Download - Balanza Spider
-
8/15/2019 Balanza Spider
1/332
IndustrialQuick ReferenceGuide
15311300A
(5/98).01
-
8/15/2019 Balanza Spider
2/332
© Mettler-Toledo, Inc. 1998
No part of this manual may be reproduced or transmitted in any form or by any means,
electronic or mechanical, including photocopying and recording, for any purpose without theexpress written permission of Mettler-Toledo, Inc.
U.S. Government Restricted Rights: This documentation is furnished with Restricted Rights.
-
8/15/2019 Balanza Spider
3/332
METTLER TOLEDO
Publication Revision HistoryAn overview of this manual’s revision history is compiled below.
Publication Name: Industrial Quick Reference User’s Guide
Publication Part Number: 15311300A Publication Date: 10/98
Part Number Date Revisions
15311300A 5/98 Added Chapter 39, Cougar Indicator
-
8/15/2019 Balanza Spider
4/332
-
8/15/2019 Balanza Spider
5/332
INTRODUCTION
Information regarding METTLER TOLEDO Technical Training may be obtained by writing, calling,or faxing to:
METTLER TOLEDO350 W. Wilson Bridge RoadWorthington, Ohio 43085
ph: (614) 438-4400fax: (614) 438-4444
WARNING
This publication is provided solely as a guide for individuals who have received technical training andis familiar with the technical manuals of the Mettler Toledo products.
This guide is not meant to replace the technical manual for various products.
Please review the specific technical manuals for detailed instructions and safety precautions beforeoperating or servicing the various Mettler Toledo products.
METTLER TOLEDO RESERVES THE RIGHT TO MAKE REFINEMENTS ORCHANGES WITHOUT NOTICE.
-
8/15/2019 Balanza Spider
6/332
PRECAUTIONS
WARNINGONLY PERMIT QUALIFIED PERSONNEL TO SERVICE
THIS EQUIPMENT. EXERCISE CARE WHEN MAKINGCHECKS, TESTS AND ADJUSTMENTS THAT MUST BEMADE WITH POWER ON. FAILING TO OBSERVETHESE PRECAUTIONS CAN RESULT IN BODILY HARM.
WARNINGFOR CONTINUED PROTECTION AGAINST SHOCKHAZARD CONNECT TO PROPERLY GROUNDEDOUTLET ONLY.
DO NOT REMOVE THE GROUND PRONG.
WARNINGDISCONNECT ALL POWER TO THIS UNIT BEFOREREMOVING THE FUSE OR SERVICING.
CAUTIONBEFORE CONNECTING/DISCONNECTING ANY INTERNAL ELECTRONICCOMPONENTS OR INTERCONNECTING WIRING BETWEEN ELECTRONICEQUIPMENT ALWAYS REMOVE POWER AND WAIT AT LEAST THIRTY (30)SECONDS BEFORE ANY CONNECTIONS OR DISCONNECTIONS ARE MADE.FAILURE TO OBSERVE THESE PRECAUTIONS COULD RESULT IN DAMAGE TOOR DESTRUCTION OF THE EQUIPMENT OR BODILY HARM.
CAUTIONOBSERVE PRECAUTIONS
FOR HANDLINGELECTROSTATIC
SENSITIVE DEVICES.
READ this manual BEFORE
operating or servicing thisequipment.
FOLLOW these instructions
carefully.
SAVE this manual for futurereference.
DO NOT allow untrainedpersonnel to operate, clean,inspect, maintain, service,or tamper with this
equipment.
ALWAYS DISCONNECT thisequipment from the power
source before cleaning orperforming maintenance.
CALL METTLER TOLEDO for
parts, information, andservice.
-
8/15/2019 Balanza Spider
7/332
METTLER TOLEDO
Publication Problem ReportIf you find a problem with our documentation, please complete and fax this form to (614) 438-4783
Publication Name: Industrial Quick Reference User’s Guide
Publication Part Number: 15311300A Publication Date: 5/98
PROBLEM(S) TYPE: DESCRIBE PROBLEM(S):
Technical Accuracy Text Illustration
Completeness Procedure/step Illustration Definition What information is Example Guideline Feature
missing?
Explanation
Other (please explain below)
ClarityWhat is not clear?
SequenceWhat is not in the right
order?
Other CommentsUse another sheet for
additional comments.
Your Name: Location:
Phone Number: ( )
Mettler-Toledo, Inc. Printed in U.S.A. A14981600A
Fax this completed form to MarCom at (614) 438-4783
-
8/15/2019 Balanza Spider
8/332
-
8/15/2019 Balanza Spider
9/332
METTLER TOLEDOScales & Systems350 West Wilson Bridge RoadWorthington, Ohio 43085-2273
P/N: 15311300A
(5/98).01
METTLER TOLEDO® is a registered trademark of Mettler-Toledo, Inc.©1998 Mettler-Toledo, Inc.
Printed in U.S.A.
15311300A
-
8/15/2019 Balanza Spider
10/332
CONTENTS
1 3026/3036 Over/Under Scales ............................................................................... 1-1
Jumpers and Keyboard Functions ......................................................................................... 1-1Display PCB........................................................................................................................1-1
Power Supply PCB ............................................................................................................... 1-1Keyboard ............................................................................................................................1-1
Softswitch Settings .............................................................................................................. 1-2
Error Codes......................................................................................................................... 1-3
2 3027 Over/Under................................................................................................. 2-1Jumpers and Keyboard Functions ......................................................................................... 2-1
Display PCB........................................................................................................................2-1
Power Supply PCB ............................................................................................................... 2-1
Keyboard ............................................................................................................................2-1Softswitch Settings .............................................................................................................. 2-2
Error Codes......................................................................................................................... 2-3
3 8140 Digital Indicator .......................................................................................... 3-1Jumpers and Keyb[oard Functions ........................................................................................ 3-1
Softswitch Settings .............................................................................................................. 3-2
Error Codes......................................................................................................................... 3-3
4 M8141 Power Supply........................................................................................... 4-1
Jumpers and Keyboard Functions ......................................................................................... 4-1Jumpers .............................................................................................................................4-1Keyboard ............................................................................................................................4-1
Setup Chart ........................................................................................................................ 4-2
Error Codes......................................................................................................................... 4-3
5 8142 Indicator .................................................................................................... 5-1Jumpers and Keyboard Functions ......................................................................................... 5-1
Main PCB Jumpers .............................................................................................................. 5-1Dual Display PCB Jumpers ...................................................................................................5-1Rack Display PCB Jumpers...................................................................................................5-1
Optional BCD/Analog PCB.....................................................................................................5-1Keyboard Functions During Setup...........................................................................................5-2
Quick Reference Chart ......................................................................................................... 5-2
Error Codes......................................................................................................................... 5-5Operational Error Codes ........................................................................................................ 5-5
Calibration Error Codes .........................................................................................................5-6
-
8/15/2019 Balanza Spider
11/332
6 8213 Checkstand Scale ....................................................................................... 6-1Jumpers Functions ..............................................................................................................6-1
Main PCB Jumpers .............................................................................................................. 6-1
Softswitch Settings .............................................................................................................. 6-1
Calibration.......................................................................................................................... 6-2
Required Test Weights ..........................................................................................................6-2Error Codes......................................................................................................................... 6-3
7 8505 Printer ....................................................................................................... 7-1Keyboard Functions ............................................................................................................. 7-1
Accessing the Setup Mode ................................................................................................... 7-1
Pushbutton Functions During Setup....................................................................................... 7-1
Setup Quick Reference Chart ................................................................................................ 7-2
Error Codes......................................................................................................................... 7-4
8 8510 Panel Mount Indicator ................................................................................. 8-1Jumpers and Keyboard Functions ......................................................................................... 8-1Main PCB Jumpers .............................................................................................................. 8-1Power Supply PCB ............................................................................................................... 8-1Dual Display PCB Jumpers ...................................................................................................8-1
Keyboard ............................................................................................................................8-1
Softswitch Settings .............................................................................................................. 8-2
Error Codes......................................................................................................................... 8-4
9 8510 Stainless Steel Indicator .............................................................................. 9-1Jumpers and Keyboard Functions ......................................................................................... 9-1
Display PCB Jumpers........................................................................................................... 9-1Power Supply PCB ............................................................................................................... 9-1
Keyboard ............................................................................................................................9-1
Softswitch Settings .............................................................................................................. 9-2
Error Codes......................................................................................................................... 9-4
10 8510 Wall Mount Indicator ............................................................................... 10-1Jumpers and Keyboard Functions ....................................................................................... 10-1
Display PCB Jumpers......................................................................................................... 10-1
Power Supply PCB ............................................................................................................. 10-1Keyboard ..........................................................................................................................10-1
Softswitch Settings............................................................................................................ 10-2Error Codes....................................................................................................................... 10-4
-
8/15/2019 Balanza Spider
12/332
11 8511 Digital Indicator ...................................................................................... 11-1Jumpers and Keyboard Functions ....................................................................................... 11-1
