An Evaluation of Chicken Litter Ash, Wood
Ash and Slag for Use as Lime and Phosphate
Soil Amendments
Baiq Emielda Yusiharni SP (B.Sc-Hon) in Soil Science
University of Mataram, Indonesia 2001
This thesis is presented for the degree of
Master of Science of
The University of Western Australia
School of Earth and Geographical Sciences
Faculty of Natural and Agricultural Sciences 2007
ABSTRACT
Standard AOAC methods of chemical analysis have been used to characterize and
evaluate the industrial byproducts; partly burnt chicken litter ash (CLA), totally burnt
chicken litter ash (CLAT), wood ash (WA) and iron smelting slag for use as a
combined liming agent and phosphate fertilizer. Rock phosphate has this function and
was included for comparison purposes. All the byproducts had pH values above 9 and
a liming capacity above 90% of pure lime, as a result, these materials will be effective
as liming agents. Total P concentrations for CLA, CLAT, slag, and WA were 3.6%,
4.75%, 0.26%, and 0.44% respectively indicating that they could be used as P
fertilizers when applied at the high rates required for liming soils. For all the
byproducts, citric acid (CA) dissolved phosphorus at faster rate than did neutral
ammonium citrate (NAC) and alkaline ammonium citrate (AAC). For long extraction
times total P dissolved mostly increased in the sequence CA>NAC>AAC. For no
extraction time was the P soluble in the three extractants a reliable predictor of the
effectiveness of these materials as P fertilizers which was established by plant growth
measurements. XRD and SEM analyses identified the P containing compounds and
provided explanations for the chemical analyses and dissolution behaviour. CLA,
CLAT and WA consist mostly of mixtures of apatite, calcite, and quartz although
CLA also contains much carbonised litter, which contains a low concentration of P.
Calcium magnesium silicate (akermanite) and calcium aluminium silicate (gehlenite)
were the main constituents of slag. For all apatitic materials little apatite persisted in
CA residues after 120 hours extraction but considerable apatite remained in NAC and
AAC residues.
A glasshouse experiment was carried out to identify the effectiveness of the wastes as
phosphate fertilizers for a highly P-deficient acid lateritic soil. Treatments included
various types and rates of industrial byproducts and included monocalcium phosphate,
dicalcium phosphate and rock phosphate as reference materials. Various levels of
phosphate were applied, ryegrass was planted and harvested after 8 weeks and at 4
week intervals thereafter. Dry matter yield ranged from 0.025 g to 2.3 g/pot for the
first harvest, from 0.03 g to 2.3 g/pot for the second harvest and many plants died of P
deficiency before the third harvest. The agronomic effectiveness of the materials as
phosphate fertilizers was calculated by comparing the various amounts of phosphate
i
required to produce the same yield for the various materials and relating these values
to the performance of monocalcium phosphate. This is the “horizontal comparison” or
“substitution value” procedure that gives values of Relative Effectiveness (RE) that
are independent of the rate of application of the fertilizers. The RE values for all the
materials relative to monocalcium phosphate (100%) for the first harvest are as
follows, 50% for dicalcium phosphate, 31% for rock phosphate, 7% for partly burnt
chicken litter ash, 7% for totally burnt chicken litter ash and 1% for wood ash and
slag. The RE values for the second harvest were 100% for monocalcium phosphate,
80% for dicalcium phosphate, 40% for rock phosphate, 10% for partly burnt chicken
litter ash, 8% for totally burnt chicken litter ash and 2% for wood ash and slag. Data
for subsequent harvests are not reported due to the death of many plants. Clearly
chicken litter ash has appreciable value as a phosphate fertilizer whereas wood ash
and slag are ineffective. Explanations for these differences in effectiveness are
discussed in the text.
An evaluation of the liming effect of the byproducts indicates that they may be used
as a soil amendment on acid soils and are nearly as effective as standard lime
(CaCO3). Byproducts are also sources of other plant nutrients so they may be regarded
as a form of compound fertilizer and liming agent.
ii
ACKNOWLEDGEMENTS
I would like to give my deepest thanks and appreciation to my supervisor Prof.
Bob Gilkes for his help, encouragement, and great attention during supervising my
study. I also thank Dr. Andrew Rate as my cosupervisor.
I acknowledged Australian Government (AusAID) for providing financial
support for my postgraduate research. Special thanks to Rhonda Haskell and Cathy
Tang (AusAID Liaison Officers) for being friendly and helpful in many things.
I would like to express my great appreciation to my husband, Husnan Ziadi for
helping me with laboratory and glasshouse work and especially for all his support so
that I can finish my study. Special thank to my lovely daughters, Lula and Fadila.
I also thank Michael Smirk for his assistance in solving chemical analysis
problems. Special thanks to Gary Cass and Elizabeth Halladin for lending me
laboratory equipment. Thanks to Rick Roberts and family, Cameron Duggin, Than
Hai Ngo, Geoff Kew, Georgie Holbeche, Matt Landers, Yamin Ma and Rina Barus
for being friendly and helpful.
Finally, thanks to all mineralogy group members for your friendship and for
sharing knowledge, experiences, thoughts, and laboratory equipment.
iii
LISTS OF CONTENTS
ABSTRACT i AKNOWLEDGEMENTS iii LISTS OF CONTENTS iv LIST OF TABLES vi LIST OF FIGURES vii LIST OF APPENDICES ix Chapter 1. INTRODUCTION
1.1. General Introduction 1 1.2. Objectives of the Study 2 1.3. Structure of the Thesis 2
Chapter 2. LITERATURE REVIEW 2.1. Acid Soils 3 2.2. Effect of Soil Acidity on Plants 4 2.3. Acid Soils in Australia 5 2.4. Liming Resources and Lime Requirement 7 2.5. Industrial Byproducts as Liming agents
2.5.1 Slag 9 2.5.1.1 The Nature of Industrial slag 9 2.5.1.2 Application of Slag in Agriculture 12
2.5.2 Wood Ash 13 2.5.2.1 The Nature of Industrial Wood Ash 13 2.5.2.2 Application of Wood Ash in Agriculture 16
2.5.3 Chicken Litter Ash 16 2.5.3.1 The Nature of Industrial Chicken Litter Ash 16 2.5.3.2 The Use of Chicken Litter Ash in
Agriculture 18
Chapter 3. A Laboratory Evaluation Of The Industrial Byproducts: Chicken Litter Ash, Wood Ash And Iron Smelting Slag For Use As Combined Liming Agent And Phosphorus Fertilizer
3.1. Introduction 20 3.2. Materials and Methods
3.2.1. Calcination of Chicken Litter 21 3.2.2. Industrial Byproducts 22 3.2.3. Characterisation of the Materials 22 3.2.4. Chemical Extraction of the Materials (AOAC Method) 23 3.2.5. Chemical Analysis of the Extracts 23 3.2.6. Glasshouse Experiment 24
3.3. Results and Discussion 24 3.3.1 Calcination of Chicken Litter 24
3.3.2 Dissolution of Industrial Byproducts 31 3.3.3 Relationship of Relative Agronomic Effectiveness (RE) of
CLA and CLAT with P Availability Determined by Chemical Extraction 39
3.4. Conclusions 41
iv
Chapter 4. Plant response to the byproducts: Chicken Litter Ash, Iron Smelting Slag and Wood Ash as Phosphorus Fertilizers 4.1. Introduction 42 4.2. Materials and Methods 42 4.2.1. Soil 42
4.2.2. Industrial Byproducts and Reference Fertilizers 42 4.2.3. Analysis of Industrial Byproducts and Soil 43 4.2.4. Glasshouse Experiment 43 4.2.5. Relative Agronomic Effectiveness 44
4.3. Results and Discussion 45 4.3.1. Byproduct Characterization 45 4.3.2. Soil pH, EC and Bicarbonate P 45
4.3.3. Plant Composition and Yield Response Data 47 4.3.4. Relative Effectiveness (RE) 51 4.4. Conclusions 52 Chapter 5. General Summaries, Limitation and Future Work 54 5.1. General Summary 54
5.2. Limitations and Future Works 55 Chapter 6. Publications from this thesis: 57 REFERENCES 58 APPENDICES 65
v
LIST OF TABLES
Table Page2.1.
2.2.
2.3.
2.4.
2.5.
2.6.
2.7.
2.8.
2.9.
2.10
3.1.
3.2.
3.3.
4.1. 4.2.
National and State areas (million hectares) of surface soil (0 - 10 cm) pH (measured in calcium chloride) based on information fromAustralian Soil Resources Information System (first number) andcommercial laboratories (second number).
Calcium carbonate equivalence values of some liming materials Chemical constituents of blast furnace slag (Lee 1974). Major element composition of slags (Li and Gilkes 2002). Chemical compositions of slag products used in New Zealand (Bolan2004). Mineralogical compositions of slags (Li and Gilkes 2002) Concentration of total and water-soluble plant nutrients in wood ash The chemical composition of plant ash derived from diverse species Characterisation of the chemical properties of chicken litter ash Nutrients present in Fibrophos based on the grades for Southern andCentral England/Wales The nomenclature for calcined chicken litter samples produced bycalcination at various temperatures and their pH measured in water Properties of industrial byproducts. Percentages of total phosphorus, calcium, magnesium, potassium and sodium dissolved after 1hour extraction in citrate solutions for chicken litter ash calcined at various temperatures and for Sechura rock phosphate (RP), wood ash (WA) and slag. Chemical properties of industrial byproducts and rock phosphate. Levels of P added to soil for the plant growth experiment Basal fertilizer and dose per pot used in the glasshouse experiment
6 8
10
11
11
12
14
15
17
18
21
27
32
43
44
vi
LIST OF FIGURES
Figure Page2.1.
2.2.
3.1.
3.2.
3.3.
3.4.
3.5.
3.6.
3.7.
3.8.
3.9
4.1
4.2.
4.3.
Soil pH ranges Interpolated top soil pH (1990-1999) Percentages of total P extracted from chicken litter ash produced atvarious temperatures for various durations of extraction in citric acid (A), neutral ammonium citrate (B) and alkaline ammonium citrate (C) XRD patterns of chicken litter ash calcined at various temperaturesbefore (A) and after extraction for 120 hours in citric acid (B), neutralammonium citrate (C) and alkaline ammonium citrate (C). Q = quartz (d = 3.43Ǻ), A = apatite (d = 2.84 Ǻ) Cu Kα radiation Scanning electron micrograph (SEM) and X-ray spectra of the indicated particles for 500oC calcined chicken litter (C500) before and after extraction for 120 hours in citrate solutions Percentage of P extracted from five phosphatic byproducts by threecitrate extractants for various durations of extraction XRD patterns of byproducts (A) and their residues after extraction for120 hours in citric acid (B), neutral ammonium citrate (C) and alkalineammonium citrate (D) Scanning electron micrographs (SEM) and X-ray spectra of indicated particles for original CLA and residues after extraction for 120 hours in three citrate solutions. X-ray spectrum of a carbon grain in partly burnt chicken litter ash showing that it contains minor amounts of Si, P, S, Cl, K, and Ca (A) and a silicate grain (feldspars) in totally burnt chicken litter ash containing much Si, Al, K and Ca (B). Scanning electron micrographs (SEM) and spectra of indicated grains for CLAT and residues after extraction for 120 hours in three citrate solutions. The relationship of relative agronomic effectiveness (RE) and thesolubility of P in CA for 6 hours extraction. Plots of log P applied (mg/kg) versus pH, EC, and Bic P for soil samples taken after the last harvest Yield (g/pot) versus log rate of P applied (mg/kg) for each harvest for the seven fertilizers Internal efficiency of P utilization curves for each harvest
4 6
25
28
30
33
35
36
37 38 40 46 48 49
vii
4.4. 4.5.
P content versus log P applied for all harvests RE values for the byproducts based on yield and P content for the fourharvests
50 52
viii
LIST OF APPENDICES
Appendix Page4.1.1
XRF Analysis of Plant Dry Tops for Harvest I 65
4.1.2
XRF Analysis of Plant Dry Tops for Harvest II 66
4.1.3
XRF Analysis of Plant Dry Tops for Harvest III 67
4.1.4
XRF Analysis of Plant Dry Tops for Harvest IV 68
4.2.1 Photograph showing the growth of ryegrass before the first harvest for the highest (a) and lowest (b) rates of all the fertilizers, including zero rate of application (control)
69
4.2.2 Photograph showing the growth of ryegrass before the second harvest for the highest (a) and lowest (b) rates of all the fertilizers, including zero rate of application (control).
70
4.2.3 Photograph showing the growth of ryegrass before the third harvest for the highest (a) and lowest (b) rates of all the fertilizers, including zero rate of application (control).
71
4.3
Concentration of Phosphorus in Plants Tissue 72
4.4.1
RE Values Based on P Applied and Yield for Each Harvest 73
4.4.2 RE Values Based on P Content and P Applied for Each Harvest
74
4.4.3
RE Values Based on Soil Bic P and P Applied for Each Harvest 75
ix
Chapter 1
1.0 Introduction
1.1. General Introduction
Soil acidity is a major problem worldwide as it decreases plant growth by affecting
the availability of nutrients and causes various toxicities. Acid soils may also suffer
from phosphorus, nitrogen, calcium, magnesium, potassium and other deficiencies
(Ritchie 1989; Samac and Tesfaye 2003). Acid conditions in soils cause aluminium
(Al) and manganese (Mn) to become more soluble (Slattery et al. 1999) and these
elements can be toxic to plants. Soil acidity also affects the activity of
microorganisms in soil (Robson and Abbott 1989). Acid soils are commonly deficient
in phosphate so that both conditions require correction, which can be carried out by
application of a single mineral ameliorant, which is the focus of this thesis.
Australia faces a serious problem with soil acidification. Acid soil has caused major
land degradation and has decreased plant production over several million hectares of
agricultural land in Australia (Evans, 1991). Approximately 35 million hectares of
agriculturally productive land presently have strongly acid soils (pHCa < 4.8) and 55
million hectares are fairly or slightly acid (pHCa 4.8-6.0) (Slattery et al. 1999).
Liming is the most common way to ameliorate acid soils. At some locations sources
of natural lime are inadequate or expensive. Alkaline industrial byproducts such as
metal smelting slag, wood ash and chicken litter ash may be used as replacements for
lime under these circumstances. Such byproduct materials are commonly dumped
however they may be used to ameliorate soils with consequential environmental
benefits. Some alkaline byproducts contain phosphate so that two adverse soil
conditions can be overcome by a single application of byproduct.
In contrast to the wealth of knowledge available on the nature and effectiveness of
alternative liming agent in Europe and USA, little is known of their nature,
effectiveness and availability in Australia. In particular the possibility of using lime
from industrial byproducts and mineral processing activities as soil amendments has
received little attention. Li and Gilkes (2002) mention that in 2001, almost 1 million
1
tons of lime was applied to soils in Western Australia, most of which was supplied to
farmers as natural lime, mostly as limesand and limestone from coastal areas. The
sources of those limes are likely to be inadequate in the long term and lime is
expensive in some locations. Therefore Western Australian agricultural soils might
potentially receive lime from other sources that are available locally including iron-
smelting slags, wood ash and chicken litter ash.
1.2 Objectives of this study
This study focused on the use of iron-smelting slags, wood ash and chicken litter ash,
which might be used as liming agents and to increase soil fertility on agricultural land
in Western Australia. These materials are readily available from present and planned
industrial activities in Western Australia. The study has been conducted under
laboratory, and glasshouse conditions to identify the properties of these industrial
byproducts, the effects of the addition of industrial byproducts as liming agents and
phosphate fertilizers to acid soils, together with effects on nutrient uptake, and growth
of plants.
1.3. Structure of the thesis
The organisation of this thesis consists of 5 chapters in which each chapter specifies
and discusses different aspects of the research and also discusses the related literature.
Chapter 3 and 4 have been written in journal format and these manuscripts are
currently under reviews. Justification and objectives of this research are introduced in
Chapter 1. A general literature review is given in Chapter 2. An evaluation as
phosphorus fertilizers of the byproducts: chicken litter ash, iron smelting slag and
wood ash is presented in Chapter 3. Plant response to the byproducts: chicken litter
ash, iron smelting slag and wood ash as phosphorus fertilizers is presented in Chapter
4. General discussion and conclusions, limitations of this work and suggestions for
further work are presented in Chapter 5. Tables and figures are placed within the text
and all the references cited are listed at the end of the thesis followed by the
appendices.
2
Chapter 2
2.0 Literature Review
2.1 Acid Soils
Soils become acid because of several factors. Many soils have become acid through
slow, natural processes and agricultural development can accelerate these processes
(Porter 1981; Whitney and Lamond 1993). Some soils are formed from parent
materials that are intrinsically acid and have low abundances of the alkali elements;
Ca, Mg, K and Na (Samac and Tesfaye 2003; Foy 1984). Soils containing sulphide
become very acid when drained as H2SO4 is produced (Thomas and Hargrove, 1984).
Whitney and Lamond (1993) point out that soil development processes under moist
condition generally include leaching, which together with consequences of soil
management cause soils to become acidic.
Major mechanisms of acidification of soil according to Helyar and Porter (1989)
relate to the carbon (C), and nitrogen (N) cycles. Carbonic acid results from
dissolution in soil solution of CO2 in the soil air. As water percolates through the soil,
acidification occurs as bicarbonates are leached and the hydrogen ion adsorbed and
remains. Soil can become more acid as an effect of nitrogen movement into and out of
the soil, depending on the nitrogen form that is added and on the form of nitrogen that
is removed, or accumulates (Porter 1981). The application of nitrogen fertilizers to
soils may cause a large acidifying effect. Nitrogen fertilizers contain ammonium and
soil bacteria convert ammonium (NH4+) to nitrate (NO3
+) through the nitrification
process. Hydrogen (H+) is released in this process, and free hydrogen ions cause an
increase in acidity. An important consequence of acidification is the replacement of
calcium, magnesium, potassium, and sodium (basic cations) on the soil cation
exchange complex by hydrogen, manganese, and aluminium (acidic cations) (Spies
and Harms 2004).
