
S1_
XC
VR
CT
S1
_N
RT
S1
_XC
VR
RT
S1_
N
TP
40
TP
41
TP
42T
P4
3
R212
1K
VC
C_2
.6V
R213
10KR214
10K
R21
5
1K
R21
6
1K
R21
7
1K
R2
18
1K
C73
4.7uF
C74
4.7uF
FTZ5_6E
D33
FTZ5_6E
D33
FTZ5_6E
D33FTZ5_6E
D33
0
R22
4
VC
C_
2.6V
MIO
28M
EG
A_
CM
D
R227
10K
R2
30
0oh
ms
R2
31
0ohm
s
R23
2
0ohm
s
R2
33
0oh
ms
SW
2
B3S
-10
02
PU
SH
-BU
TTO
N R
ES
ET
W_D
ISA
BL
E_N
R242
1M
R243
100K R244
100K
VC
C_2
.6V
VC
C_
2.6V
LMC
7101
AIM
5 N
OP
B
U25
LMC
7101
AIM
5 N
OP
B
U24
MIO
44
MIO
46
1%60.4K
R258
6.2K
R259
1%100K
R260
100K
R26
1
100K
R2
62
0.0
1uFC
82
0.01
uFC8
3
0.01uF
C84
0.01uF
C85
0.01uF
C86
0.01uF
C87
22pF
C88
22pF
C8
9
Q1
NS
BC
144
ED
XV
6T1
Q1
NS
BC
144
ED
XV
6T1
BA
S16
XV
2T1
D34
0 R
226
DN
I
MIO
48M
EG
A_C
LK
0 R
145
MIO
16M
EG
A_
DA
TA
CN
27
TF
-F-8
P-M
-E10
00
Mic
ro S
D
CD
1C
D2
MIO
44S
D_C
LK
MIO
46S
D_
CM
D
MIO
6S
D_
DA
TA
R1
250 0
R1
26
0 R
127
SD
SC
DA
6A01
01
CN
20
0
R121
DN
I
VC
C_3
.3V
R144
0
VC
C_2
.6V
10K
R122
1K
R12
8
R12
9
1K
R123
10K
MIO
16
MIO
28
SIM
CO
NN
EC
TO
R
2540
21M
A00
8G1
00Z
L
CN
13
DIP
1 :
ON
= E
N H
EA
DS
ET
DE
T;
OF
F=
DIS
HE
AD
SE
T D
ET
DIP
2 :
ON
= E
N B
UT
TO
N D
ET
; O
FF
=D
IS B
UT
TO
N D
ET
DIP
3-4
: O
N O
N S
ET
BIC
OLO
R W
AN
LE
D M
OD
E D
IP3
-4 :
OF
F O
FF
-D
IS W
AN
LE
D D
IP3
-4 :
ON
OF
F -
SE
T O
PE
N D
RA
IN W
AN
LE
D M
OD
E (
GR
N)
DIP
3-4
: O
FF
ON
-S
ET
CM
OS
WA
N L
ED
MO
DE
(R
ED
)D
IP5
: O
N =
EN
MIO
LE
DS
, OF
F=
DIS
MIO
LE
DS
DIP
6 :
ON
=E
N U
AR
T1
RT
S/C
TS
; O
FF
=D
IS U
AR
T1
RT
S/C
TS
DIP
7 :
ON
=E
N U
AR
T1
RI/C
D/D
TR
/DS
R O
FF
= D
IS U
AR
T1
RI/
CD
/DT
R/D
SR
DIP
8 :
ON
=E
N U
AR
T1
XC
VR
, O
FF
=D
IS U
AR
T1
XC
VR
DIP
9 :
ON
= E
N U
AR
T3
XC
VR
, OF
F=
DIS
UA
RT
3 X
CV
RD
IP10
: ON
= D
ISA
BLE
MO
DE
M,
OF
F=
EN
AB
LE M
OD
EM
DT
R1_
RS
232
RI1
_RS
232
CD
1_R
S23
2
DS
R1
_RS
232
Initi
al R
elea
se0
2-05
-20
08
AU
X_
PC
M_
CLK
AU
X_P
CM
_DIN
AU
X_
PC
M_
DO
UT
AU
X_P
CM
_SY
NC
RX
D1_
RS
232
CT
S1
_RS
232
TX
D1
_RS
232
RT
S1
_RS
232
1.0
pr.10 Proprietary and Confidential 25
AirPrime MC Series Dev Kit Quick Start Guide
Figure 1-2: Dev Kit schematic diagram (page 2 of 2)
02-
05-
2008
2 2500152
MIN
I C
AR
D D
EV
KIT 2
OF
2
Min
iCar
d D
ev K
it
CI
250
0152
Thi
s do
cum
ent c
ont
ain
s in
form
atio
n w
hich
is
pro
prie
tary
and
co
nfid
ent
ial t
o S
ierr
a W
irele
ss
Inc.