Main PCB Jumpers ............................................................................................................ 11-1Power Supply PCB ............................................................................................................. 11-1
Keyboard ..........................................................................................................................11-2
Soft Switch Settings ............................................................................................................11-3Error Codes....................................................................................................................... 11-5
12 8520 Digital Indicator ...................................................................................... 12-1Jumpers and Keyboard Functions ....................................................................................... 12-1
Main PCB Jumpers ............................................................................................................ 12-1
Programming Procedure ..................................................................................................... 12-1Keyboard Functions............................................................................................................12-2
Softswitch Settings............................................................................................................ 12-2Exiting The Setup Routine..................................................................................................12-13
Error Codes..................................................................................................................... 12-14
13 8522 Digital Indicator ...................................................................................... 13-1Jumpers and Keyboard Functions ....................................................................................... 13-1
Main PCB Jumpers ............................................................................................................ 13-1Passive Active Analog PCB..................................................................................................13-1Keyboard ..........................................................................................................................13-1
Softswitch Settings............................................................................................................ 13-2
Error Codes....................................................................................................................... 13-5
14 8525 Digital Indicator ...................................................................................... 14-1Jumpers and Keyboard Functions ....................................................................................... 14-1
Main PCB Jumpers ............................................................................................................ 14-1Fiber Optic PCB .................................................................................................................14-1
Softswitch Settings............................................................................................................ 14-2
Error Codes....................................................................................................................... 14-5
15 8530 DigiTOL®
Indicator ................................................................................... 15-1Jumpers and Keyboard Functions ....................................................................................... 15-1
Main PCB Jumpers ............................................................................................................ 15-1Keyboard ..........................................................................................................................15-1
Softswitch Settings............................................................................................................ 15-2
Error Codes....................................................................................................................... 15-6
16 8530VS DigiTOL®
Indicator ............................................................................... 16-1Jumpers and Keyboard Functions ....................................................................................... 16-1
Main PCB Jumpers ............................................................................................................ 16-1Keyboard ..........................................................................................................................16-1
Softswitch Settings............................................................................................................ 16-2
Error Codes....................................................................................................................... 16-6
-
8/15/2019 Balanza Spider
13/332
17 8571 High Resolution Counting Scale................................................................ 17-1Jumpers and Keyboard Functions ....................................................................................... 17-1
Main PCB Jumpers ............................................................................................................ 17-1Keyboard ..........................................................................................................................17-1
Softswitch Settings............................................................................................................ 17-2
Error Codes....................................................................................................................... 17-3
18 8572 Counting Scale ....................................................................................... 18-1Keyboard Functions ........................................................................................................... 18-1
Softswitch Settings............................................................................................................ 18-2
Error Codes....................................................................................................................... 18-5
19 8581 Counting Scale ....................................................................................... 19-1Jumpers and Keyboard Functions ....................................................................................... 19-1
Main PCB Jumpers ............................................................................................................ 19-1
Display PCB......................................................................................................................19-1Keyboard ..........................................................................................................................19-1
Softswitch Settings............................................................................................................ 19-2
Error Codes....................................................................................................................... 19-4
20 8582 High Resolution Counting Scale................................................................ 20-1Jumpers and Keyboard Functions ....................................................................................... 20-1
Main PCB Jumpers ............................................................................................................ 20-1
Analog Scale PCB .............................................................................................................. 20-1Digital Scale PCB...............................................................................................................20-1
Softswitch Settings............................................................................................................ 20-2
Error Codes....................................................................................................................... 20-4
21 8617 Scoreboard............................................................................................. 21-1Jumpers and Switch Settings.............................................................................................. 21-1
Main PCB Jumpers ............................................................................................................ 21-1Hardswitch Descriptions ..................................................................................................... 21-2
Select Scoreboard Operation Switch S3......................................................................21-2Scoreboard Operation Selection ................................................................................21-2
Scoreboard Setup Switch S4 ....................................................................................21-2Multidrop Address Selection .....................................................................................21-2
Softswitch Settings............................................................................................................ 21-3Simple ASCII Mode............................................................................................................. 21-4
MULTI-SCALE MODE........................................................................................................... 21-4[F1 2]............................................................................................................................ 21-4
Error Codes....................................................................................................................... 21-5
-
8/15/2019 Balanza Spider
14/332
22 8623 Scoreboard............................................................................................. 22-1Jumpers........................................................................................................................... 22-1
Displayed Data (Weight) Configuration Jumper Connections....................................................22-1Input Control Wiring ...........................................................................................................22-1
Data I/O Wiring..................................................................................................................22-2
Dip Switches..................................................................................................................... 22-2Error Codes....................................................................................................................... 22-3
23 8624 Scoreboard............................................................................................. 23-1Jumpers........................................................................................................................... 23-1
Displayed Data Jumpers ..................................................................................................... 23-1
Input Control Jumpers ........................................................................................................ 23-2
Switch Settings ................................................................................................................. 23-3
Error Codes....................................................................................................................... 23-3
24 8682 Scale ..................................................................................................... 24-1Keyboard Functions ........................................................................................................... 24-1
Softswitch Settings............................................................................................................ 24-2
Error Codes....................................................................................................................... 24-3
25 8806 Printer ................................................................................................... 25-1Jumpers and Keyboard Functions ....................................................................................... 25-1
Jumpers - All Versions........................................................................................................ 25-1
Keyboard ..........................................................................................................................25-1
Switch Settings ................................................................................................................. 25-2
Dip Switches..................................................................................................................... 25-2
Error Codes....................................................................................................................... 25-4
26 8807 Printer ................................................................................................... 26-1Keyboard Functions ........................................................................................................... 26-1
LED Displays..................................................................................................................... 26-1
Self Test Mode ...................................................................................................................26-1