The acidity of a soil can be measured through its pH value, which may be taken to be
the pH of water in equilibrium with the soil (i.e. the soil solution). Soil pH is a
measure of the activity of the hydrogen ion (H+) in soil solution (Slattery et al. 1999).
Soil pH is defined as the negative log 10 of the hydrogen-ion activity (pH = - log (H+)
3
of soil solution (Evans 1991; Tan 1998). Soils can be separated into a several acidity
and alkalinity categories (Slattery et al. 1999), as shown in Figure 2.1.
NEUTRALITY
3
Slight
Moderate Very strong
Very strong
Strong
Very strong
Moderate
Slight
Very strong
Strong
4 5 6 7 8 9 10
Range in pH common for humid region mineral soils
Range in pH common for most mineral soils
Range in pH common for arid region mineral soils
Extreme pH for acid peat soils
11
ACIDITY ALKALINITY
Attained only by alkali mineral soils
Figure 2.1. Soil pH ranges (Slattery et al. 1999)
2.2 Effect of soil acidity on plants
Soil acidity affects plant growth partially through direct effects of pH on root function
and partly through its effects on soil properties (Russell 1988). Extreme subsoil
acidity may be harmful for plant growth because it can cause shallow rooting, drought
susceptibility, and poor use of nutrients in subsoil (Kauffman 1977). The cause of
poor plant growth on acid soils may vary with soil pH, types and amounts of clay
minerals, contents and types of organic matter, salts levels, and plant species or
genotype (Clark 1982).
In acid soils and mine spoils, the most important factor limiting plant growth is
aluminium toxicity (Foy 1984; Samac and Tesfaye 2003). The problem mainly occurs
below pH 5.0, but it may arise at values as high as pH 5.5 in kaolinite dominant soils.
The poor root development, which occurs in acid soils at pH 5.0 and below, is
probably due mostly to aluminium toxicity that limits both rooting depth and degree
4
of root branching (Foy 1984). Aluminium in solution in acid soils occurs inter alia as
Al3+, Al(OH2)2+, Al(OH)2+, and Al(H2O)3+ (Kinraide 1991). For most plants,
aluminium ions rapidly reduce root growth at micromolar concentrations. The most
toxic ion for the wheat plant is Al3+, while in dicotils the more toxic ions appear to be
Al(OH)2+ and Al(OH)2+ (Samac and Tesfaye 2003).
2.3 Acid Soils in Australia
Like many regions of the world, Australia faces a serious problem with soil
acidification. Acid soil has caused major land degradation and has decreased plant
production over several million hectares of agricultural land in Australia (Evans,
1991). Approximately 35 million hectares of agriculturally productive land presently
have strongly acid soils (pHCa < 4.8) and 55 million hectares are fairly or slightly acid
(pHCa 4.8-6.0) (AACM 1995). Coventry (1985) estimated that Western Australia has
1.0 million hectares of severely acid soil in the eastern wheat belt, with a further 0.5-
0.75 million hectares in the high rainfall southern region.
Maps derived from commercial farm top soil testing data over the past decade (Figure
2.2) show considerable spatial variation in surface soil pH within Australia's
agricultural land and there are major areas of acidic soils (pH CaCl2 less than or equal
to 5.5) in all States (Table 2.1) (The Australian Agriculture Assessment Report 2001).
According to The Australian Agriculture Assessment Report (2001), the largest areas
of strongly acidic soils (pH 4.3 - 4.8) exist in New South Wales (5 to 7 million
hectares), Victoria (4 to 5 million hectares) and Western Australia (1 to 7 million
hectares). The largest areas of moderately acidic soils (pH 4.8 - 5.5) are in Western
Australia (7 to 19 million hectares) and New South Wales (11 to 13 million hectares)
and to a lesser extent Victoria (2 to 3 million hectares). These estimations do not
include all of the area where severe subsoil acidity occurs beneath a less acid topsoil.
5
Table 2.1 National and State areas of surface soil (0 - 10 cm) in several pH (measured
in calcium chloride solution) bands based on information from the
Australian Soil Resources Information System (first number) and
commercial laboratories (second number) (The Australian Agriculture
Assessment Report 2001).
< 4.3 4.3 - 4.8a a 4.8 - 5.5a 5.5 - 7.0a 7.0 - 8.5a > 8.5 Totalc
(million hectares)
New South Wales 0.2 - 1.1 4.8 - 7.1 12.7 - 10.6 18.5 - 10.9 1.5 - 7.9 0 - 0.0b 37.6 - 37.8
Queensland ~ 0.3 0.6 - 1.0 1.5 - 1.8 7.4 - 3.7 0.8 - 4.3 0 10.5 - 11.1
South Australia <= 0.1 0.2 - 0.5 0.8 - 1.4 4.3 - 3.6 6.7 0.0b 11.9 - 12.2
Tasmania ~ 0.1 0.6 - 0.5 1.0 - 0.9 0.0b - 0.3 0.0b 0 1.6 - 1.8
Victoria 0.4 - 1.0 4.1 - 4.5 2.0 - 3.1 4.8 - 2.0 2.9 - 3.5 0 - 0.0b 14.1 - 14.2
Western Australia 0.1 - 0.7 1.0 - 7.5 7.4 - 18.9 1.4 - 2.4 0.0b - 1.1 0 21.4 - 19.2
Australiac 1.1 - 3.3 11.3 - 21.2 36.8 - 25.2 36.3 - 22.9 11.8 - 23.5 0.0b - 0.1 97.3 - 96.2 aInclusive b Numbers rounded to 0.0 range from 0.01 - 0.03. c Total values may be slightly different to those obtained by adding up the values in the table because of rounding errors.
Figure 2.2. Interpolated topsoil pH (1990-1999) (The Australian Agriculture Assessment Report 2001).
6
Many Western Australian agricultural soils require lime applications to overcome soil
acidity, which is widespread and which can affect both topsoils and subsoils (Penny
2002). Two thirds of 10 million hectares of the Western Australian wheatbelt are
affected by soil acidity (Leonard and Boland 1995). It is estimated that potential
agricultural production worth $70 million is lost annually in Western Australia
because of acid soil (Leonard and Boland 1995). Miller (2002) reported that 575,980
tonnes of lime were used on agricultural land of Western Australia in 1999/2000 and
in more recent years the amount is about 1M tonnes/year.
2.4 Liming Resources and Lime Requirement
Liming is one of the most common ways to ameliorate acid soils. Barber (1984)
defined liming material as a material, which contains calcium and/or magnesium,
which reduce the effects of soil acidity. Liming reduces the toxicity of aluminium
(Ritchie 1989), the concentration of hydrogen ions and also adds base-forming cations
to the soil (Thompson 2004). The solubility and plant availability of most of the
nutrient ions in soil is affected by liming (Seatz and Peterson 1969). Furthermore,
liming can improve soil structure, increase soil biological activity, and enhance the
distribution of roots in soil.
The mechanisms of CaCO3 reaction with acid soils are complex (Bear 1969). CaCO3
dissolves and hydrolyses to form OH- ions, the reaction is as follows:
CaCO3 + H2O Ca2+ + HCO3- +OH- (Seatz and Peterson 1969; Thomas and
Hargrove 1984).
In general, the reaction of lime and acid soils (Seatz and Peterson 1969) may be
written as:
2Al-soil + 3 CaCO3 + 3H2O 3Ca-soil + 2Al (OH)3 + 3 CO2 and
2H-soil + CaCO3 Ca-soil + H2O + CO2
Liming resources are valued for their capacity to ameliorate soil acidity and to
maintain the availability of calcium and magnesium for crops. There are a number of
liming materials and each liming material has a specific composition and capacity to
neutralize acidity. The quality of the materials depends on their mineralogy, purity,
and on the size of the particles (Heckman 2000).
7
The standard for measuring purity is calcium carbonate equivalence (CCE) (Spies and
Harms, 2004) so that the CCE value for pure calcium carbonate is 100 % (Whitney
and Lamond 1993). The CCE values of some liming materials are shown in Table 2.2.
Table 2.2. Calcium carbonate equivalence values of some liming materials (aHeckman
2000; bThompson 2004).
Liming Material a, b Source b Chemical Formula a, b
CCE (%) a
Calcium silicate Calcium carbonate Calcium magnesium carbonate Calcium hydroxide Calcium oxide
Slags Limestone Dolomite Slaked lime Burned lime, quicklime
CaSiO3 (and other) CaCO3CaCO3.MgCO3Ca(OH)2CaO
60-90 100 109 136 179
The fineness of liming materials is important because the surface area usually affects
dissolution rate (Whitney and Lamond 1993). Small particles dissolve quickly and so
decrease soil acidity quickly, whereas coarse particles may react very slowly and are
of reduced value in managing soil acidity (Spies and Harms 2004).
Seatz and Peterson (1969) defined the lime requirement of soils as the amount of
liming material that should be supplied to increase the pH level of soil (depth not
specified) to the desired value for a particular land use. Liming materials are applied
commonly to raise soil pH to the desirable values for growth of particular plants
(Cregan et al. 1989). There are several factors that need to be considered for
determining the lime requirement of a soil, where both topsoil and subsoil need to be
ameliorated. Under these circumstances the determination of lime requirement and the
application of lime become complex (Adams, 1984). Thompson (2004) defines soil
pH buffer capacity as the resistance capacity of the soil to change in pH. The pH
buffering capacity is influenced by properties of soil components, including clay
content and clay type, organic matter and hydrous oxides of Fe, Al or Mn, these are
constituents that are capable of reacting with H+, Al3+ and OH-, and are the effective
pH buffers in soil (Gilkes et al. 2003; Slattery et al. 1999).
In agricultural practice, lime is mostly applied through surface application and may be
mixed with soil by cultivation (Cregan et al. 1989). According to Barber (1984) lime
is usually broadcast on the soil surface at rates of 2 to 12 t ha-1. Liming has also been
8
placed as a band near the seed of legume crops where it is described to provide
optimum condition for both root and rhizobia which can be particularly sensitive to
soil acidity (Barber 1984).
2.5 Industrial Byproducts as Liming Agents
The quantity of industrial byproducts is increasing as global mining, manufacturing
and energy production increase. Industrial byproducts are recycled, placed in landfills,
incinerated, dumped in the sea, used as building material or used on farmland (Tan
1994). According to Barker et al. (2000) a major concern over environmental and
agricultural uses of industrial by-products on land is that some contain chemical
constituents that might have hazardous effects on land, water and biota. Therefore, in
most developed countries stringent environmental regulations specify the conditions
under which industrial byproducts can be applied to soils.
The beneficial use of industrial byproducts in agriculture may be to ameliorate land,
reduce degradation of the environment, contribute to the preservation of resources and
provide effective favourable solutions for the disposal of industrial byproducts
(Francis and Youssef 2004). Much research has shown that byproducts from industrial
processes have valuable uses in agriculture for example some byproducts may add
nutrients and organic matter to soil and help recover soil structure (Barker et al.
2000). Byproducts from some industrial processes using limestone or producing lime
like byproducts can be used for neutralizing soil acidity (Cregan et al. 1989). Apart
from organic byproducts, the most common industrial byproducts which are applied
to agricultural land are coal combustion residues, gypsum containing by-products
from chemical processes, residues from the mining and beneficiation of ores, wood
ashes and various slags (Sims and Pierzynski 2000). This thesis investigated the
nature and use of slag, wood ash and chicken litter ash, which are presently or will be
readily available resources in southern Western Australia.
2.5.1 Slag
2.5.1.1 The nature of industrial slags
Slags are non-metallic by-products of steel and other smelting industries (Kalyoncu
1998; Bolan 2004). Some are a result of lime being added to furnaces in order to
9
separate silicon and phosphate impurities from metals. Slags are commonly composed
primarily of CaSiO3 and similar compounds (Miller et al. 2000). Slags are used in
building and road construction, cement manufacture, concrete aggregate, agricultural
fill and glass manufacture, as mineral supplements to stock, and also as liming agents
in agriculture (Kalyoncu 1998; Lee 1974). In the early 20th century, slags produced by
iron and steel-making industries were commonly used in agriculture as liming agents
in Europe and North America (Miller et al. 2000). More recently, slags have been
used as plant nutrient sources and soil amendments because most slags have high Ca
and Mg contents, and in some instances contain significant amount of P and various
micronutrients (Bolan 2004).
Three forms of slag are commonly used as agricultural amendments (Barber 1984): (i)
blast furnace slag, that is usually used as a liming agent for acid soils and which also
provides Ca and Mg for plant nutrition and soil structure benefits; (ii) open-hearth
slag, which is also rich in Ca and Mg, and can contain high amounts of Mn, this also
has a good liming effect; (iii) basic slag, which has mostly been used as a P source
rather than a liming agent although it does provide a liming benefit. Blast furnace
slags consist mostly of silicates and alumino-silicates of lime (Lee, 1974) and contain
smaller amounts of other alkali elements (Barber 1984; Francis and Youssef 2004).
The chemical constituents of typical blast furnace slags (by mass) are shown in Table
2.3. (Lee 1974). Open-hearth slag is from furnaces where pig iron is made into steel.
This type of slag may be applied to soil as a source of Fe and Mn, because it contains
approximately 200 g Fe and 100 g of Mn kg-1 (Barber 1984). Basic slag is a by-
product of the refining of pig iron to steel where phosphatic iron ores have been used
and the P in this type of slag may be readily accessible to plants growing on acid soils
(Barber 1984).
Table 2.3. Chemical constituents of blast furnace slag (Lee 1974).
Constituent Chemical Formula Percentage Lime Silica Alumina Magnesia Total sulphur Total iron
CaO SiO2Al2O3MgO S FeO, Fe2O3
36 – 43 % 28 – 36 % 12 – 22 % 4 – 11 % 1 – 2 % 0.3 – 1.7 %
10
A review of Australia and New Zealand slags was conducted by Li and Gilkes (2002).
They summarised the typical major element chemical compositions of those slags
including British Standards Institute reference slags (Table 2.4). Two slag products
have been applied to New Zealand soils, European slag, and Glenbrook slag (Bolan
2004). The chemical characteristics of the two slag materials from New Zealand are
summarised in Table 2.5.
Table 2.4. Major element composition of slags (Li and Gilkes 2002)
Slags Al2O3
(%)
CaO
(%)
Fe2O3+
(%)
K2O
(%)
MgO
(%)
MnO
(%)
P2O5
(%)
SiO2
(%)
SO3
(%)
TiO2
(%)
HIsmelt 15.09 36.60 3.70 nd 8.72 0.57 0.62 27.37 0.27 0.75
Whyalla 17.15 34.85 0.81 0.21 9.89 0.33 nd 29.76 1.18 0.76
NZ slag 19.68 15.07 1.87 0.07 13.47 0.94 nd 8.44 0.34 36.08
BCS-367
measured
20.65 30.15 0.82 1.07 6.72 1.01 0.095 31.47 2.23 0.81
BCS-367
expected
20.00 32.40 1.00 1.17 7.10 1.16 na 34.40 2.34 0.75
+ All Fe expressed as Fe2O3
Table 2.5. Chemical compositions of slag products used in New Zealand (Bolan 2004)
Type of slag European slag Glenbrook slag Source Steel factory Steel factory Common name Belgian slag Kobmax Lime content* (%)
44.9 52.2
pH 9.7 12.6 Phosphorus (%) 3.9 0.7 Sulphur (%) - 0.2 Calcium (%) 32.2 37 Magnesium (%) 3.2 5.3 Boron (%) - 0.10 Fluoride (%) 0.8 -
* Lime is presented as burnt lime (CaO) in European slag and Glenbrook slag .
Li and Gilkes (2002) have conducted research on slag from the HIsmelt Iron
Company in Western Australia. The typical mineralogical composition of HIsmelt
slags has been described by Li and Gilkes (2002) as follows: merwinite
(MgO.3CaO.2SiO2); gehlenite (2CaO.SiO2.Al2O3); akermanite (2CaO.MgO.2SiO2)
11
Mg, Al-spinel (eg. Mg, Al2O4); magnesia-wustite (Fe2+Mg) O); and an unknown iron-
sulphur phase. Li and Gilkes (2002) summarised the detailed mineralogical
composition of three slags in Table 2.6.
Table 2.6. Mineralogical compositions of slags (Li and Gilkes 2002)
Type of slag Mineralogical composition HIsmelt slag Akermanite (2CaO.MgO.2SiO2)
Gehlenite (2CaO.Al2O3.SiO2) Merwenite (3CaO.MgO.2SiO2) Monticellite (CaO.MgO.SiO2) Spinel (Mg Al2O4) Metallic Fe (little)
Whyalla slag Akermanite (2CaO.MgO.2SiO2) Gehlenite (2CaO.Al2O3.SiO2) Monticellite (CaO.MgO.SiO2) Spinel (Mg Al2O4) Metallic Fe (little)
New Zealand slag Perovskite (CaO.TiO2) MgTi2O5 CaMg(SiO3)2 Spinel (Mg Al2O4) Anatase Metallic Fe (little)
2.5.1.2 Application of slags in agriculture
Slags can be used as fertilizers and have been commonly used as sources of
phosphorus, Ca, Mg and other nutrients (Bolan 2004). Slag fertilizers have been
widely adopted in Europe, America, New Zealand, Egypt, and several other countries
(Lee 1974; Kalyoncu 1998).
Slags have been used on paddy soils in Japan as a source of silicon in order to
increase rice production (Kato and Owa 1997a). The application of slags also
increases pH and the calcium concentration in soil solution (Kato et al. 1997). The
application of calcium silicate slags to rice increased yields by about 30% in each of 3
years after application (Snyder et al. 1986). Calcium silicate slags, have also
increased sugarcane yields in the USA as well as the silicon concentration in plant
tissue (Anderson et al. 1991; Alvarez et al. 1988). Slags also provide a substrate for
the growth of bacteria in soil including Thiobacillus ferrooxidans, Thiobacillus
thiooxidants, and Thiobacillus thioparus (Male et al. 1997).
12
Slags are used on agricultural soils as liming agents. Lintz-Donawit slag has been
used as liming agent for pastureland in northern Spain (Rodriguez et al. 1994). Slag
appeared to be a useful liming material, increased both yield and the concentrations of
phosphorus, calcium, and magnesium in plants (Rodriguez et al. 1994). Khan et al.
