Download - Broder Son
-
IC-80-GTechSpec
* Rated Capacity Limiter...Standard
* Capacity on outriggers...18,000 lbs.
* Pick and carry capacity up to...11,700 lbs.
* Height...7 3
* Width...6 6
* Sheave height...up to 46
* Horizontal Reach...up to 40
* Tight turning radius
* 2-Wheel drive standard
* 4-Wheel steer standard
* 4-Wheel drive optional
* Powershift transmission
* Fully hydraulic controls for smoothprecise operations
* Independent outrigger controls
-
IC-80-1G
18'
18'RADIUS IN FEET FROM C ROTATION TO LOAD
(WT. 90 LBS.)
8'6' 10"
CL
10'
12'
16'
14'
10'
USE SINGLE PARTLOAD LINE FORLOADS TO 9000LBS.
6'4' 8' 14'12' 16'
L
(WT. 124 LBS.)
026'
USE TWO PARTLOADLINE FORLOADS TO 18000LBS.
22'20' 24' 30'28'
15
70
24'
20'
22'
26'
28'
34'
32'
30'
37'36' 60
30
45
1'-4 3/4"
11 1/2"
16'-11"
28'-2"
70
3 7/16
9'-7"
18 1/2" 12"
5'-9 1/2"
9"
57 1/8"
11'-7 3/4"
5'-10 1/4"
26 3/4"
6'-6"
7'-3"5'-8 3/4"
3'-5"
3'-6 3/4"
22
3'-0 1/4" 2'-7 1/2"7'-2"
21
1'-7" 12'-9 3/4"
MAIN BOOM OR EXTENSION CAPACITIES IN POUNDSCAPACITIES APPLY TO OPERATION ON FIRM LEVEL SURFACE
MAIN BOOM ANGLE
320027002500
45
10-FOOT BOOM EXTENSION - STRAIGHT OR OFFSET
BOOM EXTENSION LOADS MUST NOT EXCEED MAIN BOOM CAPACITY.
ARE 75% OF TIPPING LOADS. CAPACITIES BELOW BOLD LINE ARE LIMITED BY TIPPING.OTHER CAPACITIES ARE LIMITED BY STRUCTURAL OR HYDRAULIC CAPABILITY.
CAPACITIES ON OUTRIGGERS ARE 85% OF TIPPING LOADS. CAPACITIES ON RUBBER DO NOT PICK & CARRY WITH LOADS ON BOOM EXTENSION.
USE 0, 15 OR 30 FOR OFFSET BOOM EXTENSION.
1 0'
B O
O M
E X
T.
USE 0 FOR STRAIGHT BOOM EXTENSION.
CAUTION
30150 2250
0
22502400
302600
1700096005
18M A
I N
B O
O M
2830
26
2224
20
16
1214
810
6
41001700
775925
675
145012751075
22002500
2000
355032002800
310024252000
57507900
4150655055504650
1025014500
7700
FEET
LOADRADIUS 360 ROTATION
ON RUBBER ON OUTRIGGERS
30003500500060
42003300
700070
11700 18000
2650 4150
13001500
1150
230020001725
260024002250
380030002800
465037503100
840010400
6300655055504650
14500102507700
OVER FRONTON OUTRIGGERSON RUBBER
IC801G
-
IC-80-2G
RADIUS IN FEET FROM C ROTATION TO LOADL
(WT. 90 LBS.)
8'6' 10"
CL
18'
16'
12'
10'
14'
4' 6' 8' 10'
USE SINGLE PARTLOAD LINE FORLOADS TO 9000LBS.
12' 14' 16' 18'
(WT. 124 LBS.)
15
20' 22' 24' 26'
USE TWO PARTLOADLINE FORLOADS TO 18000LBS.
32'30'28' 34'
40' 60
30'
24'
22'
20'
26'
28'
32'
34'
38'
36'
40' 10" 70
30
45
0
24'-0" EXTENDED9'-6" RETRACTED
9"
18'-2"
31'-9"
70
18 1/2" 12"
C LOAD
1'-4 3/4"
L
11'-7 3/4"5'-9 1/2"
9'-7"
5'-10 1/4"
57 1/8"
6'-6"
C ROTATION
26 3/4
L
7'-3"
3'-0 1/4"2'-11"
5'-10 3/4"
3 7/16"
11 1/2"
22
12'-9 3/4"7'-2" 2'-7 1/2"
3'-6 3/4"
3'-5"
5'-8 3/4"
21
DO NOT PICK & CARRY WITH LOADS ON BOOM EXTENSION. CAPACITIES ON OUTRIGGERS ARE 85% OF TIPPING LOADS. CAPACITIES ON RUBBER
OTHER CAPACITIES ARE LIMITED BY STRUCTURAL OR HYDRAULIC CAPABILITY.ARE 75% OF TIPPING LOADS. CAPACITIES BELOW BOLD LINE ARE LIMITED BY TIPPING.