Switch Settings ................................................................................................................. 26-2
Error Codes....................................................................................................................... 26-2
27 8844 Printer ................................................................................................... 27-1Jumpers ...........................................................................................................................27-1
Dip Switches..................................................................................................................... 27-1Baud Rate Selections.......................................................................................................... 27-2Switch Bank 2 Settings ....................................................................................................... 27-2
Troubleshooting ................................................................................................................ 27-3
Self Tests ......................................................................................................................... 27-4Test 1............................................................................................................................... 27-4
Test 2 and 3 .....................................................................................................................27-4
-
8/15/2019 Balanza Spider
15/332
28 8845 Printer ................................................................................................... 28-1Dip Switches..................................................................................................................... 28-1
Baud Rate Selections.......................................................................................................... 28-1Switch Bank 2 Settings ....................................................................................................... 28-2
29 8856 Strip Printer ............................................................................................ 29-1Keyboard Functions ........................................................................................................... 29-1
Self Test Mode .................................................................................................................. 29-1
Hex Dump Mode ............................................................................................................... 29-1
Programming Switches ...................................................................................................... 29-2
International Character Set Selection:.................................................................................. 29-2
(shaded areas represent default settings) .............................................................................. 29-2Communication Parameters ............................................................................................... 29-3
Word Length (Data Bits) ..................................................................................................... 29-3
Parity Bit Selection .............................................................................................................29-3Baud Rate Selection ...........................................................................................................29-3
Error Codes....................................................................................................................... 29-4
30 8860 Printer ................................................................................................... 30-1Dip Switches..................................................................................................................... 30-1
Logic PCB Jumper Selections ..............................................................................................30-1
[SW1-1]:Data Input Mode Select.............................................................................. 30-2[SW1-6], [SW1-7], [SW1-8]:Label Format (Mode II Operation Only)...........................30-2[SW2-1]: Character Output Enable (Mode I) or Expanded Print Size (Mode II)........ 30-2
[SW2-1]: Character Enable (Mode I Operation [SW1-1 On]) ...............................30-3[SW2-1]:Expanded Print Size (Mode I Operation [SW1-1 Off]......................................30-3[SW2-2], [SW2-3] and [SW2-4]Preferred Line Selection ............................................ 30-3
[SW2-5], [SW2-6]:Bar Code Format........................................................................ 30-3[SW2-7]:Checksum Enable[SW2-8]:Baud Rate Select ................................................ 30-3
Self Test ........................................................................................................................... 30-4Bar Code Test Label ........................................................................................................... 30-4Logic PCB Switch Settings Test ............................................................................................30-4
Error Codes....................................................................................................................... 30-4
31 8861 Printer ................................................................................................... 31-1Softswitch Settings............................................................................................................ 31-1
Error Codes....................................................................................................................... 31-8
32 BC/SC Counting Scales...................................................................................... 32-1Loading Master Mode Defaults ........................................................................................... 32-1
Keyboard Functions for Master Mode................................................................................... 32-1
-
8/15/2019 Balanza Spider
16/332
33 Jaguar............................................................................................................ 33-1Keyboard Functions ........................................................................................................... 33-1
Jumpers and Switch Settings Controller............................................................................... 33-2 Analog .............................................................................................................................33-3
Allen-Bradley PCB..............................................................................................................33-3
POWERCELL I/O PCB.......................................................................................................... 33-3MMR (IDNET) I/F PCB......................................................................................................... 33-3Multifunction I/O PCB..........................................................................................................33-4
Scale Interface Program Block............................................................................................ 33-4Market Sub-block...............................................................................................................33-4Scale Type Sub-block ......................................................................................................... 33-4Calibration Unit Sub-block ................................................................................................... 33-6
Capacity Sub-block ............................................................................................................ 33-7Increment Size Sub-block.................................................................................................... 33-7Shift Adjustment Sub-block.................................................................................................. 33-8Linearity Correction Sub-block.............................................................................................33-8
Calibration Sub-block ......................................................................................................... 33-9Without Linearity Correction .....................................................................................33-9With Linearity Correction Enabled..............................................................................33-9
Zero Adjustment Sub-block ................................................................................................ 33-10Span Adjustment Sub-block............................................................................................... 33-10Gravity Adjustment Sub-block...............................................................................................33-10Reset to Factory Sub-Block................................................................................................ 33-11
Service Mode for .............................................................................................................. 33-11MMR (IDNET) Bases ........................................................................................................ 33-11RESET program Sub-block ................................................................................................33-12
SCALE PARAMETERS program Sub-block............................................................................. 33-12LINEARITY program Sub-block ..........................................................................................33-13
CALIBRATION program Sub-block.......................................................................................33-13SAVE PARAMETERS program Sub-block ..............................................................................33-14
RETURN program Sub-block................................................................................................ 33-14
Application Environment Program Block............................................................................. 33-14Character Set Sub-block.................................................................................................... 33-14Language Sub-block ........................................................................................................ 33-15
Keyboard Type Sub-block ................................................................................................. 33-15Scale ID Sub-block........................................................................................................... 33-15Time and Date Sub-block..................................................................................................33-16
Alternate Weight Units Sub-block........................................................................................33-17
Power Up Operation Sub-block .........................................................................................33-19Tare Operation Sub-block..................................................................................................33-19Zero Operation Sub-block..................................................................................................33-21Zero Operation Sub-block for MMR (IDNET) Bases................................................................33-22
Stability Detect Sub-block ..................................................................................................33-23Stability Detect Sub-block for MMR (IDNET) Bases................................................................33-23Beeper Operation Sub-block ................................................................................................ 33-24
Application Type Sub-block ...............................................................................................33-24 Vibration Rejection Sub-block ............................................................................................ 33-25 Vibration Rejection Sub-block for MMR (IDNET) Bases ..........................................................33-26
Serial Interface Program Block.......................................................................................... 33-27
-
8/15/2019 Balanza Spider
17/332
Configure Port Sub-block ..................................................................................................33-27Local .................................................................................................................. 33-28Remote ............................................................................................................... 33-29
Add a Connection ................................................................................................. 33-29
Delete a Connection.............................................................................................. 33-33Configure Template Sub-block .......................................................................................... 33-33
Clear Template ..................................................................................................... 33-34Copy Template ..................................................................................................... 33-34