Dis
clo
sure
to P
erso
ns
oth
er th
an
the
offic
ers,
em
ploy
ees,
ag
enst
or
subc
ontr
acto
rsof
the
com
pan
y or
lice
nsee
of t
his
docu
me
nt
with
out t
he
prio
r w
ritte
n pe
rmis
sio
n o
f Sie
rra
W
irele
ss In
c. is
str
ictly
pro
hib
ited.
Cop
yrig
ht (
C)
2004-2008
NO
NE
D
TIT
LE
:A
PP
RO
VA
LSD
ATE
PR
OJE
CT
:
DR
AW
N:
CH
EC
KE
D:
EN
GIN
EE
R:
SIZ
E
SC
AL
E:
FS
CM
NO
.D
WG
. N
O.
SH
EE
T:
SC
HE
MA
TIC
DIA
GR
AM
,
SH. DWG. NO.
AP
PR
OV
ED
DA
TE
DE
SC
RIP
TIO
NR
EV
RE
VIS
ION
S
12
34
56
78
ABCD
87
65
43
21
D C A
Sie
rra
Wire
less
MIO
32
US
B+
RT
CK
TD
OT
CK
TM
ST
DI
TR
ST
_N
RT
S1_
N
TX
D1
CT
S1
_N
RX
D1
SP
K1_
PS
PK
1_N
MIC
1_P
MIC
1_N
W_D
ISA
BLE
_N
WW
AN
_LE
D
SW
4
219-
4M
ST
P
1%
R81
100K
U23
MIC
AM
P +
LP
F
AU
DIO
GA
IN S
TA
GE L
MC
7101
AIM
5 N
OP
B
MIC
1_P
MIC
1_N
CN
8T
SM
-103
-01-
L-D
V-M
-TR
CN
5
TS
M-1
10-0
1-L
-DV
C200
1uF
TP
201
5006
TP
202
500
6
XIM
_IO
XIM
_CL
KX
IM_
RE
SE
T
MIC
1P
_IN
MIC
1N_I
N
TR
ST
_NT
DI
TM
ST
CK
RE
SE
T_
N
RT
CK
TD
O
6791
0-0
001
CN
3
R102100K
D4
CM
S01
BA
RR
EL
JAC
K L
DO
U7
MIC
293
02W
U
RT
CK
TD
O
TC
KT
MS
TD
I
TR
ST
_NR
ES
ET
_N
VC
C_
5V
R113
10K
CN
2
RA
PC
712
X
5V J
AC
K
292
304-
1
CN
1
US
B C
ON
N
US
B+
US
B-
US
B-
430ohms
R124
22pF
C2
05
0.02
2uF
C2
06
0.001uF
C207
Fc
= 3
.39k
Hz
0.01
uF
C2
04
0.1uF
C209
0.1uF
C210
10K
R204
100K
R200
100K
R201
100K
R202
100K
R203
1%60.4K
R82
HS
201M
C21
1
Fle
x co
nnec
tor
plac
ed to
psi
de o
f bo
ard
CN
6
5274
5-10
96
RE
SE
T_
N
10V
C37
10uF
10V
C38
10uF
C39
10uF
C40
10uF
C41
10uF
MIO
6
MIO
16
AU
XV
1
CN
7
TS
M-1
10-0
1-L-
DV
DIG
ITA
L H
EA
DE
R
AU
XV
1
MIO
28M
IO30
MIO
44M
IO46
MIO
48
CT
S1
_NR
TS
1_N
RX
D1
TX
D1
TC
74L
CX
125
FT
U14
TC
74L
CX
125F
T
U1
5
330o
hm
s
R1
67
330o
hm
s
R1
68
330o
hm
s
R1
69
330o
hm
s
R1
70
330
ohm
s
R1
71
330
ohm
s
R1
72
330
ohm
s
R1
73
330
ohm
s
R1
74
330
ohm
s
R17
5
100
R17
6
100K
R177
EM
BE
DD
ED
_LE
DS
_N
EM
BE
DD
ED
_LE
DS
_N
EM
BE
DD
ED
_LE
DS
_N
MIO
6
MIO
16
MIO
28
MIO
30
MIO
32
MIO
44
MIO
46
