Cellulose Fibers and Microcellular Foam Starch Composites
Richard A. Venditti*, Joel J. Pawlak, Andrew R. Rutledge, Janderson L. Cibils
Forest Biomaterials Science and Engineering NC State University, Raleigh, NC
Outline
• Introduction to Starch Microcellular Foams• Objective• Procedures• Results and Discussion• Conclusions• Further Work• Acknowledgements
Microcellular Starch Foams• SMCF production methods
(avoids drying from high surface tension liquids)
– Freeze Drying – rapid freezing, many nucleating sites
– Multiple Solvent exchange• Example: 8% aqueous solution of
unmodified wheat starch, equilibrated with 40, 70, 90, 100, 100, 100 % ethanol solutions
– Supercritical Fluid Extrusions
– Glenn, et al, J. Agric Food Chem, 2002.
– Venditti and Pawlak and coworkers, 2007 and 2008.
The pressure exerted on the plates separated by a 0.01 micron layer of water is approximately 142 atmospheres.
δ
Laplace Equation simplified for liquid between 2 plates.
water P1 P2
δγ2
12 =−=Δ PPP
Cell wall
Cell wall
SEM of Uncooked Starch and SMCF
7.5g glutaraldehyde / 100g starch Length scale is 20 microns
Uncooked Starch
80
90
100
0 5 10 15 20 25 30 35
Glutaraldehyde, %
Bri
ghtn
ess
(ISO
)
Microcellular Starch Foams• Microcellular starch foams: a starch based
porous matrix containing pores ranging from 2 micrometers to sub-micrometer size
• Cell densities > 109 cells per cm3 • Specific density reduction of 5 to 98% of
matrix material• SMCF materials have high specific surface
areas (air-solid interfaces). – SMCF from CO2: 50-150 m2/g– Calcium Carbonate: 2-6 m2/g– TiO2: 8-25 m2/g
• Coatings and filler particles made from microcellular foams are expected to be excellent in their ability to scatter light and be strong opacifying materials
Micrographs of SMCF created by freeze drying starch (top) and starch/AKD(middle) Also shown is SMCF created by solvent exchange (bottom).
B
B
C
Structure of SMCF FoamsGlenn, Agricultural Materials as renewable resources: nonfood and industrial applications, ACS, 1996.
Beaded Polystyrene Puffed Wheat Freeze Dried Starch
100 microns
20 microns5 microns
SMCF particle formed under shear SMCF formed from molded aquagel
Challenges
• The mechanical properties are poor,especially during processing
• Moisture properties are such that these materials are very humidity sensitive
Objectives
• Produce tougher SMCF materials via composites with wood fibers
• Carbonize and reduce the humidity sensitivity of such materials as well as modify other properties, such as chemical inertness
• Understand the effect of carbonizing temperature on the properties
Procedures
• Production of starch-fiber aquagels• Solvent exchange process and drying• Carbonization Process• Analysis
Cooked Starch-Fiber
Cooling to form stiff gels
Ethanol Exchanges
Carbonization
Sample Preparation Procedures
120 s microwaveMax Temp 90 CStirring every 15 s
Tube FurnaceNitrogen atmosphere0.5 C/min heat/cool ramp
Also: TGA Furnace with Nitrogen ramped at 10C/min
2X gel weight7 exchanges24 hrs
24 hoursTemp: 5 C
Results: Composition Effects28% AMYLOSE Shape Strength 16% starch - no fiber Mostly clumpy poor drying Good 12% starch - no fiber Warped and clumpy Good 8% starch - no fiber Loss of volume, poor shape Brittle 8% starch - 3% fiber Warped Good 8% starch - 4% fiber Warped Good 8% starch - 5% fiber Good shape but clumpy Good 50% AMYLOSE 10% starch - 3% fiber Maintained shape/smoothness Good 10% starch - 4% fiber Maintained shape/smoothness Good 10% starch - 5% fiber Maintained shape/smoothness Good HIGH AMYLOSE 15% starch - no fiber Cracked upon drying None 12% starch - no fiber Cracked upon drying None 15% starch - 1% fiber Cracked upon drying Brittle 15% starch - 2% fiber Cracked upon drying Poor 15% starch - 3% fiber Maintained shape/smoothness Good 14% starch - 3% fiber Maintained shape/smoothness Good 12% starch - 3% fiber Maintained shape/smoothness Good 12% starch - 4% fiber Maintained shape/smoothness Good 12% starch - 5% fiber Maintained shape/smoothness Good
Composition Effects• Increased amylopectin improved strength
properties of the foams• Increased amylose improved the shape
smoothness of the molded parts• Increased amylose increased the density of
molded parts• Increased fiber content up to 5% improved the
structure (decreased density) and toughness• Above 5% fiber content the foams were had an
uneven distribution of fibers
Composition Effects
• Increased fiber content up to 5% improved the structure (decreased density) and toughness
• Above 5% fiber content the foams had an uneven distribution of fibers
Procedures: Mechanical ProptsCompression testing on a MTS Model Alliance RF300 with 60,000 lb
frame and 260 lb Omega load cell. Strain rate of 0.5 mm/min.
Heat Treatment/Carbonization of SMCF-Fiber Composites
• Heat treatment at 200 C produces a wood-like foam material of low density (0.45 g/cc)
• Produces a low density (0.20 g/cc) porous carbon microstructure
• Inert, strong, low density (0.20 g/cc) foam upon heating to 350 C and above
200 C Untreated 350 C
Effect of Treatment Temperature on Yield:SMCF-Fiber Composites
0
20
40
60
80
100
120
0 200 400 600 800
Temperature, C
Yield, %
Effect of Treatment Temperature on Density:SMCF-Fiber Composites
0.00
0.10
0.20
0.30
0.40
0.50
0.60
0 200 400 600 800
Temperature, C
Den
sity, g/cc
Dimensional Changes vs Treatment Temperature:SMCF-Fiber Composites
‐20
‐10
0
10
20
30
40
1 2 3 4 5
Temperature, C
Shrink
age, % X-Y Plane
Z-Direction
Compression Testing Results
0
1 0 0
2 0 0
3 0 0
4 0 0
0 1 2 3 4
O m e g a L o a d c e ll ( N )
C r o s s h e a d ( m m )
[ 3 ]S
P
B
M
0
1 0
2 0
3 0
4 0
5 0
6 0
7 0
8 0
9 0
0 . 0 1 . 0 2 . 0 3 . 0
O m e g a L o a d c e ll ( N )
C r o s s h e a d ( m m )
[ 1 1 ]
S
P
Y
B
M
Typical results for untreated and treated at 200 C.
(Note Y-axis max is 400 N)
Typical results for 350 C and higher treatment temperatures.
(Note Y-axis max is 90 N)
Effect of Treatment Temperature on Mechanical Properties:
Increases in viscosity improve pore structure and brightness.
Effect of Treatment Temperature on Weight NormalizedMechanical
Properties:
Increases in viscosity improve pore structure and brightness.
Results from study:• Particles with a fine porous structure and high
brightness can be formed with the described solvent exchange method
• Crosslinking/Molecular weight found to improve pore structure and optical properties
• The resulting SMCF particles absorbed water rapidly and lost structure upon wetting
• Water resistance must be increased
Challenges
• The major challenge still remains to control the wetting properties of the SMCF
• Blending, derivatization and crosslinkingare being explored as approaches to development of water resistance
• Alternative methods of foam formation including carbon dioxide assisted extrusion are also being explored to modify pore structure