Edit Template ....................................................................................................... 33-34
Configure Discrete Program Block..................................................................................... 33-37Discrete Inputs Sub-block.................................................................................................. 33-38Discrete Outputs Sub-block................................................................................................33-39
Assign Setpoints Sub-block ................................................................................................ 33-41Configure Memory Program Block ......................................................................................33-41Configure Literals Sub-block ................................................................................................ 33-42Configure Prompts Sub-block ........................................................................................... 33-42
Configure Consecutive Numbering Sub-block.......................................................................33-44
Configure JagBASIC Program Block .................................................................................. 33-44Password Sub-block ........................................................................................................ 33-44Keyboard Sub-block ......................................................................................................... 33-45
Display Sub-block............................................................................................................ 33-45 Auto Start Sub-block ......................................................................................................... 33-46Manual Start Sub-block..................................................................................................... 33-46
Send RAM Files Sub-block.................................................................................................33-46Initialize RAM Disk Sub-block ........................................................................................... 33-47Password Maintenance Sub-block...................................................................................... 33-47
Configure Network Program Block..................................................................................... 33-48Network Keyboard/ Display Sub-block ................................................................................33-48
PC Data Sub-block........................................................................................................... 33-48PLC SP Control Sub-block ................................................................................................. 33-49Diagnostics and Maintenance Program Block ......................................................................... 33-49
Memory Test Sub-block .................................................................................................... 33-49Display Test Sub-block .....................................................................................................33-50Keyboard Test Sub-block ..................................................................................................33-50Scale Test Sub-block ........................................................................................................ 33-50
MMR (IDNET) Scale Bases .................................................................................... 33-51DigiTOL J-Box or Power Cell Bases.........................................................................33-51
Serial Test Sub-block ........................................................................................................ 33-55
Parallel I/O Test Sub-block ................................................................................................33-57PAR 1 or PAR 3 (Discrete Input).............................................................................33-57
PAR 2 or PAR 4 (Discrete Output)........................................................................... 33-57Network Test Sub-block ....................................................................................................33-58
Send BRAM to Jag Sub-block ...........................................................................................33-58Print Setup Sub-block ....................................................................................................... 33-59Reset to Factory Sub-block ................................................................................................ 33-59
Options Program Block .................................................................................................... 33-60
Error Codes and Actions................................................................................................... 33-61
34 Lynx ............................................................................................................... 34-1
-
8/15/2019 Balanza Spider
18/332
Jumper and Keyboard Functions......................................................................................... 34-1Keyboard Functions............................................................................................................34-1Controller PCB ...................................................................................................................34-2Soft Switch Settings ............................................................................................................34-2
Scale Interface Program Block............................................................................................ 34-3
Market Sub-block...............................................................................................................34-3Scale Type Sub-block ......................................................................................................... 34-3Calibration Unit Sub-block ................................................................................................... 34-4Capacity Sub-block ............................................................................................................ 34-4
Increment Size Sub-block.................................................................................................... 34-5Shift Adjust Sub-block.........................................................................................................34-5Linearity Correction Sub-block.............................................................................................34-6
Calibration Sub-block ......................................................................................................... 34-6Without Linearity Correction .....................................................................................34-6With Linearity Correction Enabled..............................................................................34-7
Zero Adjustment Sub-block .................................................................................................. 34-7
Span Adjustment Sub-block.................................................................................................. 34-8
Gravity Adjustment Sub-block .............................................................................................34-8Character Set Sub-block...................................................................................................... 34-9Time and Date Sub-block....................................................................................................34-9
Weight Units Sub-block..................................................................................................... 34-10Power up Operation Sub-block........................................................................................... 34-11Tare Operation Sub-block..................................................................................................34-11
Zero Operation Sub-block..................................................................................................34-13Stability Detection Sub-block................................................................................................ 34-15
Vibration Rejection Sub-block ............................................................................................ 34-15Port Configure Sub-block ..................................................................................................34-17
Connection .......................................................................................................... 34-19Configure Template Sub-block ...........................................................................................34-22
Clear Template ..................................................................................................... 34-22
Copy Template ..................................................................................................... 34-23Edit Template ....................................................................................................... 34-23
Configure Printer Control Sub-block ....................................................................................34-27Configure Inputs Sub-block................................................................................................34-28
Configure Outputs Sub-block ............................................................................................34-28Configure Literals Sub-block ................................................................................................ 34-30Configure Prompts Sub-block ............................................................................................ 34-30Configure Consecutive Numbering Sub-block.......................................................................34-32
Analog Output Sub-block .................................................................................................. 34-32BCD Output Sub-block ......................................................................................................34-33
Accumulate Sub-block ...................................................................................................... 34-33ID/Tare Sub-block ............................................................................................................ 34-34Password Sub-block ........................................................................................................ 34-36Dynamic Sub-block.......................................................................................................... 34-37Memory Test Sub-block .................................................................................................... 34-37
Display Test Sub-block .....................................................................................................34-37Keyboard Test Sub-block ..................................................................................................34-38Scale Test Sub-block ........................................................................................................ 34-38
Serial I/O Test Sub-block...................................................................................................34-39Discrete I/O Test Sub-block................................................................................................34-40
-
8/15/2019 Balanza Spider
19/332
Discrete Input.......................................................................................................34-40Discrete Output..................................................................................................... 34-41
Print Setup Sub-block ....................................................................................................... 34-41Reset to Factory Sub-block ................................................................................................ 34-42
Error Codes..................................................................................................................... 34-43
35 Panther .......................................................................................................... 35-1Jumpers and Switch Settings.............................................................................................. 35-1
Controller PCB ...................................................................................................................35-1Keyboard Functions............................................................................................................35-2
Program Block Access ....................................................................................................... 35-3
General Programming Procedure ........................................................................................ 35-3
Softswitch Settings............................................................................................................ 35-4
Error Codes....................................................................................................................... 35-8
36 Spider............................................................................................................. 36-1