BOOM EXTENSION LOADS MUST NOT EXCEED MAIN BOOM CAPACITY.
MAIN BOOM ANGLE
320027002500
MAIN BOOM OR EXTENSION CAPACITIES IN POUNDSCAPACITIES APPLY TO OPERATION ON FIRM LEVEL SURFACE
10-FOOT BOOM EXTENSION - STRAIGHT OR OFFSET
217572528
USE 0 FOR STRAIGHT BOOM EXTENSION.USE 0, 15 OR 30 FOR OFFSET BOOM EXTENSION.
0
CAUTION
3015
3234
30
26002250
22502400---
---
0
525625
425
30 45
190017251500
2426
22
1820
1416
6
1012
8
5FEET
RADIUS
11501000850
2350190016001350
295025502450
5550455039503350
ON OUTRIGGERS
360 ROTATION
7800565040003000
ON RUBBER
9500145001025077006550
17000
LOAD
25001275
7000500035003000 3300
4200
60
1000900
1125
70
21001950
2300
16501450
1850
25002150
36502950
31002750
3300
40503650
55504550
ON OUTRIGGERSOVER FRONT
10200
62004650
8250
ON RUBBER
1160014500
77006550
10250
18000
IC-80-2G
-
IC-80-3G
2200750 2350110028
22502400260030
30150
------
02250
403836
3234
30
150200250
450350
650
140015001650
33004200700070
180019502150
25002700320045
30003500
605000
500600700800900
1000
115013001450
17501600
1950
100001400017000
RADIUS
255014
262422
1820
16
85010001150
16501350
2050
12108
56
FEET
320043005600
94007550
LOAD
255028003050340039004400520061007700
100001400018000
34005200
120013501550180022002700
245027503050
39003400
4400
4450610081001000011400
61007700
20'
RADIUS IN FEET FROM C ROTATION TO LOAD10'
8'
CL
6' 10"4' 6' 8'
14'
10'12'
16'18'
(WT. 90 LBS.)
18'
USE SINGLE PARTLOAD LINE FORLOADS TO 9000LBS.
14'12' 16'
L
22'20' 24' 26'0
USE TWO PARTLOADLINE FORLOADS TO 18000
36'
(WT. 124 LBS.)LBS.
32'30'28' 34' 40'38'
15
26'
22'24'
28'30'32'34'36'38'40'42'
46' 4"
44'46'
7060
30
45
3 7/16"
7020'-0"
37'-5"
11'-7 3/4"
21
3'-5"
5'-8 3/4"7'-3"
2'-7 1/2"7'-2"
12'-9 3/4"
3'-6 3/4"
6'-6" 9'-7"
LC ROTATION
57 1/8"
5'-10 1/4"5'-9 1/2"
26 3/4
4'-11"
22
5'-10 3/4"
11 1/2"
LC LOAD
12"18 1/2"
1'-4 3/4"
3'-0 1/4"
30'-0" EXTENDED11'-6" RETRACTED
9"
IC-80-3G
-
10'- 0"TURNINGRADIUS
11'- 7" RADIUS(23'-1" DIA)
CLEARENCE CIRCLE
3'- 3"RADIUSCORNER
CLEARENCE
1'-2" 9'-6"
AISLE WIDTH
4'-3"
9'-6"
-
IC-80-GGENERAL:
Weight: IC-80-1G IC-80-2G IC-80-3G4-Wheel Steer 16,050 lbs. 16,250 lbs. 16,650 lbs.4-Wheel Drive 16,650 lbs. 16,850 lbs. 17,650 lbs.
Boom Movement:Rotation Continuous Continuous ContinuousElevation 0 to 70 0 to 70 0 to 70Extension 12 ft. 14 ft. 6 in. 18 ft. 6 in.
Boom Speeds:Rotation 2.0 RPM 2.0 RPM 2.0 RPMElevation 10.0 sec. 10.0 sec. 10.0 sec.Extension 17.0 sec. 21.0 sec. 27.0 sec.
Turning Radius:(C/L of Outside Steering Wheel) 10 ft. 0 in.
Aisle Width for 90 Turn: 9 ft. 6 in.