(1994) studied the application of basic slags from iron making industries to acid
sulphate paddy soils. They determined that basic slags improved yield of rice, and
increased uptake of calcium, magnesium and phosphorus.
2.5.2 Wood Ash
2.5.2.1 The Nature of Industrial Wood Ash
Wood ash is a by-product from the forest and other industries, which produce wood
fired-boiler ash and ash from combustion of waste wood, twigs and leaves (Nkana et
al. 2002; Vance and Mitchell 2000). Several studies have shown that wood ash can be
used as a liming agent and also as a nutrient source. The neutralizing value of wood
ash is usually expressed as its calcium carbonate equivalent (CCE), which may range
from 10-90 %. According to Nkana et al. (2002) the application of wood ash as a
liming agent can increase soil pH, Ca, Mg, inorganic C, and SO4. Wood ash might
also increase the availability of some soil nutrients to plants because of exchange
with SO4 and OH ions (Nkana et al. 2002).
Most of the inorganic nutrients including minor elements in wood are retained in the
ash during combustion process with most N and some S being lost (Perkiomaki 2004).
The composition of wood ash depends on boiler combustion efficiency and the tree
species used (Clapham and Zibilske 1992; Vance and Mitchell 2000). The content of
C in wood ash varies with combustion efficiency, with some C remaining as unburnt
wood, charcoal and carbonate salts (Vance and Mitchell 2000). Demeyer et al. (2001)
summarise the findings of several researchers concluding that the properties of wood
ash depend on many factors: type of plant, part of plant combusted (bark, wood,
leaves), type of waste (wood, pulp or paper residue), combination with other fuel
sources, and conditions of combustion, collection and storage.
Lerner and Utzinger (1986) reported that the calcium oxide (i.e. Ca expressed as CaO)
content of wood ash ranges from 30% to 60% of the ash and various Ca compounds
13
14
may be present including CaO, Ca(OH)2, CaCO3 and CaSO4. Wood ash contains most
of the essential plant nutrient elements (Nkana et al. 2002) (Table 2.7). The chemical
composition of wood ash from different plant species was determined by Lerner and
Utzinger (1986) and is summarised in Table 2.8.
Table 2.7. Concentrations of total and water-soluble plant nutrients in wood ash
(Nkana et al. 2002)
Parameter Concentration
pH-H2O (1:5)
CCE (%)
10.2
27.3
Total content
Ca
Mg
K
Na
P
Fe
Mn
Zn
Cu
7.8 %
0.8 %
1.7 %
416 ppm
1360 ppm
6066 ppm
1253 ppm
267 ppm
52 ppm
Water extractable
Ca
Mg
K
Na
Cl-
NO3-
163 ppm
984 ppm
0.68 %
57 ppm
148 ppm
58 ppm
Element composition
P K Ca Mg Mn Fe B Cu Zn Al Na Pb Cr Ni Cd
Species
% % % % ppm ppm ppm ppm ppm ppm ppm ppm ppm ppm ppm
Black Cherry *
Hackberry *
Red Oak *
White oak *
Mixture *
Salix #
Forest residue #
Mischantus #
Reed Canary Grass #
Eucalyptus #
Arundo Donax #
Lucerne #
1.0
0.8
0.8
0.8
1.0
2.0
2.5
2.3
0.5
0.8
1.7
1.7
5.7
5.1
12.9
5.1
4.4
6.3
9.9
2.2
1.3
4.4
8.5
11.8
27.1
27.3
24.2
27.1
20.3
27.5
20.4
9.1
3.9
45.5
5.5
19.8
1.5
1.3
2.0
1.3
1.6
2.2
4.0
6.5
0.6
3.5
6.1
1.8
669
742
615
680
595
n.a
n.a
n.a
n.a
n.a
n.a
n.a
1302
989
817
1179
1535
1328
1328
4266
898
3287
2514
1049
271
254
244
260
248
n.a
n.a
n.a
n.a
n.a
n.a
n.a
57
54
57
62
108
n.a
n.a
n.a
n.a
n.a
n.a
n.a
82
66
68
87
853
n.a
n.a
n.a
n.a
n.a
n.a
n.a
2932
2121
1150
2826
3561
1667
1799
6430
1129
714
2196
793
1125
637
340
978
1422
3078
3412
4673
148
12611
6216
2596
24
26
27
19
673
n.a
n.a
n.a
n.a
n.a
n.a
n.a
8
9
5
7
12
n.a
n.a
n.a
n.a
n.a
n.a
n.a
12
14
6
18
11
n.a
n.a
n.a
n.a
n.a
n.a
n.a
2
1
1
1
3
n.a
n.a
n.a
n.a
n.a
n.a
n.a
Average 1.3 6.5 21 2.7 660 1707 255 67 231 2276 3103 153 8.2 12.2 1.6
Table 2. 8. The chemical composition of ash derived from diverse plant species (n.a. not analysed) (*Lerner and Utzinger 1986; #Onderwater et
al. 2001).
15
2.5.2.2 Application of wood ash in agriculture
The application of wood ash to agricultural land increases soil pH and may increase
productivity (Etiegni et al. 1991). According to Rumf et al. (2001) the addition of
wood ash increased pH and base saturation, improved biotic conditions of soils, and
did not have any detrimental effects in the short term.
Clapham and Zibilske (1992) have conducted glasshouse and laboratory experiments
in order to determine the effectiveness of wood ash as a liming agent and found that
soil EC, K, Ca, extractable soil P, Fe, Zn, Cu, and Mn increased linearly with
increasing application rate of wood ash (0 to 20.17 g/kg soil). Mbahrekire et al.
(2003) measured the nutrient element composition of bean (Phaseolus vulgaris) and
soybean (Glycine max L.) grown on soils with wood ash amendment. They
demonstrated that the application of wood ash to the soil at rates of up to 40 ton/ha
increased the plant height by a factor of 1.5 for beans and 1.2 for soybeans with
associated increases in biomass of 1.7 and 1.9 respectively. The increases in plant
height and biomass are attributed mainly to the presence of P, K, Ca and Mg in wood
ash.
2.5.3 Chicken Litter Ash
2.5.3.1 The Nature of Industrial Chicken Litter ash
Chicken litter is a mixture of chicken manure, plant materials including wood
shavings and sometimes mineral particles. For a number of physical and chemical
properties (e. g. heating value, moisture content) it is comparable to wood chips
(Power Plant Research Program 1998). Chicken litter provides a rich source of plant
nutrients and is commonly used in agriculture (Pote et al. 2003). Chicken litter is
commonly applied directly to agricultural land as a fertilizer, however, this has
resulted in excessive levels of phosphorous and nitrogen leachate in some places and
it may contribute to the appearance of flies and toxic micro- organisms (Power Plant
Research Program 1998).
16
One method to overcome these problems is by burning the chicken litter as a fuel
source for power production (Power Plant Research Program 1998). Although all N
and most S are lost during combustion, the ash resulting from the burning process has
value as a multi-element fertilizer and is now recognised as a valuable source of plant
nutrients. Codling et al. (2002) summarised the characteristics of chicken litter ash as
a potential source of plant nutrients (Table 2.9).
Table 2.9. Chemical properties of chicken litter ash (Codling et al. 2002)
Analyte Chicken litter ashpH (1:2 H20) 12.2 EC (1:2 H20), mS/cm 27.5 Water soluble phosphorus, mg/kg <0.1 Mehlich-3-extractable phosphorus g/kg 43 Total P, g/kg 53 Total Ca, g/kg 9 Total Mg, g/kg 1.8 Total K, g/kg 3.9 Total Cd, mg/kg 0.4 Total Ni, mg/kg 14.8 Total As, mg/kg 15 Total Pb, mg/kg 6 Total Cu, mg/kg 43.1 Total Fe, g/kg 4.3 Total Mn, g/kg 1.6 Total Zn, g/kg 0.6
John Hatcher, a company in the UK has developed a fertilizer named Fibrophos
(Fibrophos 2006). It is derived from the incineration of deep chicken litter at a
temperature in excess of 800oC, as a fuel for state of the art power stations. John
Hatcher provides the ash as a compound fertilizer containing most of the elements
required for plant growth (Table 2.10).
17
Table 2.10. Nutrients present in Fibrophos (a chicken litter ash) based on the grades in
Southern and Central England/Wales (Fibrophos 2006).
Analyte Concentration P (P2O5), % 22 K (K2O), % 12 Ca (CaO), % 25 S (SO3), % 7 Mg (MgO), % 5 Na (Na2O) 3 Fe, mg/kg 4000 Mn, mg/kg 2500 Zn, mg/kg 2000 Cu, mg/kg 500 B, mg/kg 150 Mo, mg/kg 30 Co, mg/kg 10 I, mg/kg 5 Se, mg/kg 5 Neutralising value, % 15
2.5.3.2 The use of Chicken Litter Ash in Agriculture
The application of chicken litter ash to agricultural land has not been widely adopted
and no research has been carried out in Australia. Codling et al. (2002) in USA have
conducted research into the effectiveness of poultry litter ash as a source of
phosphorus to agricultural crops. They grew wheat in an acidic soil and compared the
effectiveness of the ash as a P fertilizer with potassium phosphate. They found that
the two source of phosphorus were not significantly different. The metal
concentrations in wheat fertilised with poultry litter ash were lower, possibly due to
the liming effect of the ash reducing the availability of metals. They concluded that
poultry litter ash is an effective source of phosphorus.
The John Hatcher Company in the UK has carried out plant growth experiments over
the past 8 years to evaluate Fibrophos in relation to the yield and quality of various
crops. They have included Triple Superphosphate (TSP) and Muriate of Potash
(MOP) as standards (Fibrophos 2006). The results presented in sales literature show
that the phosphate and potash in Fibrophos are as effective as Triple Superphosphate
18
and Muriate of Potash and that Fibrophos also provides other major and minor
nutrients. These data have not been published in peer-reviewed journals so await
critical scrutiny. However the results are consistent with those published by Codling
et al. (2002).
19
Chapter 3
3.0 A Laboratory Evaluation of the Industrial Byproducts: Chicken Litter Ash,
Wood Ash and Iron Smelting Slag for use as a Combined Liming Agent and
Phosphorus Fertilizer
3.1 Introduction
Soil acidity is a major problem worldwide as it decreases plant growth by affecting
the availability of nutrients and causes various toxicities. Acid soils are commonly
deficient in phosphate (P) so that both conditions require correction, which can be
carried out by the application of a single mineral ameliorant with appropriate
properties. Some alkaline industrial byproducts may be suitable as they contain P,
which may be available to plants. These materials include iron smelting slag, wood
ash and chicken litter ash but their fertilizer effectiveness is poorly defined.
Byproducts are commonly dumped in landfill so that the use of byproducts to
ameliorate land will contribute to the preservation of alternate resources and provide
an effective solution for the disposal of byproducts (Francis and Youssef 2004).
A laboratory assessment of the potential agronomic effectiveness of a material to be
used as a P fertilizer has to be made to determine appropriate rates of application in
the field. In order for a material to be an effective P fertilizer, substantial amounts of P
should dissolve shortly after application to soils and all P should eventually dissolve
(Hughes and Gilkes 1984). Conventional chemical P fertilizers (SP, DAP, MAP) are
mostly soluble in water and are highly effective. Rock phosphate is almost insoluble
in water as it relies on soil acidity and rhizosphere acidity to promote dissolution and
is consequently much less effective than chemical fertilizers (Khasawneh and Doll
1978). The solubility of the above-mentioned byproducts in soil is not known.
The effectiveness of poorly soluble phosphate fertilizers such as rock phosphate and
phosphatic byproducts may be assessed by standard analytical procedures (AOAC
1975) that determine the solubility of phosphate in water, citric acid, neutral
ammonium citrate and alkaline ammonium citrate. Depending on the composition of
the fertilizer and its reactions in soil, a particular extractant may provide the best
prediction of fertilizer performance as determined by field or glasshouse experiments
20
and appropriate calibration is required (Colwell 1963). This chapter investigates the
nature of byproducts (chicken litter ash, wood ash, iron-smelting slag) that may act as
a combined liming agent and phosphate fertilizer and evaluates them using standard
AOAC fertilizer analyses.
Table 3.1. The nomenclature for calcined chicken litter samples produced by
calcination at various temperatures and their pH measured in water
Key Explanation pH H2O
(1:5)
C500 Chicken litter burnt at 500oC 10.18
C550 Chicken litter burnt at 550oC 10.27
C600 Chicken litter burnt at 600oC 10.29
C650 Chicken litter burnt at 650oC 10.33
C700 Chicken litter burnt at 700oC 10.37
C750 Chicken litter burnt at 750oC 10.38
C800 Chicken litter burnt at 800oC 10.52
C850 Chicken litter burnt at 850oC 10.55
C900 Chicken litter burnt at 900oC 10.56
C950 Chicken litter burnt at 950oC 10.59
C1000 Chicken litter burnt at 1000oC 10.62
CLA Chicken litter partly burnt in incinerator at 700oC to 800oC 9.93
CLAT CLA heated in furnace at 700oC 11.31
RP Sechura rock phosphate 7.96
WA Wood ash 12.77
Slag Iron smelting slag 10.59
3.2 Materials and Methods
3.2.1. Calcination of chicken litter
A bulk sample of chicken litter was supplied by Blair Fox Generation, which is
developing a power station to be fired by this material. Combustion temperatures and
conditions may vary substantially during this process, so that diverse combustion
products may be produced. Subsamples of 1 kg of the chicken litter were burnt in a
21
ventilated electric muffle furnace for 1 hour at 500o, 550o, 600o, 650o, 700o, 750o,
800o, 850o, 900o, 950o, and 1000oC respectively. Large amounts (>100kg) of chicken
litter were partially and totally burnt in a commercial incinerator. Chicken litter was
partially burnt (CLA) for 36 hours at temperatures that varied between 700oC to
800oC. Combustion was only partial as much carbonised litter (charcoal) remained.
Totally burnt chicken litter (CLAT) was derived from CLA, by heating overnight in a
fully oxidising environment at 700oC to remove residual charcoal from CLA. A key to
the materials investigated, abbreviations used to identify these materials and the pH of
these materials including Sechura rock phosphate are given in Table 3.1.
3.2.2 Industrial Byproducts
Iron smelting slag came from the HIsmelt Kwinana Demonstration Plant, Western
Australia, which utilises iron ore, lime and coal. Wood ash was from eucalyptus
(Mallee sp.) timber and litter, which is burnt in an experimental bioenergy Power
Station at Narrogin Western Australia. The chemical compositions of the byproducts
and Sechura rock phosphate, which as it acts as a combined P fertilizer and liming
agent (Khasawneh et al. 1980) was included for comparative purposes, are given in
Table 3.3.
3.2.3 Characterisation of the materials
The pH of the materials was determined in a 1:5 deionized water extract. Calcium
carbonate equivalent (CCE) was determined as in the AOAC 1.005 procedure,
(AOAC 1975). Major elements were determined by atomic absorption
spectrophotometry (AAS) (Perkin-Elmer, Analyst 300, Norwalk, CT, USA) and trace
elements with a model PE ELAN 600 inductively coupled plasma – mass
spectrometry (ICPMS) instrument (Perkin-Elmer, Norwalk, CT, USA) after
perchloric acid digestion. Total phosphorous in these digest was determined
colorimetrically using the molybdovanadophosphate (yellow) method (Rayment and
Higginson 1992). The compounds in byproducts were identified by X-ray powder
diffraction (XRD) using a Philips PW3020 diffractometer. Samples for scanning
electron microscopy and energy dispersive X-ray spectrometry (EDS) using a JEOL
3600 instrument were placed on metal stubs and carbon coated.
22
3.2.4 Chemical extraction of the materials (AOAC Method)
Unlike many commercial P fertilizers little of the P in byproducts is soluble in water
(Table 3.2). The byproducts were analysed for available P using Association of
Official Analytical Chemistry (AOAC) standard methods (AOAC 1975) utilising
citric acid (CA), neutral ammonium citrate (NAC) and alkaline ammonium citrate
(AAC) extractions. Gilkes and Palmer (1979) have shown that the standard AOAC
extraction procedures may not be optimum for the best prediction of the agronomic
effectiveness of calcined phosphate minerals. They used various extraction times to
evaluate the kinetic and congruency of dissolution of the phosphates to determine
optimum extraction times. The same procedure has been followed here to determine
an optimum procedure for byproducts and also for Sechura rock phosphate that was
included as a comparison material. Citric acid 2% (CA) was prepared by dissolving
100g of citric acid in five litres of deionised (DI) water. Neutral ammonium citrate
(NAC) prepared as in the standard procedure, AOAC 2.036 (AOAC 1975). Alkaline
ammonium citrate (AAC) solution was prepared by dissolving 865 g citric acid in two
litres of water to which three litres of 5M NH4OH were added (Boxma 1977). The pH
was adjusted to 9.35 and the specific gravity to 1.08 by small additions of these
reagents. The solid: solution ratio for each extractant was 1:100 w/v and the
temperature of extraction for NAC, AAC and CA was 65oC, 65oC and 25oC
respectively.
The extractants were shaken in a temperature controlled mechanical shaker with a
vigorous action that kept particles in suspension. Aliquots of the suspension were
removed for analysis after 7 times (0.5, 1, 2, 6, 24, 72, and 120 hours). Aliquots were
quenched with pure ice (NAC and AAC) and cold water (CA) to slow the reaction
during filtering. The suspension was immediately filtered through 0.22 μm Millipore
filters and the filtrate analysed for phosphorus, calcium, magnesium, sodium and
potassium. The solid residue after 120-h extraction was washed three times with DI
water and then analysed by XRD and SEM.
3.2.5 Chemical analysis of the extracts
Phosphate was determined in the extracts by spectrophotometry (molybdate blue
method) (Rayment and Higginson 1992). The reagents were 0.02 M ammonium
23
molybdate and 0.001 M hydrazine sulphate solution; equal volumes were freshly
mixed for each batch of analyses. A 0.3 ml aliquot of the quenched citrate solution
was added to 1 mL of hydrochloric acid and diluted with DI water to fill a 10 mL
volumetric flask. Next 1 ml of the solution was mixed with 4 ml hydrazine solution
and 5 ml of molybdate solution in a flask. The solution was shaken and placed in a
boiling water bath for 10 minutes then cooled to room temperature in a water bath.