Single Load Cell Connections ............................................................................................. 36-1Table of Scale Base Parameters ...........................................................................................36-3Servicemode Configuration.................................................................................................. 36-4
Accessing Service Mode......................................................................................................36-4
Navigating in Servicemode .................................................................................................. 36-5Unit Program Block ............................................................................................................ 36-5Ramp Program Block ......................................................................................................... 36-6
Serial Number Program Block.............................................................................................. 36-6Weighing Cell Program Block .............................................................................................. 36-6
Approval Sub-block ............................................................................................................ 36-7Capacity Sub-block ............................................................................................................ 36-7
Range Program Block.........................................................................................................36-8Resolution Program Block................................................................................................... 36-8
Calibration Program Block.................................................................................................. 36-9Geo Sub-block................................................................................................................... 36-9
Geo Mode ............................................................................................................. 36-9Cal Exe Sub-block............................................................................................................ 36-10Factory Reset Program Block ............................................................................................. 36-10List Program Block........................................................................................................... 36-11
Return Program Block....................................................................................................... 36-11Mastermode Configuration................................................................................................. 36-11
Accessing Mastermode ..................................................................................................... 36-12
Mastermode Entry ............................................................................................................ 36-12
Navigating in Mastermode................................................................................................. 36-12Function Program Block.................................................................................................... 36-13
Auto Zero Correction Program Block ................................................................................... 36-14
Auto Tare Program Block .................................................................................................. 36-14 Automatic Shutdown Program Block ...................................................................................36-15Power-Up (Save) Program Block ....................................................................................... 36-15
Vibration Adapter Program Block........................................................................................36-16Process Adapter Program Block .........................................................................................36-16Interface 1 Program Block................................................................................................. 36-17Reset Interface to Factory .................................................................................................. 36-17
-
8/15/2019 Balanza Spider
20/332
Communication ............................................................................................................... 36-18Parameters Sub-block ...................................................................................................... 36-18Operating Mode Sub-block ................................................................................................36-19Data Definition Sub-block.................................................................................................. 36-20
Define Print Format Sub-block............................................................................................ 36-20Exit Interface 1 Sub-block.................................................................................................. 36-21Interface 2 Program Block (Optional)..................................................................................36-21
Accuracy Control Program Block ........................................................................................36-21
List Program Block........................................................................................................... 36-22Restricting Access to Mastermode ......................................................................................36-22
Access to Mastermode with Restricted Entry .........................................................................36-22
Reset to Factory Program Block .........................................................................................36-23Error Codes and Descriptions ............................................................................................36-24
37 TrimWeigh ...................................................................................................... 37-1Jumpers and Keyboard Functions ....................................................................................... 37-1
Display PCB Jumpers......................................................................................................... 37-1
Power Supply PCB Jumpers.................................................................................................. 37-1Keyboard Functions During Setup.........................................................................................37-1
Switch Settings ................................................................................................................. 37-2
Error Codes....................................................................................................................... 37-4
38 XX38 .............................................................................................................. 38-1Softswitch Functions.......................................................................................................... 38-1
Error Codes....................................................................................................................... 38-5
39 Cougar Industrial Terminal................................................................................ 39-1
Jumpers and Keyboard Functions ....................................................................................... 39-1Main PCB Jumpers ............................................................................................................ 39-1Keyboard ..........................................................................................................................39-1
Softswitch Settings for Cougar Standard Software................................................................. 39-2
Softswitch Settings for Cougar VS Software.......................................................................... 39-6
Error Codes..................................................................................................................... 39-10
-
8/15/2019 Balanza Spider
21/332
-
8/15/2019 Balanza Spider
22/332
Chapter 1: 3026/3036 Over/Under ScalesJumpers and Keyboard Functions
(1/98) 1-1
1 3026/3036 Over/Under Scales
Jumpers and Keyboard
Functions
Display PCBW1 - Decimal Point, comma display
Out = decimal pt.; In = comma
W2 - ROM Select
Must short (1-2)
W3 - ROM Enable
Must be in
Power Supply PCBW1 - Setup Entry
In = enable; Out = disable
W2 - Internal Suppresser (Use with TTL outputs)
In = connect suppresser; Out = disconnect
KeyboardKey Setup Function Normal Function
ZERO Back Up to Prev. Step Re-Zero Scale
TARE/TARGET Toggle Selections Enter Target or Tare
CLEAR Advance to [CALOFF] Clear Tare or Target Wgt
UNITS N/A Toggle Units (Lb/Kg)
PRINT Accept Selection Initiate a Print Command
-
8/15/2019 Balanza Spider
23/332
METTLER TOLEDO Industrial Quick Reference User’s Guide
(1/98)1-2
Softswitch Settings
F0-Span Adjust 1-Enable; 0-Disable
F1-Operating Mode0 = NA; = 3026; 2 = NA; 3 = 3036; 4 = NA;
F1.5- Indicator Mode0 = indicator; 1 = over/under
F2-Calibration Units0 = LB; 1 = KG; 2 = lb-oz; 3 = oz; 4 = g;
F3-Units Key 1-Enable; 0-Disable
F4-Weight/LED Enable0 = wgt on, led off; 1 = wgt on, led on;
F4.1-Zone Width Entry
0 = Increments; 1 = % of target;F5-Zero Cursor /%Target
1-Enable; 0-DisableF6-Auto Zero Maint.
0 = disable; 1 = .5inc; 2 = 1inc; 3 = 3 inc.F6.1AZM in Net Mode
0 = gross; 1 = gross and net F7-Zero Key Enable
0 = disable; 1 = 2%; 2 = 20%; 3 =20%GandNet
F8-Motion Sensitivity
0 = 1d; 1 = 3d;
F9-Filter Selection0 = disable; 1 = light; 2 = medium; 3 = heavy
9.1-Dig. Load Cell Filter
1-Enable; 0-DisableF10-Expanded Weight
1-Enable; 0-Disable
F11-Net Wgt. Display0 = gross wgt; 1 = net diff.
F12-Zone ProgrammingPrint = enter; Tar e = skip
12.1-Setup Entry Point 0 = F0; 1 = F12
12.2-High Zone WidthTare = toggle; Print = Select
12.3-High Accept WidthTare = toggle; Print = Select
12.4-Low Accept WidthTare = toggle; Print = Select
12.5-Low Zone WidthTare = toggle; Print = Select
12.6-Stored Tare Wgts.1-Enable; 0-Disable
F13-Tare Enable1-Enable; 0-Disable; 2 = auto tare
F14-Auto Clear Tare
1-Enable; 0-DisableF15-Serial Port Program.
Print = enter; Tare = skip15.1-Format
0 = cont. ;1 = demand15.2-Baud Rate
Tare = toggle; Print = Select 15.3-Parity
0 = always 0; 1 = odd; 2 = even15.4-Checksum
1-Enable; 0-Disable
15.5-Line Format Select 0 = single line displayed; 1 = GTN single line;2 = GTN multiple line;
15.6-Double Wide Print
1-Enable; 0-Disable
15.7-Auto Print 1-Enable; 0-Disable
15.8-Print Wgt. Class1-Enable; 0-Disable
15.9-Stop Bits0 = 1; 1 = 2;
F16-ASCII Input 1-Enable; 0-Disable
F18-Tare Interlocks1-Enable; 0-Disable
F19-Motion Blanking1-Enable; 0-Disable
F20-TTL Input 0 = print; 1 = tare; 2 = zero; 3 = unit selection
CAL-CalibrationPrint = enter; Tare = skip
-
8/15/2019 Balanza Spider
24/332
Chapter 1: 3026/3036 Over/Under ScalesError Codes
(1/98) 1-3
Error Codes
Error Code Description Suggested Corrective Action
E1 Program Memory Fatal 1. Check DC Supply Voltages2. Replace Display PCB
E2 Internal Ram MemoryFatal Error
1. Check DC Supply Voltages2. Replace Display PCB
E3 NOVRAM Memory Error 1. Check DC Supply Voltages2. Reprogram, Recalibrate3. Replace Display PCB
E8 Communication Loss With DLC 1. Check DC Supply Voltages2. Check Interconnect Harnesses for Load Cell and PCB’s3. Replace Load Cell4. Replace Display PCB
E9 DLC Out of Range, Under Capacity 1. Check For Mechanical Bind2. Check DC Supply Voltages3. Replace Load Cell
4. Replace Display PCB
E10 DLC Memory Verify Fatal Error 1. Check DC Supply Voltages
2. Replace Load Cell
E11 DLC ROM Error 1. Check DC Supply Voltages2. Replace Load Cell
E13 DLC EPROM Error 1. Check DC Supply Voltages2. Recalibrate Scale
3. Replace Load Cell
E16 Math Error 1. Press Clear Key To Clear Error, Check Program and Recalibrate
E32 Insufficient Test Used for Calibration 1. Recalibrate With At Least 50% of Programmed Scale CapacityE34 Test Weight Over Cap 1. Check Capacity Programming, Use Test Weight Less Than Capacity
E35 Calibration Error 1. Recalibrate, Shift Adjust Can't Compensate More Than 100%
-
8/15/2019 Balanza Spider
25/332
Chapter 2: 3027 Over/UnderJumpers and Keyboard Functions
(11/97) 2-1
2 3027 Over/UnderJumpers and Keyboard
Functions
Display PCBW1 - Decimal Point, comma display
Out = decimal pt.; In = comma
W2 - ROM Select
Must short (1-2)
W3 - ROM Enable
Must be in
Power Supply PCBW1 - Setup Entry
In = enable; Out = disable
W2 - Internal Suppressor (Use with TTL outputs)
In = connect suppressor; Out = disconnect
Keyboard
KEY SETUP FUNCTION NORMAL FUNCTION
ZERO Back Up To Previous Step Re-Zero Scale
TARE/TARGET Toggle Selections Enter Target Or Tare
CLEAR Advance To [Caloff] Clear Tare Or Target Wgt
UNITS N/A Toggle Units (Lb/Kg)
PRINT Accept Selection Initiate A Print Command
-
8/15/2019 Balanza Spider
26/332
METTLER TOLEDO Industrial Quick Reference User’s Guide
(11/97)2-2
Softswitch Settings
F0-Span Adjust
1-Enable; 0-DisableF1-Operating Mode0 = NA; 1 = 3026; 2 = NA; 3 = 3036; 4 = NA;
F1.5- Indicator Mode0 = indicator; 1 = over/under
F2-Calibration Units0 = LB; 1 = KG; 2 = lb-oz; 3 = oz; 4 = g;
F3-Units Key 1-LB/KG; 0-Disable; 2 = NA; 3 = LB-g-OZF4-Weight/LED Enable
0 = wgt on, led off; 1 = wgt on, led on;
F4.1-Zone Width Entry
0 = Increments; 1 = % of target;F5-Zero Cursor
1-Enable; 0-DisableF6-Auto Zero Maint.