MIO
48
MIO
6M
IO1
6M
IO2
8M
IO3
0
MIO
32M
IO4
4M
IO4
6M
IO4
8
XIM
_IO
XIM
_CLK
XIM
_R
ES
ET
SP
K1_
PS
PK
1_N
MIC
1_P
MIC
1_N
D1
3S
ML-
310M
TT
86
D1
4S
ML
-310
MT
T86
D15
SM
L-31
0MT
T86
D16
SM
L-31
0MT
T86
D17
SM
L-31
0MT
T86
D18
SM
L-31
0MT
T86
D19
SM
L-3
10M
TT
86
D20
SM
L-3
10M
TT
86
D21
SM
L-3
10M
TT
86
D22
SM
L-3
10M
TT
86
D23
SM
L-3
10M
TT
86
D24
SM
L-31
0MT
T86
D25
SM
L-31
0MT
T86
D26
SM
L-31
0MT
T86
330
ohm
s
R17
8
330
ohm
s
R17
9
330
ohm
s
R18
0
330
ohm
s
R18
1
TC
74L
CX
125F
T
U1
6
EM
BE
DD
ED
_LE
DS
_N
VC
C_
3.3V
RX
D1
TX
D1
RT
S1
_N
CT
S1
_N
1SMA12AT3
D27
C5
4
0.1u
F
C55
0.1u
F
C56
0.1
uF
C58
0.01
uF
C5
9
0.0
1uF
C60
0.01
uF
F1
181
2L15
00
CN
25
TS
M-1
03-
01-L
-DV
-M-T
R
4809
9-00
03
CN
4
TP
38
111-
070
3-00
1
BA
NA
NA
PLU
GS
TP
3911
1-0
702
-00
1
AN
ALO
G H
EA
DE
R
TS
M-1
10-0
1-L-
DV
CN
18
219
-4M
ST
P
SW
3
MIC
1P_I
NM
IC1N
_IN
U22
LMC
710
1AIM
5 N
OP
B
C75
0.01uF
C76
22pF
R219
1Mohms
C77
0.0
22uF
R2
20
47K
ohm
s
R221
91Kohms
C78
0.001uF
R222
51Kohms
R223
10K
R2
34
100K
R235
10K
R236
1Mohms
R23
7
47K
ohm
s
R238
91Kohms
R239
51Kohms
R240
10K
R24
1
100K
5006
TP
203
5006
TP
204
100K
R245
VC
C_2
.6V
TP
205
500
6
0.1u
F
C8
0
0.1u
F
C8
1
1M
R246
1M
R247
1M
R248
1M
R249
1M R250
1M R251
1M R252
1M R253
1M R254
1M R255
1M R256
1M R257
4809
9-40
00
CN
26
DN
I
R1
400o
hm
sW
_D
ISA
BLE
_N
CN
19
TS
W-1
02-
14-
T-S
TP
26T
ES
TP
OIN
T_
0080
_RN
D
5005
TP
200
10uF
C79
10V
TS
W-1
02-1
4-T
-S
CN
21
C208
0.1uF
JMP
1-2
: L
DO
SU
PP
LIE
S 3
.3V
JMP
3-4
: H
OS
T A
DA
PT
ER
SU
PP
LIE
S 3
.3V
JMP
5-6
: S
UP
ER
CA
PA
CIT
OR
IN C
IRC
UIT
MIN
ICA
RD
SM
T C
ON
NE
CTO
RM
INIC
AR
D L
ATC
HE
S
SIG
NA
L LE
DS
AR
M9
JTA
G H
EA
DE
RS
ee S
hee
t 1
AU
X_
PC
M_
CLK
AU
X_P
CM
_DIN
AU
X_
PC
M_
DO
UT
AU
X_P
CM
_S
YN
C
AU
X_
PC
M_
SY
NC
AU
X_P
CM
_DO
UT
AU
X_P
CM
_D
IN
AU
X_P
CM
_CL
K
UA
RT
3_T
X
UA
RT
3_R
X
AR
M9
JTA
G F
LEX
CO
NN
DIP
1: O
N=
EN
FIX
ED
OU
TP
UT
MO
DE
3.3
V, O
FF
=D
IS F
IXE
D O
UT
PU
T M
OD
ED
IP2:
ON
= E
N L
DO
; O
FF
= D