The absorbance was read at 820nm on a Hitachi U-1100 spectrophotometer using a
bandwidth of 2 nm and 1 cm path length cell. Calcium, magnesium, sodium and
potassium were determined by AAS after dilution and addition of appropriate
ionisation suppressants (Gilkes and Palmer 1979).
3.2.6 Glasshouse experiment
Details of a glasshouse experiment with an acid lateritic soil and ryegrass to evaluate
the byproducts have been described in a paper by Yusiharni and Gilkes (2006), which
occur in this thesis as Chapter 4. In this chapter values of agronomic relative
effectiveness (RE) derived from these plant yield data with monocalcium phosphate
(MCP) as the reference fertilizer have been related to the solubility (availability) of P
determined using CA, NAC and AAC extractions following the procedure of Gilkes
and Palmer (1979).
3.3 Results and discussion 3.3.1. Calcination of chicken litter
The calcined chicken litter samples had pH values that ranged from 10.18 (C500) to
10.62 (C1000) (Table 3.1). For the calcined chicken litter ash samples, the solubility
of phosphorus in AOAC citrate extractants varied with period of extraction and the
type of extractant. The percentages of total P extracted from chicken litter ash
calcined at various temperatures and for various extraction times are shown in Figure
3.1. The major trend is that phosphorus solubility in all three extractants increased as
calcination temperature increased up to the maximum calcination temperature of
1000oC.
24
Citric Acid
0
20
40
60
80
100
120
0.5 1 2 6 24 72 120
Duration of Extraction (Hour)
% P
Ext
ract
ed
A
Neutral Ammonium Citrate
01020304050607080
0.5 1 2 6 24 72 120
Duration of Extraction (Hour)
% P
Ext
ract
ed
B
Alkaline Ammonium Citrate
010203040506070
0.5 1 2 6 24 72 120
Duration of Extraction (Hour)
% P
Ext
ract
ed
C500 C550 C600 C650 C700 C750 C800C850 C900 C950 C1000
C
Figure 3.1. Percentages of total P extracted from chicken litter ash produced at
various temperatures for various durations of extraction in citric acid (A), neutral
ammonium citrate (B) and alkaline ammonium citrate (C).
25
Most dissolution in CA occurred within 0.5 hour whereas dissolution continued for
approximately 6 hours in NAC and 72 hours in AAC. For all three extractants
considerable P had not dissolved after 120 hours of extraction and this is likely to be
present in refractory inorganic or organic compounds. Doak et al. (1965) have
demonstrated that the solubility of calcined Christmas Island Fe, Al containing rock
phosphate in the same citrate extractants increased to a maximum solubility of nearly
100% after calcination at temperatures between 500oC and 650oC and decreased for
higher calcination temperatures. The proportion of total P that had dissolved after
120-h was similar for all three extractants but increased in the sequence
CA>NAC>AAC for short periods of extraction. In contrast Gilkes and Palmer (1979)
observed that the dissolution of calcined iron-aluminium phosphate in CA and NAC
was less than in AAC. The solubility of apatitic rock phosphate fertilizers in these
reagents follows the same trend as for litter ash (CA>NAC>AAC) (Lehr 1980).
The percentage dissolution of the major cations in calcined chicken litter in CA, NAC
and AAC after a 1-h extraction is shown in Table 3.2. Dissolution was not congruent
for any extractant or material as indicated by the different percentage dissolution
values for each element. Dissolution of calcium in CA increased from C500 to C950
and decreased at C1000. For NAC and AAC the percentages of calcium dissolved
were less than for CA. Higher proportions of magnesium, potassium and sodium
dissolved compared to calcium in all three extractants. CA, NAC and AAC dissolved
most magnesium for calcination temperatures between 800oC to 1000oC. In contrast,
there were no systematic trends with temperatures for potassium and sodium. These
diverse behaviours for the four cations indicates that they do not coexist in the
byproducts within a single compound.
26
Table 3.2. Percentages of total phosphorus, calcium, magnesium, potassium and
sodium dissolved after 1hour extraction in citrate solutions for chicken litter calcined
at various temperatures and for Sechura rock phosphate (RP), wood ash (WA) and
slag.
Phosphorus (%) Calcium (%) Magnesium (%) Potassium (%) Sodium (%) Samples
CA NACAAC CA NACAAC CA NAC AAC CA NAC AAC CA NAC AAC
C500 37 37 23 21 21 11 47 46 39 47 52 51 28 34 30
C550 39 37 26 21 21 11 48 47 40 47 53 52 29 35 32
C600 43 40 27 23 21 12 50 49 41 50 54 52 31 38 32
C650 44 41 29 23 22 13 53 51 42 54 58 53 34 43 33
C700 54 42 30 24 22 13 54 52 43 58 64 63 38 45 37
C750 48 44 30 25 22 13 55 52 45 62 67 65 40 46 37
C800 53 45 32 28 22 14 67 62 52 68 74 71 48 51 46
C850 64 46 32 33 22 15 78 70 60 75 82 79 54 57 51
C900 71 47 32 88 62 11 82 71 56 68 33 30 66 31 22
C950 71 48 36 92 40 8 23 94 78 90 32 30 90 39 34
C1000 96 53 48 50 23 20 91 99 85 79 83 79 72 74 69
CLA 75 46 34 88 62 58 82 71 56 95 46 43 80 38 26
CLAT 81 49 39 92 40 39 86 72 60 90 32 30 90 39 34
RP 38 2 1 77 16 3 30 10 6 4 4 3 74 47 32
WA 57 78 69 85 85 88 79 75 82 87 55 51 2 78 79
Slag 80 18 40 40 24 22 55 26 18 6 5 5 30 25 18
The XRD patterns of chicken litter ash that had been calcined at various temperatures
are shown in Figure 3.2.A. The major crystalline compounds present are apatite and
quartz.
27
5 10 15 20 2 5 3 0 35 40 4 5
2 θ ( d e g re e s )
Calcined Chicken Lit ter Ash After CA Extract io n
C100 0
C950
C90 0
C850
C80 0
C750
C700
C6 50
C6 00
C550
C500
Q
Citrate p recip itat ion
B
5 10 15 20 25 3 0 3 5 40 45
2 θ (deg rees )
Calcined Chicken Litter AshQ C10 00
C950
A
C900
C850
C800
C750
C700
C500
C550
C600
C650
A
5 10 15 20 25 3 0 3 5 40 45
2 θ ( d e g re e s )
Calcined Chicken Lit ter Ash After NAC Extraction
C1000
C950C90 0
C850C80 0
C750
C700
C6 50
C6 00
C550
C500
Q
A
C
5 10 15 2 0 2 5 30 3 5 4 0 4 5
2 θ ( d e g re e s )
Calcined Chicken Lit ter Ash After AAC Extract io n
C10 0 0
C9 50
C9 0 0
C8 50
C8 0 0
C750
C70 0
C6 50
C6 0 0
C550
C50 0
Q
A
D
Figure 3.2. XRD patterns of chicken litter calcined at various temperatures before (A)
and after extraction for 120 hours in citric acid (B), neutral ammonium citrate (C) and
alkaline ammonium citrate (D). Q = quartz (d = 3.43 Ǻ), A = apatite (d = 2.84 Ǻ), Cu
Kα radiation.
28
Calcined chicken litter ash contains abundant amorphous material (mostly charcoal)
as indicated by broad background scatter centred at 25o 2θ. As calcination temperature
increased the intensity and sharpness of apatite peaks increased which is due to loss of
charcoal, together with the increased abundance, greater structural order and larger
crystal size of the apatite that formed during calcination (Klug and Alexander 1974).
XRD patterns for the residues of calcined chicken litter ash samples after CA
extraction (Figure 3.2.B) show stronger quartz peaks and a stronger amorphous
carbon band than for CLA as these insoluble compounds have been concentrated by
dissolution of apatite. All the apatite had dissolved in CA for each calcination
temperature. Broad reflections due to precipitated citrate compounds are present for
some CA residues and may be a consequence of the high alkalinity of the ash causing
precipitation of calcium citrate salts.
These XRD results may be compared with the dissolution data shown in Figure
3.1.A., which indicate that for the higher calcination temperatures (≥ 850oC) most P
had dissolved in CA after 120 hours of extraction. Much smaller amounts of P had
dissolved for lower calcination temperatures and a similar trend occurred for Ca, Mg,
K and Na (Table 3.2). It is suggested that CA completely dissolved the inorganic
apatite that is the main form of P for high temperature calcines but did not dissolve
organic forms of P associated with charcoal that persist in the lower temperature
calcines. For NAC extraction, a comparison of Figures 3.1.B and 3.2.C shows that
some apatite did not dissolve for the highest temperature (≥ 850oC) calcines, which is
consistent with less P being extracted (maximum 70%) than for CA, the organic P
once again being insoluble. For the AAC extraction (Figures 3.1.C and 3.2. D) even
less apatite and P (maximum 58%) dissolved.
SEM micrographs and EDS spectra of C500 and the residue of C500 after the three
citrate extractions show the diverse particle sizes, shapes and compositions present in
this material (Figure 3.3). Similar observation were made for the other calcined
materials and their residues. Most grains seen in the micrographs consist mostly of
carbon and contain only a little P and cations.
29
C500 C500 after CA extraction
C500 analysed grain C500 analysed grain after CA extraction
C500 after NAC Extraction C500 after AAC Extraction
C500 analysed grain after NAC extraction
C500 analysed grain after AAC extraction
050
100150200250300350400
0 5 10 15
Energy (keV)
P
Si
KCaMg
0
200
400
600
800
1000
1200
0 2 4 6 8 10
Energy (keV)
cps
Na Mg
P
K
Ca
0
100
200
300
400
500
600
0 2 4 6 8 10
Energy (keV)
cps
Mg
P
Ca
0
100
200
300
400
500
0 2 4 6 8 10
Energy (keV)
cps
Mg
P
Ca
Figure 3.3. Scanning electron micrograph (SEM) and spectra of the indicated particles
for 500oC calcined chicken litter (C500) before and after extraction for 120 hours in
citrate solutions. Most particles are charcoal.
30
The P enriched grains in C500 have complex and diverse chemical compositions. The
grain in C500 indicated in Figure 3.3 contains much Ca and P that could be present in
apatite together with minor K, Mg, and Na that may also be present within apatite
(Lindsay et al. 1989) or possibly in separate compounds such as carbonates or oxides
as would be consistent with the dissolution data in Table 3.2 that indicate incongruent
dissolution. After CA extraction of C500 few Ca, and P grains remained as they had
mostly dissolved, but as only 40% of total P had dissolved much of the remaining P
could be present in organic associated form in the charcoal grains. The rare P enriched
grain indicated in Fig. 3.3 for CA residue is probably a mixture of apatite and a
calcium silicate mineral. Figure 3.3 shows that some Ca and P rich apatite grains
remain after NAC and AAC extraction, which is consistent with XRD and chemical
extraction results. For all three types of citrate residue some of the P must be
associated with the charcoal where it is present at the low concentrations (Codling et
al. 2002) that were detected by EDS (less than 1%). The majority of the non-carbon
grains were silicate minerals and represent sand (quartz, feldspar, etc) that had been
incorporated into the litter.
3.3.2 Dissolution of industrial byproducts
The chemical compositions of the byproducts are given in Table 3.3 and indicate that
these materials will provide several plant material elements in addition to P. Indeed at
the rates of application of byproducts used to lime soils (tonnes/hectare) large amount
of Ca, Mg, K and trace elements (Cu, Zn, Mn, etc) would be provided by the ash
materials. Slag will provide much Ca and Mg, little K and some trace elements. The
concentrations of the heavy metals Cd, Ni, As and Pb in the byproducts are
insufficient to generate an environmental hazard at normal application rates for lime
(Alloway and Ayres 1993). All of the byproducts are likely to be effective liming
agents as they have calcium carbonate equivalent (CCE) values ranging from 93-98%
whereas RP had much smaller CCE (48%) (Table 3.3).
31
Table 3.3. Chemical properties of the industrial byproducts and rock phosphate.
Properties CLA CLAT Slag WA RP
pH (1:5 H2O) 9.93 11.31 10.59 12.77 7.66
EC (1:5 H2O) (dS/m) 1.54 1.62 1.43 1.35 1.31
CCE (%) 94 97 93 99 48
Total phosphorus (%) 3.6 4.75 0.26 0.44 15.85
P soluble in water + (%) 6 6 15 13 2
Total calcium (%) 16.62 18.02 27.82 22.23 19.27
Total magnesium (%) 1.48 1.94 6.07 3.75 0.48
Total potassium (%) 2.93 4.11 0.12 3.65 0.78
Total sodium (%) 1.53 1.86 0.22 2.62 0.98
Total Cd (mg/kg) 5.75 6.62 0.27 0.59 47.2
Total Ni (mg/kg) 15.9 19.3 14.9 52.6 26.1
Total As (mg/kg) 20.8 30.4 3.1 2.1 25.5
Total Pb (mg/kg) 7.4 8.5 0.6 15.4 8
Total Cu (mg/kg) 47.9 52.4 18.2 41.3 11
Total Mn (g/kg) 1.8 1.4 11.2 4.2 1.7
Total Zn (g/kg) 7.4 9.5 0.1 0.2 0.1
+ Expressed as a percentage of total phosphorus
The effects of extraction time and extractant type on dissolution of P from byproducts
are illustrated in Figure 3.4. The solubility of the P in RP was small in NAC and
AAC, and higher in CA reflecting the presence of well crystalline apatite. Apatite is
almost insoluble in water so that when apatite RP is applied to soil, any dissolution
that occurs is the result of a chemical reaction between soil acidity and RP, hence the
use of an acidic extractant (CA) (Khasawneh and Doll 1978). Lim and Gilkes (2001)
showed that the equilibrium solubility of various RPs in CA was reached after
different durations of extraction but that it was generally attained within 24 hours,
32
whereas minor additional dissolution of RP after 24 hours occurred in the present
research.
Citric Acid
0
20
40
60
80
100
120
0.5 1 2 6 24 72 120
Duration of Extraction (Hour)
% P
Ext
ract
ed
Neutral Ammonium Citrate
0
20
40
60
80
100
120
0.5 1 2 6 24 72 120
Duration of Extraction (Hour)
% P
Ext
ract
ed
Alkaline Ammonium Citrate
0
20
40
60
80
100
120
0.5 1 2 6 24 72 120
Duration of Extraction (Hour)
% P
Ext
ract
ed
Figure 3.4. Percentage of P extracted from five phosphatic byproducts by three citrate
extractants for various durations of extraction: ◆ CLA, ■ CLAT, ▲ RP, x WA,
Slag
33
CLAT and CLA showed similar and considerable amounts of dissolution in each
extractant with amounts of soluble P being in the sequence CA>NAC>AAC for
shorter extraction times. For all three extractants there was little or no additional
dissolution after about 6 hours of extraction. Much of the P in WA rapidly dissolved
in all three extractants, with little additional dissolution occurring for longer
extraction periods. The P in slag dissolved more slowly in NAC and AAC than in CA
but essentially all P had dissolved after 6 hours. Only a minor proportion of P in RP
had dissolved in NAC and AAC after 120 hours. Much more of the P in RP dissolved
in CA and most dissolution occurred within a short time.
The diffraction patterns of CLA, CLAT, slag, WA and RP before and after the three
extractions for 120 hours are shown in Figure 3.5. As for the laboratory calcined
chicken litter, the major compounds present in CLA and CLAT are apatite and quartz
with calcite being present in CLA. The broad background for CLA is higher
compared to CLAT due to the carbon having been removed from CLAT by prolonged
calcination. The sharp XRD reflections indicate that CLA and CLAT contain well-
ordered apatite of large crystal size. Based on spacing data, the apatite in CLA and
CLAT was carbonate apatite (Lehr 1980). Much apatite remained in CLA and CLAT
after 120-h extraction in all three extractants, which is consistent with the P
dissolution data (Figure 3.4). Oxalate precipitation occurred for CLA and CLAT
extracted by CA.
The minerals present in Sechura RP are carbonate apatite (francolite) and quartz
(Figure 3.5) (Lim and Gilkes, 2001). Much apatite remains in the residues for all three
extractants, which is consistent with the low extent of dissolution of RP in citrate
extractants shown in Figure 3.4. Slag consists of calcium magnesium silicate
(akermanite) and calcium aluminium silicate (gehlenite) (Li and Gilkes 2002). The
residue of slag after CA extraction contains little akermanite and much gehlenite. The
residues after NAC and AAC extraction contain abundant akermanite and gehlenite. It
appears that there is no relationship between the extent of dissolution of these
compounds and the dissolution of P, which was approximately 100% in all three
extractants. We conclude that P is not contained within these silicates but is present in
slag as a discrete, readily soluble compound.
34
5 10 15 2 0 2 5 3 0 3 5 4 0 45
2 θ ( d e g re e s )
Slag
WA
RP
CLAT
CLA
Byprod ucts
Q
A
Q
C
Ak
G
A
A Q
Ca
A
5 10 15 20 2 5 30 3 5 40 4 5
2 θ ( d e g re e s )
Slag
WA
RP
CLAT
CLA
Byp ro ducts After CA Extract io n
Q
A
A
G
A
A A
B
5 10 15 2 0 2 5 30 3 5 40 4 5
2 θ ( d e g re e s )
Slag
WA
RP
CLAT
CLA
Byprod ucts after NAC Extraction
Q
A
A
Ak
G
C
A
A
A
C
5 10 15 20 2 5 3 0 35 4 0 4 5
2 θ ( d e g re e s )
Slag
WA
RP
CLAT
CLA
Byp rod ucts After AAC Extractio n
Q
A
A
Ak
G
C
D
Figure 3.5. XRD patterns of byproducts (A) and their residues after extraction for 120
hours in citric acid (B), neutral ammonium citrate (C) and alkaline ammonium citrate
(D). Q = quartz (d = 3.43 Ǻ), A = apatite (d = 2.84 Ǻ), C = calcite (d = Ǻ), Ak =
akermanite (d = 2.85Ǻ) and G = gehlenite (d = 3.71 Ǻ), Cu Kα radiation.