ENGINE: Standard OptionalMake GM CumminsModel 3.0 EFI* 4B3.9Type Gas Diesel
No. Cyl. 4 4Displacement 181 CID 239 CIDHP @ Gov. Speed 69 80
* Electronic Fuel Injection with Dual Fuel
Fuel Tank Capacity: 20 Gallons
TRANSMISSION:2-Wheel Drive:
Powershift transmission with 4-speeds in forward and reverse. Provides powershifts at any engine speed in any gear. All shifting is done with a single lever electrical control mounted on the steering column. Multiple-disc clutch packs operated by solenoid valve provide forward, neutral, reverse and speed selection. Equipped with oil cooler and filter. Torque converter has stall ratio of 2.2/1.
Gradeability 63 percent.
Forward/Reverse Travel DrawbarGear Gear Ratios Speed PullFirst 5.72:1 4 MPH 10,500 lbs.Second 3.23:1 6 MPH 6,000 lbs.Third 1.77:1 12 MPH 3,200 lbs.Fourth 1.00:1 20 MPH 1,800 lbs.
AXLES:Front:
Planetary drive/steer axle with 11.625/1 ratio. Differential is No-Spin. Axle mounted rigidly to frame.
Optional 4-Wheel DrivePlanetary drive/steer axle with integral drop boximput for an overall 13.76/1 ratio. Differential isNo-Spin. Only available with mining and industrial tires.
Rear:2-Wheel Drive:
Axle with 1-1/2 degree oscillation in either direction.
Optional 4-Wheel Drive:Planetary drive/steer axle with 13.76/1 ratio including the reduction through the front-axle-mounted drop box. Differential is No-Slip. Oscillation is 1-1/2 degree in either direction. Only available with mining and industrial tires.
Forward/Reverse Travel DrawbarGear Gear Ratios Speed PullFirst 5.72:1 3 MPH 12,300 lbs.Second 3.23:1 5 MPH 7,000 lbs.Third 1.77:1 10 MPH 3,800 lbs.Fourth 1.00:1 17 MPH 2,200 lbs.
STEERING:Hydraulic steering unit with two cylinders attached to each axle. Rear axle is the primary steer. An electric switch in the operators compartment is used to select rear-wheel steering, four-wheel round steering or crab steering. Electronic sensors and control box automati-cally align the steering when a new mode is selected.
BRAKES: 2-Wheel Drive 4-Wheel DriveFront Internal wet Internal wet
disc brakes disc brakes
Rear Drum type Internal wet disc brakes
Parking Disc type Disc type
-
TechSpec
TIRES:2-Wheel Drive 10.00 x 15, load range J radial,
highway type tread.
4-Wheel Drive 10.00 X 15, mining & industrial, 16 ply rating.
CHASSIS:Cargo Deck:
64 square feet of deck area.* 14,000 lbs. capacity on deck when load is centered over or between axles.** A storage box is located in front cargo deck. Steps located on front corners.
* 54 Square feet with Cummins engine.**14,000 pounds allowed at creep speed of 200
feet in 30 minutes.
Outriggers:Four hydraulic outriggers of box beam construction with direct-connected holding valves. Independent controls for each outrigger. Each cylinder equipped with direct-connected holding valves. Outrigger pad dimension 9x12.
Accessory Storage Box:Storage box located in front cargo deck.
Lifting RingsLifting rings at each corner of cargo deck so sling canbe attached for lifting crane.
OPERATOR COMPARTMENT:Operators control station provides one-position access to all operating functions. Includes adjustable operators seat, retracting seat belt, fire extinguisher and bubble level.
ELECTRICAL:12 Volt System
Instrument Package:Fuel, ammeter, oil pressure, water temperature, transmission oil temperature gauges & hourmeter. Also included are warning lights for low transmission pressure, turn signal, high beams, hazard lights, parking brake & 4-wheel drive.
Lighting Package:One pair headlights with Hi and Low beams, back-up lights, integral tail, brake, front and rear turn signals and emergency flasher switch at operators station. 12V horn actuated by button on shifting control.
ELECTRICAL: (Contd)Back-Up Alarm:
Provides pulsating sound from 97 dB alarm when transmission is in reverse. Conforms to SAE J994b.
Outrigger Alarm SystemTwo-tone alarm is activated when outrigger downcontrols are operated.
HYDRAULIC SYSTEM: Tandem pump, direct-driven by engine crankshaft, rated at 17 & 32 GPM at rated RPM. Hydraulic oil tank capacity of 22 gallons.