IS L
DO
DIP
3: O
N=
MO
DE
M S
UP
PLI
ES
2.6
VD
IG,
OF
F=
MC
8750
DIP
4: O
N=
ON
BO
AR
D L
DO
SU
PP
LY
2.6
V (
MC
875
0 O
NLY
), E
LSE
OF
F
JMP
1-2
: U
SB
CA
BLE
PW
RJM
P 5
-6 :
BA
RR
EL
JA
CK
PW
R
DIP
1 :
ON
=E
N M
IC_
P G
AIN
+2
0dB
, O
FF
= D
IS M
IC_P
GA
IND
IP2
: O
N=
EN
MIC
_N
GA
IN +
20d
B, O
FF
= D
IS M
IC_N
GA
IND
IP3
: O
N=
EN
MIC
_P
AM
P B
YP
AS
S;
OF
F=
DIS
MIC
_P A
MP
BY
PA
SS
DIP
4 :
ON
=E
N M
IC_
N A
MP
BY
PA
SS
; O
FF
= D
IS M
IC_N
AM
P B
YP
AS
S
PW
R L
ED
S
26 Proprietary and Confidential 2130705
Rev 1.5 A
B
B: Bill of MaterialsTable B-1: Development kit bill of materialsDescription Qty Reference designators
Vendors Vendor item numbers
CONN,2.5MM,4WIRE AUDIO JACK,RT-ANGLE,SMT
1 CN10 SENIOR INDUSTRIES
SI-583-1
CONNECTOR, ULTRA-MINIATURE, RF, 3.0X3.1mm
2 CN14,CN16 HIROSE UFL-R-SMT-1(10)
IPEX 20279-001E-01
CONNECTOR, MINI PCI EXPRESS, 52PIN, 0.8MM, RIGHT ANGLE
1 CN3 MOLEX 67910-0002
ZIF, 10 PIN, 0.5MM, RIGHT ANGLE 1 CN6 MOLEX 52745-1096
CONNECTOR, 6 PIN, 2.54mm DUAL ROW
2 CN8, CN25 SAMTEC TSM-103-01-L-DV-M-TR
TESTPOINT, COMPACT, THRU-HOLE, RED PLASTIC
1 TP200 KEYSTONE 5005
TESTPOINT, COMPACT, THRU-HOLE, BLACK PLASTIC
5 TP201, TP202, TP203, TP204, TP205
KEYSTONE 5006
HEADER, JTAG, SMT, 20 PIN 3 CN5, CN7, CN18 SAMTEC TSM-110-01-L-DV
CONNECTOR, RF, EDGE MOUNT, SMA TYPE, 0.062 BOARD THICKNES
2 CN15, CN17 APPLIED ENGINEERING
9650-1113-017
CONNECTOR, 50 PIN, ZIF, 0.5MM, TOP CONTACT TYPE
1 CN9 HIROSE FH12A-50S-0.5SH(55)
CONNECTOR, 4PIN, USB, THRU, RT ANGLE
1 CN1 TYCO 292304-1
CONNECTOR, 3 PIN, 2.5MM DC POWER JACK
1 CN2 SWITCH CRAFT RAPC712X
RAPC712
CONNECTOR, LATCH, MINI PC EXPRESS
1 CN4 MOLEX 48099-0003
BINDING POST, BANANA JACK, VERTICAL, BLACK
1 TP38 JOHNSON COMPONENTS
111-0703-001
KEYSTONE 7007
BINDING POST, BANANA JACK, VERTICAL, RED
1 TP39 JOHNSON COMPONENTS
111-0702-001
KEYSTONE 7006
CONNECTOR, RECEPTACLE, D-SUB, 9PIN, RIGHT ANGLE, 0.318 SERIES
2 CN11, CN12 Amp/Tyco 5747844-2
pr.10 Proprietary and Confidential 27