35
CLA CLA after CA extraction
CLA analysed grain CLA analysed grain after CA extraction
CLA after NAC Extraction CLA after AAC Extraction
CLA analysed grain after NAC extraction
CLA analysed grain after AAC extraction
0
200
400
600
800
1000
1200
0 2 4 6 8 10
Energy (keV)
cps
Mg
P Ca
0
500
1000
1500
2000
2500
0 2 4 6 8 10
Energy (keV)
cps
Si
Mg
Ca
P
0100200300400500600700800900
0 2 4 6 8 10
Energy (keV)
cps
Si
P KCa
Al
0500
10001500200025003000350040004500
0 2 4 6 8 10
Energy (keV)
cps
Na
Mg
P
Ca
Figure 3.6. Scanning electron micrographs (SEM) and spectra of indicated particles
for original CLA and residues after extraction for 120 hours in three citrate solutions.
36
WA consists mostly of calcite, quartz and several salts but apatite was not identified,
although it has been observed in some plant ashes (Harper et al. 1982). Humpreys et
al. (1987) also found that wood ash mainly consisted of calcite however Etiegni and
Champbell (1991) observed that quicklime (CaO) and calcium silicate (Ca2SiO4)
could be present. All of the calcite dissolved in CA but NAC and AAC residues of
WA contain calcite together with minor amounts of unidentified compounds.
0
50
100
150
200
250
300
0 5 10 15
Energy (keV)
Ca
PSi
K
A
S Cl
0200
400600
80010001200
14001600
18002000
0 2 4 6 8 10 12 14
Energy (keV)
Si
Al Ca
K
B
Figure 3.7. X-ray spectrum of a carbon grain in partly burnt chicken litter ash showing
that it contains minor amounts of Si, P, S, Cl, K, and Ca (A) and a silicate grain in
totally burnt chicken litter ash containing much Si, Al, K and Ca (B).
37
CLAT CLAT after CA extraction
CLAT analysed grain CLAT analysed grain after CA extraction
CLAT after NAC Extraction CLAT after AAC Extraction
CLAT analysed grain after NAC extraction
CLAT analysed grain after AAC extraction
0
1000
2000
3000
4000
5000
6000
7000
0 2 4 6 8 10
Energy (keV)
cps
Mg P
Si
K
Ca
0
500
10001500
2000
2500
3000
35004000
4500
5000
0 5 10 15
Energy (keV)
cps
Na
Mg
Si
Cl
K
Ca
0200400600
800100012001400
0 5 10 15
Energy (keV)
cps
Mg
P
Cl
Ca
Si
0100200300400500600700800900
0 2 4 6 8 10
Energy (keV)
cps
Na
AlSi
K
Ca
P
Figure 3.8. Scanning electron micrographs (SEM) and X-ray spectra of indicated
grains for CLAT and residues after extraction for 120 hours in three citrate solutions.
38
The SEM image of CLA shows abundant charcoal particles and an apatite grain
(Figure 3.6), consisting mostly of Ca and P with a little Mg, an element, which can
substitute for Ca in the apatite structure (McClellan and Gremillion 1980). After CA,
NAC and AAC extractions all calcite had been removed from CLA, some apatite
grains persisted and these are often associated with silicate minerals as indicated by
the EDS spectra of grains in Figure 3.6. The silicates include sand grain and
compounds formed from silicon that was present in plant materials that were
combusted. The ash of plant materials commonly contains organic compounds and
particularly carbon resulting from incomplete combustion (Sander and Andren 1997).
Many particles of carbon are present in CLA and although these contain only minor
concentrations of P, Ca and other elements, they contain much of the total content of
these elements in the materials (Figure 3.7.A). The SEM image for the completely
combusted CLAT (Figure 3.8) is quite different from that of CLA as no carbon
particles are present. Much Ca and P is present in compound particles, variously
containing Si, Al, Mg and K. These compound particles persisted in all three
extractant residues (Figure 3.7) so that the P (as apatite) in these particles may have
been partly protected from dissolution by surrounding silicate compounds.
3.3.3 Relationship of relative agronomic effectiveness (RE) of CLA and CLAT with P
availability determined by chemical extraction.
The solubility of P in bypoducts in AOAC extractants differs for the three extractants
and the duration of extraction. Consequently there is uncertainty over which
combination of extractant and extraction time will be most predictive of the
agronomic effectiveness of byproducts. A comparison of these chemical results with
values of agronomic relative effectiveness (RE) obtained in a glasshouse study
(Chapter 4) (Yusiharni and Gilkes 2006) was done to determine the most suitable
extraction procedure for these P fertilizers (Gilkes and Palmer 1979). Relative
effectiveness is expressed as the substitution value of the fertilizer relative to the
standard fertilizer monocalcium phosphate (MCP), which is the major P compound in
superphosphate. All the byproducts together with Sechura RP were included in this
comparison.
39
r = - 0.90
0
5
10
15
20
25
30
0 20 40 60 80 100 120
% P Soluble in CA for 6 Hours
RE
(%)
WA
CLATSlag
CLA
RP
Figure 3.9. The relationship of relative agronomic effectiveness (RE) and the
solubility of P in CA for 6 hours extraction.
The values of relative effectiveness of the byproducts were less than 10% of the
effectivenss of MCP (Yusiharni and Gilkes 2006) (Chapter 4). No measure of
available P (no combination of extractant type and time) was systematically and
positively related to RE values obtained from the plant experiment and in most
instances there was a negative relationship between RE and the P soluble in
extractants. This situation is illustrated by the relationship between agronomic
effectiveness (RE) and the solubility of P in CA for a 6 hour extraction (Figure 3.9).
The lack of a systematic positive relationship may be a consequence of the high pH of
WA, CLA and CLAT raising soil pH, so that the dissolution of these P sources in soil
and the consequent availability of P to plants is reduced and is not simply related to
the solubility of P in citrate reagents. Where soil pH becomes elevated due to high
rates of application of these alkaline materials as liming agents, apatite in the
fertilizers will not dissolve to the same extent as in an acid soil (Anderson et al.
1985). Furthermore the high concentration of Ca in soil solution due to the dissolution
of Ca compounds in the byproducts will also reduce dissolution of apatite in the soil
due to the common ion effect (Lindsay et al. 1989). Another consideration is that the
high alkalinity of the byproducts (especially CLA, CLAT, WA) may have adversely
affected the capacity of the citrate extractants to dissolve P and or retain dissolved P
40
in solution. Due to these circumstances, CA, NAC and AAC extractions are unable to
predict the agronomic effectiveness of this type of fertilizer.
3.4 Conclusion
This research has shown that the combustion of chicken litter such as occurs in a
thermal power station produces a multi-element fertilizer where much of the
phosphorus is soluble in citrate extractants. In general phosphorus solubility followed
the sequence CA>NAC>AAC for short periods of extraction. Much of the P in CLA
and CLAT was present as the mineral apatite, with the abundance, crystal order and
crystal size of the apatite increasing with calcination temperature. The P in WA and
slag is mostly soluble in citrate extractants whereas much of the P in rock phosphate
is not.
The high value of the correlation coefficient for the relationship between RE and CA
soluble P (0.90) (Figure 3.9) might encourage the view that P soluble in citrate
solution is highly predictive of RE but the relationship is negative and the data points
are not sufficiently dispersed for the regression line to be reliable. This or similar
situations exist for all extractants and extraction times. Thus it is not possible to
predict the relative agronomic effectiveness (RE) of these materials using citrate
extractants, which may be a consequence of the high pH of these materials. Chicken
litter ash, wood ash and slag have important liming values and their application to
acid soils at normal rates for liming will not increase soil pH to levels that prevent the
apatite from eventually dissolving and providing substantial P to plants.
41
Chapter 4
4.0 Plant response to the byproducts: Chicken Litter Ash, Iron Smelting Slag
and Wood Ash as Phosphorus Fertilizers
4.1 Introduction
The industrial byproducts iron smelting slag, wood ash and chicken litter ash contain
phosphate (P) so that both acidity and P deficiency can be overcome by a single
application of byproduct, however the agronomic effectiveness of the P in these
materials is not known. Previous studies have used chemical tests to evaluate the
byproducts as phosphorous fertilizers and demonstrated that they might be a
significant asset to agriculture, however direct analysis of agronomic values of the
byproducts needs to be undertaken using plant growth experiments. This chapter
reports on an experiment where iron-smelting slag, wood ash and chicken litter ash
were applied to an acid soil to evaluate their capacity to supply P to plants relative to
a standard fertilizer.
4.2 Materials and methods
4.2.1 Soil
The <2mm fraction of the topsoil (0-10 cm) of a Balkuling lateritic soil (McArthur
1991) from Bakers Hill, 73 km east of Perth, Western Australia was used in this
research and is the same soil that was used by Palmer and Gilkes (1982) in their
glasshouse evaluation of P fertilizers. Soil properties are as follow; pH (1:5 H2O) 4.5,
EC (1:5 H2O) 0.6 dS/m, total P 0.25 %, bicarbonate extractable P 0.5 ppm (Colwell
1963), clay, silt and sand were 4%, 6%, and 90% respectively.
4.2.2 Industrial Byproducts and Reference Fertilizers
The industrial byproducts used in this study were partly burnt chicken litter ash
(CLA), totally burnt chicken litter ash (CLAT), iron smelting slag and wood ash
(WA). CLA was derived from chicken litter burnt in an incinerator for 36 hours at
temperatures between 700oC to 800oC. CLAT was derived from CLA, by heating it
overnight at 700oC to remove residual charcoal from CLA. Slag was a byproduct of a
direct reduction iron making process operated by HIsmelt at the Kwinana
Demonstration Plant, wood ash was derived from the eucalyptus timber and litter used
42
in an experimental bioenergy Power Station at Narrogin Western Australia. Properties
of these materials are given in Table 3.2.
4.2.3 Analysis of industrial byproducts and soil
The alkaline byproducts were chemically analysed for available P using Association
of Official Analytical Chemistry (AOAC) standard methods (AOAC 1975). The
major element content of industrial byproducts was determined by atomic absorption
spectrometry (AAS) and trace element contents by inductively coupled plasma – mass
spectrometry (ICPMS) after perchloric acid digestion. Total P in solution was
determined colorimetrically using the molybdovanadophosphate (yellow) method
(Rayment and Higginson 1992). Analyses are reported in Table 3.3 (Chapter 3).
4.2.4 Glasshouse Experiment
The treatments consisted of various rates of application to the soil of the byproducts
and the reference fertilizers; monocalcium phosphate (MCP), dicalcium phosphate
(DCP) and rock phosphate from Sechura (RP). Levels of phosphate for all sources
included a control (zero rate) and the rates listed in Table 4.1 differ for the different
sources reflecting the various solubilities of these materials.
Table 4.1. Levels of P added to soil for the plant growth experiment
MCP
(mg/kg)
DCP
(mg/kg)
RP
(mg/kg)
CLA
(mg/kg)
CLAT
(mg/kg)
WA
(mg/kg)
Slag (mg/kg)
4.2 8.3 20.8 33.3 18.8 10.4 12.5
8.3 16.7 41.7 66.7 37.5 20.8 25
16.7 33.3 83.3 133.3 75 41.7 50
33.3 66.7 166.7 266.7 150 83.3 100
66.7 133.3 333.3 533.3 300 166.7 200
1.5 kg subsample of air dry <2mm soil was placed in a plastic bag. The basal fertilizer
(Table 4.2) was applied with P fertilizers and the soil was then mixed thoroughly and
incubated at field capacity for 4 days before seeding. Fifty pregerminated seeds of
annual ryegrass (Lolium rigidum Gaud) were placed in the pots at 1 cm depth and
43
thinned to 20 uniform plants per pot after the plants had reached the two-leaf stage.
The treatments were replicated two times and placed in a completely randomised
block design. The pots were rerandomised each 7 days and maintained at constant
weight with deionised water. Ryegrass was harvested after 8 weeks and at 4-week
intervals thereafter. The plants were harvested by cutting the tops at about 1 cm above
the soil surface to allow regrowth and dried at 60oC until constant weight occurred.
Table 4.2 Basal fertilizer and dose per pot used in the glasshouse experiment
Salt MWt Stock Soln (g/L) Aliquot (mL/1.5 kg soil)
NH4NO3 80.04 57 5.01
K2SO4 174.25 42 9.99
CaCL2.2H2O 147.02 90 5.01
MgSO4.7H2O 246.77 24 5.01
MnSO4.H2O 169.01 6 5.01
ZnSO4.7H2O 287.54 5.4 5.01
CuSO4.5H2O 249.68 1.2 5.01
H3BO3 61.83 0.42 5.01
CoSO4.7H2O 281.11 0.16 5.01
Na2Mo4.2H2O 241.95 0.12 5.01
The harvested plant tops were then ground and analysed for P, Ca, Mg, K, Na, S and
trace elements by X-ray fluorescence spectrometry of pressed powder (Rayment and
Higginson 1992). Soil samples were analysed for pH and EC (1:5 H2O), and available
P (Bic P-Colwell 1963) before planting and after the last harvest.
4.2.5 Relative Agronomic Effectiveness
The agronomic effectiveness (RE) of the materials as phosphate fertilizers was
calculated for each of the four harvests, using the yield data. The ratio of the linear
initial slope of the response curve for the fertilizer relative to the slope for
monocalcium phosphate was calculated and it is the value of RE (Bolland and Gilkes
1990). The same procedure was used to calculate RE values based on plant P content
and soil Bic P values.
44
4.3 Results and discussion
4.3.1 Byproduct Characterization
Some characteristics of the industrial byproducts used in the study are provided in
Table 3.2 in the previous chapter. The pH ranged from 9.9 to 12.8 indicating that
these materials could be used to neutralize soil acidity (Cregan et al. 1989). Total P
concentrations of CLA, CLAT, slag and WA were 3.6%, 4.75%, 0.26% and 0.44%
respectively indicating their considerable value as P fertilizers especially as large rates
of application are used for liming agents so that substantial amounts of P will be
applied despite the quite low concentration of P in some byproducts. The water-
soluble phosphorus concentration in the materials was very low to low due to the
nature of the P compounds and to the alkaline pH of the water extracts of the
byproducts (Lindsay 1979). The solubility of P in the byproducts was much higher in
citric acid compare to neutral ammonium citrate and alkaline ammonium citrate. The
higher concentration of phosphorus in CLAT relative to CLA is due to removal of
charcoal from CLA so that recalcitrant and protected forms of P were no longer
present (Chapter 3) (Codling et al. 2002). Other major plant nutrients present in these
byproducts include calcium, magnesium, sodium and potassium. Concentrations of
Cd, As and Cu in CLA and CLAT were moderately elevated, while concentrations of
other trace elements in the byproducts were within the normal range for soils in
Australia (ANZECC/NHMRC 1992) so that use of these materials is unlikely to
contaminate soils.
4.3.2 Soil pH, EC and Bicarbonate P
The effects of the addition of industrial byproducts on pH, EC and Bic P values of the
soil measured after the last harvest are presented in Figure 4.1. MCP, DCP and RP did
not have a liming effect, whereas CLA, CLAT, WA and slag increased soil pH with
each material producing a quite constant increase of pH for all rates of application
rather than a progressive increase in pH with application rate indicating buffering
effect for the compounds (Cregan et al. 1989). WA was the most effective liming
agent and it increased soil pH by about 2.3 units. However for all the treatments soil
pH was in the range of 5.5 to 7.0, which is suitable for ryegrass (Slattery et al. 1999).
45
Soil pH
4
5
6
7
8
1 10 100 1000
Log P Applied (mg/kg)
pH S
oil
Soil pH
Soil EC
0.000.200.400.600.801.001.201.401.60
1 10 100 1000
Log P applied (mg/kg)
EC S
oil (
dS/m
)
Soil EC
Soil Bic P
0
2
4
6
8
10
12
1 10 100 1000
Log P applied (mg/kg)
Bic
P S
oil (
mg/
kg
Soil Bic P
Figure 4.1. Plots of log P applied (mg/kg) versus pH, EC, and Bic P for soil samples
taken after the last harvest: ◆ MCP, ■ DCP, ▲ RP, x Slag, WA, ● CLA, + CLAT
The byproducts contain various amounts of water-soluble salts that could increase soil
salinity at high rates of application. The EC values of the soil at the end of the
46
experiment were low for all the soils with the highest EC value of 1.40 dS/m at the
533 mg/kg rate of CLA being insufficient to affect the growth of ryegrass (Moore
1998). The EC values decreased with the increasing application rate of MCP, DCP
and RP, which may due to the greater uptake of natural and fertilizer salts by the
larger plants that were produced by the higher levels of application of P fertilizers.
The amount of Bic P increased systematically with the increasing rate of fertilizer for
all P sources. The relative effectiveness of the byproducts was calculated from the
linear slopes of the Bic P versus application rate graphs in Figure 4.1. Values of slope
for each P fertilizer were derived by the slope for MCP, which is the reference
fertilizer (RE = 100%). The RE values for DCP and RP were 59% and 40%, while the
RE values for slag, WA, CLA and CLAT were 19%, 29%, 39%, and 45%
respectively.
4.3.3 Plant composition and yield response data
Application of byproducts affected the concentrations of most nutrient elements (Na,
Mg, K, Ca, Si, P, S, Cl, Mn, Cu and Zn) in the plants with both increases and
decreases occurring due to fertilization depending on the nature of the fertilizers
(Appendix 4.1). However nutrient concentrations were within the normal range for
ryegrass so that it is unlikely that element toxicity or deficiency other than that of P
occurred during the experiment (Reuter and Robinson 1997). The appearance of
ryegrass for the highest and the lowest rates of fertilizer application before harvesting
are presented in Appendix 4.2. It is clear from the foliar symptoms that ryegrass
receiving the lowest rates of application experienced severe P deficiency.
For each harvest dry matter yield generally increased with the amount of P applied
indicating the P deficient nature of the soil and the influence of the P fertilizers (Fig.