0 = disable; 1 = .5inc; 2 = 1inc; 3 = 3 inc.F6.1AZM in Net Mode
0 = gross; 1 = gross and net F7-Zero Key Enable
0 = disable; 1 = 2%; 2 = 20%;
3 = 20% GandNet F8-Motion Sensitivity
0 = 1d; 1 = 3d;F9-Filter Selection
0 = disable; 1 = light; 2 = medium; 3 = heavy9.1-Dig. Load Cell Filter
1-Enable; 0-DisableF10-Expanded Weight
1-Enable; 0-DisableF11-Net Wgt. Display
0 = gross wgt; 1 = net diff.
F12-Zone ProgrammingPrint = enter; Tare = skip
12.1-Setup Entry Point
0 = F0; 1 = F1212.2-High Zone Width
Tare = toggle; Print = Select
12.3-High Accept Width
Tare = toggle; Print = Select 12.4-Low Accept WidthTare = toggle; Print = Select
12.5-Low Zone WidthTare = toggle; Print = Select
12.6-Programmable Target Memory1-Enable; 0-Disable
F13-Tare Enable1-Enable; 0-Disable; 2 = auto tare
F14-Auto Clear Tare
1-Enable; 0-DisableF15-Serial Port Program.
Print = enter; Tare = skip15.1-Format
0 = cont. ;1 = demand15.2-Baud Rate
Tare = toggle; Print = Select
15.3-Parity0 = always 0; 1 = odd; 2 = even
15.4-Checksum1-Enable; 0-Disable
15.5-Line Format Select 0 = single line displayed; 1 = GTN single line;2 = GTN multiple line;
15.6-Double Wide Print
1-Enable; 0-Disable15.7-Auto Print
1-Enable; 0-Disable
15.8-Print Wgt. Class.1-Enable; 0-Disable
15.9-Stop Bits0 = 1; 1 = 2;
F16-ASCII Input 1-Enable; 0-Disable
F18-Tare Interlocks
1-Enable; 0-DisableF19-Motion Blanking
1-Enable; 0-DisableCAL-Calibration
Print = enter; Tare = skip
-
8/15/2019 Balanza Spider
27/332
Chapter 2: 3027 Over/UnderError Codes
(11/97) 2-3
Error Codes
Error Code Description Suggested Corrective ActionE1 Program Memory Fatal 1. Check DC Supply Voltages
2. Replace Display PCB
E2 Internal Ram MemoryFatal Error
1. Check DC Supply Voltages2. Replace Display PCB
E3 NOVRAM Memory Error 1. Check DC Supply Voltages2. Reprogram, Recalibrate3. Replace Display PCB
E8 Communication Loss with DLC 1. Check DC Supply Voltages
2. Check Interconnect Harnesses For Load Cell And PCB’s3. Replace Load Cell4. Replace Display PCB
E9 DLC Out Of Range, Under Capacity 1. Check For Mechanical Bind
2. Check DC Supply Voltages3. Replace Load Cell4. Replace Display PCB
E10 DLC Memory Verify Fatal Error 1. Check DC Supply Voltages2. Replace Load Cell
E11 DLC ROM Error 1. Check DC Supply Voltages
2. Replace Load Cell
E13 DLC EPROM Error 1. Check DC Supply Voltages
2. Recalibrate Scale3. Replace Load Cell
E16 Math Error 1. Press Clear Key To Clear Error, Check Program And Recalibrate
E32 Insufficient Test Used ForCalibration
1. Recalibrate With At Least 50% Of Programmed Scale Capacity
E34 Test Weight Over Cap 1. Check Capacity Programming, Use Test Weight Less ThanCapacity
E35 Calibration Error 1. Recalibrate, Shift Adjust Can't Compensate More Than 100%
-
8/15/2019 Balanza Spider
28/332
Chapter 3: 8140 Digital IndicatorJumpers and Keyboard Functions
(11/97) 3-1
3 8140 Digital IndicatorJumpers and Keyboard
Functions All jumpers are in the correct position for standard operation when the unit is
shipped. Check the jumper positioning to be certain they are correct for thisunit’s application.
W1 - External Memory (shorted)
W2 - Calibrate Enable (shorted-enabled, out-disabled)
W3 - EPROM Selection (shorted between 1 and 2)
W4 - Comma Enable (in-comma, out-decimal point)
W5 - Load Cell Output Selection - (pins 1and 2 = 2 mV/V; pins 2 and 3 = 3mV/V)
Zero - Back up to previous step.
Test - Yes or 1
Tare - No or 0
Clear - Skip to S File.
Print - Enter
-
8/15/2019 Balanza Spider
29/332
METTLER TOLEDO Industrial Quick Reference User’s Guide
(11/97)3-2
Softswitch SettingsTo enter the setup mode, press both the TARE and CLEAR keys, then release at
the same time.
F0 - Span Adjustment 1 to access
F1 - Expand Display1 to enable
F2 - Display Filtering
1-4 to enable low to highF3 - Tare Active
1 activeF4 - Tare Interlock
0 enabledF5 - Auto Clear Tare 1 enabled
1= when +/- 1/2 increment or more of motionare detected; 2 = +/- 2 increments or moreF7 - Pounds CalibrationF8 - Power Up PoundsF9 - LB/KG Switching
1 enabledF10 - Auto Zero Maint.
1 = enabled ± 2%; 2 = enabled ± 20%F11 Analog Verification
1 = enabled
F12 Printer Output 0 = disabled
Demand Mode
1 = Enabled2 - Baud Rate 300, 1200, 2400, 4800, 96003 - Checksum 0 disabled4 - Printer Select
1 = 307, 8804, 8806, 8855, 88602 = 8805 receive mode only3 = 8805 smart mode
4 = 8820/8830 (ram 1)
5 = 8820/8830 (rams 2 and 3)5- Data Format 0 = displayed weight only1 = single line gross, tare, net
2 = multiple line gross, tare, net F13 Net Zero Cursor
0 = gross only; 1 = gross and net F14 Under Zero Blanking
0 = blanks at 3% under;1 = blanks at 5 increments
CAL - Calibration Procedure
-
8/15/2019 Balanza Spider
30/332
Chapter 3: 8140 Digital IndicatorError Codes
(11/97) 3-3
Error Codes
Error Code Description Suggested Corrective Action
E1 ROM Error Try Power Down/ Replace main PCB
E2 Ram Error Try Power Down/Replace main PCB
E3 NOVRAM Error Try Power Down/ Replace Main PCB
E4 Print Fault Check Printer/Format
E5 Display Verify Error Replace Main PCB
E6 Analog Verify Error Recalibrate
E7 EEROM Error Try Power Down/Replace Main PCB
E8 Scale in Motion Waits Unit Motion Stops
E9 Illegal Configuration Reconfigure Increment Size
E10 Calibration Error Recalibrate
E11 Calibration Error Recalibrate
E12 Over Capacity Reconfigure
E13 Low Capacity Reconfigure
EA Insufficient Test Wt. Use more Test Weights/Try Again
AAAAAA Analog Verify Cycle None: This indicates an AV cycle is in process
-
8/15/2019 Balanza Spider
31/332
Chapter 4: M8141 Power SupplyJumpers and Keyboard Functions
(11/97) 4-1
4 M8141 Power SupplyJumpers and Keyboard
Functions
JumpersJU1 - Calibrate Enable (shorted-disabled, out-enabled)
JU2 - External memory (installed)
JU3 - 2mV/V or 3mV/V cell selection (in = 2, out = 3)
JU4 - EPROM selection (factory use only)
JU5 - Memory size selection (factory use only)
JU6 - Fiber Optics power (CH1)
1-2 = Powered in sleep and wake modes
2-3 = Powered in wake mode only
JU7 - Fiber Optics
1-2 = Powered in sleep and wake mode
2-3 = Powered in wake mode only
Keyboard0-9 Used to enter setpoint values, commodity ID, time and date, calibration/setupparameters, and tare weight.