AirPrime MC Series Dev Kit Quick Start Guide
CONNECTOR, SIM, 8 PIN, HINGED, 29.20x17.40x2.3mm
1 CN13 SUYIN 254021MA008G100ZL
CONNECTOR, MicroSD SOCKET, PUSH/PUSH, STANDARD, 14x16x1.88mm
1 CN27 MIT TF-F-8P-M-E1000
CAP,SUPER,3.6V, 17.5x42MM 1 C211 CAP-XX HS201K
CAP-XX HS201M
CAP-XX HS201C
CAP, CER, 10µF, 10V,20%, X5R, 0805
6 C37, C38, C39, C40, C41, C79
TAIYO YUDEN LMK212C106MG
TAIYO YUDEN LMK212BJ106KD-T
MURATA GRM21BR61A106KE19L
CAP, CER, 1µF, 10%, 6.3V, 1005, X5R
11 C42, C43, C44, C45, C46, C47, C48, C49, C68, C69, C200
MURATA GRM155R60J105KE19D
TAIYO YUDEN JMK105BJ105KV-F
CAP, TANT., 33µF, 20%, 6.3V, 3528 2 C52, C67 KEMET T520T336M006ATE070
CAP,CER,4.7µF,20%,6.3V,SM,2012,X5R
2 C73, C74 TAIYO YUDEN CEJMK212BJ475MG-T
CAP,22pF, 50V, ±5%, C0G, 1005 4 C76, C88, C89, C205
TAIYO YUDEN UMK105CG220JV-F
MURATA GRM1555C1H220JZ01D
CAP, 1000pF, 50V, ±10%, X7R, 1005 2 C78, C207 MURATA GRM155R71H102KA01D
TAIYO YUDEN UMK105BJ102KV-F
CAP, 0.01µF, 25V, ±10%, X7R, 1005 16 C57, C58, C59, C60, C63, C64, C66, C71, C75, C82, C83, C84, C85, C86, C87, C204
MURATA GRM155R71E103KA01D
TAIYO YUDEN TMK105BJ103KV-F
CAP, 0.022µF, 16V, ±10%, X7R, 1005 2 C77, C206 MURATA GRM155R71C223KA01D
TAIYO YUDEN EMK105BJ223KV-F
Table B-1: Development kit bill of materials (Continued)
Description Qty Reference designators
Vendors Vendor item numbers
28 Proprietary and Confidential 2130705
Bill of Materials
CAP, 0.1µF, 10V, ±10%, X5R, 1005 13 C53, C54, C55, C56, C61, C62, C65, C70, C80, C81, C208, C209, C210
MURATA GRM155R61A104KA01D
TAIYO YUDEN LMK105BJ104KV-F
RESISTOR, 60.4K, 1%, 1005, 1/16W, 50V, -55 +125C
2 R82, R258 ROHM MCR01MZPF6042
KOA SPEER RK73H1ETTP6042F
YAGEO RC0402FR-0760K4L
RES, 100, 5%, 1005, 1/16W, 50V, -55 +125C
1 R176 KOA SPEER RK73B1ETTP101J
YAGEO RC0402JR-07100RL
ROHM MCR01MZPJ101
RES, 200, 5%, 1005, 1/16W, 50V, -55 +125C
2 R183, R184 YAGEO RC0402JR-07200RL
KOA SPEER RK73B1ETTP201J
ROHM MCR01MZPJ201
RES, 330, 5%, 1005, 1/16W, 50V, -55 +125C