BOOM ASSEMBLY:Three-section boom assembly equipped with bearing pads, double-acting hydraulic cylinders with direct-connected holding valves & boom angle indicator on each side of boom.
Boom Rotation:Heavy-duty ball bearing rotation gear with external teeth. Rotation is powered by hydraulic motor and worm gear drive.
Boom Hoist:Turret mounted planetary gear hoist hydraulically powered with a bare drum line pull of 10,000 lbs. at a line speed of 110 FPM. Includes downhaul weight, swivel hook & sheave block for 2-part line and 125 ft. of 9/16 hoist rope.
Anti-Two-Block Device:Prevents damage to hoist rope and/or crane components from pulling load hook against tip.
Sheave Block, Two-Part:Single sheave block for 2-part line requirements.
Rated Capacity Limiter:Warns operator of impending overload with audibleand visual signals. Prevents overload by stoppingboom functions that cause overloads.
-
Copyright 2003 Broderson Manufacturing Corp. Specifications Subject to Change Form #CC103G (8/03)
MODELS:IC-80-1G Industrial Crane with
82-202 BoomIC-80-2G Industrial Crane with
96-24 BoomIC-80-3G Industrial Crane with
116-30 Boom
ENGINE:Diesel EngineCummins - 4B3.9
Spark Arrester MufflerInstalled in addition to std. muffler.
Catalytic ConverterReduces engine emissions.
Engine HeaterEngine coolant heater installed tocirculate warm water throughengine. Plugs into 120 volt AC.
Ether Injection SystemEther starting aid controlled byswitch in operator compartment andinjects ether directly into intakemanifold.
Engine Shut Down GaugesShuts engine off when high watertemperature or low engine oil pressure occurs. (Diesel Only)
AXLE & STEERING OPTIONS:4-Wheel Steer & 4-Wheel Drive
TIRE OPTIONS:Mining & Industrial Tires
10.00 x 15 , 16-Ply Rating10.00 x 15, Non Marking
Solid Rubber Tires: 8.25 x 15 8.25 x 15 Non-Marking
Foam Filling of TiresSpare Tire & Wheel
Highway Tread, 10.00 x 15Mining & Industrial, 10.00 x 15Mining & Industrial, Non Marking
CHASSIS OPTIONS:Auxiliary WinchMounted behind front bumper,hydraulically driven with control inoperators console.
Listed below are brief descriptions of each option available for the IC-80-G Industrial Cranes.Consult the IC-80-G Engineering Spec for additional information on each option.
CHASSIS OPTIONS: (Contd)Pintle Hook:
Pintle Hook, RearPintle Hook, Front
Headlight and Taillight GrillesWelded steel protective grilles for headlights and taillights.
Rear Work Light GrillesProtective grilles for worklights.
Rearview MirrorsOne mounted on right-hand deckstake & one mounted on left-handdeck stake.
OPERATOR COMPARTMENTOPTIONS:
Operator GuardTubular steel weldment with heavy expanded steel mesh top section.
Operator Guard CoverClear vinyl cover which goes overOperator Guard, for inclementweather operations.
Operator Guard DoorHinged door covers operator com-partment side opening.
All-Weather CabRigid-mounted canopy section &removable hinged door. Includesheater, electric windshield wiper,one sliding glass window in the door& one in the right side of canopy.Defroster fan & dome light included.
Cab HeaterHeater with two-speed fan for unitswithout All Weather Cab.
Windshield WasherIncludes reservoir pump and nozzle.
Floor MatVinyl mat with foam backing.
Operator Suspension SeatProvides additional operator com-fort.
Noise Reduction KitIncludes floor mat, control valve andside panels of foam backed vinyl fornoise reduction.
Air ConditioningAir Conditioner with R134 coolant.
ELECTRICAL OPTIONS:Strobe LightsYellow strobe light mounted on eachside of turret weight box.
Amber Rotating BeaconsAmber rotating beacon mounted oneach side of turret weight box.
Boom Work LightsOne work light mounted to boom tolight boom tip and one work lightmounted to turret to light groundunder boom tip.
Work Lights-RearTwo work lights recessed in rearbumper.
BOOM ATTACHMENTS:Boom Extension, 10 FootBoom stowable.
Boom Extension, 10 Foot, OffsettableSame as above item, except theboom extension is offsettable to 3 different positions; 0 degrees(inline), 15 degrees and 30 degreesoffset.
Searcher Hook:Nose Mount
Should you, as an end user,require an option or specialequipment on your IC-80-G thatis not listed on our sales litera-ture, please contact your dealersalesperson or the factory toreceive a special quoted price.
IC-80-G