FUNCTION Used in conjunction with time, date, setup and ID after data entry.Sleep: With no preceding data entered, this key will put instrument in sleep modeto conserve battery life.
ZERO/WAKEUP Zero: digitally zeros scale. Wakeup : if already asleep, used to re-initialize unit.
PRINT Initiates data outputs to a printer or other device.
LB/KG Mode selection-selects weight units to be used, pounds, kilograms, orother pre-programmed units.
NET/GROSS Mode selection- selects weighing mode.
TARE Enters the displayed weight as tare or is used with keys 0-9 to enter akeyboard tare.
CLEAR Erases erroneous keyboard entries.
-
8/15/2019 Balanza Spider
32/332
METTLER TOLEDO Industrial Quick Reference User’s Guide
(11/97)4-2
Setup ChartAccessCode Parameter
SelectableValue
AccessCode Parameter
SelectableValue
01 Scale Capacity 1 to 999,999 29 Tare Motion Interlock 0 = Disable, 1 = Enable02 Division Size 0.00001 to 200 30 Printer Data Format 1 = Single Line Weight
03 Print Motion Detect Band 0 to 3 2 = GTN on Single-Line
04 Acquire Dead Load Press ENTER key 3 = G-T-N on 3 Lines
05 Scale Span Enter Weight on Scale 4 = GTN on Single
06 Calibration Units 0 = kg, 1 = lb Line sign correct
07 Display Update Rate 1 to 255 5 = G-T-N on 3
08 Power Up Units 0 = kg, 1 = lb 31 Minimum Print Threshold 0=Disable, 1=up to Cap
09 Digital Zero/Tare Motion 0 to 3 32 Double Width Print 0 = Disable, 1 = Enable
10 Over Capacity Blanking 80 to 110% 33 Scale ID 0 to 12711 C0Z on Net or Gross 0 = Gross, 1 = Net 34 Print Scale ID 0 = Disable, 1 = Enable
12 AZM Delta Band 0 to 3 35 Setpoints 0 = Disable
13 AZM Delta Time Delay 1 to 15 1= Enable on Disp. Wt
14 AZM Aperture 0 to 125 2 =Enable on Gross Wt.
15 Digital Filter 0 to 3 36 Print Inhibit on Motion 0 = Disable, 1 = Enable
16 Display Blanking 0 = Enable, 1 = Disable 37 Zero Print Interlock 0 = Disable, 1 = Enable
17 Negative Gross Weight 0 = Prints Below Zero 38 Line Feed 0 to 10
Printing 1 = No Print Below 0 39 Commodity ID Entry 0 = Disable,
18 lb/kg Switching 0 = Disable, 1 = Enable 1 = Enable Fixed
19 Alternate Display Units Enter Cal/ Alt. units 2=EnableVariable
20 Time and Date 0 = Disable, 1 = Enable 40 Print Complete Time-Out 0 to 5
21 Time and Date Format 0 = None, 1 = US,2 = Canada
41 Dribble/Preact 0 = Disable
22 Printer Output Format Sect. 4.6, Parameter 22 1= Enable -Zero Tolerance
23 Channel 1 Baud Rate 0 = 300, 1 = 1200 2 = Enable -Wgt Tolerance
2 = 4800, 3 = 9600 42 CH 1 Configuration See Sect 4.6, Para. 42
24 Channel 2 Baud Rate 0 = 300, 1 = 1200 43 CH2 Configuration See Sect 4.6, Para. 43
2 = 4800, 3 = 9600 44 Auto Sleep Timer 0 to 255 Minutes
25 Tare Enable 0 = Disable, 1 = Enable 45 Remote Print Indicator 0 = Disable, 1 = Enable
26 Keyboard Tare 0 = Disable, 1 = Enable 46 Printer Checksum Enable 0 = Disable, 1 = Enable
27 Tare Auto Clear 0 = Disable, 1 = Enable 98 Parameter Setup Print all Current Setup
28 Tare Interlock 0 = Disable, 1 = Enable 99 Reset Parameters To Factory Setting
-
8/15/2019 Balanza Spider
33/332
Chapter 4: M8141 Power SupplyError Codes
(11/97) 4-3
Error Codes
Error Code Description
“--1--” A/D conversion error. The software detected an auto rangecondition during conversion. This can be caused by no load cellhooked up, load cell polarity reverse, or A/D hardware failure.
“--2--” Digital check error. The indicator has detected an internal error,
most likely a calibration data check error. Putting the indicator tosleep, and waking it up will cause the calibration data to be readback in from EEPROM. If the error still persists, then the EEPROMmay be bad.
“--3--” EEPROM read/write error. The indicator has detected a hardwareerror during read or write to the EEPROM. Putting the indicator to
sleep and waking it up will cause a read re-try. Putting theindicator in and out of the setup mode will cause a write re-try. If the error persists, the EEPTOM may be bad.
“--7--” A/D failure. The A/D conversion did not occur within 70ms. Thisis most likely a hardware failure in the A/D section.
“--8--” Setup calibrations not performed. This indicates that a parameter was changed, but the necessary calculations were not performed
to make the indicator operate. Since the calculations areautomatically performed on exit form the setup mode, this errordoes not normally occur. However, see documentation on the
ZERO button for a description of when it might.
Errors 4, 5, and 6 are reserved for future use. If they occur, contact the factory.
-
8/15/2019 Balanza Spider
34/332
Chapter 5: 8142 IndicatorJumpers and Keyboard Functions
(11/97) 5-1
5 8142 IndicatorJumpers and Keyboard
Functions
Main PCB JumpersW1 - ROM Enable: Must Be (IN)
W2 - Calibration Enable: (In = enabled, Out = disabled)
W3 - Comma Select: (In = comma, Out = period)
W7 - mV/V Selection: (1-2) 2mV/V load cell input; (2-3) 3 mV/V load cell input.
Dual Display PCB
JumpersW2 - Calibration Enable: (In = enabled, Out = disabled)
W5 - Primary Display Comma Select: (In = comma, Out = decimal pt.)
W6 - Auxiliary Display Comma Select: (In = comma, Out = decimal pt.)
W7 - ROM Enable: Must be (IN)
W8-A harness plugs onto this jumper from W2 on the Main PCB.