13 R167, R168, R169, R170, R171, R172, R173, R174, R175, R178, R179, R180, R181
YAGEO RC0402JR-07330RL
KOA SPEER RK73B1ETTP331J
ROHM MCR01MZPJ331
RES, 430, 5%, 1005, 1/16W, 50V, -55 +125C
1 R124 YAGEO RC0402JR-07430RL
KOA SPEER RK73B1ETTP431J
ROHM MCR01MZPJ431
RES, 1.0K, 5%, 1005, 1/16W, 50V, -55 +125C
7 R128, R129, R212, R215, R216, R217, R218
YAGEO RC0402JR-071KL
KOA SPEER RK73B1ETTP102J
ROHM MCR01MZPJ102
RES, 6.2K, 5%, 1005, 1/16W, 50V, -55 +125C
1 R259 VISHAY/DALE CRCW04026K20JNED
YAGEO RC0402JR-076K2L
KOA SPEER RK73B1ETTP622J
ROHM MCR01MZPJ622
Table B-1: Development kit bill of materials (Continued)
Description Qty Reference designators
Vendors Vendor item numbers
Rev 1.5 Apr.10 Proprietary and Confidential 29
AirPrime MC Series Dev Kit Quick Start Guide
RES, 10K, 5%, 1005, 1/16W, 50V, -55 +125C
14 R113, R122, R123, R185, R186, R188, R189, R204, R213, R214, R223, R227, R235, R240
KOA SPEER RK73B1ETTP103J
YAGEO RC0402JR-0710KL
ROHM MCR01MZPJ103
RES, 47K, 5%, 1005, 1/16W, 50V, -55 +125C
2 R220, R237 YAGEO RC0402JR-0747KL
KOA SPEER RK73B1ETTP473J
ROHM MCR01MZPJ473
RES, 91K, 5%, 1005, 1/16W, 50V, -55 +125C
4 R221, R22, R238, R239
YAGEO RC0402JR-0791KL
KOA SPEER RK73B1ETTP913J
ROHM MCR01MZPJ913
RES, 1.0M, 5%, 1005, 1/16W, 50V, -55 +125C
15 R219, R236, R242, R246, R247, R248, R249, R250, R251, R252, R253, R254, R255, R256, R257
YAGEO RC0402JR-071ML
KOA SPEER RK73B1ETTP105J
ROHM MCR01MZPJ105
RES, 0.0 Ohm, 5%, 1005, 1/16W, 50V, -55 +125C
15 R125, R126, R127, R140, R144, R146, R147, R149, R165, R211, R224, R230, R231, R232, R233
KOA SPEER RK73Z1ETTD
YAGEO RC0402JR-070RL
ROHM MCR01MZPJ000
RES, POT, 100K, 30%, 0.05W 1 R102 PANASONIC EVN-5ESX50B15
RES, 100K, 1%, 1005, 1/16W, 50V, -55 +125C
16 R81, R166, R177, R200, R201, R202, R203, R234, R241, R243, R244, R245, R260, R261, R262, R386
YAGEO RC0402FR-07100KL
ROHM MCR01MZPF1003
KOA SPEER RK73H1ETTP1003F
IC, BUFFER, QUAD, 5V TOLERANT, TSSOP-14
5 U14, U15, U16, U17, U21