4.2). Dry matter yield of ryegrass ranged from 0.03 g to 2.37 g/pot, 0.06 g to 2.38
g/pot, 0.12 g to 2.28 g/pot and 0.08 g to 2.81 g/pot respectively for the four harvests.
For harvest III and IV some plants died due to P deficiency for the low P application
rates.
The P concentration (Appendix 4.3) in the plants ranged from 0.01% to 0.1% and
according to the critical values of Reuter and Robinson (1997) this entire range
47
represents deficiency, even for the highest rates of P application. However this
particular ryegrass cultivar (Lolium rigidum Gaud), which is commonly grown on
highly P deficient Western Australian soils, has a very low demand for P so that the
published critical levels (for other ryegrass cultivars) are inappropriate. Snars et al.
(2004) found that concentrations of P in this ryegrass cultivar at sufficiency were
much lower than the published values of Reuter and Robinson (1997).
Harvest 1
0
0.5
1
1.5
2
2.5
1 10 100 1000
Log P applied (mg/kg)
Yie
ld (g
/pot
)
Harvest II
0
0.5
1
1.5
2
2.5
1 10 100 1000
Log P applied (mg/kg)
Yie
ld (g
/pot
)
Harvest III
0
0.5
1
1.5
2
2.5
1 10 100 1000
Log P applied (mg/kg)
Yie
ld (g
/pot
)
Harvest IV
0
0.5
1
1.5
2
2.5
3
1 10 100 1000
Log P applied (mg/kg)
Yie
ld (g
/pot
)
Figure 4.2. Yield (g/pot) versus log rate of P applied (mg/kg) for each harvest for the
seven fertilizers: ◆ MCP, ■ DCP, ▲ RP, x Slag, WA, ● CLA, + CLAT.
The internal efficiency of P utilization by ryegrass is indicated by plots of plant dry
matter versus the P content of plants (Palmer and Gilkes, 1982). For each harvest the
48
existence of a single internal efficiency curve for all P sources (Figure 4.3) indicates
that differences in yield were due predominantly to differences in plant P content as
was also observed by Snars et al. (2004) in an experiment with the same ryegrass
cultivar.
Harvest I
y = 1.25x + 0.090R2 = 0.9977
0
0.5
1
1.5
2
2.5
0 0.5 1 1.5 2
P Content (mg P/pot)
Yiel
d(g
/pot
)
Harvest II
y = 1.69x - 0.14R2 = 0.9964
0
0.5
1
1.5
2
2.5
0 0.5 1 1.5 2
P Content (mg P/pot)
Yiel
d(g
/pot
)
Harvest III
y = 1.39x + 0.03R2 = 0.9928
0
0.5
1
1.5
2
2.5
0 0.5 1 1.5 2
P Content (mg P/pot)
Yie
ld(g
/pot
)
Harvest IV
y = 1.61x + 0.02R2 = 0.9954
0
0.5
1
1.5
2
2.5
3
0 0.5 1 1.5 2
P Content (mg P/pot)
Yiel
d(g
/pot
)
Figure 4.3. Internal efficiency of P utilization curves for each harvest: ◆ MCP, ■
DCP, ▲ RP, x Slag, WA, ● CLA, + CLAT
49
Harvest I
0
0.5
1
1.5
2
1 10 100 1000
Log P applied (mg/kg)
PC
onte
nt(m
g/po
t)
Harvest II
0
0.5
1
1.5
2
1 10 100 1000
Log P applied (mg/kg)
P C
onte
nt (m
g/po
t)
Harvest III
0
0.5
1
1.5
2
1 10 100 1000
Log P applied (mg/kg)
P Co
nten
t (m
g/po
t)
Harvest IV
0
0.5
1
1.5
2
1 10 100 1000
Log P applied (mg/kg)
P Co
nten
t (m
g/po
t)
Figure 4.4. P content versus log P applied for all harvests: ◆ MCP, ■ DCP, ▲ RP, x
Slag, WA, ● CLA, + CLAT
Figures 4.4. show the response curves for P content versus P applied for all the
harvests. There was a large response in P content to MCP, DCP and RP application
for all harvests. For the byproducts there was a much smaller response for harvest I
and II; for harvest III and IV there was no systematic trend in response for the
byproducts. Some plants died before the third harvest for slag, WA and CLAT. The
growth and P content of ryegrass for soil amended with these byproducts may not
simply reflect a response to applied P. For instance the liming effect of these materials
increased soil pH (Turner 1993) and this may have affected the availability of
nutrients, although this is not evident in the plant analyses. Similarly the presence of
50
abundant Ca and other ions in soil solutions due to dissolution of the byproducts in
the soil may have reduced the availability of P (Sample et al. 1980). Plants may have
ceased to grow or died from a combination of P deficiency and the high level of pH in
the soil (Barber, 1980).
4.3.4 Relative Effectiveness (RE)
The agronomic relative effectiveness (RE) of the phosphate fertilizers based on plant
data was derived by comparing the initial slope of response curves for plant yield and
P content for the various materials with the slope for MCP as the reference (Figure
4.5). This is a reliable procedure providing that the yield values are well below the
non P limiting yield plateau (Bolland and Gilkes 1990)
Due to the death after the second harvest of some plants fertilised with WA and
CLAT, no RE values could be calculated for these P sources for the later harvests. For
the last two harvests, application of WA and CLAT as phosphorus fertilizers
produced no systematic responses in yield and P content, so that response curves were
poorly defined (low R2 values) (Appendix 4.4).
The effectiveness of CLA, DCP, and RP relative to MCP showed an increasing trend
with the harvest number. There was a systematic increase in RE values for the first
three harvests of CLA, DCP and RP. It must be stressed that values of RE have been
calculated relative to MCP for which the absolute effectiveness decreases with time
since application (Bolland and Gilkes 1990). Thus despite the increase in RE values,
the absolute effectiveness of the other P fertilizers may not have increased. However
it is evident that chicken litter ash has appreciable rapid effect and a good residual
value as a phosphate fertilizer (Codling et al. 2002) whereas wood ash and slag were
relatively ineffective.
51
Plant Yield
0
20
40
60
80
100
120
1 2 3 4
Harvest
RE (%
)
P Content
0
20
40
60
80
100
120
1 2 3 4
Harvest
RE
(%)
MCP DCP RP Slag WA CLA CLAT
Figure 4.5. RE values for the byproducts based on yield and P content for the four
harvests
4.4 Conclusion
The results of this study provide strong evidence that chicken litter ash is a
moderately effective P fertilizer but that it is inferior to MCP, DCP and RP. Slag and
WA were relatively poor sources of P probably due to the alkaline pH of the
materials, which would have reduced the solubility of P in soil solution. However as
52
CLA, CLAT, slag and WA have excellent liming value and as they would be applied
at much higher rates as lime than are used for fertilizers it is likely that all four
materials will provide substantial additional P to plants. They may be more suited for
use on permanent pastures or for tree crops where a rapid response to P fertilizer
application is less important than is the case for fast growing cereals or horticultural
crops.
53
Chapter 5
5.0 General Summary, Limitations and Future Work
5.1 General Summary The main purposes of the research as discussed in the general introduction were to
characterize iron-smelting slag, wood ash and chicken litter ash and evaluate the use
of these materials as liming agents and sources of P for agricultural land in Western
Australia. The main findings of the study were that the byproducts differ in
mineralogy, morphology and chemistry. They provide P to plants and effectively
ameliorate acid soils.
The byproducts used in the study were chicken litter ash burnt at several temperatures,
partly burnt chicken litter ash, totally burnt chicken litter ash, wood ash, and iron
smelting slag. The pH of all the materials were above 9 and calcium carbonate
equivalence values were above 90%, indicating that these materials will be effective
liming agents. Chicken litter ash contains more than 3% total P while the values for
slag and WA were above 0.25%. Other plant nutrients present in byproducts include
calcium, magnesium, sodium, potassium and trace elements.
For calcined chicken litter, the amount of P dissolved by citrate extractants varied
with the extractant and calcination temperature. The P dissolved for short and long
periods of extraction of the various calcines increased followed the sequence
CA>NAC>AAC. The amounts of soluble P in CLA and CLAT also followed the
sequence CA>NAC>AAC with little additional dissolution after 6 hours of extraction.
Dissolution of P in WA was quite rapid for all the three extractants while P in slag
dissolved slowly and at slower rate for NAC and AAC compared to CA.
CLA, and CLAT were consisted of mixtures of apatite, calcite, and quartz together
with much charcoal in CLA. The intensity and the sharpness of apatite XRD
reflection for chicken litter ash increased with increased calcination temperature.
Apatite persisted in the three extractant residues and followed the sequence
CA<NAC<AAC. SEM micrographs before and after the extractions provided
54
explanations for the chemical and XRD analysis. Some grains micrographs consist
mostly of carbon but also contain P and cations.
The minerals presents in RP were apatite and quartz and much apatite persisted in the
residues for all three extractants. WA consisted mostly of calcite and quartz, with no
apatite being observed. Calcite in WA dissolved in CA but remained in NAC and
AAC residues. Calcium magnesium silicate (akermanite) and calcium aluminium
silicate (gehlenite) were the main constituents of slag. CA dissolved much akermanite
and lesser gehlenite in slag, while NAC and AAC dissolved less of both compounds.
In the glasshouse experiment all P sources produced initial yield responses but for
iron smelting slag and wood ash, many plants died of P deficiency before the third
harvest. Based on plant yield data, the relative effectiveness (RE) of DCP compared
to MCP was 57%, 72%, 73%, and 94 % respectively for four harvests, for RP was
24%, 34%, 70% and 56%, for chicken litter ash was 13%, 16%, 33% and 39%, for
slag was 8%, 9%, 16% and 10%, for WA was 6%, 9% and effectively zero for the
final two harvests. Thus chicken litter ash could be used as a P fertilizer but it is less
effective than MCP. Iron smelting slag and wood ash were much less effective
fertilizers but may still provide significant amount of P to plant where large
application of these materials are used as liming agents. Application of the byproducts
increased the pH of the soil.
Chicken litter ash is a moderately effective P fertilizer but inferior to DCP and RP.
Slag and WA were relatively poor sources of P. However as CLA, CLAT, slag and
WA have a liming action and would be applied at much higher rate than are used for
fertilizers it is likely that all four materials will provide additional P to plants.
5.2 Limitation and Future Works
This research has several limitations and further research is needed. For example, the
study was based on laboratory and glasshouse research and it is important that the
assessment of industrial byproducts be carried out under field conditions. Importantly,
an economic analysis including cost-benefit evaluation of the use of the byproducts
needs to be carried out.
55
Application of the industrial byproducts in large amounts to large areas of agricultural
land has the potential to create unanticipated environmental problems. For example if
the materials, especially in finely ground and ash form are used at a large scale there
may be a dust problem that could be dangerous for human and animal respiratory
systems. It may be possible to combine the byproducts with compost or other
materials to reduce dust and possibly to increase the effectiveness of the byproducts.
The glasshouse experiment to evaluate the agronomic effectiveness of the byproducts,
was based on ryegrass which has a low P demand. A next step would be to study the
effectiveness of the byproducts for cereals and other species with diverse P
requirements (e.g. plantation forestry).
This research has clearly demonstrated the value of byproducts as combined P
fertilizers and liming agents. In view of the large amounts of these materials that will
be produced in future years, there is a clear opportunity for integrating the materials
into appropriate land management practices.
56
Chapter 6 6.0 Publications from this thesis
Conferences Publications
Yusiharni, B. E., and Gilkes, B. 2006. The Use of Industrial Byproducts as Liming
Agents And Phosphate Fertilizers. Proceedings The 18th World Congress of Soil
Science, Philadelphia USA, 8-15 July 2006.
Yusiharni, B. E., and Gilkes, B. 2006. Mineralogy of Chicken Poo. Proceedings
AXAA/WASM 2006 Conference, Margaret River, Western Australia, 22-24
September 2006.
Yusiharni, B. E., and Gilkes, B. 2006. Chicken Litter Ash: An Evaluation of an
Agronomic Resource. Reviewed Conference. Proceedings ASSSI - ASPAC National
Soils Conference, Soil Science Solving Problems. The University of Adelaide
North Terrace 3-7 December 2006.
Journals Publications
Chapter 3
Yusiharni, B. E., Gilkes, R. J., and H. Ziadi., 2006. A laboratory evaluation of chicken
litter ash, iron smelting slag and wood ash. In press. Aust. J. of Soil. Res.
Chapter 4
Yusiharni, B. E., Gilkes, R. J., 2006. An evaluation as phosphorus fertilizers of the
byproducts: chicken litter ash, iron smelting slag and wood ash. Submitted to Aust. J.
Agric. Res.
57
References Adams, F., 1984, Soil acidity and liming, 2nd edn., Wisconsin: American Society of
Agronomy, 57-59 Alloway, B. J., Ayres, D.C., 1993, Chemical principles of environmental pollution.
Blackie Academic Professional, an imprint of Chapman & Hall. Alvarez, J., Snyder, G. H., Anderson, D. L., Jones, D. B., 1988, Economics of calcium
silicate slag application in a rice-sugarcane rotation in the everglades, Agricultural Systems, 28:179-188.
Anderson, D.L., Kussow, W.R., Corey, R.B., 1985. Phosphate rock dissolution in
soil: Indications from plant growth studies. Soil Science Society of America Journal, 49, 918-925.
Anderson, D. L., Snyder, G. H., and Martin, F. G., 1991, Multi-year response of
sugarcane to calcium silicate slag on everglades Histosols, Agron. J., 83:870-874. ANZECC/NHMRC, 1992, Australian and New Zealand guidelines for the assessment
and management of contaminated sites. Australia and New Zealand Environment and Conservation Council/National Health and Medical Research Council: Canberra.
Association of Official Agricultural Chemists, 1975, Association of Official
Agricultural Chemists, Official Methods of Analysis.’12th Edn. AOAC: Washington.
Barber, S. A., 1984, Liming materials and practices, In Ed. F. Adams, Soil Acidity and
Liming 2nd Edition, Wisconsin; American Society of Agronomy, 171-210 Barber, S.A., 1980, Soil-plant interactions in the phosphorus nutrition of plants. In
The Role of Phosphorus in Agriculture. 1st Ed. Soil Science Society of America, Madison, Wisconsin, USA.
Barker, A.V., O’Brien, T. A., and Stratton, M. L., 2000, Description of food
processing by-products, pp. 63-106, In ‘Land Application of Agricultural, Industrial, and Municipal By-Products’, (Eds. J. F. Power and W. A. Dick)., Soil Science Society of America. Book series No 6
Bear, F. E., 1969, Chemistry of The Soil, Second edition, American Chemical society
Monograph Series, 292-319 Bolan, N., 2004, Basics on basic slag, available on
http://soilsearth.massey.ac.nz/cybsoil/article/slag.htm [accessed on 27 August 2004]
Bolland, M.D. A. , Gilkes, R.J., 1990, The poor performance of rock phosphate
fertilizers in Western Australia: Part 1. The crop and pasture response. Agricultural Science, 3: 8-43
58
Boxma, R., 1977, Evaluation of phosphate in fertilizers by means of the alkaline ammonium citrate extraction according to Petermann. Neth. J. Agric. Sci. 25: 42-50.
Clapham, W. M., and Zibilske, L. M., 1992, Wood ash as a liming amendment,
Commun., Soil Sci., Plant Anal., 23, 1209-1227 Clark, R. B., 1982, Plant response to mineral element toxicity and deficiency. In ‘Eds.
M. N. Christiansen and C. F. Lewis, Breeding plants for less favourable environments, John Wiley and Sons, Inc, New York, p. 71-142
Codling, E.E., Rufus, L.C., Sherwell, J., 2002, Poultry litter ash as a potential
phosphorus source for agricultural crops. Journal of Environmental Quality, 31: 954-961
Colwell, J.D., 1963, The estimation of the phosphorus fertilizer requirements of wheat
in southern New South Wales by soil analysis. Australian Journal of Experimental Agriculture and Animal Husbandry, 3:190–197
Coventry, D. R., 1985, Changes in agricultural systems on acid soils in southern
Australia, Australian Agronomy conference, Proceedings, 45-126. Cregan, P. D., Hirth, J. R., and Conyers, M. K., 1989, Amelioration of soil acidity by
liming and other amendments. In ‘Ed. A. D. Robson, Soil Acidity and Plant Growth, Sydney, Academic Press, 205-264
Demeyer, A., Nkana, J. C. V., and Verloo, M. G., 2001, Characteristics of wood ash
and influence on soil properties and nutrient uptake: an overview, Bioresource Technology, 77: 287-285.
Doak, B. W, Gallaher, P. J., Evans, L., Muller, F. B., 1965, Low temperature
calcination of C-grade phosphate from Christmas Island. N. Z. J. Agric. Res. 8: 15-29
Etiegni, L., Campbell, A. G., and Mahler, R. L., 1991, Evaluation of wood ash
disposal on agricultural land. I. Potential as a soil additive and liming agent, Commun. Soil Sci. Plant Anal, 22, 243-256.
Evans, G., 1991, Acid soils in Australia, Bureau of Rural Resources, Department of
Primary Industries and Energy: Canberra, p: 4 Fibrophos, 2006, available on www.fibrophos.co.uk [accessed on 2 May 2006] Foy, C. D., 1984, Physiological effects of hydrogen, aluminium and manganese
toxicities in acid soil, In Pearson, R. W., Adams, F., eds., Soil acidity and liming, 2nd edn., Wisconsin: American Society of Agronomy, 57-59
Francis, A. A., and Youssef, N. F., 2004, Glass ceramic from industrial waste
materials. Scandinavian Journal of Metallurgy, 33: 236-241.
59
Gilkes, R. J., Palmer, B. 1979. Calcined Christmas island C-grade rock phosphate
fertilizers: Mineralogical properties, reversion and assessment by chemical extraction. Australian Journal of Soil Research. 17: 467– 481.
Gilkes, R. J., Rate, A. W., Hinz, C. and Aylmore, L. A. G., 2003, Soil science 230-
laboratory manual. Soil Science Group, School of Earth and Geographical Sciences, The University of Western Australia, pp:71-72
Harper, R.J., Gilkes, R.J., Robson, A.D., 1982. Biocrystallization of quartz and
calcium phosphates in plants- a re-examination of the evidence. Aust. J. Agric. Res 33, 565-571.