Rack Display PCB
JumpersW1-Primary Display Comma Select:(Same as W5 above)
W2-Auxiliary Display Comma Select:(Same as W6 above)
Optional BCD/Analog PCB(Dual Display Advanced Rack and Wall Enclosures Only)
BCD/Analog PCB Jumpers
W1-Motion Detect Inhibit: (1-2 = disabled, 2-3 = enabled)
W2-Calibration Enable:(In = enabled, Out = disabled)
-
8/15/2019 Balanza Spider
35/332
METTLER TOLEDO Industrial Quick Reference User’s Guide
(11/97)5-2
Keyboard Functions
During SetupENTER - accepts the displayed selection and advances to the next setup step.
SETUP - accepts the displayed selection and skips to[S FILE] at the end of setup.
ZERO - accepts the displayed selection and back-up to the previous setup step.
(0 - 9) - used to enter data as required. The 0 key is also used to display thenext selection when a menu of choices is presented.
Quick Reference Chart
Step Description Selections F2.1 Tare Mode 0 = Disable
1 = Keyboard/Auto 2 = Auto Tare Only
F2.2 Tare Interlocks (*) 0 = Disable 1 = Enable
F2.3 Auto Clear Tare 0 = Disabled 1 = Enabled
F2.4 Net Zero Cursor (*) 0 = Disabled 1 = Enabled
F2.5 Keystroke Timeout 0 = Disabled 1 = Enabled
F2.6 Predetermined Tare 0 = Disabled 1 = Enable French W&M
F2.7 Autoprint Threshold 0 = Disabled 1 = Enabled
F3.1 Power-up Timer 0 = Disabled
1 = Enabled
F3.2 Power-up Units 0 = kg Weight Units1 = lb Weight Units
Step Description SelectionsF3.3 Units Switching 0 = Disabled
1 = Enabled
F3.4 Expanded Weight 0 = Disabled 1 = Enabled
F3.5 Span Adjust 0 = Disabled 1 = EnabledF3.6 Display Under Zero 0 = Disabled
1 = Enabled
F3.7 Zero Adjust 0 = Bypass Zero Adjust 1 = Adjust Zero
F4.1 AZM Range (*) 0 = Disabled5 = 0.5 Increment 10 = 1 Increment 20 = 2 Increment 30 = 3 Increment
F4.1A AZM Mode 0 = AZM Gross Mode Only 1 = AZM Net or Gross
F4.2 Motion Range (*) 07 = 0.7 Increment
F4.3 Motion Rate (*) 03 = 3 Updates
F4.4 Digital Filtering 0 = Disabled1 = Light Filter 2 = Medium Filter3 = Heavy Filter4 = Very Heavy Filter
-
8/15/2019 Balanza Spider
36/332
Chapter 5: 8142 IndicatorQuick Reference Chart
(11/97) 5-3
Step Description SelectionsF4.6 Analog Verify 0 = Disabled
1 = Enabled
F4.7 Pushbutton Zero 0 = Disabled1 = ±2% of Capacity
2 = ±20% of Capacity F5.1 JN Port Mode 1 = Demand (Printer)
2 = Toledo® Continuous3 = Masstron® Continuous4 = Toledo® Short Form
F5.2 JN RS-422 Input 0 = Disabled 1 = Enabled
F5.3 JN Baud Rate 1200 Baud
F5.4 JN Port Checksum 0 = Disabled
1 = Enabled
F5.5 Printer Model Select 1 = Standard 2 = 8805 (Receive Only)3 = 8805 (Smart Mode)4 = 8820/8830 (Ram 1)5 = 8820/8830 (Ram 2,
3)
F5.6 Weight Line Format 1 = Displayed Weight 2 = Single Line G, T, N 3 = Multi Line G , T, N
F5.7 Double Width Print 0 = Disabled 1 = Enabled
F5.8 Minimum Print Increments
F5.9 Printed Legend (*) 1 = "lb" or "kg" 2 = "t" for tons3 = No Legend
F5.10 Negative Net Weight 0 = Disabled1 = Enabled
F5.11 Repeat Print 0 = Disabled 1 = Enabled
Step Description SelectionsF5.12 Demand Format 1 = WT, ID, T&D, CN
2 = IDT&D
WT, CN3 = ID
T&D, CNWT
4 = IDT&D
CNWT5 = T&D
IDCNWT
6 = T&DIDWT, CN
7 = ID, T&D, CNWT
8 = IDT&D
CN, WT
F5.13 Time/Date Format 0 = Disabled1 = MM DD YY2 = DD. MM. YY3 = YY MM DD4 = HH: MM PM MM DD YY 5 = DD. MM. YY HH: MM6 = YY MM DD HH: MM
F5.14 Print ID 0 = Disabled1 = Enabled
F5.15 Print CN 0 = Disabled1 = Enabled
F5.16 Net Sign Print (*) 0 = Disabled 1 = Enabled
F5.17 ASCII Remote Input 0 = Disabled 1 = Command Input Enabled2 = Demand/Continuous
-
8/15/2019 Balanza Spider
37/332
METTLER TOLEDO Industrial Quick Reference User’s Guide
(11/97)5-4
Step Description SelectionsF5.18 Autoprint/Interlock 1 = Disabled
2 = Print Interlock3 = Autoprint
F5.19 Additional Linefeeds 0 = Skip Linefeed Select
1 = Access Linefeed Select
F5.20 DSR Input Mode 0 = CLEAR1 = TARE2 = PRINT 3 = ZERO4 = Blank Display
F6.1 Recall ID 0 = Disabled
1 = Enabled
F6.2 Recall CN 0 = Disabled
1 = Enabled
F6.3 Recall Time & Date 0 = Disabled1 = Enabled
F6.4 Preset CN 0 = Disabled1 = Enabled
F6.5 Recall Setpoint Data 0 = Disabled1 = Enabled
F6.6 Access Clock Adjust
F7.0 Setpoint Programming Group F7.1 Setpoints Enable 0 = Disabled
1 = Enabled
F7.2 Setpoint Mode 2 = 2, Dual Speed Setpoints4 = 4, Single Speed Setpoint
F7.3 Tolerance Mode 0 = Setpoint Tolerance 1 = Zero Tolerance
Step Description SelectionsF7.4 Zero Tolerance Entry 0 = Disabled
1 = Enabled
F7.5 Tolerance Entry 0 = Disabled1 = Enabled
F7.6 Setpoint Password 0 = Disabled 1 = Enabled
F8.1 JW Port Tare Entry 0 = Disabled
1 = Enabled
F8.2 JW Port ID Entry 0 = Disabled 1 = Enabled
F8.3 Continuous Output 0 = Disabled 1 = Enabled
F8.4 JW Port Baud Rate 9600 Baud
F8.5 JW Port Parity 0 = Always a "0"1 = Odd Parity2 = Even Parity
F8.6 JW Port Stop Bits 1 = 1 Stop Bit 2 = 2 Stop Bits
F8.7 JW Port Checksum 0 = Disabled 1 = Enabled
F8.8 Alpha Barcode Input 0 = Disabled 1 = Enable
F9.1 JY Port Enabled 0 = Disabled
1 = Enabled
F9.2 JY Port RS-485 Input 0 = Disabled 1 = Enabled
F9.3 JY Port Baud Rate 9600 Baud
(*) - Requires specific selection for legal-for-trade applications. Recommended default selections are shown in .
-
8/15/2019 Balanza Spider
38/332
Chapter 5: 8142 IndicatorError Codes
(11/97) 5-5
Error CodesThe 8142 has 2 types of error codes, operational errors and calibration errors.
Operational Error CodesOperational error codes can occur during power up or while the 8142 is innormal operation. Do no