TOSHIBA TC74LCX125FT(EL)
ON SEMICONDUCTOR
MC74LCX125DTG
TOSHIBA TC74LCX125FT(EL)
IC,LDO,CMOS,LOW NOISE,150mA, 2.6V
1 U20 TOREX XC6204B262MR
Table B-1: Development kit bill of materials (Continued)
Description Qty Reference designators
Vendors Vendor item numbers
30 Proprietary and Confidential 2130705
Bill of Materials
ICS, RS-232 TRANSCEIVER, LOW-POWER, ESD, -40/+85C
2 U11, U12 TEXAS INSTRUMENTS
MAX3238EIDB
MAXIM MAX3238EEAI+T
IC, OP-AMP, LOW POWER, RAIL-TO-RAIL, SOT23-5
4 U22, U23, U24, U25
NATIONAL SEMICONDUCTOR
LMC7101AIM5NOPB
IC, LDO, 3A, ADJUSTABLE, TO-263-5
1 U7 MICREL MIC29302WU
XSTR, DUAL, NPN, 47K OHM BIAS RESISTORS
1 Q1 ON SEMICONDUCTOR
NSBC144EDXV6T1
ROHM EMH2
FERRITE BEAD, 600OHM@100MHz, 1005, MULTILAYER
4 L1, L2, L3, L4 TDK MMZ1005S601CT
TDK MMZ1005S601A
KOA SPEER CZB1EGTTP601P
MURATA BLM15AG601SN1D
TAIYO YUDEN BK1005HW601
DIO, BAS16XV2T1, SWITCHING, SOD-523
1 D34 ON SEMICONDUCTOR
BAS16XV2T1G
DIO, SCHOTTKY, 3A, 30V, 3.8x2.4x1.08
1 D4 TOSHIBA CMS01
LAMP,LED,SMD,1.6x0.8,3.6mcd@20mA,GRN
15 D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23, D24, D25, D26, D31
ROHM SML-310MTT86
DIODE, ZEN,FTZ5.6, 5.6V/ 5MA,SC-74A
1 D33 ROHM FTZ5.6ET148
DIODE, TVS, 12V, 400WPEAK, SMA PACKAGE
1 D27 DIODES INC SMAJ12A-13-F
ON SEMICONDUCTOR
1SMA12AT3G
LAMP,LED,SMD,1.6x0.8,3.6mcd@20mA,RED
1 D32 ROHM SML-310LTT86
FUSE 1.5A, PTC, SLOW-BLOW 1 F1 LITTELFUSE 1812L150
SWITCH, TACT, 4 PIN 1 SW2 OMRON B3S-1002
Table B-1: Development kit bill of materials (Continued)
Description Qty Reference designators
Vendors Vendor item numbers
Rev 1.5 Apr.10 Proprietary and Confidential 31
AirPrime MC Series Dev Kit Quick Start Guide
SWITCH, DIP, 4-SPST, SEALED, MEDIUM, BLACK BODY
2 SW3, SW4 CTS 219-4MSTP
SWITCH, DIP, 10-SPST, SEALED, MEDIUM, BLACK BODY
1 SW1 CTS 219-10MSTP
Table B-1: Development kit bill of materials (Continued)
Description Qty Reference designators
Vendors Vendor item numbers
32 Proprietary and Confidential 2130705