Heckman, J. R., 2000, Agricultural liming materials, available on
www.rce.rutgers.edu. [accessed on 29 July 2004] Helyar, K. R., and Porter, W. M., 1989, Soil acidification its measurement and the
processes involved. In Ed. A. D. Robson, Soil Acidity and Plant Growth, Sydney, Academic Press, 61-102
Hughes, J. C., Gilkes, R. J. 1984. The effect of chemical extractant on the estimation
of rock phosphate fertilizer dissolution. Aust J. Soil Research. 22: 475-481. Humphreys, G.S., Hunt, P.A., Buchanan, R., 1987. Wood ash stone near Sydney, N.
S. W.: A carbonate pedological feature in an acidic soil. Aust J. Soil Research 25, 115-124.
Kalyoncu, R. S., 1998, Slag-iron and steel, available on http://www.scirus.com.
[accessed on 5 July 2004] Kato, N. and Owa, N., 1997a, Dissolution of slag fertilizers in paddy soil and Si
uptake by rice plant, Soil Science & Plant Nutrition, 43(2): 329-341 Kato, N., Yanagisawa, K. and Owa, N., 1997, Measurement of Si adsorption and
“active Si” in a soil amended with slag fertilizers by using stable isotope Si. Soil science & Plant Nutrition, 43: 623-631
Kauffman, M. D., 1977, The effect of soil acidity and lime placement on root growth
and yield of winter wheat and alfalfa, Ph.D. Diss. Oregon State Univ., Corvallis. Diss. Abstr. 37B:7.3192-3193
Khan, H. Rahman, S., Hussain, M. S., and Adachi, T., 1994, Growth and yield
response of rice to selected amendments in an acid sulphate soil, Soil Science and Plant Nutrition, 40:231-242
Khasawneh, F. E., Doll, E. C., 1978. Increasing the productivity of Brazilian cerrado
soils. Proc. Int. Seminar on Soil Environ. Fertil. Manage. In Intensive Agric, Tokyo, Japan. pp. 462-471.
60
Khasawneh, F.E., Sample, E.C., Kamprath, E.J., 1980. Role of Phosphorus in Agriculture. 1st Ed. Soil Science Society of America, Madison, Wisconsin, USA.
Kinraide, T. B., 1991, Identity of the rhizotoxic aluminium species, Plant Soil,
134:167-178 Klug, H.P., Alexander, L.E., 1974. X-ray diffraction procedures for polycrystalline &
amorphous materials. 2nd ed. John Wiley & Sons Inc, New York. Lee, A. R., 1974, Blastfurnace and steel slag, Edward Arnold., London, 119 pp. Lehr, J.L., 1980. Phosphate raw materials and fertilizers: Part I-a look ahead. In The
Role of Phosphorus in Agriculture. 1st Ed. Soil Science Society of America, Madison, Wisconsin, USA.
Lim, H.H., Gilkes, R.J., 2001. Beneficiation of apatite rock phosphate by calcination:
effects on chemical properties and fertiliser effectiveness. Aust. J. Soil. Res 39, 397-402.
Lindsay, W.L., Paul, L.G.V., Chien, S.H., 1989. Phosphate minerals. In Minerals in
soil environments. 2nd ed. (Eds). Soil Science Society of America, Madison, Wisconsin, USA.
Leonard, L., and Boland, M., 1995, Soil acidity- a reference manual, Agriculture
Western Australia, Perth Lerner, B. R., and Utzhinger, J. D., 1986, Wood ash as soil liming material.
HortScience, 21 (1): 76-78 Li, J., and Gilkes, R. J., 2002, Summary of the first stage experimental results for
environmental uses of HIsmelt slag, Report to HIsmelt, Unpublished, The University of Western Australia
Lindsay, W.L., 1979, Phosphorus. In Chemical equilibria in soils. pp. 169-209. Wiley
Interscience: New York Male, D. W., Leduc, L. G., and Ferroni, G. D., 1997, The potential of mining slag as a
substrate for microbial growth and the microbiological analysis of slag and slag seepage, Kluwer Academic publisher, Antonie van Leeuwenhock
71:379-386 Mbaherekire, B. J., Oryem-origa, H., Kashambuzi, J., Mutumba, G. M., and
Nyangababo, J. T., 2003, Elemental composition of bean (Phaseolus vulgaris) and soy bean (Glycine max L.) grown on wood ash amended soil, Bull. Environ. Contam. Toxicol, 70: 817-823.
McArthur, W.M., 1991, Reference soils of south-Western Australia. ASSS (W.A.
Branch). Perth
61
McClellan, G.H., Gremillion, G.H., 1980. Evaluation of phosphatic raw materials. In The Role of Phosphorus in Agriculture. 1st Ed. Soil Science Society of America, Madison, Wisconsin, USA.
Miller, A., Lime use in Western Australia, 2002, Western Australia Soil Acidity
Research and Development update 2001, Department of Agriculture, Western Australia
Miller, D. M., Miller, W. P., O’Brien, T. A., and Sumner, M. E., 2000,
Characterization of Industrial by-products. pp. 107-126, In ‘Land Application of Agricultural, Industrial, and Municipal By-Products’, (Eds. J. F. Power and W. A. Dick)., Soil Science Society of America. Book series No 6
Moore, G., 1998, Soil Guide. A handbook for understanding and managing
agricultural soils’. Department of Agriculture, Western Australia. Bulletin No. 4343. pp. 318
Nkana, J. C. V., Demeyer, A., and Verloo, M. G., 2002, Effect of wood ash
application on soil solution chemistry of tropical acid soils: incubation study. Bioresource Technology, 85: 323-325
Onderwater, M,Z., Backman, R., Skrifvars, B.J., and Hupa, M., 2001, The ash
chemistry in fluidised bed gasification of biomass fuels. Part I: predicting the chemistry of melting ashes and ash-bed material interaction. Fuel, 80:1489-1502
Palmer, B., and Gilkes, R.J., 1982, Reversion of calcined calcium aluminium
phosphate fertilizers due to rehydroxylation of crandallite. Aust. J. Soil Res, 20:243-250
Penny, S. A., 2002, Methods of lime storage and stabilisation, Farmnote, Soil acidity
Series, Department of Agriculture, Western Australia Perkiomaki, J., 2004, Wood ash use in coniferous forests, a soil microbiological study
into the potential risk of cadmium release, Metsantutkimuslaitoksen Tiedonantoja 917, Finish Forest Research Institute, Research Papers 917
Porter, W. M., 1981, Soil acidification - the cause, available on
http://www.regional.org.au/au/roc/1981/roc198131.htm, [accessed on 3 August 2004]
Pote, D.H., Kingery, W.L., Aiken, G.E., Han, F.X., Moore, P.A., and Buddington, K.,
2003, Water-quality effects of incorporating poultry litter into perennial grassland soils. J. Environ. Qual, 32:2392-2398
Power Plant Research Program, 1998, Engineering and economic feasibility of using
poultry litter as a fuel to generate electric power at Maryland’s Eastern Correctional Institute.PPES–96-1. Department of Natural Resources Annapolis, MD, America.
62
Rayment, G.E., Higginson, F.R., 1992, Australian laboratory handbook of soil and water chemical methods. Inkata Press: Melbourne
Reuter, D.J., Robinson, J.B., 1997, Plant analysis: an interpretation manual.’2nd edn
CSIRO Publishing: Melbourne Ritchie, G. S. P., 1989, The chemical behaviour of aluminium, hydrogen and
manganese in acid soils. In Ed. A. D. Robson, Soil Acidity and Plant Growth, Sydney, Academic Press, 1-60
Robson, A. D., and Abbott L. K., 1989, The effect of soil acidity on microbial activity
in soils. In Ed. A. D. Robson, Soil Acidity and Plant Growth, Sydney, Academic Press, 139-166
Rodriguez, M., Lopez, F. A., Pinto, M., Balcazar, N., and Besga, G., 1994, Basic
Linz-Donawitz slag as a liming agent for pastureland. Agron. J. 86,904-909 Rumpf, S., Ludwig, B., and Mindrup, M., 2001, Effect of wood ash on soil chemistry
of a pine stand in Northern Germany. J. Plant. Nutr. Soil Sci. 164, 569-575 Russell, E. W., 1988, Soil conditions and plant growth, Ed. A. Wild, New York, John
Wiley and Sons, 844-898 Samac, D. A., and Tesfaye, M., 2003, Plant improvement for tolerance to aluminium
in acid soils- a review. Plant Cell, Tissue and Organ Culture, 75:189-207 Sample, E.C., Soper, R.J., and Racz, G.J., 1980, Reactions of phosphate fertilizers in
soils. In The Role of Phosphorus in Agriculture. 1st Ed. Soil Science Society of America, Madison, Wisconsin, USA.
Sander, M.S., Andren, O., 1997. Ash from cereal and rape straw used for heat
production: Liming effect and contents of plant nutrients and heavy metals. Water, Air, and Soil Pollution, 93, 93-108.
Seatz, L. F., Peterson, H. B., 1969, Acid, alkaline, saline, and sodic soils. In Ed. F. E.
Bear, Chemistry of The Soil, Second edition, American Chemical Society Monograph Series, 292-319
Sims, J. T., Pierzynski, G. M., 2000, Assessing the impacts of agricultural, municipal,
and industrial by-products on soil quality, pp. 237-288, In ‘Land Application of Agricultural, Industrial, and Municipal By-Products’, (Eds. J. F. Power and W. A. Dick)., Soil Science Society of America. Book series No 6
Slattery, W. J., Conyers, M. K., and Aitken, R. L., 1999, Soil pH, aluminium,
manganese and lime requirement, In Eds. K. I. Peverill, L. A. Sparrow, D. J. Reuter, Soil Analysis an Interpretation Manual, CSIRO Publishing; Victoria, 103-128
63
Snars, K., Hughes, J.C., and Gilkes, R.J., 2004, The effects of addition of bauxite red mud to soil on P uptake by plants. Australian Journal of Agricultural Research, 55: 25-31
Snyder, G. H., Jones, D. B., and Gascho, G. J., 1986, Silicon fertilization of rice on
everglades Histosols, J. Soil Sci, Soc. Am, 50, 1259-1263 Spies, C. D., and Harms, C. L., 2004, Soil acidity and liming of Indiana soils,
available on http://www.agry.purdue.edu/ext/forages/publications/ay267.htm, [accessed on 5 August 2004]
Tan, K. H., 1994, Environmental soil science, p: 218-251, Marcel Dekker, Inc, New
York Tan, K. H., 1998, Principles of soil chemistry, p: 363, 3rd ed. Marcel Dekker, Inc,
New York The Australian Agriculture Assessment 2001 Report, 2001, available on
www.nlwra.gov.au [accessed on 15 Oct 2004]. Thomas, G. W., and Hargrove, W. L., 1984, The chemistry of soil acidity. In Ed. F.
Adams, Soil Acidity and Liming, Second Edition, American Society of Agronomy, Inc, 3-56
Thompson, J., 2004, Managing soil acidity, available on
http://www.soil.ncsu.edu/lockers/Thompson_J/ssc012/Lecture/Oy_Liming.htm [accessed on 28 July 2004)
Turner TR (1993) Turfgrass. In ‘Nutrient deficiencies & toxicities in crop plants’.
(Ed: Bennett WF). pp. 187 – 196. APS Press, The Am. Phytopath. Soc.: St Paul Minnesota
Vance, E. D., and Mitchell, C. C., 2000, Beneficial use of wood ash as an agricultural
soil amendment: Case studies from the United States forests products industry. In Land Application of Agricultural, Industrial, and Municipal By-Products, (Eds. J. F. Power and W. A. Dick), Soil Science Society of America, Book series no 6, 567-582
White, M.S., 1971. Calcination of Christmas Island phosphate. N. Z. J. Sci 14, 971-
992. Whitney, D. A., and Lamond, R. E., 1993, Liming acid soils, Kansas State University,
Agricultural Experiment Station and Cooperative Extension Service, available on http://www.oznet.ksu.edu/library/CRPSL2/MF1065.Pdf, [accessed on 12 August 2004)
Yusiharni, B. E., Gilkes, R. J., 2006. An evaluation as phosphorus fertilizers of the
byproducts: Chicken litter ash, iron smelting slag and wood ash. Submitted to Aust. J. Agric. Res.
64
Appendix 4.1.1 XRF Analysis of Plant Dry Tops for Harvest 1
Na Mg K Ca Si S Cl Mn Fe Cu Zn Rate of P Applied (mg/kg) (%) (%) (%) (%) (%) (%) (%) (ppm) (ppm) (ppm) (ppm)
0 0.18 0.49 2.10 0.87 0.72 0.51 0.90 202 742 12 60
MCP 4.17 0.16 0.47 1.89 0.82 0.79 0.33 1.00 146 693 9 50
MCP 8.33 0.17 0.51 1.75 0.82 0.80 0.38 1.09 130 635 12 26
MCP 16.67 0.16 0.43 2.30 0.74 0.75 0.32 0.87 132 926 9 28
MCP 33.33 0.11 0.41 2.89 0.68 0.82 0.37 0.74 116 475 12 42
MCP 66.67 0.07 0.28 2.74 0.48 0.46 0.27 1.11 70 524 5 30
DCP 8.33 0.20 0.42 1.77 0.75 0.80 0.36 0.57 148 476 12 54
DCP 16.67 0.17 0.52 2.28 0.90 0.84 0.39 1.23 163 543 16 61
DCP 33.33 0.14 0.48 2.56 0.77 0.82 0.36 0.99 132 428 10 49
DCP 66.67 0.09 0.30 3.01 0.53 0.61 0.28 0.49 84 232 8 34
DCP 133.33 0.04 0.32 2.67 0.51 0.55 0.25 0.86 71 147 8 31
RP 20.83 0.14 0.35 1.26 0.59 0.57 0.23 0.70 90 396 8 28
RP 41.67 0.14 0.54 1.93 0.85 0.88 0.34 1.12 146 884 10 40
RP 83.33 0.13 0.42 2.11 0.71 0.85 0.32 0.76 118 860 9 34
RP 166.67 0.09 0.33 2.33 0.57 0.56 0.27 0.68 85 406 8 34
RP 333.33 0.08 0.30 2.99 0.47 0.49 0.29 0.83 90 127 6 33
Slag 12.50 0.21 0.53 1.75 0.88 0.89 0.35 1.16 160 694 13 52
Slag 25 0.19 0.53 1.67 0.87 0.92 0.33 1.21 154 1470 16 44
Slag 50 0.16 0.40 1.70 0.80 0.93 0.32 0.82 206 1356 28 46
Slag 100 0.27 0.53 1.97 0.92 0.99 0.38 1.11 162 1824 25 37
Slag 200 0.17 0.45 1.67 0.82 1.30 0.32 0.98 184 3056 20 40
WA 10.42 0.29 0.49 1.91 0.78 0.80 0.35 1.03 162 647 8 40
WA 20.83 0.23 0.54 2.04 0.94 0.90 0.39 1.06 215 615 20 50
