AXM International Space Station 1:100 scalecombo kit #2
Contents:
HARMONY Node 2
KIBO Lab and Robotic Arm
S0 Connectors (extra parts for S1 and P1 trusses)
External Stowage Platform -2
PMA-3 and PMA-2 covers
ORU Crane
STRELA Arms
ISS Antennas
Payloads from HTV-1, HTV-2 and HTV-3
RRM, SGANT, EOTP, SFA
Grapple Bars, UTA, MBSU, STP-H4
©2013
©2012 Not for commercial use
cut cut cut cut
Glue Power & DataGrapple Fixture
“HARMONY” Node 2Print on Cardstock (110 lbs)
1:100 Scale
1 cm
1 inch
Glue petals oneach port
Glue trunnionpin covers
Connect with PMA-2
©2012 Not for commercial use
glue
JAPAN
JAPA
N
cutcut
“Kibo” Lab
cut glue
fron
t
Glue trunnionpin covers
fron
t
L R
Print on Cardstock (110 lbs)
1:100 Scale
1 cm
1 inch
Aftreinforcer
©2012 Not for commercial use
“Kibo” Remote Manipulator System
Use cotton swab with these dimensions ( 2mm in diameter)
1
2
3
Joint Rings
Stoppers
Top cylinder
Cylinders for joint between part 2 and part 3 of main arm
8 mm
8 mm (joint between parts 1 and 2)
38 mm 20 mm
Top cylinder
4 mm
Side (top)
Cylinder that holds Arm part 3
5 mm
9 mm Last joint
End Effector
Optional: You can make thearms with cottonswabs too.
Cover with paper until reaching a width of 4 mm in diameter for 1:100 scale.
Print on Cardstock (90 lbs)
1:100 Scale
1 cm
1 inch
©2013 Not for commercial use
S0 connectors
Shared parts for S1 and P1 trusses
Sheet 2
Print on Cardstock (90 lbs)
1:100 Scale
1 cm
1 inch
Optional parts
These folded radiatorsare not to be glued to the S1 or P1 trusses.These are optional parts in case there is a repair in the real ISS and anyof the radiators need to be stowed.
( including the S0 Connectors)
©2012 Not for commercial use
External Stowage Platform-2
3
6
a
Front
5
cutcut
2
4
7
8
Forward
Forward
Top
Bottom
ESPAD
cutcut
Diagram
Glu
e
Glu
e
Print on Cardstock (90 lbs)
1:100 Scale
1 cm
1 inch
DCSUDCSU
DCSU’s are placed onplates 2 and 3 of ESP-2
Yaw Joint is placedon plate 5 of ESP-2
8
Utility TransferAssembly (UTA)
4 MBSUFlex Hose RotaryCoupler
7
Glue
Glue
6
MBSU
Configuration post STS-135
Print on Cardstock (110 lbs)
©2012 Not for commercial use
PMA-3
PMA-3 and Cover
SASA2nd antenna fromSTS-98 (spare parton Z1)
1:100 Scale
1 cm
1 inch
cut
Step 1Step 2
Cover for PMA-2
Cover for PMA-3
©2012 Not for commercial use
Print on Cardstock (90 lbs)
1:100 Scale
1 cm
1 inch ORU CRANE
ORU Crane location on PMA-1
UNITY
ZARYA
©2012 Not for commercial use
Print on Cardstock (90 lbs)
1:100 Scale
1 cm
1 inchSTRELA ARMS
©2012 Not for commercial use
ISS Antennaes
1:100 Scale
1 cm
1 inch
Print on Cardstock (90 lbs)
UHF Antenna for P1 trussSASA S1 truss SASA P1 truss
FPMUP1 truss
WETAP1 truss
ETVCGP1 truss
ETVCGS1 truss
ETVCGDestiny
WETAS3 truss
WETAUnity
External lightsS1 truss
External lightsUnity
ETVCGP1 truss
UHF Antenna for Destiny
Print on Cardstock (90 lbs)
©2013 Not for commercial use
1 cm
1 inch
1:100 Scale
Payloads from HTV-1, HTV-2 and HTV-3
CTC-4
1
CTC-4
Flex Hose Rotary Coupler (FHRC)
Glue
5
Glue
SCAN Testbed
FRAMACTIVATION
DRIVELOCK
A B
(HTV-2)
To ELC-4
Roll into a tubeand insert into JEM-EF
MCE
(HTV-3)
To ELC-3
To JEM -EF
Roll into a tubeand insert into JEM-EF
HREP
Roll into a tubeand insert into JEM-EF
SMILES
(HTV-1)
To JEM -EF
To JEM -EF
Print on Cardstock (90 lbs)
©2013 Not for commercial use
1 cm
1 inch
1:100 Scale
(STS-132)
SGANT Antenna
ROBOTIC REFUELING MISSION (RRM)
The RRM will be permanently attached to ELC-4 on plate 3
(STS-135)
RRM, SGANT, EOTP and SFA
On top of Z1 next to first SGANT antenna
ORU Temporary Platformis glued on top of S0 truss
Front
SIDE 2
SIDE 3
CO
MM
ON
H2
BATTERY
SIDE 1
CO
MM
ON
H2
EOTP
H2
BATTERY
H2
cut outgray areas
SFA (Small Fine Arm)
Print on Cardstock (90 lbs)
©2013 Not for commercial use
1 cm
1 inch
1:100 Scale
Grapple Bars, UTA, MBSU, STP-H4
Heat Rejection Subsystem Grapple Fixtures
Grapple Bar 1 Grapple Bar 2(To be placed on S1 truss) (To be placed on P1 truss)
FRA
MA
CTIVATIO
ND
RIV
ELO
CK
Utility TransferAssembly (UTA)
MBSU
FRA
MA
CTI
VATI
ON
DR
IVE
LOC
K
STP-H4
UTA
ORU UTA ORU
UTA
ORU
FRA
MA
CTIVATIO
ND
RIV
ELO
CK
STP-H
4
UTA ORU
Diagram
Diagram
X
X
Diagram
HTV-4 HTV-4
HTV-4
Dragon CRS-2
8
Use PAPER only
Use this part to patchthe space where STP-H3was glued (ELC-3)