WA 41.67 0.15 0.42 1.58 0.73 0.88 0.33 0.78 128 595 12 52
WA 83.33 0.21 0.46 1.80 0.79 1.04 0.38 0.89 134 434 8 42
WA 166.67 0.31 0.57 1.91 0.89 0.92 0.35 1.10 151 1028 8 43
CLA 33.33 0.22 0.49 1.68 0.79 0.70 0.35 1.08 128 848 16 34
CLA 66.67 0.14 0.37 1.64 0.76 1.22 0.37 0.68 142 932 12 40
CLA 133.33 0.15 0.41 2.00 0.74 1.00 0.33 0.77 122 912 16 42
CLA 266.67 0.13 0.46 2.37 0.77 0.75 0.36 0.85 113 464 12 50
CLA 533.33 0.10 0.36 2.88 0.67 0.74 0.35 0.64 91 229 10 53
CLAT 18.75 0.25 0.55 1.61 0.86 1.30 0.39 1.04 170 2180 15 40
CLAT 37.50 0.32 0.48 1.54 0.86 1.04 0.35 0.94 140 799 4 33
CLAT 75 0.17 0.43 1.42 0.66 0.88 0.31 0.79 146 872 12 68
CLAT 150 0.44 0.52 2.02 0.83 0.85 0.33 1.12 125 330 1 40
CLAT 300 0.15 0.55 2.32 0.93 0.90 0.37 1.15 118 630 15 52
65
Appendix 4.1.2 XRF Analysis of Plant Dry Tops for Harvest 2
Na Mg K Ca Si S Cl Mn Fe Cu Zn Rate of P Applied (mg/kg) (%) (%) (%) (%) (%) (%) (%) (ppm) (ppm) (ppm) (ppm)
0 0.26 0.58 2.59 1.07 0.77 0.60 1.34 248 716 18 70
MCP 4.17 0.17 0.43 2.84 0.79 0.64 0.57 0.98 208 221 9 52
MCP 8.33 0.23 0.51 2.58 0.82 0.71 0.58 1.24 197 338 15 66
MCP 16.67 0.18 0.48 2.88 0.74 0.63 0.52 1.07 203 284 11 56
MCP 33.33 0.16 0.40 3.35 0.56 0.53 0.49 1.09 194 89 9 44
MCP 66.67 0.12 0.33 2.68 0.50 0.50 0.30 1.59 174 104 6 38
DCP 8.33 0.23 0.46 2.93 0.81 0.78 0.63 0.75 211 516 16 73
DCP 16.67 0.20 0.51 3.29 0.83 0.69 0.66 1.18 225 491 16 72
DCP 33.33 0.15 0.45 3.03 0.73 0.54 0.52 1.08 221 128 11 66
DCP 66.67 0.11 0.32 3.01 0.46 0.49 0.36 1.21 123 74 8 34
DCP 133.33 0.08 0.32 2.50 0.50 0.52 0.26 1.52 157 110 7 30
RP 20.83 0.17 0.52 2.70 0.93 0.66 0.56 1.22 208 540 12 72
RP 41.67 0.20 0.52 2.89 0.81 0.65 0.61 1.14 223 279 14 79
RP 83.33 0.14 0.41 2.86 0.68 0.64 0.52 0.85 202 171 9 56
RP 166.67 0.17 0.35 3.02 0.55 0.56 0.49 1.05 190 121 6 48
RP 333.33 0.09 0.31 2.70 0.44 0.41 0.31 1.29 168 96 7 39
Slag 12.50 0.27 0.54 2.56 0.98 0.82 0.59 1.14 212 259 14 62
Slag 25 0.27 0.57 2.40 0.96 0.75 0.49 1.41 232 1068 20 64
Slag 50 0.31 0.50 2.33 0.93 0.79 0.51 1.13 242 750 22 66
Slag 100 0.26 0.60 2.42 1.03 0.90 0.55 1.36 258 1412 20 66
Slag 200 0.29 0.55 2.34 0.92 0.82 0.50 1.32 236 974 16 64
WA 10.42 0.21 0.52 2.47 0.83 0.75 0.60 0.96 256 882 22 74
WA 20.83 0.34 0.59 2.63 0.99 0.82 0.56 1.28 228 594 12 54
WA 41.67 0.23 0.44 2.73 0.79 0.66 0.56 0.96 213 607 22 69
WA 83.33 0.27 0.64 2.45 1.04 0.66 0.53 1.60 240 624 23 75
WA 166.67 0.28 0.62 2.89 1.02 0.73 0.57 1.40 246 448 16 64
CLA 33.33 0.20 0.48 2.80 0.85 0.73 0.64 1.04 218 231 12 76
CLA 66.67 0.17 0.45 2.95 0.80 0.75 0.60 0.95 225 278 14 75
CLA 133.33 0.15 0.44 2.97 0.38 0.78 0.55 1.03 224 180 13 83
CLA 266.67 0.19 0.46 3.24 0.81 0.73 0.59 1.01 218 147 12 73
CLA 533.33 0.12 0.36 3.23 0.58 0.66 0.63 0.83 192 128 13 63
CLAT 18.75 0.30 0.59 2.58 1.07 0.82 0.59 1.60 260 758 18 74
CLAT 37.50 0.20 0.50 2.50 0.87 0.91 0.56 1.13 252 1392 22 62
CLAT 75 0.38 0.65 2.55 1.06 0.74 0.55 1.49 232 552 12 66
CLAT 150 0.22 0.55 2.80 0.97 0.78 0.60 1.30 227 335 14 79
CLAT 300 0.23 0.51 3.11 0.86 0.73 0.59 1.13 196 257 13 70
66
Appendix 4.1.3 XRF Analysis of Plant Dry Tops for Harvest 3
Na Mg K Ca Si S Cl Mn Fe Cu Zn Rate of P Applied (mg/kg) (%) (%) (%) (%) (%) (%) (%) (ppm) (ppm) (ppm) (ppm)
0 0.68 1.30 2.84 2.15 0.45 0.42 4.29 467 187 11 98
MCP 4.17 0.47 0.83 2.99 1.31 0.54 0.48 2.65 385 100 13 75
MCP 8.33 0.40 0.70 2.63 1.05 0.64 0.49 2.36 356 97 15 92
MCP 16.67 0.54 0.79 2.80 1.15 0.67 0.46 2.77 342 96 14 65
MCP 33.33 0.45 0.72 3.37 0.90 0.51 0.45 2.84 342 113 11 59
MCP 66.67 0.50 0.68 2.80 0.80 0.54 0.48 2.84 318 129 7 20
DCP 8.33 0.44 0.80 2.81 1.28 0.68 0.58 1.73 410 119 12 78
DCP 16.67 0.84 1.10 3.55 1.55 0.75 0.51 3.81 381 112 13 72
DCP 33.33 0.46 0.74 3.13 1.04 0.52 0.43 2.64 381 98 14 77
DCP 66.67 0.28 0.50 2.64 0.55 0.41 0.38 2.04 277 84 7 46
DCP 133.33 0.20 0.48 2.81 0.56 0.50 0.47 1.97 298 94 10 61
RP 20.83 0.37 0.76 2.88 1.19 0.65 0.54 2.15 360 134 10 64
RP 41.67 0.55 0.85 2.85 1.24 0.56 0.49 2.64 360 106 14 74
RP 83.33 0.25 0.72 2.98 0.95 0.53 0.54 2.33 347 152 10 68
RP 166.67 0.64 0.71 2.93 0.77 0.46 0.33 3.06 305 112 15 69
RP 333.33 0.27 0.50 2.94 0.55 0.43 0.45 2.19 300 77 10 63
Slag 12.50 0.73 1.01 2.75 1.59 1.00 0.47 3.02 336 508 11 39
Slag 25 0.99 1.49 3.35 2.45 0.84 0.60 4.59 475 190 10 70
Slag 50 1.62 1.56 3.31 2.33 1.32 0.49 4.78 500 590 10 60
Slag 100 1.05 1.20 3.23 1.99 0.66 0.42 3.94 385 295 15 70
Slag 200 0.88 1.27 2.99 2.05 0.78 0.40 3.91 402 195 10 71
WA 10.42 0.76 0.88 2.93 1.31 0.62 0.51 2.69 390 129 5 44
WA 20.83 1.32 1.43 3.32 2.29 0.72 0.44 4.56 510 510 20 80
WA 41.67 0.80 1.06 3.41 1.70 0.57 0.42 3.78 400 216 14 76
WA 83.33 0.75 0.92 2.75 1.47 0.82 0.49 2.98 389 558 16 90
WA 166.67 0.82 1.41 3.28 2.12 0.73 0.36 4.39 482 364 18 80
CLA 33.33 0.44 0.81 2.78 1.27 0.65 0.49 2.28 301 114 10 83
CLA 66.67 1.15 1.23 3.30 1.75 1.25 0.52 3.53 450 215 15 70
CLA 133.33 0.73 0.74 2.82 1.20 0.66 0.57 2.29 245 115 10 50
CLA 266.67 0.69 0.96 2.94 1.31 0.62 0.46 3.15 379 158 12 82
CLA 533.33 0.65 0.72 2.93 1.36 0.54 0.50 2.58 326 82 14 80
CLAT 18.75 1.54 1.53 3.48 2.21 0.85 0.54 4.87 440 230 10 30
CLAT 37.50 0.99 1.00 3.14 1.46 0.73 0.44 3.44 402 120 6 60
CLAT 75 0.95 1.22 2.97 1.92 0.80 0.51 3.34 408 484 16 90
CLAT 150 0.58 1.17 2.67 1.73 0.80 0.45 3.37 390 183 16 104
CLAT 300 1.24 1.26 3.40 1.92 0.66 0.35 5.19 374 271 13 77
67
Appendix 4.1.4 XRF Analysis of Plant Dry Tops for Harvest 4
Na Mg K Ca Si S Cl Mn Fe Cu Zn Rate of P Applied (mg/kg) (%) (%) (%) (%) (%) (%) (%) (ppm) (ppm) (ppm) (ppm)
0 0.30 0.63 1.75 1.09 0.34 0.26 2.09 218 264 7 39
MCP 4.17 0.49 1.29 3.56 2.03 0.53 0.52 4.02 495 253 15 84
MCP 8.33 0.73 1.42 3.73 2.27 0.58 0.57 4.96 555 285 19 89
MCP 16.67 0.79 1.30 4.07 2.06 0.60 0.70 4.89 537 380 13 79
MCP 33.33 0.49 1.43 3.69 1.68 0.55 0.72 3.75 496 179 14 73
MCP 66.67 0.58 1.14 2.69 1.25 0.46 0.59 6.27 486 133 14 49.5
DCP 8.33 0.54 1.22 3.84 2.28 0.69 0.69 3.70 602 304 17 89
DCP 16.67 0.59 1.48 4.18 2.57 0.48 0.66 4.75 459 214 13 76
DCP 33.33 0.37 0.77 3.30 1.20 0.58 0.40 2.69 491 202.5 14 82
DCP 66.67 0.57 1.20 3.82 1.15 0.46 0.68 5.36 315 95.5 16 79
DCP 133.33 0.45 0.77 2.61 0.81 0.48 0.54 3.27 357 72 11 67
RP 20.83 0.65 1.50 3.83 2.49 0.75 0.53 4.86 392 241.5 9 60
RP 41.67 0.58 1.40 3.96 2.34 0.47 0.60 4.75 487 259 17 87
RP 83.33 0.61 1.08 3.42 1.51 0.54 0.52 4.32 483 203 12 93
RP 166.67 0.83 1.48 4.05 2.13 0.40 0.68 6.10 417 110 11 49
RP 333.33 0.77 0.84 3.41 0.84 0.37 0.60 5.86 392 99 15 75
Slag 12.50 0.39 0.86 2.03 1.68 0.47 0.38 2.55 310 372 12 38
Slag 25 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0 0 0 0
Slag 50 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0 0 0 0
Slag 100 0.18 0.37 0.88 0.71 0.18 0.21 0.96 136 142 4 10
Slag 200 0.58 1.01 3.36 1.77 0.70 0.38 3.30 415 315 5 45
WA 10.42 0.69 1.03 3.89 1.74 0.56 0.47 3.72 449 288 6 76
WA 20.83 0.74 1.61 4.53 2.93 0.86 0.77 4.99 631 629.5 16 105.5
WA 41.67 0.27 0.45 1.56 0.79 0.38 0.23 1.50 252 99 7 50
WA 83.33 0.55 1.15 3.57 1.95 0.71 0.47 3.89 539 448 15 83
WA 166.67 0.27 0.61 1.80 0.90 0.37 0.28 1.55 185 155 5 35
CLA 33.33 0.60 1.45 3.78 2.44 0.65 0.54 4.55 480 392 15 90
CLA 66.67 0.55 1.05 3.67 1.90 0.71 0.63 3.37 540 289 13 96
CLA 133.33 0.55 1.21 3.51 2.03 0.66 0.63 3.89 469 221 19 105
CLA 266.67 0.66 1.56 4.32 2.81 0.52 0.68 3.90 602 309 16 90
CLA 533.33 0.83 1.72 4.54 2.50 0.51 0.41 4.53 425 152 14 78
CLAT 18.75 0.39 0.54 2.19 0.84 0.41 0.26 1.78 285 145 5 40
CLAT 37.50 0.75 2.31 5.30 4.00 1.15 0.81 6.18 882 848 30 134
CLAT 75 0.14 0.34 1.81 0.60 0.34 0.29 1.00 225 128 8 54
CLAT 150 0.87 1.73 3.99 2.67 0.53 0.43 5.61 532 204 9.5 47.5
CLAT 300 0.54 0.83 1.66 1.53 0.37 0.42 2.18 230 170 10 30
68
A. The Highest Rates of P Application
B. The Lowest Rates of P Application
Appendix 4.2.1 The growth of ryegrass before the first harvest for the highest (a) and lowest (b) rates of all the fertilizers, including zero rate of application (control).
69
A. The Highest Rates of P Application
B. The Lowest Rates of P Application
Appendix 4.2.2 The growth of ryegrass before the second harvest for the highest (a) and lowest (b) rates of all the fertilizers, including zero rate of application (control).
70
A. The Highest Rates of P Application
B. The Lowest Rates of P Application
Appendix 4.2.3 The growth of ryegrass before the third harvest for the highest (a) and lowest (b) rates of all the fertilizers, including zero rate of application (control).
71
Appendix 4.3 Concentration of Phosphorus in Plants Tissue
P Concentration (%) Rate of P Applied mg/kg I Harvest II Harvest III Harvest IV Harvest
0 0.051 0.086 0.066 0.035 MCP 4.17 0.054 0.076 0.06 0.066 MCP 8.33 0.059 0.075 0.055 0.058 MCP 16.67 0.062 0.071 0.061 0.066 MCP 33.33 0.066 0.07 0.059 0.061 MCP 66.67 0.078 0.057 0.065 0.048 DCP 8.33 0.062 0.085 0.062 0.06 DCP 16.67 0.0585 0.085 0.084 0.068 DCP 33.33 0.0645 0.073 0.062 0.055 DCP 66.67 0.073 0.059 0.054 0.061 DCP 133.33 0.071 0.06 0.078 0.063 RP 20.83 0.05 0.086 0.068 0.064 RP 41.67 0.066 0.084 0.07 0.07 RP 83.33 0.068 0.071 0.067 0.068 RP 166.67 0.0665 0.065 0.075 0.063 RP 333.33 0.079 0.062 0.069 0.063 Slag 12.50 0.058 0.088 0.08 0.034 Slag 25 0.056 0.078 0.08 0 Slag 50 0.054 0.076 0.13 0 Slag 100 0.063 0.078 0.08 0.012 Slag 200 0.058 0.084 0.082 0.085 WA 10.42 0.065 0.09 0.08 0.077 WA 20.83 0.08 0.086 0.1 0.088 WA 41.67 0.058 0.083 0.056 0.028 WA 83.33 0.056 0.077 0.08 0.058 WA 166.67 0.065 0.084 0.067 0.04 CLA 33.33 0.056 0.084 0.06 0.061 CLA 66.67 0.052 0.081 0.15 0.066 CLA 133.33 0.056 0.0625 0.085 0.06 CLA 266.67 0.063 0.078 0.073 0.05 CLA 533.33 0.074 0.074 0.062 0.059 CLAT 18.75 0.065 0.088 0.11 0.045 CLAT 37.50 0.067 0.082 0.082 0.084 CLAT 75 0.054 0.094 0.094 0.034 CLAT 150 0.075 0.103 0.08 0.07 CLAT 300 0.064 0.089 0.079 0.05
72
Appendix 4.4.1 RE Values Based on P Applied and Yield for Each Harvest Harvest Fertilizer Equation RE (%) I MCP Y=0.033X+0.02 (R2= 0.96) 100 DCP Y=0.017X+0.10 (R2= 0.97) 57 RP Y=0.0057X+0.12 (R2= 0.97) 24 Slag Y=0.00033X+0.13 (R2= 0.71) 8 WA Y=0.00021X+0.09(R2= 0.12) 6 CMA Y=0.0014X+0.16 (R2= 0.98) 13 CMAT Y=0.0012X+0.06 (R2= 0.89) 7 II MCP Y=0.029X+0.22 (R2= 0.99) 100 DCP Y=0.018X+0.33 (R2= 0.83) 72 RP Y=0.0067X+0.23 (R2= 0.98) 34 Slag Y=0.00043X+0.12 (R2= 0.66) 9 WA Y=0.00081X+0.11 (R2= 0.66) 9 CMA Y=0.0018X+0.17 (R2= 0.99) 16 CMAT Y=0.0016X+0.12 (R2= 0.97) 12 III MCP Y=0.017X+0.57 (R2= 0.71) 100 DCP Y=0.011X+0.52 (R2= 0.82) 74 RP Y=0.0056X+0.72 (R2= 0.75) 70 Slag Y=0.0011X+0.18 (R2= 0.43) 16 WA Y=-0.00024X+0.27 (R2= 0.01) 18 CMA Y=0.0018X+0.38 (R2= 0.83) 33 CMAT Y=0.00062X+0.22 (R2= 0.33) 17 IV MCP Y=0.019X+0.55 (R2= 0.76) 100 DCP Y=0.019X+0.45 (R2= 0.94) 94 RP Y=0.0063X+0.53 (R2= 0.88) 56 Slag Y=0.0013X+0.08 (R2= 0.36) 10 WA Y=-0.00041X+0.35 (R2= 0.01) 22 CMA Y=0.0014X+0.52 (R2= 0.47) 39 CMAT Y=-0.00006X+0.27 (R2= 0.001) 18
73
Appendix 4.4.2 RE Values Based on P Content and P Applied for Each Harvest Harvest Fertilizer Equation RE (%) I MCP Y=0.027X-0.053 (R2= 0.95) 100 DCP Y=0.012X+0.046 (R2= 0.97) 52 RP Y=0.0045X+0.030 (R2= 0.99) 20 Slag Y=0.00021X+0.069 (R2= 0.74) 6 WA Y=0.00022X+0.054 (R2= 0.27) 5 CMA Y=0.00083X+0.069 (R2= 0.99) 9 CMAT Y=0.00082X+0.035 (R2= 0.91) 6 II MCP Y=0.016X+0.22 (R2= 0.96) 100 DCP Y=0.0097X+0.29 (R2= 0.84) 77 RP Y=0.0043X+0.22 (R2= 0.97) 42 Slag Y=0.00032X+0.11 (R2= 0.53) 12 WA Y=0.00064X+0.096 (R2= 0.61) 12 CMA Y=0.0013X+0.13 (R2= 0.99) 20 CMAT Y=0.0015X+0.10 (R2= 0.97) 18 III MCP Y=0.012X+0.32 (R2= 0.79) 100 DCP Y=0.0083X+0.31 (R2= 0.91) 80 RP Y=0.0041X+0.49 (R2= 0.74) 78 Slag Y=0.00092X+0.16 (R2= 0.43) 23 WA Y=-0.00033X+0.19 (R2= 0.01) 24 CMA Y=0.00091X+0.38 (R2= 0.47) 48 CMAT Y=0.00043X+0.19 (R2= 0.18) 24 IV MCP Y=0.0081X+0.39 (R2= 0.51) 100 DCP Y=0.012X+0.26 (R2= 0.95) 107 RP Y=0.0039X+0.38 (R2= 0.84) 72 Slag Y=0.0012X+0.036 (R2= 0.39) 12 WA Y=-0.00043X+0.24 (R2= 0.03) 33 CMA Y=0.00072X+0.32 (R2= 0.37) 45 CMAT Y=-0.00006X+0.21 (R2= 0.003) 26
74
Appendix 4.4.3 RE Values Based on Soil Bic P and P Applied for Each Harvest Fertilizer Equation RE (%) MCP Y=0.10X+2.81 (R2= 0.84) 100 DCP Y=0.028X+3.27 (R2= 0.64) 59 RP Y=0.029X+1.72 (R2= 0.98) 40 Slag Y=0.0093X+1.02 (R2= 0.72) 19 WA Y=0.010X+1.78 (R2= 0.84) 29 CMA Y=0.0091X+2.59 (R2= 0.88) 39 CMAT Y=0.015X+2.75 (R2= 0.82) 45
75